TD1204 Datasheet

TD1204

Rev 1.3 (08/14) 1

HIGH-PERFORMANCE, LOW-CURRENT SIGFOX™ GATEWAY AND GPS RECEIVER

Features

SIGFOX Ready™ Gateway and RF transceiver

Frequency range = ISM 868 MHz

Receive sensitivity =-126 dBm

Modulation

• (G)FSK, 4(G)FSK, GMSK

• OOK

Max output power

• +14 dBm

Low active radio power consumption

• 22 µA RX (windowed mode)

• 37 mA TX @ +10 dBm

Multi-GNSS GPS Receiver

Multi-GNSS support

• GPS/GLONASS

• SBAS augmentation services

Ultra-low power consumption

• 22 mA Acquisition

• 15 µA Backup

High Sensitivity

• 56-channel engine

• -162 dBm Tracking

• -148 dBm Cold start

Ultra-low power 3D Accelerometer

Up to ±16g full scale

Board characteristics

Power supply = 2.3 to 3.6 V

2.5 µA idle state consumption

LGA41 (41.91×12.7×3.81mm) Land Grid Array package

Available in several conditioning methods

Applications

SIGFOX™ transceiver (fully certified)

Geolocation and Tracking

Universal Timing and Synchronization

Sensor network

Health monitors

Patents pending

Home security and alarm

Industrial control

Remote control

Vehicles and objects tracking

People and pets geolocation

Pin Assignments

2

1

4

3

6

5

8

7

10

9

11

36

37

34

35

32

33

30

31

28

29

27

40

41

39

GNDReserved

NC

DB3

DB2

SDA

SCL

VDD

NC

GND GND

NC

RST

DAC0

NC

NC

TX

RX

ADC0

TIM2

GND

RF

38

12 VDD

13

14

Reserved

15

17

16

18 19

25

26

24

22 23

20 21

Reserved

GND GND IO_EXT

V_IO

GND

Reserved

42

GPS

Reserved

GND

GND

Reserved

ReservedReserved

ReservedReserved Reserved

Reserved

TD1204

2 Rev 1.3 (08/14)

Disclaimer : The information in this document is provided in connection with Telecom Design products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Telecom Design products.

TELECOM DESIGN ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL TELECOM DESIGN BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF TELECOM DESIGN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Telecom Design makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Telecom Design does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Telecom Design products are not suitable for, and shall not be used in, automotive applications. Telecom Design products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

© 2013-2014 Telecom Design S.A. All rights reserved. Telecom Design®, logo and combinations thereof, are registered trademarks of Telecom Design S.A. SIGFOX™ is a trademark of SigFox S.A. ARM®, the ARM Powered® logo and others are the registered trademarks or trademarks of ARM Ltd. I2C™ is a trademark of Koninklijke Philips Electronics NV. Other terms and product names may be trademarks of other.

TD1204

Rev 1.3 (08/14) 3

Description

Telecom Design’s TD1204 devices are high performance, low current SIGFOX™ gateways, RF transceiver and GPS receiver. The combination of a powerful radio transceiver, a state-of-the-art ARM Cortex M3 baseband processor and a high-efficiency GPS receiver achieves extremely high performance while maintaining ultra-low active and standby current consumption. The TD1204 device offers an outstanding RF sensitivity of –126 dBm while providing an exceptional output power of up to +14 dBm with unmatched TX efficiency. The TD1204 device versatility provides the gateway function from a local Narrow Band ISM network to the long-distance Ultra Narrow Band SIGFOX™ network at no additional cost. Moreover the fully integrated on-board GPS receiver combines outstanding sensitivity with ultra low power which allows you to achieve excellent accuracy and Time-To-First-Fix performance. Combining the SIGFOX™ network possibilities with accurate geolocation will give you access to a brand new world of embedded applications. The TD1204 also embeds an ultra-low power 3D accelerometer with motion and free fall detection to further extend application range. Eventually the broad range of analog and digital interfaces available in the TD1204 module allows any application to interconnect easily to all peripherals. The LVTTL low-energy UART, the I2C bus, the multiple timers with pulse count input/PWM output capabilities, the high-resolution/high-speed ADC and DAC, along with the numerous GPIOs can control any kind of external sensors or activators. Featuring an AES encryption engine and a DMA controller, the powerful 32-bit ARM Cortex-M3 baseband processor can implement highly complex and secure protocols in an efficient environmental and very low consumption way.

TD1204

4 Rev 1.3 (08/14)

GPS

Interface

RF Frontend

Accelerometer

Multiplexer

A/D Converter Control Logic

Charge Amplifier

Interface

Functional Block Diagram

Baseband Processor

26 MHz TCXO

LNA

PA

Logic

Interface ADC

Frac-N PLL

MODEM FIFO

Packet Handler

RF

GPS

VDD

IO_EXT

Debug I/F

ARM Cortex-M3 CPU

I2C GPIO Timer

x2 DAC

32-bit Bus

USART INT ADC AES Watch

dog

Flash 128KB

RAM 16KB

Clock Mgt

Energy Mgt

DMA Ctrl

RS

T

DA

C0

AD

C0

TIM

2

SD

A

SC

L

RX

T

X

32 kHz XTAL

LowPow UART

32 kHz XTAL

26 MHz TCXO

DB

2 D

B3

VD

D

GN

D

X+

Y+

Z+

X-

Z-

Y-

V_I

O

TD1204

SAW Filter

Digital IF Filter

SRAM

32 bit ARM RISC

ROM Code

GNSS engine

Power MGT

Backup RAM

RTC

Integrated LNA

RF Front-end

DC/DC converter

Fractionnal N

synthesizer

RF_GND

TD1204

Rev 1.3 (08/14) 5

TABLE OF CONTENTS

Section Page

1 Electrical Specifications ......................... .......................................................................... 6

1.1 Indicative energy requirements .................... ............................................................................................... 15

1.2 Definition of Test Conditions ..................... .................................................................................................. 16

2 Functional Description ............................ ........................................................................ 17

3 Module Interface .................................. ............................................................................ 19

3.1 Low-Power UART (Universal Asynchronous Receiver/Tra nsmitter) ......................................... .............. 19

