Model No.: T11

T11 Starlight Mini-PIR Camera

User Manual

Table of Contents

Part 1 Before First Use ..............................1-2

Part 2 Quick Guide .......................................3

Part 3 Detailed User Manual .....................4-20

Part 3 Detailed User Manual

Safety Precautions ....................................... .4

Warning on Invasion of Privacy ....................... 5

What’s Included ............................................ 6

T11 Diagram ................................................ .7

Before Using Your Conbrov T11 Camera . . . . .8-11

How to Use Your Conbrov T11 Camera ......12-14

1. Turning the Camera On/Off .....................12

2. How to Record a Video ......................12-13

3. How to Switch Into Night Vision ..............14

4.How to Play the Video ...........................14

LED Status ..................................................15

Technical Specifications ...............................16

FAQs .....................................................17-19

Warranty .....................................................20

Disposal ......................................................20

Declaration of conformity ..............................20

Part1 Before First Use

Charging the cameraBefore the first use, charge the camera for about 3 to 4 hours via your PC or USB charger (power adapter should be no more than "5V/1A").

Formatting the microSD cardBefore the first use, format the micro SD card to FAT32 format (applicable to Windows system ONLY). The camera only supports class 10 micro SD cards with at least an 8GB capacity. It supports cards up to 32 GB.

Yellow indicator

1

Yellow indicator

Part1: Before First Use

Resetting the cameraIf the camera malfunctions for any reason, reset it with the included pin. A small paperclip can also be used.

2

Part 2 Quick Guide

A.Install the microSD Card B.Turn On/Off

C.Record A Video D.Play The Video

OFF LED flashes red and blue alternately and then turns off

Record a Video

1

2

USB2.0

For more detailed information, see Part 3: Detailed User Manual, please turn to Page 8.

ON blue LED stays on and the camera is in standby mode

2S power on

3

2S

2S

LED flashes blue 3 times then goesoff

4

Safety Precautions

Read this instruction manual carefully before using the camera. It contains important information for your safety as well as operating and maintenance instructions.Follow all safety precautions in order to prevent damage due to improper use of the camera.Keep this user manual carefully for future use. Should this camera be passed along to a third party, this user manual must be handed on as well.Use the camera only for its intended purpose.In the event of improper use or erroneous handling, no liability can be assumed for any possible damage which may occur.Never try to repair the camera yourself. Only allow qualified personnel to repair the camera in the event of malfunctions.Warning! The camera is not waterproof. Never immerse the camera in water or other liquids while cleaning or operating it. Do not open the housing under any circumstances. Do not introduce any metal objects into the interior of the housing.Never use accessories which are not recommended by the manufacturer.Keep the camera away from all hot surfaces and naked flames. Protect the camera from extreme heat and cold, dust, direct sunlight, humidity and drops or jets of water.Do not place any heavy objects on the camera.The manufacturer is not responsible for any missing video data due to maloperation, micro SD card malfunctions, camera angle limitation, etc.

5

Warning on Invasion of Privacy

The camera should be used for legal purpose only. Follow the laws of your country.Recording and circulating an image of an individualmay constitute an infringement of their privacy for which you could be liable. Ask for authorization before filming individuals, particularly if you want to keep your recordings and/or circulate images on the Internet or any other medium. Do not circulate a degrading image or one which could undermine the reputation or dignity of anindividual.

Model No.: T11

T11 Starlight Mini-PIR Camera

User Manual

What's Included

USB cable Camera Manual

Pin

6

T11 Diagram

7

PIR motion detectionManually record

Power

Audio on/off

PIR USB

micro SD

Lens

6pcs invisible LED light

Reset

Installing the microSD card Removing the micro SD card

Before Using Your Conbrov T11 Camera

1. Charging your camera

(1) The camera power must be off before charging.(2) Plug the USB cable both in the camera and in a computer USB port or a 5V/1A adaptor (not included). The yellow LED is on while charging. The charge time is about 3to 4hours.(3) The yellow LED turns off when the camera is fully charged.

8

Yellow indicator Off

Steady yellow

Off

Flashing blue and red

Charging

Fully charged

Low power

2. Installing the microSD card

Before Using Your Conbrov T11 Camera

9

Caution! Format the micro SD before use. Doing this, however, will remove all data from the card. Make sure to back up any data before formatting (applicable to Windows system ONLY).

The Camera records video only when micro SD is installed.

