VECTOR ACTIVE GUITAR CABINET 2 x 12 with 15 inch active 400 Watt RMS subwoofer. Can be matched with any head but optimized for use with the Theta Guitar Amplifier. Casters included.

THETA HEAD WITH FOOTPEDAL 300 Watt head, clean, and distortion channels, dual preamps, dual Decimator Noise Reduction and digital reverb. Can be matched with any cabinet, but optimized for use with the Vector Active Cabinet.

All Cabinets are Baltic Birch with black rubberized polyurethane covering; custom paint available.

Theta Head 29” W x 11.75” H x 9” D 40 lbs.

Vector Active 30” W x 30.75” H x 16.5” D 120 lbs.

THETA PREAMPLIFIER Each front end preamp has gain, bass, mid-level, mid-sweep and treble which provides amazing pre-distort tone shaping. Foot pedal included.

Theta Preamp 30” W x 30.75” H x 16.5” D 16 lbs.

GX4X12ST GUITAR CABINET This awesome 1 x 12 strait cabinet can handle tons of power. 300 Watts at an 8 ohm load. Featuring four Celestion G12T-75 speakers. Casters included.

STEVE LUKATHER VECTOR SL ACTIVE GUITAR SUBWOOFER

1 x 15 inch active subwoofer, 600 Watt RMS D-CAT power amplifier. Can be used with any guitar rig. Selection of external cabinet impedance with 3-way switch. Casters included.

THETA COMBO CABINET Combo amp for those who want real bottom end. 400 Watts RMS, two channel, fan cooled amplifier. 12 inch Celestion, 12 inch large excursion neo woofer.

GX4X12ST 30” W x 30” H x 14.5” D 95 lbs.

Lukather Vector SL Active 125 dB SPL 30” W x 20” H x 18.6” D 95 lbs.

Theta Combo Response to 45 Hz (-10 dB) 29.9” W x 19.9” H x 14.1” D 70 lbs.

VECTOR 112 GUITAR SUBWOOFER 1 x 12 inch active subwoofer, 300 Watt RMS D-CAT power amplifier. Same world-renowned Vector SL technology in a smaller, more lightweight package.

Vector 212 Extension Response to 40 Hz (-10 dB) 29.9” W x 19.9” H x 14.1” D 65 lbs.

VECTOR 212 EXTENSION CABINET By adding the active 400 Watt Vector 212 extension cabinet you literally double the available power of the Theta Combo system to 800 Watts RMS.

Vector 112 50 Hz to 130 Hz (-3 dB) 29.9” W x 19.25” H x 14.1” D 60 lbs.

BASS VECTOR PRO 118 CABINET Pro version 1000 Watts RMS internal power per cabinet. Built with high performance 18 inch woofer and dual 8 inch midrange speakers for stunning fidelity.

BETA BASS PREAMPLIFIER 2 active EQ’s, compression, exciter, Decimator Noise Reduction, designed to drive Bass Vector active cabinets.

All Cabinets are Baltic Birch with black rubberized polyurethane covering; custom paint available.

Beta Bass Preamp 19” W x 1.75” H x 6” D 8 lbs.

Bass Vector Pro 118 132 dB SPL 29 Hz to 5 KHz 30” W x 21.25” H x 24” D Active: 130 lbs. Passive: 115 lbs.

BASS VECTOR 118 CABINET Depth, impact, and definition from 18 inch woofer and dual 8 inch midranges, 600 Watts RMS into single cabinet, and 1000 Watts RMS total when a second passive cabinet is added. Line array topology for stacking with great horizontal dispersion. Also available as a passive cabinet.

Bass Vector 118 130 dB SPL 29 Hz to 5 KHz 30” W x 21.25” H x 24” D Active: 125 lbs. Passive: 110 lbs.

BASS VECTOR 115 CABINET 15 inch woofer and 8 inch midranges, 600 Watts RMS into single cabinet. 1000 Watts RMS when a passive cabinet is added. Same great bass performance now available in a smaller, more lightweight package.

DECIMATOR PRORACK G Rack mount two channel Decimator Noise Reduction system with dynamic filter and downward expander, designed specifically for guitar applications.

DECIMATOR PRORACK STUDIO Rack mount stereo Decimator Noise Reduction system with dynamic filter and downward expander, designed for studio or live sound applications where two independent channels of Decimator are needed for audio signal cleanup.

Bass Vector 115 129 dB SPL 35 Hz to 5 KHz 30” W x 19.25” H x 18.75” D Active: 104 lbs. Passive: 89 lbs.

ProRack G 19” W x 1.75” H x 6” D 8 lbs.

ProRack G Stereo Mod 19” W x 1.75” H x 6” D 8 lbs.

