THE INTERNATIONAL CATALOG · See other applications under ASTM D 850 - D 1078 SCOPE This test...

1

CN06-2uk (all previous editions obsolete)

THE INTERNATIONAL CATALOG

2


ASTM D 5 Penetration of Bitumous Material

picture not mandatory


941731 - MANUAL PENETROMETER

941734 - AUTOMATIC PENETROMETER


9417582 - GREASE WORKER


941736 - OUTFIT FOR LUBRICATING GREASE


941810 - OUTFIT FOR BITUMEN

See other applications under ASTM D 217 - D 937 - D 1321 - D 1403

SCOPEThis test method covers the determination of the penetration of semi-solidand solid bitumous materials.

OTHER STANDARDSIP 49 - NFT 66004 - ISO 3997 - DIN 52010

REF. 941734This compact automated instrument uses the latest electronic technolo-gies. It is equipped with keyboard, LCD display, user friendly software andstepper motor for penetration depth as low as 0.01 mm, needle (or cone)holder, magnifying lens and low voltage illuminator, centering guide, RS232Coutput and accessories for automatic level detection for conductive sam-ples.

REF. 941731This manual penetrometer includes a large table on levelling feet with spiritlevel, a manual release mechanism and a dial indicator in 0.1 mm.Outfit (needle, holder, sample container, ...) not included.

REF. 9417582This compact twin-unit automated grease worker uses electronic counterto control the strokes number and is delivered with 2 cups and 2thermometers. Supply 400V 3ph .

ACCESSORIES (for all standards)

BITUMEN ACCESSORIES (for D5)

outfit is needle + holder + weight 50g + 2 containers

LUBRICATING GREASES ACCESSORIES (for D217)

outfit is cone + holder + container

941759 Plunger plate ASTM (51 holes)

11504 ASTM thermometer 17C11532 ASTM thermometer 63C11533 ASTM thermometer 64C

518063 Standard needle 2.5 g (up to 350 u.)

941732 Calibration kit for automatic penetrometer

941737 Holder 47.5 g941810 Outf it for penetration of bitumous material941812 Additional w eight 100 g941815 Additional w eight 50 g9418140 Long needle 2.5 g (up to 500 u.)21712 Sample container one use 55x35 mm (pack of 300)

9418181 Sample container A l. 55x70 mm (>200 u.) 9418191 Sample container A l. 55x57 mm (up to 500 u.)9417371 Bitumen automatic level detection device

941739 Grease cutter w ith blade941736 Outf it for consistency of lubricating grease941737 Holder 47.5 g941738 Standard cone 102.5 g941750 Hand grease w orker w ith cup and thermometer941751 Worker cup only

941760 Plunger plate Fed. Spec. (270 holes)9417411 Sample container 76x63 mm 9410759 Thermometer for grease w orker27322 Spatula 30x200 mm

230 V1 A50 Hz23 Kgw 260 mmd 320 mmh 540 mmon request115V 60Hz

5.6 Kgw 180 mmd 180 mmh 560 mm

400/3ph V3 A50 Hz29 Kgw 400 mmd 260 mmh 500 mm

518066 Sample container A luminium 55x35 mm

27794 Water bath model RE 112 (max.100°C)

3


ACCESSORIES (for D937)

outfit is cone + container + holder


outfit is shouldered needle + container + weight + holder


SPARE PARTS FOR ALL MODELS

ASTM D 6 Loss on Heating of Oil and AsphalticCompounds

SCOPEThis test method covers the determination of the loss in mass (exclusive ofwater) of oil and asphaltic compounds when heated.

OTHER STANDARDSIP 45 - NFT 66011

REF. 941875Strictly conform to ASTM requirements because of exclusive thermocou-ple sensor installed on the rotating shelf with the control thermometer, thisis a double wall illuminated oven with glass window, 9 place revolving shelf,9 aluminium containers, thermometer and instruction manual.

ACCESSORY

SPARE PARTS


941875 - REVOLVING-SHELF OVEN


941811 - OUTFIT FOR PETROLEUM WAXES


941735 - OUTFIT FOR PETROLATUM

941738 Standard cone 102.5 g

941735 Outf it for consistency of petrolatum941737 Holder 47.5 g

9417412 Sample container 100x65 mm w ith cover

941816 Needle w ith shoulder 2.5 g941737 Holder 47.5 g941811 Outf it for consistency of petroleum w axes941815 Additional w eight 50 g941820 Sample container w ith base plate

941742 ¼ scale cone and plunger (9,38 g)941743 ½ scale cone and plunger (37,5 g)9417421 ¼ scale grease w orker (manual operation)9417431 ½ scale grease w orker (manual operation)27322 Spatula 30x200 mm

518063 Standard needle 2.5 g (up to 350 u.) 941816 Needle w ith shoulder 2.5 g941737 Holder 47.5 g941738 Standard cone 102.5 g

9418172 Sample container brass nickel plated

9418762 Bulb 230V /15W11500 ASTM thermometer 13C

21712 Sample container one use 55x35 mm (pack of 300)

230 V16 A50 Hz55 Kgw 640 mmd 580 mmh 680 mm

9417343 Magnify ing glass for ref . 941734

9417341 Light bulb for ref . 9417349417342 Flexible light for ref . 941734


9417421 - GREASE WORKER FOR ¼ CONE9417431 - GREASE WORKER FOR ½ CONE


4


SCOPEThis test method covers the determination of the softening point of bitumenin the range from 30 to 157°C using the ring and ball apparatus immersedin distilled water (30 to 80°C), glycerin (80 to 157°C), or ethylene glycol (30to 110°C).


REF. 20761Ring and ball apparatus two-test unit including frame for 2 rings with centeringguide, a pack of 10 shouldered rings, a pack of 10 balls, one beaker, one15C thermometer and one 16C thermometer.

ACCESSORY

SPARE PARTS

REF. 40100The NBA 440 model, fully automatic tester, is equipped with ticket printer,Pt 100 probe and all equipment to perform test with shouldered rings.

SPARE PARTS

ASTM D 36 Softening Point of Bitumen (Ring and Ball)


20761 - MANUAL TESTER


40100 - AUTOMATIC RING & BALL NBA 440

11502 ASTM thermometer 15C11503 ASTM thermometer 16C11565 ASTM thermometer 113C

17487 Calibrated beaker20764 Straight rings (pack of 10)20765 Shouldered rings (pack of 10)25666 Conical rings (pack of 10)40103 Detection lamp

20766 Balls (pack of 10)


20766 Balls (pack of 10)

40138 Ring and ball craddle

40390 Printer paper Seyko DPU 414 (roll)

40139 Pt 100 probe for NBA 44040154 Heating element (1000 W)

20764 Straight rings (pack of 10)20765 Shouldered rings (pack of 10)25666 Conical rings (pack of 10)

26302 Electric stirrer w ith heater type E

5


SCOPEThis test method covers the determination of the flash point, by tag manualand automated closed testers, of liquids with a viscosity below 9.5 cst at25°C and a flash point below 93°C.

REF. 40600The NTA 440 model, fully automatic tester, is equipped with ticket printer,cup and cover, cup support, Pt 100 probe, detection cable and gas tubing.

OPTIONAL ACCESSORIES

SPARE PARTS

ASTM D 56 Flash Point by Tag Closed Tester


40600 - TAG CLOSED TESTER NTA 440

SCOPEThis test method covers the determination of the specific gravity and den-sity of semi-solid bitumous materials, asphalts cements, and soft tar pitchesby use of a pycnometer.

OTHER STANDARDNFT 66007

REF. 24615Thermostatic bath (capacity 16 l) made of stainless steel with cooling coiland lid.

NECESSARY ACCESSORY


ASTM D 70 Density of Semi-Solid Bitumous Materials(Pycnometer Method)

23203 Cryostat TLC 30 - 5 liters (-30/+60°C ±.1)23204 Cryostat TLC 40 - 11 liters (-45/+20°C ±.05)

40318 Pt 100 probe 40611 Heating element 250W (each)40610 TAG cup40612 Detection cable

11532 ASTM thermometer 63C

20847 Pycnometer A ( 24/30 ml)23229 Pycnometer C ( 24/30 ml)23230 Pycnometer D ( 24/30 ml)24624 Pycnometer B ( 24/30 ml)

230 V2.2 A50 Hz18 Kgw 260 mmd 535 mmh 500 mmon request115V 60Hz


PYCNOMETER

40390 Printer paper Seyko DPU 414 (roll)40613 Electric ignitor (NCL440/NTA440)

6


See other applications under ASTM D 850 - D 1078

SCOPEThis test method covers the distillation of natural gasolines, motor gasiolines,aviation gasolines, aviation turbine fuels, special boiling point spirits, naphtas,white spirit, kerosines, gas oils, distillate fuel oils, and similar petroleumproducts, utilizing either manual or automated equipment.

OTHER STANDARDSIP 123 - NFM 07002 - ISO 3405 - DIN 51751

REF. 941227“Front View” distillation apparatus, single unit (receiver on left), with electricheater and temperature control by variotronic, complete with 125 ml flask,100 ml receiver, 2 thermometers, Ceran board 50 and 100 mm.

REF. 941228“Front View” distillation apparatus, single unit (receiver on right), with elec-tric heater and temperature control by variotronic, complete with 125 mlflask, 100 ml receiver, 2 thermometers, Ceran board 50 and 100 mm.

REF. 942228Distillation apparatus model NDI 210 (receiver on right), with electric heatercontrolled by “Pulsotronic” and condenser bath regulated by electronic headproviding external cryostate connections, complete with 125 ml flask,100 ml receiver, silicone stopper, 2 thermometers, Ceran board 50and 100 mm.

SPARE PARTS

OPTIONAL ACCESSORY

DISTILLATION FLASK 125 ml REF. 24019

1 to 9 pieces 10 to 49 pieces 50 and more

ASTM D 86 Distillation of Petroleum Products


941228 - FRONT VIEW DISTILLATION (right)

941251 Glass cooling bath for 941227 and 228 (2l)

19425 100 ml graduated receiver (D86)20348 Ceran board hole 50 mm24019 125 ml distillation f lask (D86)

40101 Heating element (1000W)11494 ASTM thermometer 7C11495 ASTM thermometer 8C

40049 Silicone stopper for condenser (pack of 50)40050 Silicone stopper thermometer (pack of 50)


40078 Karanape board (38 mm)40079 Karanape board (32 mm)

19422 200 ml dis tillation f las k (D1078)


942228 - DISTILLATION APPARATUS semi-automatic


7


REF.40000Model NDI 440, automatic stand alone unit operable through PC keyboardand standard 17” colour screen or alternatively connectable to external ex-isting Pentium PC with Windows software. Basic unit with distillation flasksand CERAN boards as per mentioned methods, 100 ml receiver, 5 ml resi-due receiver, sensor adjuster, Pt 100 sensor, automatic dry point kit, printerand more.

MAIN CONSUMABLES

REFERENCE FLUID (see page 76)

SPARE PARTS

DISTILLATION FLASK 125 ml REF. 24019

1 to 9 pieces 10 to 49 pieces 50 and more


40000 - AUTOMATIC DISTILLATION NDI 440

ASTM D 86 continued

19096 Seepage f ingers (pack of 10)19420 100 ml distillation f lask (D86 - gr 0)19422 200 ml distillation f lask (D1078)

24019 125 ml distillation f lask (D86)26111 100 ml graduated receiver glass foot (D86)40052 125 ml black bottom flask (D86)40065 Tef lon centering stopper for Pt 100 probe40067 Tef lon centering stopper for dry point40073 Dry point thermocouple40078 Karanape board (38 mm)40079 Karanape board (32 mm)

12609 5 ml graduated cylinder for residue (D86)20348 Ceran board hole 50 mm21944 Ceran board hole 100 mm (NDI 440)24019 125 ml distillation f lask (D86)27581 Ceran board hole 25 mm (benzene-toluene D850)

40049 Silicone stopper for condenser (pack of 50)40076 Pt 100 f lask temperature measuring probe

40043 200 ml black bottom flask (D1078)


40078 Karanape board (38 mm)40079 Karanape board (32 mm)

40390 Printer paper Seyko DPU 414 (roll)40101 Heating element (1000W)

40097 Maintenance kit for ND I440

8


ASTM D 91 Precipitation Number of Lubricating Oil

29038 - OIL TEST CENTRIFUGE

See other applications under ASTM D 96 - D 893 - D 1796 - D 2273 - D 2709 - D 2711 - D 4007

SCOPEThis test method covers the determination of the precipitation number ofsteam cylinder stocks and black oils, and can be used for other lubricatingoils.

REF. 29038Model ROTANTA 460 without cooling/heating control is suitable for ASTMD 91, D 893, D 2273, D 2709 et D 2711. Equipped with brushless motorand controlled by microprocessor.DELIVERED WITHOUT ACCESSORY.

REF. 29039Model ROTANTA 460 RHK with cooling/heating control is suitable for ASTMD 96 and D4007. Equipped with brushless motor and controlled by micro-processor.DELIVERED WITHOUT ACCESSORY.

NECESSARY ACCESSORIES

See other application under ASTM D 244

SCOPEThis test method covers the empirical procedures for determining the SayboltUniversal or Saybolt Furol Viscosities of petroleum products at specifiedtemperatures between 21 and 99°C.

REF. 272381 place Saybolt viscometer, equipped with electric heater, automatic con-trol of temperature, stirring motor for water circulation, possibility to cooldown the bath by means of an external cooling system. Supplied withoutaccessories.


ASTM D 88 Saybolt Viscosity

230 V7 A50/60 Hz90 Kgw 554 mmd 707 mmh 453 mm

29040 Rotor 4 places for conical or pear tube29041 Groove suspension29042 Reducing adapter19319 8" cone-shaped tube (100 ml)



27238 - SAYBOLT VISCOMETER


27243 Universal Saybolt tube <1000 sec27244 Furol Saybolt tube >1000 sec11438 Saybolt f lask 60 ml

9


SCOPEThis test method describes the determination of the flash point of petro-leum products by a manual or automated cleveland open cup apparatus.

OTHER STANDARDSIP 36 - NF EN ISO 2592

MANUAL INSTRUMENTREF. 942611This manual model NCL 120 includes cup and thermometer.

SPARE PARTS

SEMI-AUTOMATIC INSTRUMENTREF. 942610The semi-automatic tester NCL 220 is equipped with electronic regulator,and cup. The temperature slope is automatically controlled by Pt100 probe.

SPARE PARTS

AUTOMATIC INSTRUMENTREF. 40400The fully automatic tester NCL 440 is equipped with ticket printer, Pt 100,cup, detection cable, gas tubing and RS232C output. It is provided withgas and electrical ignition system.

OPTIONAL ACCESSORY


SPARE PARTS

ASTM D 92 Flash and Fire Points by Cleveland Open Cup

942611 - MANUAL CLEVELAND NCL 120



40400 - AUTOMATIC CLEVELAND NCL 440


40440 - AUTO-CLEVELAND WITH SAMPLER

941613 Cleveland cup w ith handle



230 V0.3 A50 Hz7 Kgw 350 mmd 250 mmh 430 mm

40440 6 cups automatic sampler

40417 Standard Cleveland cup

40441 Pt 100 probe

40437 Insulated plate - f ixed

40443 Ionization ring f lash point40444 Ionization ring f ire point

40439 Insulated plate - mobile

40390 Printer paper Seyko DPU 414 (roll)40613 Electric ignitor (NCL440/NTA440)40154 Heating element (1000 W)

941615 Stoptherm insulating board941609 Gas tubing diam. 2/4 mm (1 m)

941609 Gas tubing diam. 2/4 mm (1 m)941615 Stoptherm insulating board


942610 - SEMI-AUTO CLEVELAND NCL 220


9417908 Pt 100 probe (70x3 mm)941613 Cleveland cup w ith handle

40154 Heating element (1000 W)

picture not mandatory40154 Heating element (1000W)

9417444 Gloves (pair)


10


SCOPEThis test method covers the determination of the flash point of petroleumproducts in the temperature range from 40 to 360°C by manual or auto-mated Pensky-Martens closed cup apparatus.

OTHER STANDARDSIP 34 - NF EN ISO 2719 - DIN 51758

MANUAL INSTRUMENTSREF. 942614 / 615Models NPM 120, manual instruments, are delivered complete with cupand cover, thermometers and stirrer. Those models are cooled by air andequipped with a safety thermostate. Model 942614 follows method A andmodel 942615 method B.

REF. 942616Model NPM 121, manual instrument, is delivered complete with cup andcover, thermometers and stirrer. This model is cooled by air and equippedwith a safety thermostate.This model follows method A and B.

