THERMAL ENGINEERING(ME 2301 )

M.R.SWAMINATHANAssistant Professor

Department of Mechanical EngineeringAnna University Chennai

Chennai-25

DIESEL CYCLE

The diesel cycle is the ideal cycle for CI

(Compression-Ignition) reciprocating engines.

The CI engine first proposed by Rudolph Diesel

in the 1890s, is very similar to the SI engine,

differing mainly in the method of initiating

combustion.

In diesel engines, ONLY air is compressed

during the compression stroke, eliminating

the possibility of auto-ignition.

Diesel engines can be designed to operate at

much higher compression ratios, typically

between 12 and 24.

The fuel injection process in diesel engines

starts when the piston approaches TDC and

continues during the first part of the power

stroke.

Therefore, the combustion process in these

engines takes place over a longer interval.

Because of this longer duration, the

combustion process in the ideal Diesel

cycle is approximated as a constant-

pressure heat-addition process.

This is the ONLY process where the

Otto and the Diesel cycles differ.

Ideal Cycle for CI Engines

1rk1r

r11

TTkTT1

qq1

qwη

TTCuuq

TTChhquu

c

kc

1k23

14

in

out

in

netDieselth,

14v14out

23p23in23outbin wq ,

2

3

2

1

cr

r

and

Where,

Thermal efficiency of Ideal Diesel Cycle

Under the cold-air-standard

assumptions, the efficiency

of a Diesel cycle differs from

the efficiency of Otto cycle by

the quantity in the brackets.

The quantity in the brackets is always greater than 1. Therefore, hth,Otto > hth, Diesel when both cycles operate on the same compression ratio.

Also the cuttoff ratio, rc decreases, the efficiency of the Diesel cycle increases.

DUAL / LIMITED PRESSURE CYCLE

BRAYTON CYCLE – GAS TURBINEThe open gas-turbine cycle can be modeled as a closed cycle, as shown in the figure below, by utilizing the air-standard assumptions

12 Isentropic compression (in a compressor)

23 Constant pressure heat addition

34 Isentropic expansion (in a turbine)

41 Constant pressure heat rejection

BRAYTON CYCLE - PROCESSES

/k1kp

232

141

23p

14p

in

out

in

netBraytonth,

r11

1/TTT1/TTT1

TTCTTC

1

qq1

qwη

ratio. pressure the is PPr and ,

TT

PP

PP

TT where

1

2p

4

3/k1k

4

3/k1k

1

2

1

2

The highest temperature in the cycle occurs at the end of the combustion process, and it is limited by the maximum temperature that the turbine blades can withstand.

VALVE TIMING • Why valve Timing?• Is it significant? Yes

Burning exact quantity of Air/Fuel mixture at right time and place produces more power output

Moreover more economy and lesser emissions

VALVE TIMING DIAGRAM- actual

I.C.ENGINES

External Combustion EngineA device where the working fluid is obtained indirectly

e.g Steam or Locomotive boiler

Coal is first burnt and then the heat energy obtained from coal is utilised to transform water to steam which is the working fluid.

So the name External combustion engine just to differentiate from an I.C. engine

CLASSIFICATION OF I.C ENGINES

Internal combustion engines are classified according to

• Fuel used – D/P/G• Cycle of operation - O/Di/Du• Ignition system – SI / CI• Number of strokes – 2S / 4S• Type of cylinder arrangement – In / V/ H• Type of cooling – Air/Water

• Speed of engine – L / M / H• Type of Lubrication • No. of cylinders – Single / multi

CLASSIFICATION OF I.C ENGINES

COMPONENTS OF I.C ENGINE• Cylinder Block

– Part of engine frame that contains cylinders in which piston moves

– Supports liners & head• Cylinder Head

– Serves to admit, confine, and release fuel/air

– Cover to cylinder block– Supports valve train

• Crankcase– Engine frame section that

houses the crankshaft

COMPONENTS OF I.C ENGINE • Piston

– Acted on by combustion gases– Lightweight but strong/durable

• Piston Rings– Transfer heat from piston to cylinder– Seal cylinder & distribute lube oil

• Piston Pin– Pivot point connecting piston to

connecting rod• Connecting Rod

– Connects piston & crankshaft– Reciprocating (rotating motion)

COMPONENTS OF I.C ENGINE • Crankshaft

– Combines work done by each piston– Drives camshafts, generator, pumps, etc.

• Flywheel– Absorbs and releases kinetic energy of piston strokes

(smoothes rotation of crankshaft)• Valves

– Intake: open to admit air to cylinder (with fuel in Otto cycle)

– Exhaust: open to allow gases to be rejected• Camshaft & Cams

– Used to time the addition of intake and exhaust valves– Operates valves via pushrods & rocker arms

I.C ENGINE TERMINOLOGY• Bore is the diameter measurement of the cylinders in a

piston engine• Stroke is a single traverse of the cylinder by the piston

(from TDC to BDC)– 1 revolution of crankshaft = 2 strokes of piston

• Compression Ratio is defined as the ratio of the volume of the cylinder at the beginning of the compression stroke (when the piston is at BDC) to the volume of the cylinder at the end of the compression stroke (when the piston is at TDC)– Common sparkignition compression ratio:6:1 to 12:1– Common compression-ignition ratio: 16:1 to 23:1

Four stroke cycle• Intake stroke: intake valve opens while the piston moves down from

its highest position in the cylinder to its lowest position, drawing air into the cylinder in the process.

• Compression stroke: intake valve closes and the piston moves back up the cylinder. This compresses the air & therefore heats it to a high temperature, typically in excess of 1000°F (540°C). Near the end of the compression stroke, fuel is injected into the cylinder. After a short delay, the fuel ignites spontaneously, a process called auto ignition.

• Combustion stroke: The hot gases produced by the combustion of the fuel further increase the pressure in the cylinder, forcing the piston down

• Exhaust stroke: exhaust valve opens when the piston is again near its lowest position, so that as the piston once more moves to its highest position, most of the burned gases are forced out of the cylinder.

Four stroke cycle

I.C.ENGINE PARTS

I.C ENGINE PARTS

OPERATION OF CAM

MULTI CYLINDER I.C. ENGINE

TWO STROKE I.C. ENGINE