Synergy Unit 9 - 3182 Orlando Drive Energy - Intellivex - Product_Catalogue_2010.pdf · Unit 9 -...

© Synergy Energy Inc. All Rights Reserved.

Synergy Energy Inc.

Unit 9 - 3182 Orlando Drive

Mississauga, Ontario, L4V 1R5, Canada

Toll free tel: 1-866-866-5822

Toll free fax: 1-866-866-5716

[email protected]

www.SynergyEnergyInc.com

SynergyEnergy

Transformers for the 21st century

2010 Edition

VFDSHTT2HPSHTTHS CTTHarmonic Mitigating:

HET.LHESTHPSHTTHS HETHigh Efficiency: HET.K

HTT2HPSHTTHSElectronic Load

Rated:HET.K VFDS CTT

CTT.ASpecial:

http://www.synergyenergyinc.com




Catalogue Update Request

To view a specific section of the catalogue, please click on the related following topic:

Profile ........................................................................................................................3

........................................................................................4

..................................................................................................................5

................................................................................................................7

.............................................................................................9

...................................................................................................................10

........................................................11

...................................................13

.........................................................................15

........................17

.......................................................19

.............................................21

.........................................................23

..........................................25

........................................27

.................................29

.................................................................................................................33

...................................................................................................34

..................................................................................35

.......................................................................................36

.............................................................................................37

Fact Sheet

Compliance

Product Selection Guide

Products

SmartSkid

Warranty & Liability

Terms & Conditions - Canada

Terms & Conditions - USA

Products Return Policy

HPS

HTT

HS

HTT2

CTT

VFDS

HET

HET.K

HET.L

HEST

- Harmonic Premium Solution

- Harmonic Treating Transformer

- Harmonic Solution

- Harmonic Treating Transformer 2 Two Outputs

- Current Treating Transformer

- Variable Frequency Drive Solution

- High Efficiency Transformer

- High Efficiency Transformer K Rated

- High Efficiency Transformer Low Cost

- High Efficiency Single-phase Transformer

............................................................................................31CTT.A - Special

Table of Contents

1-866-866-5822 [email protected] 1-866-866-5716 WWW. SynergyEnergyInc . COM



With emphasis on High Efficiency (NEMA-TP1) and Harmonics Mitigation criteria,

Synergy Energy Inc. is a premier designer and manufacturer of dry-type, copper

wound Transformers for the 21st Century.

The products offered by Synergy Energy Inc. are designed with high engineering

expertise and the latest computer software. While in production, each and every

transformer goes through several rigorous quality controls and a unique barcode

controlled production tracking system eliminate all possible human errors to ensure

100% design compliance.

Building towards its mission To Save Energy and Improve Power Quality,

Synergy Energy Inc. has dedicated both its technical expertise and manufacturing

capabilities towards introducing a complete line of High Efficiency and Harmonic

Mitigating products that meet and exceed the efficiency standards and improve the

Power Quality of their customers' electrical systems. High efficiency is an integral

part of Synergy Energy Inc.’s designs.

Synergy Energy Inc. is an Energy Star partner and capable of manufacturing

transformers up to 5000 kVA and 25 kV in two New Jersey (USA) and Ontario

(Canada) plants.

The products offered by Synergy Energy Inc. are UL, INTERTEK and CE approved.

They meet or exceed the applicable NEMA, ANSI, IEEE, CSA and UL standards

and are backed with one of the longest linearly distributed pro-rated warranties in

the industry.

Customized transformers and products designed by Synergy Energy Inc. are all

wound with Copper, brazed internally and have vibration dampers between the core

and enclosure. To increase the product flexibility, options such as lug kits, various

enclosure types and colors, ceiling mount, digital voltmeter, over-temperature alarm,

ground bar, thermal switches, over-current alarm, ultra quiet, and electrostatic

shields are offered as options.

Moreover, with the unparalleled design and introduction of the innovative

SmartSkid®, and its inclusion as an integrated component of all Standard

Transformers, Synergy Energy Inc. has further overcome the safety and installation

challenges of securely and easily transferring, lifting, and mounting the units.

In partnership with our clients and their technical teams, it is our core philosophy to

continually embark on new challenges in the fields of design and production of dry

type Transformers and Reactors, and introduce reliable and cost effective solutions.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E

i NTERTEK ENERGYPERFORMANCE

VERIFIED

RENDEMENTENERGETIQUE

VERIFIE

Sm

art

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.


Profile



To request receiving the electronic copy of the latest and updated

versions of Synergy Energy Inc catalogue on a CD, please either fax

this completed form to the following Toll Free Number or contact us

via e-mail:

Toll Free: 1-866-866-5716

Please Print Clearly:

Date:

Full Name:

Company:

Title:

e-mail:

Website:

Address:

Please check, If you would wish to receive product updates via e-mail.

Disclaimer: The contact information obtained herewith is merely for the purpose of processing your inquiry by Synergy Energy Inc. and will not be shared and/or communicated with any third party firm and/or individuals.

Street No., Street Name, Unit No.

City/Town/County, Province/State

Postal Code/Zip Code, Country

Catalogue Update Request




Nature of harmonics:

During the last three decades we have moved away from linear loads such as electrical motors with mechanical speed control, and heaters towards non-linear loads such as computers, printers, and light dimmers. Therefore, attention should be given to the transformer on the load line of an electrical system. Any distortions in the voltage or current wave cause harmonics. Harmonics are multiples of base frequency (base frequency in North America is 60 Hz) that when added together, form the actual wave form. Depending on the amount of different harmonics present in the electrical system, the ideal sinusoidal wave can take different shapes.

Sources of harmonics:

Today's loads draw current differently compared to the loads of the past. Equipment such as computers, monitors, copiers, fax machines, scanners, and printers were not as frequently used in past decades. In today's industries, three phase Non-linear loads such as Variable Frequency Drives are widely used as well. Also, manufacturers are taking advantage of robots, plasma cutters and other electronic and computer controlled equipment that is relatively new to the industry. All of these loads create harmonics with damaging effects and need to be addressed accordingly.

Common types of harmonics:

The most dominants types of harmonics that have the greatest magnitude and cause the most damage are 3rd, 5th and 7th. Single-phase electronic loads such as computers, monitors, printers, copiers, scanners, and fax machines have a wide spectrum in these harmonics. Three phase loads such as Variable Frequency Drives and manufacturing robots create mostly 5th and 7th harmonics, if they are 6 pulse drives, and otherwise 11th and 13th harmonics, if they are of 12 pulse drives nature.

Effects of harmonics:

Different harmonics have varying effects on multiple parts of the electrical system. They can cause equipment to malfunction and/or fail, transformers to overheat, and a reduction in transformer capacity (leading to electrical infrastructure over sizing).

