SUNBEAM ALPINE COOLING KIT - Revotec Ltd · 2016. 4. 19. · SUNBEAM ALPINE COOLING KIT 070060 VERY...
1
Revotec Ltd, Unit A, The Croft, Hithercroft Industrial Estate, Wallingford, Oxfordshire, OX10 9RG Tel: 0044 (0) 1491 824424 Fax: 0044 (0) 1491 833711 Email: [email protected] www.revotec.com SUNBEAM ALPINE COOLING KIT 070060 VERY IMPORTANT NOTE This Revotec Cooling Kit has been engineered to provide perfect cooling for your Alpine. However it is essential the other components of the cooling system are operating correctly. The following must be checked: 1. The Radiator has a normal life expectancy of approx 8-9 Years after this time It should be thoroughly assessed and any signs of deterioration such as furring up internally or out of shape it is recommended it is replaced. 2. The Radiator fins Must be clear of all debris such as mud and leaves. 3. The system Must be filled with Correct Coolant. 4. The Water Pump and thermostat must be operating correctly. 1. Disconnect +ve battery terminal, drain the water system and remove the top and bottom hoses from the radiator, remove the four radiator mounting bolts and lift the radiator out of the car, then remove the original mechanical fan and refit the original bolts into the water pump pulley. 2. For each fan push the 2 flush mounts (FM225) through the left and right mounting lugs on the cooling fan and lay it down on the bench, next slide the 4 plastic spacers onto the flush mounts (Note: We have supplied 2 different length spacer sets due to the variation in core thickness, the fans must be as close to the core as possible without touching), space the fans apart and lay the top and bottom fan brackets over the protruding studs and fasten the assembly in place with the included M6 washers and nuts (Fig.1). 3. With the assembly positioned with the with the taller of the brackets at the bottom (Fig. 2) lay the assembly over the radiator and slide in position lining up the bolt holes (Fig.3). Holding both the radiator and brackets together (an extra pair of hand may be required) gently lower the assembly into position in the car and fasten using your original radiator mounting bolts. 4. Position the fan controller in a suitable place in the top hose, refill the water system, connect the fans in parallel as Fig.4 and follow Electronic Fan Controller instructions for information on wiring and setup. Fig.4 Fig.1 Fig.2 Fig.3
Transcript of SUNBEAM ALPINE COOLING KIT - Revotec Ltd · 2016. 4. 19. · SUNBEAM ALPINE COOLING KIT 070060 VERY...
-
Revotec Ltd, Unit A, The Croft, Hithercroft Industrial Estate, Wallingford, Oxfordshire, OX10 9RG Tel: 0044 (0) 1491 824424 Fax: 0044 (0) 1491 833711 Email: [email protected] www.revotec.com
SUNBEAM ALPINECOOLING KIT 070060
VERY IMPORTANT NOTEThis Revotec Cooling Kit has been engineered to provide perfect cooling for your
Alpine. However it is essential the other components of the cooling system are operating correctly. The following must be checked:
1. The Radiator has a normal life expectancy of approx 8-9 Years after this time It should be thoroughly assessed and any signsof deterioration such as furring up internally or out of shape it is recommended it is replaced.
2. The Radiator fins Must be clear of all debris such as mud and leaves.3. The system Must be filled with Correct Coolant.
4. The Water Pump and thermostat must be operating correctly.
1. Disconnect +ve battery terminal, drain the water system andremove the top and bottom hoses from the radiator, remove the fourradiator mounting bolts and lift the radiator out of the car, thenremove the original mechanical fan and refit the original bolts intothe water pump pulley.
2. For each fan push the 2 flush mounts (FM225) through theleft and right mounting lugs on the cooling fan and lay it down onthe bench, next slide the 4 plastic spacers onto the flush mounts(Note: We have supplied 2 different length spacer sets due to thevariation in core thickness, the fans must be as close to the core aspossible without touching), space the fans apart and lay the top andbottom fan brackets over the protruding studs and fasten the assembly in place with the included M6 washers and nuts (Fig.1).
3. With the assembly positioned with the with the taller of thebrackets at the bottom (Fig. 2) lay the assembly over the radiatorand slide in position lining up the bolt holes (Fig.3). Holding both theradiator and brackets together (an extra pair of hand may berequired) gently lower the assembly into position in the car and fasten using your original radiator mounting bolts.
4. Position the fan controller in a suitable place in the top hose,refill the water system, connect the fans in parallel as Fig.4 andfollow Electronic Fan Controller instructions for information on wiringand setup.
Fig.4
Fig.1
Fig.2
Fig.3
