SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... ·...

43
SUBMITTAL DATA Vers. 4_13

Transcript of SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... ·...

Page 1: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

SUBMITTAL DATA

Vers. 4_13

Page 2: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

LOOP FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Choking around bar joists, purlins, beams, roof trusses, strut, and other accessible building

features.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Crimp/Ferrule: Aluminum

No.1 No.2 No.3 No.4 No.5

Cable Diameter (in.) 1/16 5/64 1/8 3/16 1/4

Strand configuration 7x7 7x7 7x7 7x19 7x19

Min. breaking load (lbs) 125 500 1,000 2,475 3,575

Max. safe working load (lbs) 25 100 200 495 715

Tensile strength (lbs/sq. in.) 256,700 256,700 256,700 256,700 256,700

Cable with crimped loop end fixing:

Gripple Fastener:

Sizes: No.1-No.5

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

No.4 495 lbs

No.5 715 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

A (in.)

(approx.)

B (in.)

(approx.)

C (in.)

1 3/16” 2 3/8” 3/8”

1 3/16” 2 3/8” 1/2”

D (in.)

1/4”

5/16”

No.1

No.2

No.3 1 3/16” 2 3/8” 5/8” 3/8”

No.4 1 3/4” 3 1/4” 1” 5/8”

No.5 1 3/4” 3 1/2” 1 3/16” 3/4”

Spiral Duct, Small Choke

Spiral Duct, Large Cradle

Light Fixture with V-Bracket

Ceiling Attachment

with Ceiling Clip

A

C

B

D

Page 3: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

LOOP-TOGGLE FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Drill or punch hole through deck, and drop hanger down through hole prior to concrete pour.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Crimp/Ferrule: Aluminum

Toggle Plate: Zinc Plated Steel

No.2 No.3

Cable Diameter (in.) 5/64 1/8

Strand configuration 7x7 7x7

Min. breaking load (lbs) 500 1,000

Max. safe working load

(lbs)

100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

Cable with crimped loop end fixing and toggle:

Gripple Fastener:

Sizes: No.2-No.3

Max. Safe Working Loads: No.2 100 lbs

No.3 200 lbs

Size A B

No.2 4 1/2” 1 5/8”

No.3 4 1/2” 1 5/8”

A B

Concrete media

Application Example Size Specs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Page 4: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

STUD - 1/4” and 3/8” FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Concrete structures, metal decking, metal brackets using nuts, and clamps & clevis hangers. 1/4”

stud works with a 1/4” anchor, and 3/8” stud works with a 3/8” anchor. Can also be used with

internally threaded concrete inserts. 1/4” stud available with 1” or 2” thread.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Stud End: Zinc plated steel

No.2 No.3 No.4

Cable Diameter (in.) 5/64 1/8 3/16

Strand configuration 7x7 7x7 7x19

Min. breaking load (lbs) 500 1,000 2,475

Max. safe working load (lbs) 100 200 495

Tensile strength (lbs/sq. in.) 256,700 256,700 256,700

No.1

1/16

7x7

125

25

256,700

Cable with crimped 1/4” or 3/8” stud end fixing:

Gripple Fastener:

Sizes: 1/4” - No.1-No.3 (1” thread)

No.2-No.3 (2” thread)

3/8” - No.2-No.4

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

No.4 495 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size A (in.) B (in.) C (in.)

No.1 1/4” 1” 2”

No.2

1/4” 1” 2”

1/4” 2” 4”

3/8” 1 7/8” 2 3/4”

1/4” 1” 2”

1/4” 2” 4”

3/8” 1 3/4” 3 3/4”

No.4 3/8” 1 3/4” 3 3/4”

No.3

Size Specs

A

C

B

Application Examples

Spiral Duct Stud up

Track Lighting Stud down

Cable Basket Stud up

Page 5: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

TOGGLE

FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Inserts into specific hole diameters of light fixtures, metal decking, and other pre-drilled structures

or services. Toggle sizes available to fit 1/4”, 5/16”, 3/8”, and 1/2” hole sizes.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Toggle Plate & End Stop: Zinc plated steel

No.1 No.2 No.3

Cable Diameter (in.) 1/16 5/64 1/8

Strand configuration 7x7 7x7 7x7

Min. breaking load (lbs) 125 500 1,000

Max. safe working load (lbs) 25 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700 256,700

No.4

3/16

7x19

2,475

495

256,700

Cable with end stop and toggle plate:

Gripple Fastener:

Sizes: 1/4” - No.1-No.2

5/16” - No.2

3/8” - No.3

1/2” - No.4

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

No.4 495 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

B A

C

E

D

Size A (in.) B (in.) C (in.) D (in.) E (in.)

No. 1 1/4” 5/32” 5/16” 7/32” 1 9/16”

No. 2 5/16” 1/4” 15/32” 5/16” 1 9/16”

1/4” 1/4” 15/32” 1/4” 1 9/16”

No. 3 3/8” 1/4” 3/4” 3/8” 2”

No. 4 1/2” 11/32” 1 3/16” 15/32” 2 17/32”

Size Specs Application Examples

Spiral Duct Toggle up, via hole

drilled in metal deck

Light Fixture Toggle down

Page 6: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

HOOK & MINI HOOK FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Beam & purlin clips, cable basket & tray, light fixtures, or any service or clip with a 1/4” hole.

Attachment to top rail of cable basket or tray should be per basket/tray manufacturer’s approval.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Hook End: Zinc plated steel

No.1 No.2 No.3

Cable Diameter (in.) 1/16 5/64 1/8

Strand configuration 7x7 7x7 7x7

Min. breaking load (lbs) 125 500 1,000

Max. safe working load (lbs) 25 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700 256,700

Cable with crimped hook end fixing:

Gripple Fastener:

Sizes: No.1-No.3

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

Size A (in.) B (in.) C (in.)

3/16” 1/4” 2 3/16”

1/4” 5/8” 3”

No. 2 1/4” 5/8” 3”

No. 3 1/4” 5/8” 3”

No. 1 (Mini)

No. 1

A

C B

Ceiling Attachment Snapped onto beam

clamp or clip

Light Fixture Snapped onto

clip or bracket

Page 7: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

EYELET FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Fixing sideways into wood beams, speakers or visual display, light fixtures, or other applications

that require bolting to brackets or fixtures. Hole is sized for a 1/4” fastener.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Straight Eyelet: Zinc plated steel

No.2 No.3

Cable Diameter (in.) 5/64 1/8

Strand configuration 7x7 7x7

Min. breaking load (lbs) 500 1,000

Max. safe working load (lbs) 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

No.1

1/16

7x7

125

25

256,700

Cable with crimped eyelet end fixing:

Gripple Fastener:

Sizes: No.1-No.3

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

Size

A (in.) Fastener

Size Ø

B (in.)

C (in.)

