TEMS Pocket Positioning Tool User's Manual

This manual is provided by Ascom Network Testing AB without any kind of warranty. Improvements and changes in this description due to typographical errors or inaccuracies in current information, or improvements to programs and/or equipment may be made by Ascom Network Testing AB at any time without notice. These changes will, however, be incorporated into new editions of this manual.

No part of this publication may be reproduced, transmitted, stored in a retrieval system, nor translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of the copyrighted owner, Ascom Network Testing AB.

TEMS is a trademark of Ascom.

All other trademarks are the property of their respective holders.

© Ascom 2010. All rights reserved.

Publication number: NT11-6191 ver 1.0

Contents

Contents

1. Introduction 1

1.1. TEMS Pocket Positioning Tool in Brief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2. Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2. Getting Started 2

2.1. Initial Tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22.2. Starting TEMS Pocket Positioning Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3. Using TEMS Pocket Positioning Tool 3

3.1. Positioned Map in TEMS Investigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63.2. Positioned Map in TEMS Presentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Index 9

NT11-6191 ver 1.0 i

TEMS Pocket Positioning Tool User’s Manual

ii

Chapter 1. Introduction

1. Introduction

This manual will assist you in using TEMS Pocket Positioning Tool.

1.1. TEMS Pocket Positioning Tool in Brief

With TEMS Pocket 7.x you can perform indoor logfile recording, by using an indoor map (for example a floor plan) and pinpointing your way through the building. The logfile with the measurement samples is stored together with the map in a zip container. When the *.zip file has been transferred to a computer, it can be opened from within TEMS Pocket Positioning Tool.

TEMS Pocket Positioning Tool is used to position (i.e. allocate a latitude and longitude value) the unpositioned map and update the geo positions for each sample in the corresponding logfile. The positioned map can then be opened in TEMS Presentation or in TEMS Investigation, superimposed on an ordinary background map. The logfile’s (positioned) measurement samples can be plotted on the indoor map and analyzed in the same manner as if they were samples from an ordinary logfile.

1.2. Prerequisites

To be able to use TEMS Pocket Positioning Tool, it needs to be installed on your computer. That installation is performed automatically if you have TEMS Investigation 10.0 (or later) or TEMS Presentation 1.2 (or later) installed.

NT11-6191 ver 1.0 1


2. Getting Started

This chapter guides you through a couple of actions to be taken prior to using TEMS Pocket Positioning Tool.

2.1. Initial Tasks

To be able to use the tool for positioning maps and corresponding measurement data, you need to:

• Transfer logfiles with indoor measurements and their corresponding maps (as zip archives) from your TEMS Pocket phone and save them locally on your computer or on a network directory.

2.2. Starting TEMS Pocket Positioning Tool

If you have TEMS Investigation 10.0 or later installed, TEMS Pocket Positioning Tool is found under Windows Start menu, where you select Programs Ascom TEMS Products Utilities TEMS Pocket Positioning Tool.

If you have TEMS Presentation 2.0 or later installed, TEMS Pocket Positioning Tool is found under Tools menu in TEMS Presentation.

2

Chapter 3. Using TEMS Pocket Positioning Tool

3. Using TEMS Pocket Positioning Tool

Start TEMS Pocket Positioning Tool.

The first action is to open the *.zip file with the unpositioned map and the corresponding logfile.

• Press the Open button on the toolbar.

NT11-6191 ver 1.0 3


• Browse for the zip file of interest. Mark it and press Open (or double-click it).

Now it is time to specify where the map and logfile shall be stored when the positioning procedure is complete. Perform the tasks mentioned in the following steps:

• Press the Properties button on the toolbar.

4


• Check the box Unzip archive, if you want to unzip the container with the logfile and the map. If so, the map image, a corresponding tab file and the logfile will be stored in an ordinary folder with the same name as the original zip container. If you uncheck this box, you have to unzip your map and logfile manually before you can use them in TEMS Presentation or TEMS Investigation.

The zip container is still stored in the same directory as when you opened it for positioning, and it will also be updated with the new map position and geo positions for the measurement samples after the positioning is complete.

• Specify the folder where the map image, the corresponding tab file and the logfile shall be stored (if you checked the box Unzip archive in the previous step) after the positioning procedure. Use the Browse button for convenience.

• Click OK.

On the right side of the map, you now enter Latitude, Longitude, the Width of the map picture, and Direction.

Latitude and Longitude values can be obtained from the outdoor map where the indoor map shall be positioned (in TEMS Investigation or TEMS Presentation). The entered values indicate the top left corner of the indoor map picture.

The Width is the estimated width (in unit [m]) of the entire picture, not necessarily the building or floor itself, from left to right. If the width is not OK in the map after the positioning, you simply enter a new Width value and start the positioning procedure again

Direction is the deviation from the outdoor map, from 0 to 360 degrees clockwise, and is used to adjust the direction of the indoor map before it is positioned in the outdoor map. If the direction is not OK in the map after the positioning, you simply enter a new Direction value and start the positioning procedure again.

NT11-6191 ver 1.0 5


When you have entered the values, you start the positioning process by pressing the Start button.

During the positioning, a progress bar indicates the progress. After the positioning, “Completed” is displayed next to the progress bar.

Now you can open the positioned map (from the folder specified previously under Properties) in TEMS Investigation or TEMS Presentation, favorably superimposed on an ordinary outdoor map.

3.1. Positioned Map in TEMS Investigation

You use the positioned map as an ordinary map, superimposed on the outdoor map. An example is displayed below.

6


3.2. Positioned Map in TEMS Presentation

You use the positioned map as an ordinary map, superimposed on the outdoor map. An example is displayed below.

NT11-6191 ver 1.0 7


8

NT11-6191 ver 1.0 9

Index

Index

Ddirection 5

Iinitial tasks 2

Llatitude and longitude values 5

Oopen the positioned map 6open the unpositioned map 3

Ppositioned map in TEMS Investigation 6positioned map in TEMS Presentation 7positioning complete 6prerequisites 1

Sstart positioning 6starting TEMS Pocket Positioning Tool 2storing the positioned map 4supported operating systems 1

Wwidth 5

www.ascom.com/tems

06

.20

10

© A

scom

20

10

. All

righ

ts r

eser

ved.

TEM

S is

a t

rade

mar

k of

Asc

om .

All

othe

r tr

adem

arks

are

the

pro

pert

y of

the

ir r

espe

ctiv

e ho

lder

s.

AScoM NETwork TESTiNg lEAdS ThE world iN providiNg bEST-iN-

clASS SoluTioNS To MEASurE, ANAlyzE, ANd opTiMizE MobilE

NETworkS.

The TEMS™ Portfolio offers a complete set of trusted solutions for drive

testing, benchmarking, monitoring, and analyzing network performance.

These state-of-the-art offerings facilitate the deployment, optimiza-

tion, and maintenance of mobile networks.

We are the industry leader, and our products are supplied to the

world’s top mobile operators, equipment vendors, and professional service

providers.

Ascom Network Testing Inc.1943 Isaac Newton SquareReston, Virginia 20190 | USAwww.ascom.com/tems

Ascom reserves the right to change specifications without notice. Ascom acknowledges all registered trademarks appearing herein.

http://www.ascom.com/tems

TEMS Pocket Positioning Tool User's Manual

Documents

Transcript of TEMS Pocket Positioning Tool User's Manual