SUBJECT: No: TSB-16-13-001 ECM …Page 2 of 12 TSB-16-13-001 ECM REPROGRAMMING CHART Database No....

of 12

MITSUBISHI MOTORS

Technical Service Bulletin SUBJECT: No: TSB-16-13-001

ECM REPROGRAMMING FOR HARD TO RE-START DATE: January, 2016

ENGINE WITH LOW COOLANT TEMPERATURE MODEL: 2014-15 Outlander

CIRCULATE TO: l[JGENERALMANAGER I [ l PARTS MANAGER I [ X l TECHNICIAN

[ X] SERVICE ADVISOR I [ X l SERVICE MANAGER I [ X l WARRANTY PROCESSOR I [ l SALES MANAGER

PURPOSE Affected vehicles may exhibit a condition where the engine is hard to re-start if engine coolant temperature is low. Due to inappropriate programming in the engine ECM, if the coolant temperature is between 32 - 68 °F (0 - 20 °C), a hard to re-start condition may occur.

This TSB instructs dealers to reprogram the ECM with new software that will resolve this concern.

AFFECTED VEHICLES • 2014 and 2015 Outlander vehicles (US and Canada) equipped with 6B31 V6 3.0L engines

REQUIRED OPERATIONS 1. Confirm your MUT -Ill is updated with the latest reprogramming database.

2. Reprogram the ECM with the new software. Refer to the ECM Reprogramming Chart for new software information.

IMPORTANT: If an affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated before reprogramming. and DTCs are listed in the ECM memory, diagnose and repair those DTCs per the service manual before reprogramming. DO NOT reprogram the ECM until the reason(s) for other DTCs being set is corrected.

EQUIPMENT

The following equipment is needed to reprogram the ECM.

• VCI (Vehicle Communication Interface) or VCI Lite - MB991824 or MB992744.

• MEDIC Laptop/Tablet with A/C power adapter - 520924, or FZG1 MK2.

• MUT-III main harness 'A' (blue connector at the DLC end) - MB991910 or MB992745.

• USB 2.0 cable - MB991827 or MB992747.

• "Engine Compartment/Control Module" label - p/n MSSF024G00.

• MEDIC 3/4 update at 357 or higher.

• For Standalone MUT -Ill units, MUT -Ill Reprogramming Database N15112 or higher.

Copyright 2016, Mitsubishi Motors North America, Inc. Continued

The information contained in this bulletin is subject to change. For the latest version of this document, go to the Mitsubishi Dealer Link,

MEDIC, or the Mitsubishi Service Information website (www.mitsubishitechinfo.com). (4373)

of 12

TSB-16-13-001

ECM REPROGRAMMING CHART

Database No. 15112

ECU Part Software Part Number Model Number Data No.

Previous New

2014 Outlander 1860B805 1862C371 ZM1024-13 ZM1024-14 {NAS, GF4W, 6B31, AT)

2014 Outlander 1860C221 1862C372 ZM1063-03 ZM1063-04 {Canada, GF4W, 6B31, AT)

2015 Outlander 1860C554 1862C373 ZM1162-01 ZM1162-02 {NAS, GF4W, 6B31, AT)

2015 Outlander 1860C555 1862C374 ZM1163-01 ZM1163-02 {Canada, GF4W, 6B31, AT)

REPAIR PROCEDURE

NOTE: Reprogramming the ECM with the latest database (e.g., N15112) includes all past and current reprogramming for TSBs of affected vehicles. It is not necessary to reprogram the ECM for each previous TSB.

1. Check the underside of the hood to verify there is no "Authorized Modification" label (see step 19 in the Reprogramming Procedure for example) previously installed to indicate this reprogramming has already been completed. If a label is present and the "ROM ID#" on the label matches the "New S/W Part No." in the table above, the ECM is at the latest level and reprogramming is not necessary. Conduct normal diagnosis for the described condition.

For MEDIC 3/4 users only: (MUT -Ill users go to step 5)

2. Verify the MEDIC 3/4 is at version 3.5 and at update 357 or higher.

If your MEDIC 3/4 update is at least 357, continue with the Reprogramming Procedure on page 4.

If your MEDIC 3/4 update is below 357, update your MEDIC as follows.

F S:w,t,,,,fur!c:UQI' / EC V fl:epiQg, amml rici / Ou.1banfil10l1play(CANj

10GCOOIMl2 I lll60C:OJII

,...a.,,. • ., ... ,. •• , ... , "" ~-l<Nv"__,,......\11) :::::;;;;:.• ... ..,..,.,1 ,,n,. .. .,_o

IIIWC0l601 11f11WfC(MHICEl'i8'Cll'(!MCl(•I ,,..

