Thioflex 600wP7E.pdf
-
Upload
ajitpushpa -
Category
Documents
-
view
126 -
download
16
Transcript of Thioflex 600wP7E.pdf
-
Tadmur Trading WLL _____________________________________________________________________
Post Box 37493, Doha Qatar Telephone: Fax: Email: (+974) 44337000 (+974) 44337100 bm.fosroc@tadmur-trading .com
Technical Submittal
Al Gurg Fosroc LLC P.O. Box 657, Dubai, U.A.E. Tel : +971 4 2039560, Fax : +971 4 2852023 / +971 4 2850406 www.fosroc.com
FOSROC THIOFLEX 600 with Primer 7E
-
CONTENTS
Section 1 Technical Data Sheet
Section 2 Method Statement
Section 3 Material Safety Data Sheet
Section 4 Test Reports
Section 5 Approvals
-
TECHNICAL DATA SHEET
-
Thio
flex
600
constructive solutionsFosroc Thioflex 600
Multi-component, gun and pouring grade, polysulphidesealant
Uses
Sealing movement joints in building and civil engineeringstructures, including superstructures, reservoirs, floors,basements and subways.
Advantages
! A high quality product meeting key international standards
! Forms a tough, elastic rubber-like seal
! Acts as an acoustic sealant
! Accommodates continuous and cyclic movement
! Excellent adhesion to most common substrates
! High resistance to ageing reduces physical damage dueto climatic extremes
Standards compliance
! British Standard BS 4254: 1983.! British Standard BS 6920: 1988 (gun grade grey).! U.S. Federal Specification TT-S-00227E November 1969
(amended 1970).! Water Byelaws Scheme Approved Product.! DTp specification for Highway Works Dec 1991 series
1000 clause 1017.! ASTM C 920-87, Type M, Class 25.
Description
Thioflex 600 is a multi-component joint sealant, based on aliquid polysulphide polymer, which when mixed and applied,cures to form a tough, rubber-like seal. The cured sealantexhibits excellent adhesion to most surfaces includingprimed concrete, glass, aluminium and stainless steel.
Thioflex 600 is available in gun and pouring grades. The gungrade is ideal for general application. It is packed in ready tomix, 2.5 litre & 4 litre tins containing the base and curingagent in the correct proportions. The pouring grade for jointsin horizontal surfaces is supplied in 4 litre & 5 litre packs withthe base and curing agent in separate tins. Both these gradesare available in Grey colour only.
For coloured sealants, Fosroc recommends the use ofNitoseal MS300*, a single component high performance silylterminated polyether sealant, available in white, grey, black,portland, rustic red and brown.
Thioflex 600 is particularly recommended for use in high risebuildings and other applications where access forsubsequent maintenance will be difficult and the risk of earlymovement failure must be minimised. It is also suitable forsealing joints in brickwork, retaining walls, reservoirs,basements and subways.Thioflex 600 pouring grade isrecommended for sealing expansion joints and stress reliefjoints in floors or other horizontal surfaces.
Specification
Joints shall be sealed using Fosroc Thioflex 600, two part,polysulphide sealant, manufactured by Fosroc to BS 42541983, and ASTM C 920 -87. Joints shall be prepared and thesealant mixed and applied in accordance with themanufacturers current data sheet.
Design criteria
Thioflex 600 may be applied to joints between 5 and 50 mmwide. Joints which are expected to experience cyclicmovements should be designed to an optimum width:depthratio of 2:1, subject to the overriding recommended minimumsealant depths set out below:
5 mm for metals, glass and other non-porous surfaces;
10 mm for all porous surfaces;
20 mm for trafficked joints and those subject to hydrostaticpressures.
To ensure that the sealant remains within its stated movementcapacity (25% MAF), sealing slot widths should be designedin accordance with the recommendations of BS 6093.
The use of a surface primer is always required on poroussurfaces. On non-porous surfaces a primer is not normallyrequired except where glass or glazed surfaces are to bepermanently immersed in water.
Example of a sealed movement joint in brickwork/blockworkis shown below1 Thioflex 600*
2 Hydrocell XL*
3 Brickwork4 D.P.C.5 Blockwork
-
Thioflex 600 - Page 2 of 4
Fosroc Thioflex 600
Chemical resistance tooccasional spillage :Dilute acids resistantDilute alkalis resistantPetrol resistantAviation fuels resistantDiesel fuel resistantKerosene resistantLubricating oils resistantSkydrol resistantWhite spirit resistantChlorinated solvents not resistantAromatic solvents not resistantDilute oxidising acids not resistant
Instructions for use
Joint preparation
The joint surfaces must be thoroughly dry, clean and frostfree. Remove all dust and laitance by rigorous wire brushing,grinding or grit blasting. Remove all rust, scale and protectivelacquers from metal surfaces. Remove any oil or grease withFosroc Joint Cleaner.
Any expansion joint filler must be checked to ensure it istightly packed and no gaps or voids exist at the base of thesealing slot before positioning a bond breaker.
Note: The use of a bond breaker is not required in expansionjoints containing Fosroc Hydrocell XL* or Expandafoam*
cellular polyethylene expansion joint fillers. For constructionor contraction joints a bond breaker tape or back-up stripshould be used. Where hydrostatic pressure exists, only bondbreaking tapes must be used, not foamed back-up strips.
Where a particularly neat finish is required, mask the faceedges of the joint before priming and remove immediatelyafter tooling is completed.
Priming
Non-porous surfaces
Use Primer 4 on glass, ceramics and metals. The one partchemically active clear liquid is to be applied by brush or pad.One thin coat should be applied and allowed to dry for 2 to 5minutes prior to sealant application.
Porous surfaces
Primer 7E: It is a two part high performance chemically activenon-toxic liquid for brush application to prime all concrete,stone, brickwork, timber and unglazed edges of ceramic tiles.Add component A of Primer 7E to component B and mixthroughly until a homogeneuos dispersion is achieved. Applyone thin coat using a clean, dry brush, ensuring complete
Example of a sealed subway expansion joint is shown below:
1 Thioflex 6002 Bond breaking tape3 Supercast Rearguard S waterstop4 Blinding concrete5 Membrane6 Bitucell*
Properties
Form : Grey colour, multi-part,paste compound
Movement accommodationfactor (BS 6093) : 25% butt joints
50% lap jointsPhysical orchemical change : Chemical curePot life : 2 hours @ 25C
1 hour @ 35CSetting time : 36 hours @ 15C
18 hours @ 25C12 hours @ 35C
Cure time : 2 weeks @ 15C1 week @ 25C4 days @ 35C
Application temperature : 5 to 50CHardness shore 'A' 25C : 15 to 23Water immersion : Thioflex 600 must be fully
cured before permanentimmersion in water.
Biological resistance : Thioflex 600 has beenevaluated inmicrobiologically activesituations and has beenshown to have resistance toaerobic conditions.