3.2 I2C bus ............................................. ............................................................................................................... 19

3.3 Timer/Counter ..................................... ........................................................................................................... 19

3.4 ADC (Analog to Digital Converter) ................. ............................................................................................. 20

3.5 DAC (Digital to Analog Converter) ................. ............................................................................................. 20

3.6 GPIO (General Purpose Input/Output) ............... ......................................................................................... 20

3.7 RST (Reset) ....................................... ............................................................................................................. 21

3.8 Debug ............................................. ................................................................................................................ 21

3.9 RF Antenna ........................................ ............................................................................................................ 21

3.10 GPS Antenna ....................................... .......................................................................................................... 21

3.11 VDD & GND .................................................................................................................................................... 21

4 Bootloader ........................................ ............................................................................... 22

5 Pin Descriptions .................................. ............................................................................ 23

6 Ordering Information .............................. ......................................................................... 25

7 Package Outline ................................... ........................................................................... 26

8 PCB Land Pattern .................................. .......................................................................... 27

9 Soldering Information ............................. ........................................................................ 28

9.1 Solder Stencil .................................... ............................................................................................................ 28

9.2 Reflow soldering profile .......................... ..................................................................................................... 28

TD1204

6 Rev 1.3 (08/14)

1 Electrical Specifications

Table 1. Absolute Maximum Ratings

Parameter Value Units VDD to GND 0 to +3.6 V VIO_EXT to GND -0.5 to +3.6 V Instantaneous VRF-peak to GND on RF Pin -0.3 to +8.0 V Sustained VRF-peak to GND on RF Pin -0.3 to +6.5 V Voltage on Digital Inputs 0 to VDD V Voltage on Analog Inputs 0 to VDD V RX Input Power +10 dBm GPS Input Power +15 dBm Operating Ambient Temperature Range TA -30 to +75 °C Storage Temperature Range TSTG –40 to +125 °C Maximum soldering Temperature 260 °C Note: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at or beyond these ratings in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Power Amplifier may be damaged if switched on without proper load or termination connected. TX matching network design will influence TX VRF-peak on RF pin. Caution: ESD sensitive device.

TD1204

Rev 1.3 (08/14) 7

Table 2. DC Power Supply Characteristics 1

Parameter Symbol Conditions Min Typ Max Units Supply Voltage Range2

VDD 2.3 3.3 3.6 V

GPS Digital I/O Supply Voltage Range

VIO_EXT 1.65 3.3 3.6 V

Output Voltage for GPS antenna and I/O monitoring

VV_IO 0.8VDD 0.95 VDD — V

Output Current for GPS antenna and I/O monitoring

IV_IO — — 6 mA

Power Saving Mode2 ISleep Sleep current using the 32 kHz crystal @ 25°C

1.5 1.8 3.5 µA

Active CPU Mode IActive CPU performing active loop @ 14 MHz 2.55 3.0 3.45 mA Active CPU Mode + RX Mode Current2

IRX — 13 16 mA

Active CPU Mode + TX Mode Current2

ITX_+14 +14 dBm output power, 868 MHz, 3.3 V — 49 — mA ITX_+10 +10 dBm output power, 868 MHz, 3.3 V — 37 — mA

GPS Acquisition IACQ 22 mA GPS Tracking ITRA — 16 — mA GPS Backup IBCKP — 12 — µA GPS Digital I/O Current3

IIO_EXT Tracking — 0.5 — mA

Notes:

1. All specifications guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the “Production Test Conditions” section in “1.1. Definition of Test Conditions” on page 5.

2. Guaranteed by qualification. Qualification test conditions are listed in the “Qualification Test Conditions” section in “1.1. Definition of Test Conditions” on page 14.

3. Using a passive antenna. Please keep in mind that IIO_EXT provides current for active external antenna. IIO can provide enough current to power IIO_EXT if you external active antenna does not require more than 15mA.

TD1204

8 Rev 1.3 (08/14)

Table 3. Transmitter RF Characteristics 1

Parameter Symbol Conditions Min Typ Max Units TX Frequency Range2 FTX 868.0 — 869.7 MHz Modulation Deviation Range3

∆f 868.0-869.7 MHz — 1.5 — MHz

Modulation Deviation Resolution3

FRES 868.0-869.7 MHz — 28.6 — Hz

Frequency Error2 FERR_25 868.0-869.7 MHz, 25°C, 3.3 V — ±2 — kHz FERR_M20 868.0-869.7 MHz, -20°C, 3.3 V — ±3 — kHz FERR_55 868.0-869.7 MHz, 55°C, 3.3 V — ±3 — kHz

Average Conducted Power2

PAVCDP1 -20°C to 55°C, 868.0 MHz to 868.6 MHz, 3.3 V

— — 14 dBm


— — 10 dBm


— — 14 dBm


— — 10 dBm


— — 10 dBm


— — 10 dBm


— — 14 dBm

Transient Power2 PTP 868.0-869.7 MHz, 25°C, 3.3 V, 4800 bps, deviation 2500 Hz, cable loss 0.2 dB,

antenna gain 2 dBi

— — 3 dB

Adjacent Channel Power2

PACP_25 868.0-869.7 MHz, 25°C, 3.3 V, 4800 bps, deviation 2500 Hz, cable loss 0.2 dB,

antenna gain 2 dBi

— -50 — dBm

PACP_M20 868.0-869.7 MHz, -20°C, 3.3 V, 4800 bps, deviation 2500 Hz, cable loss 0.2 dB,

antenna gain 2 dBi

— -51 — dBm

PACP_55 868.0-869.7 MHz, 55°C, 3.3 V, 4800 bps, deviation 2500 Hz, cable loss 0.2 dB,

antenna gain 2 dBi

— -50 — dBm

Spurious Emissions2 POB_TX1 Frequencies < 30 MHz, 868.0-869.7 MHz, 25°C, 3.3 V, 4800 bps, deviation 2500 Hz,

cable loss 0.2 dB, antenna gain 2 dBi

— -82 — dBm

POB_TX2 Frequencies < 1 GHz, 868.0-869.7 MHz, 25°C, 3.3 V, 4800 bps, deviation 2500 Hz,


— -58 — dBm

POB_TX3 Frequencies > 1 GHz, 868.0-869.7 MHz, 25°C, 3.3 V, 4800 bps, deviation 2500 Hz,


— -37 — dBm

Notes: 4. All specifications guaranteed by production test unless otherwise noted. Production test conditions and

max limits are listed in the “Production Test Conditions” section of “1.1. Definition of Test Conditions” on page 5.


