Technical Data Sheetcms.condros.eu/Uploads/acotec/FILE_3b7ea79c-c187-43a5-b3f5-6313… · Norsok...

LET’S FACE CORROSION

Technical Data Sheet

T: +32 53 83 86 60

F: +32 53 83 69 88

M: [email protected]

W: www.acotec.be & www.humidur.be

Industrielaan 8

Zuid III

9320 Erembodegem (Aalst)

Belgium

Acotec nv

Humidur® FP QR

Pg. 1/6

Date: 16/02/2018

Humidur FP QR is a 2-component solvent-free modified polyamine cured epoxy system offer-

ing following benefits:

Compatible with most epoxy, polyester and vinyl ester coatings

Long term protection in highly corrosive environments: life expectancy over 30 years on thor-

ough prepare surfaces and 15 years on minimally prepped surfaces

Single coat system; No primers required

High chemical resistance to acids, alkalis, acids, oils, lubricants, detergents, ...

Environmentally friendly (100% solids, no solvents, no heavy metals, no coal tar)

Excellent abrasion resistance and impact resistance

Surface tolerant & Outstanding adhesion to substrate and interadhesion between layers

Capable of curing under water: can be exposed to water and precipitation immediately after ap-

plication

Capable of curing at freezing temperatures

NDT inspection allowed

Resistant to temperatures from -35°C to 150°C and to most fluids between pH 0 and pH 14

Cost-effective (LCCA conducted by DHV Royal Haskoning)

Product Description

Humidur FP Quick Repair, with its straightforward appli-

cation, has been specifically developed for the repair of

coatings and for small/ difficult to reach areas of applica-

tion. It comes in pre-dosed tubes and is applied by a stand-

ard dispensing gun. Only the amount that is needed, how-

ever small, is mixed automatically at the correct ratio in the

tip, eliminating waste and mixing errors. Thanks to this

unique application technology, the pot life is no longer rele-

vant.

Humidur FP QR has been designed to simplify coating repairs in the most extreme and ag-

gressive environments (marine environment, offshore wind and offshore oil & gas, petrochem-

ical industry, pipelines, …). It offers high quality repairs of coating systems in one layer. Hu-

midur FP QR can be easily spread out over the surface by brush.

The application of Humidur FP QR is carried out by means of a standard dispensing gun,

which is available all over the world. Only the amount that is needed, however small, is

mixed automatically at the correct ratio in the tip. The pot life becomes irrelevant and the re-

mainder of the tube can be used at a later moment.

Humidur FP QR is therefore ideal for use in the most difficult application conditions (e.g.

confined spaces, rope-access, …).

Recommended Use

Composition

Humidur FP QR consists of two components:

A is the base component and contains:

non-crystallisable epoxy resins,

high-tech modifying agents and elastifiers,

lamellar abrasion and impact resistant fillers,

colouring pigments

B is the hardener and contains:

polyamine hardener complex

TDS - Humidur® FP QR


T: +32 53 83 86 60

F: +32 53 83 69 88


Industrielaan 8

Zuid III


Acotec nv

Pg. 2/6

Date: 16/02/2018

Manufacturer’s Information

Acotec nv, with registered offices at Aalst, Belgium, is the developer and sole manufacturer of the Hu-

midur products, distributed worldwide through a wide network of agents and cooperative companies.

The proven lifetime of the Humidur coatings in practice is more than 30 years. Contact Acotec direct-

ly or visit www.acotec.be or www.humidur.be for reference projects or for other systems.

Product Data

SPECIFIC DATA FP QR

Density

@ 23°C

Component A ± 1,43 g/cm³

Component B ± 1,085 g/cm³

Mixture A + B ± 1,21 g/cm³

Solid content 100%

Flash point mixture A + B >100°C

Hardness Shore D > 74

Colour (gloss) (For colour stability (only esthetic) , apply Humidur TC on

top of Humidur FP QR)

Ask your Acotec representative

Practical thickness in one layer

400 µm

Minimal recommended thickness 400 µm

Covering

capacity (WFT = DFT)

Theoretical @ 400µm 0,48 kg/m²

Mixing ratio A : B

By weight 2.63 : 1

By volume 2 : 1

Overcoating Before overcoating, carry out a solvent wash

and roughen the surface slightly

Standard packaging 180 ml in pre-dosed tubes

Pot life at 23°C N/A

Shelf life max 25°C dry 24 months



T: +32 53 83 86 60

F: +32 53 83 69 88



Industrielaan 8

Zuid III


Belgium

Acotec nv

Pg. 3/6

Date: 16/02/2018

Humidur coatings have the ability to cure under water. The curing of Humidur is a chemical

reaction and is water repellent. The curing times depend on air circulation, temperature and

the film thickness. Humidur is able to cure at sub-zero temperatures.

