STR-DA5300ES

STR-DA5300ESSERVICE MANUALVer. 1.6 2009.05

US Model Canadian Model AEP Model UK Model Chinese Model

This receiver incorporates Dolby* Digital and Pro Logic Surround and the DTS** Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, Surround EX, and the double-D symbol are trademarks of Dolby Laboratories. ** Manufactured under license from DTS, Inc. DTS, DTS-ES and Neo:6 are registered trademarks of DTS, Inc. and DTS-HD Master Audio, DTS-HD High Resolution Audio and DTS 96/24 are trademarks of DTS, Inc.

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS (US model)POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 8 ohm loads, both channels driven, from 20 20,000 Hz; rated 120 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier sectionPOWER OUTPUT (US and Canadian models) Rated Power Output at Stereo Mode1) 2) (8 ohms 20 Hz 20 kHz, THD 0.09%): 120 W + 120 W Reference Power Output at Stereo Mode (4 ohms 20 Hz 20 kHz, THD 0.15%): 120 W + 120 W Reference Power Output (8 ohms 1 kHz, THD 0.7%) FRONT2): 130 W + 130 W CENTER2): 130 W SURROUND2): 130 W + 130 W SURROUND BACK2): 130 W + 130 W

Reference Power Output (4 ohms 1 kHz, THD 0.7%) FRONT2): 120 W + 120 W CENTER2): 120 W SURROUND2): 120 W + 120 W SURROUND BACK2): 120 W + 120 W1) Depending

on the sound field settings and the source, there may be no sound output. 2) Measured under the following conditions: Power requirements: 120 V AC, 60 Hz

(AEP, Russian, Ukrainian, UK and Chinese models) Rated Power Output at Stereo Mode1) 2) (8 ohms 1 kHz, THD 0.7%): 125 W + 125 W Reference Power Output at Stereo Mode (4 ohms 1 kHz, THD 0.7%): 125 W + 125 W

Reference Power Output (8 ohms 20 Hz 20 kHz, THD 0.09%) FRONT2): 120 W + 120 W CENTER2): 120 W SURROUND2): 120 W + 120 W SURROUND BACK2): 120 W + 120 W Reference Power Output (4 ohms 20 Hz 20 kHz, THD 0.15%) FRONT2): 120 W + 120 W CENTER2): 120 W SURROUND2): 120 W + 120 W SURROUND BACK2): 120 W + 120 W Reference Power Output at Stereo Mode (8 ohms 1 kHz, THD 10%): 150 W + 150 W

Continued on next page

MULTI CHANNEL AV RECEIVER9-887-741-072009E05-1 2009.05

Sony CorporationAudio&Video Business Group Published by Sony Techno Create Corporation

STR-DA5300ESVer. 1.2

Reference Power Output at Stereo Mode (4 ohms 1 kHz, THD 10%): 150 W + 150 W Reference Power Output (8 ohms 1 kHz, THD 10%) FRONT2): 150 W + 150 W CENTER2): 150 W SURROUND2): 150 W + 150 W SURROUND BACK2): 150 W + 150 W Reference Power Output (4 ohms 1 kHz, THD 10%) FRONT2): 150 W + 150 W CENTER2): 150 W SURROUND2): 150 W + 150 W SURROUND BACK2): 150 W + 150 W1)

EQUALIZERGain levels 10 dB, 1 dB step

Tuning range 87.5 108.0 MHz Antenna (aerial) FM wire antenna (aerial) Antenna (aerial) terminals 75 ohms, unbalanced

FM tuner section

Power consumption (during standby mode) 0.7 W (when HDMI Control and RS-232C Control is set to OFF) Dimensions 430 175 430 mm (width/height/depth) including projecting parts and controls Mass (Approx.) 16.0 kg

AM tuner sectionTuning range (US and Canadian models) With 10-kHz tuning scale 530 1,710 kHz 3) With 9-kHz tuning scale 531 1,710 kHz 3) (AEP, Russian, Ukrainian, UK and Chinese models) With 9-kHz tuning scale 531 1,602 kHz Antenna (aerial)3)

Supplied accessoriesOperating Instructions Quick Setup Guide (1) HDMI CONTROL Guide (1) GUI Menu List (1) Optimizer microphone ECM-AC1 (1) FM wire antenna (aerial) (1) AM loop antenna (aerial) (1) AC power cord (mains lead) (1) Remote commander RM-AAL008 (1) (US and Canadian models) Remote commander RM-AAL009 (1) (AEP, Russian, Ukrainian, UK and Chinese models) Remote commander RM-AAU016 (1) R6 (size-AA) batteries (4)

Loop antenna (aerial)

Depending on the sound field settings and the source, there may be no sound output. 2) Measured under the following conditions: Power requirements: 230 V AC, 50/60 Hz (in countries/area in Europe other than the U.K.) 240 V AC, 50/60 Hz (in the U.K. and general area) 220 V AC, 50 Hz (Chinese model only)

You can change the AM tuning scale to either 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down TUNING MODE, press POWER on the receiver. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.

Design and specifications are subject to change without notice.

Video sectionInputs/Outputs Video: 1 Vp-p, 75 ohms COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms PB/CB: 0.7 Vp-p, 75 ohms PR/CR: 0.7 Vp-p, 75 ohms 80 MHz HD Pass Through

Frequency responsePHONO MULTI CHANNEL INPUT, SA-CD/CD, MD/DAT, DVD/BD, TV, SAT/CATV, TAPE/CD-R, VIDEO 1/2/3 RIAA equalization curve 0.5 dB 10 Hz 100 kHz 3 dB

HDMI VideoInput/Output (HDMI Repeater block) 640 480p@60Hz 720 [email protected]/60Hz 1440 [email protected]/60Hz (pixel sent 2times) 1280 [email protected]/60Hz 1920 [email protected]/60Hz 1920 [email protected]/60Hz 720 576p@50Hz 1440 576p@50Hz (pixel sent 2times) 1280 720p@50Hz 1920 1080i@50Hz 1920 1080p@50Hz 1920 1080p@24Hz

Inputs (Analog)PHONO Sensitivity: 2.5mV Impedance: 50kohms S/N: 90dB (A, 20 kHz LPF) Sensitivity: 150mV Impedance: 50kohms S/N: 100dB (A, 20 kHz LPF)

MULTI CHANNEL INPUT, SA-CD/CD, MD/DAT, DVD/BD, TV, SAT/CATV, TAPE/CD-R, VIDEO 1/2/3

Inputs (Digital)DVD/BD, VIDEO 2, SA-CD/CD (Coaxial) VIDEO 1, TV, SAT/CATV, TAPE/CDR, MD/DAT (Optical) Impedance: 75ohms S/N: 96dB (A, 20 kHz LPF) S/N: 96 dB (A, 20 kHz LPF)

GeneralPower requirements 120 V AC, 60 Hz (US and Canadian models) 230 V AC, 50/60Hz (in countries/area in Europe other than the U.K.) 230 240V AC, 50/60Hz (in the U.K. and general area) 220V AC, 50Hz (Chinese model only) Power output (DIGITAL MEDIA PORT) DC OUT:5 V, 700 mA Power consumption 480 W/580 VA (US/ Canada) 480 W (AEP, Russian, Ukrainian, UK and Chinese models)

OutputsMD/DAT (REC OUT), VIDEO 1, ZONE 2, ZONE 3 (AUDIO OUT) Voltage:150mV Impedance: 1kohm

FRONT L/R, CENTER, Voltage: 2V SURROUND L/R, Impedance: 1kohm SURROUND BACK L/R, SUB WOOFER

2


Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, metallized knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The limit indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A)To Exposed Metal Parts on Set

0.15 F

1.5 k

AC voltmeter (0.75 V)

Earth Ground

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

Fig. A. Using an AC voltmeter to check AC leakage.

ATTENTION AU COMPOSANT AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFIS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PICES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPLMENTS PUBLIS PAR SONY.

3

STR-DA5300ES

TABLE OF CONTENTS 1. 2. 3.3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10.

SERVICING NOTES ..............................................

5

GENERAL .................................................................. 11 DISASSEMBLYDisassembly Flow .......................................................... Case ................................................................................ SP-TM Board, Tuner (FM/AM) ..................................... D-CONNECT Board, DSP Board, DIGITAL Board, CIS Board and CONTROL Board .................................. D-VIDEO Board ............................................................. Front Panel Section ........................................................ S-VIDEO Board and A-VIDEO Board .......................... FLI-1.8REG Board and ANALOG Board ...................... Power Transformer (T001), E-VOL Board and MAIN Board ................................................................... Heat Sink Section ........................................................... 19 20 20 21 21 22 22 23 24 25

6-36. 6-37. 6-38. 6-39. 6-40. 6-41. 6-42. 6-43. 6-44. 6-45. 6-46. 6-47. 6-48. 6-49. 6-50. 6-51. 6-52. 6-53. 6-54. 6-55. 6-56. 6-57. 6-58. 6-59. 6-60. 6-61. 6-62. 6-63. 6-64. 6-65. 6-66. 6-67. 6-68. 6-69. 6-70. 6-71. 6-72. 6-73. 6-74. 6-75. 6-76. 6-77. 6-78. 6-79. 6-80. 6-81. 6-82. 6-83. 6-84. 6-85. 6-86. 6-87. 6-88. 6-89. 6-90. 6-91.

4. 5. 6.6-1. 6-2. 6-3. 6-4. 6-5. 6-6. 6-7. 6-8. 6-9. 6-10. 6-11. 6-12. 6-13. 6-14. 6-15. 6-16. 6-17. 6-18. 6-19. 6-20. 6-21. 6-22. 6-23. 6-24. 6-25. 6-26. 6-27. 6-28. 6-29. 6-30. 6-31. 6-32. 6-33. 6-34. 6-35.

TEST MODE ............................................................. 26 ELECTRICAL ADJUSTMENTS ........................ 30 DIAGRAMSBlock Diagram CONTROL Section .......................... Block Diagram DSP Section ..................................... Block Diagram DIGITAL AUDIO Section ............... Block Diagram HDMI Section (1/2) ......................... Block Diagram HDMI Section (2/2) ......................... Block Diagram VIDEO PROCESS Section .............. Block Diagram ANALOG AUDIO Section .............. Block Diagram POWER AMP Section ..................... Block Diagram VIDEO Section (1/2) ....................... Block Diagram VIDEO Section (2/2) ....................... Block Diagram PANEL, CIS, XM/ SIRIUS RECEIVER, DMPORT Section ..................... Block Diagram POWER SUPPLY Section ............... Printed Wiring Board MAIN Board (Component Side) ............................... Printed Wiring Board MAIN Board (Conductor Side) ................................. Schematic Diagram MAIN Board (1/4) .................... Schematic Diagram MAIN Board (2/4) .................... Schematic Diagram MAIN Board (3/4) .................... Schematic Diagram MAIN Board (4/4) .................... Printed Wiring Board DIGITAL Board (Component Side) .......................... Printed Wiring Board DIGITAL Board (Conductor Side) ............................ Schematic Diagram DIGITAL Board (1/4) ............... Schematic Diagram DIGITAL Board (2/4) ............... Schematic Diagram DIGITAL Board (3/4) ............... Schematic Diagram DIGITAL Board (4/4) ............... Printed Wiring Board DSP Board (Side A) ............... Printed Wiring Board DSP Board (Side B) ............... Schematic Diagram DSP Board (1/4) ....................... Schematic Diagram DSP Board (2/4) ....................... Schematic Diagram DSP Board (3/4) ....................... Schematic Diagram DSP Board (4/4) ....................... Printed Wiring Board ANALOG Board (Component Side) ......................... Printed Wiring Board ANALOG Board (Conductor Side) ........................... Schematic Diagram ANALOG Board (1/3) .............. Schematic Diagram ANALOG Board (2/3) .............. Schematic Diagram ANALOG Board (3/3) .............. 33 34 35 36 37 38 39 40 41 42 43 44 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

