STUMP GRINDERSthese rugged teeth, which last longer and typically only need 2 or 3 replaced at a...

STUMP GRINDERS

FEATURES

THE RIGHT EQUIPMENT

Like the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable, gravel, stones even metal posts are not uncommon to “find”. Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust.

Carbide Tipped

Many hands make light work, or in this case fine mulch faster and easier. The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of these rugged teeth, which last longer and typically only need 2 or 3 replaced at a time. The bolt-on designed teeth allow for straightforward replacement.

More Teeth

The Stump Blaster’s carbide teeth extend a full1 1/4 inches from the rotor. This prevents chips and mulch from getting plugged up during grinding. Greater chip clearing produces smoother operation and reduces heat build-up that could damage the rotor and cause premature tooth failure.

More Clearance

Go with the Flow.

Make sure you adjust your flow control. This control allows you to adjust the cutting sweep to get the smoothest cut possible, the full return allows you to return to the start of the cutting sweep as quickly as possible.

The Flow Control allows you to fine tune the cutting pass speed, to match the size and performance of your tractor.

Flow Control

The 540 PTO driven Stump Blasters are designed for 3 point hitch mount to your 20-85 HP tractors.

The 3P40 requires a 60-120 HP tractor with a 1000 RPM PTO.

PTO

This optional control is mounted on an adjustable arm for optimal placement. The control is recommended for smaller tractors with limited HP for better cutting control and for tractors with only one remote .

External ControlPart #S1050

The massive 3/4 inch thick steel rotor provides the back bone for the Stump Blaster Cutting system. It is the anchor for the carbide tipped teeth. For smooth operation it is important that the rotor remains solid with no flexing. The impressively rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.

Rotor

The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way.

Floating Deflector

The heavy duty base provides a solid base for grinding. This allows for more consistent grinding performance and reduces the stress on your tractor.

Stabalizer Base

The rugged gear box transfers power from the tractor’s PTO to the rotor creating 803 Ft.-Lbs of torque turning the rotor and hungry teeth at 810 RPM.

Gear Box

OPTIONAL

PTO STUMP BLASTER

THE RIGHT EQUIPMENTTHE RIGHT EQUIPMENT

Specifications

Cutting Depth

Above Ground: 10”Below Ground: 6”

Model No. 1P24Recommended HP Size 20-45Maximum HP Size 50Hydraulic GPM --Rotor Size 24"Number of Teeth 34Tooth Construction Carbide Steel Bolt-in

Cutting Wheel Speed 540 RPMCutting Height - Above Ground 10”Cutting Depth - Below Ground 6”Maximum Cutting Depth - Per Pass 5”Maximum Horizontal Cut 22”Swing Arc 0ºHub Torque 803 Ft.-Lbs.Over Torque Protection Shear boltHitch Cat INo. Of Remotes Required - Hydraulic 0Requires 12 Volt DC NoInput Speed 540Unit Weight (Shipping) Lbs. 350Width (Shipping) 32”Length (Shipping) 32”

TIP 1P24

Just like your mom told you. Take small bites and chew.

The best results and smoothest operation are achieved by easing into the stump a little at a time and allowing the self-feeding hinge to do its job.

Cutting Depth


65º

Specifications

Model No. 3P24Recommended HP Size 30-50Maximum HP Size 60Hydraulic GPM 5-20Rotor Size 24"Number of Teeth 34Tooth Construction Carbide steel bolt-in

Cutting Wheel Speed 810 RPMCutting Height - Above Ground 18"Cutting Depth - Below Ground 8"Maximum Cutting Depth - Per Pass 6"Maximum Horizontal Cut 22"Swing Arc 65ºHub Torque 803 Ft.-Lbs.Over Torque Protection Slip clutchHitch Cat I or IINo. Of Remotes Required - Hydraulic 1 or 2Requires 12 Volt DC NoInput Speed 540Unit Weight (Shipping) Lbs. 902Width (Shipping) 40"Length (Shipping) 49"

TIP

Go with the Flow.

Make sure you adjust your flow control. This control allows you to adjust the cutting sweep to get the smoothest cut possible, the full return allows you to retrun to the start of the cutting sweep as quick as possible.

FLOW

Specifications


Cutting Wheel Speed 810 RPMCutting Height - Above Ground 25"Cutting Depth - Below Ground 14"Maximum Cutting Depth - Per Pass 9"Maximum Horizontal Cut 32"Swing Arc 65ºHub Torque 803 Ft.-Lbs.Over Torque Protection Slip clutch Hitch Cat. IINo. Of Remotes Required - Hydraulic 2Requires 12 Volt DC NoInput Speed 540Unit Weight (Shipping) Lbs. 1231Width (Shipping) 48"Length (Shipping) 54"

THE RIGHT EQUIPMENT

Cutting Depth


65º

TIP

Take Note.