6. Guaranteed by component specification.

TD1204

Rev 1.3 (08/14) 9

Table 4. Receiver RF Characteristics 1

Parameter Symbol Conditions Min Typ Max Units RX Frequency Range2 FRX 868.0 — 869.7 MHz Synthesizer Frequency Resolution3

FRES 868.0-869.7 MHz — 28.6 — Hz

Blocking2,4 2MBLOCK Frequency offset ± 2 MHz, 868.0-869.7 MHz, 25°C, 3.3 V

— -38 — dB

10MBLOCK Frequency offset ± 10 MHz, 868.0-869.7 MHz, 25°C, 3.3 V

— -62 — dB

Spurious Emissions2 POB_RX1 From 9 kHz to 1 GHz, 868.0-869.7 MHz, 25°C, 3.3 V

— -84 — dBm

POB_RX2 From 1 GHz to 6 GHz, 868.0-869.7 MHz, 25°C, 3.3 V

— -70 — dBm

RX Sensitivity3 PRX_0.5 (BER < 0.1%) (500 bps, GFSK, BT = 0.5, ∆f = ±250 Hz)

— -126 — dBm

PRX_40 (BER < 0.1%) (40 kbps, GFSK, BT = 0.5, ∆f = ±20 kHz)

— -110 — dBm

PRX_100 (BER < 0.1%) (100 kbps, GFSK, BT = 0.5, ∆f = ±50 kHz)

— -106 — dBm

PRX_125 (BER < 0.1%) (125 kbps, GFSK, BT = 0.5, ∆f = ±62.5

kHz)

— -105 — dBm

PRX_500 (BER < 0.1%) (500 kbps, GFSK, BT = 0.5, ∆f = ±250

kHz)

— -97 — dBm

PRX_9.6 (BER < 0.1%) (9.6 kbps, GFSK, BT = 0.5, ∆f = ±2.4 kHz)

— -110 — dBm

PRX_1M (BER < 0.1%) (1 Mbps, GFSK, BT = 0.5, ∆f = ±1.25 kHz)

— -88 — dBm

PRX_OOK (BER < 0.1%, 4.8 kbps, 350 kHz BW, OOK, PN15 data)

— -109 — dBm

(BER < 0.1%, 40 kbps, 350 kHz BW, OOK, PN15 data)

— -104 — dB

(BER < 0.1%, 120 kbps, 350 kHz BW, OOK, PN15 data)

— -99 — dBm

RSSI Resolution3 RESRSSI — ±0.5 — dB Notes:

1. All specifications guaranteed by production test unless otherwise noted. Production test conditions and max limits are listed in the “Production Test Conditions” section of “1.1. Definition of Test Conditions” on page 5.


3. Guaranteed by component specification. 4. The typical blocking values were obtained while seeking for EN 300-220 Category 2 compliance only.

The typical value specified in the component datasheet are -75 dB and -84 dB at 1 and 8 MHz respectively, with desired reference signal 3 dB above sensitivity, BER = 0.1%, interferer is CW, and desired is modulated with 2.4 kbps, ∆F = 1.2 kHz GFSK with BT = 0.5, RX channel BW = 4.8 kHz. The RF component manufacturer provides a reference design featuring a SAW filter which is EN 300-220 Category 1 compliant. Please contact Telecom Design for more information on EN 300-220 Category 1 compliance.

TD1204

10 Rev 1.3 (08/14)

Table 5. All Digital I/O DC & AC Characteristics 1

Parameter Symbol Conditions Min Typ Max Units Input Low Voltage2 VIOIL — — 0.3VDD V Input High Voltage2 VIOIH 0.7VDD — — V Output High Voltage2 VIOOH Sourcing 6 mA, VDD = 3.0V,

Standard Drive Strength 0.95VDD — — V

Sourcing 20 mA, VDD = 3.0V, High Drive Strength

0.9VDD — — V

Output Low Voltage2 VIOOL Sinking 6 mA, VDD=3.0V, Standard Drive Strength

— — 0.05VDD V

Sinking 20 mA, VDD=3.0V, High Drive Strength

— — 0.1VDD V

Input Leakage Current2

IIOLEAK High Impedance I/O connected to GND or VDD

— — ±25 nA

I/O Pin Pull-Up Resistor2

RPU — 40 — kΩ

I/O Pin Pull-Down Resistor2

RPD — 40 — kΩ

Internal ESD Series Resistor2

RIOESD — 200 — Ω

Pulse Width of Pulses to be Removed by the Glitch Suppression Filter2

tIOGLITCH 10 — 50 ns

Output Fall Time2 tIOOF 0.5 mA Drive Strength and Load Capacitance CL = 12.5 to 25 pF

20+0.1CL — 250 ns

2 mA Drive Strength and Load Capacitance CL = 350 to 600 pF

20+0.1CL — 250 ns

I/O Pin Hysteresis (VIOTHR+ - VIOTHR-)

2 VIOHYST VDD = 2.3 to 3.6 V 0.1VDD — — V




TD1204

Rev 1.3 (08/14) 11

Table 6. ADC DC & AC Characteristics 1

Parameter Symbol Conditions Min Typ Max Units Input Voltage Range2

VADCIN Single Ended 0 — VREF V Differential -VREF/2 — VREF/2 V

Common Mode Input Range2

VADCCMIN 0 — VDD V

Input Current2 IADCIN 2 pF Sampling Capacitors — <100 — nA Analog Input Common Mode Rejection Ratio2