No. 2 1/4” 3/8” 1 3/4”

No. 3 1/4” 3/8” 1 3/4”

No. 1 1/4” 3/8” 1 3/4”

A

C

B

Suspended Speaker Bolted to brackets

Ceiling Attachment Drilled or screwed

to wood beam

Page 8: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

45O EYELET FUNCTION: The sway bracing of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Fastening into concrete, steel, or wood for sway bracing of services that are suspended with an

existing hanger. Hole is sized for a 3/8” fastener.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

45O Eyelet: Zinc plated steel

No.2

Cable Diameter (in.) 5/64

Strand configuration 7x7

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

No.3

1/8

7x7

1,000

200

256,700

Cable with crimped 45O eyelet end fixing:

Gripple Fastener:

Size: No.2-3

Max. Safe Working Load: No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

Size A (in.)

Fastener Size Ø

B (in.)

C (in.)

No. 2 3/8” 1 1/8” 7/8”

No. 3 3/8” 1 1/8” 7/8”

A B

C

Light Fixture or Service Sway bracing

Page 9: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

90O EYELET FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: For shot firing into concrete or steel. Can be used with mechanical anchors. Holes sized for 1/4”,

3/8”, or 1/2” fasteners.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

90O Eyelet: Zinc plated steel

No.1 No.2 No.3

Cable Diameter (in.) 1/16 5/64 1/8

Strand configuration 7x7 7x7 7x7

Min. breaking load (lbs) 125 500 1,000

Max. safe working load (lbs) 25 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700 256,700

Cable with crimped 90O eyelet end fixing:

Gripple Fastener:

Sizes: 1/4” - No.1-No.3

3/8” - No.3

1/2” - No.3

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

Size A (in.)

Fastener Size Ø

B (in.)

C (in.)

No. 2 1/4” 1” 1 1/2”

No. 3 1/4” 1” 1 1/2”

No. 1 1/4” 1” 1 1/2”

No. 3 3/8” 1 3/4” 1 5/16”

No. 3 1/2” 1 5/8” 1 1/2”

A

B

C

Chilled Beams Attached to service

Cable Basket On strut with Trapeze hangers

Light Fixture Attached to bracket

Page 10: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

END STOP FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Suspending from lighting channels, track, and other channel fixtures.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION: Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

End Stop: Zinc plated steel

No.1 No.2 No.3

Cable Diameter (in.) 1/16 5/64 1/8

Strand configuration 7x7 7x7 7x7

Min. breaking load (lbs) 125 500 1,000

Max. safe working load (lbs) 25 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700 256,700

No.4

3/16

7x19

2,475

495

256,700

Cable with crimped end stop end fixing:

Gripple Fastener:

Sizes: No.1-No.4

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

No.4 495 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Example

Size A

(in.) B

(in.) C

(in.)

No. 2 1/4” 5/16” 1/2”

No. 3 1/4” 3/8” 3/4”

No. 1 5/32” 1/4” 5/16”

No. 4 5/16” 1/2” 1 3/16”

A

B

C

Channel Slides into channel

to support service

Page 11: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

BARREL FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Attaches to any 1/4” or 3/8” male thread product.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Barrel End: Zinc plated steel

No.1 No.2 No.3

Cable Diameter (in.) 1/16 5/64 1/8

Strand configuration 7x7 7x7 7x7

Min. breaking load (lbs) 125 500 1,000

Max. safe working load (lbs) 25 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700 256,700

Cable with crimped barrel end fixing:

Gripple Fastener:

Sizes: 1/4” - No.1-No.2

3/8” - No.2-No.3

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

Size A

(in.) B

(in.) C

(in.)

No. 1 1/4” 7/16” 1 3/4”

No. 2 1/4” 7/16” 1 3/4”

No. 3 3/8” 1/2” 1 3/4”

No. 2 3/8” 1/2” 1 3/4”

C

A

B

On Suspended Ceilings By attaching to Gripple’s

T-Bar Twist Clip Signage In conjunction with a

1/4” or 3/8” male thread

Track Lighting In conjunction with a

1/4” or 3/8” male thread

Page 12: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Cable with crimped cladding hook end fixing:

CLADDING HOOK FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Metal decking roof structures. Fits into a 1/4” hole.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION: Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Cladding Hook: Zinc plated steel

No.2 No.3

Cable Diameter (in.) 5/64 1/8

Strand configuration 7x7 7x7

Min. breaking load (lbs) 500 1,000

Max. safe working load (lbs) 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

No.1

1/16

7x7

125

25

256,700

Gripple Fastener:

Size: No.1-No.3

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Example

Size A (in.) Hole

size Ø

B (in.)

C (in.)

No. 2 7/32” 15/16” 2 3/8”

No. 3 1/4” 1” 2 3/8”

Metal Decking Roof Structures Fits into a pre-drilled 7/32” or 1/4” hole

A

B

C

Page 13: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Y-TOGGLE FUNCTION: The suspension of light fixtures in an indoor stationary setting.

APPLICATION: Light fittings, light fixtures, and other cavities. Toggle sizes available to fit the following hole sizes:

5/16” and 1/4”.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Y-Assembly: 18” legs are standard. Other lengths available by request.

Toggle & End Stop: Zinc plated steel

Crimp/Ferrule: Aluminum

No.2

Cable Diameter (in.) 5/64

Strand configuration 7x7

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

No.1

1/16

7x7

125

25

256,700

Y-Fit crimped with end stops and toggle plates:

Gripple Fastener:

Sizes: 5/16” - No.1-No.2

1/4” - No.2

Max. Safe Working Load: No.1 25 lbs

No.2 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

B A

C

E

D

Size A

(in.) B

(in.) C

(in.) D

(in.) E

(in.)

No. 2 5/16” 1/4” 15/32” 5/16” 1 9/16”

1/4” 1/4” 15/32” 1/4” 1 9/16”

Angle between legs of ‘Y’ not to exceed 60O

Ceiling Grid Troffer Support Inserts into pre-drilled holes

Light Fixture Inserts into pre-drilled holes

Page 14: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Y-HOOK FUNCTION: The suspension of light fixtures, cable containment (basket / tray), and HVAC services in an indoor

stationary setting.

APPLICATION: Attachment to services with 1/4” minimum holes in hanging brackets. Ideal for services that require

maintenance. Attachment to top rail of cable or basket tray should be per cable / basket tray

manufacturer’s approval.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Y-Assembly: 18” legs are standard. Other lengths available by request.

Hook: Zinc plated steel

Crimp/Ferrule: Aluminum

No.2 No.3

Cable Diameter (in.) 5/64 1/8

Strand configuration 7x7 7x7

Min. breaking load (lbs) 500 1,000

Max. safe working load (lbs) 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

No.1

1/16

7x7

125

25

256,700

Y-Fit with crimped hook end fixing:

Gripple Fastener:

Sizes: No.1-No.3

Max. Safe Working Loads: No.1 25 lbs

No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

A

C

B

Size Specs Application Examples

Radiant Panel Attached directly

to service

Light Fixture Snapped onto

clip or bracket

Cable Basket Attachment to

top rails*

* per cable basket

manufacturer’s approval

Angle between legs of ‘Y’ not to exceed 60O

Size A (in.) B (in.) C (in.)

