SWFcontract Drapery Hardware Specification...

SWFcontract Drapery Hardware Specification Guide

3Call 800-327-9798 or email [email protected] swfcontract.com

GRABER® DRAPERY HARDWARE TABLE OF CONTENTS

Pleating Systems ..................................................................... 4Stack Pleat, Roll Pleat, Pinch Pleat

Contrack® Drapery Hardware ......................................................... 5Overview

Made-to-Measure Rods .................................................................. 69-804 Cord Draw

Made-to-Measure Rods .................................................................. 79-808 Hand or Baton Draw

Made-to-Measure Rods .................................................................. 89-8191/9-8091 Baton Draw

Super Duty Slimline Drapery Hardware .......................................... 9

Super Duty Slimline Series ...................................................... 10-119-650 Cord Draw & 9-657 Baton Draw

Made-to-Measure Rods ................................................................ 129-200 Track Series

Made-to-Measure Rods ................................................................ 139-300 Track Series

Cut-to-Measure Rods ................................................................... 149-400 Oval Rodding

Cut-to-Measure Rods ................................................................... 159-600 Solid Steel rodding


GRABER® PLEATING SYSTEMS

Stack PleatDesigned for maximum glass exposure when draperies are open, stack pleat requires half the space of conventional pleated draperies. The snap tape attachment system reduces installation time and simplifies maintenance. Snaps detach with 4 lb. “peel" action and release with 22 lb. “shear" pull. Front and back pleating eliminates bulky appearance. For drapery up to 54" in length, 7½" tape is recommended; 8½" tape is recommended on draperies over 54". Use Graber Slimline or Super Duty architectural drapery hardware, cord or baton draw systems.

Roll PleatThe roll pleat system affords a soft, rounded pleating pattern. Widely used in hospitality and healthcare applications where a residential appearance is desired. A 7/8" nylon snap tape with 4¼" on center snaps is sewn into the header suspended directly under the track to prevent sagging and tipping. Spaced carriers (rolling or sliding) are used to control drapery fullness. Draperies snap off track easily for cleaning and maintenance. Use Graber Slimline or Super Duty architectural drapery hardware, cord or baton draw systems.

Pinch PleatDesigned to provide an elegant, sophisticated look, the pinch pleat header is well suited for either custom or ready made commercial drapery applications. Pinch pleating is compatible with Graber Contrack and Slimline architectural drapery hardware and adjustable traverse rods.


Track # and Traverse Material Mounting Applications Max. Fabric Weight Brackets Max. Track Length

Bending Limits

9-804 Cord Extruded 6063-T5Anodized Satin-Finish Aluminum Aluminum Association Specification No. AA-C22A21 Aluminum thickness .050”

TW draw - 210 lb.OW draw - 140 lb.Mult. draw - 420 lb.

5 lb./ft. rating

Space brackets 48” apart except at ends - then 24” and 48” apart over balance. Wall mount projection for 3” plus ceiling mount available.

TW draw - 42’OW draw - 28’Mult. draw - 84’

Continuous curve or any angle bend on 12” radius - maximum 90˚.No reverse curve.

9-808Hand/Baton

Extruded 6063-T5 Anodized Satin-Finish Aluminum Aluminum Association Specification No. AA-C22A21 Aluminum thickness .050”

TW draw - 240 lb.OW draw - 120 lb.

5 lb./ft. rating

Track punched 16” on center for direct to ceiling mount with screws.

TW draw - 48’OW draw - 24’

12” radius regular and reverse curves, can be continuously curved.

9-8191/9-8091*Hand/Baton

Extruded 6063-T5 Aluminum in White Painted FinishAluminum Association Specification No. AA-C22A21 Aluminum thickness .050”


5 lb./ft. rating

Snap-in ceiling clips are available for ceiling mount. Track can also be drilled in field for direct screw mount. For wall mount, space brackets 48” apart except at ends - then 24" and 48" apart over balance. Projections from 3½" to 4-1/4".


Can be bent to any angle on 12” radius, maximum 90˚. No continuous or reverse curves.

