TENDER - CIVIL & INTERIOR FURNISHING WORKS · PDF fileMaking small holes in internal/external...

CIVIL & INTERIOR FURNISHING WORKS

PART II– FINANCIAL BID Page 0

TENDER - CIVIL & INTERIOR FURNISHING WORKS

FOR

BRANCH

AT

APMC MARKET VASHI – TURBHE BRANCH

Shop No. 1001 to 1004, 2001 to 2002 and 3001 to 3002,

B wing, Mayuresh Trade Center (City Mall) Vashi, Navi Mumbai 400 703.

ARCHITECTS: M/s Prakash Walavalkar & Associates 102, Ameya Tower, 1139 Pavwala Street, Grant Road Mumbai 400 004 Tel: 28822143 / 23855343 Mobile: 9869015343 Email: [email protected] [email protected]



CONTENTS

INDEX PAGE NO

INSTRUCTION 2

BILL OF QUANTITIES 3 – 14

DRAWINGS 15



INSTRUCTIONS

1. The Bill of Quantities shall be read in conjunction with the Drawings, Conditioners of Contract

and Specifications, as these documents are jointly explanatory and descriptive of the works included in the Contract.

2. General directions and descriptions of work and materials given elsewhere in the Contract documents are not necessarily repeated in the Bill of Quantities. Reference is to be made to the other documents for information.

3. The Contractor shall be deemed to have visited the site before preparing his Tender and to have examined for himself the conditions under which the work will be priced and all other factors affecting the execution of the work and the cost thereof.

4. The Quantities of work and material in the Bill of Quantities are not to be considered as limiting or extending the scope of work to be done and materials to be supplied by the Contractor. The quantities in the Bill of Quantities are an estimate of the amount work but the work will be measured on complete and the contractor will be paid on the actual measurement of work approved by the Architect.

5. Any special methods of measurements used are stated at the head of or in text of the Bills of Quantities for the items affected. All other items are measured net in accordance with the drawings and no allowance has been made for wastage. Unless otherwise specified measurements shall be as per relevant Indian Standard.

6. A price or rate in figures is to be entered against the item in the Bill of Quantities, whether quantities are stated or not. Item against which no price is entered will be considered as covered by other prices or rates in the Bills.

7. The prices and rates interested are to be the full inclusive value of the works described under the various items, including all costs and expenses which may be required for the completion of the work described, together with all cost and obligations set forth or implied in the conditions of Contract, Specifications and the Drawings.

8. Some finishing items may be quantity wise completely altered (either added or omitted) and the same shall not affect any rates quotes.

9. Where prices have been entered against Lump sum items, payment for such affected items shall be made in proportion to the extent of which works have been done at the time of billing and the same is at discretion of the Architect.

10. “Providing and Fixing” shall mean that the Contractor has to provide such materials not being procured and borne by the Bank, but which are required for the item and if no materials need be provided by the Contractor, the rate shall be only for fixing of the component covered in the item.



BILL OF QUANTITIES

Sr. No.

Description Unit Qty Rate Amount

A Civil Works

A1

Dismantling Existing Flooring / Ceiling / Partition / Loft / Walls / Plaster / Doors / Windows etc as directed by the architects. Rate Including removal of debris from site and dumping the same in the nearest municipal dump.

L.S. 1.00

A2

Making small holes in internal/external brickwork, chiselling etc. and making good the same, if required to enable the Allied Contractors, for ex AC, PLUMBING , ELECTRICAL AND LAN etc.to carry out their installation work during the course of the project.

Nos 5.00

A3

Providing and Laying plain cement concrete PCC of 1:3:6 of thickness of 75mm to100mm over the entire floor area in line and level as indicated by the Architect with vibrator for compaction inclusive of curing etc.The finished surface to be smooth and level in power trowel finish without any undulation. Cost to include finishing of edges near junction-boxes, etc. Complete with all relevant debris, etc. to be removed from the site, on a day-to-day basis.

