SZ170R8 V2 English.Spanish.Korean.Quick Guide【 English · Unfasten the four ICE module attachment...
1
11. Fasten the Smart Fan to the chassis with the four thumbscrews. A. Begin Installation 1. Unscrew 3 thumbscrews of the chassis cover. 2. Slide the cover backwards and upwards. 3. Unfasten the rack mount screws and remove the rack. B. CPU and ICE Installation For safety reasons, please ensure that the power cord is disconnected before opening the case. 1. Unfasten the ICE fan thumbscrews on the back of the chassis. 2. Unfasten the four ICE module attachment screws and unplug the fan connector. 3. Remove the ICE module from the chassis and put it aside. 1. Unlock the DIMM latch. 2. Align the memory module's cutout with the DIMM slot notch. Slide the memory module into the DIMM slot. C. Memory Module Installation 3. Check that the latches are closed, and the memory module is firmly installed. E. Installation of Expansion Cards 1. Unfasten the expansion slot bracket screws. Remove the back panel bracket and put it aside. F. Installation of Expansion Cards 2. Install the PCIe x4 / PCIe x16 card into the PCIe x4 / PCIe x16 slots. 3. Secure the bracket. G. Complete Please press the "Del" key while booting to enter BIOS. Here, please load the optimised BIOS settings. The maximum size acceptable for display cards is 267mm x 120mm x 34.6mm. 1. Replace the cover and refasten the thumbscrews. 2. Complete. Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips are used. (Go to Shuttle's website for the latest memory support list.) Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction. Guidelines for Memory Configuration Before installing DIMMs, read and follow these guidelines for memory configuration. Installing a memory module DDR4 and DDR3/DDR2 DIMMs are not compatible to each other or other DDR DIMMs. Be sure to install DDR4 DIMMs on this motherboard. Follow the steps below to correctly install your memory modules in the memory sockets. Repeat the above steps to install additional memory modules, if required. A DDR4 memory module has a cutout, so it only fits in one direction. 4. First unlock and raise the socket lever. This 1151-pin socket is easily damaged and pins bend quickly.Always use extreme care when installing a CPU and limit the number of times that you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. Follow the steps below to correctly install the CPU into the motherboard CPU socket. Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins and damage of CPU! 6. Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket. DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover when the CPU is not installed. Socket 1151 CPU Triangle Pin1 Marking on the CPU LThe product's colour and specifications may vary from the actually shipping product. 5. Connect the Serial ATA and power cables to the HDD. 3. Connect the Serial ATA Cable to the motherboard. 4. Place the rack in the chassis and refasten the rack. 1. Loosen the purse lock and separate the Serial ATA and power cables. 7. Close the metal load plate, lower the CPU socket lever and lock in place. 8. Spread thermal paste evenly on the CPU surface. 