(1) The device supports a Class 10 micro SD card which has capacity of more than 8GB and up to32GB.(2) Do not remove the micro SD card during operation. It will damage both the memory card and camera.(3) Push the micro SD card into the slot gently until it clicks into place. The card only fits one way, so do not force the card into the port.(4) To remove the micro SD card, make sure the camera is OFF. Press down on the micro SD and it will pop up, you can then pull it out easily.

New

Open

Save

Save as

Page settings

Print

Exit

File Edit Format View Help

SETTIME.TXT

SETTIME

Before Using Your Conbrov T11 Camera

3.Setting the date and timeTurn on the camera first and connect it to PC with the included USB cable, after about 12 seconds, the disc icon will appear on your computer, then please open SETTIME.TXTNote:Please record a video first before setting the date and time.

Open the SETTIME.TXT file,The following menu will be displayed:

SETTIME.TXT

file Edit Format View Help

2016-07-15,23:59:59

yes

yyyy-mm-dd, hh:mm:ss

yes: loop recording on microSDno: no loop recording

Time format: File name

Modify the date and time on the computer. After setting date and time, click on “File” and then on “Save”.

10

Before Using Your Conbrov T11 Camera

Note: If you cannot find the file SETTIME.TXT after opening the microSD on the computer, please record a video clip to activate the card and set the date and time again. The date and time will remain accurate unless the battery has been depleted for longtime.

11

How to Use Your Conbrov T11 Camera

1. Turning the Camera On/Off

(1) Press and hold the to switch the camera on. The LED will flash blue, which indicates that it is in standby mode.(2) Press and hold the to switch the camera off. The LED will flash red and blue alternately and then turn off.

ON LED flashes blue and the camera is in standby mode

OFF LED flashes red and blue alternately and then turns off

Note: If the camera switches off automatically, there are two reasons:1. The battery power is too low and the camera must be charged.2. The camera has been in standby mode without any operation for longer than 1 minute. In this case, the camera switches off to save battery power.

2. How to Record a Video 1)Continuous Manual Recording(Press after the Camera is powered on)

Press the LED will flash blue for 3 seconds and then goes off, A 10-minute video clip will be recorded .

12

2S

How to Use Your Conbrov T11 Camera

Press again, the blue LED will be on. The device will save the video to the micro SD card and stop recording .

2)Motion Detection Recording (Press after the Camera is powered on)When Motion Detection is activated, the camera will begin recording when there is any movement in front of the camera�not further than25 feet）.The motion sensor detects the environment every 1~ 2 minutes.The camera will begin recording again when it detects new movement.

The Red LED indicator is always on when in motion detection mode.

Press the blue LED will flash once and thered LED will flash 3 times then stays on, the device begins recording video.

13

How to Use Your Conbrov T11 Camera

Press again, the blue and red LED will flash then go off. The device will save the video to the micro SD card and stop recording.

Note: The rotating camera lens and LED allow you to record from different visual fields and directions. PIR sensor and camera angle should be keep on the same horizontal level and PIR detector must not be covered, or it will not able to detect motion.3. How to Switch Into Night Vision Whether under manually recording or PIR activated recording, when ambient light brightness is lower than 10LUX, the camera will automatically switch into night vision and the video is black and white.4. How to Play the Video (1) Connect the T11 camera to computer, press and hold the Power Button for 2 seconds or take out the micro SD, insert it into the card reader (not included), then connect the card reader to computer.

12S power on

2

USB2.0

14

(2) After a few seconds, there will be a removable disk shown on computer. Open it, and then you'll see the video file. Open it to play the videos.

LED Status

Charging

No MicroSD installed

No operation for 60 seconds

Switching off in standby mode

Switching off during video recording

Continuous manual recording

Motion detection recording

Operation LED status indication

Steady yellow and turns off once fully charged

LED flashes blue for 10 times, and the camera turns off

Blue LED turns off (camera turns off)

LED flashes red and blue alternately

LED flashes alternately red and blue

LED flashes blue 3 times and turns off

Red LED indicator keeps on

15

Technical Specifications

Dimensions 65x35x28mmNet weight 53g

Battery LiPoStand-by power consumption 10uA

PIR detection angle 60 degrees

PIR detection distance 5-10 metersCamera angle 120 degrees

Max PIR stand-by time 1 year

Day time recording power consumption 220mA

Max day time recording time 4 hours

Night vision recording power consumption

Max night vision continuously recording time

Full-Charging time 3.5 hours

Resolution 720PFPS 30FPS

Max storage capacity microSD card

Loop recording optional

650mA

1.5 hours

32GB

16

FAQs

1. Q: Why is the camera charging so slowly?A: Considering the camera built-in 1000mah battery and charging current is too low, please charge it with a 5V/1A power adapter.