CMRRADC — 65 — dB

Average Active Current2

IADC 10 ksps/s 12 bit, Internal 1.25 V Reference, Warmup Mode = 0

— 67 — µA

10 ksps/s 12 bit, Internal 1.25 V Reference, Warmup Mode = 1

— 63 — µA

10 ksps/s 12 bit, Internal 1.25 V Reference, Warmup Mode = 2

— 64 — µA

Current Consumption of Internal Voltage Reference2

IADCREF — 65 — µA

Input Capacitance2 CADCIN — 2 — pF Input ON Resistance2

RADCIN 1 — — MΩ

Input RC Filter Resistance2

RADCFILT — 10 — kΩ

Input RC Filter/Decoupling Capacitance2

CADCFILT — 250 — fF

ADC Clock Frequency2

fADCCLK — — 13 MHz

Conversion Time2 tADCCONV 6 bit 7 — — ADC CLK

Cycles 10 bit 11 — — ADC

CLK Cycles

12 bit 13 — — ADC CLK

Cycles Acquisition Time2 tADCACQ Programmable 1 — 256 ADC

CLK Cycles

Required Acquisition Time for VDD/3 Reference2

tADCACQVDD3 2 — — µs




TD1204

12 Rev 1.3 (08/14)

Table 7. ADC DC & AC Characteristics 1 (continued)

Parameter Symbol Conditions Min Typ Max Units Startup Time of Reference Generator and ADC Core in NORMAL Mode2

tADCSTART — 5 — µs

Startup Time of Reference Generator and ADC Core in KEEPADCWARM Mode2

— 1 — µs

Offset Voltage2 VADCOFFSET After calibration, single ended — 0.3 — mV After calibration, differential — 0.3 — mV

Thermometer Output Gradient2

TGRADAD

CTH — -1.92 — mV/°C — -6.3 — ADC

Codes/ °C

Differential Non-Linearity (DNL) 2

DNLADC — ±0.7 — LSB

Integral Non-Linearity (INL), End Point Method2

INLADC — ±1.2 — LSB

No Missing Codes2 MCADC 11.9993 12 — bits Gain Error Drift2 GAINED 1.25V Reference — 0.014 0.0335 %/°C

2.25V Reference — 0.014 0.035 %/°C 1.25V Reference — 0.24 0.075 LSB/°

C 2.25V Reference — 0.24 0.625 LSB/°

C Notes:


2. Guaranteed by component specification. 3. On the average every ADC will have one missing code, most likely to appear around 2048 +/- n*512

where n can be a value in the set -3, -2, -1, 1, 2, 3. There will be no missing code around 2048, and in spite of the missing code the ADC will be monotonic at all times so that a response to a slowly increasing input will always be a slowly increasing output. Around the one code that is missing, the neighbor codes will look wider in the DNL plot. The spectra will show spurs on the level of -78dBc for a full scale input for chips that have the missing code issue.

4. Typical numbers given by abs(Mean) / (85 - 25). 5. Max number given by (abs(Mean) + 3x stddev) / (85 - 25).

TD1204

Rev 1.3 (08/14) 13

Table 8. DAC DC & AC Characteristics 1

Parameter Symbol Conditions Min Typ Max Units Output Voltage Range2

VDACOUT VDD voltage reference, Single Ended 0 — VDD V

Output Common Mode Voltage Range2

VDACCM 0 — VDD V

Active Current Including References for 2 Channels 2

IDAC 500 ksps/s 12 bit — 400 — µA 500 ksps/s 12 bit — 200 — µA

100 ksps/s 12 bit NORMAL — 38 — µA

Sample Rate2 SRDAC — — 500 ksps DAC Clock Frequency2

fDAC Continuous Mode — — 1000 kHz Sample/Hold Mode 250 kHz Sample/Off Mode 250 kHz

Clock Cycles per Conversion 2

CYCDACCONV — 2 — DAC CLK

Cycles Conversion Time2 tDACCONV 2 — — µs Settling Time2 tDACSETTLE — 5 — µs Signal to Noise Ratio (SNR)2

SNRDAC 500 ksps, 12 bit, single ended, internal 1.25V reference

— 58 — dB

500 ksps, 12 bit, single ended, internal 2.5V reference

— 59 — dB

Signal to Noise-Pulse Distortion Ratio (SNDR)2

SNDRDAC 500 ksps, 12 bit, single ended, internal 1.25V reference

— 57 — dB


— 54 — dB

Spurious-Free Dynamic Range(SFDR)2

SFDRDAC 500 ksps, 12 bit, single ended, internal 1.25V reference

— 62 — dB


— 56 — dB

Offset Voltage2 VDACOFFSET After calibration, single ended — 2 — mV Differential Non-Linearity2

DNLDAC — ±1 — LSB

Integral Non-Linearity2

INLDAC — ±5 — LSB

No Missing Codes2 MCDAC — 12 — bits Notes:



TD1204

14 Rev 1.3 (08/14)

Table 9. Accelerometer mechanical characteristics

Parameter Symbol Conditions Min Typ Max Units Measurement range FS ±2 — ±16 g Sensitivity So 1 — 12 mg/digit Sensitivity change vs temperature

TCSo FS=±2g — 0.01 — %/°C

Typical zero-g level offset accuracy

TyOff FS=±2g ±40 mg

Zero-g level change vs temperature

TCOff Max delta from 25°C ±0.5 mg/°C

Acceleration noise density

An FS=±2g 220 µg/sqrt(Hz)

Notes:

TD1204

Rev 1.3 (08/14) 15

1.1 Indicative energy requirements The following tables show indicative energy requirements for key-point functionalities of a TD1204 module based on Telecom Design’s software library. All indicated values are for VDD = 3.0V.

Table 10. Indicative energy requirements for SIGFOX ™ and LAN RF Application

Function Conditions Min Typ Max Units Idle state Per hour — 0.0025 — mAh LAN RF Reception Windowed mode, per hour — 0.02 — mAh LAN RF TX+ACK1 — 0.01 — mAh Sigfox™ Transmission Transmission of 12 payload bytes

— 0.083 — mAh

Notes: 1. Includes transmission of 17 payload bytes and reception of an ACK.

