THE NEW GENERATION CLEANER, SANITISER AND ANTIMICROBIAL PROTECTANT

THE BEST HAND SANITISER AND SURFACE PROTECTANT IN THE WORLD!

© Copyright 2010 ISO Technologies Ltd.

CONTENTS

Page

Introduction 3 How it works 4 Ingredients—Micro technology 5-6 New Generation Technology– (as reported by Dr. Gerba) 7 Germs are everywhere 8 Uses and application 9 Directions: How best to use 9-10 Comparisons of other products 10 Features and benefits 11 Frequently asked questions 11-12 How cost effective? 12 NZFSA accreditation 13 Tested and proven results from SGS 14 Preservative efficacy report by NZ Labs 15 MSDS 16

THE NEW GENERATION CLEANER, SANITISER AND ANTIMICROBIAL PROTECTANT, THE BEST IN THE WORLD.

© Copyright 2010 ISO Technologies Ltd. 3

4

WITHOUT ISOSHIELD

5

Many traditional competitive sanitisers use chemicals that act like poison which allows the possibility of the survival of bacteria, viruses, moulds, and other microbes, which then build immunity to these chemicals. This is effectively how superbugs and super viruses like Swine Flu, H1N1 and others evolve and develop. Although it is used in other competitive products, it is the revolutionary combination of ISOPROTECTANT™ Micro technology and other ingredients that give ISOSHIELD™ its unrivalled cleaning, sanitising and antimicrobial protection qualities. That same ISOPROTECTANT™ (Micro

technology) has EPA (Environmental Protection Agency USA) approvals and FDA (Federal Drug Administration USA) as one of the most effective, yet environmentally safe antimicrobial products. (see also Tested and Proven Results section) On application to surfaces, when dried, the chemical compound reacts to produce a bonded antimicrobial coating. On evaporation of the water or alcohol solvent, a durable bonded coating is produced which has sustained and soundly proven antimicrobial properties. This takes place at the tiniest level of molecular measurements and the whole process of creating the ISOPROTECTANT “SHIELD” is at microscopic levels—Micro-technology. This delivers far superior and longer lasting

effect of antibacterial protection and benefits

over all other traditional cleaning and sanitising

chemicals currently available in the market .

ISOPROTECTANT ™

MICROTECHNOLOGY

Long Chain of 18 x CH3 creates the spear

HOW THE ISOSHIELDTM PROTECTANT INGREDIENT WORKS

6

THE ISOPROTECTANTTM - ORGANOSILANE MOLECULE BONDS LIKE A

ROCK TO ANY SURFACE, PROVIDING LONG LASTING PROTECTION.

BACTERIA MICROBES ARE

IMPALED AND DESTROYED

BY THE ORGANOSILANE

MOLECULES

CHEMICAL STRUCTURE OF

ISOPROTECTANT TM

ORGANOSILANE

MOLECULE

Si

N

CH3

CH3

CH3

CH3

The Organosilane molecule is approximately 1 billionth of a meter in size and a small bacteria

microbe is approx 20 billionths of a meter, so as shown in diagram above bacteria is easily

impaled and destroyed by the closely bonded organosilane molecules

NEW TECHNOLOGY FROM AN OLD AND PROVEN CHEMICAL

One of the key ingredients in ISOSHIELDTM is from the organosilane family which was invented back in the 1950’s by DOW Chemicals and has evolved over the years to become one of the safest, non toxic antibacterial / antimicrobial products available today. It was originally used in war time to protect submarines from algae and mould growth allowing them to slip through the water without the drag of algae and mould slowing them down. Also used in the submarines air conditioning units to prevent listeria and other unwanted airborne diseases. That same micro-technology has evolved and now has EPA (Environmental Protection Agency USA) approval as one of the most effective, yet environmentally safest antimicrobial products

© Copyright 2010 ISO Technologies Ltd.

THE ISOPROTECTANT - ORGANOSILANE MOLECULE IS LIKE A SPEAR...

available. It is used in other competitive products to ISOSHIELDTM, such brands as Zoono, Bioshield, and Duraban, to name a few, but it is the new combination of other ingredients that give ISOSHIELDTM its unrivalled cleaning, sanitising and protective qualities.