5. Tear off the protective membrane from the metal load plate. Lift the metal load plate on the CPU socket. Dual-Channel mode Population Rule In Dual-Channel mode, the memory modules can transmit and receive data with two data bus lines simultaneously. Enabling Dual-Channel mode can enhance the system performance. The following illustrations explain the population rules for Dual-Channel mode. DIMM1 (Black), Installed DIMM2 (Blue), Installed DIMM3 (Black), Installed DIMM4 (Blue), Installed A B 9. Screw the ICE module to the mainboard. Note to press down on the opposite diagonal corner while tightening each screw. 10. Connect the fan connector. J3 Fan Connectors (FN1,FN2) J2 USB Header (USB1,USB2) 1=5V_USB 2=5V_USB 3=USB A- 4=USB B- 5=USB A+ 6=USB B+ 7=GND 8=GND 9=NULL 10=GND J1 Front Audio Header (JP2) 1=MIC_L 2=GND 3=MIC_R 4=Front_Detect 5=LINE_R 6=Mic_detect 7=sense 8=NULL 9=LINE_L 10=Line_Detect J4 USB 3.0 Header (JP5) 1=5VCC 2=A_RX_N 3=A_RX_P 4=Ground 5=A_TX_N 6=A_TX_P 7=Ground 8=A_Data_N 9=A_Data_P 10=OC 11=B_Data_P 12=B_Data_N 13=Ground 14=B_TX_P 15=B_TX_N 16=Ground 17=B_RX_P 18=B_RX_N 19=5VCC 20=NULL DIMM1 (Black), Empty DIMM2 (Blue), Installed DIMM3 (Black), Empty DIMM4 (Blue), Installed Motherboard Illustration Back Panel SZ170R8 V2 Quick Guide【 English 】 Front Panel Jumper Settings Please do not apply excess amount of thermal paste. 2. Install the M.2 divice into the M.2 slot and secure with screw. D. Component Installation 53R-SZ1703-H601 Safety Information Read the following precautions before setting up a Shuttle XPC. CAUTION Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Disposal of used batteries according to the manufacturer's instructions. Laser compliance statement The optical disc drive in this PC is a laser product. The drive's classification label is located on the drive. CLASS 1 LASER PRODUCT CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. PCIe x16 slot PCIe x4 slot Serial ATA Cable Serial ATA Power Cable J7 Power Connector (JP4) 1=+HD_LED 2=PWR_LED 3=-HD_LED 4=GND 5=RST_SW 6=PWR_SW 7=GND 8=GND 9=NA 10=NULL 9 7 5 3 1 10 8 6 4 2 J6 COM Header (COM1) 1=DCD 2=RXD 3=TXD 4=DTR 5=Ground 6=DSR 7=RTS 8=CTS 9=NA 10=NULL 9 7 5 3 1 10 8 6 4 2 1 3 5 7 9 2 4 6 8 10 1 3 5 7 9 2 4 6 8 10 1=Ground 2=+12V 3=SPEED_SENSE 4=PWM_CTRL Fan Connector 1 2 3 4 4 3 2 1 11 12 13 14 15 16 17 18 19 20 10 9 8 7 6 5 4 3 2 1 Thermal Paste application area Cutout Latch Latch Notch DDR4 288 pin 1.2V 67*2=134 pin 77*2=154 pin 2 1 3 Fan Connector J5 LPC Header (LPC1) 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 1=+12V 2=5V 3=5VSB 4=SERIRQ 5=CLK_48M 6=CLK_33M 7=SIO_RST 8=LFRAME 9=LAD3 10=LAD2 11=-12V 12=3VSB 13=NA 14=LDRQ0 15=SIO_PME 16=LAD1 17=LAD0 18=+3.3V 19=GND 20=NULL Metal load plate Tear off the protective membrane. 1. As shown, unfasten the screw first. M.2 2230 A/E Key slot M.2 2280 M Key slot J2 J3 J4 J7 J6 4x 288 pins DDR4 DIMM Slot Side Speaker Out / Real Speaker Out / Center / Subwoofer Speaker Out Port Front Speaker Out / Line-In Port 2x USB 3.0 & 1x LAN Port ATX Power Connector-PWR1 ATX Power Connector-ATX1 Front Audio Header-JP2 USB Header-USB1 Power Connector-JP4 LGA 1151 FAN Connector-FAN1 2x DisplayPort PCIe x4 Slot PCIe x16 Slot 2x USB 3.0 & 1x LAN Port Clear CMOS Button LPC Header-LPC1 USB 3.0 Header-JP5 2x USB 3.0 & 1x HDMI Port COM Header-COM1 Intel ® Z170 Chipset USB Header-USB2 M.2 2230 