GRABER® CONTRACK® DRAPERY HARDWARE

The most versatile aluminum pinch pleat system in today’s market. Graber Contrack sets the standard in heavy duty aluminum drapery hardware tracks for pinch pleat drapery. Rolling and sliding carriers are forward canted for erect headings. Available in a variety of systems with ball bearing carriers. Graber Contrack can offer the widest range of applications to fit any heavy duty situation.

Contrack Drapery Hardware Selections and Performance Data(TW = Two-way, OW = One-way, Mult. = Multiple Draw)

All systems are for conventional pinch pleat draperies. Custom painting available upon request.*Aluminum silver finish 9-8091 is available as a special order with a minimum quantity of 2500 ft.

7/8"

11/16"11/16"

7/8"

1 3/8"

7/8"

11/16"

1 3/8"

11/16"

7/8"

15/16"

1 1/4"1-1/4"

15/16"


9-819Ball Bearing Master Carrier of 9-804

9-840 Ball Bearing Carrier9-849 Ball bearing Carrier w/hook9-861 Economy Slide

All are compatible with 9-804, 9-808 & 9-8191/9-8091

9-823Ball Bearing Pulley Set for 9-804

9-856Splice for 9-804

9-826Ball Bearing Insert Pulley for 9-804

9-860Ceiling Bracket for 9-804

8-648Metal Cord Tension Pulley Ball Bearing

9-862Heavy Duty Wall Bracket3" projection

9-865Heavy Duty Double Bracket3" and 6" projection

Specifications

9-804 Heavy duty, wall or ceiling mount, cord traverse, pinch pleatCarriers and cord operate in separate channels for smooth, heavy duty operability. 9-804 can be mounted to the wall using heavy duty aluminum brackets. Ceiling mount brackets are also available.

GRABER® CORD TRAVERSE CONTRACK® SERIES

1. Track: furnish and install, as indicated on plans, Graber Contrack 9-804 extruded .050" thick dual channel anodized satin-finish aluminum drapery track in accordance with AA Specification C22A21.

2a. Components: For two-way draw, specify: 9-819 ball bearing masters 9-823 ball bearing pulley sets 8-648 ball bearing cord tension pulley 9-039 #5 nylon cord with fiberglass core 9-840 ball bearing master carriers Also available: 9-849 ball bearing carrier with hook 9-861 economy slide

2b. Components: for one-way draw, specify: 9-820 reversible ball bearing master carrier 9-823 ball bearing end pulley 9-826 insert pulley Plus track, carriers, cord and pulleys mentioned above

3. Brackets: Specify 9-862 (3" wall mount projection) 9-865 (3" and 6" wall mount projection) 9-860 bracket for ceiling mount

15/16"

1 1/4"

Major Components

Call 800-327-9798 or email [email protected] swfcontract.com

7

9-821Ball Bearing Master Carrier two way for 9-808 & 9-8191

Fiberglass Baton with clip33" 8-637-148" 8-638-1 60" 8-639-1

9-822Ball Bearing Master Carrier, reversible one way for 9-808 & 9-8191

9-165End Stop for 9-808 & 9-8191

9-710 - Right9-171 - LeftReturn Extender for 9-808 & 9-8191

9-861 Economy Slide9-840 Ball Bearing Carrier for 9-804, 9-808 & 9-81919-849 Ball Bearing Carrier with hook for 9-808

9-857Splice for 9-808

GRABER® HAND TRAVERSE CONTRACK® SERIES

9-808 Hand draw, ceiling mount, pinch pleat

9-808 is the perfect choice for recess applications and tight curves both regular and reverse. Ball bearing carriers and economy slide carriers are available. (Mounting holes punched 16" on center for ceiling installation).

This heavy duty ceiling mounted track system is ideal for curved drapery applications. The 9-808 system also serves as a heavy duty cubical track for hospital applications. Erect drapery headings are assured by the forward canted non-binding ball bearing carriers. Perfect for recessed applications and tight curves, this track system has a durable metal baton arm.

