STSQuadThreadkorr5

Edition 2010.01

Scandinavian Tool Systems AB is a Swedish based manufacturer and supplier of tools for thread turning, thread milling, parting off and grooving. Our products are sold through distributors in more than 40 countries worldwide.

Table of contentGeneral information about the QuadThread system ....................................... 5 QuadThread External insertsPartial profile............................................................................................................................. 13 ISO Metric (M)........................................................................................................................... 14 MJ .............................................................................................................................................. 15 ISO Unified (UN)....................................................................................................................... 15 UNJ ............................................................................................................................................ 16 Whitworth (BSW, BSP)............................................................................................................. 17 BSPT .......................................................................................................................................... 18 Pansarrohrgewinde (PG).......................................................................................................... 18 Trapezoidal DIN 103 .................................................................................................................. 19 Round DIN 405 .......................................................................................................................... 19 Modul......................................................................................................................................... 19 ACME ......................................................................................................................................... 20 STUB ACME .............................................................................................................................. 20 NPSM......................................................................................................................................... 20 NPT ............................................................................................................................................ 21 NPTF Dryseal ............................................................................................................................ 21 API RD........................................................................................................................................ 22 API.............................................................................................................................................. 22

QuadThread External toolholdersToolholders ................................................................................................................................23 Clamping toolholders .............................................................................................................. 23 Cassette type toolholders ........................................................................................................ 23 Standard cassettes ................................................................................................................... 24 Extended cassettes................................................................................................................... 24 API cassettes ............................................................................................................................. 24 Small axial type toolholders ................................................................................................... 25 Cassette type axial toolholders ............................................................................................... 25 Blade cassettes ......................................................................................................................... 26 Drophead toolholders .............................................................................................................. 26 Screws, Keys ............................................................................................................................. 26 = Stock standard * = Limited stock

3

Table of contentQuadThread Internal insertsPartial profile............................................................................................................................. ISO Metric (M) .......................................................................................................................... ISO Unified (UN)....................................................................................................................... Whitworth (BSW, BSP)............................................................................................................. BSPT .......................................................................................................................................... Pansarrohrgewinde (PG).......................................................................................................... Trapezoidal DIN 103.................................................................................................................. Round DIN 405.......................................................................................................................... ACME ......................................................................................................................................... STUB ACME .............................................................................................................................. NPT ............................................................................................................................................ NPTF Dryseal ............................................................................................................................ API RD........................................................................................................................................ API.............................................................................................................................................. 27 28 29 30 31 32 32 33 34 35 36 37 38 38

QuadThread Internal toolholdersToolholders ............................................................................................................................... Tungsten alloy toolholders ...................................................................................................... Cassette-type toolholders ........................................................................................................ Standard cassettes ................................................................................................................... API cassettes ............................................................................................................................. Screws, Keys ............................................................................................................................. 39 39 40 40 40 41

QuadThread CBNThreading by hard turning ...................................................................................................... 42 Inserts for Partial profile .......................................................................................................... 43

QuadCutOffParting off and grooving .......................................................................................................... Inserts ........................................................................................................................................ Holders ...................................................................................................................................... Screws, Keys ............................................................................................................................. = Stock standard * = Limited stock

44 45 46 46

4

QuadThread - Threading the ingeniously simple wayQuadThread is an entirely different type of threading tool. Instead of the traditional horizontal triangular insert, this insert is positioned upright and has a square shape. The benefits are obvious: 1. The insert is much stronger. 2. The insert mounting is much more stable. 3. The insert has four cutting edges instead of three.

QuadThread offers maximum indexing accuracy, with support points strategically located.

The QuadThread system has very high indexing accuracy. This is due to a combination of: 1. The insert is precision ground,including the locating surfaces. 2. Large machined surfaces in the insert seat absorb and distribute the cutting forces in an optimized way. 3. The insert is locked in position by means of a large, sturdy center screw.

The insert seat serves as a Vee block fr the insert. The cutting forces are absorbed by large flat surfaces.

Strong and stableThe tool stability demands in threading operations are stricter than those in virtually any other machining operation. A very high axial load is applied at the instant when the insert enters the workpiece. But if a perfect thread is to be produced, the insert must remain immobile in its seat. With the QuadThread, you are assured that the insert will be firmly secured in position. The center screw - which is located a little off center - draws the insert into the seat and also presses it onto the large rear support surface to ensure that the cutting forces will be securely absorbed.

5

QuadThread - Threading the ingeniously simple wayThe slender toolholders for breadth of rangeThe threading operation must often be carried out in confined spaces, such as at workpiece shoulders or close to the chuck in bar automatics. In these situations, you can use the blade toolholder . The QuadThread insert is mounted upright, we can make the toolholder no more than .24 wide - with unimpaired stability. This is invaluable in confined spaces.

.24

The cassette system - economical and convenientAnother economical and convenient refinement of the QuadThread toolholders is the cassette system (from 5/8 upwards). You can use the same basic toolholder from 72TPI-4TPI. Only the cassette needs to be changed for the two different insert sizes.

Helix anglesThe seat gives the insert a helix angle of 1.5 as standard. For internal cassettes the helix angle is 0.7 as standard. Almost all the threads we produce (90%) have a helix angle of between 0.5 and 2.0, for which the standard angle can be used. But if you need other angles, we can accommodate those too.

Same insert for right-hand and left-hand threadsA further economic and practical benefit of the QuadThread inserts is that they can be used, in most cases, for both right-hand and left-hand threading.

6

Technical informationTHREADING TOLERANCESAll thread standards have dimensional tolerances to achive the required fit between the shaft and the nut. The shaft (in most cases) has a larger root radius and closer tolerance than the nut, which is designed to prevent shaft breakage. The standards for the ISO and UN (Unified) thread profiles are shown here.

Shaft

Rmin0.125P Rmax0.144P

0.25P

Nut

0.125P

P

PROFILESPartial profile inserts can be used for a variety of thread pitches and standards, providing the included angle is the same, however, incorrect nose radius on the insert can result in rejection of the component. This style of insert will not deburr the major diameter of the thread and will, therefore, require a secondary operation. Full profile inserts are designed to produce the correct root radius and depth requirements for an individual pitch. Tool life and thread quality are always improved when selecting this style of insert, because the thread profile and depth is dedicated to that pitch, therefore, fewer passes are required to complete the thread.

PARTIAL PROFILE

FULL PROFILE

WITH SMALL PITCHES

MULTI-TOOTH

.016-.024 With this insert threading can be produced much closer to the shoulder. Available for pitches 1mm (24TPI) and finer, and also produced in partial and full profile styles. Threading cycle times can be reduced up to 50% with this style of insert, and tool life is greatly increased due to fewer passes. More power is required when using this type of insert, therefore, a stable component and rigid setup are necessary. Chip control is much easier with this insert geometry, chips are divided into 3 manageable portions. The first tooth cuts the flanks of the thread, and the following tooth generates the root radius.

7

Technical informationCLEARANCE ANGLES

hread QuadT

The side clearance angles on QuadThread are generated by tipping the External insert 10, and the Internal insert 15 or 20. Note that the clearance angle is larger for ISO Metric, UN and Whitworth profiles than it is for Trapezoidal and ACME.

More care is required when selecting cassettes for Trapezoidal and ACME profiles, to ensure that the helix angle is as close as possible.

HELIX ANGLESOver 90% of all common profiles have a helix angle between 0.5 and 2. We have chosen 1.5 as the standard angle for QuadThread. In the diagram below the helix angle () is shown as a function of the diameter (D2) and the thread pitch (Ph). tan = x D2 Pitch TPI = 4.5 4 = 3 = 1.5 = 0 4.5 5 5.5 6 7 8 10 12 16 24 48 mm 10 Inch1/2

Ph

Pitch mm 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Diameter 20 1 30 40 11/2 50 2 60 21/2 70 3 80 90 31/2 100 4 110 41/2 120 5 130 140 51/2

150 6

OTHER HELIX ANGLESWhen threadingTrapezoidal and ACME profiles, or when producing a left hand thread with a right hand toolholder, cassettes other than the standard may be required. QuadThread cassettes are available in increments of 1.5 helix. The Internal Standard cassettes have 0.7 helix as standard.

=4.5

=3

=1.5

=0

=-1.5

=-3

QER 25-128

4.5

QER 25-12-

3

QER 25-12

QER 25-12-

0

QER 25-12-

98.5

QER 25-12-

97

Technical informationRADIAL INFEED FLANK INFEED MODIFIED FLANK INFEED ALTERNATING FLANK INFEED

This is the most common method of in-feed on short chipping materials. On long chipping materials it is difficult to break or control the chip as it shears from the flanks of the thread. The high heat generated from this method of in-feed on the tool nose radius causes premature tool failure.

Angular in-feed programmed at the same angle as the thread flank. Although the heat generated from this method is greatly reduced, the rear flank of the insert removes very little material, which can cause work hardening in some materials, and unsatisfactory surface finish on the rear flank of the thread.

Angular in-feed modified to generate additional work by the trailing insert edge and still maintain a smooth chip flow with reduced heat at the tool nose. Highly recommended for most types of material, however, the in-feed angle should be reduced on more abrasive materials to prevent work hardening. Recommended range 2.55

An excellent method for optimizing tool life. Many CNC machines offer these canned cycle subroutines and its use is highly recommended for most materials. The one disadvantage is loss of chip control in certain applications.