AE Key Slot M.2 2280 M Key Slot J5 J2 J1 J3 FAN Connector-FAN2 SATA 3.0 6Gb/s Connector -SATA1,SATA2,SATA3,SATA4 F1. Power On Button F2. Power LED F3. HDD LED F4. USB 3.0 Port F5. Mic In F6. Headphones F1 F2 F3 F6 F5 F4 1 2 SATA 3.0 Connectors Serial ATA HDD 1st 2nd 3rd 4th SATA 3.0 Connectors 2. Place the HDD in the rack and secure with screws from the side. 6. Repeat these steps to install up to four 3.5" HDDs, if desired. VGA Card PCB Chassis Cover 5mm 34.6mm PCIe x16 / PCIe x4 slots The maximum height for memory module is 42mm. 42mm 62RQSZ1700-5201 SZ170V2 English.Spanish.Korean. Traditional Chinese.Japanese. French. German Quick Guide B1. AC Power Socket B2. Serial Port (Optional) B3. DisplayPort B4. HDMI Port B5. USB 3.0 Port B6. LAN Port B7. Clear CMOS Button B8. Front Speaker Out (L/R) Port B9. Line-In Port B10. Side Speaker Out (L/R) Port B11. Real Speaker Out (L/R) Port B12. Center/Subwoofer Speaker Out Port B13. Wireless LAN Perforation (Optional) B1 B2 B8 B11 B12 B10 B13 B7 B3 B4 B9 B5 B6
Transcript of SZ170R8 V2 English.Spanish.Korean.Quick Guide【 English · Unfasten the four ICE module attachment...
11. FastentheSmartFantothechassiswiththefourthumbscrews.
A.BeginInstallation
1.Unscrew3thumbscrewsofthechassiscover.
2.Slidethecoverbackwardsandupwards.
3.Unfastentherackmountscrewsandremovetherack.
B.CPUandICEInstallation
Forsafetyreasons,pleaseensurethatthepowercordisdisconnectedbeforeopeningthecase.
1.UnfastentheICEfanthumbscrewsonthebackofthechassis.
2.UnfastenthefourICEmoduleattachmentscrewsandunplugthefan connector.
3.RemovetheICEmodulefromthechassisandputitaside.
1.UnlocktheDIMMlatch.2.Alignthememorymodule'scutoutwiththeDIMMslotnotch. SlidethememorymoduleintotheDIMMslot.
C.MemoryModuleInstallation
3. Checkthatthelatchesareclosed,andthememorymoduleisfirmlyinstalled.
E.InstallationofExpansionCards
1.Unfastentheexpansionslotbracketscrews. Removethebackpanelbracketandputitaside.
F.InstallationofExpansionCards
2. InstallthePCIex4/PCIex16cardintothePCIex4/PCIex16slots.3.Securethebracket.
G.Complete
Pleasepressthe"Del"keywhilebootingtoenterBIOS.Here,pleaseloadtheoptimisedBIOSsettings.
Themaximumsizeacceptablefordisplaycardsis267mmx120mmx34.6mm.
1.Replacethecoverandrefastenthethumbscrews.
2.Complete.
Makesurethatthemotherboardsupportsthememory.Itisrecommendedthatmemoryofthesamecapacity,brand,speed,andchipsareused.(GotoShuttle'swebsiteforthelatestmemorysupportlist.)Memorymoduleshaveafoolproofdesign.Amemorymodulecanbeinstalledinonlyonedirection.Ifyouareunabletoinsertthememory,switchthedirection.
GuidelinesforMemoryConfiguration BeforeinstallingDIMMs,readandfollowtheseguidelinesformemory configuration.
InstallingamemorymoduleDDR4andDDR3/DDR2DIMMsarenotcompatibletoeachotherorotherDDRDIMMs.BesuretoinstallDDR4DIMMsonthismotherboard.Followthestepsbelowtocorrectlyinstallyourmemorymodulesinthememorysockets.
Repeattheabovestepstoinstalladditionalmemorymodules,ifrequired.
ADDR4memorymodulehasacutout,soitonlyfitsinonedirection.
4.Firstunlockandraisethesocketlever.
This1151-pinsocketiseasilydamagedandpinsbendquickly.AlwaysuseextremecarewheninstallingaCPUandlimitthenumberoftimesthatyouremoveorchangetheCPU.BeforeinstallingtheCPU,makesuretoturnoffthecomputerandunplugthepowercordfromthepoweroutlettopreventdamagetotheCPU.