SPARE PARTS

SEMI-AUTOMATIC INSTRUMENTSREF. 942617 / 618Models NPM 220, semi-automatic instruments, are delivered complete withcup and cover, Pt100 probe and stirrer. Those models are cooled by air andequipped with a safety thermostate. The temperature slope is automati-cally controlled. Model 942617 follows method A and model 942618method B.

REF. 942619The model NPM 221, semi-automatic instrument, is delivered completewith cup and cover, Pt100 probe and stirrer. Those models are cooled byair and equipped with a safety thermostate.The temperature slope is auto-matically controlled. This model follows method A and B.

SPARE PARTS

ASTM D 93 Flash Point by Pensky-Martens Closed Cup


942614/615 - PENSKY-MARTENS NPM 120Manual apparatus



942616 - PENSKY-MARTENS NPM 121Manual apparatus


941621 Heating cartridge 230V (400W)

9411930 Cup for NPM 120, 121, 220, 2219411931 Cover for NPM 120, 121, 220, 221

9411930 Cup for NPM 120, 121, 220, 2219411931 Cover for NPM 120, 121, 220, 221


9417444 Gloves (pair)9417908 Pt 100 probe (70x3 mm)


942617/618 - PENSKY-MARTENS NPM 220Semi-automatic apparatus



942619 - PENSKY-MARTENS NPM 221Semi-automatic apparatus


941621 Heating cartridge 230V (400W)941609 Tube gaz diam. 2/4 mm (1 m)

11496 ASTM thermometer 9C11497 ASTM thermometer 10C

941609 Tube gaz diam. 2/4 mm (1 m)

11


SCOPEThis test method covers the determination of water in petroleum products,tars, and other bitumous materials by the distillation method.

OTHER STANDARDSIP 74 - NFT 60113 - ISO 3733

REF. 21454Complete assembly with heating mantle, glass flask 500 ml and Liebigcondenser 400 mm and all assembly accessories.

SPARE PARTS

ASTM D 95 Water in Petroleum Products and BitumousMaterials by Distillation

12852 Round bottom f lask CN24/29 (500 ml)13142 Liebig condenser CN24/29 (400 mm) 14571 Heating mantle 500 ml (230V /225W)16252 Clamp16324 Stand w ith rod 12 x 800 mm16329 Universal bosshead for assembly19357 Dean Stark trap (10ml in 0.1)21003 Pulse regulator (2200 W)21455 5 ml : 1/10 Dean Stark w ith round bottom21456 25 ml : 1/5 Dean Stark w ith conical bottom


40300 - AUTO PENSKY-MARTENS NPM 440

40349 Stirring connection cable40351 Detection cable

40346 Cup for NPM 44040347 Cover w ithout probe for NPM 440

40353 Pt 100 for NPM 440


14110 Tube for propane gas 6x12 mm (10 m)

40390 Printer paper Seyko DPU 414 (roll)40380 Electric ignitor (NPM 440)

AUTOMATIC INSTRUMENTREF. 40300The NPM 440 model, fully automatic tester, is delivered complete with cupandcover, Pt 100 probe, flexible stirrer, gas or electrical ignition system, PC serialport and ticket printer. Software allows choice of 6 methods, automatic baro-metric correction, full safeties, 2 stirring speeds, ...

OPTIONAL ACCESSORY


SPARE PARTS

21454 - WATER BY DISTILLATION APPARATUS


12



SCOPEThis test method is intended for use on any petroleum product.


REF. 941584Single temperature bath with 5 wells, stirrer and 6 thermometers 5C.Cooled by dry ice.

ACCESSORY

REF. 941592Cloud and pour test cabinet, mechanically refrigerated by CFC free gases,4 compartments (0, -17, -34, -51 °C), each with 4 sleeves including testtubes, felts, 15 thermometers 5C and 5 thermometers 6C.

REF. 941595Cloud and pour test cabinet, mechanically refrigerated by CFC free gases,1 compartment (-69 °C), with 4 sleeves including test tubes, felts, ther-mometers 5C and thermometer 6C.


SPARE PARTS

AUTOMATIC MODEL ON REQUEST

ASTM D 97 Pour Point of Petroleum Products


941592 - CLOUD & POUR CABINET (0 to -51°C)

941597 Dry ice machine

9415901 Felt disc (pack of 10)9415902 Felt ring (pack of 10)11492 ASTM thermometer 5C11493 ASTM thermometer 6C11530 ASTM thermometer 61C

230 V16 A50 Hz190 Kgw 1000mmd 750 mmh 1420 mm

19439 Test tube

See instrument under ASTM D 91

SCOPEThis test method covers the centrifuge method for determining sedimentand water in crude oil during field custody transfers.

ASTM D 96 Water and Sediment in Crude Oil byCentrifuge Method

13



SCOPEThis test method covers the determination of sulfur in petroleum products,including lubricating oils containing additives, additive concentrates, and lu-bricating greases that cannot be burned completely in a wick lamp.

OTHER STANDARDSIP 61 - NFT 60109 - DIN 51577

ASTM D 129 Sulfur in Petroleum Products(general Bomb Method)

SCOPEThe ductility of a bituminous material is measured by the distance to whichit will elongate before breaking when two ends of a briquet specimen of thematerial are pulled apart at a specified speed and temperature.

OTHER STANDARDSNFT 66006 - DIN 52013

REF. 9418641Ductility machine with electronic regulation and digital display measurement,for three simultaneous tests at variable speeds of 1 to 99 mm/min by stepof .1 mm, maximum pull length : 100 cm

REF. 9418642Ductility machine with electronic regulation and digital display measurement,for three simultaneous tests at variable speeds of 1 to 99 mm/min by stepof .1 mm, maximum pull length : 150 cm

ACCESSORIES

SPARE PARTS

ASTM D 113 Ductility of Bituminous Materials


9418641 - DUCTILITY MACHINE (1 meter)

941868 Mould w ithout brass plate941869 Brass plate



941866 Opal glass for ductility meter 100 cm 941865 Opal glass for ductility meter 150 cm

23203 Cry os tat TLC 30 - 5 liters (-30/+60°C ±.1)941867 Transparent cover for ductility meter

14


SCOPEThis test method covers the detection of the corrosiveness to copper ofaviation gasoline, aviation turbine fuel, automotive gasoline, natural gaso-line or other hydrocarbons having a Reid vapor pressure no greater than 18psi.


REF. 941220Constant temperature test bath with plain cover and drain cock, controlledby electronic thermostat, Pt 100 sensor and led heating control(max 100°C).

NECESSARY ACCESSORIES FOR ASTM D 130

SPARE PARTS

NECESSARY ACCESSORIES FOR IP 227

SPARE PARTS

ASTM D 130 Detection of Copper Corrosion fromPetroleum Products


941220 - TEST BATH FOR D130


941220 - TEST BATH FOR IP 227

12780 Test tube 25x150mm 24541 Single strip polishing vise15114 Copper strip corrosion test standard15115 Copper strip (pack of 10)19008 Flat glass test tube941492 Test cylinder12067 Silicon carbide paper 240 grits9413109 Support to hold 12 stainless steel vessel9413125 Support to hold 40 test tubes11499 ASTM thermometer 12C22505 Silicon carbide pow der 150 mesh (1 kg)

19008 Flat glass test tube941492 Test cylinder

9414920 "O" ring seals (pack of 10)

22505 Silicon carbide pow der 150 mesh (1 kg)

12780 Test tube 25x150mm

941224 Cover including 3 test tubes (amber) 9414851 Silver strip assaying at 99.9%

9414931 Silver strip corrosion standard


9414851 Silver strip assaying at 99.9%




24541 Single strip polishing vise

12007 Kit condenser complete (amber glass)

22505 Silicon carbide pow der 150 mesh (1 kg)

12067 Silicon carbide paper 240 grits

9417900 Pt 100 probe (30x6 mm)

9417900 Pt 100 probe (30x6 mm)


9412209 Heating element (1500 W)12008 Craddle (amber glass)12376 Test tube (amber glass)12377 Cold-f inger condenser (amber glass)


15114 - CORROSION TEST STANDARD

15


SCOPEThis test method covers the determination of the color of refined oils suchas undyed motor and aviation gasoline, jet propulsion fuels, naphtas andkerozine, and, in addition, petroleum waxes and pharmaceutical white oils.

OTHER STANDARDSNFM 07003 - DIN 51411

REF. 941520Complete improved model with daylight source built-in the base and a 3-position turret assembly (½, 1 and 2) with certified Saybolt filters reducingthe time required to make a determination and eliminating the handling ofthe standard filters and the possibility of loss and damage.

REF. 941521Same model as above but with specific heating tube for petroleum waxes.Maximum temperature of use 100 °C.

SPARE PARTS

AUTOMATIC APPARATUSREF. 29006 ON REQUESTThe Lovibond PFX 880/P is an easy to use, automatic instrument, whicheliminates time-consuming procedures of visual methods. It is a spectro-photometer for objective colour analysis of petroleum fuels, oils, waxesand petrochemicals according to the Saybolt and ASTM Colour scales

ASTM D 156 Saybolt Color of Petroleum Products


941520 - SAYBOLT CHROMOMETER

941524 Prismatic eyepiece

9415221 O ring for graduated tube (pack of 10)

941525 Matched pair of tubes

9415203 Artif ic ial daylight f ilter w ith certif icate9415206 Spare bulb

9415240 Filter w heel w ith certif icate


9415222 Seal for glass disk (pack of 10)

941526 Matched pair of tubes for w axes


941521 - SAYBOLT CHROMOMETER FORPETROLEUM WAXES


16


ASTM D 217 Cone Penetration of Lubricating Grease

See instruments under ASTM D 5

SCOPEThis test method covers four procedures for measuring the consistency oflubricating greases by the penetration of a cone of specified dimension,mass, and finish. The penetration is measured in 1/10 of a millimeter.


ASTM D 240 Heat of Combustion of Liquid HydrocarbonFuels by Bomb Calorimeter


SCOPEThis test method covers the determination of the heat of combustion ofliquid hydrocarbon fuels ranging in volatillty from that of light distillates tothat of residual fuels.

QUOTATION ON REQUEST


SCOPEThis test method covers the determination of the amount of carbon residueleft after evaporation and pyrolisis of an oil. It is intended to provide someindication of relative coke-forming propensities. The method is generallyapplicable to relatively non volatile petroleum products which partially de-compose on distillation at atmospheric pressure.

OTHER STANDARDSNFT 60116 - IP 13 - ISO 6615 - DIN 51551

REF. 941653Single unit model to be manually used including: porcelain crucible, skidmorecrucible with cover, steel outer crucible with lid, support triangle, holder,chimney stand and the gas burner.

SPARE PARTS

ASTM D 189 Conradson Carbon Residue of PetroleumProducts


941653 - CARBON RESIDUE APPARATUS

27083 Meker gas burner (butane/propane)

941661 Skidmore crucible w ith brass lid941664 Steel outer crucible941665 Metallic hollow ring941666 Chimney w ith guide15150 Porcelain Conradson crucible (pack of 12)

10702 Glass balls diam. 2mm (1 kg)

8 Kgw 250 mmd 250 mmh 500 mm

17


See other applications under ASTM D 941 - D 1217 - D 1298 - D1480

SCOPEThis test method covers the determination by means of a glass hydrometerof the API gravity of crude petroleum and petroleum products normally han-dled as liquids and having a Reid vapor pressure no greater than 26 psi.

OTHER STANDARDISO 3675

REF. 148546-unit ramp in stainless steel

ACCESSORIES (for all standards)

ACCESSORIES (ASTM D287)

ACCESSORY (ASTM D941)

ACCESSORY (ASTM D1217)

ACCESSORIES (ASTM D1298)

OPTIONAL

ASTM D 287 API Gravity of Crude Petroleum andPetroleum Products (Hydrometer Method)

10013 Spare glassw are w ith cock10741 Density cylinder 500 ml15287 AFNOR thermometer, -15 to +45°C15288 AFNOR thermometer, +35 to +85°C

20800 Hydrometer API 1H / -1 to 1120801 Hydrometer API 2H / 9 to 2120802 Hydrometer API 3H / 19 to 3120803 Hydrometer API 4H / 29 to 4120804 Hydrometer API 5H / 39 to 5120805 Hydrometer API 6H / 49 to 6120806 Hydrometer API 7H / 59 to 7120807 Hydrometer API 8H / 69 to 8120808 Hydrometer API 9H / 79 to 9120809 Hydrometer API 10H / 89 to 101

19386 Lipkin density bottle

19393 25 ml Bingham density bottle

20810 Hydrometer (L50) / 0,600-0,65020811 Hydrometer (L50) / 0,650-0,70020812 Hydrometer (L50) / 0,700-0,75020813 Hydrometer (L50) / 0,750-0,80020814 Hydrometer (L50) / 0,800-0,85020815 Hydrometer (L50) / 0,850-0,90020816 Hydrometer (L50) / 0,900-0,95020817 Hydrometer (L50) / 0,950-1,00020818 Hydrometer (L50) / 1,000-1,05020819 Hydrometer (L50) / 1,050-1,10020820 Thermohydrometer API 51H / -1 to 1120821 Thermohydrometer API 52H / 9 to 2120822 Thermohydrometer API 53H / 19 to 3120823 Thermohydrometer API 54H / 29 to 4120824 Thermohydrometer API 55H / 39 to 5120825 Thermohydrometer API 56H / 49 to 6120826 Thermohydrometer API 57H / 59 to 7120827 Thermohydrometer API 58H / 69to 8120828 Thermohydrometer API 59H / 79 to 9120829 Thermohydrometer API 60H / 89 to 101

941123 Water bath for hydrometer


14854 - 6 UNIT RAMP


20800 - API HYDROMETER 1H


941123 - WATER BATH

230 V4 A50 Hz7.5 Kgw 350 mmd 260 mmh 300 mm

18


SCOPEThis test method covers procedures for the determination of vapor pres-sure of gasoline, volatile crude oil, and other volatile petroleum products.

OTHER STANDARDSIP 69 - NFM 07007 - ISO 3007 - EN 12

REF. 941432Electronic constant thermostatic bath, 3 vessels capacity, with thermom-eter and digital display. Equipped with adjustable stirring device, low watercut-off, cooling coil for external cryostat and drain cock.

REID VESSELS WITH SCREW COUPLING

REID VESSELS WITH QUICK COUPLING

REID VAPOUR PRESSURE GAGES (psi and KPa)


SPARE PARTS

ASTM D 323 Vapor Pressure of Petroleum Products(Reid Method)


941432 - THERMOSTATIC BATH (3 place)


941411 - VESSEL WITH QUICK COUPLING


941401 - VESSEL WITH SCREW COUPLING

941401 RVP screw coupling test vessel (below 26 lb)941405 RVP screw coupling test vessel (above 26 lb)

941411 RVP quick coupling test vessel (below 26 lb)941415 RVP quick coupling test vessel (above 26 lb)

941420 Metallic manometer 0 to 5 psi/34 kPa941421 Metallic manometer 0 to 15 psi/100 kPa941422 Metallic manometer 0 to 45 psi/300 kPa941423 Metallic manometer 0 to 60 psi/400 kPa941424 Metallic manometer 0 to 100 psi/650 kPa9414211 Metallic manometer 0 to 30 psi/200 kPa

941410 Safety burst disk capsule (add on vessel price)25755 Mercury manometer9414283 Connection for mercury manometer

941402 A ir chamber (screw )941403 Gasoline chamber w ith one opening (screw )941407 Gasoline chamber w ith tw o valves (screw )

941427 Tef lon gaskets for test vessel (2 packs of 12)

9414101 Spare disc for safety capsule941435 Heating element (2000 W)

941413 Gasoline chamber w ith one opening (q. coupling)941417 Gasoline chamber w ith tw o valves (q. coupling)


9417905 Pt 100 probe (250x5 mm)

19


SCOPEThis test method covers the determination of the existent gum content ofaviation fuels, and the gum content of motor gasolines or other volatile dis-tillates in their finished form, and at the time of test.


REF. 941302This model, air jet only with 5 wells, includes electronic temperature controland flowmeter, thermometer 3C, beakers, conical outlets.

REF. 941303This model, air and steam jet with 5 wells, includes electronic temperaturecontrol and flowmeter, steam superheater, thermometer 3C, beakers, conicaloutlets.