Solids content : 100%Density : 1.62 to 1.73 kg/litre
according to colour.Flash point : Over 65CFlammability : Burns but does not readily
support combustion.
-
Thioflex 600 - Page 3 of 4
Fosroc Thioflex 600
- Thioflex 600 should not be used in direct contact withmaterials containing pitch or bitumen.
- Only Thioflex 600 Gun Grade should be used in vertical orhorizontal joints in reservoirs or other water retainingstructures.
- Thioflex 600 is not recommended for use in highlychlorinated water. If in doubt, contact your local Fosroctechnical services department.
Estimating
SupplyThioflex 600 GG : 2.5 litre & 4 litre packsThioflex 600 PG : 4 litre & 5 litre packsPrimer 4 : 1 litre cansPrimer 7E : 500 ml cansFosroc solvent 102 : 5 litre containers
CoveragePrimer 4 : 60 m2/litrePrimer 7E : 8-10 m2/litre
Note: Coverege figures given are theoretical due to wastagefactors and the variety amd the nature of substrates,practical coverage figures maybe reduced, this willvary with site and application conditions.
Guide to sealant quantitiesJoint Litres Metre run Metre run Metre runsize per per per perin mm Metre run 2.5 ltr pack 4ltr pack 5 ltr pack5 x 5 0.025 100.00 160.00 200.005 x 10 0.050 50.00 80.00 100.0010 x 5 0.050 50.00 80.00 100.0010 x 10 0.100 25.00 40.00 50.0020 x 10 0.200 12.50 20.00 25.0020 x 15 0.300 8.30 13.30 16.6020 x 20 0.400 6.20 10.00 12.5040 x 20 0.800 3.10 5.00 6.2040 x 25 1.000 2.50 4.00 5.0040 x 30 1.200 2.00 3.30 4.1040 x 40 1.600 1.50 2.50 3.1050 x 25 1.250 2.00 3.20 4.0050 x 30 1.500 1.60 2.64 3.3050 x 40 2.000 1.25 2.00 2.5050 x 50 2.500 1.00 1.60 2.00
1 litre of Primer 4 to 1500m length of 10 x 20mm joint.
1.5 litre of Primer 7E to 150m length of 10 x 20mm joint.
These are theoretical yields. No allowance has been madefor variation in joint width or wastage.
coverage. Avoid over priming resulting in an excess of primerin the base of the joint or application beyond faces. The mixedThioflex 600 must be applied when the primer is tack free, thatis after the evaporation of the solvent but before the primer filmhas completely reacted. After 6 hours @ 20oC, or 3 hours @35oC the surfaces must be re-primed before applying thesealant.
Steel surfaces
Iron and steel must be protected with an anti-corrosion primerprior to sealing.
Mixing
Gun Grade
The base component and curing agent are supplied ready formixing in a single tin. Mix thoroughly using a slow speed drill(300-500 rpm) fitted with a Fosroc Mixing Paddle (MR2) for5 minutes. Only thorough mixing, including material right atthe bottom of the tin, will result in proper curing. In cold weatherThioflex 600 mixes more easily if stored overnight at roomtemperature.
Immediately after mixing, load the sealant into a Fosroc GGun using the follower plate, and apply to the joint.
Pouring Grade
Thioflex 600 Pouring Grade is supplied in two separatecontainers. The small container contents should be transferredto the other tin, and mixed as per the gun grade instructions.The pouring grade may be poured directly into horizontal jointsor for application to horizontal joints less than 15 mm wideloaded into a Fosroc G Gun. For quantity application, a Fosroc1.5 litre gun is available.
Finishing
Thioflex 600 should be tooled to a smooth finish. A minimumof surface lubricant such as dilute detergent solution may beused to assist the process. Any masking tape should beremoved immediately after tooling.
Cleaning
Clean equipment immediately after use with Fosroc Solvent 102.
Limitations
- Over-painting of sealants is not recommended becauseof the inability of paint films to accept movement. However,if required, trials should be carried out to determinecompatibility.
-
UAE/0300/08/F
Fosroc Thioflex 600
Al Gurg Fosroc LLCPost Box 657, DubaiUnited Arab Emirates
www.fosroc.com
Important noteFosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions forthe Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the users responsibility toobtain the recent version.
Head Officetelephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]
Regional officesAbu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected], YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected], Boodai telephone: 4817618 fax: 4832124 email: [email protected], Al Amana telephone: 24815080 fax: 24817554 email: [email protected], Tadmur telephone: 4432365 fax: 4419517 email: [email protected]
* Denotes the trademark of Fosroc International Limited
See separate data sheet
Storage
Thioflex 600 and Primer 7E have a storage life of 12 monthsand Primer 4 has a storage life of 6 months when kept inoriginal containers and stored in dry conditions between5C and 27C.
Precautions
Health and safety
Thioflex 600, Primer 4 and Primer 7E should not come incontact with skin and eyes or be swallowed. Avoid breathingof vapour. Splashes must be washed off immediately. Wearimpervious rubber or PVC gloves and eye protection. Handsshould be thoroughly washed with soap and water beforeeating or smoking. In the case of eye contact seek medicalattention immediately.
Thioflex 600 curing agent consists of a heavy metal basedoxide. Cured sealant should not be burned off due to thegeneration of toxic fumes. Empty containers must becollected for careful disposal and not left lying about.
Fire
Fosroc Solvent 102 is flammable. Primer 4 and primer 7Eare highly flammable, store away from heat. Do not usenear naked flames or other sources of ignition. No smoking.Use in well ventilated surroundings. In the event of fire,extinguish with CO2 foam.
Flash pointPrimer 4 : 10CPrimer 7E : 23C
For further information, refer to the Product Material SafetyData Sheet.
Additional Information
Fosroc manufactures a wide range of complementaryproducts which include :
! waterproofing membranes & waterstops
! joint sealants & filler boards
! cementitious & epoxy grouts
! specialised flooring materials
Fosroc additionally offers a comprehensive package ofproducts specifically designed for the repair andrefurbishment of damaged concrete. Fosrocs SystematicApproach to concrete repair features the following :
! hand-placed repair mortars
! spray grade repair mortars
! fluid micro-concretes
! chemically resistant epoxy mortars
! anti-carbonation/anti-chloride protective coatings
! chemical and abrasion resistant coatings
For further information on any of the above, please consultyour local Fosroc office - as below.
-
Al Gurg Fosroc LLC
Post Box 657, Dubai
United Arab Emirates
www.fosroc.com
telephone: fax: email:
(+9714) 2039699 (+9714) 2859649 [email protected]
Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai
Page 1
Fosroc Primer 7E
UAE/0682/10/A
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control
over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or
not in accordance with any advice, specification, recommendation or information given by it.
Constructive solutions
Two-part primer for Polysulphide sealant.
Description
Primer 7E is a two part high performance chemically active, non-toxic liquid for brush application to prime all concrete, stone, brickwork, timber and unglazed edges of ceramic tiles.
