Team Redundancy Team - OHIO Homepage 2020 | Ohio …Vendor Part # Description Price Quantity Total...
Transcript of Team Redundancy Team - OHIO Homepage 2020 | Ohio …Vendor Part # Description Price Quantity Total...
Team Redundancy Team
Dylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin SmithDylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin SmithDylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin SmithDylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin SmithDylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin SmithDylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin SmithDylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin SmithDylan Andrews. Michael Czubek. Alex Conatser. Jim Ference. Terry Jackson. Jon Martin. Micah McCreery. Kevin Smith
Project RecapFinal Design HighlightsPrototype TestingManufacturing/Assembly Possibilities NISH ReflectionRecommendation for Release
New Ballpoint Pen Assembly Jig Created for ProPoint Employee
Roy’s Limitations Obtained from ProPoint
Roy's Limitations1) Wheelchair-bound2) Muscles are permanently contracted3) Limited use of right arm or hand4) Cannot lean forward or horizontally5) Unable to communicate clearly6) Low endurance7) Low motor skills8) Poor hand-eye coordination9) Trouble grasping objects
Pre-Assembly Area
Solenoid
BatteryDamper
Push-Button
Hand Guide
Handle
Customer Requirements for Pen Assembly Jig Obtained from ProPoint
# Requirement Verification1 No exposed gears, pinch points or fast-moving parts Yes2 High cycle life Yes*3 Simple and safe to load, unload and operate Yes4 Low maintenance Yes5 Fit ProPoint table (1.0 x 0.5 m) Yes6 Low total cost (procurement and operation) Yes7 Increase operator productivity Yes8 Decrease physical stress on operator Yes*9 Able to be operated ambidextrously Yes
*Long-term testing required for verification
Customer Specifications for Pen Assembly Jig Obtained from ProPoint
The Assembly Jig Shall:
# Specification Verification1 Increase Roy's productivity Yes2 Decrease Roy's physical stain Yes3 Not contain any exposed gears or pinch points Yes4 Not exceed the cost of $300 Yes5 Fit on Roy's work station (0.5 x 0.25 m) Yes
Continuous Feedback from ATCO and Roy to Improve Design
Roy Using New Pen Assembly Jig
Mock-Up β-Prototype(Final Design)
α-Prototype
Roy’s ProductivityAssembly time per pen decreased 55%▪ Old Jig: ~11 minutes to assemble 1 pen▪ New Jig: ~5 minutes to assemble 1 penJig set-up time decreased 75%▪ Old Jig: ~4 minutes▪ New Jig: ~1 minute New side clamp
method
Pre-Assembly
Additional Testing Required to Verify:Cycle Life (5 years)Roy’s Physical Strain Reduction▪ Declining as time progressesLong-term Productivity
ATCO Safety StandardsNo exposed gears, pinch points or fast-moving parts
SimplicityEasy for ATCO associates to set up, operate, and maintain
Not designed for mass productionTransferrable Design
Able to be reproduced by ATCO associates using ATCO’s workshop▪ Limited machining or electronics training required▪ All components easily assembled
Vendor Part # Description Price Quantity TotalMcMaster-Carr 7527K44 Terminal Block 4 Circuits $1.43 1 $1.43
McMaster-Carr 7527K59 Jumper for 0.38" Terminal Block $2.15 1 $2.15
McMaster-Carr 7869K131 Flanged Spade Terminal (10 pack) $3.52 1 $3.52
McMaster-Carr 3692K11 Standard Shock Absorber M8 X 0.75" $28.13 1 $28.13
McMaster-Carr 8657K218 Polyethylene LDPE Sheet (0.75"x12"x24") $30.08 1 $30.08
McMaster-Carr 8657K112 Polyethylene LDPE Sheet (0.125"x12"x12") $3.33 1 $3.33
McMaster-Carr 1863A21 Draw Latch Zinc Plated Steel, 1.5" $5.73 2 $11.46
McMaster-Carr 6907K8 Nickel-Plated Brass Liquid-Tight Cord Grip $4.64 1 $4.64
NewarkInOne 74K3604 65mm Mushroom Pushbutton Switch $27.12 1 $27.12
Jameco 262191CB Tubular Solenoid, 24 VDC, 18mm $23.95 1 $23.95
EDMWI.com 21009-CHIG0018 Cordless Drills (24V Rechargeable Battery) $23.08 2 $46.16
Lowes N/A Screws, Adhesives, Fasteners, etc Estimate $10.00
Lowes N/A Junction Box (4"x4"x2") $6.50 2 $13.00
Running Total $204.97
Remaining Balance $128.03
Total CostFuture models able to be manufactured in-house▪ Limited machining or electronics training required▪ All components easily assembled
Purpose of NISH Competition:“To create an assistive technology device/system that addresses employment for people with severe disabilities”
Project Accomplishments:Created a device that addressed employment for person with severe disabilitiesCustomer is NPA employeeDevice is effectiveCustomer is happy
Release to customer for long-term testingVerify Roy’s comfort during extended use of Pen Assembly Jig