Specifications

Major Components

1. Track: Furnish and install, as indicated on plans. Graber Contrack 9-808 extruded .050" thick anodized satin-finish aluminum drapery track in accordance with AA Specification C22A21.

2a. Components: For two-way draw, specify: 9-821 ball bearing master carriers (pair) 8-637-1 (33") fiberglass batons 9-840 ball bearing carriers 9-165 end stops Also available as options: 9-849 ball bearing carrier with hook 9-861 economy slide

9-171 left and 9-170 right return extenders

2b. Components: For one-way draw, specify: 9-822 ball bearing reversible master carrier with baton arm, baton, carriers and end stops mentioned above.

3. Mounting: Mounting holes punched 16" on center for direct screw ceiling installation.

4. For deluxe cubicle, specify: 9-808 track 9-849 ball bearing carrier with hook 9-165 end stops

Features


9-821Ball Bearing Master Carrier two way for 9-808 & 9-8191

9-861 - Economy Slide

9-822Ball Bearing Master Carrier, reversible one way for 9-808 & 9-8191

8-637-1 - 33" Fiberglass Baton with clip8-638-1 - 48" Fiberglass Baton with clip

9-165End Stop for 9-804, 9-808 & 9-8191

9-957 - Wall Bracket

9-170 - Right9-171 - LeftReturn Extender for 9-808 & 9-8191

9-955 - Ceiling Bracket

9-840Ball Bearing Carrier for 9-804, 9-808 & 9-8191

9-850 - Splice

GRABER® MADE TO MEASURE ROD SPECIFICATIONS

9-8191 / 9-8091 Track SeriesThe most versatile aluminum pinch pleat system in today’s market for baton draw applications, ideal for use in hotels and healthcare. Graber Contrack sets the standard in heavy duty aluminum drapery hardware tracks for pinch pleat drapery. Ball bearing and slide carriers are forward canted, providing for aesthetic fabric installation.

1. Track: Furnish and install, as indicated on plans, Graber 9-8191 extruded .050" thick track in a white painted finish in accordance with AA Specification C22A21.

2a. Components: for two-way draw, specify: 9-821 ball bearing master carriers with adjustable

baton arm (assembled in down position) 8-637-1 (33") fiberglass baton 9-840 ball bearing carriers 9-165 end stops Also available as options: 9-824 ball bearing master carrier with adjustable

baton arm (assembled in up position) 9-849 ball bearing carriers with hook 9-861 economy slide 9-171 left and 9-170 right return extenders

2b. Components: For one-way draw, specify: 9-822 ball bearing reversible master carrier with

adjustable baton arm (assembled in down position) with baton, carriers and end stops indicated above

Also available as an option: 9-831 ball bearing master carrier with adjustable baton

arm (assembled in up position) Brackets: For ceiling mount, specify: 9-955 snap-in ceiling bracket Track may also be drilled in field for direct screw mount For wall mount, specify: 9-957 wall bracket

9-8191 Hand draw, ceiling or wall mount, pinch pleat9-8191 is an excellent heavy duty ceiling or wall mounted track system. Economical and easy to install, the 9-8191 is compatible with our snap-in ceiling bracket, or can be direct screw mounted. Available with ball bearing wheeled carriers or economy slide carriers, the 9-8191 comes standard in a white painted finish. Under special order, this track is also available in an anodized satin finish under part number 9-8091 with a minimum order quantity of 2500 ft.

Baton draw Contrack® rod systemIdeally suited to upgrade drapery hardware system using existing draperies.

1 3/8"

7/8"

11/16"

Molded end cap cleanly finishes end of track.

Over the drapery baton attachment to simplfy drapery removal and installation.

Overlapping heavy duty master arms eliminate light gaps.

Forward canted rolling carriers for erect drapery heading

Specifications

Major Components

9

Track # and Traverse Material Mounting Applications Max. Fabric Weight Brackets Max. Track Length Bending Limits

9-650 Cord Traverse

.060" wall

Anodized aluminum in natural or white baked enamel.

Track thickness .060"


2.5 lb./ft. rating

Projection from 3½" to 4½" plus ceiling mount.