When harmonics are applied to transformers, they can easily overheat and despite their ruggedness burn long before they reach their nominal capacities. A study conducted by IEEE 1996 shows harmonics can cause a transformer to reach its maximum temperature rise when it is loaded to just 50% of its capacity.

0 720180 360 540

Wave Angle In Degrees

Wave Shape with Harmonics

Front


Fact Sheet



Third harmonics and its odd multiples get trapped in the delta primary of a standard

Delta-Wye transformer causing it to overheat and reduce its efficiency. The extra

heat will also require extra environmental cooling that will increase the electrical

consumption.

Fifth and seventh harmonics pass through the transformer to the utility grid causing

the reduction of Power Factor and an increase in utility bill.

Solution:

Transformers are the most important infrastructure of any electrical system and are

required to be sized and applied with full attention to harmonic creating loads.

Our Unsurpassed Solution:

By considering the K load factor, Synergy Energy Inc. designs and manufactures the

harmonic mitigating transformers, which are capable of mitigating the 3rd, 5th, 7th,

9th, 13th and 15th harmonics at the system level.

Harmonic mitigating capabilities of transformers designed and manufactured by

Synergy Energy Inc. makes them facilitators for IEEE 519 conformity. Furthermore,

the transformers meet the low Audible Noise levels of NEMA and are designed,

manufactured, and tested in accordance to all applicable standards of UL, CSA,

IEEE, ANSI, and NEMA.

Transformers designed and manufactured by Synergy Energy Inc. meet and exceed

the required efficiency levels of NEMA TP-1, CSA 802.2 and US Department of

Energy (DOE) CSL-3 standards. Furthermore, the efficiency compliance with NEMA

and CSA standards of the transformers are verified by the third party verification

body, Intertek, one of the most trusted test organizations in the world. Verified

products carry the Intertek Efficiency Verification logo together with the related

Verification number.

With numerous optional features such as lug kits, various enclosure types and

colors, ceiling and wall mount brackets and hardware, digital voltmeter with selector

switch, audio/visual over-temperature alarm, ground busbar, phase loss alarm,

thermal sensors, over-current alarm, various temperature rise & frequency, ultra

quiet, capacitor life indicator, THD indicator and electrostatic shields are offered as

options, transformers and products designed and manufactured by Synergy Energy

Inc. are among the most selected and recommended ones by technical experts in

the industry.

The finished products are shipped in a shrink-wrapped, gray NEMA 3R enclosure

with corner protectors on our unique SmartSkid® for safe and effortless

transportation and installation.

Wave Angle In Degrees

0 720180 360 540

Wave Shape without Harmonics

Back

Sm

art

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.


Fact Sheet



Quality & Safety Compliance:

Considering the hazardous result of a faulty product, the importance of compliance of a device, which is designed and manufactured for electrical regulating application is prominent.

In addition to the self regulating quality and compliance principles, which are available to manufacturer of such products as part of the best manufacturing practice, it is becoming more apparent that independent third party verification is extremely important.

In adhering to the internationally recognized quality principles, where applicable, products manufactured by Synergy Energy Inc. bear the following Quality and Safety compliance markings:

CE Marking:

The CE marking (also known as CE mark) is a mandatory conformity mark on many products placed on the single market in the European Economic Area (EEA). The CE marking certifies that a product has met EU consumer safety, health or environmental requirements. Furthermore, CE marking is a declaration by the manufacturer that the product meets all the appropriate provisions of the relevant legislation implementing certain European Directives.

ETL Marking:

A product bearing the ETL Listed Mark is determined to have met the minimum requirements of prescribed product safety standards. Specifically, the mark indicates that the manufacturer's production site conforms to a range of compliance measures and is subject to periodic follow up inspections to verify continued conformance. The verification is conducted by an independent Nationally Recognized Testing Laboratory (NRTL), such as Intertek, which is required to be recognized by the Occupational Safety and Health Administration (OSHA).

UL Marking:

Underwriters Laboratories® Inc. (UL) is an independent product safety certification organization. A manufacturer of a UL-certified product must demonstrate compliance with the appropriate safety requirements, many of which are developed by UL. A manufacturer must also demonstrate that it has a program in place to ensure that each copy of the product complies with the appropriate requirements. UL conducts periodic, unannounced follow-up inspections at manufacturers' locations to check ongoing compliance.

Product Tracking Process:

In an effort to streamline the process of tracking a product from the initial point of sales to final shipment to the customer, Synergy Energy Inc. has developed a customized, unprecedented, and revolutionary Management Information System (MIS), which has been praised by both the quality verification bodies and its clients.

Front

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE


Compliance

0000-ISO000-SE0000



Adapting a sophisticated bar-coding system, where printed labels are placed on both internal and external components of a products, has enabled Synergy Energy Inc. in implementing the most customized and rigorous product tracking system in the industry to verify all the following steps in real time, gather and store the corresponding technical and quality related information for both internal and external future sales, manufacturing, quality and audit references:

Point of Sales and order entry.

Release of the order to design team for development of the design specification

Release of the order to manufacturing.

Tracking all steps of the manufacturing such as winding, stacking, connection, final assembly, and shipping, where all corresponding related products are bar-coded.

Tracking all quality testing steps and producing the corresponding test results

Back


Compliance



Ultra High efficiency harmonic mitigating transformer specifically designed to deliver enhanced power quality by treating the harmonics in the electrical system that are generated by single phase non-linear loads. HPS treats 5th, 7th, 11th, and 13th harmonics at the system level.

A three-phase isolation transformer capable of handling loads up to K30 without derating. HTT mitigates 3rd, 9th and all other third order harmonics in its secondary windings through Flux Cancellation technology and 5th, 7th, 11th and 13th harmonics through phase shifting at the system level.

With small footprint and a great replacement for Delta-Wye transformers, one of the most economical solutions for harmonic problems. HS is designed to handle K-20 load profile and is capable of mitigating the 3rd, 5th, 7th, 9th and 15th harmonics at the system level.

Highly advanced dual output transformer with extraordinary harmonic mitigating capabilities. HTT2 mitigates all the 3rd order harmonics together with 5th and 7th ones in its windings. Phase shifting technology combined with low zero sequence impedance and balanced output impedances enables HTT2 to efficiently and reliably mitigate the harmonics.

Har

mon

ic M

itiga

ting

Hig

h Ef

ficie

ncy

Prod

ucts

(Dire

ct R

epla

cem

ent f

or D

istr

ibut

ion

Tran

sfor

mer

)

Elec

tron

ic L

oad

Rat

ed P

rodu

cts

HPSHarmonic PremiumSolution

HTTHarmonicTreatingTransformer

Three-phase Four-wire harmonic mitigating and Neutral Current reducing device, CTT is designed for parallel installation in the electrical system and it traps the third order harmonics by creating a low impedance pathway.