Advantages
Easy to Apply
Strong adhesion Application
Empty the entire contents of the hardener tin into the base tin, replace base tin lid. Mix thoroughly until a homogeneous dispersion is achieved. Apply one thin coat using a clean dry brush. Avoid over application of primer causing puddles in the bottom of the joint. Sealants should be applied between 30 minutes and 4 hours after priming when its tack free.
Cleaning
Clean equipment immediately after use with Fosroc Solvent 102.
Estimating
Supply
Primer 7E: 500 ml can
Coverage
Primer 7E:
8 -10 m2 / ltr
Storage
Shelf life
12 months if stored in the original unopened packs in a cool dry place. Do not store in direct sunlight.
Precautions
Health and safety
Primer 7E highly flammable liquid. Shall be stored away from heat. and shall not be used near a naked flame. Skin contact shall be avoided. Eye protection and impervious rubber or PVC gloves shall be worn. Splashes must be washed off immediately. Prolonged breathing of vapour shall be avoided. Hands shall be washed thoroughly before eating or smoking. In the case of eye contact, medical attention shall be sought immediately.
Disposal
Dispose according to local authority regulations. Do not dispose down drains or into local waterways. For further information on any of the above, please consult your local Fosroc office - as below.
Additional information
Primer 7E
Flash point: 23oC
Storage life: 12 months
Drying time: 20 to 60 mins.
Flash point - Fosroc Solvent 102: 33oC
For further info please contact your local Fosroc office.
-
METHOD STATEMENT
-
telephone: fax: email: (+9714) 2039699 (+9714) 2859649 [email protected] Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai
Al Gurg Fosroc LLC Post Box 657, Dubai United Arab Emirates www.fosroc.com
constructive solutions method statement
Thioflex 600 Section A : General Comments Comments High temperature working It is suggested that, for temperatures above 350C, the following guidelines are adopted as
good working practice: (i) Store unmixed materials in a cool (preferably temperature controlled) environment, avoiding
exposure to direct sunlight. (ii) Keep equipment cool, arranging shade protection if necessary. It is especially important to
keep cool those surfaces of the equipment which will come into direct contact with the material itself.
(iii) Try to avoid application during the hottest times of the day, arrange temporary shading as necessary.
(iv) Make sufficient material, plant and labour available to ensure that application is a continuous process.
Equipment It is suggested that the following list of equipment is adopted as a minimum requirement Protective clothing : Protective overalls
: Good quality gloves, goggles and face mask
Preparation equipment : Proprietary blasting equipment Fosroc Joint Cleaner Mixing equipment : 1 KW slow speed drill, 400 or 500 rpm, plus Fosroc Mixing Paddle MR2 Application equipment : Brush
Fosroc Barrel Gun
Joint shaping tool
Application - points of note
Fosroc operates a policy to encourage the use, where possible, of approved or licensed applicators. This ensures that repairs are completed satisfactorily so that the long term performance of the materials is assured. For contractors who wish to apply the materials themselves Fosroc is also able to offer technical assistance and training, either on-site or at its Training Centre in Dubai.
-
constructive solutions
Section B : Application Method
1.0 Joint Preparation
Refer to the Joint width/depth ratio as per manufacturers instructions in the technical data sheet.
1.1 The substrate to which Thioflex 600 is bonded must be clean, dry and sound. All arris repairs should be effected using a Fosroc repair compound.
1.2 Remove all dirt, surface laitence, residual joint former or other contamination from joint faces by power wire brushing, grinding or grit-blasting. Ensure usage of dry, oil-free compressed air for blowing all joints. Oil or grease can be removed using Fosroc Joint cleaner.
1.3 All expansion joints must be filled with fillers; tightly packed with no gaps or voids existing at the base of the sealing slot.
1.4 For construction or contraction joints, a bond breaker or back up tape is recommended, but in joints where hydrostatic pressure exists, only bond breaking tapes must be used.
2.0 Mixing
2.1 Gun Grade
2.1.1 The two components of Thioflex 600, supplied in correct mixing proportions, must be thoroughly mixed for atleast 2 minutes using the recommended Fosroc MR2 mixing paddle fitted to a slow speed electric drill.
2.1.2 Ensure that the inside of the tin is scraped with a flat bladed tool so that there is no component on the sides left unmixed.
2.1.3 Mixing should be continued for a further three minutes. The total mixing time is 5 minutes.
2.2 Pouring Grade
2.2.1 The two components of Thioflex 600, supplied in correct mixing proportions, must be thoroughly mixed for 5 minutes.
2.2.2 Ensure proper mixing of the material right at the bottom of the tin, as it will effect the curing otherwise.
Page 2 of 4
-
constructive solutions
3.0 Priming
3.1 Non-Porous Substrate
3.1.1 The substrate to which Thioflex 600 is bonded must be primed with Primer 4.
3.1.2 Apply the primer onto the surface using a brush and leave to dry for 2 to 5 minutes prior to sealant application.
3.2 Porous Substrates
3.2.1 The substrate must be primed with Primer 7E; a two component.
3.2.2 Add component A of Primer 7E to component B and mix thoroughly until a homogeneous dispersion is achieved.
3.2.2 Apply one thin coat of Primer7E onto the surface using a clean, dry brush, ensuring complete coverage.
3.2.3 The mixed Thioflex 600 must be applied when the primer is tack free.
3.2.4 Ensure application of Thioflex 600 within 6 hours @ 20C, or 3 hours @ 35C. Re-priming is necessary if application is delayed.
4.0 Application
Thioflex 600 must not be used in direct contact with materials containing pitch or bitumen.
4.1 After completion of mixing of the two components, place the single hole follower plate over the Thioflex and fill directly into a Fosroc Barrel Gun.
4.2 Gun Thioflex 600 firmly into the joint to ensure complete wetting of the bonding surfaces.
4.3 The pouring grade may be poured directly into horizontal joints. For application to horizontal joints less than 15mm wide, load the Thioflex 600 into a Fosroc G Gun. For quantity application, a fosroc 1.5litre gun is available.
4.4 Compress and smooth the sealant with a joint shaping tool wetted with a dilute detergent solution.
4.5 Upon smoothening of the sealant, immediately strip off any masking tape.
Page 3 of 4
-
Page 4 of 4
constructive solutions
5.0 Cleaning
5.1 Clean all equipment immediately after use with Fosroc Solvent 102.
Section C : Approval and variations
This method statement is offered by Fosroc as a standard proposal for the application of Thioflex 600. It remains the responsibility of the Engineer to determine the correct method for any given application.
Where alternative methods are to be used, these must be submitted to Fosroc for approval, in writing, prior to commencement of any work. Fosroc will not accept responsibility or liability for variations to the above method statement under any other condition.