Table 11. Indicative energy requirements for GPS ap plication

Function Conditions Min Typ Max Units 3D movement detection Accelerometer 1Hz, per hour — 0.004 — mAh GPS position acquisition1 Cold start fix obtained in 30 seconds — 0.225 — mAh

GPS position acquisition and SIGFOX™ transmission

Accelerometer 1Hz, Cold start fix obtained in 30 seconds

— 0.308 — mAh

Notes: 1. With a 5mA active external GPS antenna. 2. Transmission of longitude, latitude and altitude information.

Table 12. Indicative battery life for typical user case

The following table shows indicative battery life for some typical user-cases based on the TD1204 module.

User case Battery capacity (mAh) 1 Lifetime 1 SIGFOX™ transmission per day2 100 1.8 years

250 4.4 years 500 8 years

1 GPS position acquisition and SIGFOX™ transmission per day3

100 270 days 250 1.8 years 500 3.4 years

Movement detection plus 1 GPS position acquisition and SIGFOX™ transmission per day3

100 246 days 250 1.6 years 500 3.1 years

GPS position acquisition every 10 minutes and position transmission when long-distance movements detected4

500 90 days 1000 180 days 2500 1.2 years

Notes: 1. Assuming a 3V battery with 0.16% discharge per month. 2. With a 12-byte payload and +14dBm output power. 3. Assuming a 30 seconds cold start fix and a 5mA active external GPS antenna. Transmission of longitude,

latitude and altitude information. 4. Assuming a 5 second warm start fix, a 5mA active external GPS antenna and 12 long-distance

movements per day. Transmission of longitude, latitude and altitude information.

TD1204

16 Rev 1.3 (08/14)

1.2 Definition of Test Conditions

1.2.1 Production Test Conditions:

TA = + 25°C

VDD = +3.3 VDC

Production test schematics (unless noted otherwise)

All RF input and output levels referred to the pins of the TD1204 module

1.2.2 Qualification Test Conditions:

TA = -30 to +75°C (Typical TA = 25°C)

VDD = +2.3 to 3.6 VDC (Typical VDD = 3.3 VDC)

Using TX/RX Split Antenna reference design or production test schematic

All RF input and output levels referred to the pins of the TD1204 module

TD1204

Rev 1.3 (08/14) 17

2 Functional Description

The TD1204 devices are high-performance, low-current, wireless SIGFOX™ gateways, RF transceiver, GPS receiver and accelerometer. The wide operating voltage range of 2.3–3.6 V and low current consumption make the TD1204 an ideal solution for battery powered applications.

The TD1204 operates as a time division duplexing (TDD) transceiver where the device alternately transmits and receives data packets. The device uses a single-conversion mixer to downconvert the 2-level FSK/GFSK or OOK/ASK modulated receive signal to a low IF frequency. Following a programmable gain amplifier (PGA) the signal is converted to the digital domain by a high performance ∆Σ ADC allowing filtering, demodulation, slicing, and packet handling to be performed in the built-in DSP increasing the receiver’s performance and flexibility versus analog based architectures. The demodulated signal is output to the baseband CPU by reading the 64-byte RX FIFO.

A single high precision local oscillator (LO) is used for both transmit and receive modes since the transmitter and receiver do not operate at the same time. The LO is generated by an integrated VCO and ∆Σ Fractional-N PLL synthesizer. The synthesizer is designed to support configurable data rates from 0.123 kbps to 1 Mbps. The TD1204 operates in the frequency bands of 868.0–869.7 MHz with a maximum frequency accuracy step size of 28.6 Hz. The transmit FSK data is modulated directly into the ∆Σ data stream and can be shaped by a Gaussian low-pass filter to reduce unwanted spectral content.

The power amplifier (PA) supports output power up to +14 dBm with very high efficiency, consuming only 37 mA at +10 dBm. The integrated power amplifier can also be used to compensate for the reduced performance of a lower cost, lower performance antenna or antenna with size constraints due to a small form-factor. The PA is single-ended to allow for easy antenna matching and low BOM cost. The PA incorporates automatic ramp-up and ramp-down control to reduce unwanted spectral spreading. A highly configurable packet handler allows for autonomous encoding/decoding of nearly any packet structure.

As both the local Narrow Band ISM network and the long-distance Ultra Narrow Band SIGFOX™ network can be addressed seamlessly, the TD1204 device provides a natural gateway function at no additional cost. Thus, the same TD1204 module can be used both for local RF communication with peer modules, and also connect to the wide-area SIGFOX™ RF network.

The broad range of analog and digital interfaces available in the TD1204 module allows any application to interconnect easily to the SIGFOX™ network. The LVTTL low-energy UART, the I2C bus, the multiple timers with pulse count input/PWM output capabilities, the high-resolution/high-speed ADC and DAC, along with the numerous GPIOs can control any kind of external sensors or activators. Featuring an AES encryption engine and a DMA controller, the powerful 32-bit ARM Cortex-M3 baseband processor can implement highly complex and secure protocols in an efficient environmental and very low consumption way. This unique combination of a powerful 32-bit ARM Cortex-M3 CPU including innovative low energy techniques, short wake-up time from energy saving modes, and a wide selection of intelligent peripherals allows any application to connect to the SIGFOX™ network.

The application shown in Figure 1 shows the minimum interconnection required to operate the TD1204 module.

Basically, only the 7 GND, 2 RF_GND, VDD, V_IO, IO_EXT, TX, RX and RF antenna pin connections are necessary. The RST (reset) pin connection is not mandatory and this pin can be left floating if not used.

A 10 µF/6.3V decoupling capacitor must be added as close as possible to the VDD on pin 9.

A 4.7 µF/6.3V decoupling capacitor must be added as close as possible to the VDD on pin 12.

A 1.0 µF/6.3V decoupling capacitor must be added as close as possible to IO_EXT.

The TX/RX pins are LVTTL-compatible and feature internal pull-up resistors.

TD1204

18 Rev 1.3 (08/14)

A 50 Ω matched RF antenna must be connected to the RF pin, with a low-capacitance (< 0.5 pF) TVS diode to protect the RF input from ESD transients.