RIGHT-HAND THREAD COUNTER-CLOCKWISE ROTATIONQNR

LEFT-HAND THREAD CLOCKWISE ROTATIONQER--98.5 QEL

QER QEL--98.5 QNL

RIGHT-HAND THREAD CLOCKWISE ROTATIONQER QEL--98.5

LEFT-HAND THREAD COUNTER-CLOCKWISE ROTATIONQNR--98.5

QNL--98.5

QEL QER--98.5

9

Technical informationCUTTING DATAThe table gives recommended cutting speeds in feet/min and m/min for different materials and carbide grades. Material Low-carbon steel 650N/mm2 Carbon steel 650-850N/mm2 230-295 230-295 -1300 70-90 70-90 -400 Alloyed tool steel and heat-resistant steel Stainless steel Cast iron HB 180-250 Non-ferrous materials T10 / K20 T10C / K20C T10R / K20R C20

feet/min m/min feet/min m/min feet/min m/min feet/min m/min 590-720 180-220 690-820 210-250 590-1300 180-400 430-620 130-190 490-690 150-210 490-1150 150-350 400-530 120-160 460-590 140-180 490-1150 150-250 330-560 90-170 360-650 110-200 490-1150 150-250 420-560 130-170 -1900 -600

NUMBER OF PASSESThe table gives only general recommendations. Many times fewer passes can be used, depending on material and setup. Pitch mm Pitch TPI Nr. of passes 0.5 48 4-6 0.75 32 4-7 1.0 24 4-8 1.25 20 5-9 1.5 16 6-10 1.75 14 7-12 2.0 12 7-12 2.5 10 3.0 8 3.5 7 4.0 6 4.5 5.5 5.0 5 5.5 4.5 6.0 4

8-14 10-16 11-18 11-18 11-19 12-20 12-20 12-20

The above recommendations are for full profile UN, ISO and Withworth external forms. ForTrapezoidal, ACME, NPT and internal profiles please contact your local QuadThread distributor.

CARBIDE GRADES/COATINGSOur threading inserts are available in carbide grades T10 and K20. These two grades have an optimum combination of toughness and wear resistance, particulary for threading operations. T10 is a micrograin grade that has excellent cutting edge sharpness, also on the smallest profiles.

Insert size mm

CoatingsBoth of the basic grades are available with two different coatings. The most universal coating is designated C and is an ordinary TiN coating that performs very well on most materials. The R coating is TiAlN based and has been specially developed for threading operations. Excellent results have been achieved, particularly in stainless steels and other long chip materials. This is usually the universal problem solver.

Substrate

Simple designationsAs shown in the figure, the designations to the left describe the basic grade and the coating type.

Avoid edge build-upEdge build-up generally causes accelerated wear of the cutting edge. Edge build-up is usually due to incorrect temperature at the cutting area, which is known as the edge build-up area. The solution may be either to raise or lower the temperature. The coating prevents welding of the chip to the insert and reduces friction, lowering the temperature. If this fails to solve the problem, the cutting speed can be reset to an area outside the edge build-up area. Fewer passes may also be a solution, since this affects the temperature.

Coating

Coated grades

10

How to produce a threadDRAWING24 18 Op. 3

THREADING OPERATIONS

M42x2

G 3/4

G 3/4

48

11 17 50

18 22

Op. 2

Op. 1

1. CHOICE OF THREADING METHOD In this example the machine is rotating in a counter-clockwise direction with tools moving from right to left. This method will produce a right hand thread. 2. CHOICE OF CARBIDE GRADE The most suitable grade for stainless steel is T10C, because of its resistance to loose edge build-up. As this is an excellent all-round grade it will reduce your stock requirements. 3. CHOICE OF INSERT Operation 1 See page 14. Choose 12E 2.0ISO T10C Operation 2 See page 17. Choose 12X 14W T10C Operation 3 See page 30. Choose 10N 14W T10R 4. CHOICE OF HELIX ANGLE See the diagram on page 8. All threads lie within the field for helix angle 1.5. Op. 1 Cassette with helix angle1.5 should be used. Op. 2 NOTE! Here a left-hand toolholder is used to make a right-hand thread. A cassette with negative helix angle must be used, i.e. 98.5. Op. 3 Toolholder with helix angle 1.5 should be used. 5. CHOICE OF TOOLHOLDER AND CASSETTE Op. 1 See page 23. The toolblock dimension is 1. Choose cassette type toolholder QER 100 6-C25. For cassette see page 24. Holder shank is 1, insert is 12E and helix angle 1.5. Choose cassette QER 25-12. Op. 2 See page 36. A left-hand blade cassette is chosen with negative helix to make a right-hand thread. A block for standard cut-off blade 32mm is available. Use QEL 3206D-12-98.5 Op. 3 See page 39 A right-hand tool holder with a small diameter and helix angle 1.5 is chosen. Use QNR 0375 4-10

6. CHOICE OF INFEED METHOD See page 9. The material is long-chipping, and risk for cold hardening exists, so choice of correct infeed method is important. The machine is equipped with a G-function for alternating flank infeed, which should therefore be chosen. 7. CHOICE OF NUMBER OF PASSES See the table on page 10. For the external threads use 7 passes and for the internal 10 passes, since the stability is lower. When programming the thread depth, see the respective page for the thread form being used. 8. CHOICE OF CUTTING DATA The table on page 10 shows that the carbide grade T10C can be run between 90170 m/min in stainless steel. Vc = n x x D 1000 Vc = surface speed in m/min n = spindle speed in rpm

Op. 1 The lathe specifications show that nmax = 2200 rpm with pitch 2.0 and braking distance 2.5 mm. xx Vmax = 2200 1000 42 = 290 m/min Choose 170 m/min

Op. 2 The lathe specifications show that nmax = 950 rpm with pitch 14 TPI and starting distance 4.5 mm. Choose 70 m/min Vmax = 950 x x 24.2 = 72 m/min 1000 The low surface speed can give a problem with looseedge buildup. Op. 3 There is no problem with start or braking distance, so maximum spindle speed can be utilized. The lathe specifications give nmax= 4400 rpm with pitch 14TPI. Vmax= 4400 x x 24.2 =335 m/min Choose 180 m/min. 1000

11

Code keysTHREADING INSERTS

12Insert size 12 20 10 (only Internal) 11 (only Internal)

XExternal or Internal E=External N=Internal X=neutral Hand Blank=neutral R=right L=left

11Pitch mm TPI Partial profile AA A AG G, GN N, NV V

WProfile ISO UN W TR RD et al. Partial profile 60 55

T10CTeeth Blank=1 tooth 2M=2 teeth Grade T10 T10C T10R K20 K20C K20R C20 CBN T10

TOOLHOLDERS

QQuadThread threading system

EExternal or Internal E=External N=Internal

RHand R=right L=left

100 6Height and Width or Diameter 0375=.375 050=.50 0625=.625 075=.75 100=1.00 125=1.25 150=1.50 Length 3=3.0 4=4.0 45=4.5 5=5.0 6=6.0 7=7.0 8=8.0 10=10.0 12=12.0

25 25 MHeight or round 00=round 10=10 mm 12=12 mm 16=16 mm 20=20 mm 25=25 mm 32=32 mm 40=40 mm Width or diameter 10=10 mm 12=12 mm 16=16 mm 20=20 mm 25=25 mm 32=32 mm 40=40 mm 50=50 mm 63=63 mm Length F=80 mm H=100 mm J=110 mm K=125 mm M=150 mm P=170 mm R=200 mm S=250 mm T=300 mm Q=180 mm

C20 C25 12 20 10 11

C25Cassette or insert size(only External) (only External)

(only Internal) (only Internal) (only Internal) (only Internal)

Helix angle 4.5 = +4.5 3 = +3 1.5 = +1.5 0.7 = +0.7 0 = 0 98.5 = -1.5 97 = -3Blank = to be used with cassettes only

C50 C63

CASSETTES

QQuadThread threading system

E

RHand R=right L=left

25

-

12Insert size 12 20

Helix angle 4.5 = +4.5 3 = +3 Blank=1.5 0.7 = +0.7o 0 = 0 98.5 = -1.5 97 = -3

External or internal E=External N=Internal

Cassette size 20 25 50 (only Internal) 63 (only Internal)

12

QuadThread External insertsPartial Profile 60External and Internal threading Pitch mm TPI 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 1.75-3.0 14-8 3.5-5.0 7-5 5.5-6.0 4.5-4 Catalog number 12X A60 12X AG60 12X AG60-SP 12X G60 20X N60 20X V60 Dimensions Uncoated PriceCoated Cermet l s t R T10 K20 group T10C K20C C20 .472 .094 .047 .003 1 * .472 .142 .071 .003 2 * .472 .142 .071 .005 2 * .472 .142 .071 .008 2 * .787 .181 .091 .016 * 3 .787 .268 .134 .031 * 4 Coated T10R K20R * * * * * * Pricegroup 11 12 12 12 13 14

Partial Profile 60External and Internal threading Pitch Catalog Dimensions mm TPI number l s t R 0.35-1.0 72-24 12ER AA60 .472 .094 .024 .002 Uncoated K20 * Pricegroup 1 Coated K20C K20R * Pricegroup 11

Partial Profile 55External and Internal threading Pitch mm TPI 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 3.5-5.0 7-5 5.5-6.0 4.5-4 Catalog number 12X A55 12X AG55 12X G55 20X N55 20X V55 Dimensions l s t R .472 .094 .047 .003 .472 .142 .071 .003 .472 .142 .071 .008 .787 .181 .091 .019 .787 .268 .134 .029 Uncoated T10 * * * * * Pricegroup 1 2 2 3 4 Coated T10C T10R K20C K20R * * * * * * Pricegroup 11 12 12 13 14

Partial Profile 55External and Internal threading Pitch mm TPI 0.35-1.0 72-24 Catalog Dimensions number l s t R 12ER AA55 .472 .094 .024 .002 Uncoated K20 * Pricegroup 1 Coated K20C K20R * * Pricegroup 11 13