There are literally hundreds of independent tests been undertaken by various companies over the years that prove beyond all doubt that the organosilane chemical (CAS27668-52-6) is a very safe and highly effective antimicrobial protectant.

ISOSHIELDTM is setting the new standard and creating a new generation, highly effective, yet eco friendly cleaner sanitiser and antimicrobial protectant product—3 in 1 , the best hand sanitiser and surface protectant in the world.

THE CHEMICAL MAKE UP OF THE

ORGANOSILANE MOLECULE

ATTRACTS THE BACTERIA

MICROBES

7

Dr. Gerba was at a recent seminar in Auckland on 20 July 2010 (hosted by Auckland Chamber of Commerce and Crest Commercial Cleaning) when he summarised the new generation of protectant sanitisers derived from organosilane technology.

Some of Dr. Gerba’s statements from the seminar— • “Desks are really bacteria cafeterias. They’re

breakfast buffets, lunch tables and snack bars, as we

spend more and more time at the office”

• “The average office desk has 400 times more

bacteria than a toilet seat”

• “The toilet seat contains a mere 49 germs per square

inch. The [office] telephone receiver has 25,000 and

the desk top 21,000 over the same area”

• “Good hygiene has prevented more disease than every vaccine and antibiotic ever invented. But

we’ve forgotten that lesson. We need to reinvent hygiene in the 21st century” • Hygiene in the workplace is a real issue according to Dr Gerba’s research showing that influenza

A viruses were detected in up to 50 per cent of workplaces and novo viruses found on over 20%

of surfaces throughout the day. His research in schools found that where proper standards of

hygiene were not maintained through the simple wiping with disinfectant wipes, school children

were 2.32 times more likely to report absenteeism due to illness.

• “Unfortunately New Zealand does not have any statistics on absenteeism or even statistics on

the causes of absenteeism,” commented Dr Gerba, who said “we can show that if companies

and schools followed relatively simple hygiene steps, then both ultimately see an increase in

profitability and productivity”

DR GERBA SUMMARISED THAT THE NEW GENERATION OF PROTRECTANT SANITISERS WILL BE DERIVED

FROM ORGANOSILANE TECHNOLOGY - WHICH IS ONE OF THE KEY INGREDIENTS IN THE VERY UNIQUE

FORMULATION OF ISOSHIELDTM

THESE ARE THE REAL REASONS WHY ISOSHIELDTM NEEDS TO BE ON EVERY DESK, IN EVERY OFFICE, HOME AND CAR AS A MEANS TO ASSIST IN KEEPING GERMS AT BAY.

NEW GENERATION TECHNOLOGY TO OVERCOME MODERN GERM WARFARE

Professor Charles Gerba

Dr Gerba, Environmental Microbiologist, at the University of

Arizona is an internationally recognised expert on the detec-

tion of bacteria and viruses and microbial risk assessment.

He is widely known as “Dr. Germ”

8

CLEANING

General Purpose Kitchen cleaner

Replace with ISOSHIELDTM

General Purpose Bathroom cleaner

Replace with ISOSHIELDTM

Heavy duty Oven cleaner, High strength acid toilet cleaner, General use liquid scourers (eg Jiff), Hard surface Floor Cleaner

Do NOT use ISOSHIELDTM as a specialised heavy duty cleaner

SANITISING / DISINFECTING

General disinfecting [i.e. external parts of toilet and hard surface bathroom areas (eg Dettol, Janola)]

Replace with ISOSHIELDTM

Hand Sanitising GEL (Alcohol based)

Replace with ISOSHIELDTM

Hand Sanitising GEL or Liquid (Non Alcohol based)

Replace with ISOSHIELDTM

ANTIMICROBIAL PROTECTING

ALL disinfectant and sanitising protection claimed products eg Dettol, Purell, Janola, Germ Free24 used regularly on hands and or high touch point areas such as Door handles, Benches, desks, phones, keyboards etc

Replace with ISOSHIELDTM

Specialist Antimicrobial Protection products such as Bioshield, Zoono, Duraban

Replace with ISOPROTECTANTTM (specialist services available) please email info.nz@pacifichygiene.com

USES AND APPLICATION FOR ISOSHIELDTM

SAVE TIME AND MONEY

REPLACE YOUR EVERYDAY GENERAL

CLEANERS, DISINFECTANTS, HAND

SANITISERS, AND

ANTIMICROBIAL PROTECTANT WITH

ISOSHIELD™ THE WORLDS BEST 3 IN 1.