DECIMATOR PRORACK G STEREO MOD Rack mount stereo Decimator Noise Reduction system with dynamic filter and downward expander, designed specifically for guitar applications where a true stereo rig is being used.

ProRack Studio 19” W x 1.75” H x 6” D 8 lbs.

DECIMATOR PEDAL Decimator Noise Reduction pedal. Most advanced, patented, state-of-the-art technology in real time noise reduction. The Decimator design offers a novel approach to tracking the envelope of the input signal called Time Vector Processing™.

G String 2.7” W x 5” H x 2.3” D Chrome chassis 2 lbs.

Totally Blues 2.7” W x 5” H x 2.3” D Chrome chassis 2 lbs.

FETISH DISTORTION PEDAL Gain, tone, level, and a fat control for total control over the sound of your distortion. Utilizes field effect transistor for ultra-clear, tube-like distortion. Treble boost and clean boost are also available.

Fetish 2.7” W x 5” H x 2.3” D Chrome chassis 2 lbs.

TOTALLY BLUES OVERDRIVE PEDAL Gain, tone, level, and a mojo control for total control over the sound of your overdrive. Utilizing asymmetrical clipping technology. Mojo control adds low end to distortion for thicker notes.

DECIMATOR G STRING PEDAL Decimator Noise Reduction pedal was designed for those who want the ultimate performance from a noise reduction pedal. The G String pedal tracks the signal directly from the guitar, which allows you to switch from clean to high gain without ever changing the threshold setting. Allows connection of the processing channel of the Decimator to be inserted into your effects loop or after your high gain pedals or preamp.

Decimator 2.7” W x 5” H x 2.3” D Chrome chassis 2 lbs.

ISP raises the bar on ultimate guitar performance with the patent pending Decimator ProRack G™. The Decimator ProRack G guitar noise reduction system defines a new standard for excellence in real time noise reduction performance. The Decimator ProRack G was designed to provide the maximum possible performance in a rack mount, dual channel noise reduction system designed specifically for extremely high gain guitar amplifiers. The Decimator ProRack G is the only system in the world designed with two channels of single ended noise reduction configured specifically for high gain guitar applications, allowing one channel to deliver noise reduction for the guitar directly and a second channel to eliminate amplifier gain noise. Channel one eliminates the 50 or 60 cycle hum, buzz, stage light noise, and any other noise picked up directly by the instrument. The ProRack control circuit of the second channel detects and tracks the guitar signal directly while the signal processing audio chain is patched into the effects loop of the high gain guitar amplifier. Now you can quiet down even the most insane amounts of noise with any squealing problem that the high gain guitar player fights. You know how difficult this problem can be. You play staccato notes and in between each note you have a squeal or burst of feedback that’s virtually impossible to control. Problem solved with the Decimator ProRack G. By proper setting of the threshold for channel one and channel two, you can eliminate this problem for good. The Decimator ProRack G has dual processing channels incorporating both low-level downward expansion and dynamically controlled low-pass filtering in a very easy to use single rack space unit. The Decimator ProRack G is based on ISP Technologies patent pending Time Vector Processing™, which provides the most adaptively dynamic release response characteristics of any real time noise reduction system. The patent pending Time Vector Processing dynamic response circuit is used to control the release time constant of both the downward expander and dynamic filter. Not only does the Decimator ProRack G deliver the most stunning noise reduction, it also solves the problem of needing to adjust the threshold setting every time you change gain or switch channels. By using the input guitar signal to drive both channels’ level detection circuitry, you can set the threshold based on your specific guitar and never need to make another threshold adjustment. This will give you the correct threshold with clean, crunch, and even monstrous amounts of gain and if you use pedals you can insert them in the loop between the output of the Decimator channel one and the input of the guitar amplifier. Also available in the Decimator ProRack G Stereo Mod version for the guitarist who plays a stereo rig. Specifications: Input Impedance: 20k ohms Output Impedance: less than 1k ohm Maximum Input Level: +20dbu Dynamic Range: greater than 118dB typical Power Consumption: 350ma THD: less than .05% at 0dbu Dimensions: 1.75” H x 19” W x 7” D

