• Very good bonding strength.

• Flexible.

COVERAGE• A 25 Kg. bag of DAVCO SUPER TTB

covers 5 - 6 sq.m. depending ontile size and weight, substratesand bed thickness.

PACKAGING• 25 kg. bag

STORAGE•

60 x 60 cm. and Up No slip Excellent Bonding

25 Kg. bag of DAVCO STTB covers approximately 5 - 6 sq.m.

SUPER TTB

A high quality tile adhesive, with added polymers.

CHARACTERISTICS

DESCRIPTION

USES

COVERAGE

• Tile on wall and floor.

• Interior/Exterior.

• Large tiles and low porous tiles 60x60 cm. and more.

• Substrates: cement, mortar.

HIGH QUALITY CEMENT BASED TILE ADHESIVE

| ENGLISH VERSION 10/60 1 |

Tile Adhesive

Size of Trowel Coverage Size of Tile

4x4 mm. 12.5 sq.m.

6x6 mm. 7.5 sq.m.

Mosaic or Small TileUp to 10x10 cm.

Medium TileUp to 30x30 cm.

10x10 mm. 5.6 sq.m.

12x12 mm. 4.6 sq.m.

Big Tile, Thick Bed ApplicationMore than 30x30 cm.

Big Tile, Thick Bed ApplicationMore than 30x30 cm.

**Actual filed performance will depend on installation and site condition. 1 year from date of manufactureif stored in unopened originalpackaging in dry condition. WORK INSTRUCTIONS

Surface preparation1. Surface must be clean and without any trace of oil.

2. Painted surface must be abreded to expose at least 80% of the original

substrate.

3. New concrete must be allowed to cure for at least

28 days.

4. New render must be allowed to cure for at least 7 days.

• Temperature range for use : 5oC to 35oC.

• Wear gloves and safety goggles.

PRECAUTIONS

Application1. Use a proper notched trowel to spread the adhesive

onto the substrate with the flat side of the trowel

until it is smooth.

2. Use the notched side of the trowel to create an

even adhesive bed. minimum bed thickness is

- 2 mm. for wall.

- 3 mm. for floor.

(size depends on the thickness of tiles).

3. Ensure the adhesive is wet when the tiles are laid

and tapped into the position to ensure full contact

with the adhesive. Do not spread more than 1 sq.m.

at once.

4. Once the tiles have been laid, leave to stand for 24

hours or the tile adhesive is dry before grouting

with Davco Tile Grout.

1. Slowly add DAVCO STTB 25 kg. to a bucket of

clean water (mixing ratio for 25 Kg. bag: 6-6.5 Litres

of water).

2. Use power drill to mix until a thick creamy consistency

is achieved.

3. Allow the mixture to stand for 1 - 3 minutes for

chemical slaking and reducing air bubble, then remix

before using the adhesive.

Product preparation

Bulk Density (Kg./L.) : 1.3-1.4

Open Time at 20°C (min.) : 25-30

Adjustement time 25°C (min.) : 25-30

Pot life at 21°C (Hours) : 180-240

Bedding (mm.) : 1.5-8

Sag Test (mm.) : Nil

Open time bonding after 20 min

at 28 days (MPa) : >0.5

SPECIFICATIONS

EvaluationAdhesion Test

Adhesion strength (MPa)

Tensile adhesion strength after water immersion (MPa)

Tensile adhesion strength after heat aging (MPa)

>1

>1

>1

2 |

094 551 5458 02 651 8003 parexgroup.co.th e-learning VDO

*The information provided in this document results from our knowledge of the products and our experience. On-site results may vary, in particular according to the product application methods adopted. Where application methods not representative test before using the products. The above-mentioned information in no way constitutes a warranty relative to the use of the products. Our general terms and conditions of sale shall prevail, in any event, on the information provided in this document. Prior to application, customers and users are requested to check that they have the lasted version of this document.

ParexGroup Company Limited. 183 Regent House Building, Rajdamri Road., Lumpini, Bangkok 10330

| ENGLISH VERSION 10/60