ACCESSORIES

SPARE PARTS

for aluminium block for calibration kit for superheater

ASTM D 381 Existent Gum in Fuels by Jet Evaporation


941303 - AIR AND STEAM JET GUM BATH


941308 - STEAM GENERATOR


941302 - AIR JET GUM BATH


9413080 - AIR COMPRESSOR


941301 and 941304 - CALIBRATION KIT

941308 Steam generator (400V - 3 ph)

941301 A ir calibration kit for 941302/941303941304 Vapour calibration kit for 941303

9413080 A ir compressor 2 stages 300 l (400V - 3 ph)

12875 Filter funnel 125 ml

941306 Conical air outlet

9413031 Superheater for 941303 apparatus




400 V - 3ph20 A50 Hz75 Kgw 750 mmd 530 mmh 920 mm

400 V - 3 ph7 A50 Hz125 Kgw 760 mmd 600 mmh 1670 mm


941307 Overpressure pump for steam generator

9417900 Pt 100 probe (30x6 mm)9417904 Pt 100 probe (160x5 mm)

9417834 Pt 100 probe (60x3.15 mm)

9413023 Heating element for metallic bath9417444 Gloves (pair)

16138 Test cell

20


ASTM D 445 Kinematic Viscosity of Transparent andOpaque Liquids

SCOPEThis test method specifies a procedure for the determination of the kin-ematic viscosity of liquid petroleum products, both transparent and opaque,by measuring the time for a volume of liquid to flow under gravity through acalibrated glass capillary viscometer.

OTHER STANDARDSIP 71 - ISO 3104 - DIN 51366

REF. 60100Normalab Analis Fully Automatic Houillon viscometer - Model NVH 450 -- Plug and play equipmen t : no external connexion for use above ambient- 4 tubes in the same bath- Measuring range from 0.2 to 5000 cSt- Temperature range from 40 to 120°C (optional chiller can be connected)- Automatic tube cleaning

Our New automatic Houillon viscometer NVH 450 combines the advan-tages of a quick and economical standard method for viscosity measure-ment with the latest improvements in technology to reach comfort of useand accuracy. 4 tests can be launched simultaneously and apart from sam-ple introduction, all the operations are driven by the internal CPU.

NVH 450 is delivered with cleaning system and pump included.Silicone oil, tubes and pipettes to be ordered separately

ACCESSORIES

VISCOSITY STANDARDS (see page 25)

SPARE PARTS


HOUILLON VISCOMETER TUBES

60100 - HOUILLON VISCOMETER NVH 450


TUBE NVH 450



HOUILLON VISCOMETER NVH 450 - screen shot


60151 Houillon tube size 50 w ithout certif icate60152 Houillon tube size 75 w ithout certif icate60153 Houillon tube size 100 w ithout certif icate60154 Houillon tube size 150 w ithout certif icate60155 Houillon tube size 200 w ithout certif icate60156 Houillon tube size 300 w ithout certif icate60157 Houillon tube size 350 w ithout certif icate60158 Houillon tube size 400 w ithout certif icate60159 Houillon tube size 450 w ithout certif icate60160 Houillon tube 45 cSt w ithout certif icate

24022 Glasstube for sampling and sample introduction24958 Sampling Micro pipet24960 Cone for pipet (pack of 1000)27775 Demineralized w ater below 50°C (can of 20 l)60101 Silicon oil (20 l)

60102 Vacuum pump PM 999960103 Burker SV 2 w ays60104 Burker SV 3 w ays60105 Gasket for cleaning clamp60107 Waste bottle w ith cover and gasket60108 Solvent bottle w ith cover and gasket60113 Safety w aste bottle w ith cover and gasket60114 Complete cleaning clamp


40386 Printer DPU 414 and cable

60135 Modified thermometer 120C for NVH 45060136 Modified thermometer 121C for NVH 450

21


REF. 17915Constant temperature viscosity bath “ROUTINE” (max. 100°C) with glassjar of 20 liters, thermometer for temperature reading and 5 places for com-mon viscometers (support not included).

REF. 23829Constant temperature viscosity bath “ROUTINE” (max. 200°C) with glassjar of 20 liters, digital temperature display and 5 places for commonviscometers (support not included).

REF. 941131Constant temperature viscosity bath “PRECISION” (max. 120°C) with glassjar of 30 liters, electronic digital temperature control and 8 places turntableforcommon viscometers (support not included).

SPARE PARTS




REF.18450VISCOMETER WASHER supplied with 6 nozzle stoppers. This apparatusis allowed for external and internal washing of all current types of viscometertubes. The viscometer tubes are suspended in BIOSANE T215 solventvapors at 80°C.- Very fast cleaning for 6 viscometer tubes in 5 to 15 min- Negligible solvent consumption

SPARE PARTS

RECOMMENDED SOLVENT

23829 - VISCOSITY BATH (5 places)


941131 - VISCOSITY BATH (8 places)

10568 Suspension nylon for Cannon10569 Suspension nylon for Ubbelohde

13539 Support for 6 v iscometer tubes16419 Silicone oil up to 150°C (5 l)16427 Mineral oil max 100°C (5 l)21375 Electronic stopw atch

941132 Heating element for ref . 941131 (2000 W)



9417904 Pt 100 probe (160x5 mm)9411302 Borosilicate glass jar(300 x 450 mm)

10567 Suspension stainless steel for Ubbelohde



18450 - AUTOMATIC VISCOMETER WASHER ALV 110


21694 Heating controller 18455 Glass c leaning bath18454 Injector stopper18453 Heating element

25699 Biosane T215 solvent (5 l)


22CN06-2uk (all previous editions obsolete)

1. Ubbelohde viscometer for transparent liquids

2. Cannon-fenske routine viscometer for transparent liquids

3. Cannon-fenske reverse flow viscometer for opaque liquids

4. BS / IP U RF viscometer for opaque liquids

ALL ABOVE VISCOMETERS CAN BE SUPPLIEDWITHOUT CERTIFICATE ON SPECIAL REQUEST

ASTM D 445 continued

VISCOMETER TUBES (all with calibration certificate)

2. Cannon-fenske

1. Ubbelohde

3. Cannon-fenske

4. BS / IP U RF

14030 0,3 to 1 cSt - s ize 014031 0,6 to 3 cSt - s ize 0C14032 1 to 5 cSt - s ize 0B14034 2 to 10 cSt - s ize 114035 6 to 30 cSt - s ize 1C14036 10 to 50 cSt - s ize 1B14037 20 to 100 cSt - s ize 214038 60 to 300 cSt - s ize 2C14039 100 to 500 cSt - s ize 2B14041 200 to 1000 cSt - s ize 314042 600 to 3000 cSt - s ize 3C14043 1000 to 5000 cSt - size 3B14044 2000 to 10000 cSt - s ize 414045 6000 to 30000 cSt - s ize 4C13993 10000 to 50000 cSt - s ize 4B13994 20000 to100000 cSt - s ize 5

14002 0,4 to 2 cSt - s ize 2514003 0,8 to 4 cSt - s ize 5014004 1,6 to 8 cSt - s ize 7514005 3 to 15 cSt - s ize 10014006 7 to 35 cSt - s ize 15014007 20 to 100 cSt - s ize 20014008 50 to 200 cSt - s ize 30014009 100 to 500 cSt - s ize 35014010 240 to 1200 cSt - s ize 40014011 500 to 2500 cSt - s ize 45014012 1600 to 8000 cSt - size 50014013 4000 to 20000cSt - s ize 60014014 10000 à 40000 cSt - s ize 65014015 20000 à 80000 cSt - s ize 700

14016 0,4 to 2 cSt - s ize 2514017 0,8 to 4 cSt - s ize 5014018 1,6 to 8 cSt - s ize 7514019 3 to 15 cSt - s ize 10014020 7 to 35 cSt - s ize 15014021 20 to 100 cSt - s ize 20014022 50 to 200 cSt - s ize 30014023 100 to 500 cSt - s ize 35014024 240 to 1200 cSt - s ize 40014025 500 to 2500 cSt - s ize 45014026 1600 to 8000 cSt - size 50014027 4000 to 20000cSt - s ize 60014028 10000 à 40000 cSt - s ize 65014029 20000 à 80000 cSt - s ize 700

18670 0.6 to 3 cSt - s ize 118671 2 to 10 cSt - s ize 218672 6 to 30 cSt - s ize 318673 20 to 100 cSt - s ize 418674 60 to 300 cSt - s ize 518675 200 to 1000 cSt - s ize 618676 600 to 3000 cSt - s ize 718677 2000 to 10000 cSt - s ize 818678 6000 to 30000 cSt - s ize 918679 20000 to 100000 cSt - s ize 1018680 60000 to 300000 cSt - s ize 11

23


5. Houillon viscometer for transparent liquids

6. BS / IP SL viscometer for transparent liquids

7. S.I.L. viscometer for transparent liquids

8. BAUME VIGNERON viscometer for transparent liquids

9. CANNON MANNING VACUUM viscometer for bitumen


VISCOMETER TUBES (all with calibration certificate)

8. BAUME VIGNERON

9. CANNON MANNING VACUUM

7. S.I.L.

6. BS / IP SL

5. Houillon

13932 3.2 cSt13933 6.4 cSt13934 12 cSt13935 28 cSt13936 80 cSt13937 200 cSt13938 400 cSt13939 960 cSt13940 2000 cSt

19283 10 cSt19284 30 cSt19285 100 cSt19286 300 cSt19287 1000 cSt19288 3000 cSt19289 10000 cSt19290 30000 cSt19291 100000 cSt

19631 3 cSt19632 10 cSt19497 30 cSt19498 100 cSt19499 300 cSt19500 1000 cSt19501 3000 cSt19502 10000 cSt

14740 0.63 cSt14741 1 cSt14742 1,6 cSt14743 2.5 cSt14744 4 cSt14745 6.3 cSt14746 10 cSt14747 15 cSt14748 25 cSt14749 40 cSt14750 63 cSt14751 100 cSt14752 160 cSt14753 250 cSt14754 400 cSt14755 630 cSt14756 1000 cSt14757 1600 cSt14758 2500 cSt14759 4000 cSt14760 6300 cSt

18892 0.8 cSt18893 2.4 cSt18894 8 cSt18895 24 cSt18896 80 cSt18897 240 cSt18898 800 cSt18899 2400 cSt18900 8000 cSt18901 24000 cSt18902 80000 cSt

24


10. CANNON UBBELOHDE viscometer for transparent liquidswithout connection to washer

11. CANNON UBBELOHDE viscometer for transparent liquidswith connection to washer


VISCOMETER TUBES FOR AUTOMATIC VISCOMETER

10. CANNON UBBELOHDE

11. CANNON UBBELOHDE

15253 0.003 (approx. constant)15255 0.005 (approx. constant)15256 0.01 (approx. constant)15257 0.03 (approx. constant)15259 0.1 (approx. constant)15260 0.3 (approx. constant)15263 1 (approx. constant)15264 3 (approx. constant)15266 10 (approx. constant)

22882 0.005 (approx. constant)22883 0.003 (approx. constant)22884 0.01 (approx. constant)22885 0.03 (approx. constant)22886 0.1 (approx. constant)22887 0.3 (approx. constant)22888 1 (approx. constant)22889 3 (approx. constant)22890 10 (approx. constant)

25CN06-2uk (all previous editions obsolete)

VISCOSITY STANDARDS (1 pint)

AMT

26


SCOPEThis test method covers the determination of sediment in crude oils andfuels oils by extraction with toluene.


REF. 941281Extraction apparatus consisting of erlenmeyer extraction flask, 1000ml ca-pacity, block-tin coil condenser, water cup and extraction thimble suspendedby means of a corrosion resistant wire.

ACCESSORY

SPARE PARTS

ASTM D 473 Sediment in Crude Oils and Fuel Oils by theExtraction Method


941281 - EXTRACTION APPARATUS

10739 Water cup w ith glass hook19012 Extraction f lask (1 litre)

941282 Condenser

10763 Extraction thimble (alundum)


941284 Extraction basket

28754 Hot plate SB 160

27



SCOPEThis test method covers the determination of ash in the range 0.001-0.180mass %, from distillate and residual fuels, gas turbine fuels, crude oils, lu-bricating oils, waxes, and other petroleum products, in which any ash-form-ing materials present are normally considered to be undesirable impuritiesor contaminants.

OTHER STANDARDIP 4

ASTM D 482 Ash from Petroleum Products

SCOPEThis test method covers the determination of the amount of carbon residueleft after evaporation and pyrolysis of an oil, and is intended to providesome indication of relative coke-forming propensity.


REF. 941671This model with 5 wells and control bulb does not include test accessories.


SPARE PARTS

ASTM D 524 Ramsbottom Carbon Residue of PetroleumProducts


941671 - RAMSBOTTOM CARBON TESTER

REF. 23963Muffle furnace model L3/11, 3 liters capacity, maximum temperatureof 1100 °C.

NECESSARY ACCESSORIES (for D482)

NECESSARY ACCESSORIES (for D874)

SPARE PARTS

9419675 10 ml syringe w ith needie941673 Filling device for glass coking bulb19365 Glass coking bulb

9419675 10 ml syringe w ith needie941674 Control bulb w ith thermocouple



9411300 Platinum crucible (100 ml)

10532 Porcelain dish,100 ml,f lat bottom (pack of 6 )10687 Stainless curved crucible tong (pack of 2)10702 Glass balls diam. 2mm (1 kg)10770 Porcelain plate for below dessicator27203 Soda lime glass dessicator diam. 200 mm

10508 Porcelain crucible, 40 ml tall form (pack of 6 )10509 Porcelain crucible, 80 ml tall form (pack of 6 )10510 Porcelain crucible,120 ml tall form (pack of 6 )10515 Porcelain crucible, 80 ml low form (pack of 6 )10532 Porcelain dish,100 ml,f lat bottom (pack of 6 )10687 Stainless curved crucible tong (pack of 2)10702 Glass balls diam. 2mm (1 kg)10770 Porcelain plate for below dessicator27203 Soda lime glass dessicator diam. 200 mm15377 Silica crucible (50 ml tall form)15386 Silica crucible (75 ml low form)15387 Silica crucible (130 ml low form)15671 Platinum crucible (50 ml)

23964 Set of heating elements 23965 Thermoc ouple K (160mm)


23963 - MUFFLE FURNACE


941675 Thermocouple assembly (furnace + safety)

28


See other applications under ASTM D 873

SCOPEThis test method covers the determination of the stability of gasoline infinished form only, under accelerated oxidation conditions.


AUTOMATIC EQUIPMENT MODELS NPI 440 and 442REF. 40925 (for D525 and D873)4-unit automatic Potential gums & Induction period tester, model NPI 442,including metallic bath , direct pressure measurement in the test vessel,over-pressure safety by certified bursting disk and quick coupling, trackingof pressure, pressure drop and break-point on printer or PC, supplied withplotter but without filling accessory, test vessels, sample container, nor PCsoftware.

REF. 40900 (for D525, D873)2-unit automatic Potential gums & Induction period tester, model NPI 440,including liquid bath , direct pressure measurement in the test vessel,over-pressure safety by certified bursting disk and quick coupling, tracking ofpressure, pressure drop and break-point on printer or PC, supplied withplotter but without filling accessory, test vessels, sample container, nor PCsoftware.

REF. 40930The oxygen filling and decompression valve adapter model NPC 210 isdesigned for all type of potential gums and induction period test vessels.The kit provides the operator with a high level of safety.

NECESSARY ACCESSORIES (for D525 and D873)

SPARE PARTS

MANUAL EQUIPMENTREF. 9413724-place water bath with glass condenser and digital temperature control.


SPARE PARTS

ASTM D 525 Oxidation Stability of Gasoline(InductionPeriod Method)


40900 - LIQUID BATH NPI 440 (2 places)


40930 - OXYGEN FILLING CHAMBER NPC 210

409031 Stainless steel vessel w ith burst disk 40909 Filling and decompression (manual)40911 Stand for 2 vessels40933 Gaskets v iton for cylinder (pack of 10)21688 Glass test container w ithout cover513514 Cover for container

941362 Recording pressure gauge (1 for 2 vessels)941365 Charts for recording gauge (pack of 100)21688 Glass test container w ithout cover513514 Cover for container11509 ASTM thermometer 22C


30 Kgw 500 mmd 365 mmh 800 mm

9417902 Pt 100 probe (60x5 mm)


941372 - LIQUID BATH (4 place)


19007 Glass condenser9412209 Heating element (1500 W)9413621 Red Pen for recorder (pack of 5)9413622 Green Pen for recorder (pack of 5)

409031 Stainless steel vessel w ith burst disk 40909 Filling and dec ompres s ion (manual)



40933 Gaskets v iton for cylinder (pack of 10)

40913 Pt 100 probe for liquid bath40916 Heating element for liquid bath (1800 W)

40934 Pt 100 probe for dry bath40935 Heating cartridge for dry bath (4 x 200 W)

40919 Solid state relay for heating element


40925 - METALLIC BATH NPI 442 (4 places)


513513 Glass test container w ith cover

513513 Glass test container w ith cover

29


SCOPEThis test method covers the determination of the aniline point of petroleumproducts and hydrocarbon solvents.


