TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever...
Transcript of TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever...
![Page 1: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/1.jpg)
RENESSE
Thank you for your recent purchaseof the TOTO® product. Please read theenclosed information to ensure the safe use of your product. .
Installation and Owner’s Manual
2007.5
•
™
0GU3025
TL170SD
Important Safeguards------------1~2Specifications -------------------------3Before Installation--------------------3Set-Up Drawing -----------------------4Components ---------------------------5Installation Procedure ---------6~9How to Use ---------------------------10Maintenance --------------------11~12Troubleshooting --------------------13Replacement Parts------------------14Warranty -------------------------------15
Single Handle Lavatory Faucet
Contents
®
English Español Français
![Page 2: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/2.jpg)
1
EN
GLIS
H
Important Safeguards (For your safety, please follow the instructions below)
Warning Do not reverse the hot and cold water inlet. You may be scalded if they are reversed.
Do Not Do not use hot water supply that is higher than185˚F (85˚C). If water is hotter than 185°F is used, do not use steam for hotwater supply. If it is broken, property damage, scalding, andother injuries may occur.
Do not disassemble
Do not disassemble or modify the item in anyway not described in this manual.
If the system is broken, property damage, scalding and otherinjuries are likely to occur.
Read the “Important Safeguards” section thoroughly before installing the product.
Warning
Caution
●The following symbols indicate safe and proper use of the product. Failure to observe them may reult in injury or property damage.
Failure to observe this symol may result in serious injury.
Failure to observe this symbol may result in injury or property damage.
Absolutely Do NOT.
Do not disassemble
Mandatory!
The following table demonstrates the use of safety symbols in this manual.
Less than185° (85˚C)
HC
Hot water Cold water
Do Not
Caution
Do notTouch You may get scalded when they are hot.
While using hot water do not touch the spoutand spout body directly.
Do not strike or kick the product If the system is broken, property damage, scalding, and otherinjuries may occur.
Do not use the product at temperature excedingwhat local codes allows. If parts are damaged, property damage, scalding and otherinjuries may occur.
HOT
Ah!
Freezing
![Page 3: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/3.jpg)
2
EN
GLI
SH
When the valve at the hot side is opened, hot water may cause scalding.
To use hot water, you must turn the handleon the cold side first, then turn the handle on the hot side slowly and adjust the temperature.
After water is turned off, leave the handlein turned off, leave the hand in the coldside or in the middle.The next time hot water is used, the hot water remaining in the valve may cause scalding.
Before using hot water, check with yourhand that the temperature is appropriate.
When the handle on the hot side is turned, hot water may cause scalding
Warning
Mandatory
Ah!
HOT Do not
If the system has deteriorated or worn-out,property damages, scalding and other injuries may occur.
Check water leakage and looseness in the pipe (cabinet and inspection hole etc.) regular.
If the hot water pressure is higher than thatof the cold water, you will not be able to adjustthe temperature normally, and you may be scalded.
The pressure of the water supply can notbe lower than that of the hot water.The hot water pressure must be lower than thepressure of the cold water side.
Ah!
Nolooseness
Noleakage
Slowly
![Page 4: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/4.jpg)
3
EN
GLIS
H
34 104˚F (2˚C 40˚C)
Specifications
Cold and hotwater pressure
Minimum pressure
Maximum pressure
20psi ( 0.14MPa) (flowing pressure)
Maximum use temperature
Suitable Water Quality
Suitable ambient temperture
Supply Connection
125psi (0.86MPa) (static)
Less than 185°F (85˚C)Water that meets National/Primary
drinking water regulation
3/8” NPSM
Before installation
●To prevent being scalded due to malfunction, the water supply pressure must be higher than the hot water pressure, or you can make them equal. In addition, if you inrease the pressure of the hot water, it must still be lower than that of water supply side.
● If the water supply pressure is higher than 0.86MPa, you should buy a reducing valve to reduce the pressure to the range of 0.2-0.3MPa.