9

DIRECTIONS HOW BEST TO USE ISOSHIELDTM

CLEANING, SANITISING AND PROTECTING

For hard surfaces • Spray surface area lightly, • then wipe down with a slightly dampened microfibre cloth (using 3-4 sprays of ISOSHIELDTM) to evenly dis-

perse, • then allow to dry for up to a minute. • For maximum effect do not rinse off*. For soft surfaces • Lightly spray surface area evenly to dampen • Then allow to dry off • If in doubt of colourfastness, please try a test area first. For Hand Sanitising • Simply spray 2 – 4 times to evenly wet your hands, • then gently rub hands together until they are dry. • No water or towels required*.

* NOTE When used in commercial food preparation and processing plants, it is an NZFSA requirement that food surfaces must be rinsed down with potable

water before production starts)

10

USES AND APPLICATION FOR ISOSHIELDTM ISOSHIELDTM can be safely applied to hard surfaces and fabrics in multiple commercial, industrial and domestic applications. ISOSHIELDTM is ideally and primarily designed for daily touch point areas such as bathrooms, toilets, door handles, hand rails, telephones, computer keyboards, office desks and environs plus numerous other touch points including of course YOUR HANDS as a hand cleaner and sanitiser on the go. HARD SURFACES to be applied to include (but not limited to): Painted surfaces of walls, ceilings, also desks, tables, wardrobes. Formica, stainless steel, plastics, porcelain, fibreglass, marble, synthetic marble and wet walled linings as in kitchens, bathrooms, offices, cool stores. SOFT SURFACES to be applied to include (but not limited to): Drapes and furnishings, mattresses, upholstery, shower curtains, shoes, socks and clothing fabrics, air conditioning filters where there is a requirement to protect against mould, moss, mildew, odours or bacteria. If in doubt of colourfastness then please try a sample area first.

COMPARISONS OF OTHER PRODUCTS TO ISOSHIELDTM

KEY FEATURES KEY BENEFITS

Contains 70% Ethyl alcohol – (from natural plant based sources and hospital grade quality) Uses Denatured ethyl alcohol

Kills 99% harmful bacteria (including campylobacter, E.coli, listeria, salmonella etc) at the recognised 70% strength.

Recognised and used extensively in hospitals and medical environments.

Mild cleaning and solvency properties to aid cleaning and sanitising

Like methylated spirits, makes the product unsafe to drink, eliminating abuse of alcohol content

Contains the common Quaternary ammonium compound, or SPECIFICALLY Benzylkonium Chloride ( base of majority of common household and commercial disinfectants)

Additional anti-bacterial, disinfectant, sanitising properties, helping to kill further harmful bacteria on contact.

Provides mild cleaning and surfactant qualities to assist cleaning

Contains a high quality Sugar based ester emulsifier and surfactant approved by FDA (This is an edible grade ingredient)

High quality surfactant and emulsifier to give excellent cleaning properties to aid in the removal of greases and fats.

Approved for use in food products so is safe to use on food surfaces.

Contains Organosilane approved by EPA and FDA. It creates a micro barrier of surface bonded particles that act as physical ‘spears’ to kill bacteria.

Proven anti-microbial that remains on surface when dried to provide high protection against recurring growth of bacteria

Safely provides ongoing protection against bacteria and germs. Proven effective against multiple viruses, bacteria, and germs

Unique manufacturing process creates technically superior product – Like no other.

A unique end product that sanitises, cleans, disinfects, and protects longer like no other.

FEATURES AND BENEFITS OF ISOSHIELDTM

FREQUENTLY ASKED QUESTIONS ON ISOSHIELDTM Is ISOSHIELD™ Green?

