THE QU ILT SHOWN IS A DIGITAL REPRESENTATION. …BENATE LLC EST TH STEET TH FL NE YK NY T BENATECM...
Transcript of THE QU ILT SHOWN IS A DIGITAL REPRESENTATION. …BENATE LLC EST TH STEET TH FL NE YK NY T BENATECM...
-
© 2
016
Hei
di P
ride
mor
e B
enar
tex,
LLC
Uses Contempo’s Dino Age collection by Matthew Pridemore
Finished Size: 45” x 65”
What a cool way to use Matthew’s dinosaur panel! Some little boy or girl will be very lucky!
THE QUILT SHOWN IS A DIGITAL REPRESENTATION. ACTUAL FABRIC REPEATS WILL VARY FROM DESIGN SHOWN.
-
BENARTEX, LLC • 132 WEST 36TH STREET, 4TH FLOOR • NEW YORK, NY 10018 • T:212-840-3250 • WWW.BENARTEX.COM
SAMPLE KEY/SKU QTY CUT CUT PIECES VIA WOF
A
C
E
G
I
B
D
F
H
Blocks Panel4333-40 Green
Dino Skin4339-11 Gray
Dino Egg Dots 4337-13Gray
Dino Skin4339-05 Blue
Dino Egg Dots 4337-40 Green
Tossed Leaves 4334-40 Green
Dino Toss4335-70 Brown
Dino Skin4339-77 Dk. Brown
Tossed Leaves4334-78 Brown/Green
BLOCK ASSEMBLY PROJECT USES PRECISE 1/4” SEAMS. TEST YOUR SEAM ALLOWANCE BY CUTTING (2) 2-1/2” X 5” RECTANGLES. STITCH THEM TOGETHER ALONG THE 5” LENGTH. AT THE MIDPOINT, MEASURE ACROSS THE UNIT. IT SHOULD BE EXACTLY 4-1/2” WIDE. IF NOT, ADJUST YOUR SEAM ALLOWANCE AND REPEAT.
(1) 23-1/2” x 41-1/2” panel, FUSSY CUT
(2) 2” x 41-1/2” WOF strips.(2) 3” x 26-1/2” WOF strips.(3) 1-1/2” x WOF strips.*(2) 1-1/2” x 37-1/2” strips.
(2) 3-3/8” x WOF strips, sub-cut (16) 3-3/8” squares.
(3) 3-3/8” x WOF strips, sub-cut (32) 3-3/8” squares.
(1) 4-1/2” x WOF strip, sub-cut (4) 4-1/2” squares.
(2) 3-3/8” x WOF strips, sub-cut (16) 3-3/8” squares.
(16) 5-1/2” squares, each centered on a dinosaur, FUSSY CUT
(6) 2-1/2” x WOF strips, BINDING
(3) 4-1/2” x WOF strips.*(2) 4-1/2” x 37-1/2” strips.
* SEW STRIPS VIA SHORT ENDS THEN GO TO BORDER ASSEMBLY WOF/LOF=WIDTH/LENGTH OF FABRIC
Quilt Diagram
Note: If this Benartex pattern is included in a kit, any questions about the kit should be addressed to the vendor from whom you bought it.
1/4 yd
3/4 yd
1/2 yd
3/4 yd
1 panel
2/3 yd
1/4 yd
3/8 yd
1/4 yd
FINISHED SIZE: 45” X 65”
FINISHING Cut batting and backing 3” larger than top on all sides. Layer backing, batting and top together and baste or pin. When quilting is completed, trim excess batting and backing. Bind as usual.
C
C C
C
H
H
H H
I I
II
D D D D
D D D D
D
D
D
D
D
D
D
D
8. Sew (1) H 4-1/2” x (57-1/2”) strip to each sides of the quilt top. Sew (1) I 4-1/2” square to each end of (1) H 4-1/2” x (37-1/2”) strip. Repeat to make a second strip. Sew the strips to the top and to the bottom of the quilt top.
Blocks1. Sew (1) C 2” x 41-1/2” strip to each side of the A 23-1/2” x 41-1/2” panel. Sew (1) C 3” x 26-1/2” strip to the top and to the bottom of the A panel. Trim the block to measure 25-1/2” x 45-1/2” to make the Center Block.
Trim to measure 25 ½” x 45 ½”
after the borders are added
A
C
C
C C
2. Place (1) G 3-3/8” square on top of (1) B 3-3/8 square, right sides together. Draw a line across the diagonal of the top square. Sew 1/4” away from each side of the drawn diagonal line. Cut the (2) squares apart on the drawn diagonal line to make (2) BG units. Trim the units to measure 3” square. Repeat to make (32) BG units total.
GB
make 32
GE
make 32
G
G
G
GB
BEE
make 16
3. Repeat Step 2 using (16) E 3-3/8” squares and (16) G 3-3/8” squares to make (32) EG 3” units.
4. Sew (2) BG units and (2) EG units together to make (1) Pieced Block. Repeat to make (16) Pieced Blocks total.
Quilt Assembly5. Sew (5) Pieced Blocks and (4) D 5-1/2” squares together, alternating them, to make (1) strip. Repeat to make a second strip. Sew (1) strip to each side of the Center Block.
BORDER ASSEMBLY MEASURE WIDTH AND LENGTH OF THE QUILT TOP TO ENSURE C AND H BORDER SIZES, BELOW ARE OUR CUTTING SIZES.
6. Sew (4) D 5-1/2” squares and (3) Pieced Blocks together, alternating them, to make (1) strip. Repeat to make a second strip. Sew the strips to the top and to the bottom of the Center Block to make the quilt top.
7. Sew (1) C 1-1/2” x (55-1/2”) strip to each side of the quilt top. Sew (1) C 1-1/2” x (37-1/2”) strips to the top and bottom of quilt top.