3/16” 1/4” 2 3/16”

1/4” 5/8” 3”

No. 2 1/4” 5/8” 3”

No. 3 1/4” 5/8” 3”

No. 1 (Mini)

No. 1

Page 15: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

STAINLESS STEEL LOOP FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor environment where

stainless steel products are specified.

APPLICATION: Choking around bar joists, purlins, beams, roof trusses, strut, and other accessible building

features. Must be used with stainless steel accessories. Not recommended for use in chlorinated

environments.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type 316/A4 Stainless Steel

Wedge Ceramic

Spring Type 302 Stainless Steel

End Cap Type 316/A4 Stainless Steel

Cable: Type 316L/A4 Stainless Steel.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Crimp/Ferrule: 316/A4 Stainless Steel

No.2 No.3

Cable Diameter (in.) 5/64 1/8

Strand configuration 7x7 7x7

Min. breaking load (lbs) 500 1,000

Max. safe working load (lbs) 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

Gripple Fastener:

Sizes: No.2-No.3

Max. Safe Working Loads: No.2 100 lbs

No.3 200 lbs

Cable with crimped loop end fixing:

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

A (in.)

(approx.)

B (in.)

(approx.)

C (in.)

D (in.)

No.2 1 3/16” 2 3/8” 1/2” 5/16”

No.3 1 3/16” 2 3/8” 5/8” 3/8”

Spiral Duct, Small Choke

Spiral Duct, Large Cradle

Light Fixture with V-Bracket

Ceiling Attachment

with Ceiling Clip

A

C

B

D

Page 16: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

STAINLESS STEEL STUD FUNCTION:

The suspension of HVAC, Mechanical, Lighting & Electrical services in an in an indoor

environment where stainless steel products are specified.

APPLICATION: Concrete structures, metal decking, metal brackets using nuts, and clamps & clevis hangers.

Works with a 1/4” anchor. Must be used with stainless steel accessories. Not recommended for

use in chlorinated environments.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type 316/A4 Stainless Steel

Wedge Ceramic

Spring Type 302 Stainless Steel

End Cap Type 316/A4 Stainless Steel

Cable: Type 316/A4 Stainless Steel.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Stud End: Type 304/A2 Stainless Steel

No.2 No.3

Cable Diameter (in.) 5/64 1/8

Strand configuration 7x7 7x7

Min. breaking load (lbs) 500 1,000

Max. safe working load (lbs) 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

Cable with crimped 1/4” stud end fixing:

Gripple Fastener:

Sizes: 1/4” - No.2-No.3

Max. Safe Working Loads: No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

A (in.) Anchor Size Ø

B (in.)

C (in.)

1/4” 1” 2”

Size Specs

A

C

B

Application Examples

Spiral Duct Stud up

Cable Basket Stud up

Track Lighting Stud down

Page 17: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

STAINLESS STEEL TOGGLE FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an in an indoor

environment where stainless steel products are specified.

APPLICATION: Fixes into specific hole diameters of light fixtures, profile roof cladding, and other pre-drilled

structures or services. Must be used with stainless steel accessories. Toggle sized to fit a 5/16”

hole. Not recommended for use in chlorinated environments.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type 316/A4 Stainless Steel

Wedge Ceramic

Spring Type 302 Stainless Steel

End Cap Type 316/A4 Stainless Steel

Cable: Type 316/A4 Stainless Steel.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Toggle Plate & End Stop: 304/A2 Stainless Steel

No.2

Cable Diameter (in.) 5/64

Strand configuration 7x7

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

Cable with end stop and 5/16” toggle plate:

Gripple Fastener:

Size: No.2

Max. Safe Working Load: No.2 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

B

A

C

E

D

Size A (in.)

Hole size Ø B (in.) C (in.) D (in.) E (in.)

No. 2 5/16” 1/4” 15/32” 5/16” 1 9/16”

Size Specs Application Examples

Spiral Duct Toggle up, via hole

drilled in metal deck

Light Fixture Toggle down

Page 18: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

STAINLESS STEEL HOOK FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an in an indoor

environment where stainless steel products are specified.

APPLICATION: Stainless steel beam & purlin clips, basket tray / cable tray, light fixtures, or any service or clip with

a 1/4” hole. Must be used with stainless steel accessories. Attachment to top rail of cable basket

or tray should be per manufacturer’s approval. Not recommended for use in chlorinated

environments.

LOAD RATING: Stainless Steel Hook Hangers have a 4:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type 316/A4 Stainless Steel

Wedge Ceramic

Spring Type 302 Stainless Steel

End Cap Type 316/A4 Stainless Steel

Cable: Type 316L/A4 Stainless Steel.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Hook: 304/A2 Stainless Steel

No.2

Cable Diameter (in.) 5/64

Strand configuration 7x7

Min. breaking load (lbs) 400

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

Cable with crimped hook end fixing:

Gripple Fastener:

Size: No.2

Max. Safe Working Load: No.2 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

Size A (in.) B (in.) C (in.)

No. 2 1/4” 5/8” 3”

A

C B

Ceiling Attachment Snapped onto beam

clamp or clip

Light Fixture Snapped onto

clip or bracket

Page 19: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

STAINLESS STEEL Y-TOGGLE

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data FUNCTION: The suspension of light fixtures in an indoor stationary setting where stainless steel products are

specified.

APPLICATION: Light fittings, light fixtures, and other cavities. Toggle sizes available to fit a 5/16” hole. Must be

used with stainless steel accessories. Not recommended for use in chlorinated environments.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type 316/A4 Stainless Steel

Wedge Ceramic

Spring Type 302 Stainless Steel

End Cap Type 316/A4 Stainless Steel

Cable: Type 316/A4 Stainless Steel.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Y-Assembly: 18” legs are standard. Other lengths available by request.

Toggle Plate & End Stop: 304/A2 Stainless Steel

Crimp/Ferrule: 316/A4 Stainless Steel

No.2

Cable Diameter (in.) 5/64

Strand configuration 7x7

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

Y-Fit crimped with end stops and toggle plates:

Gripple Fastener:

Size: No.2 (5/16”)

Max. Safe Working Load: No.2 100 lbs

Size Specs

B A

C

E

D

Size A

(in.) B

(in.) C

(in.) D

(in.) E

(in.)

No. 2 5/16” 1/4” 15/32” 5/16” 1 9/16”

Application Examples

Angle between legs of ‘Y’ not to exceed 60O

Ceiling Grid Troffer Support Inserts into pre-drilled holes

Light Fixture Inserts into pre-drilled holees

Page 20: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

STAINLESS STEEL Y-HOOK

FUNCTION: The suspension of light fixtures, cable containment (basket / tray), and HVAC services in an indoor

stationary setting where stainless steel products are specified.

