The new CF Grade Family - Sadot S.Y · 2015. 5. 25. · H60S with low KIC values (fracture...
Transcript of The new CF Grade Family - Sadot S.Y · 2015. 5. 25. · H60S with low KIC values (fracture...
InnovatIon
En
thE nEw CF GradE FamIly
En
2
The
New
CF
Gra
de F
amil
yCo
rro
sIo
n-rE
sIst
ant
Gra
dEs
The New CF Grade FamilyCorrosIon-rEsIstant GradEs
Product code CF-s18Z CF-h25s CF-h40sCtEB00 wEdm blocks, as sintered upon request in stock in stockCtEB20 wEdm blocks, thickness ground in stock in stock in stockCtss strips for punching dies in stock upon request in stockCtsB Bushings for guides and dies in stock upon request in stockCtPP rods for powder compaction dies upon request upon request in stockCtrr rods for punching dies, as sintered in stock upon request in stockCtrG rods for punching dies, diameter ground in stock upon request in stock
Grades available in stock and via e-Techstore within 24 hours:
Corrosion resistant gradesCF-S18Z – Increased fracture toughness allows the usage of a submicron grade for applications where high bending forces occur.
CF-h25S – Fine-medium grade with high hardness and fracture toughness for high requirements regarding abrasive wear.
CF-h40S – the grade for universal application, ideal compromise between hardness and fracture toughness.
CF-F35Z – Fine-medium grade especially designed for bending, blanking and forming applications.
CF-20hP – medium-coarse grade combining the hardness of a fine grade with the fracture toughness of a coarse grade.
CTeB00 CTeB20 CTSS CTPP
CTSB CTrr CTrG
type CF-s18Z CF-h25s CF-h40s CF-F35Z CF-20hP*special blocks ● ● ● ● ●
special blocks with start bore / steel plug / threaded hole ● ● ● ●
Preforms according to customer drawing ● ● ● ●
Preforms to customer drawing with steel plug/thread ● ● ● ●
The following grades are available as special versions:
* all types of CF-20hP can be produced starting september 2014
3
CF-S18ZBinder content 9.0 %Grain size submicronCorrosion resistance yeShardness [hv10] 1610transverse rupture strength [mPa] 3500Fracture toughness [mPa*m^1/2] 11.0
CF-h25SBinder content 8.5 %Grain size fine-mediumCorrosion resistance yeShardness [hv10] 1660transverse rupture strength [mPa] 2600Fracture toughness [mPa*m^1/2] 10.1
CF-h40SBinder content 12.0 %Grain size fine-mediumCorrosion resistance yeShardness [hv10] 1400transverse rupture strength [mPa] 3000Fracture toughness [mPa*m^1/2] 12.0
CF-F35ZBinder content 17.5 %Grain size fine-mediumCorrosion resistance yeShardness [hv10] 1150transverse rupture strength [mPa] 3300Fracture toughness [mPa*m^1/2] >15.0
CF-20hPBinder content 10.0 %Grain size medium-coarseCorrosion resistance yeShardness [hv10] 1300transverse rupture strength [mPa] 2800Fracture toughness [mPa*m^1/2] >15.0
evolution for higher performance
mG18 / Cts20l tsm3310.0 % 10.0 %
submicron submicronno no
1680 16103700 37009.4 9.4
h20s / CtF12 h30s / CtF186.0 % 9.0 %fine fineno no
1640 14002200 28009.9 10.9
h30s / CtF18 h40s / CtF249.0 % 12.0 %fine fineno no
1400 13302800 300010.9 12.0
h50s / CtF30 h60s / CtF4015.0 % 20.0 %
fine fineno no
1240 10703100 340013.1 14.2
B30s / CtC20 B40s / CtC2510.0 % 12.5 %coarse coarse
no no1170 10803000 305013.1 16.3
New grade replaces old grades
The
New
CF
Gra
de F
amil
yCo
rro
sIo
n-rE
sIst
ant