-
MATERIAL SAFETY DATASHEET
-
SAFETY DATA SHEET
THIOFLEX 600 - GUN GRADE
1 IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
PRODUCT NAME THIOFLEX 600 - GUN GRADE
APPLICATION Joint sealant
Fosroc LimitedSUPPLIER
Drayton Manor Business Park
Coleshill Road
Tamworth
Staffs
B78 3TL
Tel: 01827 262222
Fax: 01827 262444
2 HAZARDS IDENTIFICATION
May cause sensitisation by skin contact. Very toxic to aquatic organisms.
CLASSIFICATION R43. N;R50.
3 COMPOSITION/INFORMATION ON INGREDIENTS
EC No.Name ClassificationCAS-No. Content
287-476-5C10-C13 CHLORINATED PARAFFIN N;R50. R53.085535-84-8 10-30%
EPOXY RESIN (AVERAGE MOLECULAR WEIGHT
-
THIOFLEX 600 - GUN GRADE
PERSONAL PRECAUTIONS
Wear suitable protective clothing, gloves and eye/face protection.
ENVIRONMENTAL PRECAUTIONS
Prevent entry into drains, sewers and water courses.
SPILL CLEAN UP METHODS
Soak up with inert absorbent or contain and remove by best available means. Dispose of as waste.
7 HANDLING AND STORAGE
USAGE PRECAUTIONS
Avoid skin and eye contact. Do not eat, drink or smoke whilst using the product. Wash hands thoroughly after handling this product.
STORAGE PRECAUTIONS
Store between ('C) 5 and 30. Store out of direct sunlight. Kep away from foodstuffs and food containers.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Std ST - ppmLT - ppm LT - mg/m3 ST - mg/m3Name
50 ppm(Sk) 220 mg/m3(Sk)WEL 100 ppm(Sk) 441 mg/m3(Sk)XYLENE
9 PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE Semi-solid (muti-layer paste)
COLOUR Pigmented
ODOUR Mercaptan odour
SOLUBILITY Insoluble
RELATIVE DENSITY 1.6 - 1.7 (depending on colour) VAPOUR DENSITY (air=1) Not determined
FLASH POINT (C) > 100
10 STABILITY AND REACTIVITY
STABILITY
Hazardous polymerisation will not occur.
CONDITIONS TO AVOID
Temperatures ('C) above 50.
MATERIALS TO AVOID
Strong oxidising agents. Strong acids.
HAZARDOUS DECOMPOSITION PRODUCTS
Thermal decomposition:- Irritant fumes. Chlorine compounds including hydrogen chloride. Carbon monoxide.
11 TOXICOLOGICAL INFORMATION
INHALATION
Irritating to respiratory system.
INGESTION
Harmful if swallowed. May cause nausea, vomiting and diarrhoea.
SKIN CONTACT
Mildly irritating.
EYE CONTACT
Causes transient irritation.
12 ECOLOGICAL INFORMATION
ECOTOXICITY
Not ecotoxic to fish/daphnia/algae in cured state.
MOBILITY
Insoluble in water.
42 /
-
THIOFLEX 600 - GUN GRADE
BIOACCUMULATION
Not known.
DEGRADABILITY
Expected to be not readily biodegradable.
13 DISPOSAL CONSIDERATIONS
GENERAL INFORMATION
Disposal must be in accordance with local and national legislation.
DISPOSAL METHODS
Classified as a special waste. Dispose of through an authorised waste contractor to a licensed site.
14 TRANSPORT INFORMATION
PROPER SHIPPING NAME Environmentally hazardous substance, solid, NOS (Chlorinated Paraffin C10-13)
3077UN NO. ROAD 9ADR CLASS NO.
IIIADR PACK GROUP 9IMDG CLASS
IIIIMDG PACK GR. MARINE POLLUTANT
9AIR CLASS
15 REGULATORY INFORMATION
LABELLING
Irritant Dangerous for the
environment
CONTAINS EPOXY RESIN (AVERAGE MOLECULAR WEIGHT
-
THIOFLEX 600 - GUN GRADE
GENERAL INFORMATION
The data and advice given when the product is used for the stated application or applications. The product is not sold as suitable for any
other application. Use of the product for applications other than as stated in this sheet may give rise to risks not mentioned on this sheet.
The product should not be used for other than the stated application or applications without seeking advise from Fosroc Ltd. If this product
has been purchased for supply to a third party for use at work., it is the purchaser's duty to take all the necessary steps to secure that any
person handling or using the product is provided with the information in this sheet. It is the responsibility and duty of the employer to inform
employees and others who may be affected of any hazards described in this sheet and of any precautions which should be taken. This
sheet does not constitute or substitute for the users own assessment of workshop risk, as required by other health and safety legislation.
Further copies of this Safety Data Sheet may be obtained from Fosroc Limited.
DATE 08.07.08
RISK PHRASES IN FULL
Flammable.R10
Harmful by inhalation and in contact with skin.R20/21
Harmful by inhalation and if swallowed.R20/22
Irritating to eyes and respiratory system.R36/37
Irritating to eyes and skin.R36/38
Irritating to skin.R38
Limited evidence of a carcinogenic effect.R40
May cause sensitisation by skin contact.R43
Very toxic to aquatic organisms.R50
Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.R51/53
May cause long-term adverse effects in the aquatic environment.R53
44 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 1
SAFETY DATA SHEET
PRIMER 7E BASE
1 IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
PRODUCT NAME PRIMER 7E BASE
PRODUCT NO. M2100000AEDXB1
AL GURG FOSROC LLCSUPPLIER
PO BOX 657
Al Hamer Road
Al Ramool Industrial Estate
Dubai
UAE
+97142858606
EMERGENCY TELEPHONE +97142039699 (08:00 to 16:30) // +971506258232 (16:30 to 08:00)GMT+4
MANUFACTURER Al Gurg Fosroc LLC, Al Ramool Industrial Estate, Dubai , UAE.
2 HAZARDS IDENTIFICATION
Flammable. Harmful by inhalation and in contact with skin. Irritating to eyes and skin. May cause sensitisation by skin contact.
CLASSIFICATION (1999/45) Xn;R20/21. Xi;R36/38. R43. R10.
ENVIRONMENT
The product contains a substance which is harmful to aquatic organisms and which may cause long term adverse effects in the aquatic
environment.
PHYSICAL AND CHEMICAL HAZARDS
The product is flammable, and heating may generate vapours which may form explosive vapour/air mixtures.
HUMAN HEALTH
In high concentrations, vapours and spray mists are narcotic and may cause headache, fatigue, dizziness and nausea. Harmful by
inhalation and in contact with skin. The product is irritating to eyes and skin.
3 COMPOSITION/INFORMATION ON INGREDIENTS
EC No.Name Classification (67/548)CAS-No. Content %
PHENOL, 4,4'-
(1-METHYLETHYLIDENE)BIS-POLYMER WITH
2,2'-(1-METHYLETHYLIDENE)BIS(4,1-PHENYLENE
OXYMETHYLENE)BIS(OXIRANE)
Xi;R36,R38. R43.25036-25-3 30-60%
203-539-11-METHOXY-2-PROPANOL R10 R67107-98-2 30-60%
215-535-7XYLENE R10 Xn;R20/21 Xi;R381330-20-7 10-30%
The Full Text for all R-Phrases are Displayed in Section 16
COMPOSITION COMMENTS
The data shown are in accordance with the latest EC Directives.
