STRAIL Road Marking-S Installation Instructions 02
-
Upload
pura-paula-liviana -
Category
Documents
-
view
216 -
download
0
Transcript of STRAIL Road Marking-S Installation Instructions 02
8/9/2019 STRAIL Road Marking-S Installation Instructions 02
http://slidepdf.com/reader/full/strail-road-marking-s-installation-instructions-02 1/5
STRAIL® road marking-SApplication instructionsSubject to technical modifications / November 2013 / TNA-WMO
STRAIL® level crossing systems / STRAILastic track damping systems
KRAIBURG STRAIL® GmbH & Co. KG • D-84529 Tittmoning • Goellstrasse 8
Phone + 49(0)8683/701-0 • Fax -126 • [email protected] • www.strail.com • www.strailastic.com
www.strail.com / www.strailastic.com
8/9/2019 STRAIL Road Marking-S Installation Instructions 02
http://slidepdf.com/reader/full/strail-road-marking-s-installation-instructions-02 2/5
Installation instructions STRAIL® road marking-S ¬ page 2/5 November 2013 / Subject to technical modifications
STRAIL® level crossing systems / D-84529 Tittmoning • Phone +49(0)8683/701-0 • Fax -126 • [email protected] • www.strail.com
# 1 / REQUIREMENTS FOR USE
¬ ambient temperature > min. + 5° C
¬ surface > no residual moisture!
> clean swept
> free from oil and grease
Do not use STRAIL® Road marking-S in closed rooms or without suffi cient ventilation!
# 2 / OPERATING MATERIALS
¬ STRAIL®
Road marking-S / in 400 ml cans1 packaging unit (VPE) =^ 6 cans
¬ STRAIL® Primer / in 0.5 l bottles
¬ Glass beads (OPTIONAL)
# 3 / TOOLS
Paint roller
(frame and roller)
Chalk line
(Chalk line and paint)
Template (available in
different sizes)
optional STRAIL®
marking stick
Personal protective equipment (protective glasses, protective clothing and gloves)
Material for cleaning of the panel surface (broom, leaf blower, spatula)
8/9/2019 STRAIL Road Marking-S Installation Instructions 02
http://slidepdf.com/reader/full/strail-road-marking-s-installation-instructions-02 3/5
Installation instructions STRAIL® road marking-S ¬ page 3/5 November 2013 / Subject to technical modifications
STRAIL® level crossing systems / D-84529 Tittmoning • Phone +49(0)8683/701-0 • Fax -126 • [email protected] • www.strail.com
# 4 / PREPARATION
¬ Begin by cleaning the surface of the rubber plates
with a broom, a leaf blower or a similar tool.
The Road marking may only be applied on dry
surfaces! No residual moisture!
¬ Use the chalk line to mark the lines (areas).
Colour: red
¬ Applying the STRAIL® - Primer:
Apply the STRAIL® - Primer with a hand roller
corresponding to the marked lines, so that the
entire surface is wet.
The paint must be sprayed on within a maximum
of 5 minutes after applying the STRAIL® - Primer.
¬ Position the template corresponding to the lines you
marked before.
# 5 / APPLYING THE ROAD MARKING WITH A SPRAYCAN
8/9/2019 STRAIL Road Marking-S Installation Instructions 02
http://slidepdf.com/reader/full/strail-road-marking-s-installation-instructions-02 4/5
Installation instructions STRAIL® road marking-S ¬ page 4/5 November 2013 / Subject to technical modifications
STRAIL® level crossing systems / D-84529 Tittmoning • Phone +49(0)8683/701-0 • Fax -126 • [email protected] • www.strail.com
¬ Preparing the road marking
Remove the red press button from the can end and
attach it to the designated dowel pin on the
underside of the can.
Press the red button down as far as it will go and
hold the position. Afterwards, shake the can strongly
for approx. 1 minute so that all the components
contained blend well.
¬ Apply the paint evenly and opaquely using the spray
can (distance: approx. 20 cm).
The can has an overhead outlet and it must be used
that way.
Optional > for better handling you can include our
marking stick in your order. The spray
can is put into it and is activated by the
mechanism at the handle.
The template can be removed immediately after the
completion of the spraying process.
# 7 / OPTIONAL > GLASS BEADS
Optional glass beads can be sprinkled into the freshly-applied
paint to achieve good night visibility (reflection effect).
8/9/2019 STRAIL Road Marking-S Installation Instructions 02
http://slidepdf.com/reader/full/strail-road-marking-s-installation-instructions-02 5/5
Installation instructions STRAIL® road marking-S ¬ page 5/5 November 2013 / Subject to technical modifications
STRAIL® level crossing systems / D-84529 Tittmoning • Phone +49(0)8683/701-0 • Fax -126 • [email protected] • www.strail.com
# 8 / CLEANING
Clean all the tools thoroughly after use (marking stick, template).
# 9 / PLEASE NOTE
¬ Surface skinning: after approx. 2 hours
¬ Trafficability: after approx. 3-4 hours
¬ Thoroughly dry: after approx. 8 hours
All consumables are perishable after the package had been opened!
Open cans should be used up immediately if possible!
Store the cans in dry condition and protected from frost!
Material safety data sheets are sent out upon request.
PLEASE NOTE
Please read the installation instructions carefully and use STRAIL® road marking-S in compliance with
our manufacturer’s guidelines or request our assistance. We can only provide a guarantee/warranty if the
installation has been carried out in accordance with our stipulations.
This data sheet is only valid in its latest version and is not updated automatically.