An external active GPS antenna must be connected to the U.FL connector (reference U.FL-R-SMT-1 from Hirose) on top of the PCB. The antenna will be powered by the power supply connected to IO_EXT through the U.FL connector. Supported U.FL connector sizes are 1.9mm or 2.4mm. A typical application should use an external active antenna requiring less than 15mA to be powered. Otherwise please contact Telecom Design for a reference design.

The connection of a super-blue LED with series current-limiting resistor of 220 Ω on pin TIM2 is recommended in order to display the bootloader status at boot time.

Note: The TVS diode used for protecting the RF input against ESD must be of low-capacitance (0.5 pF typical) type, e.g. ESD9R3.3ST5G (On Semiconductor), for example.

TD

1204

2

1

4

3

6

5

8

7

10

9

11

36

37

34

35

32

33

30

31

28

29

27

24

25

38

GND

Reserved

Reserved

NC

DB3

DB2

SDA

SCL

VDD

NC

GND GND

NC

RST

DAC0

NC

NC

TX

RX

ADC0

TIM2

GND

RF_GND

RF

RF_GND

TX

RX

VDD

C1 10 µF/6V3

50Ω Antenna

220 Ω

Blue LED

Recommended for Bootloader status display

Figure 1. Typical Application

13

12

15

14

17

16

19

18

25

26

23

24

21

22

20

VDD

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

GND

GND

IO_EXT

V_IO

GND

Reserved 37

C2 4.7 µF/6V3

42

GPS

Active GPS Antenna C3 1 µF/6V3

TVS Diode

TD1204

Rev 1.3 (08/14) 19

3 Module Interface

3.1 Low-Power UART (Universal Asynchronous Receiver /Transmitter) The TD1204 communicates with the host MCU over a standard asynchronous serial interface consisting of only 2 pins: TX and RX. The TX pin is used to send data from the TD1204 module to the host MCU, and the RX pin is used to receive data into the TD1204 module coming from the host MCU.

This interface allows two-way UART communication to be performed in low energy modes, using only a few µA during active communication and only 150 nA when waiting for incoming data.

This serial interface is designed to operate using the following serial protocol parameters:

LVTTL electrical level

9600 bps

8 data bits

1 stop bit

No parity

No hardware/software flow control

This interface operates using LVTTL signal levels to satisfy the common interface to a low power host MCU. If an EIA RS232-compliant interface voltage level is required, an RS232 level translator circuit must be used. It is also possible to use a common USB/UART interface chip to connect to an USB bus.

Over this serial interface, the TD1204 device provides a standard Hayes “AT” command set used to control the module using ASCII readable commands and get answers, as well as to send or receive data.

The list of available commands with their corresponding arguments and return values, a description of their operation and some examples are detailed into the “TD1204 Reference Manual”.

3.2 I2C bus As a convenience, the TD1204 module is equipped with a popular I2C serial bus controller that enables communication with a number of external devices using only two I/O pins: SCL and SDA. The SCL pin is used to interface with the I2C clock signal, and the SDA pin to the I2C data signal, respectively. When not used for I2C bus, these 2 pins can be configured to perform other functions using “AT” configuration commands, please refer to the “TD1204 Reference Manual” for details.

The TD1204 module is capable of acting as both a master and a slave, and supports multi-master buses. Both standard-mode (Sm), fast-mode (Fm) and fast-mode plus (Fm+) speeds are supported, allowing transmission rates all the way from 10 kbit/s up to 1 Mbit/s. Slave arbitration and timeouts are also provided to allow implementation of an SMBus compliant system. Both 7-bit and 10-bit addresses are supported, along with extensive error handling capabilities (clock low/high timeouts, arbitration lost, bus error detection).

The operation of this interface is controlled by the mean of Hayes “AT” commands sent over the UART interface. To obtain a list of the available commands with their corresponding arguments and return values, a description of their operation and some examples, please refer to the “TD1204 Reference Manual”.

3.3 Timer/Counter The TD1204 provides an interface to an integrated timer/counter using the TIM2 pin. This pin can be configured as either a capture input or a compare/PWM output to the 16-bit internal timer/counter. When not used for timer/counter operation, this pin can be configured to perform other functions using “AT” configuration commands, please refer to the “TD1204 Reference Manual” for details.

TD1204

20 Rev 1.3 (08/14)

The timer consists in a counter that can be configured to up-count, down-count, up/down-count (continuous or one-shot).

The timer also contains 2 output channels, that can be configured as either an output compare or single/double slope PWM (Pulse-Width Modulation) outputs routed to the TIM2 pin.


3.4 ADC (Analog to Digital Converter) The TD1204 provides an interface to an integrated low-power SAR (Successive Approximation Register) ADC, capable of a resolution of up to 12 bits at up to 1 Msps or 6 bits at up to 1.86 Msps. The ADC0 pin provides the external interface to the ADC. When not used for ADC operation, this pin can be configured to perform other functions using “AT” configuration commands, please refer to the “TD1204 Reference Manual” for details.

Along with the ADC0 analog input channel, the ADC also provides an internal temperature, VDD, and GND input channel that may be used to get a digital representation of analog temperature or voltage values. It is also possible to loopback the analog output of the integrated DAC (see section 3.5, “DAC (Digital to Analog Converter)”).

The internal ADC provides an optional input filter consisting of an internal low-pass RC filter or simple internal decoupling capacitor. The resistance and capacitance values are given in the electrical characteristics for the device, named RADCFILT and CADCFILT respectively.

The reference voltage used by the ADC can be selected from several sources, including a 1.25 V internal bandgap, a 2.5 V internal bandgap, VDD, a 5 V internal differential bandgap or unbuffered 2VDD.

Additionally, to achieve higher accuracy, hardware oversampling can be enabled. With oversampling, each selected input is sampled a number of times, and the results are filtered by a first order accumulate and dump filter to form the end result. Using 16x oversampling minimum, it is thus possible to achieve result resolution of upt to 16 bits.


3.5 DAC (Digital to Analog Converter) The TD1204 provides an interface to an integrated DAC that can convert a digital value to a fully rail-to-rail analog output voltage with 12-bit resolution at up to 500 ksps. The DAC may be used for a number of different applications such as sensor interfaces or sound output. The analog DAC output is routed to the DAC0 pin. When not used for ADC operation, this pin can be configured to perform other functions using “AT” configuration commands, please refer to the “TD1204 Reference Manual” for details.