:=:~: ~r l~:::".~..:! -=

:::::~ ~~~==-·:·; .. ; -

of 12

TSB-16-13-001

3. Select the MEDIC 3/4 Admin tab and click on "Updates."

4. IF the MEDIC update screen advises updates are available, click the "Begin" button. After all updates are complete, GO TO THE REPROGRAMMING PROCEDURE ON PAGE 4.

5. STANDALONE MUT-111 SCAN TOOL VIEWER (STV) ONLY: (MEDIC 3 USERS GO TO THE REPROGRAMMING PROCEDURE ON PAGE 4). Verify that your MUT -Ill has the most current version of the reprogramming database: From the MUT-III Main Page:

• Select "Special Function"

• Select "ECU Reprogramming"

• Select "Database File Display-CAN"

• Confirm the database number displayed at the top right of the chart is N15112 or higher

• If the database number displayed on your MUT-III is N15112 or greater, continue to the Reprogramming Procedure.

• If the reprogramming database number displayed on your MUT -Ill is lower than N15112, locate the reprogramming CD containing database N15112 and follow the instructions provided with the CD to update your MUT-II1.

of 12

TSB-16-13-001

REPROGRAMMING PROCEDURE

I & CAUTION I To ensure that the vehicle battery maintains 12V during the procedure, hook-up a battery charger to the vehicle during the procedure.

1. Connect the equipment as follows:

• Turn the MEDIC PC/tablet on. If the battery indicator in the lower right hand corner of the screen does not show a full charge, it is recommended that either the battery be charged prior to beginning, or be used with the A/C power adaptor connected.

• Connect the USB cable to the VCINCI Lite.

• When the laptop/tablet displays the MUT -Ill main screen, connect the USB cable to the device.

• Connect the MUT -Ill main harness with the blue DLC connection to the VCINCI Lite.

• Connect the blue connection of the MUT -Ill main harness to the vehicle's data link connector.

• Turn the VCI power switch ON . Verify that the indicator lamp in the upper right corner of the screen is green.

NOTE: VCI and MEDIC 3.5 Laptop shown for illustration purposes only.

MEDIC 3.5 I MUT -Ill MAIN HARNESS

Ill 0======::::Q I ~~~

BLUE END

VCI\VCI Lite

MEDIC 3.5 I MUT -Ill PC

2. Turn the ignition switch to the "ON" position.

System select Spee,al functioc I

CAN bus diagnosis

=':'=.~~='"·~-----. -::=..:-_.,.-.. -,,i-, ... =litl---[llaog __ .. ...,. .... . E!J T1'14111<11keo1R, admallu-L ~

~" '"----· .. · ···-~---·--·-·- · i;;;;.J • lntr,:,dod,,nollha•op

Pl e I tfu ctioli V 3401

~ ' ~ 0 J69 I ! t, i:1 ,,.. t I •

3. If using MEDIC, from the main page, click the MUT-111 STV icon at the top center of the screen to open MUT-111.

System select

CAN bus diagnosis

.0.,_101~

Dlil'l-•-•IIP<'ti.cl,~

l l'HifKl!iwolll • ad malllJ ll<llut,L ~

ECU reprogramming

V,CJ, SU1nd--t1lone Dingno~ (Data Transfer to PC-card)

PHEV Computer Dillgnosis

Automatic Reprogramming (K~ine)

Database File Display (K--line)

Spe-::fal function

Configuration

To ,

1.1se,(lll..aton!Q<V.C:.u.1ot. l!iJ

1..., .. .....,.,.v,CJ..1..-.i......-11,,.~ ~~ollc,n r..,. 11,o-·~,:,l--.!!I

SWSmonitor Drive Recorder (Display ontw-)

Aft CTCs

MiEV Computer Oiagnos~

Automatic Reprogramming (CAN) ______ ,_ _ ___J

Database File HI

The lo11owmg function is for K-line commur1ication's Reprogramming

Search Memory card transfer

Reprogramming Data Selection

s,.....Lllt No. SystemNilme OPC Option Name Witt, Optiori

I MFI

2 ELC--AT/CVT/TC-SST /

3 ECPS/4WS

4 !ABSIASCIASTCIWSS

5 SRS-AIR BAG ... 6 IA,irCondilioner

of 12

TSB-16-13-001

4. Go to the MUT-111 home screen and click on "Special function."

5. Select "ECU reprogramming."

6. In ECU reprogramming, select "Automatic Reprogramming (CAN)."

7. Press the model information display button (car icon) and verify that all vehicle information is correct.

• If vehicle information is NOT correct, follow steps a - c below.