It’s a good idea to get down and inspect the stump and surrounding area. Make a note of where exposed roots are, they can be difficult to locate once you start grinding.

INSPECT

Specifications


Cutting Wheel Speed 1000 RPMCutting Height - Above Ground 25"Cutting Depth - Below Ground 14"Maximum Cutting Depth - Per Pass 9"Maximum Horizontal Cut 32"Swing Arc 65ºHub Torque 1050 Ft.-Lbs.Over Torque Protection Slip clutch Hitch Cat. IINo. Of Remotes Required - Hydraulic 2Requires 12 Volt DC NoInput Speed 1,000Unit Weight (Shipping) Lbs. 1283Width (Shipping) 48"Length (Shipping) 54"

Cutting Depth


65º

TIP

Dry Up.

Try to grind when the surrounding soil is dry. Once you get below grade it is easier to grind in dry soils. Muddy dirt can slow down your grinding and lengthen the clean up process.

SOIL

3-Point Hitch Stump Cutting Times

3-Point Hitch Model Comparison ChartModel No. 1P24 3P24 3P34 3P40Recommended HP Size 20-45 30-50 50-75 60-120Maximum HP Size 50 60 80 125Hydraulic GPM -- 5-20 5-20 5-20Rotor Size 24" 24" 34" 34"Number of Teeth 34 34 54 54Tooth Construction Carbide Steel Bolt-in Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in

Cutting Wheel Speed 540 RPM 810 RPM 810 RPM 1000 RPMCutting Height - Above Ground 10” 18" 25" 25"Cutting Depth - Below Ground 6” 8" 14" 14"Maximum Cutting Depth - Per Pass 5” 6" 9" 9"Maximum Horizontal Cut 22” 22" 32" 32"Swing Arc 0º 65º 65º 65ºHub Torque 803 Ft.-Lbs. 803 Ft.-Lbs. 803 Ft.-Lbs. 1050 Ft.-Lbs.Over Torque Protection Shear bolt Slip clutch Slip clutch Slip clutch Hitch Cat I Cat I or II Cat. II Cat. IINo. Of Remotes Required - Hydraulic 0 1 or 2 2 2Requires 12 Volt DC No No No NoInput Speed 540 540 540 1,000Unit Weight (Shipping) Lbs. 350 902 1231 1283Width (Shipping) 32” 40" 48" 48"Length (Shipping) 32” 49" 54" 54"

Model 20 Hp 30 Hp 40 Hp 60 Hp 70 Hp 80 Hp 90 Hp 120 Hp1P24 12 min 10 min 8 min -- -- -- -- --3P24 -- 8 min 6 min 5 min -- -- -- --3P34 -- -- -- 3 min 2 min 2 min -- --3P40 -- -- -- 3 min 2 min 2 min 2 min 2 min

Model 20 Hp 30 Hp 40 Hp 60 Hp 70 Hp 80 Hp 90 Hp 120 Hp1P24 30 min 20 min 15 min -- -- -- -- --3P24 -- 15 min 12 min 10 min -- -- -- --3P34 -- -- -- 6 min 5 min 4 min -- --3P40 -- -- -- 6 min 5 min 4 min 3 min 2 min

Model 20 Hp 30 Hp 40 Hp 60 Hp 70 Hp 80 Hp 90 Hp 120 Hp1P24 -- -- -- -- -- -- -- --3P24 -- 45 min 40 min 35 min -- -- -- --3P34 -- -- -- 20 min 15 min 15 min -- --3P40 -- -- -- 20 min 15 min 15 min 10 min 8 min

12”

12”

12”

12”

30”

48”

THE RIGHT EQUIPMENT

Skid Steer Stump Cutting Times

Model MotorOption

10 GPM 12 GPM 15 GPM 20 GPM 24 GPM 30 GPM 35 GPM 40 GPM

S14 S250 15 min 10 min 8 min -- -- -- -- --S450 18 min 12 min 10 min 6 min -- -- -- --

S18 S450 20 min 15 min 12 min 10 min -- -- -- --S550 20 min 15 min 12 min 10 min 8 min -- -- --S650 -- -- -- -- 15 min 7 min 6 min 5 min

S24 S450 -- -- -- 20 min 12 min -- -- --S550 -- -- -- 20 min 12 min 10 min 8 min --

S28 S650 -- -- -- -- -- 6 min 5 min 4 minDouble all sizes for intermittent.