Sq.Ft. QRO

A4

6" THK BRICK WALL WITH PLASTER Constructing 4.5” thk. Brick wall in 1:5 cement mortars. Brick used shall be of best quality kiln burnt, having sharp edges & giving clear ringing sound when struck against each other. Necessary RCC lintels of depth 4 ½” above door opening to be provided. A 4 ½” R.C.C. Patli Beam shall run horizontally @every 3’-0” c/c height of the wall. The walls should be extended up to the ceiling height by leaving space for return air for A/C ducting as directed by Bank / Architect. The walls to be plastered ¾” thick C.M.1:4 on both sides. The walls should be finished in proper workmanship and with neat finish.

Sq.Ft. QRO

A5

VITRIFIED TILES FLOORING & SKIRTING 600mm X 600mm Providing and fixing VITRIFIED Tiles approved make, shade and pattern as shown in the drg. / As approved by the bank / Architect. In CM1:4 in proper line and level without spacers for maintaining the grid lines. 3 of 7. Rate shall be inclusive of providing and laying necessary PCC and Cement Mortar for a thickness of 3" and joint filling compound of the same shade of the tiles

Sq.Ft. 25.00



A6

GRANITE SLAB FLOORING Providing and fixing

20mm thick machine cut and mirror polished Granite slabs of approved colour in length upto 2400mm, set in 20mm thick cement mortar 1:4, joint finished with neat cement slurry with matching colour including dressing the nosing and sides to the required shape etc. as directed for Flooring, Jambs, Cills, Trims etc. with sizes as per drawing. Rate to include final mirror polish after installation.

Sq.Ft. 50.00

A7

PANTRY PLATFORM IN BLACK GALAXY GRANITE (WITH SINK & COCK) Providing and laying platform of 2’-0” width (clear) and at 2’-8” height (top finished level) above floor level with 23mm thick granite slab ( Black Galaxy) with champhered and machine polished Bull Nosed edge. It shall be supported on vertical Brick wall 4.5" & Horizontal RCC slab 3" thick. Necessary cut outs to be made in the RCC slab and Granite slab with polishing the edges and providing 18" x 18" size S. S. Nirali sink without drain board (Nirali or equivalent make). The waste line to be connected through a Nahni Trap with necessary fittings. One jaguar continental C. P. Sink cock with swinging cast spout (no. 347) also to be provided

R.ft. 6.00

A8

Providing/Applying on external/internal walls, Floors etc at all levels where water leakage is an issue 25mm thick Waterproof Cement Plaster Internal in line, level and plumb including "Roff" Liquid Chemical to be used or alternate chemical to be approved by Architect complete as directed including scaffolding, finishing & removing of existing plaster etc.

Sq.Ft. 25.00

A Total Civil Works

B Fabrication & Window Works

B1

Collapsible Gate – P&F collapsible gate, with interlocked arrangement in heavy approved sections, including 2" frames on sides, top and bottom guide rails with first quality enamel paint. For Branch Entrance

Sq. Ft. 60.00

B2

M.S.GRILLS - Providing and fixing MS Grills for windows / ventilators etc. using 12mm M. S. round or square bar grills at 4" C/C fixed as per design / drawings or as directed by Bank / Architects. The works should be done with all necessary fittings etc with proper workmanship and with 2 coats of anti rust paint and 2 coats of Synthetic Enamel paint.

Sq. Ft. 50.00



B3 Rolling Shutter – P&F rolling shutter of 20 gauge MS sheet, including floor locks, guide rail, first quality enamel paint

Sq. Ft. QRO

B Total Fabrication Works

C Furnishing Works

C1 Partly Glazed Partition for Cash Cabins Sq. Ft. 300.00

Providing and fixing in position 7’-7” high partly glazed partition for Cash Cabins including door frame work at 2’ x 2 ‘grid (horizontally and vertically) comprising of 2” x 1½” T.W. Section and / or as per frame work shown in the drawings with 6mm plywood on both sides finished with 1 mm thick laminates of approved shade and colour as shown in drawings. Item to include 8 mm thick glass with etching and frosting as per design and 2”x 2” T.W. member for door sides and glass sides and T.W. door frame to take 8 mm thick glass with etching and frosting. The door will be provided with T.W. louvers finished in melamine polish of matching laminate colour. The doors are also to be provided with Godrej Night Latch. Two wooden trays are also to be provided as per drawing. Necessary cut-outs are to be provided in the glass and the edges of the glass cut-outs are to be finished in mirror polish. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects

C2 P & F non-transparent white film: Sq. Ft. 235.00

On glazed surfaces from inner side in pattern as directed.