4 FIRST-AID MEASURES
GENERAL INFORMATION
General first aid, rest, warmth and fresh air. Do not give victim anything to drink if they are unconscious. Get medical attention if any
discomfort continues.
51 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 1
PRIMER 7E BASE
INHALATION
Place unconscious person on the side in the recovery position and ensure breathing If respiratory problems, artificial respiration/oxygen.
Get medical attention if any discomfort continues.
INGESTION
Immediately rinse mouth and drink plenty of water or milk. Keep person under observation. Do not induce vomiting. If vomiting occurs, keep
head low. Transport immediately to hospital and bring along these instructions.
SKIN CONTACT
Immediately remove contaminated clothing. Wash off promptly and flush contaminated skin with water. Promptly remove clothing if soaked
through and flush skin with water.
EYE CONTACT
Make sure to remove any contact lenses from the eyes before rinsing. Promptly wash eyes with plenty of water while lifting the eye lids.
Get medical attention promptly if symptoms occur after washing.
5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Fire can be extinguished using: Water spray, fog or mist. Foam, carbon dioxide or dry powder. Dry chemicals, sand, dolomite etc.
SPECIAL FIRE FIGHTING PROCEDURES
Use pressurised air mask if product is involved in a fire. Cool containers exposed to flames with water until well after the fire is out.
UNUSUAL FIRE & EXPLOSION HAZARDS
Fire causes formation of toxic gases.
PROTECTIVE MEASURES IN FIRE
Self contained breathing apparatus and full protective clothing must be worn in case of fire.
6 ACCIDENTAL RELEASE MEASURES
PERSONAL PRECAUTIONS
Wear protective clothing as described in Section 8 of this safety data sheet.
ENVIRONMENTAL PRECAUTIONS
Spillages or uncontrolled discharges into watercourses must be IMMEDIATELY alerted to the Environmental Agency or other appropriate
regulatory body.
SPILL CLEAN UP METHODS
Keep combustibles away from spilled material. Extinguish all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate. Absorb
in vermiculite, dry sand or earth and place into containers. Wash thoroughly after dealing with a spillage.
7 HANDLING AND STORAGE
USAGE PRECAUTIONS
Keep away from heat, sparks and open flame. Avoid spilling, skin and eye contact. Ventilate well, avoid breathing vapours. Use
approved respirator if air contamination is above accepted level.
STORAGE PRECAUTIONS
Flammable/combustible - Keep away from oxidisers, heat and flames. Store in tightly closed original container in a dry, cool and
well-ventilated place. Keep in original container. Avoid contact with oxidising agents.
STORAGE CLASS
Flammable liquid storage.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
STD STEL - 15 MinTWA - 8 HrsName Notes
100 ppm 375 mg/m3WEL 150 ppm 560 mg/m31-METHOXY-2-PROPANOL Sk
50 ppm 220 mg/m3WEL 100 ppm 441 mg/m3XYLENE Sk
WEL = Workplace Exposure Limit.
Sk = Can be absorbed through skin.
52 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 1
PRIMER 7E BASE
INGREDIENT COMMENTS
WEL = Workplace Exposure Limits
PROTECTIVE EQUIPMENT
PROCESS CONDITIONS
Provide eyewash station.
ENGINEERING MEASURES
Provide adequate ventilation, including appropriate local extraction, to ensure that the defined occupational exposure limit is not exceeded.
All handling to take place in well-ventilated area.
RESPIRATORY EQUIPMENT
Wear mask supplied with:
Gas cartridge suitable for organic substances.
HAND PROTECTION
Use protective gloves made of: Neoprene. Nitrile. Rubber (natural, latex).
EYE PROTECTION
Wear splash-proof eye goggles to prevent any possibility of eye contact.
OTHER PROTECTION
Wear appropriate clothing to prevent any possibility of skin contact.
HYGIENE MEASURES
DO NOT SMOKE IN WORK AREA! Wash at the end of each work shift and before eating, smoking and using the toilet. Promptly remove
any clothing that becomes contaminated. Use appropriate skin cream to prevent drying of skin. When using do not eat, drink or smoke.
9 PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE Liquid
COLOUR Straw
ODOUR Aromatic.
BOILING POINT (C) 135-150
RELATIVE DENSITY 1.3-1.4 20 deg C
FLASH POINT (C) 23 deg C
AUTO IGNITION
TEMPERATURE (C)
300
10 STABILITY AND REACTIVITY
STABILITY
No particular stability concerns.
CONDITIONS TO AVOID
Avoid heat, flames and other sources of ignition. Avoid contact with strong oxidisers.
HAZARDOUS DECOMPOSITION PRODUCTS
Thermal decomposition or combustion may liberate carbon oxides and other toxic gases or vapours.
11 TOXICOLOGICAL INFORMATION
GENERAL INFORMATION
Prolonged and repeated contact with solvents over a long period may lead to permanent health problems.
INHALATION
In high concentrations, vapours may irritate throat and respiratory system and cause coughing. Harmful by inhalation.
INGESTION
Gastrointestinal symptoms, including upset stomach.
53 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 1
PRIMER 7E BASE
SKIN CONTACT
Acts as a defatting agent on skin. May cause cracking of skin, and eczema. Irritating to skin. Harmful in contact with skin. May cause
sensitisation by skin contact.
EYE CONTACT
Irritating and may cause redness and pain.
12 ECOLOGICAL INFORMATION
ECOTOXICITY
Harmful to aquatic organisms, may cause long term adverse effects in the aquatic environment
13 DISPOSAL CONSIDERATIONS
GENERAL INFORMATION
Waste to be treated as controlled waste. Disposal to licensed waste disposal site in accordance with local Waste Disposal Authority.
DISPOSAL METHODS
Dispose of waste and residues in accordance with local authority requirements. Make sure containers are empty before discarding
(explosion risk). Absorb in vermiculite or dry sand and dispose of at a licenced hazardous waste collection point.
14 TRANSPORT INFORMATION
PROPER SHIPPING NAME FLAMMABLE LIQUID, N.O.S. (1-METHOXY-2-PROPANOL, XYLENE)
No.ENVIRONMENTALLY
HAZARDOUS
SUBSTANCE/MARINE
POLLUTANT
1993UN NO. ROAD
3ADR CLASS NO.
Class 3: Flammable liquids.ADR CLASS
IIIADR PACK GROUP
(D/E)TUNNEL RESTRICTION CODE
30HAZARD No. (ADR)
3ADR LABEL NO.
3YEHAZCHEM CODE
1993UN NO. SEA
3IMDG CLASS
IIIIMDG PACK GR.
F-E, S-EEMS
1993UN NO. AIR
3AIR CLASS
IIIAIR PACK GR.