Printed Wiring Board E-VOL Board ......................... 69 Schematic Diagram E-VOL Board (1/2) ................... 70 Schematic Diagram E-VOL Board (2/2) ................... 71 Printed Wiring Boards CONNECTOR Section ......... 72 Schematic Diagram CONNECTOR Section ............. 73 Printed Wiring Board TEMPERATURE DETECTION Board .................... 74 Schematic Diagram TEMPERATURE DETECTION Board .................... 74 Printed Wiring Board A-CLASS AMP Board ........... 75 Schematic Diagram A-CLASS AMP Board (1/2) ..... 76 Schematic Diagram A-CLASS AMP Board (2/2) ..... 77 Printed Wiring Board POWER AMPLIFIER Board .................................... 78 Schematic Diagram POWER AMPLIFIER Board .... 79 Printed Wiring Board PROTECTOR (F-C) Board .... 80 Schematic Diagram PROTECTOR (F-C) Board ....... 81 Printed Wiring Boards PROTECTOR (SB/SURR) Section ........................... 82 Schematic Diagram PROTECTOR (SB/SURR) Section ........................... 83 Printed Wiring Board BIAS Board ............................ 84 Schematic Diagram BIAS Board .............................. 85 Printed Wiring Board SP-TM Board ......................... 86 Schematic Diagram SP-TM Board ............................ 87 Printed Wiring Board D-VIDEO Board (Component Side) ......................... 88 Printed Wiring Board D-VIDEO Board (Conductor Side) ........................... 89 Schematic Diagram D-VIDEO Board (1/12) ............ 90 Schematic Diagram D-VIDEO Board (2/12) ............ 91 Schematic Diagram D-VIDEO Board (3/12) ............ 92 Schematic Diagram D-VIDEO Board (4/12) ............ 93 Schematic Diagram D-VIDEO Board (5/12) ............ 94 Schematic Diagram D-VIDEO Board (6/12) ............ 95 Schematic Diagram D-VIDEO Board (7/12) ............ 96 Schematic Diagram D-VIDEO Board (8/12) ............ 97 Schematic Diagram D-VIDEO Board (9/12) ............ 98 Schematic Diagram D-VIDEO Board (10/12) .......... 99 Schematic Diagram D-VIDEO Board (11/12) ......... 100 Schematic Diagram D-VIDEO Board (12/12) ......... 101 Printed Wiring Board A-VIDEO Board (Component Side) ........................ 102 Printed Wiring Board A-VIDEO Board (Conductor Side) .......................... 103 Schematic Diagram A-VIDEO Board (1/4) ............. 104 Schematic Diagram A-VIDEO Board (2/4) ............. 105 Schematic Diagram A-VIDEO Board (3/4) ............. 106 Schematic Diagram A-VIDEO Board (4/4) ............. 107 Printed Wiring Board S-VIDEO Board .................... 108 Schematic Diagram S-VIDEO Board ....................... 109 Printed Wiring Board VIDEO3 Board ...................... 110 Schematic Diagram VIDEO3 Board ........................ 111 Printed Wiring Board CONTROL Board (Component Side) ...................... 112 Printed Wiring Board CONTROL Board (Conductor Side) ........................ 113 Schematic Diagram CONTROL Board (1/2) ........... 114 Schematic Diagram CONTROL Board (2/2) ........... 115 Printed Wiring Board CIS Board .............................. 116 Schematic Diagram CIS Board ................................ 117 Printed Wiring Board DISPLAY Board ................... 118 Schematic Diagram DISPLAY Board ...................... 119 Printed Wiring Boards PANEL Section .................... 120 Schematic Diagram PANEL Section ........................ 121 Printed Wiring Board DC-DC Board ....................... 122 Schematic Diagram DC-DC Board .......................... 123

4

STR-DA5300ES Ver. 1.2 SECTION 1 SERVICING NOTES6-92. Printed Wiring Board AC Board (TYPE A) ............. 124 6-93. Printed Wiring Board AC Board (TYPE B) ............. 124 6-94. Schematic Diagram AC Board ................................. 125 UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. NOTE OF REPLACING THE IC3601 ON THE D-VIDEO BOARD Replacement of IC3601 on the D-VIDEO board used in this set requires a special tool. NOTE WHEN THE AC BOARD IS REPAIRED (US and Canadian models only)Note: AEP, Russian, Ukrainian and UK models uses only TYPE B.

7.7-1. 7-2. 7-3. 7-4. 7-5. 7-6. 7-7. 7-8. 7-9.

EXPLODED VIEWSCase Section ................................................................... 173 DIGITAL Board Section ................................................ 174 D-VIDEO Board Section ................................................ 175 DISPLAY Board Section ................................................ 176 Front Panel Section ........................................................ 177 A-VIDEO Board Section ................................................ 178 ANALOG Board Section ............................................... 179 Heat Sink Section ........................................................... 180 MAIN Board Section ...................................................... 181

8.

ELECTRICAL PARTS LIST ............................... 182

Two types exist in the AC board for US and Canadian models. Repair after distinguishing which type it is referring to the figure below. AC Board (Component Side)

JW003

TYPE A : JW003 is not mounted. TYPE B : JW003 is mounted.Note 1: Refer NOTE WHEN THE AC BOARD IS REPAIRED (page 5) in servicing notes for how to distinguish TYPE A/B. Note 2: Refer to SUPPLEMENT-1 for the CONTROL, DIGITAL and DSP boards of printed wiring boards, schematic diagrams and electrical parts list of Russian and Ukrainian models. When repairing the set of US, Canadian, AEP and UK models, refer to either of original service manual/SUPPLEMENT-1 according to the set. Note 3: Refer to SUPPLEMENT-1 for the CONTROL, DIGITAL and DSP boards of printed wiring boards, schematic diagrams and electrical parts list of Chinese model. Refer to SUPPLEMENT-2 for the A-CLASS AMP, D-CONNECT and E-VOL boards of printed wiring boards, schematic diagrams and electrical parts list of Chinese model. When repairing the set except Chinese model, refer to either of original service manual/SUPPLEMENT-1/ SUPPLEMENT-2 according to the set.

5


MODEL IDENTIFICATION Back Panel

PART No.

UPDATE OF SOFTWARE OF IC2003 ON THE CONTROL BOARD, IC3610 ON THE D-VIDEO BOARD AND IC5208 ON THE DSP BOARD Perform operation of the following when the update of software of the IC2003 on the CONTROL board, IC3610 on the D-VIDEO board and IC5208 on the DSP board is necessary. Connect:

J1499Model US and Canadian models AEP and Chinese models UK model Russian and Ukrainian models PART No. 3-113-954-1[] 3-113-954-2[] 3-113-954-3[] 3-113-954-4[]

for PC

NOTE OF REPLACING THE IC3511 AND IC3513 ON THE D-VIDEO BOARD IC3511 and IC3513 on the D-VIDEO board cannot exchange with single. When IC3511 and IC3513 on the D-VIDEO board are damaged, exchange the entire mounted board. NOTE OF REPLACING THE IC5002 AND IC5202 ON THE DSP BOARD IC5002 and IC5202 on the DSP board cannot exchange with single. When IC5002 and IC5202 on the DSP board are damaged, exchange the entire mounted board.

Procedure: 1. Connect J1499 on the MAIN board and PC by using the RS232C cable. 2. Turn on the main power. 3. The update is executed by using PC. 4. When the update ends, turn off the main power. 5. Remove the RS-232C cable from the J1499 on the MAIN board and PC. ERROR MESSAGES If there is a malfunction, the display shows a code of two numbers and a message. You can check the condition of the system by the message. Refer to the following table to solve the problem. messages PROTECTOR cause and response Irregular current is output to the speakers, or the upper panel of the receiver is covered with something. The receiver will automatically turn off after a few seconds. Cheack the speakers connection and turn on the power again.

6


POWER AMP BLOCK SERVICE POSITION In checking the Power AMP block, prepare jig (extension cable J-2501-291-A: 2 mm Pitch, 12 cores, Length 300 mm/J-2501-311-A: 2 mm Pitch, 15 cores, Length 300 mm).

A-CLASS AMP board (CN1505) power AMP Block A-CLASS AMP board (CN1504) Connect the extension jig (J-2501-311-A) to the A-CLASS AMP board (CN1505) and E-VOL board (CN1202).

insulating sheet E-VOL board (CN1202)

Connect the extension jig (J-2501-291-A) to the A-CLASS AMP board (CN1504) and E-VOL board (CN1201).

E-VOL board (CN1201)

CONTROL BOARD SERVICE POSITION In checking the CONTROL board, prepare jig (extension cable J-2501-255-A: 1.25 mm Pitch, 10 cores, Length 300 mm/J-2501-258-A: 1.25 mm Pitch, 16 cores, Length 300 mm/J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm/J-2501-260-A: 1.25 mm Pitch, 20 cores, Length 300 mm).connect jig (extension cable J-2501-260-A) to the CONTROL board (CN2006) and MAIN board (CN1005). connect jig (extension cable J-2501-255-A) to the CONTROL board (CN2008) and MAIN board (CN1006). CONTROL board (CN2006) CONTROL board (CN2004) insulating sheet connect jig (extension cable J-2501-258-A) to the CONTROL board (CN2004) and D-CONNECT board (CN2403). connect jig (extension cable J-2501-259-A) to the CONTROL board (CN2005) and D-CONNECT board (CN2405). D-CONNECT board (CN2403)

CONTROL board (CN2008) CONTROL board (CN2005)

D-CONNECT board (CN2405) MAIN board (CN1006)

MAIN board (CN1005)

7


DIGITAL BOARD SERVICE POSITION In checking the DIGITAL board, prepare jig (extension cable J-2501-312-A: 1.25 mm Pitch, 11 cores, Length 300 mm).

CONTROL board (CN2002)

connect jig (extension cable J-2501-312-A) to the DIGITAL board (CN2203) and CONTROL board (CN2002).

DIGITAL board (CN2203)

D-VIDEO/S-VIDEO BOARDS SERVICE POSITION In checking the D-VIDEO board, prepare two jig (extension cable J-2501-259-A: 1.25 mm Pitch, 18 cores, Length 300 mm).

Connect jig (extension cable J-2501-259-A) to the D-VIDEO board (CN3508) and CONTROL board (CN2009). D-VIDEO board (CN3508) Connect jig (extension cable J-2501-259-A) to the D-VIDEO board (CN3507) and CONTROL board (CN2001).

D-VIDEO board (CN3507)


CONTROL board (CN2009) S-VIDEO board

8

STR-DA5300ES

A-VIDEO BOARD SERVICE POSITION In checking the A-VIDEO board, prepare jig (extension cable J-2501-257-A: 1.25 mm Pitch, 14 cores, Length 300 mm).

connect jig (extension cable J-2501-257-A) to the CONTROL board (CN2010) and A-VIDEO board (CN6507). A-VIDEO board (CN6507)


insulating sheet

ANALOG BOARD SERVICE POSITION In checking the ANALOG board, prepare jig (extension cable J-2501-258-A: 1.25 mm Pitch, 16 cores, Length 300 mm).

ANALOG board (CN602)

connect jig (extension cable J-2501-258-A) to the CONTROL board (CN2011) and ANALOG board (CN602).


insulating sheet

9

STR-DA5300ES

MAIN BOARD SERVICE POSITION

CAUTION C2490 C2491

C2491 C2490 In checking the board, make two capacitors discharge for electric shock prevention. (R: 800 /2W) MAIN board insulating sheet

LEAD WIRE SETTINGThe lead wire must not come in contact with the transformer and the heat sink.

Please band together so that a primary side cable cannot touch a power transformer and heat sink.

transformer

heat sink

10

STR-DA5300ES SECTION 2 GENERALGetting StartedThis section is extracted from instruction manual.

Description and location of parts (US and Canadian models)Front panel

To remove the coverPress PUSH. When you remove the cover, keep it out of reach from children.

Status of the POWER buttonOff The receiver is turned off (initial setting). Press POWER to turn the receiver on. You cannot turn the receiver on using the remote. Name A POWER Function Press to turn the receiver on or off. Name H SUR BACK DECODING I Display window Function Press to activate SB DECODING. The current status of the selected component or a list of selectable items appears here. On/Standby Press ?/1 on the remote to turn the receiver on or set it to the standby mode. When you press POWER on the receiver, the receiver will be turned off. Name N PHONES jack Function Connects to headphones.

B AUTO CAL MIC Connects to the jack supplied optimizer microphone for the Digital Cinema Auto Calibration function. C TONE MODE TONE Adjusts FRONT/ CENTER/ SURROUND/ SURROUND BACK BASS and TREBLE. Press TONE MODE repeatedly to select BASS or TREBLE, then turn TONE to adjust the level.