APPLICATION: Ideal for services that require maintenance. Attachment to top rail of cable or basket tray should be

per cable / basket tray manufacturer’s approval. Must be used with stainless steel accessories. Not

recommended for use in chlorinated environments.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type 316/A4 Stainless Steel

Wedge Ceramic

Spring Type 302 Stainless Steel

End Cap Type 316/A4 Stainless Steel

Cable: Type 316/A4 Stainless Steel.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Y-Assembly: 18” legs are standard. Other lengths available by request.

Hook: 304/A2 Stainless Steel

Crimp/Ferrule: 316/A4 Stainless Steel

No.2

Cable Diameter (in.) 5/64

Strand configuration 7x7

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

Y-Fit with crimped hook end fixing:

Gripple Fastener:

Size: No.2

Max. Safe Working Load: No.2 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size

A (in.)

B (in.)

C (in.)

No.2 1/4” 5/8” 3”

Application Examples

Radiant Panel Attached directly

to service

Light Fixture Snapped onto

clip or bracket

Cable Basket Attachment to

top rails*

* per cable basket

manufacturer’s approval

Size Specs

Angle between legs of ‘Y’ not to exceed 60O

A

C

B

Page 21: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

A

B

No.3 TRAPEZE FASTENER FUNCTION:

The suspension of HVAC, Mechanical & Electrical services in conjunction with strut in an indoor

stationary setting.

APPLICATION: Ideal for single or multi-tiered installations and low void ceilings. Available in a kit with cable and

choice of pre-attached end fixing.

LOAD RATING: The No.3 Trapeze hanger has a 5:1 safety factor.

MATERIAL SPECIFICATION:

No.3 Trapeze Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

No.3

Cable Diameter (in.) 1/8

Strand configuration 1x19

Min. breaking load (lbs) 1,000

Max. safe working load (lbs) 200

Tensile strength (lbs/sq. in.) 256,700

Single channel Gripple fastener for use with No.3 Gripple hangers:

Size: No.3

Max. Safe Working Load: No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs

Size A (in.) B (in.)

No. 3 1 7/8” 1 9/16”

Oval Duct Rectangular Duct With Gripple Trapeze Brackets

Pipework

Cable Basket Ladder Tray

Application Examples

Page 22: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

FUNCTION: The suspension of HVAC, Mechanical & Electrical services in conjunction with strut in an indoor

stationary setting.

APPLICATION: Ideal for single or multi-tiered installations and low void ceilings. Available in a kit with cable and

choice of pre-attached end fixing. Pre-fits onto strut channel to limit time spent working at heights.

LOAD RATING: The No.2 Trapeze hanger has a 5:1 safety factor.

MATERIAL SPECIFICATION:

No.2 Trapeze Fastener: Housing Type ZA2 Zinc

Super-Wedge Hardened carbon steel

Spring Stainless Steel (Type A2 / 302)

End Cap EPDM 40 Shore A

Release Pin Stainless Steel (Type A2 / 304)

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

No.2

Cable Diameter (in.) 5/64

Strand configuration 1x19

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

Single channel Gripple fastener for use with No.2 Gripple hangers:

Size: No.2

Max. Safe Working Load: No.2 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs

Size A

(in.) B

(in.)

No. 2 1 1/2” 7/8”

C (in.)

13/16”

D (in.)

1 3/32”

Application Examples

No.2 TRAPEZE FASTENER

Rectangular Duct on strut

Cable Basket on strut

With Cable Basket Adaptors

Page 23: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

DUCT TRAPEZE FUNCTION: The suspension of rectangular ductwork, fan coil units, and other suitable services in an indoor

stationary setting.

APPLICATION: Attaches to service at three points with self-tapping screws. Comes in a kit with cable and choice

of pre-attached end fixing.

LOAD RATING: All Duct Trapeze products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Trapeze Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

No.2

Cable Diameter (in.) 5/64

Strand configuration 1x19

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

Single channel Gripple fastener with integral bracket for use with No.2 Gripple hangers:

Size: No.2

Max. Safe Working Load: No.2 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs

Dimension Inches

A 2 3/4”

B 2 3/8”

C 1 1/2”

D Ø 13/64”

Application Examples

A

B

C

D

E F G

Dimension Inches

E 1 1/2”

F 1 7/32”

G 1”

Rectangular Ductwork Rectangular Ductwork

(double tier)

Page 24: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

C-CLIP HANGER FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: Twists onto Cable Strut for suspending a service or a Y-Fit Accessory Hanger. 1/8” C-Clip Hanger to

be used with 1/8” Cable Strut/ 1/4” C-Clip Hanger to be used with 1/4” Cable Strut.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

C-Clip: Housing Type ZA2 Zinc

Cams Hardened carbon steel

Springs Steel

Pins Mild Steel

1/8” and 1/4”

Cable Diameter (in.) 5/64

Strand configuration 7x7

Min. breaking load (lbs) 500

Max. safe working load (lbs) 100

Tensile strength (lbs/sq. in.) 256,700

C-Clip with attached standard Loop Hanger:

Gripple Fastener:

Sizes: 1/8”

1/4”

Max. Safe Working Loads: 1/8” 35 lbs

1/4” 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Application Examples

Spiral Duct Double span

Light Fixture

Single span

Light Fixture

Double span

Submittal Data

Cable Basket

Page 25: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

CABLE STRUT

FUNCTION: The suspension of HVAC, Mechanical, Lighting & Electrical services in an indoor stationary setting.

APPLICATION: 1/4” Cable Strut is ideal for heavier services and longer cable spans; to be used with 1/4” C-Clip

Hanger. 1/8” Cable Strut is ideal for light fixtures and lighter services; to be used with 1/8” C-Clip

Hanger.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Lockable Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 10ft-100ft, other lengths can be made to order.

1/8” 1/4”

Cable Diameter (in.) 1/8 1/4

Strand configuration 7x7 7x19

Min. breaking load (lbs) 350 1,100

Max. safe working load (lbs) 200 715

Tensile strength (lbs/sq. in.) 256,700 256,700

Cable with two Gripple (1/8”) or Lockable (1/4”) Fasteners:

Gripple Fastener: (w/ 1/8” Cable Strut)

Sizes: 1/8”

1/4”

Max. Safe Working Loads: 1/8” 70 lbs

1/4” 220 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Application Examples

Lockable Fastener: (w/ 1/4” Cable Strut)

Spiral Duct Double span

Light Fixture

Single span

Light Fixture

Double span

Submittal Data

Cable Basket

Page 26: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Gripple Spider Kit FUNCTION: Cast-in-place pre-insert concrete anchoring solution for the suspension of Mechanical and Electrical

services in an indoor stationary setting.

APPLICATION: Insert is installed directly onto the wood forms/shuttering prior to the concrete pour. Swivel Toggle

attaches into insert from below.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Spider Anchor: Legs—pressed steel, passivated. Insert—injection molded plastic rubber.

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-30ft, other lengths can be made to order.