The ingredients in ISOSHIELDTM are all as environmentally friendly as we can choose for the desired end product. At this point in time like all other sanitisers and disinfectants that kill bacteria and germs it will never attain Enviro Choice or similar certification. The edible surfactant is eco certified and the organosilane is classified by the US EPA as Class IV antimicrobials – this is the safest classification that the EPA awards – the same rating as deionised water. The ethyl alcohol is obviously a volatile compound and is not eco friendly, although it is derived from natural sources and not petroleum based. Overall therefore it is as ‘green’ as we can make it given the very high quality product with the exceptional benefits that a true 3 in 1 can offer.

Is this a new chemical?

The combination and total formulation is new and very unique. While the individual ingredients are all well proven and been around a long time, the combination is new and unique because of the proprietary breakthrough in the special process of formulating the end ISOSHIELDTM product. What is the key differences between ISOSHIELD™ and other products on the market? 1. It is a genuine 3 in 1 cleaner, sanitiser and antimicrobial protectant.

2. It has 3 active ingredients for sanitising including 70% ethyl alcohol and benzylkonium chloride (one of the most

common sanitiser / disinfectants used in hundreds of products and generally they use only ONE active ingredient). These 2 ingredients provide the instant and short term broad spectrum killing of bacteria and viruses and In

11

What types of bacteria is ISOSHIELD™ effective against? ISOSHIELD™ is effective against nearly all bacteria, plus fungus, algae, and mould. A representative list of microbes against which ISOSHIELD™ has been tested by many independent accredited authorities many of which can be viewed on the EPA website along with many others. It is the proven records of the respective ingredients that give assurance of a safe and proven record of superior antimicrobial protection. Can ISOSHIELD™ be washed off? No. ISOSHIELD™ forms a permanent bond to most surfaces and cannot be washed off or leach into the environment. Over time and with abrasive rubbing, it will eventually lose it’s bond and this obviously depends on the frequency of abrasion or rubbing. Will this technology adversely affect the skin or environment? No. Since the antimicrobial is permanently bound to the surfaces it protects, it does not leach from surfaces applied too including skin or into the environment. Extensive toxicological testing shows the antimicrobial does not cross the skin barrier. How long will it last on my hands? ISOSHIELD™ on average can be expected to last between 8 and 12 hand washes because of the frequent abrasive rubbing of hands. Naturally you need to wash your hands in the normal manner at normal times. Normal washing can of course be substituted with using ISOSHIELD™ instead if you are ‘on the go’ and not near washing facilities. Does ISOSHIELD™ give off gases or fumes after application? Alcohol sanitisers have been around and extensively used for decades. Because of the ethyl alcohol content there is about 15 – 30 seconds immediately after application as the alcohol evaporates that may give off some fumes. This is quite normal and in ordinary circumstances and use, does not cause any problem at all. For the organosilane ingredient, the chemistry polymerizes where it is applied and forms a permanent bond that typically lasts for the life of the treated surface and gives off no fume or gas. Normal cleaning should not remove the treatment; although it can be abraded away. How long does the ISOSHIELD™ last on other surfaces? Over time and with abrasive rubbing, it will eventually loose it’s bond and this obviously depends on the frequency of abrasion or rubbing. Therefore if the surface is aggressively rubbed or used extensively (e.g. a high use entrance doorway) then daily or twice daily application may be required. However a surface that is not touched or rubbed (e.g. a kitchen cupboard or wall) then it may well be protected and last for months. Rubbing and abrasion is what effectively determines the life span before reapplication is required Is there a test method to determine if ISOSHIELD™ is present? Yes. ISOSHIELD™ is based on an active ingredient that, in most cases, can be easily detected. A simple method of detection is available to demonstrate the presence or absence of the treatment. Bromophenol Blue (BPB) stain testing clearly shows the presence of ISOSHIELD™ in a matter of minutes. In addition antimicrobial testing can detect the presence of bacteria on a surface but this would not show presence or otherwise of ISOSHIELD™ residue, whereas the BPB test directly shows the presence of ISOSHIELDTM What tests show that the growth of bacteria has been prevented? Microbiological testing is what establishes the baseline standard that is used. Iso Technologies have commissioned independent tests from independent authorities, SGS and also NZ Labs (who are accredited to Medsafe NZ) There are many independent test results available to show substantial broad spectrum protection against many gram positive and gram negative bacteria in addition to moulds, fungi’s and viruses.

