ESTD 1960

Opp. Kala Kendra, Bikram Chowk, Jammu, J&K-180004 Website:- www.govtpolytechnicjammu.edu.in

email:- govtpolyjammu@gmail.com

Fax:-0191-2435373 Ph. 0191-2457891

NIT NO: 04 of 2015

TENDER DOCUMENT NO:- GPJ/F-678/1576-78

DATED:- 30.12.2015

“TENDER DOCUMENT FOR SUPPLY OF RAW MATERIAL/

TOOLS FOR VARIOUS GOVT. POLYTECHNICS OF

JAMMU DIVISION”

TENDER FORM

NIT No:- 04 of 2015 TENDER DOCUMENT NO:- GPJ/ F-678/1576-78

DATED:-30.12.2015

To

The Principal Government Polytechnic Bikram Chowk, Jammu

Sir/Madam,

I ______________________________________________________________

from M/S______________________________ hereby submit the tender for the supply

of following items for _____________________________ departments as per the detail

attached herewith. I further affirm that I have read and fully understood the tender notice

and agree to abide by all the terms and conditions laid therein, which are signed as a

token of acceptance. The undersigned hereby offers to execute supply of items as per

specification against which I have quoted the rates and for which this tender may be

accepted at the rates stated there in and subject to the terms & conditions set forth for

such items as may be ordered by various Principals of Govt. Polytechnics of Jammu

Division.

Yours Faithfully,

Signature____________________________________________________________________

Date________________________________________________________________________

Name of the Tenderer _________________________________________________________

Amount of CDR with Bank name and Date:__________________________________________

M/S ________________________________________________________________________

Phone __________________________ Mobile ______________________________________

Fax ____________________________

Fax:-0191-2435373 Ph.:-0191-2457891

Er. Ritu Jamwal Principal

ESTD: 1960

GOVERNMENT OF JAMMU AND KASHMIR GOVERNMENT POLYTECHNIC JAMMU

Opp. Kala Kendra, Bikram Chowk, Jammu Website:- www.govtpolytechnicjammu.edu.in

Email:- govtpolyjammu@gmail.com

NOTICE INVITING TENDER NIT No:- 04 of 2015 Dated:- 30/12/2015

For and on behalf of the Governor of Jammu and Kashmir State sealed tenders affixed with Rs 5/- revenue stamps are invited from Registered dealers/Authorized suppliers/ Authorized Dealers of manufacturers for the supply of Raw material/Tools for various Govt. Polytechnics of Jammu division (Jammu, Samba, Kathua, Reasi, Udhampur, Poonch, Doda, Ramban, Kishtwar) as per list enclosed in tender document. The tender should be accompanied with the earnest money in the form of CDR/FDR pledged to the Principal Government Polytechnic, Bikram Chowk Jammu of any scheduled bank without which tender will be out rightly rejected as per the following detail:-

S. No. Name of Tender Earnest money (in Rupees)

Cost of Tender documents (in Rupees)

1. Tender for Computer/ Electrical/Electronics (Raw material)

Rs.5000/- Rs.200/-

2. Tender for General Workshop/Mechanical/ Automobile Engg (Raw material)

Rs.5000/- Rs.200/-

3. Tender for Physics/Chemistry /Medical Lab Technology/Stationery (Raw material)

Rs.5000/- Rs.200/-

The tender document containing list of raw material required and Terms & conditions can be had from the office of the undersigned against the cost mentioned above on any working day after the publication of this notice in newspaper upto 4:00 PM. The complete sealed tender document with quoted rates at specified place in the document along with the earnest money for an amount shown above against each tender in the form of CDR/FDR should reach the office of the Principal Government Polytechnic, Jammu by hand/Registered post on or before 20-01-2016 upto 4:00 PM. In case that the last day of receipt happens to be a non working day, next working day shall be considered as the last day of receipt of the tender documents. The tender will be opened on 21-01-2016 at Govt. Polytechnic, Bikram Chowk Jammu at 12:00 Noon in presence of the tenderers who may like to be present on opening date. The undersigned shall have the authority to accept or reject any or all tenders without assigning any reasons thereof. The tender document shall be available on official website of this institute www.govtpolytechnicjammu.edu.in and on www.jkdte.org of Directorate of Technical Education, J&K.