To use the faucet comfortably, the recommended pressure is about 0.2-0.3MPa.
●To prevent being scalded due to malfunction, the recommended hot water supply temerature is 140°F.
Max. 2.2gpm (8.32L/min)Flow Rate
![Page 5: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/5.jpg)
4
EN
GLI
SH
Flex Hose(Hot)
Flex Hose(Cold)
Push button(only for faucetwith pop-up drain)
Gasket
GasketFlat packing
Winged packing
Connector Assembly
Spout mounting nut
Components
Check that you have the following parts from the package.
Faucet main body parts
Some parts may be different depending on the model.
Flat washer
Lever
Outlet
Lock washer
Spout mounting flange
Spout Key
*Observe all local plumbing codes.*Make sure that water supply is shut off.*Read these instrutions carefully to ensure proper installation.*For new lavatory installation, install the faucet before installing the lavatory.
Installation andOwner’s Manual
![Page 6: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/6.jpg)
5
EN
GLIS
H
Set-Up Drawing*Some parts may differ from the illustration depending on the model.
3/8” NPSM
5” (1
27m
m) (
CLO
SE)
6-7/
16” (
163m
m) (
OPE
N)
2-15
/16”
(75m
m)
5-5/16 “(135mm)
1-11/16” (43 mm)
5
0 ° 5 0 °
Pop-up Drain cable connector
counter hole φ 1-5/16” to 1-7/16 (φ35±2 mm)
HOT COLD
cable length = 13-13/16” (350 mm)
1-1/4” OD (32 mm OD)
8-9/16” (218 mm)
18-3/16” (462 mm)
Deck ThicknessMax. 1-3/16” (30 mm)
5-5/16 “(135mm)
3-11/16” (94 mm)
![Page 7: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/7.jpg)
6
EN
GLI
SH
1 Clean the cold/hotwater supply pipes
1 Clean the cold/hot water supply pipes Before installation dirt and debris in the cold/ hot water supply pipes must be washed out
Important
2 Install the spout
3 Connect the cold/hot flexhoses
5 Pop-up drain with cable.
Installation Procedure
2 Install the spout.
③Insert the packing through the cold/hot water supply hoses into thegroove in the bottom of the main faucet body and into the installation hole.
②Measure the installation holes, select from the two kinds of packing to suit your needs.
④Insert the spout mounting flange, flat washer, lock washer and nut throughthe faucet mounting shaft in thatorder, face the spout to from the frontand attach the parts.
①Wipe dirt away around the instllation hole.
spout mountingflange
Faucet mounting shaft Cold Water
supply hose Hot water supply
hose
Packing
Faucet mounting shaft
Section
Flat washer Lock Washer
Nut
Spout
Close
4Pop-up Drain with Cable installation
(Only for faucet withPop-up drain).
![Page 8: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/8.jpg)
7
EN
GLIS
H
3 Connect the cold/hot water supply hoses
*Put the gasket into the connectors and tighten the connectors in the stop valves; use the tool to fasten them.*Put the gasket into the cap nuts of the cold/hot flex hoses, screw in the connector, use the tool to fasten them.
Flex hose(Hot)
Flex hose(Cold)
Cap nut
Gasket
GasketConnector
Stop valve
![Page 9: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/9.jpg)
8
EN
GLI
SH
The minimum bending radius of the hose is 2 3/8”(60mm), if you bend it over the limit, it will break, which may cause early damage. ●During installation, do not bend the hose from the end surface of the main faucet body too far. ●Do not pull the hose violently. This may break the hose.
If the external reinforced layer of the hose is damaged due to friction, the hose performance will deteriorate.
●Avoid unnecessary contact of similar hoses.
●You have to bend the hoses, but be careful not to break them.