12”

12”

12”

12”

24”

36”

Model MotorOption


S14 S250 30 min 20 min 12 min -- -- -- -- --S450 40 min 25 min 15 min 10 min -- -- -- --

S18 S450 50 min 30 min 20 min 15 min -- -- -- --S550 50 min 30 min 20 min 15 min 10 min -- -- --S650 -- -- -- -- 20 min 15 min 12 min 10 min

S24 S450 -- -- -- 35 min 25 min -- -- --S550 -- -- -- 35 min 25 min 20 min 15 min --


Model MotorOption


S18 S450 -- -- 60 min 40 min -- -- -- --S550 -- -- 60 min 40 min 30 min -- -- --S650 -- -- -- -- 45 min 20 min 15 min 15 min

S24 S450 -- -- -- -- 50 min -- -- --S550 -- -- -- -- 50 min 40 min 30 min --


FEATURES

THE RIGHT EQUIPMENT

This 12V remote allows you to control your Stump Blaster from within the cab of your skid steer.

This remote comes standard with S24 and S28 models.

The Stump Blaster’s carbide teeth extend a full 1 1/4 inches from the rotor. This prevents chips and mulch from getting plugged up during grinding. Greater chip clearing produces smoother operation and reduces heat build-up that could damage the rotor and cause premature tooth failure.

More Clearance

Remote

The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way.

Floating DeflectorLike the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable, gravel, stones even metal posts are not uncommon to “find”. Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust.

Carbide Tipped

Many hands make light work, or in this case fine mulch faster and easier. The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of these rugged teeth, which last longer and typically only need 2 or 3 replaced at a time. The bolt-on designed teeth allow for straightforward replacement.

More Teeth

Skid steer mounted Stump Blasters run on hydraulic motors. For best results, match your equipments flow rate to one of our available hydraulic motor options.

Hydraulic Motor

The massive 3/4 inch thick steel rotor provides the back bone for the Stump Blaster Cutting system. It is the anchor for the carbide tipped teeth. For smooth operation it is important that the rotor remains solid with no flexing. The impressively rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.

RotorFloating Deflector Flow ControlFine tune the performance of your Stump Blaster with the Flow Control.

THE RIGHT EQUIPMENT

STUMP BLASTER

Specifications

Designed simply and ruggedly the S14 and S18 has a heavy duty fixed deflector. The simple direct flow hydraulic drive is designed to provide the best torque and RPM to the cutting head. The unique positioning of the rotor allows the operator an excellent view of the grinding action. The S18 is also available with a mini skid steer mount for even better access to tight areas.

THE RIGHT EQUIPMENT

Model No. S14 S18Recommended HP Size 12-30 25-80Maximum HP Size Check GPM &

PSICheck GPM & PSI

Hydraulic GPM Check Motor Options Check Motor Options

Rotor Size 18” 24”Number of Teeth 12 34Tooth Construction Green Carbide steel bolt-in

Cutting Wheel Speed 700 RPM 700 RPMCutting Height - Above Ground No limit No limitCutting Depth - Below Ground 6” 10”Maximum Cutting Depth - Per Pass 2” 5”Maximum Horizontal Cut 12” 22”Swing Arc 0º 0ºHub Torque 150 Ft.-Lbs. 250 Ft.-Lbs.Over Torque Protection Relieve valve Relieve valveHitch Mini Plate Quick AttachNo. Of Remotes Required - Hydraulic 1 1Requires 12 Volt DC No NoInput Speed -- --Unit Weight (Shipping) Lbs. 394 702Width (Shipping) 44" 48"Length (Shipping) 41" 48"

Cutting Depth

Below Ground: 10”

TIP

Grass saver. Since cutting is done by backing away from the stump, and repositioning is usually only a few inches, the S14/S18 causes very little turf damage in the hands of an experienced skidsteer operator.

S14/S18

Specifications

A 12V diverter valve allows the S24 to have not only a hydraulic drive but also a swing cylinder for a more refined cutting pass. This needle valve allows precise control of the cutting pass, and you to grind more of the stump without repositioning.

Model No. S24Recommended HP Size 30-80Maximum HP Size Check GPM &

PSIHydraulic GPM Check Motor Options

Rotor Size 24”Number of Teeth 34Tooth Construction Carbide steel bolt-in

Cutting Wheel Speed 700 RPMCutting Height - Above Ground No limitCutting Depth - Below Ground 10”Maximum Cutting Depth - Per Pass 6”Maximum Horizontal Cut 22”Swing Arc 80ºHub Torque 250 Ft.-Lbs.Over Torque Protection Relieve valveHitch Quick AttachNo. Of Remotes Required - Hydraulic 1Requires 12 Volt DC YesInput Speed --Unit Weight (Shipping) Lbs. 852Width (Shipping) 48"Length (Shipping) 56"

Cutting Depth

Below Ground: 10”

TIP

Size matters.

Matching the motor option to your skid steer could be the most important factor that determines your stump grinding performance, see page 14 for motor calculations.