C3 Cash Counter: R. Ft. 12.00

Providing and fixing in position Cash Counter 2’-9” wide comprising of the following :

Working top made with 25mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1¼”X1” Teak Wood moulding finished with melamine polish. Inside edge will be provided with ½ “x 1” T.W. beading Patti with melamine polish.

Vertical fascia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminates of two different shades.



Vertical drop (horizontal band) shall be provided on the fascia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1 mm thick groove shall be provided at the joint of two different shades of laminate.

Glazed partition of 1’-4” height above working top provided with 12mm thick toughened and frosted glass besides non-transparent film from inside fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. The exposed edges of the glass shall be finished in mirror polish.

Transaction top shall be provided with 12mm thick toughened glass (partly glazed partly frosted) fixed horizontally with concealed Stainless Steel D bracket. Both exposed edges (inside and outside) shall be moulded and finished in mirror polish.

Glazed partition provided with 12mm thick glass (Clear) above the slit to be fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. The exposed edges shall be finished in mirror polish.

7’-7” high Boxing (10”x 10”) made with 18mm thick plywood as per drawing with 1-6” horizontal extension at the top including providing and fixing 6 mm thick square frosted glass at a height of 5'-11” above Finished Floor level.

1’-9” high boxing (5”x 5”) made with 12 mm thick plywood finished with 1 mm thick laminate are to be provided.

Telescopic CPU Stand / readymade Keyboard tray shall be provided of approved model and make.

Footrest made with T.W. section of size 4”X1 ½ “finished with French polish.

Drawer units as per drawing shall be provided and each drawer should have vertical partitions for keeping the currency notes and multipurpose Godrej locks. Fascia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank

Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/Telephone wire conduiting. The item to include all necessary hardware and fittings in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary beadings with matching melamine polish for fixing the glass are to be provided as per drawing/ as directed.

C4 Front Office Counter: R. Ft. 16.00

Providing and fixing in position Front Office Counter 2’-6” wide comprising of the following complete in all respects:-



Working top made with 25mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with1¼”X1” Teak Wood moulding finished with melamine polish. Inside edge will be provided with ½ “x1” T.W. beading Patti with melamine finish.

Vertical fascia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with1mm thick groove at the joint of laminates of two different shades.

Vertical drop (horizontal band) shall be provided on the fascia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1 mm thick groove shall be provided at the joint of two different shades of laminate.

Glazed partition above working top to be provided with 12mm thick clear glass cut to the standard shape fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. The exposed edges of the glass shall be finished in mirror polish.

3’-10” high Boxing (10”x10”) made with 18 mm thick plywood finished with 1 mm thick laminate including providing and fixing 6 mm thick square frosted glass at a height 3’-2” above finished floor level.

1’-9” high Boxing (5”x5”) made with 12 mm thick plywood finished with 1 mm thick laminate.

Vertical supports made with 18 mm thick plywood finished with white enamel paint.

Telescopic CPU Stand/ readymade Keyboard tray shall be provided of approved model and make.

Footrest made with T.W. Member of size 4”X1 ½ “finished with French polish.

Drawer units as per drawing shall be provided with multipurpose Godrej locks in

Each drawer. Fascia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank

Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/Telephone wire conduiting.

The item to include all necessary hardware and fittings in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the front. Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary beadings with melamine or fixing the glass are to be provided.



C5

Partly Glazed Full Height Partition Providing and fixing in position including door as shown in the in frame work at 2’ x 2 ‘grid (horizontally and vertically) comprising of 2” x 1½” T.W. Section and / or as per frame work shown in the drawings with 6mm plywood on both sides finished with 1 mm thick laminates of approved shade and colour as shown in drawings.

Sq. Ft. 535.00

Item to include 8 mm thick glass with etching and frosting as per design and 2”x 2” T.W. member for door sides and glass sides and T.W. door frame to take 8 mm thick glass with etching and frosting. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. (Note: In case of false ceiling, the vertical T.W. members to be fixed with pucca ceiling but the area of partition payable will be below the false ceiling only).