CTTCurrentTreatingTransformer

HTT2HarmonicTreatingTransformer2 Two Outputs

HSHarmonicSolution

As a replacement for standard Delta-Wye transformer, the Ultra High Efficiency HET is to reduce the operating cost of the facilities. It is the ideal transformer for supplying power to panels or equipment with high linear load concentration.

HETHighEfficiencyTransformer

Three phase high efficiency isolation transformers derated to the K-rating levels specified by UL. Typical installation of HET.K would be where non-linear loads are present. The required K-rating increases with increased amounts of Total Harmonic Distortion (THD) in the electrical system.

HET.KHighEfficiencyTransformerK Rated

A low cost solution for raising the overall efficiency of a facility, HET.L transformers delivers quiet and efficient power with short return on investment.

Common Features of Harmonic Mitigating & High Efficiency Products: Copper wound, Internally brazed, Vibration damper between core clamping brackets and enclosure, Insulation class 220 °C, Natual Convection Cooling with Air (ANN), NEMA 3R Enclosure, 3rd party Intertek Efficiency Verification, and SmartSkid®.

HET.LHighEfficiencyTransformerL Low Cost

While providing efficient power to single-phase loads, HEST improves the overall efficiency of the facility and returns the investment in a short period. With their low maximum temperature rise, HEST products run cooler than a standard single-phase transformer under similar load and condition.

HESTHighEfficiencySingle-phaseTransformer

High Efficiency device designed to mitigate 5th and 7th harmonics created by nonlinear load such as Variable Frequency Drives. It is an efficient, reliable, and long lasting electromagnetic based device. Reduction of the 5th and 7th harmonics provides cleaner voltage to the other equipment in the facility, and reduces equipment malfunction and failure.

VFDSVariableFrequencyDriveSolution

Smar

tSkid

is a

Reg

ister

ed T

rade

Mar

k of

Syn

ergy

Ene

rgy

Inc.


Product Selection Guide

Disclaimer: Strive for continuous improvement may result in modifications to the technical specifications without notice.



Following pages are to introduce the list of Standard Key Features and encompass Optional Elements of the products, which are designed and manufactured by the Synergy Energy Inc.

For additional Engineering and Technical details of the products, please do not hesitate to contact us.


Products




HPS (Harmonic Premium Solution) is an Ultra High efficiency harmonic

mitigating transformer specifically designed to deliver enhanced power quality by

treating the harmonics in the electrical system that are generated by single

phase non-linear loads such as computers, monitors, printers, copiers, scanners,

televisions, and electronic ballasts. When phase shifted, it treats 5th, 7th, 11th,

and 13th harmonics at the system level. Harmonic mitigating capabilities of HPS

makes it a great facilitator for IEEE 519 conformity. It is designed as a three-

phase isolation transformer capable of handling load profiles of up to K30 without

derating.

Astonishing high efficiency and low operating cost of HPS results in a quick return on investment. It will also

improve the bottom line by reducing equipment malfunction, equipment failure, downtime, and scheduled

equipment maintenance. Efficiency level of HPS easily exceeds the levels required by NEMA TP-1, CSA 802.2-

06 and US DOE CSL-3 standards. The efficiency of HPS is third party verified by Intertek, one of the most

trusted test organizations in the world. It also bears the Intertek efficiency logo together with the related

verification number. HPS products are in line with KYOTO accord requirements for reduction of greenhouse

gasses and carry the longest warranty in the industry.

Similar to any other Synergy Energy Transformers, HPS has front access to all connection points (Primary,

Secondary, Voltage Taps, Ground Lugs, Electrostatic Shields, etc). HPS accepts a wide variety of extra options.

The standard version of HPS has a maximum temperature rise of 130 °C with two, full width copper

electrostatic shields and Six primary voltage taps (Two taps above and four taps bellow the nominal voltage).

The finished product is shipped in a shrink-wrapped, gray NEMA 3R enclosure with corner protectors on our

unique SmartSkid® for safe and effortless transportation and installation. For more information about

SmartSkid® and its advantages, please refer to the SmartSkid® section of catalogue.

HP

S is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE

Front


Standard Features:

2x2.5% FCAN & 4x2.5% FCBN (Brazed)

SmartSkid®

50 years (Pro-Rated)

Exceeds NEMA TP1, CSA 802.2-06 & CSL-3

Intertek

Three Phase, Dry, Isolation, Common Core

Air with Natural Convection (ANN)

Copper, Internally Brazed

130 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Efficiency:

3rd Party Efficiency Verification:

Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:

200% of Line CurrentNeutral Rating:

Audible Noise Level:

Between the core clamping brackets and the enclosureVibration Dampers:

Enclosure Type:

HPS


http://www.synergyenergyinc.com/Synergy_Energy_Inc_hps.html



HP

S is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

Note: Options depicted in RED will increase the manufacturing cost of the product and its sales price. For further details, consult your local area

representative or Synergy Energy Inc.

Key Optional Features:

Model Number Creation:

Primary Voltage: Up to 25 kV (600 V and below are standard voltages at no extra charge)

Phase Shift: Zero or 30 Degrees

Secondary Voltage: Up to 25 kV (600 V and below are standard voltages at no extra charge)

Product: HPS

Rating: 9 for 9 kVA up to 5000 for 5000 kVA

Temperature Rise: 130 for 130 °C, 115 for 115 °C and 80 for 80 °C

Enclosure Color: GRY for Gray, BLU for Royal Blue, RED for Red (Other colors are available)

Example: HPS with 75 kVA Rating, Zero Degrees Phase Shift, 480 V Primary, 208/120 V Secondary, 130 °C

Temperature Rise, 60 Hz Frequency, 2 Electrostatic Shields, in Gray NEMA 3R Enclosure

Model Number: HPS-75-0-480-208-130-60-2S-N3R-GRY

Frequency: 60 for 60Hz, 50 for 50Hz

Enclosure: CC for NO Enclosure, N3R for NEMA 3R, N4 for NEMA 4 (Totally enclosed)

Electrostatic Shield: 2S for Two Shields, 3S for Three Shields

HPS- kVA - PS - PV - SV - TEMP - FRQ - SHLD - ENC - COL


HPS

Disclaimer: Our strive for continuous improvement may result in modifications to the technical specifications without notice.

10987654321

10

9

8

7

6

5

4

3

2

1

Back

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount

Over-Temperature Alarm

To create a model number, match the numbers to the corresponding Key Optional Features and reference the related

abbreviations in the designated location as depicted below:

The additional options available for the product are listed below. Additional options are not abbreviated in the part

number of the product and should be listed separately at the time of order. Please note that some of these options may

not be available depending on product specification. For complete details please refer to the related page in the

"options" section of the catalogue.