No: GPJ/F-678/1576-78 Dated: 30/12/2015 (Er. Ritu Jamwal)

(Chairman D.L.P.C) Principal, Govt. Polytechnic, Jammu

Copy to: 1. The Director, Technical Education, J&K, Jammu/Srinagar for information. 2. The Joint Director, Information Department Jammu with the request to kindly get the notice widely

publicized in at least three leading Local English/Hindi News Paper preferably in Daily Excelsior, State Times, Greater Kashmir, Danik Jagran etc for minimum three days.

3. The General Manager, Govt. Press Jammu for publication in the coming issue of the Govt. Gazette. 4. Tender File.

Detailed tender Notice/terms and conditions for supply of RAW MATERIAL for various Govt. Polytechnics of Jammu Division (2015-16)

For and on behalf of the Governor of Jammu and Kashmir State sealed tenders affixed with Rs 5/- revenue stamps are invited from Registered dealers/Authorized suppliers/ Authorized Dealers of manufacturers for the supply of Raw material for various departments of Govt. Polytechnics of Jammu division as per list enclosed in tender document. The tender should be accompanied with the earnest money in the form of CDR/FDR pledged to the Principal Government Polytechnic, Jammu of any scheduled bank without which tender will be out-rightly rejected as per the following detail and should reach office of the undersigned by or before 20-01-2016 upto 4:00 PM.

S. No. Name of Tender Earnest money (in Rupees)

Cost of Tender documents (in Rupees)

1. Tender for Electrical/Computer/Electronics (Raw material)

Rs.5000/- Rs.200/-

2. Tender for General Workshop/Mechanical/ Automobile Engg (Raw material)

Rs.5000/- Rs.200/-

3. Tender for Physics/Chemistry /Medical Lab Technology/Stationery (Raw material)

Rs.5000/- Rs.200/-

TERMS AND CONDITIONS:-

1. Tender must be enclosed in a properly sealed envelope and addressed to the Principal, Govt. Polytechnic, Bikram Chowk, Jammu indicating the department for which tender is applied.

2. The single rate should be quoted F.O.R Govt. Polytechnics of Jammu Division i.e Jammu, Kathua, Samba, Reasi, Udhampur, Poonch, Ramban, Doda and Kishtwar inclusive of taxes (VAT, Entry Tax etc.)/ All charges/ Freights, Insurance, forwarding and incidental charges, if any wherever applicable.

3. Each tender must be accompanied with a CDR/FDR as indicated in the abbreviated tender notice, pledged in favour of the Principal, Govt. Polytechnic, Jammu without which the tender will not be entertained /accepted Cheque/Demand Draft instead of CDR/FDR will be rejected straight away without any notice. The Tenderers who may download the tender documents from the website should submit the postal order or Demand draft as cost of each tender document along with the tender failing which the tender will be rejected.

4. The successful tenderer shall have to make the supplies of the ordered quality, specification, make, mark, size etc. within 30 days from the date of the supply order. The payment will be made by the respective college only after receipt and verification of the items. Goods other than the approved quality and specification will not be accepted.

5. Tenderers should quote the rates without any erasing, overwriting, cutting etc. Mutilated tenders shall not be accepted/ entertained.

6. The rates should be quoted only on the tendered items on the prescribed tender document obtained from the office/downloaded from website. The rates quoted on other than the tender document will not be accepted and the tender will be rejected.

7. Tenders received after the prescribed date and time will not be entertained. Any tender received after the date though posted in time but delayed during transit due to postal delay or otherwise will not be entertained and shall be returned to the addressee. However, in case the last date happens to be Strike or holiday then the next working day will be treated as last date for receipt of these tenders.