Swivel Toggle End: Zinc plated steel

No.2 No.3

Cable Diameter (in.) 5/64 1/8

Strand configuration 7x7 7x7

Min. breaking load (lbs) 500 1,000

Max. safe working load (lbs) 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

Gripple Fastener, Standard: (No.2-3 Trapeze, and

No.2 Duct Trapeze

fastener options also

available)

Sizes: No.2-No.3

Max. Safe Working Loads: No.2 100 lbs

No.3 200 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Example

Cast-in-place concrete insert:

Cable with crimped Swivel Toggle end fixing:

1 1/2”

1 1/8” 1 5/8”

4 1/2”

Page 27: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

FUNCTION - A pre-insert solution for metal decks to suspend mechanical and electrical services.

APPLICATION - Specifically designed for pre-inserting into metal decks prior to the concrete being poured.

LOAD RATING - All products have a 5:1 safety factor.

MATERIAL SPECIFICATION -Metal Deck Insert - Rubber Head: EPDM 85+-5 Shore A Black; Finish - As Moulded Plastic Tube: Polypropylene; Finish - As Moulded Metal Washer: CR4 Steel; Finish: BS EN12329:2000 FE//ZN5//A

Gripple Fastener: Housing Type ZA2 Zinc Wedge Sintered steel hardened to min. 56 Rockwell C Spring Stainless Steel (Type 302) End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385. Standard lengths from 5ft-30ft, other lengths can be made to order.

Swivel Toggle End: Zinc plated steel

Metal Deck Insert:

Cable with crimped Swivel Toggle end fixing:

Gripple Fastener, Standard: (No.2-3 Trapeze, and No.2 Duct Trapeze fastener options also available)

Sizes: No.2 and No.3

Max. Safe Working Loads: No.2 - 100 lbs No.3 - 200 lbs

PRODUCT INFORMATIONMETAL DECK INSERT KIT

APPLICATION EXAMPLE SIZE SPECIFICATION

Submittal Data

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

www.gripple.comPI-70-USA-SUBMIT

No.2 No.3

Cable Diameter (in.) 5⁄64 1⁄8

Strand configuration 7 x 7 7 x 7

Min. breaking load (lbs) 500 1,000

Max. safe working load (lbs) 100 200

Tensile strength (lbs/sq. in.) 256,700 256,700

F

B

EA

C D

Dimension Size (in)

A 2 3⁄8

B 1

C Ø 7⁄32

D Ø 11⁄32

E 2 3⁄16

F 1 1⁄2”

LOAD

Page 28: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Shot Fire Hanger (SF35) FUNCTION: Shot-fired hanger solution with premounted nail end fixing for suspending Mechanical or Electrical

services in an indoor stationary setting.

APPLICATION: For shot firing into concrete or concrete over metal deck. For installing with DX351 and P3500

tools.

LOAD RATING: All products have a 5:1 safety factor.

MATERIAL SPECIFICATION:

Gripple Fastener: Housing Type ZA2 Zinc

Wedge Sintered steel hardened to min. 56 Rockwell C

Spring Stainless Steel (Type 302)

End Cap UV stabilized homopolymer polypropylene

Cable: Galvanized high tensile steel cable to EN12385.

Standard lengths from 5ft-15ft, other lengths can be made to order.

Nail: Galvanized steel

No.1 No.2

Cable Diameter (in.) 1/16 5/64

Strand configuration 7x7 7x7

Min. breaking load (lbs) 125 500

Max. safe working load (lbs) 33 100

Tensile strength (lbs/sq. in.) 256,700 256,700

Standard Gripple Fastener (No.2): (No.1 Express fastener,

No.2 Trapeze fastener,

and No.2 Duct Trapeze

fastener options also

available)

Sizes: No.1-No.2

Max. Safe Working Loads: No.1 33 lbs

No.2 100 lbs

GRIPPLE INC. 1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753 Email: [email protected] www.gripple.com/us

Submittal Data

Size Specs Application Examples

Shank diameter (in.) 9/64”

Shank length (in.) 1 1/4”

Head diameter (in.) 5/16”

Plastic washer diameter (in.)

5/16” Spiral Duct Rectangular Duct

Page 29: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

1611 Emily Lane Aurora, IL 60502 Ph: 866-474-7753

Email: [email protected]

www.gripple.com/us

Vers. 4_13

Page 30: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high
Page 31: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high
Page 32: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Threaded Deck Insert Submittal Information

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

BUS-SUB-HVAC-US-TDI

www.gripple.com

Gripple’s policy is one of continuous development and innovation. We therefore reserve the right to alter specifications, etc. without notice.

THREADED DECK INSERT

Function - A pre-insert solution for metal decks to suspend mechanical and electrical devices.

Application - Insert is installed directly onto metal deck prior to the concrete pour. Threaded rod attaches into the insert from below.

Load rated - All products have a 3:1 safety factor

Material Specification - Metal Deck Insert

Head - RubberWasher - Steel, zinc plated passivatedTube - Polypropylene

Note: Threaded rod must be specified seperately to the Insert.

SIZE SPECIFICATION

PRODUCT INFORMATION

Stud Size SWL

3⁄8 - 16 UNC 700 lb

Dimension Size (in)

A 2 3⁄4

B 1

C - 3/16” 11/16

D ø 7⁄32

APPLICATION

>Maxkg/lbs

>60°

>60° >60°

C

A

B

D

Page 33: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Threaded Deck Insert Submittal Information

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

BUS-SUB-HVAC-US-TDI

www.gripple.com

Gripple’s policy is one of continuous development and innovation. We therefore reserve the right to alter specifications, etc. without notice.

THREADED DECK INSERT

Function - A pre-insert solution for metal decks to suspend mechanical and electrical devices.

Application - Insert is installed directly onto metal deck prior to the concrete pour. Threaded rod attaches into the insert from below.

Load rated - All products have a 3:1 safety factor

Material Specification - Metal Deck Insert

Head - RubberWasher - Steel, zinc plated passivatedTube - Polypropylene

Note: Threaded rod must be specified seperately to the Insert.

SIZE SPECIFICATION

PRODUCT INFORMATION

Stud Size SWL

3⁄8 - 16 UNC 700 lb

Dimension Size (in)

A 2 3⁄4

B 1

C - 3/16” 11/16

D ø 7⁄32

APPLICATION

>Maxkg/lbs

>60°

>60° >60°

C

A

B

D

Page 34: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Pipe brackets Submittal Information

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

BUS-PI-MEP-US-PIPE BRACKET

www.gripple.com

>Maxkg/lbs

>60°

>60° >60°

Gripple’s policy is one of continuous development and innovation. We therefore reserve the right to alter specifications, etc. without notice.

MOUNTING CONCEPTS

PRODUCT SPECIFICATIONS

Pipe brackets come in pre-assembled kits with Universal Clamps for quick and easy support of pipework and are delivered to site for immediate installation.

FUNCTION / APPLICATION

FUNCTION - The installation and securing of pipework in an indoor stationary setting.