*HUSH is a trademark of Rocktron a division of GHS Strings

The Decimator G String Noise Reduction Pedal™ was designed for those who want the ultimate performance in a foot pedal and delivers performance like that of the renowned ISP Decimator ProRack G. The Decimator G String provides a totally independent channel of Decimator noise reduction that can be inserted into a series effects loop or after a preamp section with the advantage of having the Decimator level detectors track the guitar signal directly. With the G String Pedal you can set the threshold, and no matter what level of noise, the Decimator will track perfectly without any side effects. The amazing thing is that you can switch from high gain to your clean channel and never have to switch the Decimator G String off due to the threshold being set too high. It’s simply transparent. The G String noise reduction pedal has an input to connect directly to a guitar and a buffered output signal to feed the front of a guitar rig directly while providing a separate audio channel of Decimator that can be inserted in the signal chain of any guitar rig. You can insert any other pedals between the output of the Decimator G String and the input of your guitar amplifier. This allows the Decimator G String Pedal to remove any level of noise you may have, even with overdrive pedals, at the front end of the amp. SPECIFICATIONS: Input Impedance: 500k ohms Maximum Input Level: +12dbu Effective Noise Reduction: Greater Than 60dB Dynamic Range: Greater Than 100dB Total Harmonic Distortion: .5% Typical Power Consumption: 35ma @9VDC Release Response: Program Dependant Based on Time Vector Processing

ISP Technologies presents the latest in Noise Reduction technology: The DECIMATOR NOISE REDUCTION SYSTEM™. From the original inventors of the *HUSH® noise reduction comes the latest, most advanced, patent pending, state-of-the-art technology in real time noise reduction. The Decimator offers a revolutionary breakthrough in Noise Reduction processing with an unparalleled level of performance. The HUSH system, as well as all other noise reduction systems suffers from one major problem inherent in their design: The system cannot be immediately responsive to very short-term staccato notes. The typical downward expander noise reduction system suffers from a dead zone in the release response characteristic, which causes a compromise in tracking both fast decaying notes and long sustained notes. The Decimator design offers a novel approach to tracking the envelope of the input signal called Time Vector Processing™. Due to this novel approach in controlling the expander, the Decimator system will instantly respond to short staccato notes and, at the same time, will provide a very slow ripple free control of long sustained notes. This means that the Decimator Noise Reduction system is the most transparent and highest performance noise reduction system available. The Decimator Pedal is extremely easy to use; simply insert the Decimator at the end of your chain of existing pedals, or insert the Decimator Pedal in the effects loop of your amplifier to clean up the noise present at the amplifier input as well as the noise in the amplifier’s preamp section. Packaged in a rugged, beautifully polished smooth chrome chassis, the Decimator pedal offers reliability, performance, and beauty in one compact pedal. Audition the Decimator today and experience the highest level of performance available in a noise reduction system. SPECIFICATIONS: Input Impedance: 470k ohms Output Impedance: Less Than 150 ohms Maximum Input Level: +9dbu Dynamic Range: 95dB Typical Power Consumption: 30ma Total Harmonic Distortion: Less Than .05% Dimensions: 5” x 2.7” x 2.3”

The THETA HEAD™ offers a unique approach to the guitar amplifier, by providing two selectable input pre-distort preamplifiers. Using the THETA head is like having two low-noise, extremely high quality preamp pedals at the input of the amplifier. Each front end preamp has gain, bass, mid level, mid sweep, and treble which provides amazing pre-distort tone shaping. The amplifiers’ “Clean” and “Distort” circuits have the same post distort tone shaping. Tone beyond your wildest dreams! No other amplifier, Tube, Solid State, or Digital even comes close to the sonic flexibility of the THETA. The Clean channel has addit ional tone shaping with the inclusion of a Presence control, providing more than 20 dB of high frequency boost. You want gain? The THETA has more gain available than any amplifier ever produced. With greater than 140 dB of gain, you can control the gain and make it useable only because we’ve included dual independent full-featured Decimator Noise Reduction systems. The THETA is the first amplifier to incorporate Dynamic Saturation Modulation™, which delivers the actual feel of a saturated tube power amplifier. The THETA also packs a huge punch; the internal D-CAT™ (Dynamic Current Amplification Technology) power amplifier delivers more than 300 Watts RMS into a 4 ohm load and 150 Watts into an 8 ohm load. Derek Bower, renowned IC design engineer from Analog Devices, and Buck Waller, of ISP Technologies, developed the patent pending D-CAT power amplifier technology. The D-CAT is a extremely high current power amplifier technology capable of driving a .5 ohm load. This means that the D-CAT amplifier delivers better transient response and punch than any other amplifier technology available.

ACTIVE 400 WATT 15” SUBWOOFER BUILT-IN THETA VECTOR CABINET

300 WATT THETA HEAD

DUAL PRE-GAIN PREAMPLIFIERS

DUAL DECIMATOR NR PROCESSORS

D-CAT POWER AMPLIFIER TECHNOLOGY

LOW END POWER FOR DETUNERS AND SEVEN STRING PLAYERS

STUDIO QUALITY DIGITAL REVERB

MID SWEEP ON ALL CHANNELS

The THETA VECTOR ACTIVE GUITAR SYSTEM™ is the highest performance guitar system ever produced. It is the most powerful at 1100 Watts RMS total power, the most flexible tone with dual amplifiers and dual front end pre-distort preamplifiers, the most gain with more than 140 dB, the most low end with 800 Watts dual active subwoofers, and the quietest, with dual Decimator Noise Reduction Systems.