O SPEAKERS Switch to OFF, A, B, (OFF/A/B/A+B) A+B of the front speakers. P VIDEO 3 IN/ Connect to a portable PORTABLE AV audio/video component IN jacks such as a camcorder or video game. Q MULTI CHANNEL DECODING lamp R INPUT SELECTOR Lights up when multichannel audio signals are decoded. Turn to select the input source to play back. To select the input source for zone 2 or zone 3, press ZONE/ SELECT (qa) to select zone 2 or zone 3 first (ZONE 2 INPUT or ZONE 3 INPUT appears on the display), then turn INPUT SELECTOR to select the input source. Turn to adjust the volume level of all speakers at the same time.

J 2CH/A.DIRECT Press to select sound field. A.F.D. MOVIE MUSIC K ZONE/ POWER, SELECT Press SELECT repeatedly to select zone 2, zone 3 or main zone. Each time you press POWER, the output signals for the selected zone will be turned on or off. Press to select the audio/video input signal from the component connected to the DIGITAL MEDIA PORT adapter. Press to select input source from the component connected to the HDMI IN jack.

D MEMORY/ ENTER TUNING

Press to operate a tuner (FM/AM) and satellite TUNING MODE radio (XM/SIRIUS).

L DMPORT

E Remote sensor Receives signals from remote commander. F DIMMER Press repeatedly to adjust brightness of the display. Press repeatedly to select information displayed on the display.

M HDMI

G DISPLAY

S MASTER VOLUME

11

STR-DA5300ES

Rear panel

A DIGITAL INPUT/OUTPUT sectionOPTICAL IN/ Connect to a DVD OUT jacks player, Super Audio CD player, etc. The COAXIAL IN COAXIAL jack provides a better jacks quality sound. HDMI IN/ OUT* jacks Connect to a DVD player, Blu-ray Disc Player, or a satellite tuner. An image and the sound are output to TV or a projector.

D ANTENNA sectionFM ANTENNA Connects to the FM jack wire antenna (aerial) supplied with this receiver. AM ANTENNA jack XM jack Connects to the AM loop antenna (aerial) supplied with this receiver. Connects to the XM Mini Tuner and Home Dock (not supplied). Connects to a SiriusConnect Home tuner (not supplied).

H VIDEO/AUDIO INPUT/OUTPUT sectionAUDIO IN/ OUT jacks Connect to a VCR or a DVD player etc..

VIDEO IN/ OUT* jacks S VIDEO IN/ OUT* jacks AUDIO OUT jacks VIDEO OUT jack Connect to the component in zone 2 or zone 3.

B Control jack for Sony equipment and other external componentsIR REMOTE IN/OUT jacks TRIGGER OUT jacks Connect an IR repeater. Connect to interlock on/off of the power supply of other 12V TRIGGER compliant components, or the amplifier/receiver of zone 2 or zone 3. Connect to Sony TV, DVD player or VCR with CONTROL S jack.

SIRIUS jack

E COMPONENT VIDEO INPUT/ OUTPUT sectionY, PB/CB, PR/ CR IN/OUT* jacks Connect to a DVD player, TV, or a satellite tuner. EXT VIDEO IN Connects to the jack component when you want to watch in PIP (Picture in Picture) window.

CTRL S IN/ OUT jacks

F RS-232C portUsed for maintenance and service.

I SPEAKERS sectionConnects to speakers.

C DMPORTConnects to a Sony DIGITAL MEDIA PORT adapter.

G AUDIO INPUT/OUTPUT sectionAUDIO IN/ OUT jacks Connect to a tape deck or MD deck, etc.

* You can watch the selected input image when you connect the MONITOR VIDEO OUT jack to a TV. You can operate this receiver using a GUI (Graphical User Interface).

MULTI CHANNEL INPUT jacks

Connect to a Super Audio CD player or DVD player with an analog audio jack for 7.1 channel or 5.1 channel sound.

PRE OUT jacks Connect to an external power amplifier.

12

STR-DA5300ES

Remote commanderYou can use the supplied remote RM-AAL008 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate.

NameH Numeric buttons

FunctionPress to preset/tune to preset stations. select track numbers of the CD player, DVD player, Blu-ray Disc Player or MD deck. Press 0/10 to select track number 10. select channel numbers of the VCR or satellite tuner. After pressing TV (wk), press the numeric buttons to select the TV channels. Press to enter the value after selecting a channel, disc or track using the numeric buttons. Press to store a station during tuner operation. Press to display the menu to operate the receiver. Press V/v/B/b to select the menu items. to enter the selection. Then press

Name

Function

R DVD/ Press to display the menus of the DVD TOP MENU, player on the TV screen. Then use to perform a menu MENU V/v/B/b and operations. NIGHT MODE INPUT MODE Press AMP (5), then press NIGHT MODE to activate the NIGHT MODE function. Press AMP (5), then press INPUT MODE to select the input mode when the same components are connected to both digital and analog jacks. Press SHIFT (wj), then press SLEEP to activate the sleep timer function and the duration which the receiver turns off automatically.

RM-AAL008

I ENTER

SLEEP

MEMORY J AMP MENU K V/v/B/b L OPTIONS

TEST TONE Press SHIFT (wj), then press TEST TONE to output the test tone from each speaker. S MUTING T MASTER VOL +/ TV VOL +/ U DISC SKIP V RETURN/ EXIT O Press to turn off the sound temporarily. Press the button again to restore the sound. Press to adjust the volume level of all speakers at the same time. Press TV (wk), then press TV VOL +/ to adjust the volume level of the TV. Press to skip a disc when using a multi-disc changer. Press to return to the previous menu or exit the menu while the menu or on-screen guide of the VCR, DVD player, or satellite tuner is displayed on the TV screen. Press to select information displayed in the display window, TV screen of the VCR, satellite tuner, CD player, DVD player, Blu-ray Disc Player, or MD deck. Note In the SCREEN mode, press the button to display the menu on the TV screen. Press to clear a mistake when you press the incorrect numeric button. return to continuous playback, etc. of the satellite tuner or DVD player. Press to select track numbers over 10 of the VCR, satellite tuner, CD player or MD deck. channel numbers of the Digital CATV terminal. Press to enter direct tuning mode. Press to select sound field or to switch the audio of the selected input to analog signal without any adjustment. Press to select sound field. Press to light up the button. It changes the remote button function to activate the buttons with pink printing. Press to enable the TV operation. Press to set up the remote.

Press to display and select items from option menus for receiver and DVD player, Blu-ray Disc Player. Press to display and select items from the option menus for DVD player or Blu-ray Disc Player, etc. Press to display the menu to operate the audio/video components. Press SHIFT (wj), then press MENU to switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window).

TOOLS

M MENU SCREEN/ DSPL CONTROL

W DISPLAY

N CATEGORY Press to select the category for satellite +/ tuner.

O m/M a) x a) X a) H a) b) ./> a)

Press to operate the DVD player, Blu-ray Disc Player, CD player, MD deck, tape deck, or component connected to the DIGITAL MEDIA PORT adapter etc.

X CLEAR

CATEGORY Press to select the category mode for MODE satellite tuner. TUNING +/ Press to select station. P PRESET + b)/ Press to register FM/AM/satellite tuner stations or to select preset stations. Press TV (wk), then press TV CH+/ to operate the TV, satellite tuner, VCR, etc.

>10

NameA AV ?/1 (on/ standby)

FunctionPress to turn on or off the audio/video components that the remote is assigned to operate. If you press the ?/1 (B) at the same time, it will turn off the receiver and other Sony components (SYSTEM STANDBY). Note The function of the AV?/1 switch changes automatically each time you press the input button (C). Press to turn the receiver on or off. If ZONE 2 or ZONE 3 is selected, only the main receiver is turned on or off with this button. To turn off all components including an amplifier in zone 2 or zone 3, press ?/1 and AV?/1 (A) at the same time (SYSTEM STANDBY). Press one of the buttons to select the component you want to use. Press a pink-labeled button after pressing SHIFT (wj). When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony components. You can program the remote to control nonSony components following the steps in Programming the remote. Press to enable the zone 2 or zone 3 operation. Press to enable the receiver operation. Press to select sound field. Press to select sound field.

TV CH +/

D.TUNING Y 2CH/ A.DIRECT Z A.F.D. wj SHIFT

Q F1/F2

Press TV (wk), then press F1 or F2 to select a component to operate. HDD recorder F1: HDD F2: DVD player, Blu-ray Disc Player DVD/VHS combo player F1: DVD player, Blu-ray Disc Player F2: VHS Press AMP (5), then press MACRO 1 or MACRO 2 to set up the macro function. Press TV/INPUT and TV (wk) at the same time to select the input signal (TV input or video input). Press repeatedly to select the wide picture mode. Press SHIFT (wj), then press PIP to switch the image of the PIP (Picture in Picture) window. The image will be changed as follows. EXT VIDEO t ZONE 2 VIDEO t OFF. You can swap the position of the main screen and the PIP window (swap) by pressing the (qa). You can also move the window position using V/v/B/b (qa). Note The HDMI video signals are not output while the PIP window is displayed.

B ?/1 (on/ standby)

MACRO1, MACRO2 TV/INPUT

wk TV wl RM SET UPa)

WIDE PIP

See the table for information on the buttons that you can use to control each component. b) The tactile dot is attached to these buttons (H, PRESET+). Use as a mark of operation.

C Input buttons

NotesSome functions explained in this section may not work depending on the model. The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

D ZONE 2 ZONE 3 E AMP F MUSIC G MOVIE

RESOLUTION Press SHIFT (wj), then press RESOLUTION repeatedly to change the resolution of signals output from the HDMI OUT or COMPONENT VIDEO MONITOR OUT jack.

13

STR-DA5300ES

RM-AAU016This remote can only be used to operate the receiver. You can control the main functions of the receiver with simple operations using this remote.

NameE OPTIONS F MENU G DMPORT

FunctionPress to display and select items from option menus. Press to display the menu to operate the receiver. Press to operate the component connected to the DIGITAL MEDIA PORT adapter. Starts play. Stops play. Skips tracks. Press to select the input source to play back.

N x ./> H INPUT SELECTOR

I MASTER Press to adjust the volume level. VOLUME +/ J MUTING Press to turn off the sound temporarily. Press the button again to restore the sound. Press to return to the previous menu or exit the menu. Press to select information displayed in the display window. Note In the SCREEN mode, press the button to display the menu on the TV screen. Press PIP to switch the image of the PIP (Picture in Picture) window. The image will be changed as follows. EXT VIDEO t ZONE 2 VIDEO t OFF. You can swap the position of the main screen and the PIP window (swap) by pressing the (4). You can also move the window position using V/v/B/b (4). Note The HDMI video signals are not output while the PIP window is displayed.

K RETURN/ EXIT L DISPLAY

M PIP

NameA ?/1 (on/ standby) B 2CH/ A.DIRECT A.F.D. MOVIE MUSIC C SCREEN/ DSPL CONTROL

FunctionPress to turn a receiver on or off. Press to select sound field.

Press to switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window). After pressing SCREEN/DSPL CONTROL (3), press V/v/B/ b to select the menu item. Then press to enter the selection.

D V/v/B/b

14


Getting Started

Description and location of parts (AEP, Russian, Ukrainian, UK and Chinese models)Front panel

To remove the coverPress PUSH. When you remove the cover, keep it out of reach from children.

Status of the POWER buttonOff The receiver is turned off (initial setting). Press POWER to turn the receiver on. You cannot turn the receiver on using the remote. Name A POWER Function Press to turn the receiver on or off. Name H SUR BACK DECODING I Display window Function Press to activate SB DECODING. The current status of the selected component or a list of selectable items appears here. On/Standby Press ?/1 on the remote to turn the receiver on or set it to the standby mode. When you press POWER on the receiver, the receiver will be turned off. Name N PHONES jack Function Connects to headphones.

B AUTO CAL MIC Connects to the jack supplied optimizer microphone for the Digital Cinema Auto Calibration function. C TONE MODE TONE Adjusts FRONT/ CENTER/ SURROUND/ SURROUND BACK BASS and TREBLE. Press TONE MODE repeatedly to select BASS or TREBLE, then turn TONE to adjust the level. Press to operate a tuner (FM/AM).