8. The tenders should be accompanied with relevant literature wherever required. The make and model should be mentioned with the items for which the rates have been quoted.

9. In case the successful tenderers fails to supply the goods of the prescribed specifications, make, mark, quality etc. within the stipulated time period, the CDR of such firm/tenderer will be forfeited in favour of the Govt. and the department shall be at liberty to arrange the supplies through re-tender or otherwise.

10. In case any dispute/doubt/deference/question arise between the tenderer and the department regarding interpretation of any of the terms and conditions or any other matter relating to the purchase, the same shall be referred to the Director Technical Education (J&K Govt.) or any other officer nominated by him in this behalf for arbitration, whose decision in the matter shall be final, conclusive and binding upon the parties. All the disputes between the parties involving legal intervention shall be subject to the jurisdiction of J&K High Court.

11. The rates shall remain valid upto one year from the date of finalization of rate contract. 12. The intending tenderers should provide latest Income Tax returns, VAT clearance Certificate up

to 31-03-2015 and Registration certificate. 13. The tenderer should clearly mention warranty/guarantee period of the product. 14. The quantity mentioned in the tender document may increase or decrease as per the availability

of funds and other related variations. 15. The tenderer shall have to provide training to the identified officials of the department to

operate the machinery at the place of installation wherever necessary. 16. In case of specification, the committee shall have the right to take decision in consultation with

experts at the time of the finalization of rates. 17. The small scale industries units of the state who desire to quote the rates will be dealt in

accordance with State Industrial Policy. 18. In case rates of any items are available on DGS&D rate contract or on any Govt. approved rate

contract at the time of approval, the cases will be decided accordingly. 19. The Principal, Govt. Polytechnic, Jammu reserves the right to accept or reject any tender or all

the tenders or part thereof without assigning any reason thereof.

(Er. Ritu Jamwal) (Chairman, D.L.P.C) Principal

Govt. Polytechnic Jammu

Fax:-0191-2435373 Ph. 0191-2457891

Er. Ritu Jamwal Principal

ESTD: 1960

GOVERNMENT OF JAMMU AND KASHMIR

GOVERNMENT POLYTECHNIC JAMMU

Opp. Kala Kendra, Bikram Chowk, Jammu Website:- www.govtpolytechnicjammu.edu.in

Email:- govtpolyjammu@gmail.com

Items required for General Workshop/ Mechanical/ Automobile Engg.

Department

Note:- Rate to be quoted FOR Govt. Polytechnics of Jammu Division i.e Jammu, Samba, Udhampur inclusive of taxes (VAT, Entry Tax etc.) / All charges/ Freights, Insurance, forwarding and incidental charges

GENERAL WORKSHOP

S.NO NAME OF EQUIPMENT SPECIFICATIONS TENTATIVE QTY PRICES PER UNIT INCLUSIVE OF TAXES

1. Crosscut Saw with handle (JK/Eastman/Taparia/Pye)

Blade length: 450mm(Approx)

Blade Material: High quality Steel with hardness approx.=RC52

Handle: wooden or high quality plastic

05

2. Adjustable Hacksaw with Blade(JK/Eastman/Taparia/Pye)

Blade Size: 8”-12”

Frame/Handle: Soft PVC/Wood

05

3. Iron Jack Plane with wooden handle(JK/Eastman/Taparia/Pye)

Cut Iron: High carbon steel

Body: Cast Iron

Size: 8",14",18"

05 each

4. Rebate Plane adjustable blade type(JK/Eastman/Taparia/Pye)

Cutter material: High carbon steel

Blade Size:1/2", 3/4",1"

05 each

5. Iron/Wooden smoothening Plane(JK/Eastman/Taparia/Pye)

Cutter material: High carbon steel

Size: 9", Blade Size :50 mm(Approx)

10

6. Claw Hammer(JK/Eastman/Taparia/Pye)

Head: Forged high carbon steel

Handle: hard wood and polished/lacquer coated or Cushioned Plastic

Weight Approx.: 250 gms. &450 gms.