The patent pending VECTOR SL™ 600 WATT ACTIVE GUITAR SUBWOOFER was developed in collaboration with one of the greatest and most prolific guitarists of our era: Steve Lukather. Because of a long-standing relationship with Buck Waller of ISP Technologies, Luke came to Buck with his desire to see a guitar subwoofer that would work with any guitar system. Based on specific inputs from Lukather, ISP engineers have designed the perfect complement for any guitar setup: the VECTOR SL. Years of experience in designing the highest performance Active Sound Reinforcement cabinets has allowed ISP Technologies engineers to develop the ultimate active guitar subwoofer. The VECTOR SL incorporates ISP’s patented D-CAT™ power amplifier technology with greater than 600 Watts of RMS power. Connect the output of any guitar head to the VECTOR SL and plug in your favorite speaker cabinet and your supercharged VECTOR SL system is ready to ROCK. The subwoofer level is adjustable via the sub level control on the back of the VECTOR SL cabinet. The internal 600 WATT RMS active 15 inch subwoofer delivers more deep, low end punch than any other guitar subwoofer cabinet available. The VECTOR SL subwoofer extends your bottom end all the way down to 45Hz delivering enough low end bass to match the frequency response of any 7-string guitar. Tune down as far as you want and the VECTOR SL continues to perform. To all this performance add three-way power amplifier protection and you have the most reliable active guitar subwoofer system ever made. The VECTOR SL’s internal D-CAT amplifier has global thermal protection, thermal protection built in the power transformer, and an on board distortion limiter circuit to eliminate the possibility of feeding square waves to the woofer. This means that, as long and hard as you drive the VECTOR SL, even to its maximum limits, you never have to worry about failures. VECTOR SL ACTIVE GUITAR SUBWOOFER SPECIFICATIONS: Subwoofer Power Amplifier: Internal 600 Watt RMS D-CAT Head Subwoofer Level Control Protection: Global Thermal Power Amplifier Protection / Power Transformer Thermal Protection Crossover Inpedance Selection: 4 ohm, 8 ohm, 16 ohm Maximum SPL: 128dB Typical Power Line Consumption: 4-amps / 6-amps Peak Dimensions: 30” W X 20” H X 18.5” D Weight: 90 lbs. Side Mount Castors

“These subs make havin’ cabs on stage worth something again, yes!!!!! monitors? what monitors?”

Stephen Carpenter of the Deftones

For the Vector SL guitar subwoofers

“Finally I can feel my guitars kicking me in the gut every night, thanks to the SL subs. My guitar tone is razor sharp like a samurai! I don’t like a ton of bass dialed into my guitar sound, it will turn my guitars into mud. But I do like to feel the low end chugging when I am on stage every day on our Transgression world tour. So there’s only one solution, The SL Subs!!! The cabinets link into the back of my guitar cabinets and they are completely separated from my main guitar sound. So now I have the best of worlds, my razor sharp signature guitar sound and the massive low end from my 15 inch subwoofers. Just like when you add that subwoofer in your car, the SL subs give you that same smile while on stage rocking in front of thousands of fans every night!”

“At the 2006 NAMM music trade show, I was introduced to ISP Technologies, and most importantly, the 300 Watt Theta guitar amplifier. After playing through this crunch machine for fifteen minutes or so, I was completely in love! Buck Waller has created a sweet, beautiful monster. The Theta’s tone is big, sweet, and crunchy - just the way I like it. Needless to say, I’m very much looking forward to having this killer amp (as well as the Vector 400 Watt powered subs) as a part of my tone arsenal, ISP rules.”

“The Decimator nails all the stop/go riffing I do and also makes sure any outside noise from various stages on the road is killed so my tone is clean and cutting and it makes sure my stops are dead on! Don’t mess around, get this now!”

Greg E. Noll of Crazy Ivan

Shaun Glass of Soil

Christian Wolbers of Fear Factory

www.isptechnologies.com

5479 Perry Drive, Suite B. Waterford, MI 48329

PHONE: [248] 673-7790 FAX: [248] 673-7696

Copyright © 2012 ISP Technologies

Revised 01.12

NOTE: All products may be covered under one or more of the following patents with other US and foreign patents pending

7,035,413, 6,944,305, 6,931,134, 6,831,514, 6,091,013