O SPEAKERS Switch to OFF, A, B, (OFF/A/B/A+B) A+B of the front speakers. P VIDEO 3 IN/ Connect to a portable PORTABLE AV audio/video component IN jacks such as a camcorder or video game. Q MULTI CHANNEL DECODING lamp R INPUT SELECTOR Lights up when multichannel audio signals are decoded. Turn to select the input source to play back. To select the input source for zone 2 or zone 3, press ZONE/ SELECT (qa) to select zone 2 or zone 3 first (ZONE 2 INPUT or ZONE 3 INPUT appears on the display), then turn INPUT SELECTOR to select the input source. Turn to adjust the volume level of all speakers at the same time.

J 2CH/A.DIRECT Press to select sound field. A.F.D. MOVIE MUSIC K ZONE/ POWER, SELECT Press SELECT repeatedly to select zone 2, zone 3 or main zone. Each time you press POWER, the output signals for the selected zone will be turned on or off. Press to select the audio/video input signal from the component connected to the DIGITAL MEDIA PORT adapter. Press to select input source from the component connected to the HDMI IN jack.

D MEMORY/ ENTER TUNING MODE TUNING

L DMPORT

E Remote sensor Receives signals from remote commander. F DIMMER Press repeatedly to adjust brightness of the display. Press repeatedly to select information displayed on the display. M HDMI

G DISPLAY

S MASTER VOLUME

15

STR-DA5300ES

Rear panel

A DIGITAL INPUT/OUTPUT sectionOPTICAL IN/ Connect to a DVD OUT jacks player, Super Audio CD player, etc. The COAXIAL IN COAXIAL jack provides a better jacks quality sound. HDMI IN/ OUT* jacks Connect to a DVD player, Blu-ray Disc Player, or a satellite tuner. An image and the sound are output to TV or a projector.

D COMPONENT VIDEO INPUT/ OUTPUT sectionY, PB/CB, PR/ CR IN/OUT* jacks Connect to a DVD player, TV, or a satellite tuner.

H VIDEO/AUDIO INPUT/OUTPUT sectionAUDIO IN/ OUT jacks Connect to a VCR or a DVD player etc..

E ANTENNA sectionFM ANTENNA Connects to the FM jack wire antenna (aerial) supplied with this receiver. AM ANTENNA jack Connects to the AM loop antenna (aerial) supplied with this receiver.

VIDEO IN/ OUT* jacks S VIDEO IN/ OUT* jacks AUDIO OUT jacks VIDEO OUT jack Connect to the component in zone 2 or zone 3.

B Control jack for Sony equipment and other external componentsIR REMOTE IN/OUT jacks TRIGGER OUT jacks Connect an IR repeater. Connect to interlock on/off of the power supply of other 12V TRIGGER compliant components, or the amplifier/receiver of zone 2 or zone 3. Connect to Sony TV, DVD player or VCR with CONTROL S jack.

F RS-232C portUsed for maintenance and service. EXT VIDEO IN Connects to the jack component when you want to watch in PIP (Picture in Picture) window.

G AUDIO INPUT/OUTPUT sectionAUDIO IN/ OUT jacks Connect to a tape deck or MD deck, etc.

CTRL S IN/ OUT jacks

I SPEAKERS sectionConnects to speakers.

C DMPORTConnects to a Sony DIGITAL MEDIA PORT adapter.

MULTI CHANNEL INPUT jacks

Connect to a Super Audio CD player or DVD player with an analog audio jack for 7.1 channel or 5.1 channel sound.

PRE OUT jacks Connect to an external power amplifier.

* You can watch the selected input image when you connect the MONITOR VIDEO OUT jack to a TV. You can operate this receiver using a GUI (Graphical User Interface).

16

STR-DA5300ES

Remote commanderYou can use the supplied remote RM-AAL009 to operate the receiver and to control the Sony audio/video components that the remote is assigned to operate.

NameG MOVIE H Numeric buttons

FunctionPress to select sound field. Press to preset/tune to preset stations. select track numbers of the CD player, DVD player, Blu-ray Disc Player or MD deck. Press 0/10 to select track number 10. select channel numbers of the VCR or satellite tuner. After pressing TV (wk), press the numeric buttons to select the TV channels. Press to enter the value after selecting a channel, disc or track using the numeric buttons. Press to store a station during tuner operation. Press to display the menu to operate the receiver. Press V/v/B/b to select the menu items. Then press to enter the selection.

Name

Function

R DVD/ Press to display the menus of the DVD TOP MENU, player on the TV screen. Then use MENU V/v/B/b and to perform a menu operations. NIGHT MODE INPUT MODE Press AMP (5), then press NIGHT MODE to activate the NIGHT MODE function. Press AMP (5), then press INPUT MODE to select the input mode when the same components are connected to both digital and analog jacks. Press SHIFT (wj), then press SLEEP to activate the sleep timer function and the duration which the receiver turns off.

RM-AAL009

I ENTER

SLEEP

MEMORY J AMP MENU K V/v/B/b L OPTIONS

TEST TONE Press SHIFT (wj), then press TEST TONE to output the test tone from each speaker. S MUTING Press to turn off the sound temporarily. Press the button again to restore the sound. Press to adjust the volume level of all speakers at the same time. Press TV (wk), then press TV VOL +/ to adjust the volume level of the TV. Press to skip a disc when using a multi-disc changer. Press to return to the previous menu or exit the menu while the menu or on-screen menu or on-screen guide of the VCR, DVD player, or satellite tuner is displayed displayed on the TV screen. Press to select information displayed in the display window, TV screen of the VCR, satellite tuner, CD player, DVD player, Blu-ray Disc Player, or MD deck. Note In the SCREEN mode, press the button to display the menu on the TV screen. X CLEAR Press to clear a mistake when you press the incorrect numeric button. return to continuous playback, etc. of the satellite tuner or DVD player. Press to select track numbers over 10 of the VCR, satellite tuner, CD player or MD deck. channel numbers of the Digital CATV terminal. Press to enter direct tuning mode. Press to select sound field or to switch the audio of the selected input to analog signal without any adjustment. Press to select sound field. Press to light up the button. It changes the remote button function to activate the buttons with pink printing. Press to enable the TV operation. Press to set up the remote.

T MASTER VOL +/ TV VOL +/ U DISC SKIP V RETURN/ EXIT O

Press to display and select items from option menus for receiver and DVD player, Blu-ray Disc Player. Press to display and select items from the option menus for DVD player or Blu-ray Disc Player, etc. Press to display the menu to operate the audio/video components. Press SHIFT (wj), then press MENU to switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window). Press to select the album. Press to operate the DVD player, Blu-ray Disc Player, CD player, MD deck, tape deck, or component connected to the DIGITAL MEDIA PORT adapter etc.

TOOLS

M MENU SCREEN/ DSPL CONTROL

W DISPLAY

N B/b O m/M x a) X a) H a) b) ./> a)

TUNING +/ Press to select station. P PRESET + b)/ TV CH +/ Q F1/F2 Press to register FM/AM Radio station or to select preset stations. Press TV (wk), then press TV CH+/ to operate the TV, satellite tuner, VCR, etc. Press TV (wk), then press F1 or F2 to select a component to operate. HDD recorder F1: HDD F2: DVD player, Blu-ray Disc Player DVD/VHS combo player F1: DVD player, Blu-ray Disc Player F2: VHS Press AMP (5), then press MACRO 1 or MACRO 2 to set up the macro function. Press TV/INPUT and TV (wk) at the same time to select the input signal (TV input or video input). Press repeatedly to select the wide picture mode. Press SHIFT (wj), then press PIP to switch the image of the PIP (Picture in Picture) window. The image will be changed as follows. EXT VIDEO t ZONE 2 VIDEO t OFF. You can swap the position of the main screen and the PIP window (swap) by pressing the (qa). You can expand or shrink the window using V/v (qa). You can also change the windows position using B/b (qa). Note The HDMI video signals are not output while the PIP window is displayed. wk TV wl RM SET UPa)

>10

NameA AV ?/1 (on/ standby)

FunctionPress to turn on or off the audio/video components that the remote is assigned to operate. If you press the ?/1 (B) at the same time, it will turn off the receiver and other Sony components (SYSTEM STANDBY). Note The function of the AV?/1 switch changes automatically each time you press the input button (C). Press to turn the receiver on or off. If ZONE 2 or ZONE 3 is selected, only the main receiver is turned on or off with this button. To turn off all components including an amplifier in zone 2 or zone 3, press ?/1 and AV?/1 (A) at the same time (SYSTEM STANDBY).

D.TUNING Y 2CH/ A.DIRECT Z A.F.D. wj SHIFT

B ?/1 (on/ standby)

MACRO1, MACRO2 TV/INPUT

WIDE PIP

Saving the power in standby mode.When HDMI Control and RS-232C Control are set to OFF. C Input buttons Press one of the buttons to select the component you want to use. Press a pink-labeled button after pressing SHIFT (wj). When you press any of the input buttons, the receiver turns on. The buttons are factory assigned to control Sony components. You can program the remote to control non-Sony components following the steps in Programming the remote. Press to enable the zone 2 or zone 3 operation. Press to enable the receiver operation. Press to select sound field.

See the table for information on the buttons that you can use to control each component. b) The tactile dot is attached to these buttons (H, PRESET+). Use as a mark of operation.

NotesSome functions explained in this section may not work depending on the model. The above explanation is intended to serve as an example only. Therefore, depending on the component, the above operation may not be possible or may operate differently than described.

D ZONE 2 ZONE 3 E AMP F MUSIC

RESOLUTION Press SHIFT (wj), then press RESOLUTION repeatedly to change the resolution of signals output from the HDMI OUT or COMPONENT VIDEO MONITOR OUT jack.

17

STR-DA5300ES

RM-AAU016This remote can only be used to operate the receiver. You can control the main functions of the receiver with simple operations using this remote.

NameE OPTIONS F MENU G DMPORT

FunctionPress to display and select items from option menus. Press to display the menu to operate the receiver. Press to operate the component connected to the DIGITAL MEDIA PORT adapter. Starts play. Stops play. Skips tracks. Press to select the input source to play back.

N x ./> H INPUT SELECTOR

I MASTER Press to adjust the volume level. VOLUME +/ J MUTING Press to turn off the sound temporarily. Press the button again to restore the sound. Press to return to the previous menu or exit the menu. Press to select information displayed in the display window. Note In the SCREEN mode, press the button to display the menu on the TV screen. Press PIP to switch the image of the PIP (Picture in Picture) window. The image will be changed as follows. EXT VIDEO t ZONE 2 VIDEO t OFF. You can swap the position of the main screen and the PIP window (swap) by pressing the (4). You can expand or shrink the window using V/v (4). You can also change the windows position using B/b (4). Note The HDMI video signals are not output while the PIP window is displayed.

K RETURN/ EXIT L DISPLAY

M PIP

NameA ?/1 (on/ standby) B 2CH/ A.DIRECT A.F.D. MOVIE MUSIC C SCREEN/ DSPL CONTROL

FunctionPress to turn a receiver on or off. Press to select sound field.

Press to switch the display mode of the menu between SCREEN (to display the menu on the TV screen) and DSPL (to display the menu in the display window). After pressing SCREEN/DSPL CONTROL (3), press V/v/B/ b to select the menu item. Then press to enter the selection.

D V/v/B/b

18

STR-DA5300ES SECTION 3 DISASSEMBLY This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOWNote 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.

SET

3-2. CASE (Page 20)

3-3. SP-TM BOARD, TUNER (FM/AM) (Page 20)

3-4. D-CONNECT BOARD, DSP BOARD, DIGITAL BOARD, CIS BOARD AND CONTROL BOARD (Page 21)

3-5. D-VIDEO BOARD (Page 21)

3-7. S-VIDEO BOARD AND A-VIDEO BOARD (Page 22)

3-6. FRONT PANEL SECTION (Page 22)

3-8. FLI-1.8REG BOARD AND ANALOG BOARD (Page 23)

3-10. HEART SINK SECTION (Page 25) 3-9. POWER TRANSFORMER (T001), E-VOL BOARD AND MAIN BOARD (Page 24)

19


Note: Follow the disassembly procedure in the numerical order given.