05 each

7. Wooden Mallet with handle(JK/Eastman/Taparia/Pye)

Weight: 300gms, 500gms & 800gms (Approx).

05 each

8.

Ball peen Hammer Head: Forged high carbon steel

Handle: hard wood and polished/lacquer coated or Cushioned Plastic

weight Approx. : 250 gms.,450 gms.

05 each

9.

Cross peen Hammer Head: Forged high carbon steel

Handle: hard wood and polished/lacquer coated or Cushioned Plastic.

Weight Approx. : 100 gms.,300gms.

05 each

10.

Carpenter Pincer Forged carbon steel/chrome Vanadium steel with high quality rubber/PVC

Size. : 8", 9"

05 each

GROUP 2

11.

C Clamp Body: SG iron.

Screw and lever: High quality Steel.

Size: 4", 6", 8" 05 each

12. Corner Clamp Body: SG iron.(Spheroidal Graphite CI)

Jaw Width:2”/ 4" 05

13.

T- Bar Clamp Body : Carbon steel

Head &Jaws: cast iron/malleable iron.

Size: 3'’ & 4'’

05 each

14.

Carpenter vice quick grip type

Body: SG iron.

Head &Jaws : cast iron/malleable iron

Size: 6",8",12"

05 each

15. Adjustable Marking Gauge Size: 6" and scale graduated in mm 05

16. Adjustable Mortise Gauge Size: 6" and scale graduated in mm 05

17.

Firmer Chisel Set Material: Heat treated and forged alloy steel

Size(mm): 6,10,12,16,20,24,30 05 each

18.

Mortise Chisel Set ( bevel Edge) (JK/Eastman/Taparia/Pye)

Material: Heat treated and forged alloy steel

Size(mm): 6,10,12,15,20,25 05 each

19.

Paring Chisel Set Material: Heat treated and forged alloy steel

Size(mm): 6,10,12,16,20,24,30 05 each

20. Gouge Chisel Set Material: Heat treated and forged alloy

steel Size(mm): 6,10,12,16,20,24,30 05 each

21. Adze Size: 3" angle edge , weight: 1kg 05

22. Trammel Size:300mm 05

23.

Triangular File(JK/Eastman/Taparia/Pye)

Handle: High quality rubber/plastic for grip

Size: 100,150,200mm 05 each

24.

Flat Basterd File(JK/Eastman/Taparia/Pye)

Single cut and double cut type

Size: 12" 10

25.

Try Square(JK/Eastman/Taparia/Pye)

Blade Material: cast steel/SS with inch and mm Graduation

Size: 6", 8", 12 ",18" 05 each

26. Four Fold wooden Rule Size: 2" with inch and mm graduation 10

27. Measuring Tape/Pocket Tape

Tape Length: 3m, 5m 05 each

28.

Water stone/Oil stone

Grit size: 800,1000,1200

Dimension:15cm×5cm×2.5cm(Approx) 05 each

29. Two Sided Diamond Plate

Grit size: 1000,1600

Dimension:9"×5"×.8"(Approx) 05 each

30. Adjustable Honing Guide Width of Grip:3 to 65 mm 05

31. Spring Caliper (Inside & outside type) (JK/Eastman/Taparia/Pye)

Size: 150 mm(Approx)

10

32. wing Compass Size: 300mm(Approx) 10

33. Sprit Level 0.5 mm accuracy without magnet. 10

34.

Screw Driver Set(JK/Eastman/Taparia/Pye)

Size: 3mm,4mm,6mm,8mm,10mm;Lenghth: 100,150,200,250,300mm Engineering pattern

05 sets

35. Tool Trolley With 7 drawers or more 02

36. Round Die Set for thread cutting with Handle

Size: 1/2" to 1" 05

37. Tap Set with Handle Size: 1/4", 1/2", 3/4",1" 02 each

38. Bar Bender Bending Capacity: 8mm to 13 mm 05

39. Pipe Bender Hydraulic Type

Bending Capacity: 1/2" to 2" 05

40. Pipe Vice Hinged Type

Size: 2"-3" 10

41.