Can be continuously curved to any angle using 12" radius. Reverse curving not available.

9-657 Baton Traverse

.060" wall

Anodized aluminum in natural or white baked enamel.

Track thickness .060"


2.5 lb./ft. rating

Projection from 3½" to 4½" plus ceiling mount.


Can be bent and reverse curved to any angle using 12" radius. Continuous curving not available.

GRABER® SLIMLINE SUPER DUTY DRAPERY HARDWARE

Product Features

Graber Super Duty Slimline systems offer the most diverse aluminum drapery hardware available today for the alternate pleating systems (roll, pinch and stack pleat). Heavy duty provides the only wheeled system available for alternate pleats. Combined, these can satisfy a wide variety of drapery hardware requirements and applications. Especially popular for recess mounting applications and heavy drapery requirements. Super Duty Slimline can prove to be a valuable energy and cost saver without resorting to bulky, expensive stage or special application tracks. Specify Graber Super Duty Slimline for your snap tape drapery hardware requirements.

Super Duty Slimline Drapery Hardware Selections and Performance Data(TW = Two-way, OW = One-way)

NOTE: Super Duty Slimline drapery tracks can be used with pinch pleat drapery if #9-396 horseshoe clips are used to lock the pendants (9-345) onto the sliding or rolling carriers (two-piece snap-in carriers). One-piece sliding carriers 9-342 and 9-450 also can be used for pinch pleat draperies. Round overhead pins (pinned at the top of the drapery) also are recommended.


9-351End Pulley left hand9-350End Pulley right hand

9-358Track Splice

9-356Left Hand Butt Master9-357Right Hand Butt Master

9-360Ceiling Bracket

9-353End Pulley Housing

9-381 Connected Rolling Swivel Carriers (80% fullness)9-382 (100% fullness)9-395 (120% fullness)

8-648Metal Cord Tension Pulley Ball Bearing

9-345Swivel Snap Pendant9-383Rolling Carrier

9-354Underlap Master Left Hand9-355Overlap Master Left Hand

9-396Horseshoe Clip Specify for Pinch Pleat

9-359Adjustable Wall Bracket

9-650 Series, super duty, cord draw for roll, stack and pinch pleat systemsOur Super Duty slimline series track systems provide added strength for the heaviest draperies and extra wide openings. Ball bearing end pulleys and wheeled carriers provide a smooth cord draw operation.

GRABER® SUPER DUTY SLIMLINE SERIES

1. Furnish and install as indicated on plans, Graber 9-650 Super Duty Slimline dual channel .060" thick anodized aluminum track.

2a. Components: For two-way draw, specify: 9-350 right and 9-351 left ball bearing end pulleys 9-355 right overlap master carrier* 9-354 left underlap master carrier* 8-648 ball bearing cord tension pulley 9-040 #4 nylon cord with fiberglass core 9-383 unconnected rolling swivel carrier (for stack and pinch pleat) 9-381 connected rolling swivel carrier (for roll pleat, 80% fullness) 9-382 connected rolling swivel carrier

(for roll pleat, 100% fullness) 9-395 connected rolling swivel carrier (for roll pleat, 120% fullness) 9-345 swivel snap pendant2b. Components: For one-way draw, specify: 9-350 right or 9-351 left ball bearing end pulley 9-353 ball bearing one way end pulley 9-355 right or 9-354 left hand master plus tension

pulley, cord and carriers as indicated above

3. Brackets: Specify:for wall mount, 9-359 adjustable wall bracket (3½" - 4½" projection) for ceiling mount, 9-360 ceiling bracket

*Also available: 9-357 right and 9-356 left butt masters

Specifications

Major Components


9-381 Connected Rolling Swivel Carriers (80% fullness)9-382 (100% fullness)9-395 (120% fullness)

9-383 - Rolling Carrier unconnected without pendant9-384 - Gralon Rolling Carrier unconnected with pendant9-345 - Swivel Snap Pendant