3-2. CASE1 two screws (BVST4 8 (for black), BVTT4 8 (for silver)) 3 flat head screw (TP) 2 two flat head screws (TP)

5 case 4

4

1 two screws (BVST4 8 (for black), BVTT4 8 (for silver))

3-3. SP-TM BOARD, TUNER (FM/AM)4 tuner (FM/AM) 1 clamp

8 SP-TM board 1 clamp 6 3 two screws (BVTT2.6 6) 5 two screws (BV/ring)

7 four connectors (CX4101, CX4102 CX4103, CX4104) 1 clamp

2 wire (flat type) (9 core) (US and Canadian models), wire (flat type) (11 core) (AEP, Russian, Ukrainian, UK and Chinese models) (tuner (FM/AM))

20


3-4. D-CONNECT BOARD, DSP BOARD, DIGITAL BOARD, CIS BOARD AND CONTROL BOARDwa CONTROL board qh CIS board

qk three connectors (CN2012, CN2013, CN2014) w; connector (CN2002) qg 7 connector (CN2203) ql qj screw (BVTP3 8) qf two screws (BVTP3 8) 3 eight screws (BVTP3 8) 2 D-CONNECT board 1 six connectors (CN2401, CN2402, CN2403, CN2404, CN2405, CN2406) 9 connector (CN5001)

8 four screws (BVTP3 8) q; DSP board

4 two screws (BVTP3 8)

6 two connectors (CN2204, CN2207) qd DIGITAL board qs bracket (AC) qa two screws (BVTP3 8) 5

3-5. D-VIDEO BOARD3 screw (BVTP3 8) 7 bracket (HDMI)

8 D-VIDEO board

(AEP, Russian, Ukrainian, UK and Chinese models) 1 two clamps6 screw (BVTP3 8)

(US and Canadian models)1 clamp 4 two screws (BV3)

5 seven screws (B3 6)

2 five connectors (CN3509, CN3523, CN3605, CN3611, CN3902)

21

STR-DA5300ES

3-6. FRONT PANEL SECTION3 connector (CNP53) 1 two clamps 4 connector (CN606) 5 connector (CN6904)

8

2 clamp 7 two screws (BVTP3 8) 6 five screws (BVTP3 8) 9 front panel section

3-7. S-VIDEO BOARD AND A-VIDEO BOARD

4 S-VIDEO board 5 two connectors (CN6518, CN6519) 3 four screws (BVTP3 8) 1 connector (CN6904) 6 seven screws (BVTP3 8) 2 wire (flat type) (21 core) (S-VIDEO board (CN6903), A-VIDEO board (CN6509))

7 screw (BVTP3 8)

8 A-VIDEO board

22


3-8. FLI-1.8REG BOARD AND ANALOG BOARD

qa screw (BVTP3 8)

qd wire (flat type) (9 core) (US and Canadian models) (CN609), wire (flat type) (11 core) (AEP, Russian, Ukrainian, UK and Chinese models) (CN603) qf ANALOG board

qs bracket (side) 2 FLI-1.8REG board 4 bracket (WB) 5 connector (CN608) 3 two screws (BVTP3 8) 7 two connectors (CN601, CN1003)

q; six screws (BVTP3 8) 1 screws (BVTP3 8)

9 screw (B3 6)

(US and Canadian models)q; 8 connector (CN727)

6 connector (CN606)

23

STR-DA5300ES

3-9. POWER TRANS FORMER (T001), E-VOL BOARD AND MAIN BOARD

9 CONNECTOR 1 board 7 CONNECTOR 2 board 6 two connectors (CN1205, CN1206) qg bracket (SS) qh E-VOL board qf two screws (BVTP3 8) qg bracket (SS) 8 two connectors (CN1207, CN1209) qs two screws (BVTP3 8)

qd two connectors (CN1203, CN1204) qa wire (E-VOL board (CN1208), MAIN board (CN1206)) 2 connector (CNP02) 4 four screws (BVTT4 8) 1 connector (CN1402) wa five screws (BVTP3 8)

q; wire (E-VOL board (CN1209), MAIN board (CN1205))

ws two wires (CN1001, CN1004)

wd MAIN board

5 power transformer (T001) 3 two connectors (CN1403, CN1408)

w; three screws (BV/ring)

ql four screws (BVTP3 8)

qk feeder fixed screw

qj two screws (supllied with J1499)

24

STR-DA5300ES

3-10. HEAT SINK SECTION6 three screws (BVTP3 8) 6 four screws (BVTP3 8)

2 CONNECTOR 2 board

1 two connectors (CN1205, CN1206) 4 CONNECTOR 1 board

3 two connectors (CN1207, CN1209)

7 heart sink section

5 connector (CN1405)

25

STR-DA5300ES SECTION 4 TEST MODEMEMORY CLEARING MODEAll preset contents are cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. Procedure: 1. While pressing the [TONE MODE] and [DMPORT] buttons, press the [POWER] button to turn on the main power. 2. The message MEMORY CLEARING*** appears and the memories are reset to the default values. 3. When done, the message MEMORY CLEARED* appears.

XM FACTORY TEST MODE (US and Canadian models only)Mode to confirm operation of XM. Doing display of ID of XM antenna and output of audio signal that XM antenna generates, it is confirmed that there are no problems in the communication of the XM antenna and the tranmission of the audio signal. Procedure: 1. The XM antenna was connected, while pressing the [TUNING MODE] and [MOVIE] buttons, press the [POWER] button to turn on the main power. 2. Whenever the [DISPLAY] button is pressed, the output of the audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1 kHz L and 1 kHz R are switched.

FLUORESCENT INDICATOR TUBE PATTERN CHECK MODEAll fluorescent segments are tested. When this test is activated, all segments turn on at the same time, then each segment turns on one after another. Procedure: 1. While pressing the [MOVIE] and [DMPORT] buttons, press the [POWER] button to turn on the main power. 2. All segments and all LEDs turn on.

SIRIUS FACTORY TEST MODE (US and Canadian models only)Mode to confirm operation of SIRIUS. Doing display of ID of SIRIUS antenna and output of audio signal that SIRIUS antenna generates, it is confirmed that there are no problems in the communication of the SIRIUS antenna and the transmission of the audio signal. Procedure: 1. The SIRIUS antenna was connected, while pressing the [TUNING MODE] and [A.F.D.] buttons, press the [POWER] button to turn on the main power. 2. Whenever the [DISPLAY] button is pressed, the output of the audio signal of 1 kHz L/R, 20 Hz L/R, 5 kHz L/R, muting, 1 kHz L and 1 kHz R are switched.

SOUND FIELD CLEAR MODEThe preset sound field is cleared when this mode is activated. Use this mode before returning the product to clients upon completion of repair. Procedure: 1. While pressing the [MUSIC] button, press the [POWER] button to turn on the main power. 2. The message S. F. Initialize appears and initialization is performed.

DIGITAL MEDIA PORT TESTProcedure: 1. Connect the DMPORT check jig (P/N: J-2501-309-A) with the DMPORT jack (CN6505) on the A-VIDEO board. 2. While pressing the [A.F.D.] and [DMPORT] buttons, press the [POWER] button to turn on the main power. 3. The message DMPORT OK. appears on the fluorescent indicator tube and enter the digital media port test mode (Confirmation of communication line). When NO DETECT, UART NG and UART TO are displayed on the fluorescent indicator tube, confirm the connection of the DMPORT check jig, and enter the mode again. Each time the > button on the remote commander is pressed, the connect check and adaptor version check are switched. Press the . button on the remote commander, connected confirmation of the DMPORT check jig is done again. 4. To a pin-jack of the DMPORT check jig input information relevant to audio signal (sine-wave 1.0 Vrms) and composite video signal (white 100% 1.0 Vp-p, color bar, etc.). 5. Confirm the output of speakers and monitor TV (Confirmation of analog signal). 6. To exit from this mode, press the x button on the remote commander.J001 color pattern generator AF oscillator MAIN board TM4002 A-VIDEO board CN6505 DMPORT check jig (Part No.: J-2501-309-A) A-VIDEO board J6203 TV monitor set FL/FR speaker

TUNER AM STEP CHANGE (9 kHz/10 kHz) MODE (US and Canadian models only)Either the 9 kHz step or 10 kHz step can be selected for the AM channel step. Procedure: 1. Press the [POWER] button to turn on the main power. 2. Turn the [INPUT SELECTOR] dial to select the AM. 3. Press the [POWER] button to turn off the main power. 4. While pressing the [TUNING MODE] button, press the [POWER] button to turn on the main power. 5. Either the message AM 9kHz Step or AM 10kHz Step appears, select the desired step.

COMMAND MODE CHANGE MODEThe command mode of the remote-commander which this set receives can be changed. Procedure: 1. While pressing the [2CH/A. DIRECT] button, press the [POWER] button to turn on the main power. 2. Either the message COMMAND MODE [AV1] or COMMAND MODE [AV2] appears. Select the desired mode.

SF LOCK ON/OFF CHANGE MODEProcedure: 1. While pressing the [MUSIC] and [DMPORT] buttons, press the [POWER] button to turn on the main power. 2. Either the message SF LOCK [OFF] or SF LOCK [ON] appears.

26

STR-DA5300ES

HISTORY MODEThe state that the set is used is memorized. Procedure: 1. While pressing the [MUSIC] and [MEMORY/ENTER] buttons, press the [POWER] button to turn on the power and HISTORY MODE is displayed. 2. Each time the M m key of remote commander is pressed, the item is switched in order as follows.Items Number of protector is generated Total use time Sound field setting Input when protect is detected Input mode setting Input mode under lick state Stream under input Channel information State of headphone Volume EQ setting value Display PRCT COUNT: XXX TTL_TIME: XXXXH XXM XXXXXXXXXXXXXXXX INPUT: XXXXXXXXXX INMODE: XXXXXXXXXXXX DSEL: XXXXXXXXXXXXXXX STREAM: XXXXXXX CONFIG:XXXXXXX HEAD PHONES: XXX VOL: XXXdB BASS: XXXdB TREB: XXXdB Lv FL/FR XXXX/XXXX Lv SL/SR XXXX/XXXX Lv CT/SW XXXX/XXXX Lv BL/BR XXXX/XXXX TTL_P_ON: XXXXH XXM

Level collection value each channel Total time of power on

27

STR-DA5300ES

SPECIAL MENU MODEProcedure: 1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in order, the message MENU SPECIALIZED! appears. 2. Press the M m button of the remote commander, the message > appears. 3. Press the , button of the remote commander, the item is appears. 4. Each time the M m button of the remote commander is pressed, the item is switched in order as follows. Some items can change the content. Display the cursor by pressing the , button of the remote commander, and changing the content by pressing the M m button of the remote commander, and fix the content by pressing the < button of the remote commander when you want to change the content of the item. 5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE] button in order again, the message MENU SPECIALIZED OFF appears.Items Video factory menu Display Remark Menu mode to enter video calibration menu and DDR access check menu If the [ENTER] button of the remote commander is pressed, entering the menu, and operating two the following menu become possible Procedure: 1. DVD is selected by using [INPUT SELECTOR] dial. 2. Connect a color pattern generator to the COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) DVD/BD IN jack (J6002) on the AVIDEO board, DVD/BD VIDEO IN jack (J6201) on the A-VIDEO board, DVD/BD S VIDEO IN jack (J6901) on the S-VIDEO board and EXT VIDEO IN jack (J6904). 3. Input 100% color bars signal from the color pattern generator. 4. Menu that measures individual difference of hardness by automatic operation in pressing the [ENTER] button of the remote commander, and corrects reference value. In a measurement once, only one of NTSC/PAL/HD can be measured Check XXXX V-IN at display: Video signal necessary for the measurement while measuring it last time was not detected and it became an error Confirm the input of the video of the terminal connection etc. , and DDR access check (Video factory menu) Auto cal mic test DDR CHECK [XX] sec SPEAKER OUT [XXXXX] measure the [ENTER] button of the remote commander again pressing XX: Time to do access check on DDR (for design evaluation) XXXXX: Selection of speaker output audio [SOURCE]: nomally mode, [MIC]: mode that output audio from mic from speaker **: 20 to FE, X: character Each time DISPLAY button to change as follows all on t test pattern 1 t test pattern 2 t all off t all on XXX: ON or OFF XX: OK or NG OK: success access SRAM, NG: fail access to SRAM

Video calibration (Video factory menu)

V.CALIBRATION START?