Additional Options:

http://www.synergyenergyinc.com/Synergy_Energy_Inc_hps.html



HTT (Harmonic Treating Transformer) products are one of the most popular

products amongst specifying engineers. HTT is ideally used in harmonic rich

environment, where most of the load on the electrical system is nonlinear type

such as computers, monitors, printers, copiers, scanners, televisions, and

electronic ballasts.

HTT is a three-phase isolation transformer capable of handling load profiles of

up to K30 without derating. It mitigates 3rd, 9th and all other third order

harmonics in its secondary windings through Flux Cancellation technology and

5th, 7th, 11th and 13th harmonics through phase shifting at the system level.

HTT is a high efficiency transformer that exceeds the efficiency levels required

by NEMA TP-1, CSA 802.2-06 and US DOE CSL-3 standards. The high

efficiency of HTT is third party verified by Intertek, one of the most trusted test

organizations in the world and bears the related logo and verification number.

Similar to any other Synergy Energy transformers, HTT has front access to all its connection points (Primary,

Secondary, Voltage Taps, Ground lugs, Electrostatic Shields, etc).

HTT accepts a wide variety of extra options. The standard version of HTT has a maximum temperature rise of

130 °C with Six primary voltage taps (Two taps above and four taps bellow the nominal primary voltage) and

one full width copper electrostatic shield between the primary and secondary Windings.




HT

T is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE

Front


Standard Features:


SmartSkid®



Intertek




130 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Efficiency:


Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:




Enclosure Type:

HTT


http://synergyenergyinc.com/Synergy_Energy_Inc_htt.html



HT

T is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.





Primary Voltage: Up to 13800 V (600 V and below are standard voltages at no extra charge)


Secondary Voltage: Up to 13800 V (600 V and below are standard voltages at no extra charge)

Product: HTT


Temperature Rise: 130 for 130 °C, 115 for 115 °C, 80 for 80 °C and 65 for 65 °C


Example: HTT with 75 kVA Rating, Zero Degrees Phase Shift, 480 V Primary, 208/120 V Secondary, 130 °C


Model Number: HTT-75-0-480-208-130-60-2S-N3R-GRY



Electrostatic Shield: 1S for One Shield, 2S for Two Shields, 3S for Three Shields

HTT- kVA - PS - PV - SV - TEMP - FRQ - SHLD - ENC - COL


HTT


10987654321

10

9

8

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount






Additional Options:



http://synergyenergyinc.com/Synergy_Energy_Inc_htt.html



HS (Harmonic Solution) products are three-phase Isolation type, harmonic

mitigating transformers. HS is designed with small footprint, making it a great

replacement for Delta-Wye transformers.

HS is one of the most economical solutions for harmonic problems caused by

single-phase non-linear loads. HS is designed to handle K-20 load profile and is

capable of mitigating the 3rd, 5th, 7th, 9th and 15th harmonics at the system

level.

Harmonic mitigating capabilities of HS make it a facilitator for IEEE 519

conformity. HS meets the low Audible Noise levels of NEMA ST-20 and is

designed, manufactured, and tested in accordance to all applicable standards of

UL, CSA, IEEE, ANSI, and NEMA.

HS transformers are built with efficiency levels higher than what is required by NEMA TP-1 and CSA 802.2-06

standards and exceeds US DOE CSL-3 efficiency levels.. The efficiency level of HS line of products is third

party verified by Intertek, one of the most trusted test organizations in the world. HS products carry the Intertek

Efficiency Verification logo together with the related verification number. Similar to any other Synergy Energy

product, HS has front access to all connection points (Primary, Secondary, and Voltage Taps).

HS accepts a wide variety of extra options. The standard HS has a maximum temperature rise of 150 °C with

Six primary voltage taps (Two taps above and four taps bellow nominal).

The finished product is shipped in a shrink-wrapped, gray NEMA 3R

enclosure with corner protectors on our unique SmartSkid® for safe and

effortless transportation and installation. For more information about

SmartSkid® and its advantages, please refer to the SmartSkid® section of

catalogue.

HS

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE

Front


Standard Features:


SmartSkid®


Intertek




150 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Efficiency:


Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:




Enclosure Type:

HS



http://synergyenergyinc.com/Synergy_Energy_Inc_hs.html






Product: HS









Example: HS with 75 kVA Rating, Zero Degrees Phase Shift, 480 V Primary, 208/120 V Secondary, 130 °C


Model Number: HS-75-0-480-208-130-60-2S-N3R-GRY

HS- kVA - PS - PV - SV - TEMP - FRQ - SHLD - ENC - COL



HS

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.


HS


10

10

9

9

8

8

7

7

6

6

5

5

4

4

3

3

2

2

1

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:

http://synergyenergyinc.com/Synergy_Energy_Inc_hs.html



The HTT2 (Harmonic Treating Transformer with two outputs) is a highly

advanced dual output Isolation transformer with extraordinary harmonic

mitigating capabilities. The HTT2 mitigates all of the 3rd order harmonics

together with 5th and 7th harmonics in its windings. Phase shifting technology,

combined with low zero sequence impedance and balanced output impedances,

enables the HTT2 to efficiently and reliably mitigate the harmonics created by

nonlinear loads such as computers, monitors, printers, copiers, rectifiers, robots

and Variable Frequency Drives.

Each one of HTT2 outputs can feed a three phase, four wire panel and

simultaneously cancel their 5th and 7th harmonics against each other and

HT

T2 is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

Front


Standard Features:


SmartSkid®


Dual Output, Dry, Isolation, Common Core



130 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:




Enclosure Type:

mitigate all of their third order harmonics through its integrated Flux Cancellation Technology.

Although it is preferred to have equal loads on the two outputs (50 - 50) of the HTT2, for safety reasons, each one

of the outputs is designed to handle 60% of its nominal capacity as long as the total load on the transformer does

not exceed its rated capacity. For example, a 150 kVA HTT2 can deliver a total of 416 Amps on its 208 V outputs.

One output can be loaded up to 250 Amps as long as the load on the other output does not exceed 166 Amps.

The harmonic mitigating capability of the HTT2 makes it a great facilitator for of IEEE 519 conformity. HTT2

transformers have front access to all of their connection points (primary, secondary, and voltage taps). They

accept a wide variety of extra options. The standard version of HTT2 has a maximum temperature rise of 130°C

with four primary voltage taps (two taps above and two taps below nominal).


unique SmartSkid®, for safe and effortless transportation and installation. For more information about SmartSkid®

and its advantages, please refer to the SmartSkid® section of the catalogue.