FollowthestepsbelowtocorrectlyinstalltheCPUintothe motherboardCPUsocket.
PleasebeawareoftheCPUorientation,DONOTforcetheCPUintothesockettoavoidbendingofpinsanddamageofCPU!
6. PleaseorientatetheCPUcorrectlyandaligntheCPUnotcheswiththe socketalignmentkeys.MakesuretheCPUsitsperfectlyhorizontal,then pushitgentlyintothesocket.
DONOTtouchsocketcontacts.ToprotecttheCPUsocket,alwaysreplacetheprotectivesocketcoverwhentheCPUisnotinstalled.
Socket 1151 CPU
TrianglePin1Marking
ontheCPU
LTheproduct'scolourandspecificationsmayvaryfromtheactuallyshippingproduct.
5.ConnecttheSerialATAandpowercablestotheHDD.
3.ConnecttheSerialATACabletothemotherboard.4.Placetherackinthechassisandrefastentherack.
1. LoosenthepurselockandseparatetheSerialATAandpowercables.
7. Closethemetalloadplate,lowertheCPUsocketleverandlockinplace.8.SpreadthermalpasteevenlyontheCPUsurface.
5.Tearofftheprotectivemembranefromthemetalloadplate.Liftthe metalloadplateontheCPUsocket.
Dual-ChannelmodePopulationRule InDual-Channelmode,thememorymodulescantransmitandreceive datawithtwodatabuslinessimultaneously.EnablingDual-Channel modecanenhancethesystemperformance.Thefollowingillustrations explainthepopulationrulesforDual-Channelmode.
DIMM1(Black),Installed
DIMM2(Blue),Installed
DIMM3(Black),Installed
DIMM4(Blue),Installed
A
B
9. ScrewtheICEmoduletothemainboard.Notetopressdownonthe oppositediagonalcornerwhiletighteningeachscrew.
10.Connectthefanconnector.
J3 FanConnectors(FN1,FN2)
J2 USBHeader(USB1,USB2)
1=5V_USB 2=5V_USB3=USBA- 4=USBB-5=USBA+ 6=USBB+7=GND 8=GND9=NULL 10=GND
J1 FrontAudioHeader(JP2)
1=MIC_L 2=GND3=MIC_R 4=Front_Detect5=LINE_R 6=Mic_detect7=sense 8=NULL9=LINE_L 10=Line_Detect
J4 USB3.0Header(JP5)
1=5VCC 2=A_RX_N3=A_RX_P 4=Ground5=A_TX_N 6=A_TX_P7=Ground 8=A_Data_N9=A_Data_P 10=OC11=B_Data_P 12=B_Data_N13=Ground 14=B_TX_P15=B_TX_N 16=Ground17=B_RX_P 18=B_RX_N19=5VCC 20=NULL
DIMM1(Black),Empty
DIMM2(Blue),Installed
DIMM3(Black),Empty
DIMM4(Blue),Installed
MotherboardIllustration
BackPanel
SZ170R8V2QuickGuide【English】FrontPanel JumperSettings
Pleasedonotapplyexcessamountofthermalpaste.
2. InstalltheM.2diviceintotheM.2slotandsecurewithscrew.
D.ComponentInstallation
53R-SZ1703-H601
SafetyInformationReadthefollowingprecautionsbeforesettingupaShuttleXPC.
CAUTION
Incorrectlyreplacingthebatterymaydamagethiscomputer.ReplaceonlywiththesameorequivalentasrecommendedbyShuttle.Disposalofusedbatteriesaccordingtothemanufacturer'sinstructions.
Laser compliance statement
TheopticaldiscdriveinthisPCisalaserproduct.Thedrive'sclassificationlabelislocatedonthedrive.
CLASS 1 LASER PRODUCT
CAUTION:INVISIBLELASERRADIATIONWHENOPEN.AVOIDEXPOSURETOBEAM.