C6

Partly Glazed Low Height Partition Providing and

fixing in position partly glazed low height partition (21/2” thick) in frame work with T.W vertical members at 2’ c/c and 3 horizontal members at equal distance comprising of 2”x 1½” T.W. Section with 6 mm plywood on both sides finished with 1 mm thick laminates of approved make and .Item to include 12 mm thick glass (clear/frosted) to be fixed as shown in drawing. The exposed edges of the glass to be finished in mirror polish. T.W runner should be melamine polished in matching colour of laminate etc complete in all respects.

Sq. Ft. 85.00

C7

Solid Full Height Partition - Providing & fixing in position solid Full Height Partition in frame work including door in 2’x 2’ grid (horizontally and vertically) comprising of 2”x 1½” T.W. Section with 6 mm thick plywood on both sides finished with 1 mm thick laminates of approved make and colour. Item to include 2” x 2” T.W. member for door-frame. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects.

Sq. Ft. 575.00

(Note: In case of false ceiling, the vertical T.W. members to be fixed with pucca ceiling but the area of partition payable will be below the false ceiling only).



C8 Full height Storage / Low Height Storage / Back Storage(Credenza)

Sq. Ft. 250.00

Providing and fixing in position Full height Storage / Low Height Storage/ Back Storage(Credenza) as shown in Drawing respectively using Plywood of required thickness finished with 1mm thick laminates as shown in the drawing and all other sides shall be finished with white enamel paint as detailed therein.

The Storage Units shall be provided with handles (Stainless Steel finish) as per approval of the Project Consultant / Bank. All exposed plywood surfaces to be finished with 1mm thk. Laminate of approved make & shade and all exposed edges of plywood to have 1" x 1/4" T.W. lipping. All exposed T.W. sections to be melamine in matching colour laminate and internal surfaces to have white enamel paint as directed. Item to include all necessary hardware and fittings in Stainless Steel finish, Godrej multi-purpose locks including magnetic ball catcher etc., complete in all respects

C9 Manager’s Table R.ft. 6.00

Providing and fixing in position Manager’s Table of size 6’x 2'-9" as per drawing / Officer’s Table of size 4’-6” x 2’-3” as per drawing including Side Storage(Credenza) by using 25mm thick plywood for top and 18 mm thick plywood for all other horizontal and vertical members. Telescopic CPU Stand/ ready -made Keyboard tray shall be provided of approved model and make. Footrest made with T.W. Member of size 4”x 1 ½ “finished with French polish.

Side Storage (Credenza) as per drawing shall be provided. Fascia of Side Storage (Credenza) shall be finished with 1mm thick laminates as shown in the drawing and all other sides shall be finished with white enamel paint. The Side Storage (Credenza) shall be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. All exposed plywood surfaces to be finished with 1mm thk. Laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1" x 1/4" T.W. lipping. All exposed T.W. sections to be melamine polished and internal surfaces to have white enamel paint as directed. Item to include plywood boxing, all necessary hardware and fittings in Stainless Steel finish, lipping to all edges etc. complete in all respects



C10 Officer’s Table Rft. 20.00

Providing and fixing in position Manager’s Table of size 6’x 2'-9" as per drawing / Officer’s Table of size 4’-6” x 2’-3” as per drawing including Side Storage (Credenza) by using 25mm thick plywood for top and 18 mm thick plywood for all other horizontal and vertical members. Telescopic CPU Stand/ ready -made Keyboard tray shall be provided of approved model and make. Footrest made with T.W. Member of size 4”x 1 ½ “finished with French polish.

Side Storage (Credenza) as per drawing shall be provided. Fascia of Side Storage (Credenza) shall be finished with 1mm thick laminates as shown in the drawing and all other sides shall be finished with white enamel paint. The Side Storage (Credenza) shall be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. All exposed plywood surfaces to be finished with 1mm thk. Laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1" x 1/4" T.W. lipping. All exposed T.W. sections to be melamine Polish and internal surfaces to have white enamel paint as directed. Item to include plywood boxing, all necessary hardware and fittings in Stainless Steel finish, lipping to all edges etc. complete in all respects

C11 Staff Table / May I Help U Table Rft. 16.00

Providing and fixing in position Staff Table of size 4' 0" x 2' 0" as per drawing by using 25mm thick plywood for top and 18 mm thick plywood for all other horizontal and vertical members. Telescopic CPU Stand/ readymade Keyboard tray shall be provided.