HTT2


http://synergyenergyinc.com/Synergy_Energy_Inc_htt2.html



HT

T2 is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

Primary Voltage: Up to 4160 V

Secondary Voltage: Up to 600 V

Product: HTT2









Example: HTT2 with 75 kVA Rating, 480 V Primary, 208/120 V Secondary, 130 °C Temperature Rise,

60 Hz Frequency, 1 Electrostatic Shield, in Gray NEMA 3R Enclosure

Model Number: HTT2-75-480-208-130-60-1S-N3R-GRY

HTT2- kVA - PV - SV - TEMP - FRQ - SHLD - ENC - COL




HTT2


987654321

9

8

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:

http://synergyenergyinc.com/Synergy_Energy_Inc_htt2.html



Before the electronic age, the most common cause of neutral current was the

unbalanced load on phases, but these days, even if the phases are completely

balanced, the neutral current still flows. The fact is, the neutral current in our

electrical systems is a byproduct of third order harmonics. It creates voltage

distortion, equipment malfunction, equipment failure, and downtime. The CTT is a three-phase four-wire harmonic mitigating and neutral current

reducing device. The CTT is designed for parallel installation in the electrical

systems. It traps the third order harmonics by creating a low impedance pathway.

The astonishing capability of the CTT becomes more evident when it is installed

in close proximity to the nonlinear loads or the electrical panels feeding them.

Reduction of neutral current and mitigation of third order harmonics reduce the heat produced in the transformer

upstream of the CTT, and as a result the available kVA of the transformer is increased.

The CTT's capability of reducing the voltage distortion facilitates conformity with IEEE 519. CCT products are

related according to their neutral current reduction capability; For example, a 60 Amp CTT can handle 60 Amp

of neutral current (20 Amp per phase). All connection points of CTT are accessible from the front of the unit. The standard version of CTT has a

maximum temperature rise of 130 °C. The finished product is shipped in a shrink-wrapped, gray NEMA 3R enclosure with corner protectors on our

unique SmartSkid®, for safe and effortless transportation and installation. For more information about

SmartSkid® and its advantages, please refer to the SmartSkid® section of the catalogue.

CT

T is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

Front


Standard Features:

SmartSkid®


Three Phase, Dry, Modified Zig Zag



130 °C

220 °C

Per NEMA ST20

NEMA 3R

Packaging:

Warranty:

Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:



Enclosure Type:

CTT


http://synergyenergyinc.com/Synergy_Energy_Inc_ctt.html



CT

T is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

Voltage: Up to 13800 V

Product: CTT

Rating: 60 for 60 Amp up to 2000 for 2000 Amp of neutral current







Example: CTT with 150 Amps Neutral Current capacity, 480 V, 130 °C Temperature Rise, 60 Hz Frequency in a

Gray NEMA 3R Enclosure

Model Number: CTT-150-480-130-60-N3R-GRY

CTT- NC - V - TEMP - FRQ - ENC - COL




CTT


7654321

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:

http://synergyenergyinc.com/Synergy_Energy_Inc_ctt.html



The VFDS (Variable Frequency Drive Solution) is a harmonic mitigating device

designed specifically to mitigate 5th and 7th harmonics created by three phase

nonlinear loads such as Variable Frequency Drives. It is an efficient, reliable, and

long lasting electromagnetic based device. The VFDS takes advantage of phase shifting technology to mitigate the targeted

harmonics. Harmonics created by one source are canceled by the harmonics

from the other. Reduction of the 5th and 7th harmonics provides cleaner voltage

to the other equipment in the facility, reduces equipment malfunction and failure,

and is an important element of Power Factor.

Power Factor improvements result in increased energy efficiency, reduced

electricity bills, and will facilitate IEEE 519 compliance.

The VFDS is designed to be installed upstream of the nonlinear load and downstream of the Busbar or the

Riser (between the Busbar and the load).

All connection points of the VFDS are accessible from the front of the unit. The standard version of the VFDS

has a maximum temperature rise of 130 °C.




VF

DS

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

Front


Standard Features:

SmartSkid®


Three Phase, Dry, Modified Auto-Poly



130 °C

220 °C

Per NEMA ST20

NEMA 3R

Packaging:

Warranty:

Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:



Enclosure Type:

VFDS


http://synergyenergyinc.com/Synergy_Energy_Inc_vfds.html



VF

DS

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.

Voltage: Up to 25 kV

Product: VFDS

Rating: 9 for 9kVA up to 5000 for 5000 kVA











Example: VFDS with 75 kVA Rating, 480 V, 130 °C Temperature Rise, 60 Hz Frequency, in Gray NEMA 3R Enclosure

Model Number: VFDS-75-480-130-60-N3R-GRY

VFDS - kVA - V - TEMP - FRQ - ENC - COL






VFDS

Additional Options:


7654321

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount


http://synergyenergyinc.com/Synergy_Energy_Inc_vfds.html



HET (High Efficiency Transformer) products are specifically designed with Ultra

High Efficiency to reduce the operating cost of the facilities. HET is the ideal

transformer for supplying power to panels or equipment with high linear load

concentration.

HET is a three-phase isolation transformer and directly replaces a standard

Delta-Wye transformer to deliver one of the shortest periods on returning the

investment when used to feed their appropriate loads.

HET is designed with efficiency levels much higher than what is required by

NEMA TP-1 and CSA 802.2-06 standards and exceeds US DOE CSL-3

efficiency levels. HET efficiency is third party verified by Intertek, one of the most

trusted test organizations in the world. It also bears the Intertek logo for

efficiency together with the related verification number.

HET has 40% lower core loss than a standard Delta-Wye transformer. Core loss (or no-load loss) is the energy

that a transformer uses when it is energized regardless of the amount of load. This means that HET will pay for

itself many times over during its lifetime. HET is also in line with KYOTO accord requirements for reduction of

greenhouse gasses and carry one of the longest warranties in the business.

All the connection points of HET transformers are accessible from the front of the units and they accept a wide

variety of extra options. HET in its standard form has a maximum temperature rise of 130 °C with four primary

voltage taps (Two taps above and two taps bellow nominal).




HE

T is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE

Front


Standard Features:


SmartSkid®



Intertek




130 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Efficiency:


Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:



Enclosure Type:

HET


http://synergyenergyinc.com/Synergy_Energy_Inc_het.html



HE

T is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.



Product: HET









Example: HET with 75 kVA Rating, 480 V Primary, 208/120 V Secondary, 130 °C Temperature Rise,

60 Hz Frequency, 2 Electrostatic Shields, in Gray NEMA 3R Enclosure

Model Number: HET-75-480-208-130-60-2S-N3R-GRY

HET- kVA - PV - SV - TEMP - FRQ - SHLD - ENC - COL




HET


987654321

9

8

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:

http://synergyenergyinc.com/Synergy_Energy_Inc_het.html



HET.K (High Efficiency Transformer-K rated) products are three phase high

efficiency isolation transformers de-rated to the K-rating levels specified by UL.