HOW COST EFFECTIVE IS ISOSHIELDTM COST PER SPRAY

Size RRP Sprays per bottle Cost per Spray

50ml $6.99 350 < 2 cents

250ml $13.80 1750 < 0.8 cents

500ml $20.45 800 < 2.5 cents

12

13

NZFSA ACCREDITATION — WHAT IT MEANS

NZFSA (NZ Food Safety Authority) is the authority for accrediting various classifications of products to specific and approved applications. For meat and dairy the specs or standards required are in the NZFSA and surpass the old ‘MAF Approved’ standards – essentially the same but accredited by uni-form department of NZFSA which now approves all food related products and standards including dairy and meat. The correct code must be accredited for a specific product to be used in a commercial food preparation or processing factory.

ISOSHIELDTM IS50 AND IS250 both comply

and have accredited approval under NZFSA

section 5.3 Cleaners approved code C32 and

under section 5.5 Topical Products approved

code C52. (approval letters pictured)

This FRAGRANCED formula is ideal for all personal, domestic, office and general applications

NON FRAGRANCED formula and packaging designed for professional commercial use in

commercial food production, preparation and processing facilities

ISOSHIELD - NZFSA MOST ACCREDITED PRODUCT ISOSHIELD 500 has more approvals under various NZFSA codes than any other individual product on the market, which means it is the most versatile cleaning and sanitising product available for use in the food industry. Every commercial kitchen should have it! ISOSHIELDTM 500 is the NON fragranced version of ISOSHIELDTM and as such is suited to

Food Preparation and processing applications. IS500 complies to;

♦ NZFSA Section 5.5 Topical Preparation1 (for hand washing and sanitising), compliance

and approval to Codes C51 and the imbedded codes C56 and C52.

♦ NZFSA Section 5.4 Sanitisers (for all surface sanitising), compliance and approval to

Code C41.

♦ NZFSA Section 5.3 Cleaners (for all surface cleaning), compliance and approval to Code

C38 and the embedded code C31, C32 and C34

(See Directions for Use section for correct use and application in accordance with NZFSA regulations)

Note1 For Topical preparations accreditation for ISOSHIELD see also NZ Labs report and certification for ISOSHIELD

certified to BP 2009 (British Pharmaceutical 2009) international standards certified.

(26 March 2010 through 4 May 2010) Products tested: ISOSHIELDTM Formula variants ISOSHIELDTM181209A and ISOSHIELDTM

160210A Challenge Bacteria, Mould and Yeast strains tested:

E.coli, Pseudomonas aeruginosa, Enterococcus faecalis, Salmonella menston, Staphylococcus aureus, Candida albicans (yeast) Aspergillus spp (mould)

Process & Protocol:

Flat surface plastic containers with lids were chosen to contain each testing sample in a laboratory setting. The inner surface of these containers were swabbed with a heavy inoculums of the challenge bacteria above. Before the surface is completely dried spraying each with the ISOSHIELDTM product samples as you would expect your customers to clean any surface. Additional challenge of all above bacteria strains (1-7) to be re-introduced at each test point.

Testing timeframes:

The containers will then be swabbed at different intervals in addition to re-introducing the challenge bacteria at each test point: On application (Day 1) Day 3 after application Day 7 after application Day 14 after application Day 21 after application The swabs at each time interval will be tested for the presence or survival of bacteria.

Results reporting:

The results of the swabs taken will be reported as: “No growth” “light growth” “medium growth” “heavy growth”. (It is very difficult to compare counts of the bacteria after such a test, so we cannot report exact numbers).