Curing time

Application

APPLICATION PARAMETERS Humidur FP QR

Temperature before mixing Room temperature

Surface temperature*

Minimum Dew point + 3°C

Maximum 50°C

Humidity*

Relative Humidity < 95%

Surface No condensation

-5°C 5°C 15°C 25°C

Touch-Dry 36 hours 8 hours 6 hours 4 hours

Full cure 10 days 5 days 2 days 24 hours



T: +32 53 83 86 60

F: +32 53 83 69 88



Industrielaan 8

Zuid III


Belgium

Acotec nv

Pg. 4/6

Date: 16/02/2018

SURFACE

PREPARATI-

ON

Cleanliness Methods Roughness Warranty

Minimum St 2 - 3

ISO 8501

Hand tool Power tool (wire

brush, needle gun,

bristle blaster, grind

disk)

Original Profile On request

Optimal Sa 2½

ISO 8501 Gritblasting

60 ± 10 µm 2/3 reference ISO

8503

On request

All surfaces shall be free of oil, grease, dust or any other contamination prior to coating.

* These criteria are valid to achieve the most durable protection. If a reduced coating lifetime is desired, application can

continue outside this window. The existing warranties do not apply in these conditions. Please contact Acotec nv directly

for more information on the expected lifetime in these conditions.

Environment

Humidur FP QR has been designed to fully respect the environment. The product contains:

No VOC (0%) (100 % solids),

No solvents or diluents (WFT = DFT),

No coaltar,

No isocyanates,

No heavy metals.

Humidur FP QR is capable of curing under water without leaching taking place and has no

detrimental effect on the sediment, fauna and flora in and out of the water. When using Hu-

midur FP QR on static marine structures, the biofilm can form itself on top of the Humidur

coating without affecting the substrate and without any loss of the anti-corrosion properties.

As Humidur is a one-layer system, it reduces the amount of waste. Thanks to the pre-dosed

tubes, the waste is minimized as well. All technical reports are available upon request.

Insurance After application, an adhesion test is performed (according to ISO 4624) for which we commit

ourselves to achieve a minimum criterion of 5 MPa.

A corporate warranty can be given under certain conditions. More information upon request.

An insurance policy of 10 years, given by HDI Gerling, is available on all Humidur coatings

and application in case of optimal surface preparation. For the terms and conditions on this

warranty, please contact Acotec nv directly.

Approved in petrochemical industry and offshore oil and gas market by: Shell, Statoil,

ConocoPhilips, Talisman Energy, Maersk Offshore, Transocean Drilling, Fairfield En-

ergy

University Ghent: Approval for resistance against Microbially Induced Corrosion (MIC)

TÜV Rheinland: Approval for combination with cathodic protection systems

Humidur FP Approvals/Certificates



T: +32 53 83 86 60

F: +32 53 83 69 88



Industrielaan 8

Zuid III


Belgium

Acotec nv

Pg. 5/6

Date: 16/02/2018

SGS: Resistance to liquids of Humidur FP QR (EI 1541 + ISO 2812-1)

Force Technology: Fuel and water resistance testing of Humidur FP QR (MIL-PRF

4456F )

Norsok M-501: Rev. 6 June 2013, section n° 7, by SGS

NDT inspections allowed (tested on Talisman Energy assets)

Royal Haskoning: Most cost-effective anti-corrosion solution (Life Cycle Cost Analysis)

Humidur FP Approvals/Certificates



T: +32 53 83 86 60

F: +32 53 83 69 88



Industrielaan 8

Zuid III


Belgium

Acotec nv

Pg. 6/6

Date: 16/02/2018

The English version of the Technical Data Sheet takes precedence over other languages. The

latest version of the Technical Data Sheet can be found on our website www.humidur.be.

Should there be any disrepancies between this document and the document online, the online

document takes precedence.

Important note

Technical Data Sheetcms.condros.eu/Uploads/acotec/FILE_3b7ea79c-c187-43a5-b3f5-6313… · Norsok...

Documents

Transcript of Technical Data Sheetcms.condros.eu/Uploads/acotec/FILE_3b7ea79c-c187-43a5-b3f5-6313… · Norsok...