Hot watersupply hose Cold water
flex hose
R= 2 3/8” (60mm)and higher
R=2 3/8”(60mm) and higher
Cautions for installing flex hoses
Good Bad Bad Bad
![Page 10: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/10.jpg)
9
EN
GLIS
H
cabletailpiece
u-cup seal
drain body pop up
nut
drain seal
cable handleconnector
cable baseconnector
cable
lock nut
tailpiece
drain body
locknut
drain gasket
flange nut
drain body
flange
lavatory
cable
cable handleconnector
cable baseconnector
press the clip tobe able to connect
clip
clip
groove, to which connectionis to be made
4 Pop-up Drain with Cable Installation(Only for Faucet with Pop-up Drain)- Apply pipe tape to the flange threads.
- Insert flange into the drain hole.
- Assemble the gasket. flange nut and lock nut.
- Apply pipe tape to the end threads of flange threads and install the tail piece to drain body
-Make sure that cable faces toward the faucet.
- Connect the cable base connector with cable handle connector.
Push button
faucet handle
Push button
![Page 11: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/11.jpg)
EN
GLI
SH
How to UseHow to adjust the temperature
If it is fully turned to the left side, the water temperature is at its highest.
Turn the leverFor cold water, turn it to the right side, forhot water, turn it to the left side.
To prevent scalding due to malfunction,the recommended hot water supplytemperature is 140°F (60˚C).
Right side
(Cold)
Lever
Left side(Hot)
Close
Drain
Drain
Push button
Push
Push button
Push
Open
Open and close the Pop-up valve(Only for Faucet with Pop-up drain )
Push the push button. When the pop-up is closed, water can be kept in the washbasin. Push it again, the drain is opened and water will drain out.
10
![Page 12: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/12.jpg)
11
EN
GLIS
H
Maintenance
1. Unscrew the aerator.
3. Install the aerator.
Use attached special tool to remove it.
Use spout key provided to install it.
Brush
Aerator
Spout key
Unscrew
For best performance and sanitary environment, please maintain it everyday.
Maintain the outlet
2. Use a brush to clear the dirt and debris from the aerator.
Be careful not to lose the parts when they are removed.
Use a cloth to clean it
Use water and a damp cloth to wipe away the dirty completely.
●Slight dirty
●Seriously dirty Use a cloth with dilute detergent to wipe away the dirt, then wash and dry it.
Aerator
![Page 13: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/13.jpg)
12
EN
GLI
SH
●Acidic cleaning agents, alkaline cleaning agents, bleaches except for the TOTO scale cleaner. ●Solvents like thinner and benzene
Notes:
Do not use the following materials, whichare harmful to the faucet surface finish.
●Cleaning agents like cleanser or grinding powder that contain coarse particles ●Nylon scrubbers and brushes
No looseness
Confirm looseness in the main body
In case of looseness, request for service to the installer, distributor or Tech Support.
If you still use it when the main body breaks loose, it will cause leakage due to the load on the pipe.
1.For maintenance press the push button at first
pop up
drain body
pop up
Unscrew the pop up counterclockwise and take it out of the drain body
Cleaning utensil such as small brush can be used to clean the pop up
pop up
small brush
Push button
Push
Open
Cleaning Drain
Looseness in the main body
Unscrew
![Page 14: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/14.jpg)
13
Troubleshooting
Do you lower down the lever handle tostop position? (is it set to fully closed?)
Is the stop valve fully opened?
Is the aerator blocked with debris?
Is the outlet hole frozen?Check local codes with professional help and apply hotwater to the outlet.
Clean the aerator.
Use stop valve to adjust flow.
Lower the lever handle tostop position.
―
―
P.7
P.9
―
Water flowswithout stop
Flow is too small When gas water heater device is used
with the product, is the switching method set properly?
Set the gas hot water device properly with professional help.
Is the stop valve on the cold side fully opened?
―
―
―
―
―
Adjust flow with stop valve
Does the water heater give enough hot water
Check settings and functionson the hot water device
Is the aerater blocked? Page 9Clean the aerator
Too hot
Tool Cold
Temperaturecan not beadjustedeasily.