REPORTED TEST RESULTS:

ISOSHIELD 181209A

ID # 1 - Day 1 test (2 hours of application) = No

Growth

ID # 6 - Day 3 test = No Growth ID # 11 - Day 7 test = No Growth ID # 16 - Day 14 test = No Growth ID # 21 - Day 21 test = No Growth

ISOSHIELD 160210A

ID # 2 - Day 1 test (2 hours of application) = No

Growth

ID # 7 - Day 3 test = No Growth ID # 12 - Day 7 test = No Growth ID # 17 - Day 14 test = No Growth ID # 22 - Day 21 test = No Growth

*CONCLUSIONS OF ISOSHIELD SGS

CHALLENGE TEST

When ISOSHIELDTM is sprayed on to a surface and challenged with bacteria and mould strains [including E.coli, Pseudomonas aeruginosa, Enterococcus faecalis, Salmonella menston, (Food Poisoning) Staphylococcus aureus, (MRSA) Candida albicans (yeast) and Aspergillus spp (Black Mould)], it can reportedly be believed that the surface will be protected from germ and bacteria re growth for no less than 21 days. H1N1 and Norovirus are included in the groups of bacteria and virus that Isoshield will kill. *SGS Analysis Report 37177A dated 4 May 2010 to

Iso Technologies Ltd. shows results of testing only

(NO process or protocol details) and the summary

information above including the products, protocol,

time frames and results reporting are documented

here to provide a more concise informative brief as

to the test parameters from which the above

conclusion is drawn. The SGS analysis report is

subject to copyright and is not available for

reproduction and the “reported test results” are

derived directly from the 37177A report.

TESTED AND PROVEN RESULTS FROM SGS TESTING

14

This Preservative Efficacy test was undertaken by NZ Labs in May 2010. This “Preservative Efficacy Report” relates to internationally recognised testing protocol as set down by British Pharmacopoeia (BP). In summary, ISOSHIELDTM complies to the international

standards of efficacy to the highest British

Pharmacopoeia 2009 standards for topical products.

These standards are internationally recognised and are

used as a benchmark extensively by health departments,

pharmacy and medical associated entities to measure

and ensure efficacy of products to meet the high

standards of the British Pharmacopoeia.

THIS MEANS THAT ISOSHIELDTM IS SAFE TO USE AND THAT USERS CAN BE ASSURED THAT ISOSHIELDTM IS OF A PHARMACEUTICAL STANDARD FOR TOPICAL PRODUCTS. About BP 2009 The British Pharmacopoeia (BP) 2009, published August 2008, is the authoritative collection of standards for UK medicinal substances and the official source of UK pharmaceutical quality standards. The BP contains monographs, which set out the mandatory standards for active substances, excipients and formulated preparations, together with General Notices, Appendices (test methods, reagents, etc) and Reference Spectra. Detailed information and guidance on various aspects of current pharmacopoeia policy and practice are provided in the Supplementary Chapters of the BP.

PRESERVATIVE EFFICACY REPORT

15

SAFETY DATA SHEET

SECTION 1: IDENTIFICATION OF THE SUBSTANCE AND SUPPLIER

Product name: ISOSHIELD

Product code: IS50, IS250

Recommended use: ISOSHIELD is a multi-application cleaner, sanitiser and antimicrobial protectant, 3-in-1 product suitable for application to hands and hard and soft surfaces as per directions.

Company details: ISO TECHNOLOGIES LTD

P O BOX 305-503

Triton Plaza, North Shore

Auckland 0757, NEW ZEALAND

Telephone number: Phone: +64 9 477-5700 Fax: +64 9 476-3602

Emergency telephone number: National Poisons Centre: 0800 764 766 (0800 POISON)

Fire Service, Ambulance: Dial 111

Date of preparation: 25 AUGUST 2010

SECTION 2: PRODUCT COMPOSITION AND INGREDIENTS

Product Characterisation: Colourless Clear Liquid, Cleaning Sanitising and Antimicrobial Protectant Solution

INGREDIENT CAS # APPROX CONCENTRATION

ETHYL ALCOHOL 64-17-5 ~70%

BENZYLKONIUM

CHLORIDE

61789-71-1 <2 %

Octadecyldimethyl

(3-

Trimethoxysilylpro

pyl) Ammonium

Chloride

27668-52-6 <1 %

EDIBLE SUCROSE

ESTER SURFACTANT;

Proprietary <5 %

Aqua pura - Water 7732-18-5 >20 %

Fragrance Proprietary < 0.5%

Product Components:

Data and interpretation: May be harmful if swallowed. May cause eye irritation

SECTION 3: HAZARDS IDENTIFICATION

Hazard classifications: 3.1B FLAMMABLE

Classified as hazardous according to NOHSC – HAZARDOUS SUBSTANCE

Priority and secondary identifiers: Ecotoxic see section 11

Risk and safety phrases: Harmful – May cause eye irritation. Avoid contact with eyes and ensure adequate

ventilation when using.