• If vehicle information is correct, click the check mark at the bottom of the page, then go to step 8.

of 12

TSB-16-13-001

COSTIN ~1

MMN

\/IN _ 2 H8

TYPE _J GF4

CLASS J XLDV:ZLlf

66)1 ()0,S-<I M~l 1.IVECJ

TRANSMISSI~ WiJl<JAt6A/T-4WD)

2 3 4 5 6

w E R T y

s D F G H

X B N

DESTIN ] 1.wNA

VIN I JA4JZ4A.X11:"200!173C'1

CLA88 J XLDVZl.lt

MODEL YeAR ] 2ms

MODe:L _] OVTlANDt:H (G~.lll

0

7 8 9

u 0

J K L

M

0

p

a. If the VIN or vehicle description displayed does not match the vehicle you are working on, click the eraser icon at the bottom of the page to erase vehicle data. Then click the "VIN" button.

b. Click the icon in the lower RH corner of the screen to have MUT -Ill automatically read the VIN.

If a message appears saying the VIN cannot be input automatically, manually enter the 17 digit VIN into the VIN field at the top of the page.

Make sure the VIN is correct and click the check mark.

c. Confirm all data matches the vehicle, then click the check mark at the bottom of the page.

IMPORTANT: If an affected vehicle has a Malfunction Indicator Lamp (MIL) illuminated before reprogramming, and DTCs are listed in ECM memory, diagnose and repair those DTCs per the applicable service manual before reprogramming. DO NOT reprogram the ECM until the reason(s) for other DTCs being set is corrected.

_,.,. "' --' "'' ' ELC-ATiCv'TfTCSST

3 ABS(ASC'ASTC/1,VSS

' SRS,AREl,l,(j,

' .lurCon;l,t1ontr

' '=TACS

A ,-1_

I

...

/ f--+------lf-----;

of 12

TSB-16-13-001

8. "MFI" should be highlighted by default. If not, click on it to highlight it. Click the check mark to continue.

NOTE: In the next step, if the "pop-up" box does not appear, change "Tab" to TIR then back to MUT-111 (the pop-up box should then appear).

.----_,- .,.- ,J) Automa~ic s~arcn the <1-rua .

No ~t.falnli

' ""'

1~vff11I 1--1---·--·

"11tomr.lc:n.an;:hlNA...-o'iJ~~ng Clll :11 . C:hKk th• V.C.I. !Ind l'III IIHIH connttmg tt+n pr•:n tn• Ct'i: t>unan.

I

,_..,. , ~ A.tJtom:ahc searching the data. ... -- :S:.ilftftlngffjlfOgt~ lllllfMt dfll • . . "''

' ELC--ATICVT/TCSST

3 ABS/ASCIASTC/lo,,ss

~ I II Ii ' SI'S-"'"'°

' .llrCondolXIOlf ... I I I ' ETALS. I I

-

i,,,~-.. "'°""'

I

I

-

9. A message will advise the system will "Automatic search the data."

Click the check mark to continue .

of 12

TSB-16-13-001

IF ECU IS ALREADY AT LATEST VERSION

,__ __ .,__...,._ .._i) Comol@te re-progtamm1ng . .,_, ....

!CU~ 11.!ie11 tty , t i:tia 111111:11 fuhr..lllli lnMUT.a 41 11>,1iD11H. --

F---'' ='"""= -= -=-.<.--''=cu=••,=""'='"•=min11,_, .-.utiomlt!c R1prognmmlnglCANJ

System: MFI ECU Part No.: 1860C554 S/lN Part No.: 1860C55400 CD Vet.:Nf5 11 2

-U:UP... -::- -ClitlWt CIJP!N CWINIUM'f'III~ COtllltlU I 1~4 1~55-IQ I lUQC554 11$X:5541111 1,0VTV,t,OERQJl$fla'li:C~T /

=~·::;:;:7N~~· 1 t"'"""_..,.,_.,_,,,.,.