QuadThread External insertsRmin0.125P Rmax0.144P

ISO Metric (M)0.125P

External threading Catalog number 12E 0.5ISO 12E 0.75ISO 12E 1.0ISO 12E 1.25ISO 12E 1.5ISO 12E 1.75ISO 12E 2.0ISO 12E 2.5ISO 12E 3.0ISO 20E 3.5ISO 20E 4.0ISO 20E 4.5ISO 20E 5.0ISO 20E 5.5ISO 20E 6.0ISO Dimensions Uncoated PriceCoated Cermet l s t h T10 K20 group T10C K20C C20 .472 .094 .047 .012 * 1 .472 .094 .047 .019 * 1 .472 .094 .047 .025 * 1 * .472 .094 .047 .031 * 1 .472 .094 .047 .037 * 1 * .472 .094 .047 .043 * 1 .472 .094 .047 .049 * 1 * .472 .142 .071 .061 * 2 .472 .142 .071 .074 * 2 .787 .181 .091 .086 * 3 .787 .181 .091 .099 * 3 .787 .268 .134 .111 * 4 .787 .268 .134 .123 * 4 .787 .268 .134 .135 * 4 .787 .268 .134 .148 * 4 Coated T10R K20R Pricegroup 11 11 11 11 11 11 11 12 12 13 13 14 14 14 14

Pitch mm 0.5 0.75 1.0 1.25 1.5 1.75 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0Rmin0.125P Rmax0.144P

ISO Metric (M)External threading with small pitches Catalog number 12ER 0.35ISO 12ER 0.4ISO 12ER 0.45ISO 12ER 0.5ISO 12ER 0.6ISO 12ER 0.7ISO 12ER 0.75ISO 12ER 0.8ISO 12ER 1.0ISO Dimensions l s t .472 .094 .016 .472 .094 .016 .472 .094 .016 .472 .094 .016 .472 .094 .024 .472 .094 .024 .472 .094 .024 .472 .094 .024 .472 .094 .024 Uncoated K20 * * * * * * * * * Pricegroup 1 1 1 1 1 1 1 1 1 Coated K20C K20R * * * * * * * * * * * * * * Pricegroup 11 11 11 11 11 11 11 11 11 h .009 .010 .011 .012 .015 .017 .019 .020 .025

0.125P

Pitch mm 0.35 0.4 0.45 0.5 0.6 0.7 0.75 0.8 1.0Rmin0.125P Rmax0.144P

ISO Metric (M)External threading multitooth Dimensions No. l s t h teeth .472 .094 .067 .025 2 .472 .142 .100 .037 2 .787 .181 .130 .049 2 .787 .268 .183 .061 2 .787 .268 .193 .074 2 .787 .268 .203 .086 2 .787 .268 .213 .099 2 Radial infeed 1 2 3 0.24 0.21 0.18 0.43 0.30 0.21 0.57 0.40 0.28 0.59 0.42 0.30 0.61 0.52 0.42 0.70 0.65 0.52 0.70 0.59 0.49 per pass 4 5 Coated PriceT10C T10R K20C K20R group * * 51 * * 52 * * 53 * * 54 * * 54 * * 54 0.33 * * 54

0.125P

Pitch mm 1.0 1.5 2.0 2.5 3.0 3.5 4.0 14

Catalog number 12ER 1.0ISO2M 12ER 1.5ISO2M 20ER 2.0ISO2M 20ER 2.5ISO2M 20ER 3.0ISO2M 20ER 3.5ISO2M 20ER 4.0ISO2M

0.25 0.32 0.32 0.40


MJ0.125P

External threading Catalog number 12E 1.5MJ 12E 2.0MJ Dimensions s t .094 .047 .094 .047 Coated T10C T10R * * * * Pricegroup 31 31

Pitch mm 1.5 2.0

l .472 .472

h .035 .047


MJ0.125P

External threading Catalog number 12ER 1.0MJ Dimensions s t .094 .024 Coated K20C K20R * * Pricegroup 31

Pitch mm 1.0

l .472

h .024


ISO Unified (UN)External threading0.125P

Pitch TPI 32 28 24 20 18 16 14 13 12 11 10 9 8 7 6 5 4.5 4

Catalog number 12E 32UN 12E 28UN 12E 24UN 12E 20UN 12E 18UN 12E 16UN 12E 14UN 12E 13UN 12E 12UN 12E 11UN 12E 10UN 12E 9UN 12E 8UN 20E 7UN 20E 6UN 20E 5UN 20E 4.5UN 20E 4UN

Dimensions Uncoated PriceCoated Cermet l s t h T10 K20 group T10C K20C C20 .472 .094 .047 .020 * 1 * .472 .094 .047 .022 * 1 * .472 .094 .047 .026 * 1 * .472 .094 .047 .031 * 1 * .472 .094 .047 .035 * 1 * .472 .094 .047 .039 * 1 * .472 .094 .047 .045 * 1 * * .472 .094 .047 .048 * 1 * .472 .094 .047 .052 * 1 * .472 .142 .071 .057 * 2 * * .472 .142 .071 .063 * 2 * .472 .142 .071 .070 * 2 * .472 .142 .071 .078 * 2 * .787 .181 .091 .089 * 3 * .787 .181 .091 .104 * 3 * .787 .268 .134 .125 * 4 * .787 .268 .134 .139 * 4 * .787 .268 .134 .157 * 4 *

Coated T10R K20R * * * * * * * * * * * * * * * * * *

Pricegroup 11 11 11 11 11 11 11 11 11 12 12 12 12 13 13 14 14 14 15


ISO Unified (UN)0.125P

External threading with small pitches Catalog number 12ER 72UN 12ER 64UN 12ER 56UN 12ER 48UN 12ER 44UN 12ER 40UN 12ER 36UN 12ER 32UN 12ER 28UN 12ER 24UN Dimensions s t .094 .016 .094 .016 .094 .016 .094 .024 .094 .024 .094 .024 .094 .024 .094 .024 .094 .024 .094 .024 Coated h .009 .010 .011 .013 .014 .016 .017 .020 .022 .026 K20C * * * * * * * * * * K20R * * * * * * * * * * Pricegroup 11 11 11 11 11 11 11 11 11 11

Pitch TPI 72 64 56 48 44 40 36 32 28 24

l .472 .472 .472 .472 .472 .472 .472 .472 .472 .472


ISO Unified (UN)0.125P

External threading multitooth

Pitch Catalog Dimensions No. Radial infeed per pass Coated PriceTPI number l s t h teeth 1 2 3 4 T10C T10R K20C K20R group 16 12ER 16UN2M .472 .142 .102 .039 2 .0178 .0126 .0089 * * 52 12 20ER 12UN2M .787 .181 .132 .052 2 .0236 .0170 .0118 * * 53 8 20ER 8UN2M .787 .268 .196 .078 2 .0256 .0217 .0178 .0134 * * 54


UNJ0.125P

External threading Catalog number 12E 28UNJ 12E 24UNJ 12E 20UNJ 12E 18UNJ 12E 16UNJ 12E 14UNJ 12E 12UNJ 12E 10UNJ 12E 8UNJ Dimensions s t .094 .047 .094 .047 .094 .047 .094 .047 .094 .047 .094 .047 .094 .047 .142 .071 .142 .071 Uncoated T10 * * * * * * * * * PriceCoated Pricegroup T10C T10R group 21 * * 31 21 * * 31 21 * * 31 21 * * 31 21 * * 31 21 * * 31 21 * * 31 22 * * 32 22 * * 32

Pitch TPI 28 24 20 18 16 14 12 10 8 16

l .472 .472 .472 .472 .472 .472 .472 .472 .472

h .021 .025 .030 .033 .037 .043 .050 .060 .075


UNJ0.125P

External threading with small pitches Catalog number 12ER 40UNJ 12ER 32UNJ 12ER 28UNJ 12ER 24UNJ Dimensions s t .094 .024 .094 .024 .094 .024 .094 .024 Coated K20C K20R * * * * * * * * Pricegroup 31 31 31 31

Pitch TPI 40 32 28 24

l .472 .472 .472 .472

h .011 .019 .021 .025

UN Round - QuadThread UN-profiles meet the requirement of tighter tolerances and rounded crests for UN round profiles.