9-379Adjustable Cam Bracket

9-387 - Master Carrier right hand

9-385Drapery Return Snap Plate

9-391 - Ceiling Bracket

9-386End Cap Assembly

9-850 - Track Splice

8-637-1 - 33" Fiberglass Baton with Clip8-638-1 - 48" Fiberglass Baton with Clip8-639-1 - 60" Fiberglass Baton with Clip

9-396 - Horseshoe Clip

9-388Master Carrier left hand

9-404 - Double Bracket Base (optional)

9-461-1Snap Tape 4¼" On Center; Low Pull Force

9-463-1 - Snap Tape 4¼" On Center; High Pull Force

9-657 Series, super duty, hand (baton) draw for roll, stack and pinch pleat systems

Like the 9-650 cord draw system, the 9-657 Super Duty Slimline track system provides added strength and smooth operation for the heaviest draperies, with baton draw operation.

MADE TO MEASURE ROD SPECIFICATIONS

1. Track: Furnish and install, as indicated on plans Graber 9-657 super duty flanged channel .060" thick anodized aluminum track. Specify finish, natural aluminum or white.

2a. Components: For two-way draw, specify: 9-387 right and 9-388 left hand master carriers 9-386 end caps 9-385 return snap plate 8-637-1 (33") fiberglass baton 9-383 unconnected rolling swivel carrier (for stack and pinch pleat) 9-381 connected rolling swivel carrier (for roll pleat, 80% fullness) 9-382 connected rolling swivel carrier

(for roll pleat, 100% fullness) 9-395 connected rolling swivel carrier (for roll pleat, 120% fullness) 9-345 swivel snap pendant

2b. Components: For one-way draw, specify: 9-387 right or 9-388 left master carrier plus end caps,

return plate, baton and carriers as indicated above

3. Brackets: Specify: for wall mount, 9-379 adjustable wall bracket

(3½" - 4½" projections) for ceiling mount, 9-391 ceiling bracket

Specifications

Major Components


1/2"

1"

9-200Heavy Duty

A strong, versatile rodding with a wide choice of companion parts. Precision formed steel rodding with oil free polyester finish.

White (1)

One way operation: 22 lb.Two way operation: 35 lb.

Bracket 1-7/8" - 2-7/8"Projection 2-1/2" - 4-1/4" - standard 5" - 6-1/2"

Maximum Length 16 ft.

GRABER® MADE TO MEASURE ROD SPECIFICATION

9-200 Series

Graber Made-to-Measure Tracks, Heavy Duty and Signet are of the finest quality drapery hardware. Rolled of generous gauge steel, durable oil-free polyester finish, ball bearing pulleys with oversize wheels for continuous smooth operation. Compact pulley housings for close side stacking of drapes.

9-200 Heavy Duty Series: Furnish and install as indicated on plans, Graber 9-200 Heavy Duty Steel .0279 roll formed rodding in a white oil free polyester finish. Includes the following components: 9-105 Adjustable Master Slides, 9-213 Ball Bearing Pulley set, 9-346 Conventional Slides, 8-655 Molded Cord Tension Pulley, 9-041 #4 nylon cord with Fiberglass Core, 9-231 Center Supports and 9-125 End Brackets.

One-Way Left / One-Way Right 9-200 track using 9-213 Pulley Set and 9-212 End Pulley with 9-108 Master, 9-346 Slides, 9-041 #4 Traverse Cord, 8-655 Tension Pulley, 9-231 Center and End Supports, one 9-125 Bracket.

ADVANTAGES:These sets feature ball bearing pulleys with oversize wheels and compact pulley housings for close drapery stacking, front loading end brackets, metal adjustable master carrier arms, and spring loaded slide gate.

Specifications


GRABER® MADE TO MEASURE ROD SPECIFICATIONS

3/8"

3/4"

9-300Heavy Duty

A popular general purpose steel rodding for installations of average weight and width. Features versatility plus economy with a full selection of parts and accessories. Oil free polyester finish.

White (1)

One way operation: 20 lb.Two way operation: 35 lb.

Bracket 1-7/8" - 2-7/8"Projection 2-1/2" - 4-1/4" - standard 5" - 6-1/2"

Maximum Length 16 ft.