Drawer units as per drawing shall be provided with multipurpose Godrej locks in each drawer. Fascia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank.



All exposed plywood surfaces to be finished with 1mm thk. Laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1" x 1/4" T.W .lipping. All exposed T.W. sections to be melamine an internal surface to have white enamel paint as directed. The item to include plywood boxing, all necessary hardware and fittings in Stainless Steel finish, lipping to all edges etc. complete in all respects.

C12 Aluminium Heavy Duty Front Glazing with powder coated sections

Sq. Ft. 50.00

Providing and fixing fully glazed heavy duty aluminium sections (14 Gauge) at the main entrance as shown in the drawing. Glazing shall consist of approved make heavy duty 6" x 2" sections for the top & bottom rails and 2" x 2" sections for the vertical styles. 10mm thk. Approved make clear float glass shall be provided and fixed in the framing. Rate shall include necessary etching film / LOGO, and any necessary hardware items. (Heavy Duty 6" & 2" thick frames(14 Gauge) - approved make)

C13 Wall & Column Panelling In Branch: Sq. Ft. 1150.00

P & F 1 ½” x 1” T.W. frame work covered with 12mm commercial plywood & laminating as per new brand image to mate and match rest of décor.

Laminate 3 - ‘Silicon 9850SF’

Laminate 4 - ‘Greenlam 9001’

C14 Wall / Column Panelling (Silver laminate): Sq. Ft. 375.00

Framing in 2” x 1” T.W. covered with 12 mm comm. ply & finished with Silver laminate (Greenlam 9001 Silver)

C15 Wall & Column Panelling In E- Lobby Sq. Ft. 490.00

P & F 1 ½” x 1” T.W. frame work covered with 12mm commercial plywood & laminating as per new brand image to mate and match rest of décor.

Lamination inside the E- lobby as per new brand image for E-lobby. Lamination in the branch area to mate and match existing laminate in the banking hall.

C16 Glazed Divider at E_LOBBY Sq. Ft. 75.00

Providing and fixing fully glazed divider in 12mm thick toughened glass, fixed with approved SS bracket as directed



C17 Roller Blinds: Providing & fixing approved Roller blinds as directed.

Sq. Ft. 100.00

‘MAC’ ‘Vista’

C18 Soft Boards: Sq. Ft. 50.00

P & fixing soft board panelling directly on wall / column [basic fabric cost Rs.150/-Mtr.]

P & F 12mm thk soft boards covered with approved with fabric on 12 mm thick comm. plywood back as directed. Work includes frame out of 1” x ½” TW moulding with melamine polish to match rest of the décor.

C19 Providing & Fixing 35mm Solid flush single door: Nos. 3.00

(Overall size 3'-0" x 7' 0" ht.) Finished in laminate completely with hardware such as Dead lock, handles, floor springs.

Laminate 3 - ‘Silicon 9850SF’

Laminate 4 - ‘Greenlam 9001’

C20 Branch & E-Lobby Entrance Door Sq. Ft. 60.00

Providing and fixing Entrance Door (glazed) in Silver Anodized aluminium door section (Jindal make) in top and bottom, glazed with 12 mm thick glass of approved make with etching and frosting. Item to include floor springs, lock, all necessary hardware of Stainless Steel finish as approved by the Project Consultant/ Bank complete in all respects.

Door size: 8’ x 3’6” each. X 1 doors

C21 P & F Composite panel on Entrance Façade: Sq. Ft. 200.00

Out of aluminium composite panel boxing with PVDF coating & LDPE core laminated ‘Eurobond’/ ‘Altobond’ / ‘Alukbond’ Exterior grade 4mm thick with composite of (0.5mm-3mm-0.5mm) including fabrication for the same with aluminium sections, required hardware, silicon sealant (Dow, Corning 789) masking tape, etc. Complete in all respect.