R=0.137P

Whitworth (BSW, BSP)R=0.137P

External and Internal threading Catalog number 12X 28W 12X 24W 12X 22W 12X 20W 12X 19W 12X 18W 12X 16W 12X 14W 12X 12W 12X 11W 12X 10W 12X 9W 12X 8W 20X 7W 20X 6W 20X 5W 20X 4.5W 20X 4W Dimensions Uncoated PriceCoated Cermet l s t h T10 K20 group T10C K20C C20 .472 .094 .047 .023 * 1 * .472 .094 .047 .027 * 1 * .472 .094 .047 .030 * 1 * .472 .094 .047 .032 * 1 * .472 .094 .047 .034 * 1 * .472 .094 .047 .036 * 1 * .472 .094 .047 .041 * 1 * .472 .094 .047 .046 * 1 * .472 .094 .047 .054 * 1 * .472 .142 .071 .059 * 2 * .472 .142 .071 .065 * 2 * .472 .142 .071 .072 * 2 * .472 .142 .071 .081 * 2 * .787 .181 .091 .093 * 3 * .787 .181 .091 .108 * 3 * .787 .181 .091 .130 * 3 * .787 .268 .134 .144 * 4 * .787 .268 .134 .162 * 4 * Coated T10R K20R * * * * * * * * * * * * * * * Pricegroup 11 11 11 11 11 11 11 11 11 12 12 12 12 13 13 13 14 14

Pitch TPI 28 24 22 20 19 18 16 14 12 11 10 9 8 7 6 5 4.5 4

R=0.137P


External threading with small pitches Catalog number 12ER 32W 12ER 28W 12ER 26W 12ER 24W Dimensions s t .094 .024 .094 .024 .094 .024 .094 .024 Coated K20C K20R * * * * * * * * Pricegroup 11 11 11 11 17

Pitch TPI 32 28 26 24

l .472 .472 .472 .472

h .020 .023 .025 .027

QuadThread External insertsR=0.137P


External threading multitooth Dimensions No. Radial infeed per pass Coated Pricel s t h teeth 1 2 3 4 T10C T10R K20C K20R group .472 .142 .107 .046 2 .0217 .0150 .0098 * * 52 .787 .181 .136 .059 2 .0217 .0150 .0126 .0098 * * 53

Pitch TPI 14 11

Catalog number 12ER 14W2M 20ER 11W2M

R=0.137P

27.527.5 R=0.137P l47

BSPTExternal and Internal threading Catalog number 12X 14BSPT 12X 11BSPT Dimensions s t .142 .071 .142 .071 Coated h .048 .061 T10C * * T10R * * Pricegroup 32 32 l .472 .472

Pitch TPI 14 11

R=0.137P

BSPTR=0.137P

External threading multitooth

Pitch Catalog Dimensions No. Radial infeed per pass Coated PriceTPI number l s t h teeth 1 2 3 4 T10C T10R K20C K20R group 14 12ER 14BSPT2M .472 .142 .107 .048 2 .0220 .0154 .0102 * * 52 11 20ER 11BSPT2M .787 .181 .136 .061 2 .0220 .0154 .0130 .0102 * * 53

R=0.107P

Pansarrohrgewinde (PG)External and Internal threading Catalog number 12X 20PG 12X 18PG 12X 16PG Dimensions s t .094 .047 .094 .047 .094 .047 Coated T10C T10R * * * * * * Pricegroup 31 31 31 l .472 .472 .472 h .024 .026 .030

R=0.107P

Pitch TPI 20 18 16 18

QuadThread External insertsTrapezoidal DIN 103External and Internal threading Pitch mm 1.5 2.0 3.0 4.0 5.0 6.0 Catalog number 12X 1.5TR 12X 2.0TR 12X 3.0TR 20X 4.0TR 20X 5.0TR 20X 6.0TR Dimensions l s t h .472 .094 .047 .035 .472 .094 .047 .049 .472 .142 .071 .069 .787 .181 .091 .089 .787 .268 .134 .108 .787 .268 .134 .138 Uncoated T10 K20 * * * * * * Pricegroup 21 21 22 23 24 24 Coated PriceT10C T10R K20C K20R group * * 31 * * 31 * * 32 * * 33 * * 34 * * 34

R=0.238P

Round DIN 405External threading Catalog number 12E 10RD 12E 8RD 20E 6RD 20E 4RD Dimensions l s t h .472 .142 .071 .050 .472 .142 .071 .063 .787 .181 .091 .083 .787 .268 .134 .125 Uncoated T10 K20 * * * * Pricegroup 22 22 23 24 Coated PriceT10C T10R K20C K20R group * * 32 * * 32 * * 33 * * 34

R=0.238P

Pitch TPI 10 8 6 4

ModulExternal threading Pitch mm 1.57 2.36 3.14 3.93 4.71 6.28 Catalog number 12E 0.5MOD 12E 0.75MOD 20E 1.0MOD 20E 1.25MOD 20E 1.5MOD 20E 2.0MOD Dimensions s t .094 .047 .142 .071 .181 .091 .181 .091 .268 .134 .268 .134 Coated T10C T10R K20C K20R * * * * * * * * * * * * Pricegroup 31 32 33 33 34 34 l .472 .472 .787 .787 .787 .787 h .044 .067 .089 .111 .133 .177

19

QuadThread External insertsACMEExternal and Internal threading Pitch TPI 16 14 12 10 8 6 5 4 Catalog number 12X 16ACME 12X 14ACME 12X 12ACME 12X 10ACME 12X 8ACME 20X 6ACME 20X 5ACME 20X 4ACME Dimensions l s t h .472 .094.047.040 .472 .094.047.044 .472 .094.047.052 .472 .142.071.065 .472 .142.071.079 .787 .181.091.100 .787 .268.134 .118 .787 .268.134 .143 Uncoated T10 K20 * * * * * * * * Pricegroup 21 21 21 22 22 23 24 24 Coated PriceT10C T10R K20C K20R group * * 31 * * 31 * * 31 * * 32 * * 32 * * 33 * * 34 * * 34

STUB ACMEExternal and Internal threading Pitch TPI 16 14 12 10 8 6 5 4 Catalog number 12X 16STACME 12X 14STACME 12X 12STACME 12X 10STACME 12X 8STACME 20X 6STACME 20X 5STACME 20X 4STACME Dimensions l s t h .472 .094.047.028 .472 .094.047.030 .472 .094.047.035 .472 .142.071.045 .472 .142.071.054 .787 .181.091.067 .787 .268.134.078 .787 .268.134.093 Uncoated T10 K20 * * * * * * * * PriceCoated Pricegroup T10C T10R K20C K20R group 21 * * 31 21 * * 31 21 * * 31 22 * * 32 22 * * 32 23 * * 33 24 * * 34 24 * * 34

R=0.125P

NPSMExternal threadingR=0.125P

Pitch TPI 27 18 14 11.5 8

Catalog number 12E 27NPSM 12E 18NPSM 12E 14NPSM 12E 11.5NPSM 20E 8NPSM

l .472 .472 .472 .472 .787

Dimensions s t .094 .047 .094 .047 .094 .047 .142 .071 .181 .091

h .026 .038 .049 .060 .086

Coated T10C T10R K20C K20R * * * * * * * * * *

Pricegroup 31 31 31 32 33

20

QuadThread External inserts30 30 l47

NPTExternal and Internal threading Catalog number 12X 27NPT 12X 18NPT 12X 14NPT 12X 11.5NPT 20X 8NPT Dimensions Uncoated PriceCoated Cermet l s t h T10 K20 group T10C K20C C20 .472 .094 .047 .028 * 21 * .472 .094 .047 .041 * 21 * .472 .094 .047 .054 * 21 * * .472 .142 .071 .066 * 22 * * .787 .181 .091 .096 * 23 * Coated T10R K20R * * * * * Pricegroup 31 31 31 32 33

Pitch TPI 27 18 14 11.5 8

3030 l47

NPTExternal threading with small pitches Catalog Dimensions number l s t h 12ER 27NPT .472 .094 .024 .028 Uncoated K20 * Pricegroup 21 Coated K20C K20R * * Pricegroup 31

Pitch TPI 27

30 30 l47

NPTExternal threading multitooth Catalog Dimensions No. Radial infeed per pass number l s t h teeth 1 2 3 4 20ER 11.5NPT2M .787 .181 .134 .066 23 .0236 .0177 .0150 .0098 20ER 8NPT2M .787 .268 .196 .096 24 .0295 .0276 .0276 .0110 Coated K20C K20R * * * * Pricegroup 53 54

Pitch TPI 11.5 8

30 0.125P

30 l47

NPTF DrysealExternal and Internal threading Catalog number 12X 27NPTF 12X 18NPTF 12X 14NPTF 12X 11.5NPTF 20X 8NPTF Dimensions l s t h .472 .094.047.026 .472 .094.047.040 .472 .094.047.054 .472 .142.071.065 .787 .181.091.095 Uncoated T10 K20 * * * * * PriceCoated Pricegroup T10C T10R K20C K20R group 21 * * 31 21 * * 31 21 * * 31 22 * * 32 23 * * 33 21

Pitch TPI 27 18 14 11.5 8

QuadThread External inserts3030 l47 0.125P

NPTF DrysealExternal threading with small pitches Catalog Dimensions number l s t h 12ER 27NPTF .472 .094 .024. 026 Uncoated K20 * Pricegroup 21 Coated K20C K20R * * Pricegroup 31

Pitch TPI 27

Warning! Always determine if NPT or NPTF profile should be used. Be sure you use the right one. NPT, Line Pipe NPTF Dryseal

NPT and Line Pipe have clearance on the top and bottom of the thread. QuadThread NPT profiles also fit the tolerances for Line Pipe profiles.

NPTF Dryseal gives a tight fit. This is accomplished when the pipe components are fitted together, as the top of the thread is deformed by the corressponding thread root.

