Thank you for your purchase of a NAUTICAM camera...
Transcript of Thank you for your purchase of a NAUTICAM camera...
0
1
Thank you for your purchase of a NAUTICAM camera housing.
At NAUTICAM, we pride ourselves on the ability to recognise the
requirements of professional as well as amateur underwater
photographers and fulfill them through the innovative designs of our
products. We strive to achieve a high level of user-friendliness by
allowing stress-free installation and easy operation of all important
functions of the camera.
Each housing is individually inspected and water pressure tested to
ensure optimum quality.
Please read this manual carefully before using the housing, this will
maximise its performance as well as its lifetime.
2
1. All NAUTICAM Products are warranted against any material and
manufacturing defects for one year from the date of purchase for
consumer use.
2. NAUTICAM accepts no liability for any damage to and defects in the
housing caused by improper use and/or poor maintenance; it is the
responsibility of the owner to carefully follow the instructions in
this manual.
3. NAUTICAM does not hold responsibility for damage, of any nature,
to any equipment used with and/or placed within the housing.
4. NAUTICAM accepts no liability for any loss of captured images or
the inability to capture images even if it is due to the
malfunctioning or leakage of the housing.
5. This warranty only applies to products purchased from authorised
NAUTICAM dealers and does not extend beyond the original retail
purchaser.
6. Unauthorised modifications and/or repairs of the housing will
automatically invalidate this warranty.
7. To return products for service, please contact our regional
distributor, normally you would need to notify them by email first
and ship them the product by registered mail, along with your
contact details and a brief description of the defect.
3
1. NA-A6000 housing
2. Instruction manual
3. Spare silicone rubber housing o-ring
4. O-ring remover
5. CR2450 battery (for moisture alarm)
6. Lubricant
7. Set of Allen keys
Spare silicone rubber o-ring
Lubricant Set of Allen keys
CR2450 battery O-ring remover
4
1. A water-tight test without the camera inside the housing is highly
recommended when using the system for the first time and after
the changing of port and O-ring(s).
2. Do not use lubricants from other brands with the silicone rubber O-
ring on this housing, only use the lubricant provided by NAUTICAM.
3. Discontinue use immediately should you notice any leakage.
4. Store the housing in a robust, shock-proof container during
transportation; avoid transporting with any equipment, such as a
camera, inside the housing.
5. When travelling by air, do not close the housing if the port is
installed, as this may lead to a pressure difference between the
atmosphere and inside the housing.
6. Care must be taken when opening the housing, as pressure may
build up inside the housing which increases the opening force.
7. Do not open the product in a wet or sandy environment. Protect
the interior from moisture and debris in order to prevent
malfunction or leakage.
8. Do not store the product in an environment of high humidity.
9. Do not leave the housing and the camera in direct sunlight for
prolonged periods.
10. Keep out of reach of children, failure to do so could result in injury.
11. Defective products should be shipped to our distributors for service,
unauthorized disassembling and/or modifications could result in
malfunction or leakage.
5
Specifications 6
Identification of Parts 7
Preparation of the Housing 10
Opening and Locking the Housing 13
Installing the Camera 14
Mounting the Port 15
Care and Maintenance 17
Optional Accessories 18
6
Construction
Housing body: Aluminium alloy
Surface treatment: Hard anodised
Display window: Abrasion resistant polycarbonate
Dimensions
Width: 192mm
Height: 124mm
Depth: 93mm
Weight Approx. 1.01kg (without camera)
Buoyancy Slightly negative
Depth rating 100 metres
Features
Moisture alarm: Blinking LED and audible alarm
TTL capability:
Optical fibre mount included for external strobes connection, utilising the camera’s pop-up flash as trigger.
Port mount: Patented easy port installation system.
Control dial: Easily reached by thumb.
EVF/LCD switch: Switch between EVF and LCD with the flick of a switch.
7
1 Flash up/off lever 6 Housing lock safety button
2 Mode dial 7 Housing lock
3 Control dial 8 M10 strobe mounting base
4 C1 button 9 ON/OFF switch
5 Shutter release lever 10 Lens release button
1
2
3
4
8
7
5
9
10
6
8
11 Accessory coldshoe 15 Zoom/Focus knob
12 Optical fibre mount 16 Port release safety button
13 Port alignment index 17 Port lock/release lever
14 M16 accessory port 18 1/4”–20UNC tripod socket x 2*
11
18
14
* The maximum length of screws that can be used with the tripod sockets is 4mm
12
13
15
16
17
9
19 Viewfinder/LCD lever 26 Up selection/Display button
20 Moisture alarm window 27 Right selection/ISO button
21 Menu button 28 Set button
22 AEL button 29 Left selection/Drive mode button
23 Movie button 30 Down selection/Exposure comp./Image index button
24 Fn button 31 C2/Delete button
25 Control wheel 32 Playback button
19
21
22
23
25
20
24
26
28
27
29
32
30
31
10
1. After verifying that the housing O-ring is in good condition, lightly
coat it with the lubricant provided.