15 REGULATORY INFORMATION
LABELLING
54 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 1
PRIMER 7E BASE
Harmful
CONTAINS PHENOL, 4,4'-(1-METHYLETHYLIDENE)BIS-POLYMER WITH 2,2'-
(1-METHYLETHYLIDENE)BIS(4,1-PHENYLENE OXYMETHYLENE)BIS(OXIRANE)
XYLENE
RISK PHRASES
R10 Flammable.
R20/21 Harmful by inhalation and in contact with skin.
R36/38 Irritating to eyes and skin.
R43 May cause sensitisation by skin contact.
SAFETY PHRASES
S25 Avoid contact with eyes.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical
advice.
S36/37 Wear suitable protective clothing and gloves.
S51 Use only in well-ventilated areas.
S60 This material and its container must be disposed of as hazardous waste.
NATIONAL REGULATIONS
The Chemicals (Hazard Information and Packaging for Supply) Regulations 2002. No. 1689. Workplace Exposure Limits 2005 (EH40)
16 OTHER INFORMATION
GENERAL INFORMATION
The user must be instructed in the proper work procedure and be familiar with the contents of these instructions.
REVISION DATE 25/07/2010
REV. NO./REPL. SDS GENERATED 1
RISK PHRASES IN FULL
Flammable.R10
Harmful by inhalation and in contact with skin.R20/21
Irritating to eyes.R36
Irritating to skin.R38
May cause sensitisation by skin contact.R43
Vapours may cause drowsiness and dizziness.R67
DISCLAIMER
The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in
accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using
the product in combination with any other product or any other process is the responsibility of the user.
55 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 3
SAFETY DATA SHEET
PRIMER 7E HARDENER
1 IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
PRODUCT NAME PRIMER 7E HARDENER
PRODUCT NO. M2100002AEDXB1
AL GURG FOSROC LLCSUPPLIER
PO BOX 657
Al Hamer Road
Al Ramool Industrial Estate
Dubai
UAE
+97142858606
EMERGENCY TELEPHONE +97142039699 (08:00 to 16:30) // +971506258232 (16:30 to 08:00)GMT+4
MANUFACTURER Al Gurg Fosroc LLC, Al Ramool Industrial Estate, Dubai , UAE.
2 HAZARDS IDENTIFICATION
Flammable. Vapours may cause drowsiness and dizziness. Irritating to skin. Risk of serious damage to eyes. Harmful to aquatic organisms,
may cause long-term adverse effects in the aquatic environment.
CLASSIFICATION (1999/45) Xi;R38, R41. R10, R52/53, R67.
ENVIRONMENT
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
PHYSICAL AND CHEMICAL HAZARDS
The product is flammable, and heating may generate vapours which may form explosive vapour/air mixtures.
HUMAN HEALTH
In high concentrations, vapours and spray mists are narcotic and may cause headache, fatigue, dizziness and nausea. Risk of serious
damage to eyes. Vapours/aerosol spray may irritate the respiratory system.
3 COMPOSITION/INFORMATION ON INGREDIENTS
EC No.Name Classification (67/548)CAS-No. Content %
203-539-11-METHOXY-2-PROPANOL R10 R67107-98-2 30-60%
215-535-7XYLENE R10 Xn;R20/21 Xi;R381330-20-7 10-30%
201-148-0ISO-BUTANOL R10 Xi;R37/38,R41 R6778-83-1 10-30%
LIQUID POLYSULPHIDE POLYMER -68611-50-7 1-5%
The Full Text for all R-Phrases are Displayed in Section 16
COMPOSITION COMMENTS
The data shown are in accordance with the latest EC Directives.
4 FIRST-AID MEASURES
GENERAL INFORMATION
General first aid, rest, warmth and fresh air. Do not give victim anything to drink if they are unconscious. Get medical attention if any
discomfort continues.
51 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 3
PRIMER 7E HARDENER
INHALATION
Place unconscious person on the side in the recovery position and ensure breathing If respiratory problems, artificial respiration/oxygen.
Get medical attention if any discomfort continues.
INGESTION
Immediately rinse mouth and drink plenty of water or milk. Keep person under observation. Do not induce vomiting. If vomiting occurs, keep
head low. Transport immediately to hospital and bring along these instructions.
SKIN CONTACT
Immediately remove contaminated clothing. Wash off promptly and flush contaminated skin with water. Promptly remove clothing if soaked
through and flush skin with water.
EYE CONTACT
Make sure to remove any contact lenses from the eyes before rinsing. Promptly wash eyes with plenty of water while lifting the eye lids.
Get medical attention promptly if symptoms occur after washing.
5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Fire can be extinguished using: Water spray, fog or mist. Foam, carbon dioxide or dry powder. Dry chemicals, sand, dolomite etc.
SPECIAL FIRE FIGHTING PROCEDURES
Use pressurised air mask if product is involved in a fire. Cool containers exposed to flames with water until well after the fire is out. Keep
run-off water out of sewers and water sources. Dike for water control.
UNUSUAL FIRE & EXPLOSION HAZARDS
Fire causes formation of toxic gases.
PROTECTIVE MEASURES IN FIRE
Self contained breathing apparatus and full protective clothing must be worn in case of fire.
6 ACCIDENTAL RELEASE MEASURES
PERSONAL PRECAUTIONS
Wear protective clothing as described in Section 8 of this safety data sheet.
ENVIRONMENTAL PRECAUTIONS
Spillages or uncontrolled discharges into watercourses must be IMMEDIATELY alerted to the Environmental Agency or other appropriate
regulatory body.
SPILL CLEAN UP METHODS
Keep combustibles away from spilled material. Extinguish all ignition sources. Avoid sparks, flames, heat and smoking. Ventilate. Absorb
in vermiculite, dry sand or earth and place into containers. Wash thoroughly after dealing with a spillage.
7 HANDLING AND STORAGE
USAGE PRECAUTIONS
Keep away from heat, sparks and open flame. Avoid spilling, skin and eye contact. Ventilate well, avoid breathing vapours. Use
approved respirator if air contamination is above accepted level.
STORAGE PRECAUTIONS
Flammable/combustible - Keep away from oxidisers, heat and flames. Store in tightly closed original container in a dry, cool and
well-ventilated place. Keep in original container. Avoid contact with oxidising agents.
STORAGE CLASS
Flammable liquid storage.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
STD STEL - 15 MinTWA - 8 HrsName Notes
100 ppm 375 mg/m3WEL 150 ppm 560 mg/m31-METHOXY-2-PROPANOL Sk
50 ppm 154 mg/m3WEL 75 ppm 231 mg/m3ISO-BUTANOL
50 ppm 220 mg/m3WEL 100 ppm 441 mg/m3XYLENE Sk
52 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 3
PRIMER 7E HARDENER
WEL = Workplace Exposure Limit.
Sk = Can be absorbed through skin.