Fitters Vice Fixed and Swivel Base Type, chrome plated screws

size: 3", 6"

05 each

42. Surface Plate 400×400 mm, Steel 05

43. Adjustable Angle Plate 20×10 cm 03

44. Anvil (single bick type) Approx. Weight: 50 Kg with stand 02

45. Adjustable Wrench(JK/Eastman/Taparia/Pye)

Size: 6", 8" 05 each

46. Plier Box & slip Joint Type Size: 10" 05

47. Adjustable pipe Wrench(JK/Eastman/Taparia/Pye)

Size: 6", 8",12”,14”,18” 05+02 each

48. Ring End Spanner Set(JK/Eastman/Taparia/Pye)

Size: 6- 32 mm 05k+01

49. Open Ended spanner JK/Eastman/Taparia/Pye)

3mm to 32mm 01each

50. Double End Spanner Set(JK/Eastman/Taparia/Pye)

Size: 6×7mm to 27× 32 mm 05

51. Flat cold Chisel Size: 6", 8", 10" 05 each

52. Round Chisel Size: 6", 8", 10" 05 each

53. Number Punch Size: 5mm, 0-9 05

54. Center Punch Size: 4" 05

55. Plumb Bob Weight: 50 Gms 05

56. Bevel Square Size: 12" 05

57. Plumber Saw Size: 300mm 05

58. Cutting Pliers(JK/Eastman/Taparia/Pye)

Size: 200 mm" 10

59. Flat Rough File(JK/Eastman/Taparia/Pye)

Size: 14" single and double cut type 10

60. Flat Smooth File(JK/Eastman/Taparia/Pye)

Size: 6",8",12" 05 each

61. Half Round Smooth File(JK/Eastman/Taparia/Pye)

Size: 12" 10

62. Half Round Rough File(JK/Eastman/Taparia/Pye)

Size: 12" 10

63. Square Rough & smooth File(JK/Eastman/Taparia/Pye)

Size: 12" 10

64. Knife Edge File Smooth Size: 8" 10

65. Odd Leg Caliper Size:150mm 10

66. Micrometer ouside and Inside(JK/Eastman/Taparia/Pye)

Size: 0-150 mm, digital/Analog 05

67. Digital Vernier Caliper Set(JK/Eastman/Taparia/Py

Main Scale Size: 150 mm, 300mm, 450mm

02 each

e) Least count: 0.01mm

68. Steel Rule Size: 150 mm, 300mm, 450mm with Inch

and mm graduation 05 each

69. v block with Clamp Size: 6"×7”×7” 10

70. Depth Gauge(JK/Eastman/Taparia/Pye)

Size: 12" 05

71. Engineering Try Square Set(JK/Eastman/Taparia/Pye)

Size: 8",12",18" with Inch and mm graduation 05 each

72. Combination Pliers(JK/Eastman/Taparia/Pye)

Size : 6" 10

73. Allen Key Set(JK/Eastman/Taparia/Pye)

size: 24, 25, 27, 30, 32, 36, 42 and 46 mm. 05 set

74. Ball peen Hammer with Handle

Weight: 800gms, 1000gms. 05 each

75. Pocket Tape Size: 3m & 5m 05 each

76. Height Gauge Size: 12". 10

77. Sledge Hammer with handle

Weight: 1000gms. 10

78. Sprit Level Magnetic type Size : 300 mm 10

79. Chisel diamond point Size: 6 x 150mm 05

80. V block V bock with clamp

Size: 3” 05

81. Work Bench A Heavy wooden top (8'×3') , fixed with

2 swivel type bench vices 100mm Jaw 05

82. Welding Partition Screen Dark fiber type 10

83. Welding Goggles Standard safety goggles for welding

Shatterproof polycarbonate lenses with anti-scratch coating

Soft foam protection guards dust and perspiration from the eye

20

84.