FL display fonts test FL display test HDCP key read DSP SRAM check

FL FONT [0x ** = X] ALL ON HDCP KEY READ [XXX] [ENTER] button of the remote r commander SRAM1 [XX] SRAM2 [XX] FAROUDJA UPDATE [XXX] ##### *** vX. XX @@@@

FAROUDJA update Model version display

Video Ucom version display FAROUDJA version display GUI CG-ROM version display DSP Ucom version display DSP serial flash version display DSP parallel flash version display DSP halt DSP RAM

Video Ucom Ver X. XX FAROUDJA Ver X. XX GUI CGROM Ver X. XX DSP Ucom Ver X. XX DSP SFLASH Ver X. XX DSP PFLASH Ver X. XX DSP HALT [XXX] [*****]=XXXXXXXX

XXX: ON or OFF #####: Model ***: Destination X.XX: System controller software version @@@@: Sum value of flash memory in the system controller X.XX: Video system controller software version X.XX: Video Processor software version X.XX: CG-ROM software version X.XX: DSP controller version X.XX: Serial flash software version X.XX: DSP parallel flash version XXX: ON or OFF Mode that refers to internal RAM of DSP (for design evaluation)

28

STR-DA5300ES

Items Super reset

Display SUPER RESET [XXX]

RAM watch menu EERROM debug Protector on/off Model/destination change Audio swap Decoder select Volume value display (FL/FR) Volume value display (SL/SR) Volume value display (CT/SW) Volume value display (SBL/SBR)

XXX EEPROM [****] [XX] PROTECTOR ON/OFF [XXX] MODEL [##### * * * *] X X SWAP [XXXXXXXXXXX] DECODER SEL [XXXX] FL**** FR XXXX SL**** SR XXXX CT**** SW XXXX SBL**** SBR XXXX

DAC mute information disclosure 1 DAC MUTE U XXXXXXXX DAC mute information disclosure 2 DAC MUTE L XXXXXXXX 2nd volume value display FL display duty change DMPORT debug Bus overflow debug HA link (receive) Bus overflow debug HA link (transmit) Bus overflow debug DMPORT 2nd VOLUME XXX DARK OUT DUTY [XXX%] DMP KEY DEBUG [XXX] OVERFLOW HAL R [XX] OVERFLOW HAL S [XX] OVERFLOW CLA [XX]

Remark Not used for the servicing If super reset is performed, up convert signal level adjustment will also be initialized When EEPROM initialization is required, perform the memory clearing mode XXX: For monitor of various internal RAM (for design evaluation) ****: EEPROM address, XX: EEPROM data XXX: ON or OFF #####: Model, ****: Destination, XX: At or fx Switching with M m button of the remote commander XXXX: AUTO, LEGACY, DDPLUS, TRUEHD, DTSEXP, MP3SUR (for debug) ****: Front L-ch volume value, XXXX: Front R-ch volume value ****: Surround L-ch volume value, XXXX: Surround R-ch volume value ****: Center volume value, XXXX: Sub woofer volume value ****: Surround back L-ch volume value, XXXX: Surround back R-ch volume value Display of module information to demand muting in system controller (for design evaluation) Display of module information to demand muting in system controller (for design evaluation) XXX: 2nd room volume value (00 to ) XXX: Duty value of FL display (0% to 100%) XXX: ON or OFF (for debug) XX: Counter of overflow receive buffer XX: Counter of overflow transmit buffer XX: Counter of overflow CLA transmit buffer

29

STR-DA5300ES SECTION 5 ELECTRICAL ADJUSTMENTSBIAS ALIGNMENT ADJUSTMENTNote: After 10 minutes or more have passed since the power supply was turned on, this adjustment is done.

Connection:digital voltmeter

CN1561 (CN1611, CN1761, CN1861) pin 1, CN1561 (CN1761, CN1861) pin 3 CN1561 (CN1611, CN1761, CN1861) pin 2, CN1561 (CN1761, CN1861) pin 4Note: Pin 3, 4 of CN1611 are open.

+

Procedure: 1. Connect a digital voltmeter to the CN1561 (CN1611, CN1761, CN1861). 2. Press the [POWER] button to turn on the main power. 3. Adjust the RV1501 (RV1551, RV1601, RV1701, RV1751, RV1801, RV1851) so that the digital voltmeter reading is 5 mV to 20 mV. Adjustment and Connection Location: BIAS Board (Conductor Side)

Adjustment hole Adjustment hole Adjustment hole for RV1801 for RV1851 for RV1601 (SBL) (SBR) (CENTER)

Adjustment hole Adjustment hole Adjustment hole for RV1501 for RV1551 for RV1701 (F-L) (F-R) (SUR-L)

Adjustment hole for RV1751 (SUR-R)

PROTECTOR (SB) Board (Component Side) CN1861 4 1

PROTECTOR (F-C) Board (Component Side) CN1611 4 1 CN1561 4 1

PROTECTOR (SURR) Board (Component Side) CN1761 4 1

30


VIDEO CALIBRATION ADJUSTMENTAdjustment to decide the standard of the video input signal.Note: After replacing D-VIDEO board, or after SUPER RESET of the special menu mode is executed, perform this adjustment.

1-2. S Video signal Checking S Video Output S-Y Signal Check point Specification DVD standard disc color bars (100%) S VIDEO OUT (S-Y) terminal (75 terminated) 1.00 0.03 Vp-p

2. Video calibration adjustment 2-1. ConnectionS-VIDEO board EXT VIDEO IN jack (J6904) color pattern generator or Blu-ray Disc player A-VIDEO board VIDEO 1 OUT jack (J6205) TV monitor A-VIDEO board MONITOR VIDEO OUT jack (J6206)

1. Adjustment jig The color pattern generator that can output 100% in NTSC/PAL/ HD color bar signal to the component, the composite and the S video at the same time is necessary for the adjustment. When there is no color pattern generator, it is possible to substitute it by the Blu-ray Disc player that can output the component terminal and the video terminal at the same time (Substitution model name example: BDP-S350). However, please do the following signal output confirmation with the oscilloscope beforehand when substituting it with the Blu-ray Disc player. 1-1. Component signal Checking Component Video Output Y Signal Check point Specification DVD standard disc color bars (100%) COMPONENT VIDEO OUT (Y) terminal (75 terminated) 1.00 0.03 Vp-p

set

1.00 0.03 Vp-p

A-VIDEO board COMPONENT VIDEO ASSIGNABLE (INPUT ONLY) DVD/BD IN jack (J6002) A-VIDEO board DVD/BD VIDEO IN jack (J6201) S-VIDEO board DVD/BD S VIDEO IN jack (J6901)

Checking S Video Output S-C Signal Check point Specification DVD standard disc color bars (100%) S VIDEO OUT (S-C) terminal (75 terminated) 286 30 m Vp-p 2-2. Procedure for color pattern generator 1. It connects of step 2-1, and the turn on the main power. 2. DVD is selected by using [INPUT SELECTOR] dial. 3. Input NTSC color bars signal from the color pattern generator. 4. Press the [POWER] button to turn off the main power. 5. While pressing the [MEMORY/ENTER], [MUSIC] and [DMPORT] buttons, press the [POWER] button to turn on the main power. When correctly entering the test mode V.CAL COMPLETE N:P:H is displayed (keeps pressing three buttons until the message appears). 6. The NTSC signal adjustment is begun when press the cross (center of cursor) button of remote commander, and the display changes from NTSC:MW ----- to NTSC:MW OK C S V E little by little. Finally, the display returns to the display of V.CAL COMPLETE N:P:H. 7. Input PAL color bars signal from the color pattern generator. 8. Perform step 6 to 7 for the PAL signal adjustment. 9. Input HD color bars signal (720p or 1080i) from the color pattern generator. 10. Perform step 6 to 7 for the HD signal adjustment. 11. The turn off the main power.

286 30 mVp-p

1.00 0.03 Vp-p

1-3. Composite signal Video level confirmation Signal DVD standard disc color bars (100%) LINE OUT (VIDEO) terminal (75 terminated) Specification 1.00 0.03 Vp-p Check point

Checking Component Video Output B-Y Signal Check point Specification DVD standard disc color bars (100%) COMPONENT VIDEO OUT (PB/CB) terminal (75 terminated) 0.70 0.03 Vp-p

1.00 0.03 Vp-p

0.70 0.03 Vp-p

2-3. Procedure for Blu-ray Disc player 1. It connects of step 2-1, and the turn on the main power of set and Blu-ray Disc player. 2. DVD is selected by using [INPUT SELECTOR] dial. 3. Press the OPEN/CLOSE button of the Blu-ray Disc player, and DVD test disc HLX-504 (Part No. J-6090-088-A) or HLX-513 (Part No. J-2501-305-A) is insert. The disc playback automatically becomes start Main Menu is display. 4. 1.Color Bar 100% of 1.Video Signal is reproduced, and 100% in the color bar is displayed in the TV monitor, playing the Blu-ray Disc player is pause playback. 5. Press the [POWER] button to turn off the main power of the set. 6. While pressing the [MEMORY/ENTER], [MUSIC] and [DMPORT] buttons, press the [POWER] button to turn on the main power of the set. When correctly entering the test mode V.CAL COMPLETE N:P:H is displayed (keeps pressing three buttons until the message appears). 7. The NTSC signal adjustment is begun when press the cross (center of cursor) button of remote commander, and the display changes from NTSC:MW ----- to NTSC:MW OK C S V E little by little. Finally, the display returns to the display of V.CAL COMPLETE N:P:H. 8. Press the OPEN/CLOSE button of the Blu-ray Disc player, and change to DVD test disc HLX-506 (Part No. J-6090077-A) or HLX-507 (Part No. J-6090-078-A). The disc playback automatically becomes start Main Menu is display. 9. 1.Color Bar 100% of 1.Video Signal is reproduced, and 100% in the color bar is displayed in the TV monitor, playing the Blu-ray Disc player is pause playback. 10. The PAL signal adjustment is begun when press the cross (center of cursor) button of remote commander. Finally, the display returns to the display of V.CAL COMPLETE N:P:H. 11. Press the OPEN/CLOSE button of the Blu-ray Disc player, and change to DVD test disc HLX-104 (Part No. J-6090199-A). The disc playback automatically becomes start Main Menu is display. 12. 59.94Hz, 1080i 1.Video Signal 1.Color Bar 100% is selected, and 100% in the color bar is displayed in the TV monitor, playing the Blu-ray Disc player is pause playback. 13. The video output of the Blu-ray Disc player is switched 1080i (The output from the component terminal of the Blu-ray Disc player becomes 1080i output). 14. The HD signal adjustment is begun when press the cross (center of cursor) button of remote commander. Finally, the display returns to the display of V.CAL COMPLETE N:P:H. 15. The turn off the main power.

Checking Component Video Output R-Y Signal Check point Specification DVD standard disc color bars (100%) COMPONENT VIDEO OUT (PR/CR) terminal (75 terminated) 0.70 0.03 Vp-p

0.70 0.03 Vp-p

STR-DA5300ES

31

31

STR-DA5300ES

FM AUTO STOP CHECKsignal generator set

Procedure: 1. Turn on the set. 2. Input the following signal from signal generator to FM antenna input directly. Carrier frequency: A = 87.5 MHz, B = 98 MHz, C = 108 MHz Deviation : 75 kHz Modulation : 1 kHz ANT input : 35 dBu (EMF)Note: Use 75 ohm coaxial cable to connect signal generator and the set. You cannot use video cable for checking. Use signal generator whose output impedance is 75 ohm.

3. Set to FM tuner function and scan the input FM signal with automatic scanning. 4. Confirm that input frequency of A, B and C are detected and automatic scanning stops. When the station signal is received in good condition, automatic scanning stops.