Gra
dEs
The New CF Grade FamilyCorrosIon-rEsIstant GradEs
4
areas of application
The
New
CF
Gra
de F
amil
yar
Eas
oF
aPPl
ICat
Ion
→ ReplacessubmicrongradessuchasMG18/TSM33(Cts20l) when there are corrosion issues or edge chipping
→ ReplacessubmicrongradessuchasH30S/H40Swhenthere is insufficient transverse rupture strength and wear
→ AlternativetoCF-H25S&CF-H40Sincaseofinsufficienttransverse rupture strength
CF-S18ZCorrosion-resistant submicron grade with increased fracture toughness
० Particularlyforthin-walledpunchesanddieswithdelicate shapes which require high transverse rupture strength
० Whenhighwearresistanceingeneralandhighwearresistance of the skin surface are required
० Formaterialswithahightendencytoadhesion
० Forsoftmaterials,suchascopperalloys, e.g. Cusn4F54, CuZn37, Cuni9sn2
Application
→ ReplacesfineandmediumgradessuchasH30S/H40S/CF-h40s when there are issues with excessive wear
→ AlternativetoCF-H40Sincaseofadhesion
CF-h25SCorrosion-resistant fine-medium grade with high hardness
० Whenmaximumwearresistanceingeneralandin particular of the skin surface are required
Application
→ Replacesstandardfine-mediumgradessuchasH30S/h40s/h50s when there are problems with wear and corrosion
→ ReplacesstandardsubmicrongradessuchasTSM33/Cts20l when there are problems with edge chipping or corrosion
→ AlternativetoCF-H25Sincaseofprimaryedgechipping
CF-h40Swell-balanced corrosion-resistant fine-medium grade
० IdealcompromisebetweenwearresistanceandKIC-value (fracture toughness / edge stability)
० Foruniversalapplications:stamping,bending,blanking and forming operations
Application
The New CF Grade FamilyarEas oF aPPlICatIon
5
The
New
CF
Gra
de F
amil
yar
Eas
oF
aPPl
ICat
Ion
→ ReplacesHSS/PMsteelsinwearorcorrosionsituations
→ Replacesfine-mediumgradessuchasH40S/H50S/H60SwithlowKICvalues(fracturetoughness,edgestability) when there are problems with edge chipping
→ ReplacesH50S&H60Sasavariantwithprotectionagainst corrosion
→ AlternativetoCF-20HPincaseofbreakageissuesoredge chipping
→ Showsverygoodresultsinthemillingprocessregardingsurface and economy
CF-F35ZCorrosion-resistant fine-medium grade with high fracture toughness
० Stampingofthicksheetmetal
० Stampingofhigh-tensilestripmaterial
० Bending&formingapplications
Application
→ ReplacesHSS/PMsteelsandcarbidecoarsegrainsincase of wear or corrosion issues
→ Replacesfine-mediumgraingradessuchasH40S/H50Swhen there are problems with edge chipping
→ AlternativetoCF-F35Zwhenthebindercontentistoohigh for the application (e.g. adhesion)
CF-20hPCorrosion-resistant medium-coarse grade with high hardness
० CharacterisedbyhighhardnessandamaximumKIC value (fracture toughness, edge stability)
० HardnessofafinegraingradeandKIC value of a coarse grain grade
० Stampingofthicksheetmetal
० Bendingandformingapplications
Application
The New CF Grade FamilyarEas oF aPPlICatIon
6
1)
2)
3)4)
5)
application matrix for the tool and die industrymin requirements regarding the surface quality* max
requ
irem
ents
rega
rdin
g th
e su
rface
qua
lity*
max
min
० Insufficientdata.Testcanbecarriedoutuponrequest.
* minimal damage due to machining operation (formation of thermal cracks, white zone, ...) and low roughness values. adhesion due to ribbon material requires the best possible surface quality.