Harmful – May cause organ damage from repeated oral exposure at high doses .

Harmful to aquatic life with long-lasting effects. Avoid contamination of any water

supply with product.

SECTION 4: FIRST AID MEASURES

Necessary first aid measures: For advice contact the National Poisons Centre 0800 POISON (0800 764

766) or a doctor immediately

Eye Contact: Flush eyes with plenty of water for 15 minutes holding eyelids open if

necessary. Seek medical assistance.

Skin Contact: Not applicable. No irritation or reaction expected.

Excessive Inhalation: Remove patient to fresh air. Lie down and keep warm and

rested. Seek medical assistance.

Ingestion: Do NOT induce vomiting. Seek medical assistance immediately.

Workplace facilities: Facilities storing or utilising this material should be equipped with an eyewash facility

Notes for medical personnel: Treat symptomatically

SECTION 5: FIRE FIGHTING MEASURES

16

Type of hazard: FLAMMABLE.

Fire hazard Information: Containers can build up pressure if exposed to heat and/or fire. As in any fire, wear a

self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. Vapours may form an explosive mixture with air.

Vapours can travel to a source of ignition and flash back. Will burn if involved in a fire.

Flammable Liquid. Can release vapours that form explosive mixtures at temperatures

above the flashpoint. Use water spray to keep fire-exposed containers cool. Containers

may explode in the heat of a fire.

Flash Point: 30oC

Extinguishing media and methods: For small fires, use dry chemical, carbon dioxide, water spray or alcohol-resistant

foam. For large fires, use water spray, fog, or alcohol-resistant foam. Use water spray

to cool fire-exposed containers. Water may be ineffective. Do NOT use straight

streams of water.

Hazchem code: 3.1

Recommended protective clothing: Wear PVC protective clothing and breathing apparatus for fire fighting if necessary.

SECTION 6: ACCIDENTAL RELEASE MEASURES

Emergency procedures: Wear protective clothing. Clear area of unprotected personnel. Contain spill and absorb with sand, soil or absorbent granules. Do not allow product or washings to enter the

waterways or sewer. If spill does enter waterways contact the local authority. Collect

in an appropriate sealable container for disposal in an approved landfill.

SECTION 7: HANDLING AND STORAGE

Handling procedures:

Use only in a well-ventilated area. Ground and bond containers when transferring material. Use spark-proof tools and explosion proof equipment. Avoid contact with

eyes. Avoid contact with heat, sparks and flame. Avoid ingestion and inhalation.

Storage procedures: Keep away from heat, sparks, and flame. Keep away from sources of ignition. Store in

a tightly closed container. Keep from contact with oxidizing materials. Store in a cool,

dry, well-ventilated area away from incompatible substances.

SECTION 8: EXPOSURE CONTROL/PERSONAL PROTECTION

Workplace exposure standards: No exposure limits have been specifically assigned for this product.

Application in the workplace: As instructed in directions product can be used in the workplace as directed

Engineering controls: An adequate supply of water should be available in storage and handling areas.

Facilities storing or utilising this material should be equipped with an eyewash

facility.

Personal protection: Avoid excessive contact. Wash contaminated clothing before storage or reuse.

Product can be used as cleaner and sanitiser as directed after handling and before

eating, drinking or smoking.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Physical State: Colourless clear liquid.

Odour: A fresh and pleasant scented fragrance

Solubility in Water Soluble in water

Specific Gravity ~0.869g/mL @ 20°C

Boiling Point 78OC

Flash Point 30OC

Viscosity Data Not available at published date

Molecular weight Data Not available at published date

pH Data Not available at published date

SECTION 10: STABILITY AND REACTIVITY

Stability of the substance: Stable product under normal conditions, temperatures and pressures

Conditions to avoid: Incompatible materials, ignition sources, excess heat, oxidizers

Material to avoid: Do not mix with any other liquid other than water. Avoid anionic materials.