30 30 l47

API RDExternal and Internal threading Catalog Dimensions number l s t h 12X 10APIRD .472 .142 .071 .057 20X 8APIRD .787 .181 .091 .073 Uncoated T10 K20 * * Pricegroup 22 23 Coated PriceT10C T10R K20C K20R group * * 32 * * 33

Pitch TPI 10 8

R

30 30 TPF

APIExternal threading. Cassette QER25-20API must be used. Catalog number 20ER 5API404 20ER 4API384 20ER 4API386 20ER 4API504 20ER 4API506 Dimensions h R .1178 .020 .1214 .038 .1218 .038 .1473 .025 .1478 .025 API Coated Code K20C K20R V-0.040 * * V-0.038R * * V-0.038R * * V-0.050 * * V-0.050 * * Pricegroup 34 34 34 34 34 l .787 .787 .787 .787 .787 s .268 .268 .268 .268 .268 t .134 .134 .134 .134 .134 Fc .040 .065 .065 .050 .050 TPF 3 3 2 3 2

Fc

Pitch TPI 5 4 4 4 4 22

QuadThread External toolholdersQER shown

ToolholdersInsert E .77 .77 .77 .77 .77 .77 .77 .77 12 12 12 12 12 12 12 12 3 Stock standard (k) 1.5 0 98.5 97 Pricegroup 226 226 226 226 226 226 226 226

Catalog number QER 0375 3-12 QER 0375 6-12 QER 050 3-12 QER 050 6-12 QEL 0375 3-12 QEL 0375 6-12 QEL 050 3-12 QEL 050 6-12

H/B .375 .375 .50 .50 .375 .375 .50 .50

Dimensions l f 3.0 .375 6.0 .375 3.0 .50 6.0 .50 3.0 .375 6.0 .375 3.0 .50 6.0 .50

Clamping toolholdersCatalog number QER 202003K-12 QER 202004K-12 Dimensions (mm) H/B l s E 20 125 2.4 27 20 125 3.6 27 Insert 12 12 Stock standard (k) 1.5 0 98.5 Pricegroup 227 227

QER shown

Cassette type toolholdersE .89 .89 1.16 1.16 1.16 .89 .89 1.16 1.16 1.16 Cassettes Insert 12... Insert 20... QER 20-12 QER 20-12 QER 25-12 QER 25-20 QER 25-12 QER 25-20 QER 25-12 QER 25-20 QEL 20-12 QEL 20-12 QEL 25-12 QEL 25-20 QEL 25-12 QEL 25-20 QEL 25-12 QEL 25-20 Stock standard (k) Pricegroup 224 224 225 228 231 224 224 225 228 231

Catalog number QER 0625 4-C20 QER 075 5-C20 QER 100 6-C25 QER 125 7-C25 QER 150 7-C25 QEL 0625 4-C20 QEL 075 5-C20 QEL 100 6-C25 QEL 125 7-C25 QEL 150 7-C25

H/B .625 .75 1.00 1.25 1.50 .625 .75 1.00 1.25 1.50

Dimensions l f 4.0 .75 5.0 1.00 6.0 1.25 7.0 1.50 7.0 1.75 4.0 .75 5.0 1.00 6.0 1.25 7.0 1.50 7.0 1.75

Toolholders delivered without cassette, to be ordered separately. 23

QuadThread External toolholdersStandard cassettesCatalog number QER 20-12 QER 25-12 QER 25-20 QEL 20-12 QEL 25-12 QEL 25-20 Insert 12 12 20 12 12 20 4.5 * * * * * * 3 * * * Stock standard (k) 1.5 0 98.5 * * * * * * * * * 97 * * * * * * Pricegroup 219 219 219 219 219 219

Extended cassettesCatalog number QER 20-12FL QER 25-12FL QER 25-20FL QEL 20-12FL QEL 25-12FL QEL 25-20FL Insert 12 12 20 12 12 20 l (Length extended) .236 .394 .394 .236 .394 .394 1.5 * * * Stock standard (k) 0 98.5 * * * * * * * * * * * * Pricegroup 220 220 220 220 220 220

API cassettesCatalog number QER 25-20API QEL 25-20API Insert 20E 20E 1.5 * * Stock standard (k) 0 * * 98.5 Pricegroup 219 219

This cassette is used only for certain API inserts.

f-DimensionFor some inserts the f-dimension is displaced according to the f2-dimension in the table. Dimensions s .094 .142 .181 .268 L .472 .472 .787 .787 f2 0 .047 0 .087

Helix angle 1.5 is standard and does not need to be shown when ordering cassettes, for instance, QER 25-12. All other helix angles should be shown after the cassette catalog number, for instance, QER 25-12-98.5 24

QuadThread External toolholdersSmall axialtype toolholdersInsert E .39 .39 .39 .39 12 12 12 12 3 * * * * Stock standard (k) 1.5 0 98.5 * * * * * * * * * * * * 97 * * * * Pricegroup 226 226 226 226

QER shown

Catalog number QER 0375 3F-12 QER 050 3F-12 QEL 0375 3F-12 QEL 050 3F-12

Dimensions H/B l f .375 3.0 .63 .50 3.0 .63 .375 3.0 .63 .50 3.0 .63

QER shown

Cassette type axial toolholdersE .32 .32 .40 .32 .32 .40 Cassettes Insert 12... Insert 20... QER 20-12 QER 20-12 QER 25-12 QER 25-20 QEL 20-12 QEL 20-12 QEL 25-12 QEL 25-20 Stock standard (k) * * * * * * Pricegroup 224 224 225 224 224 225

Catalog number QER 0625 4F-C20 QER 075 5F-C20 QER 100 6F-C25 QEL 0625 4F-C20 QEL 075 5F-C20 QEL 100 6F-C25

H/B .625 .75 1.00 .625 .75 1.00

Dimensions l f 4.0 .95 5.0 .95 6.0 1.25 4.0 .95 5.0 .95 6.0 1.25

Toolholders delivered without cassette, to be ordered separately.

l-DimensionFor some inserts the l-dimension is displaced according to the l2-dimension in the table. l2

L .472 .472 .787 .787

Dimensions s .094 .142 .181 .268

l2 0 .047 0 .087

25

QuadThread External toolholdersBlade cassette toolholdersInsert 12 12 12 12 Stock standard (k) 1.5 0 98.5 * * * * Pricegroup 227 227 227 227

QER shown QEL shown

Catalog number QER 2606D-12 QER 3206D-12 QEL 2606D-12 QEL 3206D-12

H 1.02 1.26 1.02 1.26

Dimensions l B 3.94 .24 4.72 .24 3.94 .24 4.72 .24

Drophead toolholdersCatalog number QER 075 5C-C20 QER 100 6C-C25 QER 125 7C-C25 QEL 075 5C-C20 QEL 100 6C-C25 QEL 125 7C-C25 H/B .75 1.00 1.25 .75 1.00 1.25 Dimensions l f 5.0 1.00 6.0 1.25 7.0 1.50 5.0 1.00 6.0 1.25 7.0 1.50 E 1.02 1.30 1.30 1.02 1.30 1.30 Cassettes Insert 12... Insert 20... QER 20-12 QER 25-12 QER 25-20 QER 25-12 QER 25-20 QEL 20-12 QEL 25-12 QEL 25-20 QEL 25-12 QEL 25-20 Stock standard (k) * * * Pricegroup 229 230 232 229 230 232

Toolholders delivered without cassette, to be ordered separately.

ScrewsCatalog number STS T9xM3 STS T9xM3 STS T9xM3 STS T15xM5 Used for Insert 10 Insert 11 Insert 12 Insert 20 Pricegroup 221 221 221 221

KeysCatalog number Torx T9 Torx T15 26 Used for STS T9xM3 STS T15xM5 Pricegroup 222 222

QuadThread Internal insertsDifferent insert sizes for different diameters

QuadThread 10For diameters .55 and above. This insert has only two edges. Otherwise it has the same stability and advantages as the QuadThread External.

QuadThread 11For diameters 1.18 and sbove. The inserts is tilted 20 to allow for four edges.

QuadThread 12 and 20An enduring part of the QuadThread threading system. The common insert profiles for internal threads fit into this holder. Diameters of 2.20 or above may be machined.

Partial Profile 60Internal threading Pitch mm TPI 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 Catalog number 10N A60 10N AG60 10N G60 Dimensions l s t R .394 .094 .047 .002 .394 .142 .071 .003 .394 .142 .071 .005 Uncoated T10 K20 * * * Pricegroup 5 6 6 Coated T10C T10R K20C PriceK20R group 15 16 16

Partial Profile 60Internal threading Pitch mm TPI 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 1.75-3.0 14-8 3.5-5.0 7-5 5.5-6.0 4.5-4 Catalog number 11N A60 11N AG60 11N G60 12X A60 12X AG60 12X AG60-SP 12X G60 20X N60 20X V60 Dimensions l s t R .472 .094 .047 .002 .472 .142 .071 .003 .472 .142 .071 .005 .472 .094 .047 .003 .472 .142 .071 .003 .472 .142 .071 .005 .472 .142 .071 .008 .787 .181 .091 .016 .787 .268 .134 .031 Uncoated T10 K20 * * * * * Pricegroup 7 8 8 1 2 2 2 3 4 Coated T10C T10R K20C * * * * * * * PriceK20R group 17 18 18 11 12 12 12 * 13 * 14

Partial Profile 55Internal threading Pitch mm TPI 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 Catalog number 10N A55 10N AG55 10N G55 Dimensions l s t R .394 .094 .047 .003 .394 .142 .071 .003 .394 .142 .071 .008 Uncoated T10 K20 * * * Pricegroup 5 6 6 Coated T10C T10R K20C PriceK20R group 15 16 16 27

QuadThread Internal insertsPartial Profile 55Internal threading Pitch mm TPI 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 0.5-2.0 48-12 0.5-3.0 48-8 1.75-3.0 14-8 3.5-5.0 7-5 5.5-6.0 4.5-4 Catalog number 11N A55 11N AG 55 11N G55 12X A55 12X AG55 12X G55 20X N55 20X V55 Dimensions l s t R .472 .094 .047 .003 .472 .142 .071 .003 .472 .142 .071 .008 .472 .094 .047 .003 .472 .142 .071 .003 .472 .142 .071 .008 .787 .181 .091 .019 .787 .268 .134 .029 Uncoated T10 K20 * * * * * * * * Pricegroup 7 8 8 1 2 2 3 4 Coated T10C T10R K20C * * * * * * PriceK20R group 17 18 18 11 12 12 * 13 * 14