Optimisation of applicationstool improvement is the basis for maximum economy in the application process. CEratIZIt offers a systematic approach for the optimisation of the overall system. this includes both an application-specific grade selection
and the possibility to optimise the machining strategies in the production process in order to ensure sustainable development for other applications.
The
New
CF
Gra
de F
amil
yeaP
PlIC
atIo
n m
atrI
X
Tensile strength (N/mm2)
Strip thickness (mm) < 500 500 – 900 900 – 1400 1400 – 2000 < 2000
< 0.2 CF-/CF-s18Z CF-h25s/CF-s18Z CF-h25s/CF-s18Z CF-s18Z/CF-h40s CF-F35Z/CF-20hP
0.2 – 0.5 CF-h25s/CF-s18Z CF-h25s/CF-s18Z CF-h25s/CF-s18Z CF-h40s/CF-20hP CF-F35Z/CF-20hP
0.5 – 0.8 CF-h25s/CF-s18Z CF-s18Z/CF-h40s CF-s18Z/CF-h40s CF-F35Z/CF-20hP ०
0.8 – 1.2 CF-s18Z/CF-h40s CF-h40s CF-h40s CF-F35Z/CF-20hP ०
1.2 – 1.5 CF-h40s CF-h40s CF-h40s/CF-20hP CF-F35Z/CF-20hP ०
1.5 – 2 CF-h40s CF-h40s/CF-20hP CF-F35Z/CF-20hP ० ०
2 – 3 CF-h40s CF-h40s/CF-20hP CF-F35Z/CF-20hP ० ०
3 – 6 CF-h40s/CF-20hP CF-F35Z/CF-20hP ० ० ०
6 – 10 CF-F35Z/CF-20hP ० ० ० –
> 10 ० ० ० – –
analysis of the active part (punch, die). determination of the primary cause of wear (adhesion, edge chipping ...)
occurring problem
Potential to use data for other applications
Joint analysis and assessment of performance
recommendation of the optimal carbide grade and suggestions for process optimisation
The New CF Grade FamilyaPPlICatIon matrIX
7
NOTe
S
NOTeS
Tensile strength (N/mm2)
Strip thickness (mm) < 500 500 – 900 900 – 1400 1400 – 2000 < 2000
< 0.2 CF-/CF-s18Z CF-h25s/CF-s18Z CF-h25s/CF-s18Z CF-s18Z/CF-h40s CF-F35Z/CF-20hP
0.2 – 0.5 CF-h25s/CF-s18Z CF-h25s/CF-s18Z CF-h25s/CF-s18Z CF-h40s/CF-20hP CF-F35Z/CF-20hP
0.5 – 0.8 CF-h25s/CF-s18Z CF-s18Z/CF-h40s CF-s18Z/CF-h40s CF-F35Z/CF-20hP ०
0.8 – 1.2 CF-s18Z/CF-h40s CF-h40s CF-h40s CF-F35Z/CF-20hP ०
1.2 – 1.5 CF-h40s CF-h40s CF-h40s/CF-20hP CF-F35Z/CF-20hP ०
1.5 – 2 CF-h40s CF-h40s/CF-20hP CF-F35Z/CF-20hP ० ०
2 – 3 CF-h40s CF-h40s/CF-20hP CF-F35Z/CF-20hP ० ०
3 – 6 CF-h40s/CF-20hP CF-F35Z/CF-20hP ० ० ०
6 – 10 CF-F35Z/CF-20hP ० ० ० –
> 10 ० ० ० – –
we
rese
rve
the
right
to m
ake
tech
nica
l ch
ange
s fo
r im
prov
emen
t of t
he p
rodu
ct.
7002757ma-Pro-0612-En-05/14-sP
Parent company in luxembourg
CEratIZIt luxembourg s. à. r. l.route de holzem 101l-8232 mamerTel.: +352312085-1Fax +352311911E-mail: [email protected]
Contact for further information
CEratIZIt deutschland Gmbhrobert-Bosch-straße 23d-72186 EmpfingenTel.: +497485998020Fax: +49748599802220E-mail: [email protected]