Welding Gloves Good quality Leather and Kevlar stitched

Trigger-patch on index finger for extended wear

Reinforced palm patch.

Size: Medium and large 10

85. Arm & leg sleeves Good quality Leather and Kevlar stitched 10

86.

Apron Leather

size: Medium and Large

Quality leather to withstand sparks and spatter

10

87.

Welding Helmet As per applicable safety standards

Viewing Area – 9.22 sq. in. / 3.85 x 2.38 in (97 x 60 mm)

10

88. Smithy Tongs Size: 12", Flat mouth type 10

89. Chipping Hammer with handle

Weight: 250gms. 500gms. 05 each

90. Smithy Try Square Size: 18"×12" 10

91. Measuring Gauge Wire gauge and Sheet Gauge 10

92. Steel Wire Brush Size: 6",9" 10 each

93. Divider Firm Joint Size: 8" 10

94. Fix Spanner set Size: (10 Nos) 6 mm to 27 mm drop

forged 05 sets

95. Bench Vice Size: 4"& 6" Jaw ,swivel type 10

96. Sprit Level Magnetic type Size : 300 mm 05

97.

Anvil Weight: 50kg with stand, single bick long pattern 05

98. Mobile Weld fume Extractor Capture: 12 ft. extraction arm

Distance to arc: Up to 18 in. with extraction arm

Filter type: self cleaning

Input voltage: 220-240V, 50 Hz

01

99. Stakes & stake Holder set Hatchet stake , Pipe stake, Funnel stake, Half moon Stake, Mandrel, side stack, round bottom and ball head stake, tinman horse stake with heads.

Note: Each type of stake to be provided in a set of 3 different sizes and 1 stake holder with lock pin and 1 star stake plate

01 set

100. Hand lever Shear cutter Blade Length 300mm.

Cutting capacity: 5mm Sheet 6mm Bar,13mm Round

02

101. Swage Block Caste Iron swage Block :20"×20"×7" with cast Iron stand

05

102. Swage Block Caste Iron swage Block :15"×15"×5" with cast Iron stand

05

103. Cast Iron Mandrel Cone 75mm Dia. Tapering to 220mm Dia. 600mm High

02

104. Hot or Square Punch Size:1/4",3/8",1/2" 05 each

105. Wing Compass Size: 8" 05

106. Spring Divider(JK/Eastman/Taparia/Pye)

Size: 6"

05

107. Tin snip/Tin Cutter- Heavy duty

Quality PVC grip, Size: 10" to 12" 10

108. Steel Scriber set single ended light duty: 4"

Single ended heavy duty:6"

Double Ended, a needle point one end and a chisel other end:6"

Double Ended, one straight point and other bent at 90 deg( Light and Heavy Duty Type): 8"

10

109. Rubber Mallet with handle weight: 500gms, 800gms 05 each

110. Hand operated sheet folding machine

Folding Capacity : 1 m length , 1.6 mm thick sheet of metal 01

111. Scientific Calculator with solar

12

112. Engineering Drawing Models

(Shaft Couplings,Foot step bearing 01 each

113. Electric Kettle 1.5L 01

114. LED Lamps 9 V,16W 5

115. Ball Bearing 6201 and 6202 5 each

116. Hammer 5Kg,4Kg,3Kg,2Kg,1Kg 2 each

117. Fuller set (Top and Bottom) Size: 1/8",1/4", 3/8" 05 each

118. Straight peen/ Smiths Hammer

Weight: 300gms, 500gms, 800gms,1500gms

05 each

119. Straight peen/ Smiths Hammer

500gm,1000gms 05 each

120. Sledge Hammer 1000gms, 1500gms,2000gms 05 each

121. Handies Standard as per requirement 10

122. Poker Standard as per requirement 10

123. Smiths Forge Shovel Features: Long Handled

Protective Qualities: Rust Resistant

Care and Cleaning: Wipe Clean With a Damp Cloth

Blade Dimensions: 10.0 " L x 8.0 " W

Dimensions: 64.0 " L x 10.0 " W x 5.0 " H

05

124. VernierCaliper Main scale :18", LC=0.02mm 05

125.