REF. 41100Automatic Aniline Point Tester model NPA 410. Detection of clear to darksample by infrared detection.NO HANDLING OF ANILINE.

ACCESSORIES


SPARE PARTS

REF. 40500Auto aniline point tester model, NAE 440 equipped with 2 independantstations, heating system by metallic bath (+10/+150 °C), printer, automaticdetection of clear, colored and dark samples.


SPARE PARTS

ASTM D 611 Aniline Point and Mixed Aniline Point of Pe-troleum Products and Hydrocarbon solvents


41100 - ANILINE POINT NPA 410


40500 - ANILINE POINT NAE 440

41104 2 ml v ials to crimp (pack of 1000) 41105 Crimp seal (pack of 500)41106 Hand crimper

41109 Thermocouple41117 Set of 2 fuses (2A)




SCOPEThis test method covers the determination of the dropping point of lubricat-ing grease.



ASTM D 566 Dropping Point of Lubricating Grease

41121 Heating cartridge 100W

41121 Heating c artr idge 100W

30


ASTM D 613 Reference and Check Fuel Blending forOctane and Cetane Measurement


SCOPENABLEND series of automatic blending units have been designed to auto-mate the blending procedure for reference and check fuels used for octaneand cetane number measurement.Due to the flexibility of the software the instrument can be used for otherhydrocarbon blending purposes too where the accuracy and the speed ofthe blending procedure are critical.The units are operable locally from the embendded Windows CE basedtouch screen computer or can be remote controlled from any PC having aninternet browser installed over the local area network.The intranet technology software allows complete remote management andservice over the internet or phone line.The blending and calibration data being stored in an internal database, canbe accessed over the local area network.

REF. 52000Model NABLEND 8875 automatic stand alone unit with 2 fluid channels, forblending cetane reference fuels according ASTM D613 composed of twoblending components: nCetane, AMN or HMN, or U and T components.

REF. 52100Model NABLEND 8873 automatic stand alone unit with 3 fluid channels, forblending octane reference and check fuels according ASTM D2699 andASTM D2700 composed of three blending components: iso-octane, nor-mal heptane and toluene.

REF. 52200Model NABLEND 8877 automatic stand alone unit with 5 fluid channels, forblending octane and cetane reference and check fuels according ASTMD613, ASTM D2699 and ASTM D2700 composed of three blending com-ponents: iso-octane, normal heptane and toluene for octane and two blend-ing components: nCetane, AMN or HMN, or U and T components for cetane.

REF. 52300Model NABLEND 8879 automatic stand alone unit with 6 fluid channels, forblending octane and cetane reference and check fuels according ASTMD613, ASTM D2699 and ASTM D2700 composed of four blending compo-nents: iso-octane, normal heptane, 80/20 blend and toluene for octane andtwo blending components: nCetane, AMN or HMN, or U and T componentsfor cetane.

OPTIONAL ACCESSORY

MAIN CONSUMABLE

SPARE PARTS


52000 - AUTOMATIC BLENDING UNIT

90-264 V0.8 A47-440 Hz270 Kgw 610 mmd 820 mmh 1650 mm

52001 Bottle, solvent resistant w ith cock (1l)

52002 Dosing pump

53000 Explosion-proof drum pump

52003 Printer paper (roll)52004 Fuel f ilter52005 Solenoid valve52006 Injec tion head O-r ing

31


SCOPEThis test method covers procedures for the determination of acidic con-stituents in petroleum products and lubricants soluble or nearly soluble inmixture of toluene and propan-2-ol.

OTHER STANDARDSIP 177 - ISO 6619

REF. 941708Neutralisation number apparatus by potentiometric titration, single unit, com-plete with pH test kit.

SPARE PARTS

ASTM D 664 Acid Number of Petroleum Products byPotentiometric Titration


941708 - ACID NUMBER TESTER

941709 PH test kit9417082 Glass electrode (Beck. 39321) 9417083 Calomel electrode (Beck. 39420)19027 Burette (10ml in 0,05 ml)12438 250 ml beaker


ASTM D 665 Rust-Preventing Characteristics of InhibitedMineral Oil in Presence of Water

SCOPEThis test method is used to evaluate the ability of inhibited mineral oils,particularly steam-turbine oils, to aid in preventing the rusting of ferrousparts should water become mixed with the oil. This test method is alsoused for testing other oils, such as hydraulic oils and circulating oils.


REF. 9416306This improved 6 places unit with digital tachometer includes beakers, cov-ers, stainless steel stirrers, test rods with plastic holders and 9C thermom-eters. Polishing machine is not included.

ACCESSORY

SPARE PARTS


9416306 - RUST TESTER

941636 Polishing apparatus w ith electric motor

941631 400 ml beaker941632 Transparent plastic cover941633 Stainless steel stirrer

9416341 Test specimen9416342 Plastic holder



9417904 Pt 100 probe (160x5 mm)



941636 - POLISHING MACHINE


32



SCOPEThis test method covers the determination of chlorine in lubricating oils andgreases containing additives, and in additive concentrates.

ASTM D 808 Chlorine in New and Used PetroleumProducts (Bomb Method)


SCOPEThis test method covers the determination of oil in petroleum waxes havinga congealing point of 30°C or higher as determined in accordance with testmethod D 938, and containing not more than 15% of oil.


REF. 941795Complete apparatus delivered with cooling bath, 3 filter stick, air pressureregulator, evaporation assembly, 4 weighing bottles and thermometer.

SPARE PARTS

ASTM D 721 Oil Content of Petroleum Waxes

941795 - OIL CONTENT TESTER


23240 Weighing bottle (15 ml)517565 Filter stick B24517564 Cooling sample tube

230 V0.3 A50 Hz15 Kgw 600 mmd 300 mmh 450 mm9417902 Pt 100 probe (60x5 mm)

33



SCOPEThis test method covers the distillation of industrial aromatic hydrocarbons

ASTM D 850 Distillation of Industrial AromaticHydrocarbons


SCOPEThis test method covers the determination of the tendency of aviation recip-rocating, turbine, and jet engine fuels to form gum and deposits under ac-celerated aging conditions.

OTHER STANDARDSIP 138 - NFM 07013 - DIN 51799

ASTM D 873 Oxidation Stability of Aviation Fuels(Potential Residue Method)


SCOPEThis test method covers the determination of the sulfated ash from unusedlubricating oils containing additives and from additives concentrates used incompounding.


ASTM D 874 Sulfated Ash from Lubricating Oils andAdditives

SCOPEThis test method covers a referee and a routine procedure for determiningthe dielectric breakdown voltage of insulating liquids.

OTHER STANDARDSIP 295 - NFC 27221

REF. 23797Complete Tester, model OTS60AF/2, for Dielectric Breakdown Voltage,delivered with oil test vessel fitted with spherical electrodes and oil test setpreparation kit comprising stirrers, mushroom and cylindrical electrodes,electrode spacing gauge and protective cover.

REF. 27196Portable tester, model OTS60PB, for routine analysis, delivered with 4 oilvessels, 1 pair of spherical, mushroom and cylindrical electrodes, spacinggauge and protective carrying case.

SPARE PARTS

ASTM D 877 Dielectric Breakdown Voltage of InsulatingFluids

23798 Test container + electrodes for D87723799 Test container + electrodes for NFC 27221 picture not mandatory

27196 - PORTABLE MEGGER

12 V rechargeable

19 Kgw 259 mmd 247 mmh 373 mm

34


SCOPEThis test method covers the determination of the foaming characteristics oflubricating oils at 24°C and 93.5°C.


REF. 941643Twin test units for both 24 and 93.5 °C. Delivered complete with certifieddiffuser stone,glassware, flowmeters and thermometers.

REF. 941640Single test unit for both 24 and 93.5 °C. Delivered complete with certifieddiffuser stone,glassware, flowmeters and thermometers.

REF. 9416431Automatic time sequencer to monitor soaking, blowing and settling periodsfor 4 samples. It helps the operator to limit his presence nearby the instru-ment using audible and visual alarm.

ACCESSORIES

SPARE PARTS

ASTM D 892 Foaming Characteristics of Lubricating Oils


941643 - FOAMING TEST BATH


9416431 - AUTOMATIC SEQUENCER


99644 - WET TEST GAS METER24795 Dif fuser stone calibrated (w ith certif icate)

941644 Wet Test Gas Meter (type 00)

9416412 Graduated cylinder (1000 ml) w ith ballast9416433 A ir compressor

9411302 Borosilicate glass jar(300 x 450 mm)

19371 Graduated cylinder (1000 ml)




5 Kgw 260 mmd 260 mmh 460 mm

9417904 Pt 100 probe (160x5 mm)


24803 Stainless steel dif fuser

23203 Cryostat TLC 30 - 5 liters (-30/+60°C ±.1)

REF. 9416432Twin test unit for sequence 1, 2, 3 at 24 and 93.5 °C and sequence 4at150°C. Ready to use and delivered with two test cylinders, calibratedflowmeters and stainless steel diffusers.


SPARE PARTS


9416432 - FOAMING TESTER (150 °C)

9416434 Oil polyalphaolef in for bath (can of 25 l)

19371 Graduated cylinder (1000 ml)


9417905 Pt 100 probe (250x5 mm)

9416431 Automatic time sequencer

24803 Stainless steel dif fuser941435 Heating element (2000 W)

ASTM D 892 and D 6082Foaming caracteristics sequences 1, 2, 3 and 4

AMT

35


ASTM D 942 Oxidation Stability of Lubricating Greases(Oxygen Vessel Method)


SCOPEThis practice covers the laboratory determination, using a glass hydrom-eter, of the density, relative density, or API gravity of crude petroleum, pe-troleum products, or mixtures of petroleum and non petroleum productsnormally handled as liquids, and having a Reid vapor pressure of 26 lb orless.


ASTM D 941 Density and Relative Density of Liquids byLipkin Bicapillary Pycnometer

ASTM D 937 Cone Penetration of Petrolatum


SCOPEThis test method covers measuring with a penetrometer the penetration ofpetrolatum as an empirical measure of consistency.


SCOPEThis test method determines resistance of lubricating greases to oxidationwhen stored statically in an oxygen atmosphere in a sealed system at anelevated temperature under conditions of test.

OTHER STANDARDIP 142

REF. 941769Constant temperature oil bath, double walled,for 2 Norma-Hoffman Testvessels

REF. 941770Constant temperature oil bath, double walled,for 4 Norma-Hoffman Testvessels


SPARE PARTS


941770 - OIL BATH (4 places)

941766 Pressure gauge (0-160 psi)941767 Recording pressure gauge (2-pen) w ith tubings941370 Flexible polyethylene tubing w ith quick coupling941761 Complete oxidation vessel941762 Holder for 5 dishes517215 Glass dish (pack of 10)941764 Spare burst disc941765 Accessory for c losing vessel9417611 Complete oxidation vessel w ith burst disc11509 ASTM thermometer 22C

941762 Holder for 5 dishes517215 Glass dish (pack of 10)


9417641 Lead gasket for oxidation vessel


9417905 Pt 100 probe (250x5 mm)9417709 Heating element (1000 W)

941365 Charts for recording gauge (pack of 100)

9413621 Red Pen for recorder (pack of 5)9413622 Green Pen for recorder (pack of 5)

36


See other application under ASTM D 2274 - D 2893 - D 4310

SCOPEThis test method was developed for, and is used to evaluate the oxidationstability of inhibited steam-turbine oils in the presence of oxygen, water, andcopper and iron metals at an elevated temperature.


REF. 9416260 Oxidation Test apparatus, 8 units, with digital temperature display, opaquemagnetic screen, one bath thermometer.This apparatus is delivered whithout flowmeter.

STANDARD KITS AT CHOICE (REQUIRED)KIT FOR ASTM D 943 - 8 test positions

KIT FOR ASTM D 2274 & D 4310 - 8 test positions

KIT FOR ASTM D 2893 - 8 test positions


SPARE PARTS - GLASSWARE

SPARE PARTS - BATH

Apparatus for Filterable Insolubles (ASTM D2274 & D4310)

ASTM D 943 Oxidation Characteristics of InhibitedMineral Oils


9416260 - OXIDATION TESTER

21696 Oxidation cell D943/D2893 (8 cells requested)

21011 Catalyst iron-copper coil (ready to use)

516597 Reel of copper w ire catalyst (20 kg)516596 Reel of iron w ire catalyst (1 kg)

941628 Winding f ixture for w ire catalyst

9416232 Syringe w ith sampling tube9416231 Thermometer bracket

9416233 Sampling tube holder

19348 Mushroom condenser (D943)19349 Oxygen delivery tube

9416251 Flow meter for 3 l/h air (D943)

9416252 Flow meter for 3 l/h oxygen (D2274 / D4310)

9416253 Flow meter for 10 l/h air (D2893)



9417905 Pt 100 probe (250x5 mm)


19347 Test container

21697 Oxidation cell D 2274/D 4310 (8 cells requested)

19351 Mushroom condenser (D2274 / D4310)

27530 Filter 0.8 µm/diam. 47mm (D4310)28695 Vacuum pump 34 l/min. (D4310)30293 Filter assembly (D4310)

21696 Oxidation cell D943/D2893 (8 cells requested)

37



SCOPEThis test method specifies a procedure for the laboratory distillation of or-ganic liquids boiling between 30 and 300 °C which are chemically stableduring the distillation process.


ASTM D 1078 Distillation of Volatile Organic Liquids

SCOPEThis test method covers the determination of the loss in mass by evapora-tion of lubricating greases and oils for applications where evaporation lossis a factor.

REF. 941771Evaporation cell with grease sample cup, equipped with flowmeter andneedle control valve.

REF. 941772Evaporation cell with oil sample cup, equipped with flowmeter and needlecontrol valve.

OPTIONAL

SPARE PARTS

ASTM D 972 Evaporation Loss of Lubricating Greasesand Oils

9417741 Grease sample cup9417742 Oil sample cup11509 ASTM thermometer 22C11536 ASTM thermometer 67C

941773 Oil bath for evaporation cell

38


SCOPEThis test method covers the determination, at reduced pressures, of therange of boiling points for petroleum products that can be partially or com-pletely vaporized at a maximum liquid temperature of 400°C.

OTHER STANDARDSISO 6616

REF. 9411280Half-automated instrument built on a dedicated frame including water cir-culator, vacuum pump, computerized regulation of temperature and pres-sure (1 to 50 mmHg), printing dump of distillation report according to stand-ard and full glassware.


SPARE PARTS

ASTM D 1160 Distillation of Petroleum Products atReduced Pressure


9411280 - VACUUM DISTILLATION UNIT

SCOPEThis test method covers the determination of the water vapor content ofgaseous fuels by measurement of the dew-point temperature and the cal-culation therefrom of the water vapor content.

REF. 941975Complete Tester 3 to 15 psi with pressure gauge and thermometer.

REF. 9419751Complete Tester 0 to 350 psi with pressure gauge and thermometer.

SPARE PARTS

ASTM D 1142 Water Vapor Content of Gaseous Fuels byMeasurement of Dew-Point Temperature


941975 - WATER VAPOR TESTER

941977 Stainless steel mirror9419781 Bourdon manometer 3 to 15 psi9419782 Bourdon manometer 0 to 350 psi11515 ASTM thermometer 33C


41604 Set of glassw are

41609 500 ml glass f lask w ith thermow ell41611 200 ml cylinder for vacuum distillation41612 Distillation column and condenser41613 Dual cold trap9411304 V ac uum / Pt100 adapter ( top of c olumn)

9411306 Set of vacuum pipes

19011 Light recovery cylinder (12 ml)

41606 Heating block and mantle (1000 W)

23478 Quartz f lask w ith thermow ell (500 ml)


9417906 Pt 100 probe GDR (170x2 mm)

9411301 Distillation column "O" ring9411311 Seal gasket for Pt100



9411305 Distillation column for quartz f lask

21694 Heating controller

39



SCOPEThis test method covers the measurement of the density of pure hydrocar-bons or petroleum distillates boiling between 90 and 110°C that can behandled in a normal fashion as a liquid at the specified test temperatures of20 and 25°C.

ASTM D 1217 Density and Relative Density of Liquids byBingham Pycnometer

SCOPEThis test method covers the evaluation of the leakage tendencies of wheelbearing greases when tested under prescribed laboratory conditions.


ASTM D 1263 Leakage Tendencies of Automotive WheelBearing Greases


9411520 - FREEZING POINT APPARATUS

SCOPEThis test method covers the determination of the freezing point of engineantifreeze products.