APPLICATION - Used for hanging and securing pipework

from 1/2” copper to 3” steel. Can be bolted directly to deck or wall or suspended from the deck using Hangers or a Y-Fit Hanger.

LOAD RATING - 200 lb SWL with 5:1 safety factor.

MATERIAL - Mild Steel.

PB640 with Universal Clamps

PB380 with Universal Clamps

PB230 with Universal Clamps

Bolted directly to soffit Suspended from the soffit using Trapeze No.2

Bolted to the wall

Max. Working Load on 3/8” Threaded rod 50 lb.

Product Information

Bracket Length (in) Configuration Pipe Centers

(in)

PB230 9” With 2 clamps 6”

PB380 15”With 2 clamps 6” / 8”

With 3 clamps 6”

PB640 25”With 4 clamps 6” / 8”

With 5 clamps 6”

6” - 8”

PB230, PB380 or PB640

1/4” Threaded rod (2”)

Universal clamp

Maximum Working Load on brackets in all orientations

200 lb

1 11⁄16 ”

1 3⁄8”9”

15”

Jointing Bracket

25”7” 1 1⁄2“

1 1⁄4”

Page 35: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Pipe brackets Submittal Information

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

BUS-PI-MEP-US-PIPE BRACKET

www.gripple.com

>Maxkg/lbs

>60°

>60° >60°

Gripple’s policy is one of continuous development and innovation. We therefore reserve the right to alter specifications, etc. without notice.

PB380 Version - Available in pre-assembled kits of 2 or 3 Universal Clamps.

PB640 Version - Available in pre-assembled kits of 4 or 5 Universal Clamps.

6” 6”6” 6”

8” 8”8” 8”

6” 6”6” 6” 6”

PB230 Version - Available in pre-assembled kits of 2 Universal Clamps.

Pre-assembled with 2 clamps with 6” spacing

Product code: PB380-2-6IN-GCI

Pre-assembled with 2 clamps with 8” spacing

Product code: PB380-2-8IN-GCI

Pre-assembled with 4 clamps with 8” spacing

Product code: PB640-4-8IN-GCI

Pre-assembled with 3 clamps with 6” spacing

Product code: PB380-3-6IN-GCI

Pre-assembled with 5 clamps with 6” spacing

Product code: PB640-5-6IN-GCI

Pre-assembled with 4 clamps with 6” spacing

Product code: PB640-4-6IN-GCI

Pre-assembled with 2 clamps with 6” spacing

Product code: PB230-2-6IN-GCI

6”

Jointing Bracket available separately

Product code: PB-CONN

6”

Jointing Bracket - Used to join Pipe Brackets to produce longer lengths.

Page 36: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Approvals Overview General Information

MSS SP-58-2009: Pipe Hangers and Supports – Materials, Design, Manufacture, Selection, Application, and Installation

WHAT IS MSS? Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry is a non-profit technical association organized for development and improvement of industry, national and international codes and standards.

Mandatory conformance to this Standard Practice is established only by reference in other documents such as a code, specification, sales contract, or public law, as applicable.

APPLICABLE SECTIONS:

1. SCOPE1.1 This Standard Practice establishes the material, design, fabrication, and inspection criteria to be used in the manufacture of standard types of pipe hanger components.

1.3 This Standard Practice establishes minimum design load ratings for rigid pipe hanger assemblies

(see Table 1). (Minimum Design Load from Table 1 for a 2” / DN 50 Nominal Pipe is 150 lbs / 0.67 kN)

3. MATERIALS3.1 Materials commonly used in manufacturing pipe hangers and supports are listed in Tables A2 and A2M. (ASTM A 653 SS is an allowable material)

3.5 Materials subject to corrosion or galvanic action shall be protected as specified by the engineering design and such protection shall be applied in accordance with the coating requirements of Section 10.

5. PIPING SYSTEMS5.1 Temperature5.1.1 This section establishes an identification of piping systems according to the operating (service) temperatures of the piping contents for the purpose of pipe hanger and support selection.

5.1.2 Typical product types for use at these temperature ranges can be found in Table A1. (Side Load Hanger is comparable to Types 1, 5 ,7, 9 & 10)

5.2 Hanger and Support Spacing5.2.1 The recommended maximum spacing of hangers shall be as shown in Table 4.

5.2.2 Spacing’s less than shown in Table 4 may be required to conform with building structure loading limitations and standard product load ratings. (Refer to Table 4 for maximum spacing of hangers)

5.2.3 The recommended minimum rod diameters for rigid rod hangers are listed in Table 3. (Min rod diameter for a 2” / DN 50 Nominal pipe is 3/8” / M10

5.4 Fire Protection Systemsa) Hangers and supports for fire protection systems shall conform to the following standards published by the National Fire Protection Association in the National Fire Codes for fixed extinguishing equipment: (Side Load Hanger is compatible with NFPA 13 Installation of Sprinkler Systems)

5.5 Insulated Lines5.5.1 For piping systems using Type 40 protection shield for insulated piping, see Table A3 for spacing. Insulation protection shields shall be provided to protect the vapor barrier of insulation on cold lines. Under no circumstances shall hangers, supports or guides be applied directly to horizontal pipe or tubing on vapor barriered lines. (See Table A3.) (Side Load Hanger is compatible with Type 40 protection shields – tbc)

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

PI-66-US-APPROVALS-MSS-SP-58

www.gripple.com

Continued overleaf...

Page 37: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

6. GENERAL REQUIREMENTS

6.1 Where applicable, selection and application of pipe hangers and supports may be required to conform to codes and standards, such as:

c) UL 203 Standard for Pipe Hanger Equipment for Fire Protection Service (Listing applied for)

d) Factory Mutual FM 1951/1952/1953 Approval Standard for Pipe Hanger Components for Automatic Sprinkler Systems (Listing to be applied for)

e) NFPA 13 Installation of Sprinkler Systems (Side Load Hanger is compatible)

7. PRODUCT DESIGN

7.1 GENERAL HANGERS

7.1.1

Unprotected flat steel shall have a minimum thickness of 0.120 inch (3.2mm) and a minimum width of 1 inch (25.4mm). The minimum cross section for unprotected hangers (Types 1,5,7,9 and 10) shall be 0.105 inch (2.7mm) x 0.88 inch (22.4mm). As an exception, for pipe NPS 1 (DN25) and smaller the minimum cross section shall be 0.060 inch (1.6mm) x 0.75 inch (19.1mm). Equivalent cross section may be substituted provided the minimum thickness is not decreased.

7.1.2 Hangers that meet the tabulated load requirements of Table 1 and that have protective coatings in accordance with SECTION 10 need not conform to the minimum dimensional requirements of Section 7.1.1. (see Section 10)

7.1.3 Hangers and supports shall be sized to fit the outside diameter of the pipe, tubing, or, if specified, the outside diameter of insulation. Manufacturer’s catalog hangers provide a nominal clearance over standard tolerance piping and tubing. Consideration for fit should be given by the user for large diameter and/or out of tolerance piping and tubing.

