These instructions and the images herein are …NOTE: Early-model Digifant vehicles have ALL WHITE...
1
These instructions and the images herein are proprietary. Any unauthorized reproduction is prohibited. GVW-025-906-302A GoWesty Air Flow Meter Filter Circuit Page 1 of 1 GoWesty Camper Products • 1119 Los Olivos Ave, Los Osos, CA 93402 • 888-469-3789 • www.gowesty.com NOTE: NOTE: NOTE: NOTE: Early-model Digifant vehicles have ALL WHITE wires going to the air flow meter. These wires do have a number indicator printed on the insulation that is not only hard to see, but is often worn off the wire completely. It is VERY VERY VERY VERY important to follow the instructions EXACTLY EXACTLY EXACTLY EXACTLY and install this kit by labeling each wire—and cutting and splicing ONE WIRE ONE WIRE ONE WIRE ONE WIRE at a time. 1. Unplug the factory connector from the Air Flow Meter (AFM). 2. Remove the rubber boot from the connector. Note the numbers on the connector and place numbered pieces of tape on each wire which corresponds to the numbers on the plug. See diagram below. Warning: Warning: Warning: Warning: DO NOT SKIP THIS STEP! These numbers will keep you from making a terrible mistake! READ BEFORE CONTINUING: READ BEFORE CONTINUING: READ BEFORE CONTINUING: READ BEFORE CONTINUING: The GoWesty AFM Filter Circuit is designed to be spliced into the factory Digifant harness. DO NOT cut all of the wires at once DO NOT cut all of the wires at once DO NOT cut all of the wires at once DO NOT cut all of the wires at once. Start from one side and install the GoWesty AFM Filter Circuit one one one one wire at a time wire at a time wire at a time wire at a time. 3. Cut the first wire about 1 to 2 inches behind the rubber connector boot on the factory harness. 4. Pull the braided loom on the GoWesty harness up to access the wire ends. Using the provided uninsulated butt connectors and shrink tubing, join the factory wire to the appropriately numbered wire on the GoWesty harness. a. Repeat the steps 3 and 4 for the remaining wires. We strongly suggest soldering each connection before installing the shrink tubing over the splice. Be careful not to melt any wire insulation. 5. When all connections have been crimped, soldered (optional, but encouraged), and the heat shrink tubing installed, stretch the braided wire loom over the crimped connections and tape the end to the factory wiring loom using some electrical tape. The GoWesty AFM Filter can now be plugged into the AFM. Tools Needed Tools Needed Tools Needed Tools Needed • Wire strippers • Crimping tool for non-insulated terminals • Heat gun or lighter • Soldering iron and solder (optional) DISCLAIMER: DISCLAIMER: DISCLAIMER: DISCLAIMER: This kit has been designed for easy installation. However, it does involve some wiring. The installation of this kit is not within everyone's ability. Read through these instructions carefully and decide if installing it is for you. If not, please take your vehicle to an automotive electrician. Wiring errors can be troublesome and hazardous.
Transcript of These instructions and the images herein are …NOTE: Early-model Digifant vehicles have ALL WHITE...
These instructions and the images herein are proprietary. Any unauthorized reproduction is prohibited.
GVW-025-906-302A GoWesty Air Flow Meter Filter Circuit
Page 1 of 1
GoWesty Camper Products • 1119 Los Olivos Ave, Los Osos, CA 93402 • 888-469-3789 • www.gowesty.com
NOTE: NOTE: NOTE: NOTE: Early-model Digifant vehicles have ALL WHITE wires going to the air flow meter. These wires do have a number indicator printed on the insulation that is not only hard to see, but is often worn off the wire completely. It is VERYVERYVERYVERY important to follow the instructions EXACTLYEXACTLYEXACTLYEXACTLY and install this kit by labeling each wire—and cutting and splicing ONE WIREONE WIREONE WIREONE WIRE at a time.
1. Unplug the factory connector from the Air Flow Meter (AFM). 2. Remove the rubber boot from the connector. Note the numbers on the connector and place numbered pieces of tape
on each wire which corresponds to the numbers on the plug. See diagram below. Warning:Warning:Warning:Warning: DO NOT SKIP THIS STEP! These numbers will keep you from making a terrible mistake!
READ BEFORE CONTINUING:READ BEFORE CONTINUING:READ BEFORE CONTINUING:READ BEFORE CONTINUING: The GoWesty AFM Filter Circuit is designed to be spliced into the factory Digifant harness. DO NOT cut all of the wires at onceDO NOT cut all of the wires at onceDO NOT cut all of the wires at onceDO NOT cut all of the wires at once. Start from one side and install the GoWesty AFM Filter Circuit one one one one wire at a timewire at a timewire at a timewire at a time....
3. Cut the first wire about 1 to 2 inches behind the rubber connector boot on the factory harness. 4. Pull the braided loom on the GoWesty harness up to access the wire ends. Using the provided uninsulated butt
connectors and shrink tubing, join the factory wire to the appropriately numbered wire on the GoWesty harness. a. Repeat the steps 3 and 4 for the remaining wires. We strongly suggest soldering each connection before
installing the shrink tubing over the splice. Be careful not to melt any wire insulation. 5. When all connections have been crimped, soldered (optional, but encouraged), and the heat shrink tubing installed,
stretch the braided wire loom over the crimped connections and tape the end to the factory wiring loom using some electrical tape. The GoWesty AFM Filter can now be plugged into the AFM.
Tools NeededTools NeededTools NeededTools Needed • Wire strippers • Crimping tool for non-insulated terminals • Heat gun or lighter • Soldering iron and solder (optional)
DISCLAIMER:DISCLAIMER:DISCLAIMER:DISCLAIMER: This kit has been designed for easy installation. However, it does involve some wiring. The installation of this kit is not within everyone's ability. Read through these instructions carefully and decide if installing it is for you. If not, please take your vehicle to an automotive electrician. Wiring errors can be troublesome and hazardous.