2. Q:When power on the camera, the blue light flash all the time, and can not record. What should I do?A:Regarding to your problem, When the blue lights blinking continuously, it shows that it can not read the SD card. Please format the SD card to FAT32 on windows system again or change another SD card.

3. Q:Can you access camera video from cell phone?A: NO. This camera can't view video from cell phone.

4. Q: The blue LED flashes fast, video cannot be saved.What should I do?A: The memory card may be damaged, please replace the micro SD card.

5. Q:The motion detection is slow. Is there a way to adjust the motion detection so they will start recording faster?A:When you press MD button, and it takes sometime to detect the environment, the time was influenced by the environment. You could walk frequently in front of the camera to make the camera enter the MD mode faster.

6. Q: Playback mode seems to be in slow motion, not smooth, broken up. How to fix it?A: It may be due to the slow read and write speed of your micro SD card. We recommend using a high-quality Class 10 micro SD card with 32GB capacity.

17

FAQs

7. Q:Can it record through the window?A: You can record through the window if you set the camera in continuous manual recording. Motion detection recording is not working properly through a window. The window will affect motion sensing as the temperature of the window itself will mask temperature changes occurring outside.

8. Q:What does 10 minutes per file mean? Can not it record one 1 hour continuously?A:Each file of 10 minutes means that it continuously records 1 hour, and it will save 6 files, per video file will be 10 minutes. When you view video on computer, it is continuous.

9. Q:Why can't I play back the video on computer?A:We recommend using VLC player for playback if you use a Mac. If you use a window PC, please try KMP player.

10. Q:Why is my camera not being recognized on the computer?A:Please turn on the camera first, then connect the camera to the computer via USB cable.(The blue LED indicator will stay on and the red indicator will flash).Or please use another micro SD card, take care to format the card to FAT32 on window computer. Please reset the camera and try it again.

11. Q: Why am I coming home to hundreds of 1-2 minute clips all with no motion being recorded?A: When you set the camera in motion detection mode, it will start recording when the sensor detects any temperature change in front of the camera within 10 meters (25 feet). Please take care of the followings to avoid frequent trigger: 18

FAQs

1)Don’t place the camera towards the glass doors or windows directly. Considering the PIR has a strong suppression of bright light, please don’t do that in order to weaken the interference of the bright light.

2)Don’t place the camera towards the heat sources such as the air conditioners or the heating systems. Sometimes the air convection between the doors and windows can cause false trigger even. The trigger is closely related to the change of the temperature.

3)Don’t place the camera in a complex environment where the objects can easily swing, such as the flow of people, vehicles and so on. It can cause false trigger too.

18

Warranty

All products sold by the Conbrov Group are covered by a 12-month full replacement warranty.Happy with it? Share your experience with an Amazon review. Or any questions?Our friendly customer services team is ready to help: support@conbrov.comContacting us via the above email address is the quickest way to reach our support team.

For the electronic user manual and more information, please visit:

DisposalElectrical products should not be discarded with household waste. According to the European Directive 2012/19/EC on waste electrical and electronic equipment and its implementation into national law, electrical products used must be collected separately and disposed of at collection points provided for this purpose. Talk with your local authorities or dealer for advice on recycling.

Declaration of conformityConbrov Electron Co., Ltd., Room 908 Huiyicaifu Center, c/o Queshan and Longhua Roads, Shenzhen, China, declares under our sole responsibility that the product Starlight Mini Camera T16, to which this declaration relates, meets all relevant European standards and directives. For the complete declaration of conformity visit our website www.conbrov.com.

19

TrademarksAll trademarks or registered trademarks are the property of their respective owners.

ManufacturerConbrov Electron Co., Ltd. Room 908 Huiyicaifu Center, c/o Queshan and LonghuaRoadsShenzhen, People's Republic of China

Conbrov Electron Co., Ltd. founded in 2003 is an innovative technology research company specialized in personal surveil lance cameras and on-dash cameras. Conbrov products and technology are patent protected by PCT or U.S. Patent Office. Based on years of professional experience and knowledge, we are able to provide the best and most efficient products and customer service.

About Us