PCIex16slot
PCIex4slot
SerialATACable
SerialATAPowerCable
J7 PowerConnector(JP4)
1=+HD_LED 2=PWR_LED3=-HD_LED 4=GND5=RST_SW 6=PWR_SW7=GND 8=GND9=NA 10=NULL
97531
108642
J6 COMHeader(COM1)
1=DCD 2=RXD3=TXD 4=DTR5=Ground 6=DSR7=RTS 8=CTS9=NA 10=NULL
97531
108642
13579
246810
1
3
5
7
9
2
4
6
8
10
1=Ground2=+12V3=SPEED_SENSE4=PWM_CTRL
FanConnector
1
2
3
4
4321
11 12 13 14 15 16 17 18 19 20
10987654321
ThermalPasteapplicationarea
CutoutLatch LatchNotch
DDR4288pin1.2V
67*2=134pin77*2=154pin
2
1
3
FanConnector
J5 LPCHeader(LPC1)10
9
8
7
6
5
4
3
2
1
20
19
18
17
16
15
14
13
12
11
1=+12V 2=5V3=5VSB 4=SERIRQ5=CLK_48M 6=CLK_33M7=SIO_RST 8=LFRAME9=LAD3 10=LAD211=-12V 12=3VSB13=NA 14=LDRQ015=SIO_PME 16=LAD117=LAD0 18=+3.3V19=GND 20=NULL
Metalloadplate
Tearofftheprotectivemembrane.
1.Asshown,unfastenthescrewfirst.
M.22230A/EKeyslotM.22280MKeyslot
J2
J3
J4
J7
J6
4x288pinsDDR4DIMMSlot
SideSpeakerOut/RealSpeakerOut/Center/SubwooferSpeakerOutPort
FrontSpeakerOut/Line-InPort
2xUSB3.0&1xLANPort
ATXPowerConnector-PWR1
ATXPowerConnector-ATX1
FrontAudioHeader-JP2
USBHeader-USB1
PowerConnector-JP4
LGA1151
FANConnector-FAN1
2xDisplayPort
PCIex4Slot
PCIex16Slot
2xUSB3.0&1xLANPortClearCMOSButton
LPCHeader-LPC1
USB3.0Header-JP5
2xUSB3.0&1xHDMIPort
COMHeader-COM1
Intel®Z170Chipset
USBHeader-USB2
M.22230AEKeySlot
M.22280MKeySlot
J5
J2
J1
J3 FANConnector-FAN2
SATA3.06Gb/sConnector-SATA1,SATA2,SATA3,SATA4
F1.PowerOnButton
F2.PowerLED
F3.HDDLED
F4.USB3.0Port
F5.MicIn
F6.Headphones
F1F2
F3
F6F5
F4
1
2
SATA3.0Connectors
SerialATAHDD
1st
2nd
3rd
4th
SATA3.0Connectors
2.PlacetheHDDintherackandsecurewithscrewsfromtheside.
6.Repeatthesestepstoinstalluptofour3.5"HDDs,ifdesired.
VGACardPCB
ChassisCover
5mm 34.6mm
PCIex16/PCIex4slots
Themaximumheightformemorymoduleis42mm.
42mm
62RQSZ1700-5201 SZ170V2English.Spanish.Korean.Traditional Chinese.Japanese.French. German Quick Guide
B1.ACPowerSocketB2.SerialPort(Optional)B3.DisplayPortB4.HDMIPortB5.USB3.0PortB6.LANPortB7.ClearCMOSButtonB8.FrontSpeakerOut(L/R)PortB9. Line-InPortB10.SideSpeakerOut(L/R)PortB11.RealSpeakerOut(L/R)PortB12.Center/Subwoofer SpeakerOutPortB13.WirelessLANPerforation (Optional)
B1
B2
B8
B11
B12
B10
B13
B7
B3 B4
B9
B5
B6