C22 KEY BOX Nos. 1.00

Providing and fixing key box of size 1' 6"x1' 6"x 6" with all sides and back with 18mm thick comm. Ply wood and lockable glass shutters in 18mm ply , with 5 mm glass. Necessary hooks to be provided inside the box. All exposed areas and inside to be finished with 1 mm thick laminate of approved shade.



The edges of shutter and box to be lipped with steam beach beading polished with melamine. Rate shall be inclusive of all necessary approved fittings like hinges, locks, hooks etc. and any necessary hardware items.

C23 WALL MOUNTED WRITING TABLE 1'- 3" TO 1'- 6" WIDE

Nos. 2.00

Providing and Fixing wall mounted writing table as per design. The top and central partitions should be with 12mm thick float glass (approved make) with champhered edge (Bevelled edges) for top piece and verticals with edge polish. The glass should be supported on 18mm thick comm. ply base, rear and sides fixed to the wall. The bottom ply piece to be supported additionally with 2 Nos. of SS Brackets. The exposed faces should be finished with 1 mm thick approved laminate and the edges of ply wood to be provided with steam beach lipping finished with melamine.

C Total Furnishing Works

D False Ceiling Works

D1 Providing & fixing in position gypsum board:6”X6” COVE for Diffused lighting

R. Ft. 100.00

D2

False Ceiling (Gypsum Board) Providing & fixing in position false ceiling in Gypboard 12mm thick for horizontals & verticals fixed over G.I. framework as specified by India Gypsum Co. Ltd. Including trap doors for A.C unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges & locks with moulding 1” x 1” for edges including finishing with 2 Coats of White Plastic Emulsion Paint etc. complete in all respects.

Sq. Ft. 1750.00

(Note: Only the plan area will be measured for payment. No extra payment will be made for cut-outs, grooves, mouldings etc.)

D3 False Ceiling (Armstrong) Sq. Ft. 720.00

Providing & fixing in position false ceiling in Armstrong 600 x 600 mm x 15/16 mm Dune Supreme RH 99 Prima tile with Regular edge framework as specified by Armstrong Co. With Suspenders wherever required. Making necessary framework for A.C. ducting, if any, and necessary cut-outs for diffusers and light fittings, taping and finishing to proper line & level, including making



Grooves and trap doors for A.C unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges & locks with moulding 1” x 1” for edges including finishing with White Plastic Emulsion Paint etc. complete in all respects.

(Note: Only the plan area will be measured for payment. No extra payment will be made for cut-outs, grooves, mouldings etc.)

D Total False Ceiling Works

E Painting Works

E1

Painting Providing & applying White Plastic

Emulsion paint of Asian Paints/ ICI Dulux / Berger and Sporty Yellow-X104 shade of Royal Luxury Emulsion of Asian Paints in minimum 2 coats including scrapping, opening of existing cracks, filling up of “V” cracks with epoxy expandable putty to required depths, making good weak plastered / un-plastered surfaces with cement plaster wherever required. Item to include Plaster of Paris, primer, palti & making good existing surface to receive new paint including cleaning on completion of painting work etc. complete in all respects.

Sq. Ft. 2500.00

E2 Enamel paint to grills, metal surfaces, wooden

sections etc., as directed. Sq. Ft. 100.00

E Total Painting Works

F Municipal Formalities L.S. 1

Total Amount [A+B+C+D+E+F]

Discount

Total After Discount

Total Amount In Words :

Rate inclusive of all Material charges, Transportation, Local levies as applicable, Loading, Unloading, Lifting- Shifting, Erection, Testing , Commissioning, Scaffolding, VAT, Sales tax, any additional/ duties, excise, custom duty etc. as applicable.

Contractor Name :

Address

Sign & Seal



DRAWINGS – GENERAL LAYOUT

TENDER - CIVIL & INTERIOR FURNISHING WORKS · PDF fileMaking small holes in internal/external...

Documents

Transcript of TENDER - CIVIL & INTERIOR FURNISHING WORKS · PDF fileMaking small holes in internal/external...