THE WACO JUMPFORM - Waco Kwikform€¦ · FORMWORK ENQUIRIES NSW Block 1-3/1B Unwin Street Rosehill...
Transcript of THE WACO JUMPFORM - Waco Kwikform€¦ · FORMWORK ENQUIRIES NSW Block 1-3/1B Unwin Street Rosehill...
SCAFFOLDING & FORMWORK SPECIALISTS
THE WACO JUMPFORM
JUMPFORM Benefits and Advantages
• Crane Independent Core JumpformMachine
• Safe working and loading platformswith fully enclosed perimeter providesfall and weather protection. Thisensures safety when working at severallevels above slab construction level.
• Innovative and safe way to installpre-assembled jumpform platforms,perimeter cladding and access stairs.
• German engineered hydraulicclimbing devices with 10-ton loadcapacity. The Hydraulic Load Distribution Technology enables the jumpform to be lifted evenly during climbing stage.
• Greater stability during climbing stagedue to positive fixings to walls andeven distribution of braced posts.
• Experienced Specialist JumpformSupervisors and Engineers will provideservice and support throughout theproject.
• Due to the higher loads that can becarried by the hydraulic climbingdevices, other safety and operationalfeatures can be installed on thejumpform system; such as externalaccess stairs, reinforcement steelloading area and concrete boompump.
• Large working spaces enables betterproductivity.
• Typical climbing speed is about300mm per minute.
• Fast construction cycle times can beachieved.
• The jumpform is anchored topreviously poured walls which allowsfaster core construction cycles wellahead of the typical slab constructioncycles.
• Shutters are suspended from theoverhead steelwork by girder trolleysand with the help of push-pull propsmanual striking, roll back, closing andplumbing of formwork are achievedwith ease.
Index Date Description AuthorA 23/06/2016 FOR CONSTRUCTION G.McG
ONEFORM A3NTSONEFORM PTY. LTD.396 New Cleveland RdTingalpa, QLD, 4173Ph: 07 3890 0249Fax: 07 3890 0217
FABRICATION QA CHECKLISTNAME DATE
FABRICATED BYCHECKED BYHOURS TAKEN 9036D.KING A
1602
BURANDA TOD
G.McG
ACS-AU JUMP FORM
1602-JF-000
15/06/2016GENERAL NOTES:1. ALL HOLES TO BE 22Ø U.N.O.2. ALL WELDS TO BE 6mm FILLET U.N.O.3. THIS DRAWING MUST NOT BE SCALED.
ITEM CHECKED SIGNED
SHUTTER ROLLERS WITH HANGER BRACKETS
CLIMBING RAILS (6.3m FOR POURS 3M OR LESS)
CAST IN THREADED ANCHOR PLATES (DW26) 1PER SHOE (CONSUMABLE)SCREW IN CONE (M30/DW26) - 1 PER SHOESW22 HEX DRIVER46mm SOCKET FOR M303 PHASE POWER LEAD (CHECK SITE FORLENGTH)SHUTTER HANGING PLATFORM BRACKETS(STEEL FIXERS)SCAFFOLD PLANKS FOR PLATFORMCORNER HANDRAILSACCESS LADDERSRUBBER TRIMS FROM PLATFORM WALLCONCRETE PUMP ANCHORSLIGHTING INSTALLEDRUBBER STRIPS FOR GAPSMOTORSHYDRAULIC FLUID (HC68)HYDRAULIC LINESEMERGENCY ACCESS PANELACCESS STAIR TOWERSOVERALL CHECKED BY YARD MANAGER
ITEM CHECKED SIGNED
LIFTING POINTS LOCATEDCRANE RADIUS CHECKED FOR LOADSITE CLEARANCES CHECKEDSHUTTERS DESIGNED FOR ROLLERSACCESS PROVIDEDEMERGENCY ACCESSWIDE LOAD ROUTE ACCEPTABLESYSTEM REACTIONS PROVIDEDOVERALL CHECKED BY ENG. MANAGER
LEVEL X LEVEL X
LEVEL X
LEVEL X + 1
LEVEL X
LEVEL X LEVEL X
LEVEL X + 1
STEP 1Steel fixing
STEP 4Strike and Retract Formwork
STEP 2Concrete pour
STEP 5Climb upper platforms and Formwork
STEP 3Climb lower platform
STEP 6Jumpform on upper anchors ready for steel fixing
CONSTRUCTION SEQUENCE: 6 Easy Steps
Most of the system is pre-assembled in the yard.
System is finally assembled in easy-to-use sections on site.
PRE-ASSEMBLY
THE POWER OF JUMPFORM
Due to the higher loads that can be carried by the hydraulic climbing devices, other
safety and operational features can be installed on the jumpform system; such as external access stairs, reinforcement steel
loading area and concrete boom pump.
Panorama Project in Brisbane. Watefront Project in Melbourne
www.wacokwikform.com.au
Fast, safe, affordable.Experience the Waco difference.
FORMWORK ENQUIRIES
NSWBlock 1-3/1B Unwin Street Rosehill NSW 2142T: (02) 9684 8880E: [email protected]
QLDBuilding 3/84 Christensen Road South Stapylton QLD 4207T: (02) 9684 8880E: [email protected]
VIC50-60 Emu RoadMaidstone VIC 3012T: (03) 8368 9211E: [email protected]
WACO KWIKFORM GROUP
CORPORATE HEAD OFFICE Suite 2.02, Level 23 Rider Blvd Rhodes NSW 2138
T: (02) 8399 9100 E: [email protected]
SCAFFOLDING ENQUIRIEST: 1300 333 113