Typical installation of HET.K would be where non-linear loads are present. The

required K-rating increases with increased amounts of Total Harmonic Distortion

(THD) in the electrical system.

HET.K products offer higher than what is required by NEMA TP-1 and CSA

802.2-06 standards and exceed US DOE CSL-3 efficiency levels.

The efficiency level of HET.K is third party verified by Intertek, one of the most



The basic HET.K is K4 rated but optional rating of up to K40 is available.

HE

T.K

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.

* Warranty: 50 years for HET.K40, 40 years for HET.K30, 30 years for HET.K20, 20 years for HET.K13, 10 years for HET.K9 and 5 years for HET.K4

Sm

art

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE

HET.K transformers have front access to all their connection points (Primary, Secondary, Voltage Taps, Ground

Lugs and also the Electrostatic Shield and Thermal Sensor Terminations if the option is chosen). They accept a

wide variety of extra options. The standard version of HET.K has maximum temperature rise of 150 °C and is

supplied with four primary voltage taps (Two taps above and two taps bellow the nominal voltage).

The finished product is shipped in a shrink-wrapped, gray NEMA 3R enclosure

with corner protectors on our unique SmartSkid® for safe and effortless

transportation and installation. For more information about SmartSkid® and its

advantages, please refer to the SmartSkid® section of catalogue.

Front


Standard Features:


SmartSkid®

50 years* (Pro-Rated)


Intertek




150 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Efficiency:


Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:




Enclosure Type:

HET.K


http://synergyenergyinc.com/Synergy_Energy_Inc_het-k.html



HE

T.K

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.



Product: HET.K4 for K4, HET.K9 for K9, HET.K13 for K13, HET.K20 for K20, HET.K30 for K30 andHET.K40 for K40









Example: 75 kVA HET.K with K Rating of 13, 480 V Primary, 208/120 V Secondary, 150 °C Temperature Rise,


Model Number: HET.K13-75-480-208-150-60-1S-N3R-GRY

HET.K - kVA - PV - SV - TEMP - FRQ - SHLD - ENC - COL




HET.K


987654321

9

8

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:

http://synergyenergyinc.com/Synergy_Energy_Inc_het-k.html



HET.L products are three phase distribution and isolation type of transformers

that perform with higher efficiency and are built to meet or exceed all the

applicable standards of UL, CSA, ANSI, IEEE, and NEMA.

HET.L is the entry level solution to the problem of low efficiency in an electrical

system and is designed to be higher than what is required by NEMA TP-1 and

CSA 802.2-06 standards and exceeds US DOE CSL-3 efficiency levels.

HET.L line of transformers delivers the power quietly and efficiently. HET.L has a

short ROI while it improves the overall efficiency of the facility. HET.L products

meet NEMA ST-20 standard for maximum alowable audible noise level.

The efficiency level of HET.L is third party verified by Intertek, one of the most



HET.L transformers have front access to all their connection points (Primary, Secondary, and Voltage Taps).

HET.L transformers accept a wide variety of extra options. The standard version of HET.L has a maximum

temperature rise of 150 °C with four primary voltage taps (Two taps above and two taps bellow nominal).




HE

T.L is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE

Front


Standard Features:


SmartSkid®

3 years (Pro-Rated)

Intertek




150 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Efficiency:


Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:



Enclosure Type:

HET.L



http://synergyenergyinc.com/Synergy_Energy_Inc_het-l.html



HE

T.L is

a T

rade M

ark

of S

ynerg

y E

nerg

y In

c.



Product: HET.L









Example: HET.L with 75 kVA Rating, 480 V Primary, 208/120 V Secondary, 150 °C Temperature Rise,


Model Number: HET.L-75-480-208-150-60-1S-N3R-GRY

HET.L - kVA - PV - SV - TEMP - FRQ - SHLD - ENC - COL




HET.L


987654321

9

8

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:

http://synergyenergyinc.com/Synergy_Energy_Inc_het-l.html



Front

HE

ST

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

Regis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

C US

CM

L DTSI E

i NTERTEK

CM

V DIRE F i E


VERIFIED


VERIFIE

The HEST (High Efficiency Single-phase Transformer) products provide efficient

power to single-phase loads.

The HEST is designed with two coils and is built to be higher than efficiency

levels of NEMA TP-1 and CSA 802.2-06 and exceed the US DOE CSL-3

standards. The HEST improves the overall efficiency of the facility and returns

the investment in a short period of time. The high efficiency levels of the HEST

will also have a direct impact on improving the Power Factor of the facility,

thereby, reducing the ROI.

Due to the fact that most single-phase transformers are installed outside of the

electrical rooms, close to the equipment and in polluted areas of the work place,

the rugged build of the HEST minimizes the scheduled maintenance intervals to

a minimum, thereby improving the bottom-line.

The efficiency of the HEST is third party verified by Intertek, one of the most trusted test organizations in the

world. It also bears the Intertek logo for high efficiency compliance, together with the related verification number.

All of the connection points of HEST transformers are accessible from the front of the units. They also accept a

wide variety of extra options. The HEST in its standard form has a maximum temperature rise of 150 °C.





Standard Features:


SmartSkid®



Intertek

Single Phase, Dry, Isolation, Common Core



150 °C

220 °C

Per NEMA ST20

NEMA 3R

Primary Taps:

Packaging:

Warranty:

Efficiency:


Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:



Enclosure Type:

HEST


http://synergyenergyinc.com/Synergy_Energy_Inc_hest.html



HE

ST

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.



Product: HEST









Example: HEST with 25 kVA Rating, 480 V Primary, 240/120 V Secondary, 150 °C Temperature Rise,


Model Number: HEST-25-480-240-150-60-1S-N3R-GRY

HEST- kVA - PV - SV - TEMP - FRQ - SHLD - ENC - COL




HEST


987654321

9

8

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:

http://synergyenergyinc.com/Synergy_Energy_Inc_hest.html



The CTT.A is the most economical solution that supplies the most undisturbed

power to the related equipment or area. It is a three phase autotransformer with

natural convection of air as the cooling method.

The CTT.A is designed with low loss core material that results in dramatic drop of

the inrush current. The inrush current of CTT.A is typically between four to six

times its rated primary current. Although autotransformers are not regulated to

meet certain efficiency levels or standards, but Synergy Energy Inc.; as one of

the pioneers of high efficiency dry-type transformers; continues to raise the bar

for all transformer manufacturers in improving their products and designing transformers with lower loss and

higher efficiency. The CTT.A is a perfect example, as the core steel used in its production is of special design;

grain oriented and annealed to provide a high flux density and improve the efficiency.

When compared to a regular autotransformer, the CTT.A offers 30% less no-load losses which puts it amongst

the most efficient products in the industry and a very low period for returning the original investment. Another

advantage of the CTT.A is its small footprint which makes it installation in confined spaces possible. This is

usually the case with imported equipment that require a different operating voltage.