Gloves High temperature application Kevlar Gloves with polymer grip

10

126. Wall Clock 12

127. Steel Tub Galvanized Volume: 20 Liters 02

128. Storage Bin Plastic Size:2'×1 1/2'×3' 05

129. G.I. Plane Sheet 24 gauge, 26 gauge, 28 gauge 8X4ft. 2 each

130. M.S. Sheet 22 gauge, 24 gauge, 26 gauge

900mmx2500mm 2 each

131. MS Flat (50mm x 6mm) 2 Quintal

132. MS Round (6mm,8mm, 12mm, 25mm, 32mm) 2 each

133. Cast Iron Block Rectangular

150mmx100mmx50mm 5 each

134. Cast Iron Block Square 100mmx100mmx100mm 5 each

135. Soldering Wire 60x40 2 pkt

136. MS Square Bar (10mm, 12mm) 2 each

137. Aluminium round Bar 12 mm 3 lengths

138. Aluminium flat 1 ¼”x 8 mm 5 lengths

139. Wood Kail 2’X2”X2” 5

140. M.S. Electrodes 3.15x350mm (10 no. s.w.g.) 10 pkts.

141. Wire Nail ½”, 1”, 2”, 3” 2 Kg each

142. Insulation Tape Steel Grip 2 dz.

143. Cutting Oil as per BIS : 1115-1986 20 litre

144. Soap Lifebouy 24 piece

145. Aluminium Rivets ¼”, 1/8” 2 kg each

146. Brass Rod 10 SWG 2 pkt.

147. Filler Rod 10 SWG 2 Pkt

148. Flux Powder for tining ½ Kg pack

2 pkt.