ISO Metric (M)0.25P

Internal threading Catalog number 10N 0.5ISO 10N 0.75ISO 10N 1.0ISO 10N 1.25ISO 10N 1.5ISO 10N 1.75ISO 10N 2.0ISO 10N 2.5ISO 10N 3.0ISO Dimensions l s t h .394 .094 .047 .011 .394 .094 .047 .017 .394 .094 .047 .023 .394 .094 .047 .029 .394 .094 .047 .035 .394 .094 .047 .040 .394 .094 .047 .046 .394 .142 .071 .057 .394 .142 .071 .069 Uncoated T10 K20 * * * * * * * * * Pricegroup 5 5 5 5 5 5 5 6 6 Coated T10C T10R K20C PriceK20R group 15 15 15 15 15 15 15 16 16

Pitch mm 0.5 0.75 1.0 1.25 1.5 1.75 2.0 2.5 3.0

ISO Metric (M)0.25P

Internal threading Catalog number 11N 1.0ISO 11N 1.5ISO 11N 2.0ISO 11N 2.5ISO 11N 3.0ISO 12N 1.5ISO 12N 2.0ISO 12N 3.0ISO 20N 4.0ISO 20N 5.0ISO 20N 6.0ISO Dimensions l s t h .472 .094 .047 .023 .472 .094 .047 .035 .472 .094 .047 .046 .472 .142 .071 .057 .472 .142 .071 .069 .472 .094 .047 .035 .472 .094 .047 .046 .472 .142 .071 .069 .787 .181 .091 .092 .787 .268 .134 .115 .787 .268 .134 .138 Uncoated T10 K20 * * * * * Pricegroup 7 7 7 8 8 1 1 2 3 4 4 Coated T10C T10R K20C PriceK20R group 17 17 17 18 18 11 11 12 13 14 14

Pitch mm 1.0 1.5 2.0 2.5 3.0 1.5 2.0 3.0 4.0 5.0 6.0 28

QuadThread Internal insertsISO Metric (M)0.25P

Internal threading multitooth Catalog Dimensions No. Radial infeed per pass Coated Pricenumber l s t h teeth 1 2 3 T10C T10R K20R group 12NR 1.5ISO2M .472 .142 .100 .035 2 .0161 .0110 .0075 * * 52 12NR 2.0ISO2M .472 .142 .100 .046 2 .0212 .0146 .0102 * * 52

Pitch mm 1.5 2.0

ISO Unified (UN)Internal threading0.25P

Pitch TPI 32 28 24 20 18 16 14 12 11 10 9 8

Catalog number 10N 32UN 10N 28UN 10N 24UN 10N 20UN 10N 18UN 10N 16UN 10N 14UN 10N 12UN 10N 11UN 10N 10UN 10N 9UN 10N 8UN

Dimensions l s t h .394 .094 .047 .018 .394 .094 .047 .020 .394 .094 .047 .024 .394 .094 .047 .029 .394 .094 .047 .033 .394 .094 .047 .037 .394 .094 .047 .042 .394 .094 .047 .049 .394 .142 .071 .053 .394 .142 .071 .059 .394 .142 .071 .065 .394 .142 .071 .073

Uncoated T10 K20 * * * * * * * * * * * *

Pricegroup 5 5 5 5 5 5 5 5 6 6 6 6

Coated T10C T10R K20C * * * * * * * * * * * *

PriceK20R group 15 15 15 15 15 15 15 15 16 16 16 16

29

QuadThread Internal insertsISO Unified (UN)0.25P

Internal threading Catalog number 11N 20UN 11N 18UN 11N 16UN 11N 14UN 11N 12UN 11N 10UN 11N 8UN 12N 18UN 12N 16UN 12N 14UN 12N 12UN 12N 10UN 12N 8UN 20N 6UN 20N 5UN 20N 4UN Dimensions l s t h .472 .094 .047 .029 .472 .094 .047 .033 .472 .094 .047 .037 .472 .094 .047 .042 .472 .094 .047 .049 .472 .142 .071 .059 .472 .142 .071 .073 .472 .094 .047 .033 .472 .094 .047 .037 .472 .094 .047 .042 .472 .094 .047 .049 .472 .142 .071 .059 .472 .142 .071 .073 .787 .181 .091 .098 .787 .268 .134 .117 .787 .268 .134 .146 Uncoated T10 K20 * * * * * * * * * * * * * * * * Pricegroup 7 7 7 7 7 8 8 1 1 1 1 2 2 3 4 4 Coated T10C T10R K20C * * * * * * * * * * * * * * * * * * * * * * PriceK20R group 17 17 17 17 17 18 18 11 11 11 11 12 12 * 13 * 14 * 14

Pitch TPI 20 18 16 14 12 10 8 18 16 14 12 10 8 6 5 4

R=0.137P


Internal threading with small pitches Catalog number 10N 20W 10N 19W 10N 14W 10N 12W 10N 11W 10N 10W 10N 9W 10N 8W Dimensions l s t h .394 .094 .047 .032 .394 .094 .047 .034 .394 .094 .047 .046 .394 .094 .047 .054 .394 .142 .071 .059 .394 .142 .071 .065 .394 .142 .071 .072 .394 .142 .071 .081 Uncoated T10 K20 * * * * * * * * Pricegroup 5 5 5 5 6 6 6 6 Coated T10C T10R K20C * * * * * PriceK20R group 15 15 15 15 16 16 16 16

Pitch TPI 20 19 14 12 11 10 9 8

30

QuadThread Internal insertsR=0.137P


External and Internal threading Catalog number 11N 19W 11N 14W 11N 12W 11N 11W 12X 28W 12X 24W 12X 22W 12X 20W 12X 19W 12X 18W 12X 16W 12X 14W 12X 12W 12X 11W 12X 10W 12X 9W 12X 8W 20X 7W 20X 6W 20X 5W 20X 4.5W 20X 4W Dimensions l s t h .472 .094 .047 .034 .472 .094 .047 .046 .472 .094 .047 .054 .472 .142 .071 .059 .472 .094 .047 .023 .472 .094 .047 .027 .472 .094 .047 .030 .472 .094 .047 .032 .472 .094 .047 .034 .472 .094 .047 .036 .472 .094 .047 .041 .472 .094 .047 .046 .472 .094 .047 .054 .472 .142 .071 .059 .472 .142 .071 .065 .472 .142 .071 .072 .472 .142 .071 .081 .787 .181 .091 .093 .787 .181 .091 .108 .787 .268 .134 .130 .787 .268 .134 144 .787 .268 .134 .162 Uncoated T10 K20 * * * * * * * * * * * * * * * * * * * * * Pricegroup 7 7 8 8 1 1 1 1 1 1 1 1 1 2 2 2 2 3 3 3 4 4 Coated T10C T10R K20C * * * * * * * * * * * * * * * * * * * PriceK20R group 17 17 18 18 11 11 11 11 11 11 11 11 11 12 12 12 12 13 13 13 14 14

Pitch TPI 19 14 12 11 28 24 22 20 19 18 16 14 12 11 10 9 8 7 6 5 4.5 4

R=0.137P


Internal threading multitooth Catalog number 20NR 11W2M Dimensions No. Radial infeed per pass l s t h teeth 1 2 3 4 .787 .181 .136 .059 2 .0217 .0150 .0126 .0098 Coated K20C K20R * * Pricegroup 53

Pitch TPI 11

R=0.137P

27.5 27.5 R=0.137P l47

BSPTExternal and Internal threading Catalog number 12X 14BSPT 12X 11BSPT Dimensions l s t h .472 .142 .071 .048 .472 .142 .071 .061 Uncoated T10 K20 * * Pricegroup 22 22 Coated T10C T10R K20C * * * * PriceK20R group 32 32 31

Pitch TPI 14 11

QuadThread Internal insertsR=0.107P

Pansarrohrgewinde (PG)Internal threading Catalog number 10N 18PG 10N 16PG Dimensions l s t h .394 .094 .047 .026 .394 .094 .047 .030 Uncoated T10 K20 * * Pricegroup 5 5 Coated T10C T10R K20C * * PriceK20R group 15 15

R=0.107P

Pitch TPI 18 16

R=0.107P

Pansarrohrgewinde (PG)External and Internal threading Catalog number 12X 20PG 12X 18PG 12X 16PG Dimensions l s t h .472 .094 .047 .024 .472 .094 .047 .026 .472 .094 .047 .030 Uncoated T10 K20 * * * Pricegroup 21 21 21 Coated T10C T10R K20C * * * * * * PriceK20R group 31 31 31

R=0.107P

Pitch TPI 20 18 16

Trapezoidal DIN 103Internal threading Pitch mm 1.5 2.0 3.0 Catalog number 10N 1.5TR 10N 2.0TR 10N 3.0TR Dimensions l s t h .394 .094 .047 .035 .394 .094 .047 .049 .394 .142 .071 .069 Uncoated T10 K20 * * * Pricegroup 5 5 6 Coated T10C T10R K20C * * * PriceK20R group 15 15 16

32

QuadThread Internal insertsTrapezoidal DIN 103External and Internal threading Pitch mm 1.5 2.0 3.0 4.0 5.0 6.0 Catalog number 12X 1.5TR 12X 2.0TR 12X 3.0TR 20X 4.0TR 20X 5.0TR 20X 6.0TR Dimensions l s t h .472 .094 .047 .035 .472 .094 .047 .049 .472 .142 .071 .069 .787 .181 .091 .089 .787 .268 .134 .108 .787 .268 .134 .138 Uncoated T10 K20 * * * * * * Pricegroup 21 21 22 23 24 24 Coated T10C T10R K20C * * * * * * PriceK20R group 31 31 32 33 34 34