REF. 9411520Freezing point apparatus of engine antifreeze solutions complete withthermometers.

SPARE PARTS

ASTM D 1177 Freezing Point of Antifreeze Products

23239 Dew ar f reezing tube (200 ml)9411522 Dew ar cooling bath15351 ASTM thermometer 75F15352 ASTM thermometer 76F


40


SCOPEThis practice covers the procedures for obtaining representative samplesof liquefied petroleum gases such as propane, butane, or mixture thereof,in containers other than those used in laboratory testing apparatus.

OTHER STANDARDSNFM 41101 - ISO 4257 - DIN 51610

REF. 9414541Whitey stainless steel sampling vessel (1gallon) complete assembly.

REF. 9412251Whitey stainless steel sampling vessel (2250cc) complete assembly.

REF. 9411001Whitey stainless steel sampling vessel (1000cc) complete assembly.

REF. 941501Whitey stainless steel sampling vessel (500 cc) complete assembly.

SPARE PARTS

ASTM D 1265 Sampling Liquefied Petroleum (LP) Gases(Manual Method)


SAMPLING OF LPG

SCOPEThis test method covers the evaluation of the resistance of a lubricatinggrease to washout by water from a bearing, when tested at 38 and 79°Cunder the prescribed laboratory conditions.


ASTM D 1264 Determining the Water WashoutCharacteristics of Lubricating Greases

941031 Valve D w ith tube 031 for ref . 9411001941034 Valve D w ith tube 034 for ref . 941501941046 Valve D w ith tube 046 for ref . 9412251941068 Valve D w ith tube 068 for ref . 9414541941400 Quick coupling (QQ-QF4-B-400)941440 Flexible tubing 1m (SS-TH4TA4PF4-40) 941464 Inlet valve C for vessel (SS-16DKM4-F4)9411613 Quick coupling male (SS-QF4-S-4PM) 9411819 Connection M/F TE (SS-4-ST) 9412213 Valve (SS-1 VM4)

9414546 Stainless steel sampling vessel (1gallon)9412250 Stainless steel sampling vessel (2250 cc)9411000 Stainless steel sampling vessel (1000 cc)9411000 Stainless steel sampling vessel (1000 cc)9411000 Stainless steel sampling vessel (1000 cc)941500 Stainless steel sampling vessel (500 cc)

41


ASTM D 1266 Sulfur in Petroleum Products(Lamp Method)


SCOPEThis test method covers the determination of total sulfur in liquid petroleumproducts in concentrations from 0.01 to 0.4 mass %.

OTHER STANDARDSIP 107 - NFM07031- ISO 2192 - DIN 51771

REF. 941454Sulfur determination apparatus in liquid petroleum products , complete6-unit assembly, by burning in a controlled atmosphere, suitable ManifoldSystem consisting of a vacuum manifold with regulating device and a dualmanifold supplying gas mixture of approx. 70% carbon dioxide (C0

2) and

30% oxygen (O2) at regulated pressures.

SPARE PARTS


941454 - SULFUR TESTER (lamp method)

19334 25 ml f lask (non aromatic products)19332 Burner for non-aromatic samples

19331 Chimney19330 Absorber 19333 Spray trap

19013 Scrubber19014 Regulator tube9414568 Pressure or vacuum trap9414570 Level f lask19336 25 ml f lask (aromatic products)19335 Burner for aromatic samples

56 Kgw 1150 mmd 600 mmh 800 mm

9414560 Ball of 2 oz cotton w icks, 4 strands

42


SCOPEThis test method covers the determination of the gage vapor pressures ofliquefied petroleum gas products at temperatures of 37.8°C up to 70°C.


REF. 941432Electronic constant thermostatic bath, 3 vessels capacity, with thermom-eter and digital display. Equipped with adjustable stirring device, low watercut-off, cooling coil for external cryostat and drain cock.

LPG TEST VESSEL (for D1267)

LPG TEST VESSEL (for IP 161)

OPTIONAL ACCESSORY

VAPOR PRESSURE GAUGES (psi and kPa)

SPARE PARTS

ASTM D 1267 Gauge Vapor Pressure of LiquefiedPetroleum Gases (LP-Gas Method)


941921 - LPG TEST VESSEL


SCOPEThis practice covers the laboratory determination, using a glass hydrom-eter, of the density, relative density, or API gravity of crude petroleum, pe-troleum products, or mixtures of petroleum and nonpetroleum productsnormally handled as liquids, and having a Reid vapor pressure of 26 lb orless.


ASTM D 1298 API Gravity of Crude Petroleum and LiquidPetroleum Products by Hydrometer

941921 LPG test vessel

9419221 Test vessel up to 300 psi (20% capacity)9419222 Test vessel above 300 psi (20% capacity) 9419231 Test vessel up to 300 psi (33% capacity) 9419232 Test vessel above 300 psi (33% capacity)

941920 Safety burst disk capsule (add on vessel price)

941424 Metallic manometer 0 to 100 psi/650 kPa941918 Metallic manometer 0 to 500 psi/3400 kPa

941925 Metallic manometer 0 to 250 psi/1600 kPa

9419201 Spare burst disc

9419211 A ir chamber w ith valve for 9419219419212 Gas chamber w ith 2 valves for 941921 9419213 Gasket for LPG vessel D1267 (pack of 24)9419237 Seal "O" ring for IP161 test vessel 11505 ASTM thermometer 18C





9417905 Pt 100 probe (250x5 mm)

43


SCOPEThis test method is for determining hydrocarbon types over the concentra-tion ranges from 5 to 99 volume % aromatics, 0.3 to 55 volume % olefins,and 1 to 95 volume % saturates in petroleum fractions that distill below315°C.


REF. 941600New designed adsorption apparatus assembly, 4 test, with pressure gauges,needles valves, UV lighting, vibrator and basic glassware whithout column .


SPARE PARTS

ASTM D 1319 Hydrocarbon Types in Liquid PetroleumProducts by Fluorescent Indicator Adsorption


941600 - ADSORPTION APPARATUS

ASTM D 1321 Needle Penetration of Petroleum Waxes


SCOPEThis test method covers the empirical estimation of the consistency of waxesderived from petroleum by measurement of the extent of penetration of astandard needle.

OTHER STANDARDSNFT 60123 - ISO 3992 - DIN 51579

19761 Silica gel 100 to 200 mesh (2 kg)76239 Certif ied s ilica gel w ith colored indicator (40 gr)

19585 Hypodermic syringe 1ml

9415068 Hypodermic c leaning tube (2 m)

9415057 Tube UV (40 W)

21700 Standard adsorption column (upper part)

19022 Spherical connector for air input (S28/12)

19023 Standard w all tubing (low er part)

19582 Outlet for true bore column (S12/2)

11089 Clamp for low er joint11091 Clamp for upper joint


9415059 Electrical vibrator

19586 Hypodermic needle 102 mm (set of 5)

19325 True Bore adsorption column

44


SCOPEThis test method covers measurement of the ability of petroleum oils orsynthetic fluids to separate from water.

OTHER STANDARDSNFT 60125 - ISO 6614

REF. 941550Automated Demulsibility Tester, CE tested and approved, controlled byexclusive software with image processing, with a highest degree ofrepeatability and reproducibility because layers detections are no longerevaluated by the human eyes but by using a CCD-Camera which takespictures of every sample tube during testing

SPARE PARTS

REF. 941545Semi-automatic demulsibility tester microprocessored controlled , threetest unit, electronic temperature control between 20 and 95°C ± 0.1°C,stirring speed and time control with digital parameters display, moving steelshaft with stirring motor, paddle and inside illumination.

SPARE PARTS

ASTM D 1401 Water Separability of Petroleum Oils andSynthetic Fluids


941550 - AUTO DEMULSIBILITY TESTER


941545 - DEMULSIBILITY TESTER

SCOPEThis test method covers a procedure for determination of the smoke pointof kerosine and aviation turbine fuel.


REF. 941680Smoke point apparatus, complete, delivered with one interchangeable oilcontainer

SPARE PARTS

ASTM D 1322 Smoke Point of Kerosine and AviationTurbine fuel


941680 - SMOKE POINT APPARATUS

9416801 Candle (oil container)9416802 Wick (pack of 12)

9415450 Stirring paddle

11470 Glass graduated cylinder (100 ml)


941551 Translucent plate for bath bottom

4 Kgw 200 mmd 200 mmh 400 mm



9417901 Pt 100 probe (150x6 mm)

11470 Glass graduated cylinder (100 ml)9415450 Stirring paddle

9417904 Pt 100 probe (160x5 mm)



45



SCOPEThis test method describes two procedures for the measurement of thedensity of materials which are fluid at the desired test temperature.

ASTM D 1480 Density and Relative Density of ViscousMaterials by Bingham Pycnometer

SCOPEThis test method covers the determination of the extent to which a greaseretards the rotation of a slow-speed ball bearing by measuring starting andrunning torques at low temperatures (below -20°C).


ASTM D 1478 Low-Temperature Torque of BallBearing Grease

ASTM D 1403 Cone Penetration of Lubricating GreaseUsing 1/4 and 1/2 Scale Cone Equipment


SCOPEThis test method covers two procedures for measuring the consistency ofsmall samples of lubricating greases by penetration of a ¼ or ½ scale cone.


46


SCOPEThis test method covers three procedures for the determination of totalsulfur in petroleum products including lubricating oils containing additives,and in additive concentrates.

OTHER STANDARDNFM 07025

REF. 941450Equipment including electric tube furnace with microprocessored digitalsetting and reading, gas washing bottles, calibrated flowmeter, porcelaincombustion tube, combustion boats, boat pusher, bent tube, absorber,burettes with support and clamps.

SPARE PARTS

ASTM D 1552 Sulfur in Petroleum Products(High-Temperature Method)


941450 - HIGH TEMPERATURE SULFUR TESTER

9414012 Boat pusher9414024 Combustion boat (alundum)9414062 Combustion tube 9414501 Heating element for furnace9414003 Oxygen drying train (3 f lask)

941472 Burette (25 ml in 0.1ml)

19015 Right angle connector w ith standard joint19330 Absorber


SCOPEThis test method covers the visual determination of the color of a widevariety of petroleum products such as lubricating oils, heating oils, dieselfuel oils, and petroleum waxes.


REF. 24415Manual colorimeter model AF650 with a 16 filters colorimetric scale from0.5 to 8.0 units. It is a 3-field instrument for visually determining the ASTMcolour of samples by direct comparison with coloured glass standards. Theinstrument is delivered with 3 glass sample jars and a calibration certificatefor the filters.

SPARE PARTS

AUTOMATIC APPARATUSREF. 29056 ON REQUESTThe Lovibond PFX 190 is an easy to use, automatic instrument requiringno special skills to operate. It is supplied complete with Windowssoftware, accessories and spares, optical glass cells for the colour scalesincluded. Additional scales can be added to standard instruments onrequest.

REF. 29006 ON REQUESTThe Lovibond PFX 880/P is an easy to use, automatic instrument, whicheliminates time-consuming procedures of visual methods. It is aspectrophotometer for objective colour analysis of petroleum fuels, oils,waxes and petrochemicals according to the Saybolt and ASTM Colourscales

ASTM D 1500 ASTM Color of Petroleum Products(ASTM Color Scale)


24415 - COLORIMETER AF650

115/230 V0.3 A50 Hz5.5 Kgw 255 mmd 250 mmh 170 mm

19353 Glass sample tube22279 Halogen lamp 12V / 20W

47


SCOPEThis test method covers the determination of the relative density or densityof light hydrocarbons including liquefied petroleum gases (LPG).

OTHER STANDARDSIP 235 - NFM 41008 - ISO 3993

REF. 941911Complete apparatus, mounted on a heavy base and suitable for immersionin a constant temperature water bath.

REF. 9419110Complete apparatus with burst disk, mounted on a heavy base and suitablefor immersion in a constant temperature water bath.


OPTIONAL ACCESSORY

SPARE PARTS

SCOPEThis test method covers the determination of the relative density or densityof light hydrocarbons including liquefied petroleum gases (LPG).

REF. 272351 -Place Engler viscometer without accessorieselectric heatingdigital display of temperaturetemperature from room up to + 99,9°Cpolished brass test cup with stainless steel efflux tubewaterbath motor stirrer 2800 rpmsafety thermostatecooling coil


ASTM D 1657 Density or Relative Density of Light Hydro-carbons by Pressure Thermohydrometer


941911 - TEST VESSEL

941432 Constant temperature w ater bath (3 test)

9419121 Thermo-hydrometer (0.500 to 0.650 in °F)

23448 Thermodensimeter (0.500 à 0.550 - 30°C)23449 Thermodensimeter (0.550 à 0.600 - 30°C)

9419132 Lucite transparent cylinder

9419133 Neoprene gasket

9419124 Thermometer ISO 653






9417905 Pt 100 probe (250x5 mm)


ASTM D 1665 Engler Viscometer for Bitumen


27235 - ENGLER VISCOMETER


521155 Engler f lask 50 ml27253 Engler f lask 100 + 100 ml 27254 Engler f lask 200 + 40 ml 27251 Engler thermometer w ith ring +10/+55°C in 0.5°C27252 Engler thermometer w ith ring +10/+110°C in 1°C

48


SCOPEThis test method is used for evaluating the rust-preventive properties ofmetal preservatives under conditions of high humidity.


ASTM D 1748 Rust Protection by Metal Preservatives in theHumidity Cabinet

SCOPEThis test method covers the determination of the tendency of a lubricatinggrease to separate oil during storage in both normally filled and partiallyfilled containers.

REF. 9417786-test unit apparatus, complete, including air-pressure reducing valve andregulator, constant temperature oven, bleeding cups with cover and sievestrainers, with thermometer.

SPARE PARTS

ASTM D 1742 Oil Separation from Lubricating Greaseduring Storage

9417781 200 mesh stainless steel s ieve (type A )12434 Beaker (20 ml)

11492 ASTM thermometer 5C9418779 Heating element (500 W)

941778 - OIL SEPARATION FROM GREASE



49


ASTM D 1831 Roll Stability of Lubricating Grease

SCOPEThis test method covers determination of the changes in the consistency,as measured by cone penetration, of lubricating greases when worked inthe roll stability test apparatus.

REF. 941744Specially designed twin-unit for long runs at high temperature up to 150 °C.Delivered with 2 rolls/cylinders, tools and gloves.

ACCESSORIES

SPARE PARTS


SCOPEThis test method covers the laboratory test for determination of water andsediment in fuel oils by using the centrifuge method in the range from 0 to30 % volume.


ASTM D 1796 Water and Sediment in Fuel Oils by theCentrifuge Method (Laboratory Procedure)

ASTM D 1754 Effects of Heat and Air on AsphalticMaterials (Thin-Film oven Test)

SCOPEThis test method covers the determination of the effects of heat and air ona film of semisolid asphaltic materials.

OTHER STANDARDNF EN 12607-2

REF. 941876Strictly conform to ASTM requirements, this is a double wall illuminatedoven with glass window, 4 place revolving shelf, 4 aluminium containersand thermometer.

ACCESSORY

SPARE PARTS


941744 - ROLL STABILITY TESTER

9417441 Lubricating grease pump for bearing (500g)9417442 Roller gasket

9417443 Stopper 50/56 x 51 mm9417444 Gloves (pair)9417445 Bearing

230 V10 A50 Hz75 Kgw 600 mmd 570 mmh 520 mmon request115V 60Hz9417834 Pt 100 probe (60x3.15 mm)

941876 - THIN FILM OVEN


9418762 Bulb 230V /15W11500 ASTM thermometer 13C

9418761 A luminium sample container 140x10 mm


50


SCOPEThis test method covers the removal of pentanes and lighter hydrocarbonsfrom gasolines, naphthas and similar petroleum distillates to prepare sam-ples suitable for the determination of hydrocarbon types in accordance withTest Method D 1319 or Test Method D 2789.

REF. 21593Depentanization apparatus complete

SPARE PARTS

ASTM D 2001 Depentanization of Gasoline and Naphthas

SCOPEThis test method detects the presence of components in liquefied petro-leum gases which may be corrosive to copper.


REF. 941432Electronic constant thermostatic bath , 3 vessels capacity, with thermom-eter and digital display. Equipped with adjustable stirring device, low watercut-off, cooling coil for external cryostat and drain cock.


SPARE PARTS

ASTM D 1838 Copper Strip Corrosion by LiquefiedPetroleum (LP) Gases


24541 Single strip polishing vise15114 Copper strip corrosion test standard


11499 ASTM thermometer 12C22505 Silicon carbide pow der 150 mesh (1 kg)

941905 Corrosion test vessel (150 x 38 mm)941906 Suspension for test cylinder

9414850 Copper strip semi-f inished w ith hole (pack of 24)


11499 ASTM thermometer 12C22505 Silicon carbide pow der 150 mesh (1 kg)

9414850 Copper strip semi-f inished w ith hole (pack of 24)

SCOPEThis test method is a measure of the relative purity of the various types ofliquefied petroleum (LP) gases and helps to ensure suitable volatility per-formance.