149. Boring Bar (Boring Tool) 01

150. Parting Tool Holder with tool

01

151. Socket Set with reversible ratchet

3mm to 32mm,drive3/4” 01

152. PVC Clamp ½”, ¾”, 1” 12 eeach

153. Steel Screw ½”, ¾”, 1”, 2”, 3” 1 pkt. each

154. G.I. Pipe ½”, ¾”, 1” 3 length each

155. G.I. Socket ½”, ¾”, 1” 12 each

156. G.I. Tee ½”, ¾”, 1” 12 each

157. G.I. Elbow ½”, ¾”, 1” 12 each

158. G.I. Union ½”, ¾”, 1” 12 each

159. G.I.nipple ½”x4” 12 nos

160. Valve cock 1/”, ¾” and 1” 10nos

161. Angle valve ½” 10nos

162. Suter (Thread) 5 dz

163. Safeda 250gm 12

164. Welding Glass (Black, White)

50 piece

165. Sand Paper 60, 80no. , 100 no. 12 each

166. CFL 15, 25, 40 (W) Havels/ Anchor/ Philips 6 each

167. Bench Vice 3” Jaw 08

168. Nail 1/2”, 17 No. 1”, 2”,3”,4” 1 kg

169. H.S.S Drill Bits 4mm,5mm,6mm,7mm,8mm,9mm,10mm. 10 each

170. H.S.S.taper shank drill bit 13mm,15mm,16mm,18mm,22mm 10each

171. Drill Chuck 0-12mm with key 5nos

172. PVC Pipe 15mm for watering 200m.

173. Fevi Col 1kg packing

174. Lakh dana 1 Kg

175. Molasses(Raab) 100 Kg

176. Moulding Boxes 1x1ft.

2x2ft (cope and Drag) 05 each

177. Paint Black, White, Grey(Asian,Burger,Nerolac)

1 liter packing 20lts each

178. Paint brush 3”,4”,6” 10 each

179. Wood Primer 10 lts

180. Metal Primer 10lts

181. PVC pipe 4” (Heavy duty) 10nos

182. Collar Socket 4” (Heavy duty) 15nos

183. Tee 4” (Heavy duty) 5nos

184. Bend 4” (Heavy duty) 15nos

185. Solvent Solution 500gms

186. English Seat W.c 5nos

187. Cistern Low level 5nos

188. Seat cover 5nos

189. Jet Pipe heavy 20mm

190. Seat cover Clamp 20pairs

191. White Cement 5kgs

192. White zinc Safeda 2kgs

193. Bib Cock ½” Iron 20nos

194. Bib Cock ½” C.I. 20nos

195. PVC connection pipe 18” 50nos

196. PVC Connection pipe 24” 20nos

197. Face Heavy Duty 50nos

198. Disk Face 50nos

199. Ball cock ½ Brass 50pcs

200. Ball valve ½ Brass 50nos

201. Tank Nipple brass ½”,3/4”,1”,1x1/4” 20 each

202. Motor Pump 0.5 H.p.

1.0 H.p 01 each

203. Check valve Brass ½”,3/4”,1”,2”,3” 03 each

204. Main Hole !2’x12” C.I 04nos

205. Sewing Machine with stand Make: USHA /Singer/Toshiba/Brother 10 Nos

MECHANICAL/ AUTOMOBILE ENGINEERING DEPARTMENT

S.NO NAME OF EQUIPMENT SPECIFICATIONS TENTATIVE QTY PRICES PER UNIT INCLUSIVE OF TAXES

1 R-22 Gas 10 kg each 02 cylinder

2 R-134a Gas 500 gms each 10 Cylinder

3 Copper tube ¼ “ 05 roll

4 Copper tube ½ “ 05 roll

5 Copper tube 5/8 “ 05 roll

6 Copper brazing rod 02 kg

7 Compressor 1.5 rotary 01 No.

8 Compressor 1.5 reciprocating 01 No.

9 Compressor 1/6 Hp 02 No.

10 Car A/c compressor 01 No.

11 Butane gas for brazing 20 cylinder

12 Butane gas brazing torch 04 Nos.

13 Flare Nut ¼, 3/8, ½, 5/8 20 Nos. Each

14 Toner for Work-Center Pro 423,428 Xerox Make 01 no

15 Cartridge for HP printer 1007 (88 A) 01 no

16 Cartridge for HP printer 1005 (34 A) 01 No

17 Hydraulic oil (Grade 68) 100 ltrs

18 Grease (Castrol) 5 Kg

19 Cotton Waste 10 Kg

20 Dhoti 10 mtrs

21 Weight Pans 24 Nos.

22 Drawing Pins 10 packs

23 Thread 20 rolls

24 Weights (Steel) 5,10,20,50,100,200,

500 gms

12 each

25 Specimens of Brass, Bronze, Mild

Steel, HSS, Gun Metal, Aluminium

12 each

26 Button Cells, Battery Cells, Pencil

Cells

24 Each

27 UPS Batteries (12 V) 120 Nos.

28 LPG Cylinder (5 Kg) with pipe,

regulator, blow torch

for brazing

1 No

29 Scanner HD 1 No

30 Brake oil 25 lts

31 Hydrometer 36 nos

32 Engine oil 25 lts

33 Hose Pipe 20mts

34 Gear oil SAE 90 10lts

35 Grease White 5kgs

36 Tubeless puncture kit 02kits

37 Solution Tube 1pkt

38 Garage tool kit trolley type 5 drawer 02nos

39 Piston ring ecpander 01no

40 Piston ring compressor 01no

41 Spark plug spanner 02

42 High Voltage discharge tester 02nos

43 Vacuum gauge for engine cylinder 01no

44 Compression gauge for engine

cylinder

01no

45 Universal Puller 01no

46 Tyre inflation pressure gauge 1.wall mounted type

2.Pen type

01 each

47 Lever Type grease gun 300cc upto 6000psi 01no

48 Hot Puncture machine Standard size 01no

49 Roller for making cold puncture Standard size 01no

50 Oil spray Can 250cc 02nos

(Er. Ritu Jamwal)

(Chairman, D.L.P.C) Principal

Govt. Polytechnic, Jammu