2. Make sure the O-ring groove located in the rear part of the housing
is free from any foreign material; the groove can be cleaned with
the aid of a microfiber cloth.
3. Place the O-ring into the groove.
4. To install the optical fibre mount for external strobe connection,
fasten it with the screws provided to the threaded sockets of the
accessory coldshoe as shown:
11
1. Install the CR2450 battery provided
into the battery compartment inside
the rear housing.
To remove the battery, use a small
flat-head screwdriver to lift up the
battery as shown.
5. Setting up the moisture alarm:
3. Test the alarm by contacting the two
wires near the bottom of the
housing with a damped cotton bud;
the alarm should start giving out a
repeating “beep” sound along with
a flashing red light. The “beep”
sound and the light should keep on
going for 5 seconds after the
removal of the damped cotton bud.
2. Switch the alarm on. The LED light
will turn blue for five seconds
indicating the battery is normal.
Then it goes into flashing blue light
standby mode.
12
LED status identification:
On start up:
LED indicator Status
Steady "Blue" light Battery is normal, goes into flashing "Blue" light
standby mode after 5 seconds.
"Blue" and "Red"
lights alternating
Battery low. Replace battery as soon as possible.
Goes into standby mode after 5 seconds.
Steady "Red" light Battery empty, replace battery.
After start up:
LED indicator Status
Flashing "Blue"
light
Standby mode. The moisture alarm is active, and
the system is ready for vacuum indication
whenever a vacuum is detected.
Flashing "Red" light
with audio sounds.
Moisture is detected.
Flashing "Yellow"
light
Some vacuum is detected, target vacuum level is
not reached.
Steady "Green"
light
Target vacuum level is reached.
Rapidly flash
"Yellow" light
Vacuum is dropping. (Will occur only after target
vacuum level is reached)
Rapidly flashing
"Red" light
Vacuum is totally lost. Circuit stalled until switched
off. (Will occur only after target vacuum level is
reached)
(Optional) Vacuum valve can be
attached to the housing via one
of the accessory port for
conducting a vacuum seal test.
Please refer to the manual of the
vacuum valve for more details of
the operation.
13
To open the housing:
To lock the housing:
2. Turn the housing lock anti-
clockwise for 270°, until the lock
reaches the “Open” position as
shown.
3. Close the housing while the
housing lock is in the “Open”
position.
4. Turn the housing lock clockwise
for 270°, until the lock reaches the
“lock” position as shown.
Confirm that the white indicator
line on the safety button is visible.
1. Press the housing lock safety
button.
14
1. Disengage the red camera saddle
locks by pressing them inwards.
Remove the camera saddle from
the housing by sliding it outwards.
2. Tilt the LCD monitor of the camera
upwards, then attach the saddle to
the camera by tightening the screw
to the tripod socket of the camera.
3. Install the camera by sliding
the attached saddle along the
rail in the housing until it
cannot go in any further.
4. Please make sure the eyepiece
cup is not attached to the
camera. Confirm that the red
camera saddle locks are in the
engaged position before closing
the housing.
15
Please refer to the NAUTICAM system port chart for a range of compatible
ports.
1. Remove the O-ring from the
port, inspect for any damage
and lightly coat it with the
provided lubricant before
placing it back into its groove.
2. Verify that the port opening of
the housing is clean and free
from foreign material.
3. Push the safety button of the port
locking lever downwards.
4. Turn the port locking lever to the
release position as shown.
5. Lift housing cap.
16
6. Align the Port mounting indices of
the port and the housing.
7. Gently push the port into the port
opening of the housing, until it
cannot go in any further.
8. Lock the port into place by turning
the port locking lever to the inward
position. To ensure that the port is
securely mounted, confirm that the
green line on the safety button of
the port locking lever is visible.
9. To remove the port from the
housing, simply turn the port locking
lever to the outward position and
gently pull it out.
17
1. Soak the housing system in fresh water after each salt water use,
during which all control buttons/knobs should be operated a few
times to avoid the accumulation of salt residue; wipe the housing
with a towel before opening.
2. After each day of diving, it is advisable to have the main O-ring in
the rear part of the housing removed from its groove with the O-
ring remover and inspected for damage. Also check that the O-ring
retains its original circular shape; never stretch the O-ring
excessively or remove it with a sharp object. The O-ring groove
should be cleaned to ensure it is free from any salt deposit or
foreign material; lightly coat the O-ring with the provided lubricant
before reinstalling it in the groove. A damaged O-ring should be
discarded immediately and replaced only with one that is provided
by NAUTICAM.
3. Replace the main O-ring annually.
4. It is recommended that you ship the housing to our distributor for a
complete overhaul every year or after every 200 dives.
18
P.N. 17454
NA-A6000 LCD window for Nauticam enhanced viewfinders
P.N. 25612
M16 Vacuum Valve
19