The reference voltage used by the DAC can be selected from several sources, including a 1.25 V internal bandgap, a 2.5 V internal bandgap, or VDD.

The internal DAC provides support for offset and gain calibration, and contains an automatic sine generation mode as well as a loopback output to the ADC (see section 3.4, “ADC (Analog to Digital Converter)”).

3.6 GPIO (General Purpose Input/Output) Apart from the TX and RX UART pins, and the RF pins, all signal pins are available as general-purpose inputs/outputs. This includes the ADC0, TIM2, DAC0, SCL, SDA, DB2, DB3 pins when not used for their main function. This configuration can be performed using “AT” commands, please refer to the “TD1204 Reference Manual” for details.

TD1204

Rev 1.3 (08/14) 21

All the ADC0, TIM2, DAC0, SCL, SDA, DB2, DB3 pins can be configured individually as tristate (default reset state), push-pull, open-drain, with/without pull-up or pull-down resistor, and with a programmable drive strength (0.5 mA/2 mA/6 mA/20 mA).

When configured as inputs, these pins feature an optional glitch suppression filter and full (rising, falling or both edges) interrupt with wake-up from low-power mode capabilities. Of course, the pin configuration is retained even when using these low-power modes.

The operation of the GPIOs is controlled by the mean of Hayes “AT” commands sent over the UART interface. To obtain a list of the available commands with their corresponding arguments and return values, a description of their operation and some examples, please refer to the “TD1204 Reference Manual”.

3.7 RST (Reset) The TD1204 module features an active-low RST pin. This pin is held high by an internal pull-up resistor, so when not used, this pin can be left floating.

3.8 Debug The TD1204 module devices include hardware debug support through a 2-pin serial-wire debug interface. The 2 pins DB2 and DB3 are used for this purpose. The DB2 pin is the ARM Cortex-M3’s SWDIO Serial Wire data Input/Output. This pin is enabled after a reset and has a built in pull-up. The DB3 pin is the ARM Cortex-M3’s SWCLK Serial Wire Clock input. This pin is enabled after reset and has a built-in pull down. When not used for debug operation, these 2 pins can be configured to perform other functions using “AT” configuration commands, please refer to the “TD1204 Reference Manual” for details.

Although the ARM Cortex-M3 supports advanced debugging features, the TD1204 devices only use two port pins for debugging or programming. The systems internal and external state can be examined with debug extensions supporting instruction or data access break- and watch points.

For more information on how to enable the debug pin outputs/inputs the reader is referred to Section 28.3.4.1 (p. 457), the ARM Cortex-M3 Technical Reference Manual and the ARM CoreSight™ Technical Reference Manual.

3.9 RF Antenna The TD1204 support a single-ended RF pin with 50 Ω characteristic impedance for connecting a matched-impedance external antenna. This pin is physically surrounded by 2 RF GND pins for better noise immunity.

3.10 GPS Antenna The TD1204 support a 1.9mm or 2.4mm U.FL RF connector on top of PCB for connecting an external active antenna. Power supply for active antenna is provided through IO_EXT. If your external active antenna does not require more than 15mA you can use V_IO to power-up IO_EXT. Otherwise please use an external regulator to provide current supply for IO_EXT and connect V_IO to the regulator’s Chip Enable.

3.11 VDD & GND The TD1204 provides 8 GND pins and 2 RF_GND pins: all of them must be connected to a good ground plane.

A 10 µF/6.3 V decoupling capacitor should be placed as closed as possible to the VDD on pin 9.

A 4.7 µF/6.3 V decoupling capacitor should be placed as closed as possible to the VDD on pin 12.

TD1204

22 Rev 1.3 (08/14)

4 Bootloader

The TD1204 module contains an integrated bootloader which allows reflashing the module firmware either over the RX/TX UART connection, or over the air using the built-in RF transceiver.

The bootloader is automatically activated upon module reset. Once activated, the bootloader will monitor the UART/RF activity for a 200 ms period, and detect an incoming update condition.

If the update condition is met, the TD1204 will automatically proceed to flash the new firmware with safe retry mechanisms, or falls back to normal operation.

TD1204

Rev 1.3 (08/14) 23

5 Pin Descriptions

Pin Pin Name I/O Description

1 GND GND Connect to PCB ground

2 Reserved I/O Reserved pin – Do not connect


4 NC NC Not connected

5 DB3 I

SWDCLK (SWD Clock) Signal This signal provides the SWD clock signal to the integrated TD1204 ARM® CPU. This pin may be configured to perform various functions.

6 DB2 I/O

SWDIO (SWD Data I/O) Signal This signal provides the SWD programming/debugging signal interface to the integrated TD1204 ARM® CPU. This pin may be configured to perform various functions.

7 SDA I/O General Purpose Low -Power Digital I/O This pin may be configured to perform various functions, including the I2C DATA (SDA) function.

8 SCL I/O General Purpose Low -Power Digital I/O This pin may be configured to perform various functions, including the I2C clock (SCL) function.

9 VDD VDD +2.3 to +3.6 V Supply Voltage Input The recommended VDD supply voltage is +3.3V. Connect a 10 µF capacitor as close as possible to this input.

10 NC NC Not connected


12 VDD VDD +1.65 to +3.6 V GPS Supply Voltage Input The recommended VDD supply voltage is +3.3V. Connect a 4.7 µF capacitor as close as possible to this input.


2

1

4

3

6

5

8

7

10

9

11

36

37

34

35

32

33

30

31

28

29

27

40

41

39

GND

Reserved

NC

DB3

DB2

SDA

SCL

VDD

NC

GND GND

NC

RST

DAC0

NC

NC

TX

RX

ADC0

TIM2

GND

RF

38

12 VDD

13

14

Reserved

15

17

16

18 19

25

26

24

22 23

20 21

Reserved

GND GND IO_EXT

V_IO

GND

Reserved

42

GPS

Reserved

GND

GND

Reserved

ReservedReserved

ReservedReservedReserved

Reserved

TD1204

24 Rev 1.3 (08/14)











24 IO_EXT

+1.65 to +3.6 V GPS Digital I/O and Antenna Supply Voltage Input Connect a 1.0 µF capacitor as close as possible to this input. Drive with V_IO if your external active antenna requires less than 15mA. Otherwise drive with appropriate hardware.