Hazardous decomposition products: Carbon monoxide, irritating and toxic fumes and gases, carbon dioxide, silicon

dioxide.

Hazardous polymerization: Will not occur

Specific data: N/A at time of published date

17

SECTION 11: TOXICOLOGICAL INFORMATION

Summaries Data: Colourless Clear Liquid, Cleaning Sanitising and Antimicrobial Protectant Solution

INGREDIENT CAS # Toxicological Summary

ETHYL ALCOHOL 64-17-5 Medium toxicity. Not classifiable as carcinogenic to

humans – toxic to bacteria

BENZYLKONIUM

CHLORIDE

61789-71-1 Low – medium toxicity. Not known as carcinogenic to

humans – toxic to bacteria

Octadecyldimethyl

(3-

Trimethoxysilylpro

pyl) Ammonium

Chloride

27668-52-6 Very low toxicity and Not known as carcinogenic – toxic

to bacteria

EDIBLE SUCROSE

ESTER SURFACTANT;

Proprietary N/A

Aqua pura - Water 7732-18-5 N/A

Fragrance Proprietary N/A

Product Components:

Effects of Acute Exposure: Eye Contact: content could cause permanent damage.

Skin Contact: No health effects expected.

Inhalation: If mists or vapour inhaled, could cause irritation due to ethanol content.

Ingestion: Harmful. Burning pain in mouth and throat and oesophagus.

Other Health Effects: Some individuals may be sensitive to this product.

Effects Of Chronic Exposure: None Known

SECTION 12: ENVIRONMENTAL INFORMATION

Potential environmental interactions: Harmful to fish. Do not contaminate drains or waterways

Environmental Risk & Safety : N/A at time of published date

SECTION 13: DISPOSAL CONSIDERATIONS

Recycle container in accordance with local

bylaws where possible.

Product Disposal: To avoid disposal all attempts should be made to utilise the

product completely in accordance with its registered use. Prevent the product from

entering natural water sources.

Container Disposal: Burn empty container if wind direction permits, otherwise bury

in a suitable landfill.

SECTION 14: TRANSPORT INFORMATION

Relevant Information: Falls within HSNO Classification 3 as Flammable liquid.

Special provisions for transport not available at published time and date.

SECTION 15: REGULATORY INFORMATION

Labelling Information (EEC Regulations Safety

Phrases as per label):

S2 Keep out of reach of children

S26 In case of contact with eyes, rinse immediately with plenty of water and seek

medical advice

S46 If swallowed, wash out mouth, then drink plenty of water. Seek medical advice

immediately and show the container label.

HSNO controls: Refer Section 3

NZFSA controls: NZFSA (New Zealand Food Safety Authority) Approved to code C32 and C52 - All animal products except dairy

Preservative Efficacy: Complies to International guidelines laid out for BP2009 Preservative Efficacy as

documented accession No. 10N016452

SECTION 16: OTHER INFORMATION

Additional Information For product information visit the www.isoshield.com website.

While the information set forth is believed to be accurate as of the date hereof, ISO

TECHNOLOGIES LTD. makes no warranty with respect hereto and disclaims all

liability from reliance thereon

Revision Number and Date: Original Date of Preparation 20 June 2010

This amended version (V2) dated 25 August 2010

18

AUCKLAND Head Office: PO Box 305 503 Triton Plaza, North Harbour p 09 477 5700 f 09 476 3602 support 0800 354 800 free fax 0800 367 947 info.nz@pacifichygiene.com www.pacifichygiene.com

HAMILTON m 021 674 793 email: simon.biss@pacifichygiene.com

CHRISTCHURCH

PO Box 7104

p 03 331 7760

f 03 331 7761

m 021 674 768

email: mark.thompson@pacifichygiene.com

WELLINGTON

m 021 674 752

email: philip.anderson@pacifichygiene.com

www.ISOSHIELD.com

ISOSHIELDTM IS PROUDLY DISTRIBUTED IN NEW ZEALAND BY

12 October 2010

AUCKLAND m 021 674 757 email: margery.pryor@pacifichygiene.com m 021 67 4753 email: david.hellyer@pacifichygiene.com