9-300 Series

Graber Made-to-Measure Tracks, Heavy Duty and Signet are of the finest quality drapery hardware. Rolled of generous gauge steel, durable oil-free polyester finish, ball bearing pulleys with oversize wheels for continuous smooth operation. Compact pulley housings for close side stacking of drapes.

9-300 Signet Series: Furnish and install as indicated on plans Graber 9-300 Regular Duty steel .0279" roll formed rodding in a white oil-free polyester finish. Includes the following components: 9-310 Master Slides, 9-313 Pulley Set, 9-346 Conventional Slides, 8-655 Molded Cord Pulley, 9-042 #3¼ Nylon Cord with Fiberglass Core, 9-331 Center Support and 9-125 End Brackets.

One-Way Left / One Way Right 9-300 track using 9-313 Pulley set and 9-316 End Pulley with 9-312 Master, 9-346 Slides, 9-042 #3¼ Traverse Cord, 8-655 Tension Pulley, 9-331 Center and End Supports, one 9-125 End Bracket.

ADVANTAGES:These sets feature nylon end pulleys with oversize wheels and compact pulley housings for close drapery stacking, spring-loaded slide gate, front load end brackets, and metal adjustable master carrier arms.

Specifications


11/32"

9/16"

9-400

9-415

A durable, economical rodding system for draperies and curtains. Available in 9 and 12 foot lengths.

White (1)Brackets:9-408-1 Inside bracket9-409-1 Sash ¾”rojection9-413-0 Push-on bracket4-808-0 Single outside bracket4-809-0 Double outside bracket

White (1)Zinc Chromate (0)

Center Support:9-419-0 Ceiling Drop9-420-0 1-1/8" Ceiling Drop9-421-1 Projects 2"-3"9-423-1 Projects 3.5"-5"9-425-1 Projects 3"-7"9-427-1 Projects 6"-10"

White (1)Zinc Chromate (0)

9-401-1 Reversible 9-403-1 Elbows9-405-1

GRABER® CUT TO MEASURE ROD SPECIFICATIONS

9-400 Oval Rodding

Graber Oval Rodding is ideal for drapery, curtain and valance applications. The rodding is roll formed from 0.0279” thick steel and is finished with a white polyester paint finish. Reversible Elbows are available for a wide range of treatments with 6 different return projections.

9-400 Oval Rodding: Furnish and install as indicated on plans. Graber 9-400 Oval Rodding roll formed from 0.0279" thick steel with an oil free white polyester finish. For widths greater than 12 feet use splice part number 9-415-1. Choose from appropriate installation brackets and Reversible Elbows. Elbows have the following projections; 9-401-1 (1¾” and 2¾”), 9-403-1 (3¾” and 4¾”), 9-405-1 (5¾” and 6¾”). Choose appropriate Intermediate Support Bracket based on projection.

Specifications


GRABER® CUT TO MEASURE ROD SPECIFICATIONS

9-600 Solid Steel Rodding

Graber Solid Steel Rodding is designed for use with heavier weight drapery fabric or drapes with blackout liners. They are also an excellent choice for hanging large banner displays. The steel rodding is ³/8” thick with a brass finish and is available in lengths up to 12 feet.

3/8"

9-600

3/8” Solid round rodding is strong and versatile. Available in 12-foot lengths in a brass finish. Easy to cut to desired size.

Brass (8)

9-604-8 Gooseneck bracket with 1” projection.

9-615-8 Outside mount barrel bracket with 3/8” projection.

9-612-8 Inside mount barrel bracket.

9-600 Solid Steel Rodding: Furnish and install as indicated on plans. Graber 9-600 Solid Steel Rodding, ³/8” thick with a brass finish. Select bracket for desired installation; 9-604-8 Gooseneck Bracket with 2” projection, 9-615-8 Outside Mount Barrel Bracket with ³/8” projection or 9-612-8 Inside Mount Barrel Bracket.

Specifications

21-5986-07 (11/12) 122497

SWFcontract Drapery Hardware Specification...

Documents

Transcript of SWFcontract Drapery Hardware Specification...