Sy&tem: MFI ECU Part No.: 1860C554 ~-------"'S/W!!,! .: 1860CS5400 CDVer.:N1 5112

C.,,1t11lCIJ"'" Qllqnle,wPi'l"'O =- I ~, ltelt:31l ~ , ~ I~ 1'0U1'\..'UIERNl11S411'1K~T /

lllliiiiilllilliiiiilii;'_::"£~=zi~ I (!) Check reprogramming data

Reprogfflffl ECU_ OK? F~e Name : 1862C373.cff

S,-.lemllJnr:tlQn / ECU Riep,o;irammlrw;i / Automati c Rt programming jCANI

Now Reprogrammiri1, JS%

I

O.._ECU_.._....,.,_.

11 II II I I ~I I I I

If the message seen at left is displayed, the ECU software is already at the most current level. Do not continue with the reprogramming procedure. This TSB does not apply.

Click the check mark to clear the window, then click the Home icon at the lower left corner of the screen to return to the System Select main page.

Turn the ignition switch to the OFF position and disconnect the MUT -Ill. Turn off and disconnect the battery charger. Conduct normal diagnosis per the service manual.

If a "Complete Reprogramming" message does not appear, continue with the reprogramming procedure.

10. The Automatic Reprogramming (CAN) database screen will display.

• Verify that the new ECU and S/W part numbers are listed in the table.

• Confirm the database number at the top right of the table is N15112 or higher.

• If more than one row is displayed in the table, refer to the ECM Reprogramming Chart on page 2 to highlight and select the correct row.

• Click the check mark to continue.

11. The "Check reprogramming data" window should appear with the new file name.

NOTE: Refer to the ECM Reprogramming Chart on page 2 for the new file names.

12. Click on the check mark in the pop-up box to initiate the reprogramming.

13. Once the reprogramming is initiated, the screen as shown will indicate the reprogramming progress.

NOTE: Do not disturb the cables or turn off the ignition during reprogramming.

of 12

TSB-16-13-001

!&CAUTION I The Daytime Running Lights and both the engine and condenser fans will automatically be turned on during reprogramming. Care should be taken to insure nothing gets caught in the moving blades. The radio will be turned off and you will also hear a chime in the interior for a short period of time. These are normal conditions.

© Completed

On board ECU hos ~rammed. To finish r1prog11mmrn; . tum OFF 1G 1wttcnror1:lea1!8second1. ECU Pan No.:1860C554 SNJ Pmn No.:18&1C55401

if __ ·_ tlffllfllnedon ECUR 9P1" Qgrammln11

Automatic Reprogramming (K~ine) Automatic Reprogramming (CAN)

DatabaMt File Display (K--iine) Database File Display (CAN)

The lollowmg function is for K-line commu nication's Reprogra mming

Search Memory card transfer

Systffil select Special functioo

CAN bus diagnosis ConfigtXation

-~ -:~1-~,w~------.r'T =·"~-~ ----

ci., ,...il<J•u• .... ••,J•,.•-~ ... llS8 u ....,...., 1.,v.c.u1 ... ~ lli!Nol,,c,J..., olV.(J..t, hflH,eli.a ,,111)1. ~

E•pl i~..,1.,. l+I "'4 .,......in9 ~I""~.,~. ,. ~

., ~-'""""'1.,, 1-1 ~ •• ..,.~Mlilfffn, •~• o ... ~ !Hl. ~

14. Reprogramming is completed.

a. Verify that the S/W Part No. Is correct.

b. Click on the check mark.

c. Turn OFF ignition switch for at least 8 seconds.

d. Turn ignition switch ON, then proceed to the next step.

15. Click on the "home" button.

16. Perform an "Erase and Read all DTCs."

a. Select "Special function."

of 12

TSB-16-13-001

systemrunctton

Drive Recorder (Display only)

ECU reprogranvning

V.C. I. Stand-alone Diagnosis (Data Transfer 10 PC-card)

S ffllflllunctlon AII OTCa

Read all OTC& J

.. SvllNffi~ / AJIDTC1 / EnlHand RHd al DTC1

_,,.,. """ -- -~,_BAG i. ., l°"rCon:lb(w)er

A

., f[ACS i.

" .. - ., " isi~~Ser$DI

" .... .,

" pss .,

SWSmonitor Drive Record..,. (Display on ivt

All DTCs

Erase and Read al DTCs

Model Ye,111 Up to2005MY

From2006MY

I --"""""""' I

I.IOOelVear

""""""" Loei:ll'IQ()OIOl3el0

OPC OplioaN•me -""" ""tl!QIAF.AS.T "

""' ~lllfAST.

~ s~1ec1 criecKtng ,ys1erns. \ , c1opllon.