OTHER STANDARDSNFM41012 - ISO 6620

REF. 941940Complete apparatus, with test tube, 2 Dewar flasks and armored ther-mometer

SPARE PARTS

ASTM D 1837 Volatility of Liquefied Petroleum (LP) Gases


941940 - TESTER FOR LPG

941942 Unsilvered Dew ar f lask15164 ASTM thermometer 99C




9417905 Pt 100 probe (250x5 mm)

15165 Sleeve for 99C thermometer

941909 Spare gasket for test vessel (pack of 10)

19398 Set of glassw are for depentanization

19350 Weathering cone shaped tube

51


SCOPEThis test method describes a procedure for determining the filter blockingtendency (FBT) of distillate fuel oils where the end use demands an excep-tional degree of cleanliness.


REF. 41800Automatic portable model NBF 241 with printer for determining the FBT.The pressure/flow curve is printed at the end of the test as well as thecalculation type and results.

REF. 41801Automatic bench top model NBF 240 with printerfor determining the FBT.The pressure/flow curve is printed at the end of the test as well as thecalculation type and results.

SPARE PARTS

ASTM D 2068 Filter Blocking Tendency of Distillate FuelOils


41800 - PORTABLE MODEL NBF 241


41801 - BENCH TOP MODEL NBF 240

SCOPEThis practice covers the isolation of a representative saturates fraction fromdepentanized hydrocarbon mixtures that distil below 221°C.

REF. 19400High efficiency column

ACCESSORY

ASTM D 2003 Isolation of Representative Saturates Frac-tion from High-Olefinic Petroleum Naphthas

SCOPEThis practice covers the isolation of a representative saturates fraction fromdepentanized hydrocarbon mixtures that distil below 221°C and that con-tain less than 1 volume percent of olefinic hydrocarbons.

REF. 19399Complete adsorption column for low olefinic concentration

ASTM D 2002 Isolation of Representative Saturates Frac-tion from Low-Olefinic Petroleum Naphthas

13603 Spherical ground joint w ith nipple



40390 Printer paper Seyko DPU 414 (roll)27773 Filter in f iberglas s (s et of 100)12450 Beaker tall form (400 ml)

41803 Pt100 probe41805 Filter holder stainless steel41810 Tef lon gasket and grating (kit)41811 Tygon tube 0.8 mm diam. (15 m roll)

52


ASTM D 2112 Oxidation Stability of Inhibited MineralInsulating Oil by Rotating Bomb


SCOPEThis test method utilizes an oxygen-pressured bomb to evaluate the oxida-tion stability of inhibited mineral oils.

REF. 9416298Oil thermostatic bath for 2 rotating test vessels



SPARE PARTS

SCOPEThis test method covers the determination of the extraneous materials weath-ering above 38°C that are present in liquefied petroleum gases.


REF. 941957Apparatus for determining the extraneous residues above 100°FComplete with thermometer 57C.

SPARE PARTS

ASTM D 2158 Residues in Liquefied Petroleum (LP) Gases


941957 - TESTER FOR LPG

941942 Unsilvered Dew ar f lask




9416298 - OXIDATION STABILITY

21339 Catalyst copper coil (ready to use)9416303 Charts for pressure recorder (pack of 60)9416293 Sample container w ith tef lon cover

9416300 "O" ring for vessel cover

21339 Catalyst copper coil (ready to use)9416292 Pressure recorder (1 per vessel)9416291 Oxidation vessel (stainless steel)9416293 Sample container w ith tef lon cover9416295 Tef lon cover for glass sample container9416296 Tef lon disc to be placed under sample container11554 ASTM thermometer 96C

9416301 Support rack for 2 vessels

9416297 Pen for recorder

19350 Weathering cone shaped tube

53


SCOPEThis test method covers the determination of the dropping point of lubricat-ing grease.

OTHER STANDARDISO 6299

ASTM D 2265 Dropping Point of Lubricating Grease OverWide Temperature Range


See other application under ASTM D 2669 - D 2983 - D 4287

SCOPEThis test method covers the determination of rheological properties of non-newtonian materials by rotational (Brookfield) viscometer.


ASTM D 2196 Rheological Properties of Non-NewtonianMaterials by Rotational Viscometer

ASTM D 2272 Oxydation Stability of Steam Turbine Oils byRotating Bomb


SCOPEThis test method utilizes an oxygen-pressured bomb to evaluate the oxida-tion stability of new and in service turbine oils having the same composition(base stock and additives) in the presence of water and a copper catalystcoilm at 150°C.



SCOPEThis test method covers the determination of trace amounts (less than 0.05volume %) of sediment in lubricating oils.

ASTM D 2273 Trace Sediment in Lubricating Oils


SCOPEThis test method covers the measurement of inherent stability of middledistillate petroleum fuel under accelerated oxidizing conditions.


ASTM D 2274 Oxidation Stability of Distillate Fuel Oil(Accelerated Method)

54


SCOPEThis test method covers the determination of the temperature below whichsolid hydrocarbon crystals may form in aviation turbine fuels and aviationgasoline.


REF.941556Complete manual freezing point apparatus, comprising : jacketed sampletube, brass packing gland for stirrer, brass wire stirrer, vacuum flaskunsilvered with support and thermometer.


SPARE PARTS

NECESSARY ACCESSORY

AUTOMATIC INSTRUMENT

Special standard on request for dedicated territories

ASTM D 2386 Freezing Point of Aviation Fuels


941556 - FREEZING POINT

513462 Jacketed sample tube (double w alls)9415562 Gland, brass packing for stirrer9415563 Stirrer9415564 Vacuum f lask unsilvered11566 ASTM thermometer 114C513463 Cork for sample tube

5 Kgw 200 mmd 200 mmh 450 mm


55


SCOPEThis test method indicates the tendency of a mineral insulating oil to deterio-rate on oxidation under specified conditions.

REF. 94165012-test aluminium block bath with electronic controller with digital tempera-ture display and setting, using PT 100 sensor. Temperature can be adjustedbetween 50 and 210°C +/- 0,5°C to comply with standards requests.This instrument is delivered without flowmeter and thermometer. (12 of each must be ordered separately).This instrument is delivered without glassware. (24 of each must be ordered separately).


SPARE PARTS

ASTM D 2440 Oxidation Stability of Mineral Insulating Oil

See other application under IP 48 - IP 280 - IP 306 - IP 307 - IP 335


941650 - OXIDATION STABILITY TESTER

9416501 Flow meter for 15 l/h air (IP48)9416502 Flow meter for 1 l/h oxygen (IP 280-306-307-335)19375 Glassw are for ALL methods (each)

19375 Glassw are for ALL methods (each)

SCOPEThis test method covers the detection of hydrogen sulfide in liquified petro-leum (LP) gases.

OTHER STANDARDNFM 41011

REF. 941958Apparatus for hydrogen sulfide in liquefied petroleum gases

SPARE PARTS

ASTM D 2420 Hydrogen Sulfide in Liquefied Petroleum(LP) Gases (Lead Acetate Method)


941958 - HYDROGEN SULFIDE TESTER

9419581 Set of glassw are


230 V10•6 A50 Hz55 Kgw 650 mmd 620 mmh 860 mmon request115V 60Hz25959 IP thermometer 81C

25959 IP thermometer 81C





9417834 Pt 100 probe (60x3.15 mm)9416508 Heating element (1500 W)


56


SCOPEThis test method covers the determination of evaporation loss of lubricatinggreases at temperatures between 93 and 316°C.


ASTM D 2595 Evaporation Loss of Lubricating Greases OverWide-Temperature Range


SCOPEThis test method covers only petroleum products which are transparent inlayers 40mm in thickness, and with a cloud point below 49°C.


ASTM D 2500 Cloud Point of Petroleum Products

57


SCOPEThis test method covers the determination of the electrical conductivity ofaviation and distillate fuels with and without a static dissipator additive.


REF. 23628Portable Conductivity meter

SPARE PART

ASTM D 2624 Electrical Conductivity of Aviation andDistillate Fuels

SCOPEThis test method covers the determination of the hydrolytic stability of pe-troleum or synthetic-base hydraulic fluids.

REF. 941995Oven complete with filtration assembly, 12 bottles, crown cork, copper stripsand protections.

SPARE PARTS

ASTM D 2619 Hydrolytic Stability of Hydraulic Fluids(Beverage Bottle Method)


SCOPEThis test method covers the laboratory determination of apparent viscosityof engine oils at 0°F and at high shear rates.

OTHER STANDARDDIN 51377


ASTM D 2602 Apparent Viscosity of Engine Oils Using theCold-Cranking Simulator

27532 Membrane f ilters (pack of 100)941952 Caps w ith inert seals (pack of 100)941953 Bottle (200 ml)9419954 Copper strips (pack of 20)9419955 Heating elements for oven (per set of 8)

23629 Carbon/zinc spare battery (9 V )


23628 - CONDUCTIVITY METER

Battery V AHz

5 Kgw 400 mmd 210 mmh 150 mm


941995 - HYDROLYTIC STABILITY



58



SCOPEThis test method covers the determination of the knock characteristics ofmotor gasolines, intended for use in spark-ignition engines, in terms of ASTM-IP research octane numbers.


ASTM D 2699 Knock Characteristics of Motor by theResearch Method


SCOPEThis test method covers the determination of the knock characteristics ofmotor and aviation gasolines, intended for use in spark-ignition engines.


ASTM D 2700 Knock Characteristics of Motor and AviationFuels by the Motor Method

ASTM D 2669 Apparent Viscosity of Petroleum WaxesCompounded with Additives (Hot Melts)

See instrument under under ASTM D 2196

SCOPEThis test method covers the determination of the apparent viscosity of pe-troleum waxes compounded with additives (hot melts).

59


ASTM D 2872 Effect of Heat and Air on a Moving Film ofAsphalt (RTFOT)

SCOPEThis test method is intended to measure the effect of heat and air on amoving film of semisolid asphaltic materials.

OTHER STANDARDNF EN 12607-1

REF. 941877Double wall illuminated oven with glass window, 8 places revolving verticalshelf, 8 glass containers, thermometer and instruction manual.

SPARE PARTS

SCOPEThis test method covers the determination of total sulfur in liquefied petro-leum gases containing more than 1µg/g.


REF. 24516The testerwith metallic structure includes stainless steel (not quartz) oxi-hydrogen burner, quartz combustion chamber cooled by water, gas supplysystem with flowmeters and adjustment valves, gas safeties, dry vacuumpump and protective screen, delivered without glassware


SPARE PARTS

ASTM D 2784 Sulfur in Liquefied Petroleum Gases(Oxy-Hydrogen Burner Method)

23680 Standardized glass container9418762 Bulb 230V /15W

11500 ASTM thermometer 13C9418779 Heating element (500 W)


24516 - WICKBOLD TESTER


21343 Set of glassw are for Wickbold Tester21344 Liquef ied gas cylinder w ith valves

20928 Quartz combustion chamber20983 Absorber w ith f ritted plate20984 Trap


941877 - OVEN “RTFOT”



10688 Stainless steel burner oxygen / hydrogen


21344 - LPG CYLINDER

60


SCOPEThis test method covers the determination of salts in crude oil.


REF. 942287Complete salt-in-crude analyzer with test cell, electrode assembly and testleads, digital autoranging meter for reading the voltage and current.

SPARE PARTS

ASTM D 3230 Salts in Crude Oil (Electrometric Method)


942287 - CRUDE OIL ANALYZER NSB 210

SCOPEThis test method describes the use of the Brookfield viscometer for thedetermination of the low-shear-rate viscosity of automotive fluid lubricantsin the temperature range from -5 to -40°C.



BROOKFIELD VISCOMETERS (See ASTM D 2196)

ASTM D 2983 Low-Temperature Viscosity of AutomotiveFluid Lubricants (Brookfield Viscometer)


SCOPEThis test method covers the determination of solvent extractables in petro-leum waxes.

ASTM D 3235 Solvent Extractables in Petroleum Waxes

19035 Test cell9412871 Electrode w ith cover



SCOPEThis test method covers determination of the oxidation characteristics ofextreme-pressure fluid lubricants, gear oils, or mineral oils.

ASTM D 2893 Oxidation Characteristics of ExtremePressure Lubricating Oils

61


SCOPEThis test method covers the ability of a petroleum-type steam turbine oil toseparate entrained air.


REF. 941688Complete equipment for determination of the ability of an oil to separateentrained air in hydraulic, turbine and other lubricating oils.

ACCESSORIES

SPARE PARTS

ASTM D 3427 Air Release Properties of Petroleum Oils


941688 - IMPINGER TEST RIG


SCOPEThis test method covers the determination of flash points of liquids by theSetaflash closed cup tester .

ASTM D 3278 Flash Points of Liquids by Setaflash-Closed-Cup Apparatus




12628 5 ml plunger12629 10 ml plunger9416885 Balance w ith acquis ition sof tw are (62 g / 0.1 mg)

12627 Sample glassw are complete


9417834 Pt 100 probe (60x3.15 mm)

21375 Electronic stopw atch


62



SCOPEThis test method provides a rapid portable means for field and laboratoryuse to rate the ability of aviation turbine fuels to release entrained or emul-sified water when passed through fiberglass coalescing material.

ASTM D 3948 Water Separation Characteristics of AviationTurbine Fuels by Portable Separometer


SCOPEThis test method describes the laboratory determination of water and sedi-ment in crude oils by means of the centrifuge procedure.

ASTM D 4007 Water and Sediment in Crude Oil by theCentrifuge Method (Laboratory Procedure)


SCOPEThis test method covers the prediction of the borderline pumping tempera-ture (BPT) of engine oils through the use of a 16 h cooling cycle over thetemperature range from 0 to -40°C.

OTHER STANDARDSAE J300


ASTM D 3829 Predicting the Borderline PumpingTemperature of Engine Oil


SCOPEThis test method covers procedure for the determination of the flash pointby a small scale closed tester.


ASTM D 3828 Flash Points by Small Scale Closed Tester


63


SCOPEThis practice covers procedures for manually obtaining representative sam-ples of petroleum products of a liquid, semi-liquid, or solid state whose vaporpressure at ambient conditions is below 101 kPa.


REF. 22213 Brass weighted bottle, neck 19mm.

REF. 22214Brass weighted bottle, neck 38mm

REF. 519032Sampling thief, bomb type (1 liter) diameter 80 mm.


ASTM D 4057 Manual Sampling of Petroleum andPetroleum Products


22213 - SAMPLING BOTTLE

ASTM D 4287 High-Shear Viscosity Using the ICICone/Plate Viscometer


SCOPEThis test method covers the determination of high-shear viscosity using theICI cone/plate viscometer.


SCOPEThis test method covers the determination of water in the range from 0.02to 2% in crude oils.


ASTM D 4377 Water in Crude Oils by Potentiometric KarlFischer Titration

519037 Chain nickel-plated brass 25 m length519039 Nylon cable 50 m length


SCOPEThis test method is used to evaluate the tendency of inhibited mineral oilbased steam turbine lubricants and mineral oil based anti-wear hydraulicoils to corrode copper catalyst metal and to form sludge during oxidation inthe presence of oxygen, water, and copper and iron metals at an elevatedtemperature.

ASTM D 4310 Sludging and Corrosion Tendencies ofInhibited Mineral Oils

64


See other application under ASTM D 189 - D 482

SCOPEThis test method covers the determination of the amount of carbon residueformed after evaporation and pyrolisis of petroleum materials under certainconditions and is intended to provide some indication of the relative cokeforming tendency of such materials.

OTHER STANDARDSIP 398 - ISO 10370 - DIN 51551

REF. 41023The NMC 440 model, fully automatic tester, provides 3 preset methodsplus 17 additional ones with 4 heating segments. It performs Conradsontest up to 750°C under automatic controlled atmosphere. Test report in-cluding weights, results and temperature curve printed on the delivered printeror send to computer throught RS232C output.

MAIN CONSUMABLES

SPARE PARTS

REF. 941670The NMC 210, automatic apparatus only for the standard D 4530 isdelivered ready to use equipped with accessories (2ml vial, holder forvial, cleaning cable, holder hook). The test is performed automaticallyunder atmosphere controlled by programmed controller.