INGREDIENT COMMENTS
WEL = Workplace Exposure Limits
PROTECTIVE EQUIPMENT
PROCESS CONDITIONS
Provide eyewash station.
ENGINEERING MEASURES
Provide adequate ventilation, including appropriate local extraction, to ensure that the defined occupational exposure limit is not exceeded.
All handling to take place in well-ventilated area.
RESPIRATORY EQUIPMENT
Wear mask supplied with:
Gas cartridge suitable for organic substances.
HAND PROTECTION
Use protective gloves made of: Neoprene. Nitrile. Rubber (natural, latex).
EYE PROTECTION
Wear splash-proof eye goggles to prevent any possibility of eye contact.
OTHER PROTECTION
Wear appropriate clothing to prevent any possibility of skin contact.
HYGIENE MEASURES
DO NOT SMOKE IN WORK AREA! Wash at the end of each work shift and before eating, smoking and using the toilet. Promptly remove
any clothing that becomes contaminated. Use appropriate skin cream to prevent drying of skin. When using do not eat, drink or smoke.
9 PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE Liquid
COLOUR Amber
ODOUR Aromatic.
SOLUBILITY Slightly soluble in water.
BOILING POINT (C) 116-130
RELATIVE DENSITY 0.96 20 deg C
FLASH POINT (C) 23 deg C
AUTO IGNITION
TEMPERATURE (C)
300
10 STABILITY AND REACTIVITY
STABILITY
No particular stability concerns.
CONDITIONS TO AVOID
Avoid heat, flames and other sources of ignition. Avoid contact with strong oxidisers.
HAZARDOUS DECOMPOSITION PRODUCTS
Thermal decomposition or combustion may liberate carbon oxides and other toxic gases or vapours.
11 TOXICOLOGICAL INFORMATION
GENERAL INFORMATION
Prolonged and repeated contact with solvents over a long period may lead to permanent health problems.
53 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 3
PRIMER 7E HARDENER
INHALATION
In high concentrations, vapours may irritate throat and respiratory system and cause coughing.
INGESTION
Gastrointestinal symptoms, including upset stomach.
SKIN CONTACT
Acts as a defatting agent on skin. May cause cracking of skin, and eczema. Irritating to skin.
EYE CONTACT
Risk of serious damage to eyes.
12 ECOLOGICAL INFORMATION
ECOTOXICITY
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
13 DISPOSAL CONSIDERATIONS
GENERAL INFORMATION
Waste to be treated as controlled waste. Disposal to licensed waste disposal site in accordance with local Waste Disposal Authority.
DISPOSAL METHODS
Dispose of waste and residues in accordance with local authority requirements. Make sure containers are empty before discarding
(explosion risk). Absorb in vermiculite or dry sand and dispose of at a licenced hazardous waste collection point.
14 TRANSPORT INFORMATION
PROPER SHIPPING NAME FLAMMABLE LIQUID, N.O.S. (1-METHOXY-2-PROPANOL, ISO-BUTANOL)
No.ENVIRONMENTALLY
HAZARDOUS
SUBSTANCE/MARINE
POLLUTANT
1993UN NO. ROAD
3ADR CLASS NO.
Class 3: Flammable liquids.ADR CLASS
IIIADR PACK GROUP
(D/E)TUNNEL RESTRICTION CODE
30HAZARD No. (ADR)
3ADR LABEL NO.
3YEHAZCHEM CODE
1993UN NO. SEA
3IMDG CLASS
IIIIMDG PACK GR.
F-E, S-EEMS
1993UN NO. AIR
3AIR CLASS
IIIAIR PACK GR.
15 REGULATORY INFORMATION
54 /
-
REVISION DATE 25/07/2010 REV. NO./REPL. SDS GENERATED 3
PRIMER 7E HARDENER
LABELLING
Irritant
RISK PHRASES
R10 Flammable.
R38 Irritating to skin.
R41 Risk of serious damage to eyes.
R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
R67 Vapours may cause drowsiness and dizziness.
SAFETY PHRASES
NC Not classified.
NATIONAL REGULATIONS
The Chemicals (Hazard Information and Packaging for Supply) Regulations 2002. No. 1689. Workplace Exposure Limits 2005 (EH40)
16 OTHER INFORMATION
GENERAL INFORMATION
The user must be instructed in the proper work procedure and be familiar with the contents of these instructions.
REVISION DATE 25/07/2010
REV. NO./REPL. SDS GENERATED 3
RISK PHRASES IN FULL
Flammable.R10
Harmful by inhalation and in contact with skin.R20/21
Irritating to respiratory system and skin.R37/38
Irritating to skin.R38
Risk of serious damage to eyes.R41
Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.R51/53
Vapours may cause drowsiness and dizziness.R67
DISCLAIMER
The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in
accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using
the product in combination with any other product or any other process is the responsibility of the user.
55 /
-
TEST REPORTS
-
APPROVALS
-
329-0
B6TH-40-K005-00329_00
-
Doha Petroleum Construction Co. Ltd.Post Box 1744 , Doha - Qatar , Tel: +974-44600350 , Fax: +974-44601066
web: www.dopet.com - email: [email protected]
DOCUMENT TRANSMITTALTransmittal No.:
23305/CVL/TN/0005Dopet Job Ref.:
23305Project No.:
3219Contract No.:GC11113800
ToCompanyName : DOPET CIVIL DEPARTMENTAddress :Attn. : Mr. Ibrahim Wafi Said - Head of Civil DepartmentCC :
* Status Legend5 - AWC6 - Approved
PROJECT : EPIC FOR INSTALLATION OF CEMS NOZZLES & ASSOCIATED STRUCTURES AT RG PLANT ATDUKHAN
Enclosed are the following documents as listed below
S.# DOC. NO. REV. PGS. DESCRIPTION SET *STS DUE DT.
1 3219-MS-CIV-001 0 13 MATERIAL APPROVAL REQUEST FOR REINFORCEMENTSTEEL (VARIOUS DIAMETER)
1 6 15-Jan-12
2 3219-MS-CIV-002 0 23 MATERIAL APPROVAL REQUEST FOR WATER PROOFINGMEMBRANE (FOSROC-PROOFEX GP 1.6MM THICK) &PROTECTION BOARD (6MM)
1 5 15-Jan-12
3 3219-MS-CIV-003 0 27 MATERIAL APPROVAL REQUEST FOR NON-SHRINKGROUT (CONBEXTRA GP)
1 6 15-Jan-12
4 3219-MS-CIV-004 0 29 MATERIAL APPROVAL REQUEST FOR RENDEROC BF2(BLOWHOLES FILLER FOR STRUCTURAL CONCRETE)
1 6 15-Jan-12
5 3219-MS-CIV-005 0 33 MATERIAL APPROVAL REQUEST FOR EXPOXY RESINCOATING (NITOCOTE NT 402)
1 6 15-Jan-12
6 3219-MS-CIV-006 0 49 MATERIAL APPROVAL REQUEST FOR JOINT SEALANT(THIOFLEX 600)
1 6 15-Jan-12
7 3219-MS-CIV-007 0 25 MATERIAL APPROVAL REQUEST FOR BONDING AGENT(NITOBOND EP & NETOBOND AR)
1 6 15-Jan-12
8 3219-MS-CIV-008 0 03 MATERIAL APPROVAL REQUEST FOR AGGREGATES20MM & 10MM DIAMETER
1 6 15-Jan-12
9 3219-MS-CIV-009 0 02 MATERIAL APPROVAL REQUEST FOR WASHED SAND 1 6 15-Jan-12
10 3219-MS-CIV-010 0 02 MATERIAL APPROVAL REQUEST FOR WATER 1 6 15-Jan-12
Page 1 of 2 27-Dec-11, 6:06PM DPF42-30-03, Rev 1 -21/02/2007
Please acknowledge receipt of the item(s) listed above by signing and returning a copy of this form.