9. TOLERANCES

9.1 RAW MATERIAL AND PURCHASED COMPONENTS

9.1.1 Tolerances for raw materials such as strip, sheet, bar, plate, pipe, tubing, structural and bar size shapes, bolting, hot wound springs and cold wound springs shall be in accordance with recognized standards or specifications.

10. PROTECTIVE COATINGS

10.3.3 Pre-galvanized steel shall meet the requirements of ASTM A 653. (G90 indicates a coating thickness of 0.9 oz/ft2 as specified in ASTM A 653 and is equivalent to 0.45 oz/ft2 per side)

Extracted from ANSI/MSS SP-58-2009 with permission of the publisher, Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.

Approvals Overview General Information

MSS SP-58-2009: continued

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

PI-66-US-APPROVALS-MSS-SP-58

www.gripple.com

Page 38: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Approvals Overview General Information

MSS SP-58-2009: Pipe Hangers and Supports – Materials, Design, Manufacture, Selection, Application, and Installation

WHAT IS MSS? Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry is a non-profit technical association organized for development and improvement of industry, national and international codes and standards.

Mandatory conformance to this Standard Practice is established only by reference in other documents such as a code, specification, sales contract, or public law, as applicable.

APPLICABLE SECTIONS:

1. SCOPE1.1 This Standard Practice establishes the material, design, fabrication, and inspection criteria to be used in the manufacture of standard types of pipe hanger components.

1.3 This Standard Practice establishes minimum design load ratings for rigid pipe hanger assemblies

(see Table 1). (Minimum Design Load from Table 1 for a 2” / DN 50 Nominal Pipe is 150 lbs / 0.67 kN)

3. MATERIALS3.1 Materials commonly used in manufacturing pipe hangers and supports are listed in Tables A2 and A2M. (ASTM A 653 SS is an allowable material)

3.5 Materials subject to corrosion or galvanic action shall be protected as specified by the engineering design and such protection shall be applied in accordance with the coating requirements of Section 10.

5. PIPING SYSTEMS5.1 Temperature5.1.1 This section establishes an identification of piping systems according to the operating (service) temperatures of the piping contents for the purpose of pipe hanger and support selection.

5.1.2 Typical product types for use at these temperature ranges can be found in Table A1. (Side Load Hanger is comparable to Types 1, 5 ,7, 9 & 10)

5.2 Hanger and Support Spacing5.2.1 The recommended maximum spacing of hangers shall be as shown in Table 4.

5.2.2 Spacing’s less than shown in Table 4 may be required to conform with building structure loading limitations and standard product load ratings. (Refer to Table 4 for maximum spacing of hangers)

5.2.3 The recommended minimum rod diameters for rigid rod hangers are listed in Table 3. (Min rod diameter for a 2” / DN 50 Nominal pipe is 3/8” / M10

5.4 Fire Protection Systemsa) Hangers and supports for fire protection systems shall conform to the following standards published by the National Fire Protection Association in the National Fire Codes for fixed extinguishing equipment: (Side Load Hanger is compatible with NFPA 13 Installation of Sprinkler Systems)

5.5 Insulated Lines5.5.1 For piping systems using Type 40 protection shield for insulated piping, see Table A3 for spacing. Insulation protection shields shall be provided to protect the vapor barrier of insulation on cold lines. Under no circumstances shall hangers, supports or guides be applied directly to horizontal pipe or tubing on vapor barriered lines. (See Table A3.) (Side Load Hanger is compatible with Type 40 protection shields – tbc)

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

PI-66-US-APPROVALS-MSS-SP-58

www.gripple.com

Continued overleaf...

Page 39: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

6. GENERAL REQUIREMENTS

6.1 Where applicable, selection and application of pipe hangers and supports may be required to conform to codes and standards, such as:

c) UL 203 Standard for Pipe Hanger Equipment for Fire Protection Service (Listing applied for)

d) Factory Mutual FM 1951/1952/1953 Approval Standard for Pipe Hanger Components for Automatic Sprinkler Systems (Listing to be applied for)

e) NFPA 13 Installation of Sprinkler Systems (Side Load Hanger is compatible)

7. PRODUCT DESIGN

7.1 GENERAL HANGERS

7.1.1

Unprotected flat steel shall have a minimum thickness of 0.120 inch (3.2mm) and a minimum width of 1 inch (25.4mm). The minimum cross section for unprotected hangers (Types 1,5,7,9 and 10) shall be 0.105 inch (2.7mm) x 0.88 inch (22.4mm). As an exception, for pipe NPS 1 (DN25) and smaller the minimum cross section shall be 0.060 inch (1.6mm) x 0.75 inch (19.1mm). Equivalent cross section may be substituted provided the minimum thickness is not decreased.

7.1.2 Hangers that meet the tabulated load requirements of Table 1 and that have protective coatings in accordance with SECTION 10 need not conform to the minimum dimensional requirements of Section 7.1.1. (see Section 10)

7.1.3 Hangers and supports shall be sized to fit the outside diameter of the pipe, tubing, or, if specified, the outside diameter of insulation. Manufacturer’s catalog hangers provide a nominal clearance over standard tolerance piping and tubing. Consideration for fit should be given by the user for large diameter and/or out of tolerance piping and tubing.

9. TOLERANCES

9.1 RAW MATERIAL AND PURCHASED COMPONENTS

9.1.1 Tolerances for raw materials such as strip, sheet, bar, plate, pipe, tubing, structural and bar size shapes, bolting, hot wound springs and cold wound springs shall be in accordance with recognized standards or specifications.

10. PROTECTIVE COATINGS

10.3.3 Pre-galvanized steel shall meet the requirements of ASTM A 653. (G90 indicates a coating thickness of 0.9 oz/ft2 as specified in ASTM A 653 and is equivalent to 0.45 oz/ft2 per side)

Extracted from ANSI/MSS SP-58-2009 with permission of the publisher, Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.

Approvals Overview General Information

MSS SP-58-2009: continued

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

PI-66-US-APPROVALS-MSS-SP-58

www.gripple.com

Page 40: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

PRODUCT INFORMATION

SIZE SPECIFICATION APPLICATION

Spider (Threaded concrete insert) Submittal Information

Cast-in-place concrete insert:

Sizes: 3/8” thread

Max. Safe Working Load: 700 lbs

SPIDER TCI

FUNCTION - Cast-in-place pre-insert concrete anchoring solution for the suspension of Mechanical and Electrical services in an indoor setting. Accommodates 3/8” threaded rod or

3/8” Stud Hanger.

APPLICATION - Insert is installed directly onto the wood forms/Shuttering prior to the concrete pour. Threaded rod/stud attaches into the insert from below.

LOAD RATING - All products have a 3:1 safety factor

MATERIAL SPECIFICATION -

Spider Anchor:

Legs – pressed steel, passivated

Nutsert – Steel, zinc plated, passivated

Dome – Injection moulded plastic rubber

Belly – Injection moulded plastic rubber

NOTE: Threaded Rod or Stud Hanger must be specified separately to the Insert.