If you do not understand the position of the stop valves, ask the installer for help.
ExplanationProblem
The parts of the product need ”breaking” for a few days before they become stable. This is not a problem
The handles become harder to turn than when you started to use the product.
● You can encounter the following during use. This is not a problem
Before contacting a repairman, check the following common problems and solutions.If the problems perists, contact your dealer or tech support
Check SolutionProblem Refer to
Is the stop valve on the hot side fully opened?
Adjust flow with stop valve
Is the stop valve on the cold/ Hot sidesfully opened?
Adjust water flow with stop valve
Does the water heater give adequate water?
Check settings and functionson water heater withprofessional help
EN
GLIS
H
![Page 15: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/15.jpg)
Replacement Parts
14
EN
GLI
SH
Set screwLeverValve cover
Spout Kit
Spout mounting kitaerator
Flex hose (Hot)Flex hose (Cold)
Drain Assembly
Cartridge
Connector assembly
1
No.123
Description
456789
1011 2
8
34
5
6
7
910
11
![Page 16: TL170SD RENESSE Contents - TotoUSA.com€¦ · 13 Troubleshooting Do you lower down the lever handle to stop position? (is it set to fully closed?) Is the stop valve fully opened?](https://reader033.fdocuments.us/reader033/viewer/2022050519/5fa28f621904961e3f7ee397/html5/thumbnails/16.jpg)
WARRANTY
©2007 TOTO USA, Inc. á 1155 Southern Road, Morrow GA 30260Phone (888)-295-8134 Fax (800)-699-4889 www.totousa.comTOTO USA, INC. is a wholly owned subsidiary of TOTO Ltd.
Printed in August, 20070GU3025
LIFETIME LIMITED WARRANTYWarranty applies to selected residential faucets only.1. TOTO® warrants its faucets (“Product”) to be free from defects in materials and workmanship during normal residential use for as long as the original consumer end-user purchaser owns their home. This limited lifetime warranty is extended only to the original consumer end-user purchaser and only so long as the Product remains in use by the original consumer end-user purchaser in its original place of installation in the purchaser’s residence. This warranty applies only to Product purchased and installed in North America.2. TOTO® obligations under this warranty are limited to repair or replacement, at TOTO®’s option, of Product or parts found to be defective in normal residential use, provided that such Product was properly installed and used in accordance with the owner’s manual. TOTO® reserves the right to make such inspections as may be necessary in order to determine the cause of the defect.3. This warranty does not apply to the following items:
Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc.Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, or improper care, cleaning or maintenance of the Product.Damage or loss resulting from sediments or foreign matter contained in a water system.Damage or loss resulting from improper installation or from installation of the Product in a harsh and/or hazardous environment, or improper removal, repair or modi cation of the Product.Damage or loss resulting from the use of an abrasive cleanser.
4. If the Product is used commercially, TOTO® warrants the Product to be free from defects in materials and workmanship for one (1) year from the date the Product is installed, with all other terms of this warranty applicable except the duration of the warranty.5. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.6. To obtain warranty repair service under this warranty, you must take the Product or deliver it prepaid to a TOTO® service facility with proof of purchase (original sales receipt) together with a letter stating the problem, or contact a TOTO ® distributor or products service contractor, or write directly to TOTO® U.S.A., INC., 1155 Southern road, Morrow, Georgia 30260, (888) 295-8134. If, because of the size of the Product or nature of the defect, the Product cannot be returned to TOTO®, receipt by TOTO ® of written notice of the defect together with proof of purchase (original sales receipt) shall constitute delivery. In such case, TOTO®
may choose to repair the Product at the purchaser’s location or pay to transport the Product to a service facility. THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO®. REPAIR, REPLACEMENT OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. TOTO® SHALL NOT BE RESPONSIBLE FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED. IN NO EVENT WILL TOTO®’S RESPONSIBILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.