The CTT.A design configuration allows for having a neutral connection point. Therefore, CTT.A can

accommodate any electrical system with 3 phase; 3 wire or 3 phase; four wire on its primary and/or secondary

side. All of the connection points of the CTT.A can be accessed through its removable front panel. It is capable

of accepting a wide variety of additional options.

The CTT.A in its standard form has a maximum temperature rise of 150 °C.




CT

T.A

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.S

mart

Ski

d is

a R

egis

tere

d T

rade M

ark

of S

ynerg

y E

nerg

y In

c.

Front


Standard Features:

SmartSkid®

3 years (Pro-Rated)

Single Phase, Dry, Isolation, Common Core



150 °C

220 °C

Per NEMA ST20

NEMA 3R

Packaging:

Warranty:

Type:

Cooling:

Coils:

Temperature Rise:

Insulation Class:



Enclosure Type:

CTT.A


C US

CM

L DTSI E

i NTERTEK


http://synergyenergyinc.com/Synergy_Energy_Inc_ctt-a.html


CT

T.A

is a

Tra

de M

ark

of S

ynerg

y E

nerg

y In

c.





Primary Voltage: Up to 13.8 kV

Secondary Voltage: Up to 13.8 kV

Product: CTT.A

Rating: 5 for 5 kVA up to 10,000 for 10,000 kVA

Temperature Rise: 150 for 150 °C, 130 for 130 °C, 115 for 115 °C, and 80 for 80 °C


Example: CTT.A with 75 kVA Rating, 480 V Primary, 380 V Secondary, 150 °C Temperature Rise,

60 Hz Frequency, in Gray NEMA 3R Enclosure

Model Number: CTT.A-75-480-380-150-60-N3R-GRY



CTT.A- kVA - PV - SV - TEMP - FRQ - ENC - COL


CTT.A


87654321

8

7

6

5

4

3

2

1

Lug Kit

Thermal Switches

Ground Bar

Ultra Quiet

Over-Current Alarm

Digital Voltmeter

Ceiling Mount








Additional Options:


http://synergyenergyinc.com/Synergy_Energy_Inc_ctt-a.html


As an enviornmnet friendly concept, SmartSkid® utilizes 60% less wood compare to a conventional skid.

®

Environmental Friendly:

By adding only 3" to the depth and 7" to width of the overall dimensions of an enclosure, SmartSkid® is conceptualized to minimize the shipping envelope of a transformer, which in turn minimizes the freight cost.

Lower Freight Cost:

In order to provide the best protection for the most vulnerable sides of the transformer enclosure during transportation, SmartSkid® is designed to take advantage of the maximum lumber strength.

Better Protection in Transit:

Due to lighter structeral design, where only a pallet jack is suffecient for lowering the Transformer with SmartSkid®, the need for utilizing a heavy equipment is eliminated. This unique fature improves the worker's safe by substantial margin.

Safe and Convenient:

Unlike conventional skids, transformer on SmartSkid® may be easily positioned on its installation spot in minutes. According to the conducted studies, depending on the size of the transformer on a conventional skid, SmartSkid will reduce the installation time by 20% to 55%.

Shorter Installation Time:

Regardless of the kVA rating of the transformer, the heavy gauge supporting brackets and their related hardware, which are used to attach the SmartSkid to the enclosure, may be utilized as depicted to suspend the transformer from the ceiling.Note: Threaded rods for ceiling mount are not supplied with the transformer.

Installation Flexibility:

At Synergy Energy Inc., strives for continual improvement along with invaluable customers' feedbacks inspired the design of innovative, unparalleled, and flexible SmartSkid®:

With its versatile and multi-functional design aspects, the revolutionary and unparallel SmartSkid® is to furnish you with the following features and benefits:

EasySkid Brackets are integrated part of the SmartSkid® and are accessible by removing the wooden frame.

EasySkid Brackets may be removed and re-attached to the side of the transformer for ceiling mount purpose.

In conjunction with threaded rods, re-configured EasySkid Brackets may be then utilized to facilitate ceiling mount of the transformer.

Smar

tSkid

is

a Re

gist

ered

Tra

de M

ark

of S

yner

gy E

nerg

y In

c.




Following is to outline the Pro-Rated, and Time-Limited product warranty offered by the Synergy Energy Inc.:

Warranty & Liability

Under the Pro-Rated, and Time-Limited product warranty, Synergy Energy Inc. warrants that its products meet applicable design specifications, and are free from defects in materials and workmanship.

Pro-Rated, and Time-Limited general product warranty measured from the date of shipment of a product is applicable, providing that the product has been utilized in accordance with the storage, handling, installation, operation, and maintenance procedures that has been prescribed by the Synergy Energy Inc.

At the discretion of the Synergy Energy Inc., Pro-Rated, and Time-Limited liability is expressly limited to the repair or replacement of the defective product. Furthermore, the entire liability of the Synergy Energy Inc. shall be limited at the maximum to the purchase price of the product.

Synergy Energy Inc. shall in no way be liable for any consequential damages whatsoever resulting from accidents, improper application, or repair of the product.

The Pro-Rated and Time-Limited warranty offered by Synergy Energy Inc. is in to replace all other preceding warranties sullied by the Synergy Energy Inc., if any.

The Pro-Rated, and Time-Limited offered by Synergy Energy Inc. is governed by the laws of the province of Ontario, Canada.




1. Payment: Synergy Energy Inc. payment terms are "NET 30 DAYS". Synergy Energy will charge interest on overdue accounts at the rate of 2% per month (24% per year). Currency is Canadian dollars.

2. Freight insurance and cartage charges: The purchaser is responsible for freight, insurance and cartage of the order from Synergy Energy Inc.'s place of manufacture or from its warehouse in Toronto (Canada) or New Jersey (USA) unless specifically shown otherwise in writing.

3. Shipping: Upon confirmation of the Purchase Order, Synergy Energy provides a target ship date. This date is an estimate based on the available information at the time of the order and is subject to change.

4. Acceptance: Acceptance of any order is subject to credit approval by Synergy Energy Inc. These terms and conditions form the basis of any acceptance of an order. Any changes are hereby rejected unless approved in writing by Synergy Energy Inc.

5. Price: Prices are applicable for the current order only. Any changes to the order or future order are subjected to possible price changes.

6. Taxes: Any increase or changes in applicable taxes will be passed on by Synergy Energy Inc. and are the responsibility of the customer.

7. Product Return, Order Cancellation: Unless otherwise agreed in writing, returns and cancellations are subjected to a restocking charge. The minimum restocking charge is 20% of the total sales price of the unit(s) and applies to standard products with standard features. Custom built products will have a larger restocking charge. Before returning any product or canceling any order, a written confirmation regarding the restocking charge has to be obtained from Synergy Energy Inc.