STR-DA5300ES

32

32

STR-DA5300ES SECTION 6 DIAGRAMS6-1. BLOCK DIAGRAM CONTROL Section A/D CONVERTER IC2217

Ver. 1.2

(Page 37)

1

HDMI_SPDIF

(Page 39) 6 (Page 37) 7

DATA SELECTOR IC2213 2 A0 3 B0 5 A1 6 B1 11 A2 10 B2 14 A3 13 B3 Y0 4 SI_B

ADFL R-CH

10 AINL SDOUT 4 12 AINR SD0

TV OPTICAL IN

OPTICAL RECEIVER IC2225 OPTICAL TRANSCEIVER IC2205 OPTICAL RECEIVER IC2204 OPTICAL RECEIVER IC2201 OPTICAL RECEIVER IC2202 OPTICAL RECEIVER IC2203 J2201 X2201 24.576MHz 14 D5 4 D0 1 3 2 15 D3 D1 D2 D4 DIGITAL OUT SWITCH IC2206 INPUT SELECTOR IC2207 Y 5

HDMI_ERROR 2 9 7 8 MCLK RST SCLK LRCK SD1

Y1 7

SI_C

MD/DAT OPTICAL OUT

(Page 37) 8

HDMI_BCK, HDMI_LRCK, HDMI_MCK

(Page 37) 36SD2

Y2 9

SI_D

SD3 DIGITAL AUDIO INTERFACE RECEIVER IC2208 1 RXOUT 10 RX6/UI 2 RX0 RDATA 21

Y3 12 S 1

SI_E

MD/DAT OPTICAL IN

DATA SELECTOR IC2214 2 A0 3 B0 5 A1 6 B1 DATA SELECTOR IC2212 Y0 4 SI_A

A0

A1

A2

VIDEO 1 OPTICAL IN

XMCK 27 8 RX4 5 RX3 RBCK 17 HDMI_BCK

Y1 7

11

10

9

9Y2 9 S 1

(Page 34)

DIGITAL ASSIGNABLE (INPUT ONLY)

SAT/CATV OPTICAL IN

(Page 38) 51

NON_LPCM

11 A2 10 B2

14 A3 13 B3 11 A2 10 B2 Y3 12 Y2 9

TAPE/CD-R OPTICAL IN

4 RX2

RLRCK 20

BCK LRCK DIR-ERR

HDMI_LRCK

29 XIN 28 XOUT 13 LPF

VIDEO 2 COAXIAL IN

DSEL0

DSEL1

DSEL2

DVD/BD COAXIAL IIN SA-CD/CD COAXIAL IIN

WAVE SHAPER IC2209

4

5

6

DATA DECODER IC2210

RMCK 16 AUDIO/VO 33

HDMI_MCK

5 A1 6 B1

S 1

Y1 7

MCK DIR_NONAU BUFFER IC2211 D/A MCK ERR ANA/DIGI

H_SEL1

H_SEL2

S-IN CLK

LAT OE

PLL CLOCK SELECT Q2201-2203,2207

36 37 38 40 39 34 41

VIDEO 3 IN/ PORTABLE AV IN DIGITAL (OPT)

OPTICAL RECEIVER IC707

2

3

14 11

12 13

RERR DO DI CL CE CKST XMODE

REQ 7 DSP_SEL 15 ANA/DIGI 1

10 (Page 35)

COM1-DAT COM1-CLK

(Page 37) (Page 39)

2 3

TU-L

V595_LAT V595_OE COM2_CLK COM2_DAT

TUNER (FM/AM) TUN_L TUN_R FM 75 COAXIAL ANTENNA AM R-CH 109 108 67 66 65 68 64 46 93 168

COM1-DAT COM1-CLK

H/XSEL1 H/XSEL2

CTL

11 (Page 43)

DIR_RERR DIR_DO

DIR_CE DIR_CKST DIR_XMODE

AD_RST

D595_LAT D595_OE

HDMI_ERROR

FSRATE1

TUN_DATA TUN_DO TUN_CLK TUN_CE TUNED RDS-DATA RDS-CLK ( AEP, Russian, Ukrainian, UK, Chinese)

60 71 61 70 69

TUNER_DATA TUN_DO TUNER_CLK TUN_LAT TUNED

COM1_DATA 111 COM1_CLK 110 COM2_DATA COM2_CLK XM_DACLAT COM2_DATA COM2_CLK FUNC-LAT D.MIX_LAT MIC VOL-LAT CCD_RY 2ND-RY 3ND-RY FUNC2_LAT COM1_DATA COM1_CLK DAC_DO 95 DAC_LAT 94 DA_RST 96 DA DO DA LAT DA RESET

V595_LAT 8 V595_OE 7 XM-DA_LAT 10

COM1-DAT COM1-CLK

15 (Page 43)

72 RDS_DATA 165 RDS_CLK

COM2_DATA 113 COM2_CLK 112 FUNC_LAT 91

(Page 44)

4

4/8_RY PROTECTOR

87 4/8_RY 163 PROTECTOR

SYSTEM CONTROLLER IC2003 (1/3)

D.MIX_LAT 80 MIC_ON VOL_LAT CCD_RY 2ND_RY 3ND-RY 26 92 105 106 107

16 (Page 39)

D1001 D1002 D1005 D1004 D1003

SP-A-RY SP-B-RY REAR-RY

(Page 40)

5

SB-RY C-RY PREOUT-RY HP-RY HPSW

81 83 86 85 84 76 79 23

SP-A_RY SP-B_RY REAR_RY SB_RY C_RY PREOUT_RY HP_RY HP_IN

FUNC2_LAT 90

17 (Page 35)

R-CH is omitted due to same as L-CH. SIGNAL PATH : AUDIO (ANALOG) : AUDIO (DIGITAL)

STR-DA5300ES

33

33

STR-DA5300ES

6-2. BLOCK DIAGRAM DSP Section DATA SELECTOR IC5013 11 3A 10 3B 2 1A 3 1B DSP1 IC5002 SI_A SI_B SI_C SI_D SI_E BCK LRCK P14 M13 M14 L14 K14 DPSIA DPSIB DPSIC DPSID DPSIE DPSOA DPSOB DPSOC DPSOD P10 P11 P12 P13 3Y 9

1Y 4 DSP2 IC5202M13 DPSIB M14 DPSIC

5 2A 2Y 7 6 2B SELECT 1

DPSOE N14 DPDVBCK H14 DPDVLRCK J14

L14 DPSID K14 DPSIE P14 DPSIA G14 DPBCK H13 DPLRCK F1 FLAG1 F14 DPFSCK

DPSOA DPSOB DPSOC DPSOD

P10 P11 P12 P13

SDO1 SDO2 SDO3 SDO4

20 (Page 35)

G14 DPBCK H13 DPLRCK D5001

DPDVBCK H14 DPDVLRCK J14

BCK LRCK S-RAM IC5207

(Page 33)

9

AD0 AD7 ADDRESS LATCH IC5209 D0 D7 ALE N2 DAI_P1 P15 ADDRESS LATCH IC5210 AD8 AD15 D0 D7 11 LE O0 O7 11 LEDSP1_A16

I/O0 I/O7

P_ERROR E14 DIR-ERR MCK DIR_NONAU F1 FLAG1 F14 DPFSCK F13 NONAUDIO

FLASH MEMORY IC5006 DQ0 DQ7 ADDRESS LATCH IC5009 D0 D7 O0 O7

F13 P_ERROR

AD0 AD7

O0 O7

A0 A16

ALE N2 AD8 AD15

11 LE DQ15/A-1, A0 A19

ADDRESS LATCH IC5010 D0 D6 11 LE WR M2 RD N3 O0 O4 O6 13

26 CE# 11 WE# 28 OE# 12 RESET# S-RAM IC5007

RD N3 WR M2 SPICLK B9 MOSI A9 SF2_DSP2_CE E14 B4 CLKIN X5201 25MHz A2 XTAL SF2_DSP2_MAS P9 BOOTCFG0 C2 DSP2_BOOTCFG0 DSP2_BOOTCFG1 DSP2_SPICLK DSP2_MOSI DSP2_MISO BUFFER IC5211 FLIP-FLOP IC5212

41 OE 17 WE

SERIAL FLASH IC5213 SF2_CPU_CE SF2_DSP2_MAS 1 CE#

B4 CLKIN X5001 12.288MHz A2 XTAL MISO A10 MOSI A9 SPICLK B9 BOOTCFG0 C2 BOOTCFG1 C1 SPIDS A11 FLAG0 F2 RESET B10 1 DSP1_MISO DSP1_MOSI DSP1_SPICLK DSP1_BOOTCFG0 DSP1_BOOTCFG1 DSP1_SPIDS DSP1_INT DSP1_RESET IC5012

I/O0 I/O7 A0 A18 8 CE 37 OE 15 WE

6 SCK 5 SI 2 SO

BOOTCFG1 C1 MISO A10 SPIDS A11 FLAG0 F2 RESET B10

DSP2_SPIDS DSP2_INT DSP2_RESET

DSP1_MOSI DSP1_MISO DSP1_SPICLK DSP1_SPIDS DSP1_INT

DSP1_RESET DSP1_BOOTCFG0 DSP1_BOOTCFG1

SF2_DSP2_MAS SF2_CPU_CE DSP2_MOSI DSP2_MISO DSP2_SPICLK DSP2_SPIDS DSP2_INT DSP2_RESET

DSP2_BOOTCFG0

MD_DATA MD_BUSY MD_INT

89 MD_DATA 63 MD_BUSY 82 MD_INT 90 DM_DATA 64 DM_BUSY

(Page 35) 19

DM_DATA DM_BUSY

93 92 94 11 83 12 13 14

17 20 100 99 101 21 84 22 25 26

DSP2_BOOTCFG1

(Page 35) 18

D232C_RX D232C_TX

102 SI3 103 SO3

RDATA0

9

10

SF2_DSP2_MAS SF2_CPU_CE DSP2_MOSI DSP2_MISO DSP2_SPICLK DSP2_SPIDS DSP2_INT DSP2_RESET

DSP1_RESET DSP1_BOOTCFG0 DSP1_BOOTCFG1

DSP2_BOOTCFG0 DSP2_BOOTCFG1

DSP2_SIB_SEL

DSP1_MOSI DSP1_MISO DSP1_SPICLK DSP1_SPIDS DSP1_INT

P_ERROR

MD2 DRST_TRG DUCOM_RESET

52 MD2 36 DRST_TRG 55 XRESET

SIGNAL PATHDSP CONTROLLER IC5208 XOUT 57 XIN 58 X5202 12.5MHz

: AUDIO (DIGITAL)

STR-DA5300ES

34

34

STR-DA5300ES

6-3. BLOCK DIAGRAM DIGITAL AUDIO Section LIP SYNC ADJUST IC2223 SD01 SD02 SD03 SD04 4 DIA 5 DIB 6 DIC 7 DID DOA DOB DOC DOD DQ0 DQ15 A0 A10, BA WEN CSN CASN RASN 43 40 42 41 15 18 16 17 36 14 35 34 19 20 21 22 DQ1 DQ16 VOUT3 12 A0 A11 WE CS CAS RAS UDQM LDQM CLK CKE VOUT4 11 SD-RAM IC2224 VOUT7 16 LOW-PASS FILTER IC2219 R-CH D/A-SBL LOW-PASS FILTER IC2221 R-CH D/A-SL 45 46 47 31 D/A CONVERTER IC2218 DATA1 DATA2 DATA3 DATA4 VOUT1 14 LOW-PASS FILTER IC2222 R-CH D/A-L

VOUT2 13

21 (Page 39)

(Page 34) 20DQM 31 CLKO 30 CKE 29 SI 10 SCLK 9 3 BCKI 2 MCKI DMUTEN 14 RSTN 15 SIO 11 XCS 8

VOUT8 20

VOUT5 10 LOW-PASS FILTER IC2220

D/A-C

VOUT6 9

D/A-SW

BCK LRCK

40 BCK 41 LRCK 38 SCKI DA DO COM1_DATA COM1_CLK DA LAT DA RESET 33 34 35 36 37 MDO MDI MC ML RST

(Page 37) 22

9850_INIT 9850_FS

157 9850_INIT 158 9850_FS

(Page 33) 17

(Page 43) 23

DMPORT_TX DMPORT_RX DMPORT_DET CEC_TX CEC_RX POW-RY STOP STOP VUCOM_TX VUCOM_RX VUCOM_BUSY VUCOM_MD VYCOM_FLG VUCOM_RST

154 DMPORT_DM/M 155 DMPORT_M/DM 156 DMPORT_DET 47 CEC_OUT 121 CEC_IN 75 POW_RY 82 STOP STB +3.3V SYSTEM MUTING SWICTH Q2205, 2206