MAIN CONSUMABLES

SPARE PARTS

ASTM D 4530 Determination of Carbon Residue( M C R T )


41023 - MICRO CONRADSON NMC 440


941670 - MICRO CONRADSON NMC 210

230 V10 A50 Hz15 Kgw 250 mmd 300 mmh 600 mmon request115V 60Hz picture not mandatory

41001 2 ml borosilicate glass sample vial (D 4530)41002 16 ml borosilicate glass sample v ial (D 4530)

41004 16 ml quartz sample vial ash content (re-usable)41003 2 ml quartz sample v ial ash content (re-usable)

41025 Gas connection kit-2 gas outputs

41026 4 ml borosilicate glass sample tube (ISO 10370)

41027 Holder for 25-50-100 g. porcelain crucibles

10510 Porcelain crucible,120 ml tall form (pack of 6 )

10508 Porcelain crucible, 40 ml tall form (pack of 6 )10515 Porcelain crucible, 80 ml low form (pack of 6 )


41046 16 ml v ials (pack of 144) for s ingle use41047 2 ml vials (pack of 144) for single use

941669 Regulation thermocouple941668 Solenoid valve for air

941667 Solenoid valve for nitrogen

41001 2 ml borosilicate glass sample vial (D 4530)41002 16 ml borosilicate glass sample v ial (D 4530)

41005 Holder for v ial 2 ml (12x)

41006 Holder f or v ial 16 ml (6x )

41007 Mixed holder 2 and 16 ml (7x)

41004 16 ml quartz sample vial ash content (re-usable)41003 2 ml quartz sample v ial ash content (re-usable)

41046 16 ml v ials (pack of 144) for s ingle use41047 2 ml vials (pack of 144) for single use

65



SCOPEThis test method covers the measurement of the yield stress and viscosityof engine oils after cooling at controlled rate over a period exceeding 45 hto a final test temperature between -10 and -40°C.

ASTM D 4684 Determination of Yield Stress and ApparentViscosity of Engine Oils at Low Temperature


SCOPEThis test method provides a rapid, portable means for field and laboratoryuse to visually inspect for particulate matter and numerically rate free waterin aviation turbine and distillate fuels.

ASTM D 4860 Free Water and Particulate Contamination inMid-Distillate Fuels (Clear and Bright Rating)

SCOPEThis test method determines the temperature at which an oil can becomeunsuitable for lubrication of a mechanical device such as an engine, be-cause of insufficient flow of the bulk oil in the sump to the oil screen.


ASTM D 5133 Temperature Dependence of Lubricating OilsUsing a Temperature-Scanning Technique

SCOPEThis test method covers the use of automated vapor pressure instrumentsto determine the total vapor pressure exerted in vacuum by air-containing,volatile, liquid petroleum products.


ASTM D 5191 Vapor Pressure of Petroleum Products(Mini Method)

66


SCOPEThis test method covers a procedure for determining the evaporation lossof lubricating oils (engine oils) using the Noack evaporative tester.

OTHER STANDARDSNFT 60161 - DIN 51581- CEC L40 A93

REF. 941783Evaporative capacity tester for lubricating oils, complete with P I D tem-perature regulator, set of glassware, manometer and liquid, one cruciblewith tools, one pair protecting gloves, thermometer with certificate.


SPARE PARTS

ASTM D 5800 Evaporation Loss of Lubricating Oils by theNoack Method


941783 - NOACK TESTER


SCOPEThis test method covers the laboratory determination of apparent viscosityof engine oils at temperatures between -5 and -30°C at shear stresses ofapproximately 50000 to 100000 Pa and shear rates of approximately 100000to 10000 s-1 and viscosities of approximately 500 to 10000 mPa*s.

ASTM D 5293 Apparent Viscosity of Engine Oils Using theCold-Cranking Simulator

ASTM D 6082 High Temperature Foaming Characteristicsof Lubricating Oils


SCOPEThis test method describes the procedure for determining the foaming char-acteristics of lubricating oils (specifically transmission fluid andmotor oil) at 150 °C.

9417837 Standardization oil RL 172/5 (1 liter)9417838 Vacuum pump model ME2C9417831 Automated vacuum controller9417832 Graphic data recorder and printer21375 Electronic stopw atch

2094802 Wood metal (250g)9417830 Heating element (set of 2)9417834 Pt 100 probe (60x3.15 mm)9417835 Stainless steel crucible9417836 Set of glassw are

23190 Thermometer w ith certif icate (+40/+260°C)

14089 silicon tubing inside diam. 4 mm (1 meter)


9417907 Pt 100 probe GDR (120x2 mm)


67


ASTM D 6371 Cold Filter Plugging Point

See other application under IP 309 - IP 419

SCOPEThis test method covers the determination of the cold filter plugging point(CFPP) of diesel and domestic heating fuels using either manual or auto-mated test equipment.

REF. 20878This model, single unit includes double wall bath with insulation, jacket, testtube, insulating ring and spaces, jacket stand, 3-hole stopper, pipet, filtra-tion set and thermometers. Cooling is achieved by dry ice machine.

REF. 20886This model, single unit includes double wall bath with insulation, jacket, testtube, insulating ring and spaces, jacket stand, 3-hole stopper, pipet, filtra-tion set and thermometers. It is equipped with a cooling coil to be connectedon a cryostate.


SPARE PARTS

REF. 60200NTL 450 is delivered complete with necessary glassware, tempera-ture probe, printer and instruction manual.- Detection by specific optical cells- Visualisation of the different cooling steps- Possibility to use a programmed linear cooling slope- Quick fixation on measuring head- Visualisation of the sucking up time & release time sample- Easy access to maintenance paramaters by software- Easy access to hardware maintenance- Electronic vacuum regulation with 15 litres per hour

NECESSARY ACCESSORY

SPARE PARTS

27502 Vacuum pump20879 Vacuum regulator + manometer + 3w ay cock

17885 CFPP test tube20880 Jacket20881 Pipet for manual apparatus20882 Filtration device11492 ASTM thermometer 5C11493 ASTM thermometer 6C

23205 Cryostat TLC 80 - 11 liters (-80/+20°C ±.05)941597 Dry ice machine


60200 - CFPP MODEL NTL 450

230 VA

50 Hz25 Kgw 270 mmd 500 mmh 600 mm


CFPP MODEL NTL 450 - screen shot


17885 CFPP test tube20882 Filtration device21916 CFPP pipet40809 Basket for tube (set of 2)40822 45µ Filter on ring

68


SCOPEThe method is primarily intended for the determination of the viscosity ofany petroleum product which flows in a Newtonian manner, i.e. possessesa linear relationship between shearing stress and rate of shear under theconditions of the test.

REF. 272411-PLACE REDWOOD VISCOMETERapparatus for determination of viscosity as a time of flow (30-2000s)main features :* electronic temperature controller with digital display* test temperature range : from room up to 93,3°C (+/- 0,2°C)* polished brass calibrated cup with cover and stainless steel orifice* water bath with cover and cooling coilApparatus delivered whithout accessories


IP 70 Redwood Viscosity

SCOPEThis test method is used for the determination of the density or relativedensity of petroleum products as normally handled.

REF. 941960Effusiometer Schilling, complete with thermometer but without stand.

OPTIONAL ACCESSORY

SPARE PARTS

IP 59 Specific Gravity of Gases (Effusion Method)


941960 - SCHILLING EFFUSIOMETER

941961 Metallic stand

19010 Outer glass cylinder941965 Orif ice plate9419640 Inner glass cylinder w ith sealed outf it

15 Kgw 240 mmd 240 mmh 370 mm


See instrument under ASTM D2440

SCOPEThis test method indicates the tendency of a lubricating oil to deteriorate onoxidation under specified conditions.

IP 48 Oxidation Characteristics of Lubricating Oil


27241 - REDWOOD VISCOMETER


521341 Redw ood f lask 50 ml521367 IP thermometer 8C521369 IP thermometer 9C

69


SCOPEThis test method provides a measure of the viscosity by determining thetime of efflux of 50 ml of a cut-back bitumen, at 40°C, through a 10mmorifice.

OTHER STANDARDSNF T66005 - DIN 1995

REF.941826BRTA viscometer (4 unit) with electronic controller, electric stirrer, digitaldisplay, 4 receivers but without cup and valve.


IP 72 Viscosity of Cutback Bitumen


941826 - BRTA VISCOMETER (4 places)

11175 Graduated receiver

941830 Cup w ith orif ice 4 mm941831 Cup w ith orif ice 10 mm

941832 Ball valve 4 mm941833 Ball valve 10 mm

21375 Electronic stopw atch




941828 Cup w ith orif ice 2 mm

941834 Ball valve 2 mm

SCOPEThis test method determines the temperature below which a bitumen tendsto break rather than flow when stressed.


REF. 29250Breaking Point Apparatusthe apparatus consists of bending apparatus, plate made of springly stain-less 41x20x0,15 mm, cooling apparatus, IP 42C thermometer, plate andstand

ACCESSORIES

IP 80 Breaking Point of Bitumen (Fraas Method)


29250 - FRAAS APPARATUS

VA

Hz8 Kgw 350 mmd 270 mmh 420 mm

28754 Hot plate SB 16027555 Stainless steel plate (pack of 10)

29251 Set of glass tubes

70


SCOPEThis test method specifies a procedure for the determination of the heptaneinsoluble asphaltene content of gas oil, diesel fuel, fuel oils, lubricating oil,bitumen and crude petroleum which has been topped to an oil temperatureof 260°C.


REF. 10479Manual apparatus including extractor and condenser.


SPARE PARTS

REF. 24472ASPHAN 02 semi-automatic extractor for stand-alone precipitation, filtra-tion, washing, recycling, redissolution and evaporation processes ofasphaltene.

SPARE PARTS

IP 143 Asphaltenes in Crude Petroleum andPetroleum Products (Heptane Insolubles)


24472 - ASPHALTENE EXTRACTOR

14694 Evaporation cup15643 Filter paper - diameter 110 mm (pack of 100)23860 Hot plate (1500 W)

19364 Condenser

23883 500 ml conical f lask CN2423884 Ref lux extractor CN24/34

21918 500 ml conical f lask CN2921919 Ref lux extractor CN29/34

21364 500 ml low er boiler21365 1000 ml upper boiler w ith stopper21368 Condenser of the collector21369 500 ml solvent collecting f lask21372 Filter "Mitex" (box of 50)


21366 Double s urf ac e c ondens er21367 Cooler

71



SCOPEThis test method describes a method for the determination of gauge vaporpressures of liquefied petroleum gas products at temperatures within theapproximate range of 35 to 70°C.

IP 161 Gauge Vapor Pressure of LiquefiedPetroleum Gas Products

SCOPEThis test method covers the determination of the closed cup flash point ofpetroleum products and other liquids having flash point between -30 and70°C.

OTHER STANDARDSNFT 66009 - DIN 51755

REF. 941601Manual apparatus Abel model NAB 110, with electric heater and gas testjet.

OPTIONAL ACCESSORY

SPARE PARTS

REF. 41300Automatic Abel Tester model NAB 440 equipped with very large displayand printer, it is designed to operate from -30 to +110 °C and can be con-nected to a cryostat for test under 40°C. User-friendly software allows fullconfiguration and recording of 100 test results.


SPARE PARTS

IP 170 Flash Point by Abel Closed Cup Tester


41300 - AUTOMATIC ABEL NAB 440

41301 Abel cup41303 Abel cover41306 Stirrer f lexible41309 Detection cable41310 Pt 100 probe

23203 Cryostat TLC 30 - 5 liters (-30/+60°C ±.1)23204 Cryostat TLC 40 - 11 liters (-45/+20°C ±.05)

941143 Energy regulator

941604 Cup9416041 Lid shutter and stirrer w ith gas test jet


21227 IP thermometer 74C w ith collar21228 IP thermometer 75C w ith collar21229 IP thermometer 2C




941601 - MANUAL ABEL NAB 110

72


SCOPEThis test method covers procedures for evaluating the shear stability ofpolymer-containing oils in terms of the permanent viscosity loss resultingwhen a sample is mechanically stressed under the test conditions.


IP 294 Shear Stability of Polymer-Containing Oils(diesel Injector Rig Method)


SCOPEThis test method indicates the tendency of straight mineral oil to deteriorateon oxidation under specified conditions.

IP 306 Oxidation Stability of Straight Mineral Oil


SCOPEThis test method indicates the tendency of insulating oil to deteriorate onoxidation under specified conditions.

IP 307 Oxidation Stability of Mineral Insulating Oil


SCOPEThis test method specifies a method for the determination of the corrosivetendencies towards silver, of aviation turbine fuels.

IP 227 Silver Strip Corrosion of Aviation Turbine Fuel


SCOPEThis test method specifies a method for the determination of the resistanceto oxidation under specified conditions of unused inhibited mineral turbineoils.

IP 280 Oxidation Stability of Unused InhibitedMineral Turbine Oils

73



SCOPEThis test method covers the determination of the cold filter plugging point(CFPP) of diesel and domestic heating fuels using either manual or auto-mated test equipment.

IP 309 Cold Filter Plugging Point

See instrument underASTM D2440

SCOPEThis test method gives a measure of the tendency of new, inhibited, min-eral insulating oils to oxidize by measurement of an induction period.

IP 335 Oxidation Stability of Inhibited MineralInsulating Oils


SCOPEThis test method covers the automatic determination of the simulated filterplugging point (SFPP) of middle distillate fuels.

IP 419 Simulated Filter Plugging Point

74


SCOPEThis test method covers determination of the flash point at set temperaturein closed cup.


REF.942690GO/NO GO closed cup flash point tester. The model NPV 220 is designedfor paint, supple, japan, laque, solvent, cosmetic, perfume, distillate andvarious petroleum products.

REF.942691Identical to the previous unit but with heating slope. The model NPV 310 isdesigned for paint, supple, japan, laque, solvent, cosmetic, perfume, distil-late and various petroleum products.


OPTIONAL ACCESSORY

SPARE PARTS

ISO 3679 Closed Cup Flash Point at Set Temperature

942690 - FLASH POINT TESTER NPV 220


21604 Loading syringe (pack of 100)26075 Mercury thermometer for calibration purposes


41401 Detector lead NPV 22041403 Heating c artr idge 250W

942691 - FLASH POINT TESTER NPV 310





942695 Thermocouple NPV 310

75


SCOPEThis test method covers determination of traces of sulfur in petroleum distil-lates by the nickel reduction method.

REF.941489Complete equipment with heating mantle, glassware and energy regulator.

SPARE PARTS

UOP 357 Traces of Sulfur in Petroleum Distillatesby the Nickel Reduction Method

941489 - TRACE OF SULFUR TESTER


9414891 Heating mantle 100 ml (60 W)9414896 Nickel Reaney catalyst (100 g)

230 V10 A50 Hz23 Kgw 300 mmd 300 mmh 700 mm19018 Reaction f lask

19019 Funnel19020 Test tube

19017 Condenser19016 Inlet tube

19021 Outlet tube

EN 15323 Rotating Cylinder Ageing Test for Bitumen(RCAT method)

941878 - AGEING OVEN NRC 210



SCOPEThis test method is intended to measure the ageing effect of heat and air ona moving film of semi solid asphaltic material in the environment conditions.

REF.941878Double wall illuminated oven model NRC 210 with glass window deliveredcomplete and ready to use for RCAT test.

SPARE PARTS


941881 Solenoid valve941882 Rotating cylinder belt941883 Fan belt941884 Thermocouple sensor941885 Conical stopper941886 Straight stopper

941878 - ACCESSORIES


76


REFERENCE PRODUCTS WITH CERTIFICATE

PRODUCT REF. ASTM DESCRIPTION LEVEL VOLUME

GASOLINE 60018 D 4052 density at 15 °C 737 kg/m³ 250 ml60019 D 323 reid vapour pressure 64 kPa 250 ml60020 D 86 automatic distillation (unleaded) 33/186 °C 250 ml60021 D 2700 motor octane index (unleaded) 87.2 1000 ml60022 D 2699 research octane index (unleaded) 98 1000 ml60023 EN 238 benzene content 0.39 % vol 250 ml60029 ISO 20846 sulfur content 49 mg/kg 250 ml

DIESEL 60001 D 4052 density at 15 °C 836 kg/m³ 250 ml60010 D 4052 density at 15 °C 832 kg/m³ 250 ml60002 D 2500 cloud point -17 °C 250 ml60003 D 97 pour point -22 °C 250 ml60004 IP 309 cold filter plugging point -20 °C 250 ml60011 D 613 cetane index (measured) 52.2 1000 ml60005 D 86 automatic distillation 193/320 °C 250 ml60012 D 445 kinematic viscosity at 20 °C 3.572 cSt 250 ml60013 D 445 kinematic viscosity at 40 °C 2.356 cSt 250 ml60006 D 93 Pensky-Martens flash point 74.5 °C 250 ml60014 D 4294 sulfur content 296 mg/kg 50 ml60015 D 5453 sulfur content 48.5 mg/kg 50 ml60017 D 5463 sulfur content 4.7 mg/kg 50 ml

KEROZENE 60024 D 4052 density at 15 °C 799 kg/m³ 250 ml60025 D 2386 congeling point -48.9 °C 250 ml60026 D 445 kinematic viscosity at -20 °C 4.18 cSt 250 ml60027 D 1319 aromatics content 16.4 % 250 ml60028 D 611 aniline point 60.47 250 ml

LUBRICANT 60007 D 4052 density at 15 °C 880 kg/m³ 250 ml60008 D 92 Cleveland flash point 243 °C 250 ml60009 D 93 Pensky-Martens flash point 213 °C 250 ml

CALIBRATION INSTRUMENT WITH CERTIFICATION

REF. 41200Calibration instrument for the WHOLE range of automated NORMALABANALIS apparatus models 430 and 440. This instrument is dedicated for temperatures and pressures measurementsand it is equipped with a 24-keys keyboard, LCD display, RS232C output.It is delivered with official COFRAC calibration certificate.

