TAGA Engineering Software Ltd
Transcript of TAGA Engineering Software Ltd
- TSLOPE
TAGA Engineering Software Ltd
TSLOPE Presentation
April 8, 2021
Department of Mineral Resources EngineeringUniversity of Western Macedonia
- TSLOPE
Presentation outline
Introduction
A short history
Slope stability analysis - discussion
TSLOPE
Three examples
Concluding remarks
- TSLOPE
Complexity of failure mechanisms
5 |
Stead, Eberhardt & Coggan 2006 Developments in the characterization of complex rock slope
deformation and failure using numerical modelling techniques. Engineering Geology 83 (2006) 217– 235
- TSLOPE
Who we are
TSLOPE development by small team led by Peter Wood,
Wellington (New Zealand)
Technical direction from Dr Ian Brown (Wellington) and
Professor Nicholas Sitar (University of California,
Berkeley)
Web based delivery of software and support
Web site www.tagasoft.com
- TSLOPE
TSLOPE history
• 1989 first 3D analysis program developed for design of
Puente Hills landfill (Southern California), using LA
County method of force equilibrium.
• 2009 Spencer’s method extended to 3D.
• 2016 fully integrated 2D and 3D analysis using the same
geotechnical model.
- TSLOPE
Why have we developed yet another slope stability
program?
• The world is 3D and so is TSLOPE
• Our integration of 3D and 2D analysis is unique
• We can provide a cost effective solution using SaaS
• We have no defaults or artificially imposed restrictions on
slide surface geometry
• “you must always check against another program” Steve
Wright (2013 Seed Lecture)
- TSLOPE
Why do we carry out slope stability analyses ?
• To get a numerical value that we can assign to the
stability (or otherwise) of a slope – the factor of safety.
• To confirm something we already know – the slope is
stable, or it is unstable.
• To back calculate the material strength following
observed slope failure.
• To satisfy a regulatory requirement eg. factor of safety
greater than 1.5.
• To provide insight into slope behaviour.
• To assist with slope design – excavation geometry,
drainage, reinforcement
- TSLOPE
Why do we continue to use 2D limit equilibrium slope stability analysis ?
• There is a long history of use.
• Slope geometry does not vary in the direction perpendicular to the cross section analysed.
• Few acceptable 3D programs; they generally use simplified assumptions that limit applicability to real problems.
• Alternative numerical methods are complex and require material properties that are difficult to measure or estimate.
- TSLOPE
Why we should carry out 3D slope stability analyses
• We now work in a 3D world with most other computer
applications (GIS, CAD, geological modelling, mine
planning).
• 3D geometry often has significant influence on slope
stability, e.g. wedge like geometry or bottle mouth
canyons.
• 3D slope data becoming increasingly easy to acquire
(e.g. laser scanning) and use.
• All this leads to a better understanding of the nature of
slope failure mechanisms.
- TSLOPE
TSLOPE highlights
• TSLOPE - a program for 2D and 3D slope stability
analysis; from wedge failures in open pit mines defined
by rock structure, to landfills where failure is possible
along a geofabric liner.
• Ordinary Method of Columns allows for evaluation of 3D
effects, provides for calculation of local factors of safety
which indicate the possibility of progressive failure.
• Implementation of Spencer’s method in 3D provides a
way of checking and comparing with previous results
using methods that fully satisfy equilibrium.
- TSLOPE
3D Ordinary Method of Columns
• Calculates overall factor of safety as ratio of sum of resisting forces over sum of driving forces.
• Always get a solution – there are no iteration or convergence issues.
• Used as starting point for Spencer’s analysis.
• Automatically get local factors of safety for individual columns.
• Local factors of safety provide an indication of the potential for progressive failure.
- TSLOPE
3D Spencer’s analysis method details
• Use minimization to determine best estimate for global equilibrium, including sliding direction.
• For symmetric problems, achieving “exact” global equilibrium is often possible.
• For asymmetric problems, typically get within a few percent of “exact” global equilibrium.
• Method is robust. It also calculates out of balance forces and moments, thus providing estimate for “error” of the result.
• Always get a solution – we don’t have an error message “algorithm failed to converge”.
- TSLOPE
Slope model definition
• Multiple surfaces can be input.
• Complex slope geology accommodated with layers or zones.
• Geology independent of topography and excavation surfaces.
• Slope failure surfaces pre-defined, arbitrary 3D shapes, or complex surfaces developed constrained by layers.
• Groundwater as phreatic surfaces, or pore pressure surfaces.
• 2D sections automatically extruded to 3D.
• Import and drape geo-referenced images.
• Tension crack outlines to constrain failure.
• Rock reinforcement – anchors.
- TSLOPE
Geological model developed using Leapfrog3D
Field geology sketch draped on open pit topography; surface trace
of faults located in x,y,z with structural markers
- TSLOPE
Geological model exported from Leapfrog3D
Fault planes modelled, then combined to give a continuous failure surface
- TSLOPE
Why we carry out back analysis
• The process of determining the conditions and establishing a suitable model of the slope from a failure is known as back-analysis (or back-calculation)
• When a slope fails by sliding it can provide a useful source of information on the conditions in the slope at the time of failure
• A slope failure provides an opportunity to validate stability analysis methods
• Factor of safety at time of failure is 1.0
- TSLOPE
2D or not 2D – that is, 3D
• Traditionally slope stability analyses have been conducted using two dimensional cross sections, if only because in the early days of geotechnical engineering such analyses were done by hand and three dimensional analyses were unthinkable.
• With modern computers, anything is possible. The big question is does it make a difference?
• The answer is YES, it can. The factor of safety for a three dimensional sliding surface can be less than or greater than a two dimensional one by up to 50 percent. If you don’t check the effect of 3D, you don’t know!
- TSLOPE
Concluding remarks
• TSLOPE allows workflow for slope stability studies to be simplified
• Direct use of datasets from UAV, laser scanning
• No re-entry or re-formatting of geological data
• Back calculation option to learn from slope failures
• All limit equilibrium analyses (2D, 3D, wedge, planar) in the one program
• TSLOPE licensing on a time basis
• We look forward to supporting your academic licences
www.tagasoft.com