Dimension Size (in)

A 1 1⁄18

B 1 5⁄8

C 4 1⁄2

BA

C

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

BUS-SUB-GEN-US-SPIDER TCI

www.gripple.com

Gripple’s policy is one of continuous development and innovation. We therefore reserve the right to alter specifications, etc. without notice. >Max

kg/lbs

>60°

>60° >60°

For use with 3/8” threaded rod or Stud Hangers.

Page 41: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Trapeze Plus Range Submittal Information

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

BUS-SUB-MEP-US-TPZ+

www.gripple.com

>Maxkg/lbs

>60°

>60° >60°

Gripple’s policy is one of continuous development and innovation. We therefore reserve the right to alter specifications, etc. without notice.

TRAPEZE PLUS FASTENER

APPLICATIONSIZE SPECIFICATION

PRODUCT INFORMATIONFunction - The suspension of pipework and armoured cable in conjuction with a pipe clevis or other MEP services in conjunction with strut in an indoor stationary setting.Application - Ideal for suspending pipework and other services having a circular cross section when used with standard, commercially available pipe clevis. Can also be used with a flanged nut, square plate washer, or strut nut for supporting other MEP services with a length of strut.Load Rating - The Trapeze hanger range has a 3:1 safety factor.Material Specification -Trapeze Fastener1) Carriage Mild Steel (Type EN1A) Bright Zinc Plated2) Balls Grade 40 Chrome Steel3) Spring Stainless Steel (Type 302)4) Locking Nut (knurled) Mild Steel (Type EN1A) - Bright Zinc Plated5) Threaded Adaptor Mild Steel (Type EN1A) - Bright Zinc Plated6) Housing Mild Steel (Type EN1A) - Bright Zinc Plated7) Nut Mild Steel (Type EN1A) - Bright Zinc PlatedCable Galvanised high tensile steel cable to EN12385Standard lengths from 5 ft - 30 ft, other lengths can be made to order.

No. 2 No.3 No.4Cable Diameter (in.) 3⁄64 1⁄8 3⁄16

Cable Configuration 7 x 7 7 x 7 7 x 19Min Breaking Load (lbs) 300 600 1485

Tensile Strength (lbs/sq.in.) 256,700

Gripple fastener for suspension of universal strut or clevis hangers using steel cable.

Size: No.2Max. Safe Working Load: No.2 - 100 lbs Size: No.3Max. Safe Working Load: No.3 - 200 lbsSize: No.4Max. Safe Working Load: No.4 - 495 lbs

A

D

G

F

B

C

E

Dimension No.2(in)

No.3(in)

No.4(in)

A 1 1⁄2 1 3⁄4 2 5⁄32

B 1 3⁄8

C 1 3⁄4 x 1 3⁄4 max

D 11⁄16 3⁄4 1

E 5⁄16 3⁄8 3⁄8

F 13⁄16

G 2 2 3⁄8 2 7⁄8

Page 42: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

FUNCTION - The suspension of HVAC, Mechanical & Electrical services in an indoor stationary setting.

APPLICATION - Ideal for single or multi-tiered installations and low void ceilings. Especially designed for suspending services either within or exiting plant rooms. Available in a kit with cable and choice of pre-attached end fixing.

LOAD RATING - The No.4 Trapeze hanger has a 5:1 safety factor.

MATERIAL SPECIFICATION -No.4 Trapeze Fastener:1) Housing Type ZA2 Zinc2) Wedge Sintered steel hardened to min. 56 Rockwell C3) Spring Stainless Steel (Type 302)4) End Cap Acetal (MFI 25-27)

Cable: Galvanized high tensile steel cable to EN12385. Standard lengths from 5 ft - 30 ft, other lengths can be made to order.

Dimension Size (in)

A 1 3⁄4B 1 3⁄16

C 2 9⁄16

D 13⁄16

E 1 3⁄16

Single channel Gripple fastener for use with No.4 Gripple wire:

Size: No.4

Max. Safe Working Load: No.4 - 495 lbs

PRODUCT INFORMATIONNO.4 TRAPEzE FASTENER

SIzE SPECIFICATION APPLICATION

Submittal Data

Gripple Inc | 1611 Emily Lane | Aurora, IL 60502 | USA Tel +1 866 474 7753 Fax +1 800 654 0689 email [email protected]

www.gripple.comPI-77-US-SUBMIT

No.4

Cable Diameter (in.) 3⁄16

Strand configuration 7 x 19

Min. breaking load (lbs) 2,475

Max. safe working load (lbs) 495

Tensile strength (lbs/sq. in.) 256,700

C

ED

A

B

Page 43: SUBMITTAL DATA - Connective Systemsconnective-systems.com/userfiles/977/MEP-Catalogs/G... · 2016-01-23 · End Cap UV stabilized homopolymer polypropylene Cable: Galvanized high

Independent Vibration Testing of Gripple Hangers

Environmental Engineering Components (UK) Ltd conducted a series of tests to establish the relative performance of Gripple hangers compared to other suspension systems in limiting vibration transmission. The following is a summary of this testing. Methodology The tests were carried out on a rigid ‘goal post’ frame manufactured from rolled hollow section welded together with gusset plates welded at each joint, top and bottom. A 600mm section of 160mm diameter spiral duct was suspended from the frame using:

1. An 8mm dia. threaded rod and duct clamp. 2. An 8mm dia. threaded rod and with a neoprene lined duct clamp. 3. An 8mm dia. threaded rod and duct clamp with a neoprene anti vibration mount. 4. A No1 Gripple hanger with a stud end 5. A No2 Gripple hanger with a stud end 6. A No3 Gripple hanger with a stud end

A 20mm dia. x 30mm long steel cylinder with an oscillating motor acted as a vibrations source. The vibration source was placed on top of the spiral duct and set to oscillate at frequencies (1) Below 1 Hz (2) 1Hz (3) 3Hz. Using a Bruel and Kjaer type 2511 vibration metre with a 4370 accelerometer, displacement readings were taken at:

(A) the junction of the duct and suspension (B) the top of the frame.

Results From these readings comparative percentage isolation values were derived using the formula:

Displacement at (A) - Displacement at (B) = % isolation (absorption) Displacement at (A) Averages of these values showing the relative % isolation (absorption) effectiveness against vibration through the different products and their ranking are summarised below:

1st Gripple Hangers

77%

2nd Threaded Rod- with Anti vibration fixings

59%

3rd Threaded Rod

52%

Conclusions The main findings of the tests conducted were: 1. Gripple hangers provide better isolation against vibration than threaded rod across all frequencies up to 3 Hz 2. Gripple hangers provide better isolation against vibration than threaded rod with anti vibration fixing at

frequencies up to 1Hz 3. Gripple hangers provide better or equal isolation against vibration across all frequencies up to 3 Hz References Vibration testing of suspension systems – EEC (UK) Ltd. November 2002

A

B)