...... I

!i'l ll ~ ll II ~ II lil I ~/ l1 a 11 ' I

I

I ,_ -

J

b. Select "All DTCs."

c. Select "Erase and Read All DTCs."

d. The "System List" on the left side of the screen will have all selections checked. Do not change these selections. DTCs may be set if the vehicle is equipped with options that are unchecked.

e. Click the check mark to continue.

.. Sv11ffllfunclk>n / AJ I DTC1 / EnlHandR1adalDTC1

_,,.,. ModelYe;a1 Up to2005MY

""" ,,...,..,. - From2006MY

., SR~BAG ')- .. --.. '"""-'- \V 1 .. __.J~N:11'!'11! I ~,,,,, '\,oel 'TMr I

ETACS \ ...... ~ ~VJ.,. I ..

I t~Opa(wl~

~ - OPC Opcioathme _ _,

T SleenngArq,eSen$0r w, ct,w: F AS T "

"' T VF; lh F AST.

., oss T .._

se-1ect er.eek Ing s.ys1ems. _\ :N71'<10p1100.

J!(-1 11 ~ 11 1l 1£h II ilJ 11- -/ I a 11 11 r I

·1t.tmfunction A!IOTC.. Er11111 1r1d Ral<IUOTC1

-"" I I Oit,gllQIICW111dtcode(SJ

""" ,,,.m..,. I RH"" I l= I ·- .... ~· - - I I I I _..orc,. - w.....,.o,q

~C-AT/CVTfTC.SST Q;) AJI DTCs ~ RUSE COHTROl

All &ruing and chec!(s are completed

~CPSI.-WS

r? ,e

ts,:lS-AIRBAG

IA,1 CoMilioner tllc,,"II II II II ...... I Now Checking! I

,/ ;,---- I

·~

I I

7 I

of 12

TSB-16-13-001

NOTE: If, in some cases, the check mark button at the bottom is not active, perform the following:

1) Select the System name that is underlined (for example, TPMS, as shown on left).

2) Select the appropriate option for the vehicle. Repeat steps 1 and 2 for all underlined systems.

3) Click on the check mark. Wait until MUT-111 is finished and click the check mark again to confirm.

f. A window will pop up asking you to confirm OTC erasing. Click the check mark for OTC erasing and reading to begin.

17. When OTC erasing is completed, click the check mark in the pop-up message that reads "All erasing and checks are completed."

a. If DTCs return after reprogramming, click the check mark to clear the window. Diagnose and repair per the Service Manual.

b. If DTCs do not return, click the check mark to clear the window, then click the home icon at the lower left of the screen to return to the main menu.

18. Turn off the ignition switch and disconnect the MUT -Ill. Turn off and disconnect the battery charger.

19. Using a ball-point pen, enter the appropriate ECU part number, Software Part Number (ROM ID#), this Technical Service Bulletin number, your dealer code, and the current date on the Engine Compartment / Control Module Label (p/n MSSF024GOO). The Vendor Code is not applicable. The label is available from your facing PDC.

• AUTHORIZED l'.~!~J!ll!~J;!~ MODIFICATIONS

PARTNUMBER 1860C297

TSB

ENG TSB-14-13-XXX

AIT En ine Com artment Label

DATE 06/25/14

NOTE: The Control Module Label is NOT used for this reflash. It should be discarded.

of 12

TSB-16-13-001

20. Carefully remove all dirt and oil from a vacant area near the VECI label on the underside of the hood and affix the Engine Compartment Label (LH side, above) to that area.

21. Test drive the vehicle to confirm proper operation and the MIL does not illuminate. Diagnose and correct any DTCs that return.

PARTS INFORMATION Use only the Genuine Mitsubishi Parts listed below.

Description

Label, Engine Compartment

WARRANTY INFORMATION

Part Number

MSSF024G00

Quantity

1

This bulletin is supplied as technical information only and is not an authorization to repair. If an affected vehicle is reported with the described condition, diagnose the condition, repair as described in this bulletin and submit a normal warranty claim using the following information.

Nature Code: 02B Cause Code: 605

Labor Operation No.: 13850113 Time Allowance: 0.3 hrs.

Warranty Coverage: 8/80 Emissions Coverage

SUBJECT: No: TSB-16-13-001 ECM …Page 2 of 12 TSB-16-13-001 ECM REPROGRAMMING CHART Database No....

Documents

Transcript of SUBJECT: No: TSB-16-13-001 ECM …Page 2 of 12 TSB-16-13-001 ECM REPROGRAMMING CHART Database No....