8. Product Technical Data: The data published by Synergy Energy Inc. is believed to be accurate at the time of publication, and is subject to change without notice.

9. Technical Advise: Technical advice given is believed to be accurate based on the information provided by the customer. However, Synergy Energy Inc. shall not be liable for technical advice, as it is given to and accepted by the customer at his/her own risk.

10. Force Majeure: Synergy Energy Inc. may cancel an order without liability if conditions arise due to causes beyond its reasonable control, and in no event shall be liable for consequential damage.

11. Risk of Loss: Since the product is sold FOB point of shipment, the customer bears the risk of loss or damage from that point and any loss or damage sustained does not release the customer from the terms of payment or other aspects of these terms and conditions.

12. Title of Goods: Synergy Energy Inc. retains the ownership of the products shipped until payment is made in full.

13. Penalty Clause: A penalty clause is only valid if specifically and separately approved by a Synergy Energy Inc. officer.

14. Clerical Errors: Such errors are subject to correction.

15. Assignment: Prior written consent from Synergy Energy Inc. is required to assign any order and associated obligations.

16. Scope, Changes: This is the entire agreement. Any changes must be approved in writing by Synergy Energy Inc. to take effect.

17. Set Off: Synergy Energy Inc. can set off any amount which is payable by Synergy Energy Inc. to the customer or by the customer to Synergy Energy Inc.

Terms & ConditionsCanada




1. Payment: Synergy Energy Inc. payment terms are "NET 30 DAYS." Synergy Energy will charge interest on overdue accounts at the rate of 2% per month (24% per year). Currency is US dollars.

2. Freight insurance and cartage charges: The purchaser is responsible for freight, insurance and cartage of the order from Synergy Energy inc.'s place of manufacture or from its warehouse in Toronto (Canada) or New Jersey (USA) unless specifically shown otherwise in writing.

3. Shipping: Upon confirmation of the Purchase Order, Synergy Energy provides a target ship date. This date is an estimate based on the available information at the time of the order and is subject to change.

4. Acceptance: Acceptance of any order is subject to credit approval by Synergy Energy Inc. These terms and conditions form the basis of any acceptance of an order. Any changes are hereby rejected unless approved in writing by Synergy Energy Inc.

5. Price: Prices are applicable for the current order only. Any changes to the order or future order are subjected to possible price changes.

6. Taxes: Any increase or changes in applicable taxes will be passed on by Synergy Energy Inc. and are the responsibility of the customer.

7. Product Return, Order Cancellation: Unless otherwise agreed in writing, returns and cancellations are subjected to a restocking charge. The minimum restocking charge is 20% of the total sales price of the unit(s) and applies to standard products with standard features. Custom built products will have a larger restocking charge. Before returning any product or canceling any order, a written confirmation regarding the restocking charge has to be obtained from Synergy Energy Inc.

8. Product Technical Data: The data published by Synergy Energy Inc. is believed to be accurate at the time of publication, and is subject to change without notice.

9. Technical Advise: Technical advice given is believed to be accurate based on the information provided by the customer. However, Synergy Energy Inc. shall not be liable for technical advice, as it is given to and accepted by the customer at his/her own risk.

10. Force Majeure: Synergy Energy Inc. may cancel an order without liability if conditions arise due to causes beyond its reasonable control, and in no event shall be liable for consequential damage.

11. Risk of Loss: Since the product is sold FOB point of shipment, the customer bears the risk of loss or damage from that point and any loss or damage sustained does not release the customer from the terms of payment or other aspects of these terms and conditions.

12. Title of Goods: Synergy Energy Inc. retains the ownership of the products shipped until payment is made in full.

13. Penalty Clause: A penalty clause is only valid if specifically and separately approved by a Synergy Energy Inc. officer.

14. Clerical Errors: Such errors are subject to correction.

15. Assignment: Prior written consent from Synergy Energy Inc. is required to assign any order and associated obligations.

16. Scope, Changes: This is the entire agreement. Any changes must be approved in writing by Synergy Energy Inc. to take effect.

17. Set Off: Synergy Energy Inc. can set off any amount which is payable by Synergy Energy Inc. to the customer or by the customer to Synergy Energy.

Terms & ConditionsUSA




The products designed and manufactured by Synergy Energy Inc. undergo one of

the most stringent, multilevel, computer controlled Quality Control systems in the

industry, where the bar-coded system virtually prevents any human error.

Furthermore, prior to installing a product received from the Synergy Energy Inc., as

a coherent step, it is recommended to verify the technical specification of the

product marked on its label against the ones outlined by your technical team.

Otherwise, following is to outline the twofold Product Return Policy offered by the

Synergy Energy Inc.:

Generally, any return of the product to Synergy Energy Inc. is governed by the

following procedure:

It is important to consider that products, which have been in the client's possession

longer than six months from the Synergy Energy Inc. ship date, are considered

Non-Returnable.

Due to error on client's behalf in ordering the right product, should a deviation

be discovered, it is strongly recommended to contact our team of expert at the

Synergy Energy Inc. and consult our expertise for the best suited action.

Should a return of the product be recommended as the only viable option, the

total cost of the freight for returning of the product to Synergy Energy Inc.

manufacturing site and return of the correct product to the client, is to be

undertaken by the client. Furthermore, in such case, a re-stocking fee may be

applicable and charged by the Synergy Energy Inc.

Under the rare condition, where an incorrect product is forwarded to the client,

Synergy Energy Inc. accepts full responsibility for replacing the product with

the correct type. In this regard, although Synergy Energy Inc. will absorb the

related freight charges for both return of the product to its manufacturing site

and receipt of the replacement product at the client's facility, it will not be liable

or responsible for uninstalling cost of the incorrect product or reinstalling

charges of the replacement product.

Contact Synergy Energy inc. to obtain a RGA (Return Goods Authorization)

number.

Fill out the RGA (Return Goods Authorization) form ensuring to specifically

include the RGA Number and the reason for the return.

Product Return Policy




© Synergy Energy Inc. All Rights Reserved.

Synergy Energy Inc.

Unit 9 - 3182 Orlando Drive

Mississauga, Ontario, L4V 1R5, Canada

Toll free tel: 1-866-866-5822

Toll free fax: 1-866-866-5716

[email protected]

www.SynergyEnergyInc.com

SynergyEnergy

Transformers for the 21st century

2010 Edition





mailto:[email protected]

Synergy Unit 9 - 3182 Orlando Drive Energy - Intellivex - Product_Catalogue_2010.pdf · Unit 9 -...

Documents

Transcript of Synergy Unit 9 - 3182 Orlando Drive Energy - Intellivex - Product_Catalogue_2010.pdf · Unit 9 -...