25 V_IO O GPS Digital I/O Supply Voltage Output



28 NC NC Reserved pin – Do not connect

29 RST I

Active Low RESET input signal This signal resets the TD1204 module to its initial state. If not used, this signal can be left floating, as it is internally pulled up by an integrated resistor.

30 DAC0 I/O General Purpose Low -Power Digital I/O This pin may be configured to perform various functions, including the DAC analog output #0 function.



33 TX O

Low -Power UART Data Transmit Signal This signal provides the UART data going from the TD1204 module out to the host application processor. This signal is internally pulled up by an integrated resistor.

34 RX I

Low -Power UART Data Receive Signal This signal provides the UART data coming from the host application processor going to the TD1204 module. This signal is internally pulled up by an integrated resistor.

35 ADC0 I/O General Purpose Low -Power Digital I/O This pin may be configured to perform various functions, including the ADC input #6 function.

36 TIM2 I/O General Purpose Low -Power Digital I/O This pin may be configured to perform various functions, including the timer input capture / output compare #2 function.


38 Reserved Reserved pin – Do not connect

39 RF_GND GND Connect to PCB ground

40 RF RF 50 Ω RF Antenna Connection

41 RF_GND GND Connect to PCB ground

42 GPS GPS

U.FL GPS Antenna Connector (on top) Please see reference U.FL-R-SMT-1 from Hirose for more information about compatible coaxial cable. This connector provides power supply to the external active antenna.

TD1204

Rev 1.3 (08/14) 25

6 Ordering Information

Part Number Description Package Type Operating Temperature

TD1204 ISM SIGFOX™ gateway 128K Flash/16KRAM

TCXO LGA41 Pb-free

-30° to +75°C

The TD1204 ISM SIGFOX™ gateway module is available in several conditionings.

Please contact Telecom Design for more information.

TD1204

26 Rev 1.3 (08/14)

7 Package Outline

Figure 2 illustrates the package details for the TD1204.

Figure 2. 41-Pin Land Grid Array (LGA)

Notes :

1. All dimensions are shown in millimeters (mm) unless otherwise noted.

Bottom View

Top View

TD1204

Rev 1.3 (08/14) 27

8 PCB Land Pattern

Figure 3 illustrates the PCB land pattern details for the TD1204. (This footprint is also compatible with the TD1202).

Figure 3. PCB Land Pattern

Notes :

1. All dimensions are shown in millimeters (mm) unless otherwise noted.

TD1204

28 Rev 1.3 (08/14)

9 Soldering Information

9.1 Solder Stencil The TD1204 module is designed for RoHS reflow process surface mounting.

For proper module assembly, the solder paste must be applied on the receiving PCB using a metallic stencil with a recommended 0.150 µm thickness.

9.2 Reflow soldering profile The recommendation for lead-free solder reflow from IPC/JEDEC J-STD-020D Standard should be followed.

Below are typical reflow soldering profiles for a medium-size board:

Setpoints 1 2 3 4 5 6 7 8 9 Top (°C) 145 155 165 175 185 195 230 250 250 Bottom (°C) 145 155 165 175 185 195 230 250 250 Notes: Conveyor Speed is 65.00 cm / min

Figure 4 - Reflow Soldering Profile

Run Preheat (s) 40-130°C

Soak Time (s) 130-217°C

Reflow Time (s) / 217°C

Peak Temp (°C)

Slope1 (°C / s) (40-130°C)

Slope2 (°C / s) (250-150°C)

2 56.04 122.40 58.66 239.00 1.53 -2.78 3 56.93 123.72 59.45 243.93 1.56 -2.79 4 55.34 124.25 57.34 239.45 1.54 -2.87 5 55.92 122.53 61.46 244.00 1.57 -2.77 6 58.12 123.38 57.89 239.84 1.53 -2.73

For more information on reflow soldering process profiling, please visit the http://kicthermal.com/ website.

0 50 100 150 200 250 300 350

Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9

50

100

150

200

Time (seconds)

Tem

pera

ture

(°C

)

TD1204

Rev 1.3 (08/14) 29

DOCUMENT CHANGE L IST

Revision 0.5

Draft

Revision 0.6

Changed contact information

Revision 0.7

Corrected number of available ADCs and ADC0 pin ADC input number

Revision 0.8

Removed USRx GPIO pins from the GPIO description section

Revision 1.0

First Release. Corrected external GPS antenna maximum current requirement for standard design.

Revision 1.1

Corrected wrong pin name and function for PIN 2 which should be left unconnected.

Revision 1.2

Added soldering information.

Revision 1.3

Added TVS diode to antenna

Changed contact information

TD1204

30 Rev 1.3 (08/14)

NOTES:

TD1204

Rev 1.3 (08/14) 31

NOTES:

TD1204

32 Rev 1.3 (08/14)

CONTACT INFORMATION

Telecom Design S.A.

Zone Actipolis II — 2 bis rue Nully de Harcourt 33610 CANEJAN, France Tel: +33 5 57 35 63 70 Fax: +33 5 57 35 63 71

Please visit the Telecom Design web page: http://www.telecomdesign.fr/

The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Telecom Design assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Telecom Design assumes no responsibility for the functioning of undescribed features or parameters. Telecom Design reserves the right to make changes without further notice. Telecom Design makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Telecom Design assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Telecom Design products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Telecom Design product could create a situation where personal injury or death may occur. Should Buyer purchase or use Telecom Design products for any such unintended or unauthorized application, Buyer shall indemnify and hold Telecom Design harmless against all claims and damages.

Telecom Design is a trademark of Telecom Design S.A. SIGFOX™ is a trademark of SigFox S.A. Other products or brand names mentioned herein are trademarks or registered trademarks of their respective holders.

TD1204 Datasheet

Documents

Transcript of TD1204 Datasheet