R-CH is omitted due to same as L-CH. SIGNAL PATH : AUDIO (ANALOG)

D/A MCK BUFFER IC2216 ERR ANA/DIGI

: AUDIO (DIGITAL)

(Page 36) 24 (Page 44) 25

10 (Page 33)

(Page 38) 26

140 141 142 124 125 136

VIDEO-UCOM_V/M VIDEO-UCOM_M/V VIDEO-UCOM_BUSY VIDEO-UCOM_MODE VIDEO-UCOM_END-FLAG VIDEO-UCOM_RESET EEPROM_SDA 174 EEPROM_SCL 175

EEPROM IC2007 5 SDA 6 SCL

RESET SIGNAL GENERATOR IC2005 DATA SELECTOR IC2010 9 2Y 1Y 2C1 2C2 2C0 7 11 12 10

D232C_RX

18 (Page 34)D232C_TX

(Page 43) 27 (Page 44) 28 (Page 43) 29

XM_UART_TX XM_UART_RX XM RESET D_POW XM POW SIRI_TX SIRI_RX SIRI_POW_EN MD_DATA MD_BUSY MD_INT

137 XMUART_XM/M 138 XMUART_M/XM 139 XM_RESET 78 D_POWER 3 XM_POW 148 SIRIUS_TX 149 SIRIUS_RX 77 SIRIUS-POW_EN 144 M-D_DATA 51 MD_BUSY 54 M-D_INT 143 D-M_DATA 52 DM_BUSY

RESET SWITCH IC2004 X1 40 X2001 4MHz X0 39 RESET SIGNAL BUFFER IC2006

RX232C

30 (Page 38)TX232C

4 1C1 5 1C2

A B 170FSRATE2

55 56 62AVSYNC_RSTN AVSYNC_XCS AVSYNC_SIO

59MUTE

126RST_TRG

131INITX

14 2 232C-SEL1 232C-SEL2 RS232C_TX RS232C_RX 166 167 135 134 BUFFER IC2009 LEVEL SHIFT IC2002

RS-232C DRIVER IC1499 12 R1OUT 11 T1IN R1IN 13 T1OUT 14 2 3J1499 RS-232C

(Page 34) 19

DM_DATA DM_BUSY

MD2 DRST_TRG DUCOM_RESET

50 DSP-UCOM_MODE 49 DSP-UCOM_END-FLAG 53 DSP-UCOM_RESET

SYSTEM CONTROLLER IC2003 (2/3)

MD2 128

STR-DA5300ES

35

35

STR-DA5300ES

6-4. BLOCK DIAGRAM HDMI Section (1/2) Q [4] - Q [11], Q[16] -Q[23], Q[28]-Q[35] ODCK, HSYNC, VSYNC, DE

32 (Page 38)

Q [4] - Q [11], Q[16] -Q[23], Q[28]-Q[35]

DATA1+ DATA1 DATA2+ DATA2 CLOCK+ CLOCK SDA (5V) SCL (5V) HOT PLUG DET +5V POWER CEC

4 6 1 3 10 12 16 15 19 18 13 3 LEVER SHIFT Q3501 2 1 GATE IC3524(1/3)

25 R0X1+ 24 R0X128 R0X2+ 27 R0X219 R0XC+ 18 R0XC30 DSDA0 31 DSCL0 16 HPD016 -13,10 -7,3 -1, 144,141 -138,135 -132, 129 -126,123 -120, 117 -114,111 -108

ODCK HSYNC VSYNC DE

DATA0+ DATA0

7 9

22 R0X0+ 21 R0X0-

TX0+ 34 TX0 3398 -90, 86 -77 75 -67, 63 -56 D0 -D35

7 9 4 6 1 3 10 12 16 15

DATA0+ DATA0 DATA1+ DATA1 DATA2+ DATA2 CLOCK+ CLOCK SDA (5V) SCL (5V) CN3511 HDMI ASSIGNABLE (INPUT ONLY) OUT

Q0 Q35

CN3501 HDMI ASSIGNABLE (INPUT ONLY) IN 6

TX0+ 7 TX0- 8 TX1+ 4 TX1- 5 TX2+ 1 TX2- 2 TXC+ 10 TXC- 11

44 R0X0+ 43 R0X0 48 R0X1+ 47 R0X1 52 R0X2+ 51 R0X2 40 R0XC+ 39 R0XC

36

TX1+ 37 TX1 36 TX2+ 40 TX2 39 TXC+ 31 TXC 30 DSDA 47 DSCL 46

32 RPWR0

ODCK HSYNC VSYNC DE

5 20 21 19

88 2 3 1

IDCK HSYNC VSYNC DE

HDMI RECEIVER IC3511 (1/2) SPDIF 7881 -84

HDMI TRANSCEIVER IC3513 HPD 51 21 DL2 4 SPDIF96

19

HOT PLUG DET

DATA0+ DATA0 DATA1+ DATA1 CN3502 HDMI ASSIGNABLE (INPUT ONLY) IN 5 DATA2+ DATA2 CLOCK+ CLOCK SDA (5V) SCL (5V) HOT PLUG DET +5V POWER CEC

7 9 4 6 1 3 10 12 16 15 19 18 13 11 LEVER SHIFT Q3502 12 13

17 20

42 R1X0+ 41 R1X0- HDMI INPUT SELECT 45 R1X1+ IC3503 44 R1X148 R1X2+ 47 R1X239 R1XC+ 38 R1XC50 DSDA1 51 DSCL1 TPWR/I2CADDR 79 36 HPD1 HPDIN 76 RESET# 13 9185_HPD[1] 9185_RST[1] PWR5V

4

4

SD0 -SD3 X3501 28.322MHz 94 XTALOUT 95 XTALIN 30 R1PWR5V 28 DSDA1 29 DSCL1

SD0 -SD3 CEC DATA SWITCH Q2001 2004 INT 24 RESET# 25 CSDA 49 CSCL 48 TX_INT TX_RST UC3V_SDA UC3V_SCL

13 CEC_TX CEC_RX

CEC

4

DL0, DR1, DL1, DR2 DCLK DR0 MCLK SCK WS

24 (Page 35)

(Page 37) 37

DSDA DSCL

MCLK 89 SCK 86 WS 85

15 16 5 11 10

UC3V_SDA, UC3V_SCL

33 (Page 38)

35 R0PWR5V

GATE IC3524(2/3)

52 RPWR1

SPDIF SD0 -SD3 MCK SCK WS

SD0 -SD3, SPDIF, MCK, SCK, WS

TSDA 77 TSCL 78 DATA0+ DATA0 DATA1+ DATA1 DATA2+ DATA2 CLOCK+ CLOCK SDA (5V) SCL (5V) HOT PLUG DET +5V POWER CEC 7 9 4 6 1 3 10 12 16 15 19 18 13 8 LEVER SHIFT Q3503 9 10 GATE IC3524(3/3) 62 R2X0+ 61 R2X065 R2X1+ 64 R2X168 R2X2+ 67 R2X259 R2XC+ 58 R2XC70 DSDA2 71 DSCL2 56 HPD2 72 RPWR2 LSDA/EPSEL[0] 14 LSCL/EPSEL[1] 15

33 DSDA0 34 DSCL0 26 CSDA 27 CSCL

34 (Page 37)


DATA SELECTOR IC3508 4 2Y3 5 2Y1 1 2Y0 2-COM 3 5

EEPROM IC3509 SDA

11 1Y3 1-COM 13 14 1Y1 12 1Y0 B A 9 10

6

SCL WP 7

(Page 37) 31

CEC

(Page 37) 52

UC3V_SDA UC3V_SCL

UC3V_SDA UC3V_SCL

9185_HPD[1]

9185_RST[1]

SIGNAL PATH : AUDIO (DIGITAL) : VIDEO

939185_1_HPD1-3

949185_1_RST

118 117UC3V_SCL UC3V_SDA

9

8

EDIO_SEL1 EDIO_SEL0

VIDEO SYSTEM CONTROLLER IC3610 (1/3)

STR-DA5300ES

36

36

TX_RST TX_INT

TX_RST TX_INT

30 123

STR-DA5300ES

6-5. BLOCK DIAGRAM HDMI Section (2/2) SD0 -SD3, SPDIF, MCK, SCK, WS XMDATA, XMFS, XM256FS, XM64FS

DATA0+ DATA0 DATA1+ DATA1 DATA2+ DATA2 CLOCK+ CLOCK SDA (5V) SCL (5V) HOT PLUG DET +5V POWER CEC

7 9 4 6 1 3 10 12 16 15 19 18 13 6 LEVER SHIFT Q3504 5 4 GATE IC3525(1/3)

22 R0X0+ 21 R0X025 R0X1+ 24 R0X128 R0X2+ 27 R0X219 R0XC+ 18 R0XC30 DSDA0 31 DSCL0 16 HPD0

(Page 36) 34

35 (Page 43)


TX0+ TX0TX1+ TX1TX2+ TX2-

7 8 4 5 1 2

62 R1X0+ 61 R1X0 66 R1X1+ 65 R1X1 70 R1X2+ 69 R1X2 58 R1XC+ 57 R1XC SPDIF SD0 SD1 SD2 SD3 WS MCK SCK

DIGITAL AUDIO PROCESSOR IC3519

DATA SELECTOR IC3520 SPDIF 6 IC0 4 IC2 10 2C0 11 2C1 12 2C2 1Y 7 HDMI_SPDIF HDMI_BCK, HDMI_LRCK, HDMI_MCK

1 8

(Page 33) (Page 33)

WS PLRCK 20 43 39 42 41 DSISL DSIFL DSISW DSICT MCKOUT 17 PBCK 19 POFLR 23 40 DSIFR 27 MCK 38 DSBCK POCSW 22 POSLR 21 MCK XM256FS SCK XM64FS XMFS

2Y 9 A 14 B 2

HDMI_LRCK

TXC+ 10 TXC- 11

32 RPWR0

44 DSISR

DATA SELECTOR IC3521 6 1C0 5 1C1 4 1C2 10 2C0 11 2C1 12 2C2 HDMI_MCK

1Y 7

DATA0+ DATA0 DATA1+ DATA1 CN3505 HDMI ASSIGNABLE (INPUT ONLY) IN 2 DATA2+ DATA2 CLOCK+ CLOCK SDA (5V) SCL (5V) HOT PLUG DET +5V POWER CEC

7 9 4 6 1 3 10 12 16 15 19 18 13 11 LEVER SHIFT Q3505 12 13

42 R1X0+ 41 R1X045 R1X1+ 44 R1X148 R1X2+ 47 R1X239 R1XC+ 38 R1XC50 DSDA1 51 DSCL1 36 HPD1

2Y 9 A 14 B 2

HDMI_BCK

HDMI INPUT SELECT IC3504

HDMI RECEIVER IC3511 (2/2)

DATA SELECTOR IC3518 LSDA/EPSEL[0] 14 LSCL/EPSEL[1] 15 UC3V_SDA UC3V_SCL

HDMI_ERROR

7

(Page 33)

52 (Page 36)

INTT 47 SEL4FS 3 SD0 XMDATA

DATA SELECTOR IC3522 6 1C0 5 1C1 4 1C2 10 2C0 11 2C1 12 2C2

1Y 7

SD0

TPWR/I2CADDR 79 TDSA 77 TSCL 78

PWR5V DSDA DSCL

GATE IC3525(2/3)

52 RPWR1

37 (Page 36)

SD1

2Y 9 A 14 B 2

SD1

36 (Page 33)

D3502 MUTEOUT 75 DATA0+ DATA0 DATA1+ DATA1 DATA2+ DATA2 CLOCK+ CLOCK SDA (5V) SCL (5V) HOT PLUG DET +5V POWER CEC 7 9 4 6 1 3 10 12 16 15 19 18 13 8 LEVER SHIFT Q3506 9 10 62 R2X0+ 61 R2X065 R2X1+ 64 R2X168 R2X2+ 67 R2X259 R2XC+ 58 R2XC70 DSDA2 71 DSCL2 56 HPD2 72 RPWR2 SD3 HPDIN 76 RESRT# 13 9185_HPD[2] 9185_RST[2] RESET# 100 INT 102 RESET RX_INT D

STR-DA5300ES

Documents

Transcript of STR-DA5300ES