R=0.221P

Round DIN 405Internal threading Catalog number 10N 10RD 10N 8RD Dimensions l s t h .394 .142 .071 .050 .394 .142 .071 .063 Uncoated T10 K20 * * Pricegroup 6 6 Coated T10C T10R K20C * * PriceK20R group 16 16

R=0.256P

Pitch TPI 10 8

R=0.221P

Round DIN 405Internal threading Catalog number 20N 6RD 20N 4RD Dimensions l s t h .787 .181 .091 .083 .787 .268 .134 .125 Uncoated T10 K20 * * Pricegroup 23 24 Coated T10C T10R K20C * * PriceK20R group * 33 * 34

R=0.256P

Pitch TPI 6 4

33

QuadThread Internal insertsACMEInternal threading Pitch TPI 16 14 12 10 8 Catalog number 10N 16ACME 10N 14ACME 10N 12ACME 10N 10ACME 10N 8ACME Dimensions l s t h .394 .094 .047 .040 .394 .094 .047 .044 .394 .094 .047 .052 .394 .142 .071 .065 .394 .142 .071 .079 Uncoated T10 K20 * * * * * Pricegroup 5 5 5 6 6 Coated T10C T10R K20C * * * * * PriceK20R group 15 15 15 16 16

ACMEExternal and Internal threading Pitch TPI 16 14 12 10 8 6 5 4 Catalog number 12X 16ACME 12X 14ACME 12X 12ACME 12X 10ACME 12X 8ACME 20X 6ACME 20X 5ACME 20X 4ACME Dimensions l s t h .472 .094 .047 .040 .472 .094 .047 .044 .472 .094 .047 .052 .472 .142 .071 .065 .472 .142 .071 .079 .787 .181 .091 .100 .787 .268 .134 .118 .787 .268 .134 .143 Uncoated T10 K20 * * * * * * * * Pricegroup 21 21 21 22 22 23 24 24 Coated T10C T10R K20C * * * * * * * * PriceK20R group 31 31 31 32 32 33 34 34

34

QuadThread Internal insertsSTUB ACMEInternal threading Pitch TPI 16 14 12 10 8 Catalog number 10N 16STACME 10N 14STACME 10N 12STACME 10N 10STACME 10N 8STACME Dimensions l s t h .394 .094 .047 .028 .394 .094 .047 .030 .394 .094 .047 .035 .394 .142 .071 .045 .394 .142 .071 .054 Uncoated T10 K20 * * * * * Pricegroup 5 5 5 6 6 Coated T10C T10R K20C * * * * * PriceK20R group 15 15 15 16 16

STUB ACMEExternal and Internal threading Pitch TPI 16 14 12 10 8 6 5 4 Catalog number 12X 16STACME 12X 14STACME 12X 12STACME 12X 10STACME 12X 8STACME 20X 6STACME 20X 5STACME 20X 4STACME Dimensions l s t h .472 .094 .047 .028 .472 .094 .047 .030 .472 .094 .047 .035 .472 .142 .071 .045 .472 .142 .071 .054 .787 .181 .091 .067 .787 .268 .134 .078 .787 .268 .134 .093 Uncoated T10 K20 * * * * * * * * Pricegroup 21 21 21 22 22 23 24 24 Coated T10C T10R K20C * * * * * * * * PriceK20R group 31 31 31 32 32 33 34 34

35

QuadThread Internal inserts30 30 l47

NPTInternal threading Catalog number 10N 18NPT 10N 14NPT 10N 11.5NPT Dimensions l s t h .394 .094 .047 .041 .394 .094 .047 .054 .394 .142 .071 .066 Uncoated T10 K20 * * * Pricegroup 5 5 6 Coated T10C T10R K20C * * * PriceK20R group 15 15 16

Pitch TPI 18 14 11.5

30

30 l47

NPTExternal and Internal threading Catalog number 12X 27NPT 12X 18NPT 12X 14NPT 12X 11.5NPT 20X 8NPT Dimensions l s t h .472 .094 .047 .028 .472 .094 .047 .041 .472 .094 .047 .054 .472 .142 .071 .066 .787 .181 .091 .096 Uncoated T10 K20 * * * * * Pricegroup 21 21 21 22 23 Coated T10C T10R K20C * * * * * * * PriceK20R group 31 31 31 32 * 33

Pitch TPI 27 18 14 11.5 8

NPTl47

Internal threading multitooth Catalog Dimensions No. Radial infeed per pass number l s t h teeth 1 2 3 4 20NR 8NPT2M .787 .268 .196 .096 2 .0295 .0276 .0276 .0110 Coated K20C * Pricegroup 54

Pitch TPI 8

36


NPTF DrysealInternal threading Catalog Dimensions number l s t h 10N 18NPTF .394 .094 .047 .040 10N 14NPTF .394 .094 .047 .054 10N 11.5NPTF .394 .142 .071 .065 Uncoated T10 K20 * * * Pricegroup 5 5 6 Coated T10C T10R K20C * * * PriceK20R group 15 15 16

0.125P

Pitch TPI 18 14 11.5

30 0.125P

30 l47

NPTF DrysealExternal and Internal threading Catalog number 12X 27NPTF 12X 18NPTF 12X 14NPTF 12X 11.5NPTF 20X 8NPTF Dimensions l s t h .472 .094 .047 .026 .472 .094 .047 .040 .472 .094 .047 .054 .472 .142 .071 .065 .787 .181 .091 .095 Uncoated T10 K20 * * * * * Pricegroup 21 21 21 22 23 Coated T10C T10R K20C * * * * * * * * * PriceK20R group 31 31 31 32 * 33

Pitch TPI 27 18 14 11.5 8

NPT, Line Pipe

NPTF Dryseal

NPT and Line Pipe have clearance on the top and bottom of the thread. QuadThread NPT profiles also fit the tolerances for Line Pipe profiles.

NPTF Dryseal gives a tight fit. This is accomplished when the pipe components are fitted together, as the top of the thread is deformed by the corresponding thread root.

37


API RDExternal and Internal threading Catalog number 12X 10APIRD 20X 8APIRD Dimensions l s t h .472 .142 .071 .057 .787 .181 .091 .073 Uncoated T10 K20 * * Pricegroup 22 23 Coated T10C T10R K20C * * PriceK20R group 32 33

Pitch TPI 10 8

APIInternal threading. Cassette QNR/L 63-20API must be used. Pitch TPI 4 4 4 4 Catalog number 20NR 4API384 20NR 4API386 20NR 4API504 20NR 4API506 Dimensions t h R .134 .1214 .038 .134 .1218 .038 .134 .1473 .025 .134 .1478 .025 API Code V-0.038R V-0.038R V-0.050 V-0.050 Coated K20C * * * * Pricegroup 34 34 34 34 l .787 .787 .787 .787 s .268 .268 .268 .268 Fc TPF .065 3 .065 2 .050 3 .050 2

38

QuadThread Internal toolholders 10 and 11

Toolholderswith internal coolant Catalog number QNR 0375 4-10 QNR 050 45-10 QNR 0625 5-10 QNR 075 6-10 QNL 0375 4-10 QNL 050 45-10 QNL 0625 5-10 QNL 075 6-10 Dimensions l D min 4.0 .54 4.5 .65 5.0 .75 6.0 .92 4.0 .54 4.5 .65 5.0 .75 6.0 .92 Helix angles 1.5 0 98.5 * * * * * * * * * * * * * * * * * * * * Pricegroup 228 228 229 229 228 228 229 229 d .375 .50 .625 .75 .375 .50 .625 .75 f .271 .367 .396 .458 .271 .367 .396 .458 3 * * * * * * * *

Tungsten alloy toolholdersDensimet with internal coolant Catalog number QNR 0375 6-D-10 QNR 050 6-D-10 QNR 0625 7-D-10 Dimensions l D min 6.0 .54 6.0 .65 7.0 .75 Helix angles 1.5 0 98.5 * * * Pricegroup 241 241 242 d .375 .50 .625 f .271 .367 .396 3

When overhanging is an issue, these tools are designed to reduce the risk of vibration and deflection.

Toolholderswith internal coolant Catalog number QNR 100 7-11 QNL 100 7-11 Dimensions l D min 7.0 1.20 7.0 1.20 Helix angles 1.5 0 98.5 * * * * Pricegroup 235 235 d 1.00 1.00 f .59 .59 3 * *

39

QuadThread Internal toolholders 12 and 20

Cassette type toolholderswith internal coolant Catalog number QNR 200/150 7-C50 QNR 200 10-C50 QNR 250/150 8-C50 QNR 250 12-C63 QNL 200/150 7-C50 QNL 200 10-C50 QNL 250/150 8-C63 QNL 250 12-C63 Dimensions l l2 f 7.0 3.0 1.18 10.0 - 1.18 8.0 4.0 1.48 12.0 - 1.48 7.0 3.0 1.18 10.0 - 1.18 8.0 4.0 1.48 12.0 - 1.48 Cassettes Insert 12... Insert 20... QNR 50-12 QNR 50-12 QNR 50-12 QNR 63-12 QNR 63-20 QNL 50-12 QNL 50-12 QNL 50-12 QNL 63-12 QNL 63-20 Stock standard * * * * * * * * Pricegroup 233 233 233 234 233 233 233 234 d 1.5 2.0 1.5 2.5 1.5 2.0 1.5 2.5 d2 2.0 2.0 2.5 2.5 2.0 2.0 2.5 2.5 D 2.20 2.20 3.15 3.15 2.20 2.20 3.15 3.15

NOTE! Standard is 0.7, not 1.5

Internal standard cassettesInsert 12 12 20 12 12. 20 0.7 Stock standard () 0 * * * * * * 98.5 Pricegroup 219 219 219 219 219 219

Catalog number QNR 50-12 QNR 63-12 QNR 63-20 QNL 50-12 QNL 63-12 QNL 63-20

Internal API cassettesCatalog number QNR 63-20API QNL 63-20API Insert 20N 20N 1.5 * * Stock standard () 0 * * 98.5 * * Pricegroup 219 219

NOTE! The following profiles can be used for external and internal threading. Partial profile Trapezoidal TPT Whitworth ACME NPTF BSPT STUB ACME API Round 40

WARNING! ISO Metric and Unified have different profiles for external and internal threading.