SIZE

80º

THE RIGHT EQUIPMENT

STUMP BLASTER

Specifications

For high flow and higher HP skid steers the S28 adds a high volume hydraulic motor and a gearbox that increases the torque to the cutting head. Giving you the best of precision, power and speed in your grinding. The S24 and S28 ship with a convenient 12V cigarette lighter plug to power the diverter valve.

THE RIGHT EQUIPMENT

Model No. S28Recommended HP Size 50-120Maximum HP Size Check GPM &

PSIHydraulic GPM 30-40Rotor Size 24”Number of Teeth 34Tooth Construction Carbide steel bolt-in

Cutting Wheel Speed 800 RPMCutting Height - Above Ground No limitCutting Depth - Below Ground 10”Maximum Cutting Depth - Per Pass 6”Maximum Horizontal Cut 22”Swing Arc 80ºHub Torque 803 Ft.-Lbs.Over Torque Protection Relieve valveHitch Quick attachNo. Of Remotes Required - Hydraulic 1Requires 12 Volt DC YesInput Speed --Unit Weight (Shipping) Lbs. 995Width (Shipping) 48"Length (Shipping) 56"

Cutting Depth

Below Ground: 10”

80º

TIP TEETH

Broken-in teeth have less bite which makes cutting soft wood easier and reduces the chance of shattering the carbide against hidden rocks.

Model No. S14 S18 S24 S28Recommended HP Size 12-30 25-80 30-80 50-120Maximum HP Size Check GPM & PSI Check GPM & PSI Check GPM & PSI Check GPM & PSIHydraulic GPM Check Motor Options Check Motor Options Check Motor Options 30-40Rotor Size 18” 24” 24” 24”Number of Teeth 12 34 34 34Tooth Construction Green Carbide steel bolt-in Carbide steel bolt-in Carbide steel bolt-in

Cutting Wheel Speed 700 RPM 700 RPM 700 RPM 800 RPMCutting Height - Above Ground No limit No limit No limit No limitCutting Depth - Below Ground 6” 10” 10” 10”Maximum Cutting Depth - Per Pass 2” 5” 6” 6”Maximum Horizontal Cut 12” 22” 22” 22”Swing Arc 0º 0º 80º 80ºHub Torque 150 Ft.-Lbs. 250 Ft.-Lbs. 250 Ft.-Lbs. 803 Ft.-Lbs.Over Torque Protection Relieve valve Relieve valve Relieve valve Relieve valveHitch Mini Plate Quick Attach Quick Attach Quick attachNo. Of Remotes Required - Hydraulic 1 1 1 1Requires 12 Volt DC No No Yes YesInput Speed -- -- -- --Unit Weight (Shipping) Lbs. 394 702 852 995Width (Shipping) 44" 48" 48" 48"Length (Shipping) 41" 48" 56" 56"

Match GPM & PSI Results to a ModelModel Identifies Motor Option

Skid Steer Model Comparison Chart

S14 10-15 16 GPM No Included S250

12-22 23 GPM No Included S450

S18 12-22 23 GPM No Included S450

12-27 28 GPM Yes** Included S550

25-40 42 GPM Yes** Not Supplied S650

S24 20-26 28 GPM Yes** Included S450

22-32 35 GPM Yes** Not Supplied S550

S28 30-40 42 GPM Yes** Not Supplied S650

Model RecommendedGPM

Max.GPM*

Requires Case Drain

Hydraulic Couplers

Motor Options

*NOTICE: This value must never be exceeded or warranty is voided. Will cause equipment damage.

**Note required for bottom of GPM Range

TRENCHERSMULCHERS GENERATORSAUGER DRIVES TREE SPADES

Authorized Dealer

Manufactured by: MTB MFG. INC.

1.866.820.7603www.baumalight.com

4575 Powell Rd. Wallenstein, ON. Canada, N0B 2S0

EE

CI1

3217

-S01

-01

Prin

ted

in C

anad

a -

When you are ready to order the product you request sudden shipping. Baumalight will then quote and arrange the direct shipping.

As soon as the product is built to your order specifications, it is shipped direct to your dealer.

The product arrives atdealership ready for final set up and delivery.

ORDER SHIP RECEIVE

At Baumalight we are committed to getting the right product in the hands of the customer as soon as possible. To this end we created a subsidized shipping program that allows you order and get the right equipment, usually under 2 weeks. The program is as easy as 1, 2, 3.

Check www.suddenshipping.com for up to date times

FREEREPLACEMENT

TEETHOF

INCLUDED

STUMP GRINDERSthese rugged teeth, which last longer and typically only need 2 or 3 replaced at a...

Documents

Transcript of STUMP GRINDERSthese rugged teeth, which last longer and typically only need 2 or 3 replaced at a...