THE RESULTS€¦ · 8"258mm Max. 9 3 8"238mm Max. 7 8"22mm Conduit Entrance 8 3 16"208mm 9 16"15mm...
Transcript of THE RESULTS€¦ · 8"258mm Max. 9 3 8"238mm Max. 7 8"22mm Conduit Entrance 8 3 16"208mm 9 16"15mm...
3
100
80
60
40
20
0
E.co
li
Salm
onel
la
Influ
enza
A
Stap
h
MRS
A
99.03% 99.17%96.43% 96.61%
93.49%
LAB TEST RESULTS - AVERAGE REDUCTION RATES
Average reduction rates on tests performed by EMSL and ATL Labs to modified ASTM International Standard E1153. Testing conducted under lab conditions only. Your results may vary. Sample microorganisms were placed under the dryer nozzle for 35 seconds. Underwriters Laboratory undertook air quality testing to its UL867 Standard for Electrostatic Air Cleaners and to California Air Resources Board (CARB) standards for ozone emissions.
C A L I F O R N I A A I R
RESOURCES BOARDUSC ®
THE RESULTSSPEAK FOR
THEMSELVES.
Since the eXtremeAir CPC is the first hand dryer to employ Cold Plasma Clean® technology, we had to conduct vigorous research to determine the most appropriate test standards. After consulting with leading regulatory microbiologists and some of the best research labs in the country, it was determined that ASTM International Standard E1153 could be modified to test the efficacy of our dryer with cold plasma technology.
Two independent microbiology laboratories, EMSL and ATL were selected to conduct the testing based on their credentials. EMSL Labs is an elite CDC-certified lab with AIHA accreditation in industrial hygiene and environmental microbiology. Antimicrobial Test Labs, ATL, is a GLP-compliant laboratory audited by the EPA and FDA.
The eXtremeAir CPC hand dryer is considered a pesticidal device by the US Environmental Protection Agency (EPA) and is made at our factory in the USA. OurEPA Establishment Number 091022-MI-001.
The eXtremeAir CPC is not a medical device and as such is not intended to diagnose, cure, mitigate, treat or prevent disease. This hand dryer is not intended to clean the air in the entire restroom.
DRYER PLACEMENT : Dryers should be placed at least 2 feet apart and at least 12” from washbasin. Do not install dryer over washbasin. Automatic dryers should be at least 18” above any projection which may interfere with the operation of the automatic sensor. In congested areas the dryers should be located to create a flow from the washbasin to the dryer and to the exit. Recommended mounting heights are shown in the table below.
DRYER INSTALLATION Dryers must be installed by a licensed electrician. A single phase dedicated 15 amp or 20 amp electrical line is required. (The eXt series does not require a dedicated line.) Dryers must be properly grounded. One side of dryer should be mounted to a stud. All surface mount dryers are provided with conduit entrances for both in-wall and surface wiring. For indoor use only.
QUANTITY ESTIMATE, HAND DRYER:Average traffic washroom...1 dryer per 2 washbasins Heavy traffic washroom...... 1 dryer per washbasin 54” wash fountain...............4 dryers per sink
SHIPPING WEIGHT: ABS 9 lbs, M/BG/SS 10 lbs
5-5/8(143mm)
eXtremeAir Series Surface Mount
Cover Mounting Diagram
10 18 " 258mm Max.
9 38 " 238mm Max.
78 " 22mm
Conduit Entrance
8 316 " 208mm
916 " 15mm Max.
916 " 15mm Max.
8 1516 " 228mm
1 12 " 38mm
1516 " 24mm
Mounting Holes for1/4" [M6] screws
Template is for all American Dryer
EXTREMEAIR, ADVANTAGE AND GLOBAL Series dryers
Outer perimeterof ABS Cover
Revised 10/06/2014
RECOMMENDED MOUNTING HEIGHTS FROM BOTTOM OF DRYER TO FINISHED FLOOR
Men Women Children Disabled
All Hand Dryers 44” 42” 32”- 42” 36”
ACCESSORIES
ADA-WGWALL GUARD
ADA-RKRECESS KIT
AP
ADAPTER PLATE
Accessories Reference ChartADA-WG
ADA-RK
AP
ADA Compliant seamless stainless steel wall guard
ADA Compliant seamless stainless steel recess kit
Stainless steel universal adapter plate
eXtremeAir SERIES MOUNTING DIAGRAMS
Stainless Steel
eXtremeAir® gXt & eXt hand dryer series
White ABS Steel White Epoxy Steel Black Epoxy
COMPACT • HIGH SPEED • ENERGY EFFICIENTTHE
ORIGINAL The original high speed, compact, energy efficient hand dryer
gXt model reference chart
White ABS GXT9
Steel White Epoxy GXT9-M
Steel Black Epoxy GXT9-BG
Stainless Steel GXT9-SS
Dimensions: 10-1/8” W x 9-3/8” H x 5-5/8” D
gXt specifications
Dry Time 10 + Seconds (Adjustable)
Air Velocity 19,000-10,000 LFM (Linear Feet per Min.)
Air Temperature 135˚ F at 72˚ F room temperature
Universal Voltage 100-240 V, 50/60Hz
Power 1500 - 800 W adjustable
The original and still the best:
• Adjustable Sound& Speed
• Universal Voltage• Sleek, compact
design
eXt model reference chart
White ABS EXT7
Steel White Epoxy EXT7-M
Steel Black Epoxy EXT7-BG
Stainless Steel EXT7-SS
Dimensions: 10-1/8” W x 9-3/8” H x 5-5/8” D
eXt specifications
Dry Time 12 + Seconds (Adjustable)
Air Velocity 19,000-10,000 LFM (Linear Feet per Min.)
Air Temperature 85˚ F at 72˚ F room temperature
Universal Voltage 100-240 V, 50/60Hz
Power 540 - 300 W adjustable
One of the most energy efficient, eco friendly hand dryer’s ever
Eco no-heat technology:
• Significantenergy savings
• Multiple units onone line
• Reducedinstallation costs
• Standby power ofless than 1 watt
EXTREMEAIR - Distributor2270 Worth Ln, Ste A I Springdale, AR 72764 I U.S.A.
Phone: 479-353-0825 U.S.A
Web: AR316.comEmail: [email protected]
® USC
MADE IN THE
USAEST. 1952
COST SAVINGS
DRY UP TO 100 PAIRS OF HANDS FOR THE COST OF ONE PAPER TOWEL.
Our full line of virtually maintenance-free hand dryers save customers up to 98% of paper towel costs, providing a return on investment within months, all while protecting the environment.
Cost per 1,000 hand dryings
eXt series $0.18
$0.42
$23.44
gXt series
PAPER TOWEL