QuadThread Internal toolholdersf-DimensionFor some inserts the f-dimension is displaced according to the f2-dimension in the table. Dimensions s .094 .142 .094 .142 .142 .142 .181 .268 L .394 .394 .472 .472 .472 .472 .787 .787 f2 0 .047 0 .047 0 .047 0 .087

Helix angle 0.7 is standard and does not need to be shown when ordering cassettes, for instance, QNR50-12. All other helix angles should be shown after the cassette catalog number, for instance, QNR6320-98.5.

ScrewsCatalog number STS T9xM3 STS T9xM3 STS T9xM3 STS T15xM5 Used for Insert 10 Insert 11 Insert 12 Insert 20 Pricegroup 221 221 221 221

KeysCatalog number Torx T9 Torx T15 Used for STS T9xM3 STS T15xM5 Pricegroup 222 222

41

QuadThread CBN Threading by hard turningCBNWhen threading hardened steel, the usage of super-hard cutting material is gaining ground. The hard turning is made with cubic boron nitride (CBN). CBN is today an established turning and milling material, it increases productivity and saves on coolants. The single CBN edge on the QuadThread insert is made of a well-proven quality from a leading global supplier of CBN.

Machinable materialsThe QuadThread CBN inserts are suitable for threading in hardened tool steels of 4565 HRC.

Threading profilesMetric threads as partial profile with pitches from 0.52.5 mm (48-10 TPI) can be produced. The minimum possible thread diameters are depending on the pitch. Threads with cutting interruptions, for example safety grooves, can be produced when first phased.Modified flank infeed

MachiningRecommended cutting speed, Vc, is 80120 m/min. No pre-threading is necessary. A modified flank infeed in Z-axis of 28 is to be used. A constant infeed in X-axis is made with 0.050.09 mm per pass. The number of passes should be calculated according to the thread depth. In case of constant cutting the machining can be done dry or wet. With interrupted cutting the machining should be done dry.

42

QuadThread CBN insertsPartial Profile 60External Threading Pitch mm 0.5 0.75 1.0 1.5 2.0 2.5 Catalog number 12E 0.5ISO 12E 0.75ISO 12E 1.0ISO 12E 1.5ISO 12E 2.0ISO 12E 2.5ISO Dimensions s .094 .094 .094 .094 .094 .142 Pricegroup 61 61 61 61 61 62 l .472 .472 .472 .472 .472 .472 t .047 .047 .047 .047 .047 .071 CBN 250 *

Partial Profile 60Internal Threading Pitch mm 0.5 0.75 1.0 1.5 1.75 2.0 Catalog number 10N 0.5ISO 10N 0.75ISO 10N 1.0ISO 10N 1.5ISO 10N 1.75ISO 10N 2.0ISO Dimensions s .094 .094 .094 .094 .094 .094 Pricegroup 65 65 65 65 65 65 l .394 .394 .394 .394 .394 .394 t .047 .047 .047 .047 .047 .047 CBN 250 * * * * * * = Stock standard * = Limited stock

Please inquire for other profiles, as well as other pitches.

43

QuadCutOff

Parting off and grooving

Cutting tools in High Speed Steel (HSS)Carbide inserts are used for most standard parting off and grooving. For special applications like thin wall tubes, soft materials or low cutting speeds, a high speed steel insert might prove more efficient. QuadCutOff is made of HSS and has a TiN-coating. Precision grinding of these tools gives extremely sharp cutting edges, which has an advantage in the above-mentioned applications.

Cutting DataThe table gives recommended cutting speeds in feet/min. Material Low-carbon steel < 650N/mm2 Carbon steel 650-850N/mm2 Alloyed tool steel and hest-resistant steel Stainless steel Cast iron HB 150-250 Non-ferrous materials HSSC 130-200 100-130 100-130 100-130 70-100 -700

FeedThe table gives the recommended feed rate in inch/revolution for different inserts. Material Low carbon steel < 650N/mm2 Carbon steel 650-850N/mm2 Alloyed tool steel and heat-resistant steel Stainless steel Cast iron HB 180-250 Non-ferrous materials Q16-1.0 .0030-.0040 .0016-.0024 .0016-.0024 .0020-.0024 .0020-.0024 -.0080 Q16-1.2 .0030-.0040 .0020-.0024 0020-.0024 .0020-.0024 .0020-.0024 -.0080 Q16-1.5 .0040-.0060 .0020-.0040 .0020-.0040 .0020-.0040 .0020-.0040 -.0100 Q25-1.5 .0040-.0060 .0020-.0040 .0020-.0040 .0020-.0040 .0020-.0040 -.0100 Q25-2.0 .0040-.0080 .0030-.0060 .0030-.0060 .0030-.0060 .0030-.0060 -.0100

Parting-off diameterThe maximum parting-off dia on a solid bar is .512 with the Q16 insert and .787 with the Q25 insert. It is possible to cut larger diameters of tube as the tool does not travel to the center of the component. Please check the diagram below for the most suitable insert for your application. Example: D = 1.102 d = .787 Choose Q25-insert

44

QuadCutOff insertsStraightParting-off Catalog number Q16- 1.0 Q16- 1.2 Q16- 1.5 Q25- 1.5 Q25- 2.0 Dimensions l s 0.05 .63 .039 .63 .047 .63 .059 .984 .059 .984 .079 Max. cut-off diameter .512 .512 .512 .787 .787 TiN-coated HSSC Pricegroup 371 371 371 373 373

AngularParting-off Catalog number Q16-R6-1.2 Q16-R12-1-1.2 Q16-R6-1.5 Q16-R12-1.5 Q16-L6-1.2 Q16-L12-1.2 Q16-L6-1.5 Q16-L12-1.5 Q25-R6-1.5 Q25-R12-1.5 Q25-R6-2.0 Q25-R12-2.0 Q25-L6-1.5 Q25-L12-1.5 Q25-L6-2.0 Q25-L12-2.0 Dimensions l s 0.05 V .63 .047 6 .63 .047 12 .63 .059 6 .63 .059 12 .63 .047 6 .63 .047 12 .63 .059 6 .63 .059 12 .984 .059 6 .984 .059 12 .984 .079 6 .984 .079 12 .984 .059 6 .984 .059 12 .984 .079 6 .984 .079 12 Max. cut-off diameter .512 .512 .512 .512 .512 .512 .512 .512 .787 .787 .787 .787 .787 .787 .787 .787 TiN-coated HSSC Pricegroup 372 372 372 372 372 372 372 372 374 374 374 374 374 374 374 374

Circlip groovesExternal grooving Catalog number Q16- C0.5 Q16- C0.6 Q16- C0.7 Q16- C0.8 Q16- C0.9 Q16- C1.0 Q16- C1.1 Q16- C1.3 Q25- C1.6 Q25- C1.85 Dimensions l s 0.02 .63 .0213 .63 .0252 .63 .0291 .63 .0331 .63 .0370 .63 .0410 .63 .0476 .63 .0555 .984 .0673 .984 .0772 Max. depth .039 .039 .039 .039 .039 .039 See page See page See page See page TiN-coated HSSC Pricegroup 372 372 372 372 372 372 372 372 374 374 45 Circlip .015 .025 .035 .042 .050 .062 -

44 44 44 44

QuadCutOff toolholdersToolholdersCatalog number GEX 0375 5-Q16 GEX 050 5-Q16 GEX 0625 5-Q16 GEX 075 5-Q16 GEX 050 6-Q25 GEX 0625 6-Q25 GEX 075 6-Q25 GEX 100 6-Q25 GEX 125 6-Q25 H .375 .50 .625 .75 .50 .625 .75 1.00 1.25 Dimensions B l .472 5.0 .472 5.0 .472 5.0 .472 5.0 .630 6.0 .630 6.0 .630 6.0 .630 6.0 .630 6.0 E .75 .75 .75 .75 1.18 1.18 1.18 1.18 1.18 Insert Q16 Q16 Q16 Q16 Q16 Q25 Q25 Q25 Q25 Stock Pricestandard (k) group 379 379 379 379 379 380 380 380 380

GEX 1010 index Q16Catalog number GEX 1010-INDEX-Q16 H 10 Dimensions (mm) B l E 10 60 19 Insert Q16 Stock Pricestandard (k) group 379

ScrewsCatalog number STS T9xM3 STS T15xM5 Used for Insert Q16 Insert Q25 Pricegroup 221 221

KeysCatalog number Torx T9 Torx T15 46 Used for STS T9xM3 STS T15xM5 Pricegroup 222 222

QuadThread

QuadThread External

QuadThread Internal

QuadCutOff

Scandinavian Tool Systems Inc. PO Box 917, 931 East Water Street Chillicothe, OH 45601 Phone +1 800-722-6874 Fax +1 740-775-2314 [email protected] www.ststooling.com

Scandinavian Tool Systems AB Box 59, SE-793 12 Insjn, Sweden Phone +46 (0)247 410 20 Fax +46 (0)247 415 71 [email protected] www.scandinavian-tool.se

STSQuadThreadkorr5

Documents

Transcript of STSQuadThreadkorr5