Receivers Signature & Name Designation Date
DOPET Contact Authorized Signature Date
Noore Sattar
Project Manager
M. Luwerd Crisho
Lead Doc. Controller27-Dec-11
Remarks : CLIENT TN: EDD/GC11113800/EXT/TN/0027\ALL ITEMS EXCEPT 2 - ISSUE IN REV: A - AFCFOR ITEM 2 - ISSUE IN REV: 1 FOR APPROVAL
kamoradaHighlight
-
Doha Petroleum Construction Co. Ltd.Post Box 1744 , Doha - Qatar , Tel: +974-44600350 , Fax: +974-44601066
web: www.dopet.com - email: [email protected]
DOCUMENT TRANSMITTALTransmittal No.:
23305/CVL/TN/0005Dopet Job Ref.:
23305Project No.:
3219Contract No.:GC11113800
ToCompanyName : DOPET CIVIL DEPARTMENTAddress :Attn. : Mr. Ibrahim Wafi Said - Head of Civil DepartmentCC :
* Status Legend5 - AWC6 - Approved
PROJECT : EPIC FOR INSTALLATION OF CEMS NOZZLES & ASSOCIATED STRUCTURES AT RG PLANT ATDUKHAN
Enclosed are the following documents as listed below
S.# DOC. NO. REV. PGS. DESCRIPTION SET *STS DUE DT.
11 3219-MS-CIV-011 0 03 MATERIAL APPROVAL REQUEST FOR ORDINARYPORTLAND CEMENT AND SULPHATE-RESISTINGPORTLAND CEMENT
1 6 15-Jan-12
12 3219-MS-CIV-012 0 04 MATERIAL APPROVAL REQUEST FOR CONCRETE MIXEDDESIGNED PO38G77C40 40N/OPC
1 6 15-Jan-12
13 3219-MS-CIV-013 0 02 MATERIAL APPROVAL REQUEST FOR SCREEDCONCRETE MIX DESIGNED PS31G60C2020N/SRC/GABBRO
1 6 15-Jan-12
14 3219-MS-CIV-014 0 02 MATERIAL APPROVAL REQUEST FOR BLINDINGCONCRETE MIX DESIGNED PS31G60C1515N/SRC/GABBRO
1 6 15-Jan-12
Page 2 of 2 27-Dec-11, 6:06PM DPF42-30-03, Rev 1 -21/02/2007
Please acknowledge receipt of the item(s) listed above by signing and returning a copy of this form.
Receivers Signature & Name Designation Date
DOPET Contact Authorized Signature Date
Noore Sattar
Project Manager
M. Luwerd Crisho
Lead Doc. Controller27-Dec-11
Remarks : CLIENT TN: EDD/GC11113800/EXT/TN/0027\ALL ITEMS EXCEPT 2 - ISSUE IN REV: A - AFCFOR ITEM 2 - ISSUE IN REV: 1 FOR APPROVAL
-
EXTERNAL TRANSMITTAL NOTE ONSHORE ENGINEERING DEPARTMENT - DUKHAN PROJECTS
27-12-2011 12:54:26
GC11113800Contract No. : EDD/GC11113800/EXT/TN/0027
Transmittal No:3219Project No. :
EPIC FOR INSTALLATION OF CEMS NOZZLES & ASSOCIATED STRUCTURES AT RG PLANTContract Title :
Page 1 of 2
Company : DOPET
Forwarded to
F.a.o.: Noore Sattar
Codes
1
2
Approved - May Proceed (Re-submission Required)
Approved with Comments
3219-MS-CIV-0001
3219-MS-CIV-0002
3219-MS-CIV-0003
3219-MS-CIV-0004
3219-MS-CIV-0005
3219-MS-CIV-0006
3219-MS-CIV-0007
3219-MS-CIV-0008
3219-MS-CIV-0009
3219-MS-CIV-0010
3219-MS-CIV-0011
3219-MS-CIV-0012
3219-MS-CIV-0013
3219-MS-CIV-0014
QP Document No.0
0
0
0
0
0
0
0
0
0
0
0
0
0
Rev. MATERIAL APPROVAL REQUEST FOR REINFORCEMENT STEEL (VARIOUS DIAMETER) MATERIAL APPROVAL REQUEST FOR WATER PROOFING MEMBRANE (FOSROC-PROOFEX GP 1.6MM THICK) & PROTECTION BOARD (6MM) MATERIAL APPROVAL REQUEST FOR NON-SHRINK GROUT (CONBEXTRA GP) MATERIAL APPROVAL REQUEST FOR RENDEROC BF2 (BLOWHOLES FILLER FOR STRUCTURAL CONCRETE) MATERIAL APPROVAL REQUEST FOR EXPOXY RESIN COATING (NITOCOTE NT 402) MATERIAL APPROVAL REQUEST FOR JOINT SEALANT (THIOFLEX 600) MATERIAL APPROVAL REQUEST FOR BONDING AGENT (NITOBOND EP & NETOBOND AR) MATERIAL APPROVAL REQUEST FOR AGGREGATES 20MM & 10MM DIAMETER MATERIAL APPROVAL REQUEST FOR WASHED SAND MATERIAL APPROVAL REQUEST FOR WATER
MATERIAL APPROVAL REQUEST FOR ORDINARY PORTLAND CEMENT AND SULPHATE-RESISTING PORTLAND CEMENT MATERIAL APPROVAL REQUEST FOR CONCRETE MIXED DESIGNED PO38G77C40 40N/OPC MATERIAL APPROVAL REQUEST FOR SCREED CONCRETE MIX DESIGNED PS31G60C20 20N/SRC/GABBRO MATERIAL APPROVAL REQUEST FOR BLINDING CONCRETE MIX DESIGNED PS31G60C15 15N/SRC/GABBRO
Description1
2
1
1
1
1
1
1
1
1
1
1
1
1
Code1
2
3
4
5
6
7
8
9
10
11
12
13
14
ItemNo.
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
09-01-2012
Due dateTN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
TN/0025
YourRef.
kamoradaHighlight