41200 - CALIBRATION INSTRUMENT


77


ASTM E 1 Thermometers

ASTM ref. range grad depthn° °C °C mm

1C 11489 -20/+150 1 762C 11490 -5/+300 1 763C 11491 -5/+400 1 765C 11492 -38/+50 1 1086C 11493 -80/+20 1 767C 11494 -2/+300 1 total8C 11495 -2/+400 1 total9C 11496 -7/+110 0.5 5710C 11497 +90/+370 2 5711C 11498 -6/+400 2 2512C 11499 -20/+102 0.2 total13C 11500 +155/+170 0.5 total14C 11501 +38/+82 0.1 7915C 11502 -2/+80 0.2 total16C 11503 +30/+200 0.5 total17C 11504 +19/+27 0.1 total18C 11505 +34/+42 0.1 total19C 11506 +49/+57 0.1 total20C 11507 +57/+65 0.1 total21C 11508 +79/+87 0.1 total22C 11509 +95/+103 0.1 total23C 11510 +18/+28 0.2 9024C 11511 +39/+54 0.2 9025C 11512 +95/+105 0.2 9026C 11513 +130/+140 0.1 total27C 11514 +147/+182 0.5 7633C 11515 -38/+42 0.2 5034C 11516 +25/+105 0.2 5035C 11517 +90/+170 0.2 5136C 11518 -2/+68 0.2 4537C 11519 -2/+52 0.2 10038C 11520 +24/+78 0.2 10039C 11521 +48/+102 0.2 10040C 11522 +72/+126 0.2 10041C 11523 +98/+152 0.2 10042C 11524 +95/+255 0.5 10044C 15629 +18.5/+21.5 0.05 total45C 15630 +23.6/+26.1 0.05 total46C 15631 +48.6/+51.4 0.05 total47C 15632 +58.6/+61.5 0.05 total49C 11525 +20/+70 0.2 6552C 11526 -10/+5 0.1 total54C 20218 +20/+100 0.2 total56C 11528 +19/+35 0.02 total57C 11529 -20/+50 0.5 5761C 11530 +32/+127 0.2 7962C 11531 -38/+2 0.1 total63C 11532 -8/+32 0.1 total64C 11533 +25/+55 0.1 total65C 11534 +50/+80 0.1 total66C 11535 +75/+105 0.1 total67C 11536 +95/+155 0.2 total68C 11537 +145/+205 0.2 total69C 11538 +195/+305 0.5 total70C 11539 +295/+405 0.5 total71C 20219 -37/+21 0.5 76

See overleaf

ASTM ref. range grad depthn° °C °C mm

82C 11540 -15/+105 1 3083C 11541 +15/+70 1 4084C 11542 +25/+80 1 24985C 11543 +40/+150 1 18186C 11544 +95/+175 1 3587C 11545 +150/+205 1 4088C 11546 +10/+200 1 5789C 11547 -20/+10 0.1 7690C 11548 0/+30 0.1 7691C 11549 +20/+50 0.1 7692C 11550 +40/+70 0.1 7693C 11551 +60/+90 0.1 7694C 11552 +80/+110 0.1 7695C 11553 +100/+130 0.1 7696C 11554 +130/+150 0.1 7699C 15164 -40/+4 0.2 35100C 11555 +145/+205 0.2 76101C 11556 +195/+305 0.5 76102C 11557 +123/+177 0.2 100103C 11558 +148/+202 0.2 100104C 11559 +173/+227 0.2 100105C 11560 +198/+252 0.2 100106C 11561 +223/+277 0.2 100107C 11562 +248/+302 0.2 100110C 15634 +133.6/+136.4 0.05 total111C 11563 +170/+250 0.2 100112C 11564 +4/+6 0.02 total113C 11565 -1/+20 0.5 total114C 11566 -80/+20 0.5 total116C 20220 +18.9/+25.1 0.01 total117C 20221 +23.9/+30.1 0.01 total118C 15635 +28.6/+31.4 0.05 total119C 20222 -38.3/-30 0.1 100120C 10025 +38.5/+41.5 0.05 total121C 10026 +98.5/+101.5 0.05 total122C 29020 -45/-35 0.1 total123C 29021 -35/-25 0.1 total124C 29022 -25/-15 0.1 total125C 29023 -15/-5 0.1 total127C 22082 -21.4/-18.6 0.05 total

15165 Sleeve for ASTM 99C thermometer

THERMOMETERS IN °F : ON REQUEST

78


IP Thermometers

IP ref. range grad depthn° °C °C mm

2C 21229 -80/+20 1 1083C 21049 -1/+105 0.5 total8C 521367 0/+45 0.2 659C 521369 +40/+85 0.2 6515C 25960 -5/+110 0.5 5718C 21826 +20/+100.6 0.2 total22C 25961 +195/+205 0.1 10030C 21651 +23.6/+26.4 0.05 total39C 21675 -1/+38 0.1 total42C 11337 -38/+30 0.5 25044C 21915 +15/+30 0.2 2271C 21650 -27.4/-24.6 0.05 total81C 25959 +98/+152 0.2 10091C 23184 0/+110 1 4498C 23185 +100/+300 2 44

Special with collar74C 9921227 -35/+70 0.5 6175C 9921228 -30/+80 0.5 89

THERMOMETERS IN °F : ON REQUEST

Miscellaneous Thermometers

Ref. Description

9410759 Thermometer for grease worker23190 Thermometer with certificate +40/+260°C9419124 Thermometer ISO 65315287 Thermometer AFNOR -15/+45°C15288 Thermometer AFNOR +35/+85°C15351 Thermometer 75F for ASTM D1177 -35/+35°F15352 Thermometer 76F for ASTM D1177 -65/+5°F26075 Mercury thermometer for calibration27251 Engler with ring +10/+55°C in 0.5°C27252 Engler with ring +10/+110°C in 1°C60135 Modified thermometer 120C for NVH 45060136 Modified thermometer 121C for NVH 450

79


STANDARD REF. MODEL DESCRIPTION PAGE

ASTM D113 9418641 P 864 Ductility meter (100 cm) 13

ASTM D113 9418642 P 864A Ductility meter (150 cm) 13

ASTM D1142 941975 P 975 Dew-point tester 3 to 15 psi 38

ASTM D1142 9419751 P 975A Dew-point tester 0 to 350 psi 38

ASTM D1160 9411280 P 1280 Distillation at reduced pressure (1 to 50 mmHg) 38

ASTM D1177 9411520 P 1520 Freezing point 39

ASTM D1265 941501 Stainless steel sampling vessel (500 cc) 40



ASTM D1265 9414541 Stainless steel sampling vessel (1gallon) 40

ASTM D1266 941454 P 454 Sulphur determination in petroleum (6-unit) 41

ASTM D1267 941432 P 432 Vapour pressure of LPG 42

ASTM D1319 941600 Adsorption apparatus 4 places 43

ASTM D1322 941680 P 680 Smoke point apparatus 44

ASTM D1401 941545 P 545 Semi-auto tester for demulsibility of oils 44

ASTM D1401 941550 P 550 Automated demulsibility tester 44

ASTM D1500 24415 Colorimeter with colour disc 46

ASTM D1552 941450 P 450 Tube furnace for sulphur determination 46

ASTM D156 941520 P 520L Saybolt chromometer 15

ASTM D156 941521 Saybolt chromometer for waxes 15

ASTM D1655 27235 Engler vicometer 47

ASTM D1657 941911 P 911 Tester for specific gravity of LPG 47

ASTM D1657 9419110 Same apparatus with burst disc 47

ASTM D1742 941778 P 778 Oil separation from grease during storage 48

ASTM D1754 941876 P 876 Effect of heat and air on asphaltic material 49

ASTM D1831 941744 P 744-2B Roll stability Tester 49

ASTM D1837 941940 P 940 Tester for Volatility of LPG 50

ASTM D1838 941432 P 432 Copper strip corrosion by LPG 50

ASTM D189 941653 P 653 Conradson carbon residue apparatus 16

ASTM D2001 19398 Depentanization apparatus 50

ASTM D2002 19399 Complete absorption column (method B) 51

ASTM D2003 19400 High efficiency column 51

ASTM D2068 41800 NBF 241 Automatic FBT tester 51

ASTM D2068 41801 NBF 240 Complete bench top model with printer 51

ASTM D2112 9416298 P 629H Oil thermostatic bath for 2 vessels 52

ASTM D2158 941957 P 957 Tester for determination of extraenous materials 52

ASTM D2386 941556 P 556 Complete freezing point apparatus 54

ASTM D2420 941958 P 958 Hydrogen sulfide in liquefied petroleum gases 55

ASTM D2440 941650 P 650 Oxidation tester for lubricating oils (12 test) 55

ASTM D2619 941995 P 995 Tester for hydrolytic stability of fluids 57

ASTM D2624 23628 P 981 Portable Conductivity meter 57

ASTM D2784 24516 Wickbold Tester for sulphur content 59

ASTM D287 14854 6-unit ramp in stainless steel 17

ASTM D2872 941877 P 877 Complete RFTOT oven 59

ASTM D323 941432 P 432 Constant temperature water bath (3 test) 18

ASTM D3230 941287 P 287 Salt in crude oil tester 60

ASTM D3427 941688 P 688 Impinger test rig 61

ASTM D36 40100 NBA 440 Automatic softening point tester (NBA 440) 4

ASTM D36 20761 Ring and ball apparatus (shouldered ring) 4

ASTM D381 941302 P 302 Air jet apparatus for determination of gums 19

ASTM D381 941303 P 303 Air/steam jet apparatus for determination of gums 19

ASTM D4057 22213 Brass weighted bottle (neck 19mm) 63

ASTM D4057 22214 Brass weighted bottle (neck 38mm) 63

ASTM D4057 519032 Sampling thief (vessel type) 63

ASTM D445 60100 NVH 450 Houillon Vicometer 20

80


STANDARD REF. MODEL DESCRIPTION UK PAGE

ASTM D445 18450 Automatic washer for viscometer 21

ASTM D445 17915 Kinematic viscosity bath “Routine” (20 liters) 21

ASTM D445 23829 Kinematic viscosity bath “Routine” (20 liters) 21

ASTM D445 941131 P 131 Kinematic viscosity bath “Precision” (8 visco,) 21

ASTM D4530 41023 NMC 440 Automatic micro carbon residue tester 64

ASTM D4530 941670 NMC 210 Automatic micro conradson 64

ASTM D473 941281 P 281 Extraction apparatus complete 26

ASTM D482 23963 Muffle furnace for ash determination 27

ASTM D5 27794 Constant temperature water bath (max 100°C) 2

ASTM D5 941731 P 731 Manual penetrometer 2

ASTM D5 941734 P 734 Automatic penetrometer 2

ASTM D5 9417582 P 758-2 Automatic grease working machine (twin unit) 2

ASTM D524 941671 P 671 Ramsbottom carbon residue tester (5 test) 27

ASTM D525 40900 Automatic 2-unit tester with liquid bath 28

ASTM D525 40925 Automatic 4-unit tester with metallic bath (NPI 911) 28

ASTM D525 941372 P 372 4-place water bath 28

ASTM D56 40600 NTA 440 Automatic TAG flash point tester 5

ASTM D5800 941783 P 783 Noack tester with glassware 66

ASTM D6 941875 P 875 Loss on heating 3

ASTM D6082 9416432 Foam test bath at 150°C 34

ASTM D611 41100 NPA 410 Automatic aniline point tester 29

ASTM D611 40500 NAE 440 Automatic aniline point tester 29

ASTM D613 52000 Cetane blender 2 tanks 30

ASTM D613 52100 Octane blender 3 tanks 30

ASTM D613 52200 Cetane + octane blender (2 cetane + 3 octane) 30

ASTM D613 52300 Cetane + octane blender (2 cetane + 4 octane) 30

ASTM D6371 20878 Manual cold filter plugging point tester 67

ASTM D6371 51052 NTL 452 Automatic cold filter plugging point 67

ASTM D664 941708 P 708 Neutralisation number apparatus 31

ASTM D665 9416306 P 630 Rust-preventing characteristics (6 unit) 31

ASTM D70 24615 Thermostatic bath 5

ASTM D721 941795 P 795 Oil content of petroleum waxes 32

ASTM D86 40000 NDI 440 Automatic D86 distillation unit 7

ASTM D86 941227 P 227 Distillation “Front view” (receiver on left) 6

ASTM D86 941228 P 228 Distillation “Front view” (receiver on right) 6

ASTM D86 942228 NDI 210 Semi-automatic Distillation (receiver on right) 6

ASTM D877 23797 Analyseur for dielectric breakdown voltage 33

ASTM D877 27196 Portable tester for routine analysis 33

ASTM D88 27238 Saybolt Viscometer 8

ASTM D892 941640 P 640 Foaming test apparatus (1 bath) 34

ASTM D892 941643 P 643 Foaming test apparatus (2 bath) 34

ASTM D892 9416431 Automatic time sequencer 34

ASTM D91 29038 Centrifuge with rotor (without heating) 8

ASTM D91 29039 Centrifuge with rotor (with heating 60°C) 8

ASTM D92 40400 NCL 440 Automatic cleveland flash point tester 9

ASTM D92 942611 NCL 120 Manual cleveland open cup tester 9

ASTM D92 942610 NCL 220 Semi-automatic Cleveland flash point tester 9

ASTM D93 40300 NPM 440 Automatic P-M flash point tester 11

ASTM D93 942614/15 NPM 120 Manual P-M flash point tester 10

ASTM D93 942616 NPM 121 Manual P-M flash point tester 10

ASTM D93 942617/18 NPM 220 Semi-automatic P-M flash point tester 10

ASTM D93 942619 NPM 221 Semi-automatic P-M flash point tester 10

ASTM D942 941769 P 796 2-place bath without accessory 35

ASTM D942 941770 P 770 4-place bath without accessory 35

ASTM D943 9416260 Tester for oxidation stability test (no flowmeter) 36

81


STANDARD REF. MODEL DESCRIPTION UK PAGE

ASTM D95 21454 Complete apparatus with electric heater 11

ASTM D97 941584 P 584 Manual cloud and pour point apparatus (5-unit) 12

ASTM D97 941592 P 592 Manual cloud and pour test cabinet (4 test) 12

ASTM D97 941595 P 595 Manual cloud and pour test cabinet 1 post -69°C 12

ASTM D972 941771 P 771 Evaporation cell for grease 37

ASTM D972 941772 P 772 Evaporation cell for oil 37

IP 143 10479 Complete glassware (manual version) 70

IP 143 24472 Semi-automatic Asphan 02 extractor 70

IP 170 41300 NAB 440 Automatic Abel flash point 71

IP 170 941601 NAB 110 Manual Abel Flash Point Tester 71

IP 59 941960 P 960 Schilling effusiometer 68

IP 70 27241 Redwood viscometer 68

IP 72 941826 P 826 BRTA viscometer (4-unit) 69

IP 80 29250 Fraas apparatus 69

ISO 3679 942690 NPV 220 Closed cup flash point tester 74

ISO 3679 942691 NPV 310 Closed cup flash point tester 74

UOP 357 941489 P 489 Trace of sulfur tester 75

EN 15323 941878 NRC 210 RCAT 75

CAL 41200 Calibration apparatus 76

THE INTERNATIONAL CATALOG · See other applications under ASTM D 850 - D 1078 SCOPE This test...

Documents

Transcript of THE INTERNATIONAL CATALOG · See other applications under ASTM D 850 - D 1078 SCOPE This test...