Sticks & Stones Unlimited, Inc. - Rapp Industrial Sales FSB-24 FJB-24 #292F C61-F 4 x 1 x 1/2 2 lbs....

44
Sticks & Stones Unlimited, Inc. www.sticksandstonesunl.com General Catalog Distributed By: 17612_Sticks_P1_10 7/20/05 2:13 PM Page 1

Transcript of Sticks & Stones Unlimited, Inc. - Rapp Industrial Sales FSB-24 FJB-24 #292F C61-F 4 x 1 x 1/2 2 lbs....

Sticks & Stones Unlimited, Inc.w w w. s t i c k s a n d s t o n e s u n l . c o m

General Catalog

Distributed By:

17612_Sticks_P1_10 7/20/05 2:13 PM Page 1

2

Table of ContentsItem Page

Aluminum Oxide Bench StonesCombination – Coarse/Fine – Oil Filled ..................................................................................................... 4Single Grit – Oil Filled ................................................................................................................................ 4

Silicon Carbide Bench StonesCombination – Coarse/Fine – Oil Filled ..................................................................................................... 5Single Grit – Oil Filled ................................................................................................................................ 5

Specialty “Economy” Norton Bench Stones ............................................................................................... 5Boron Carbide Dressing Sticks .................................................................................................................... 5Tool Room And Die Finishing Stones

Square – Aluminum Oxide & Silicon Carbide – Oil Filled .......................................................................... 6Triangular – Aluminum Oxide & Silicon Carbide – Oil Filled ..................................................................... 7Round – Aluminum Oxide & Silicon Carbide – Oil Filled ........................................................................... 8Half Round – Aluminum Oxide & Silicon Carbide – Oil Filled ................................................................... 9

Silversmiths’ StonesAluminum Oxide ....................................................................................................................................... 10Specialty Shapes – Aluminum Oxide ....................................................................................................... 10

Round Edge Slip Stones ............................................................................................................................. 11Arkansas Round Edge Slip Stones ............................................................................................................ 11Hard Arkansas Carving Tools ...................................................................................................................... 11Hard Arkansas Jewelers Stone & Penknife Pieces ....................................................................................11Aluminum Oxide Engravers Pencils ............................................................................................................12Engravers Chuck and Points ........................................................................................................................12Arkansas Bench Stones – Hard & Soft .......................................................................................................12Mounted Arkansas Bench Stones In Box – Hard & Soft ...........................................................................12Arkansas Square And Triangle Files ...........................................................................................................12Special Shaped Arkansas Files – Hard Only ..............................................................................................13Jointer Stones ...............................................................................................................................................13Pocket Stone With Plastic Pouch .................................................................................................................13Molded Boat Rubs .........................................................................................................................................14Gouge Sharpening Stone .............................................................................................................................14Carving Slips....................................................................................................................................................14Silicon Carbide Hand Hones ........................................................................................................................14General Purpose File ....................................................................................................................................14Utility Files .....................................................................................................................................................14Carving Knife Sharpener ..............................................................................................................................15Kitchen Knife Sharpener ..............................................................................................................................15Home and Garden Sharpener .......................................................................................................................15Combination Axe Stone ................................................................................................................................15Machine Knife Stone .....................................................................................................................................15Scythe Stones ................................................................................................................................................15Tradesmen’s Stones ......................................................................................................................................15Wheel Dresser ...............................................................................................................................................16Dressing Sticks ..............................................................................................................................................16Cutlery Bench Stones ...................................................................................................................................16Crystolon Cutlers Stone ...............................................................................................................................16Reversible Oil Stone in Beautiful Hinged Wood Box with Latch ..............................................................16Wood Boxes Only ..........................................................................................................................................16S&S Burr Breaker ..........................................................................................................................................17Blanchard “Burr Busters” .............................................................................................................................17Aluminum Oxide/Soft Arkansas Combo .....................................................................................................17Norton Multi-Oilstone Units ..........................................................................................................................17Griddle Bricks ................................................................................................................................................18Rubbing Brick with Handle ...........................................................................................................................18Rubbing Bricks – Plain & Fluted ..................................................................................................................18Half Round Foundry Core Files ...................................................................................................................18

17612_Sticks_P1_10 7/20/05 2:13 PM Page 2

3

Table of Contents (cont.)Item Page

Flat Core Files with Plastic Handles ...........................................................................................................19Fiberglass Reinforced – S/C Resin Bond ...................................................................................................19Dressing Sticks ..............................................................................................................................................19Mold & Diemakers Polishing Stones ...........................................................................................................20Pencil Stones .................................................................................................................................................20Diemaker Stones ...........................................................................................................................................20Moldmaker Stones ........................................................................................................................................21Hard Moldmakers Stones .............................................................................................................................21EDM Stones ...................................................................................................................................................21Superfine Stones ...........................................................................................................................................21Resin Bonded Stones ...................................................................................................................................22General Polishing Stones .............................................................................................................................22Hard Polishing Stones ..................................................................................................................................22Ruby Stones ...................................................................................................................................................22Metal Polishing & Cleaning ..........................................................................................................................23Rubber Bond Sticks ......................................................................................................................................23Cotton Fiber Reinforced Resin Sticks .........................................................................................................23MD-1 Mandrel Driver .....................................................................................................................................24Superior – Tennessee Two Stone Hone .......................................................................................................26Sunnen-Superior – Tennessee Hone ...........................................................................................................27Norton Diamond Hand Hones ......................................................................................................................28Portable Hone Kit ..........................................................................................................................................29ASI General Purpose Shop Hones ..............................................................................................................29BCD-Hone Kit .................................................................................................................................................29Portable Honing Devices

S&S-Mini ...................................................................................................................................................30S&S-Junior ................................................................................................................................................30S&S-Middle ...............................................................................................................................................30Model S&S-Jumbo ....................................................................................................................................31Model S&S-Maxi-Jumbo ...........................................................................................................................31

Hand Feed Portable HoneASI-218 .....................................................................................................................................................32

Aligner™ Guided Sharpening Kits ..............................................................................................................34Diamond Whetstones™ - Bench Models .....................................................................................................34Pocket Models ................................................................................................................................................34Diafold™ Diamond Whetstone™ ..................................................................................................................34Diafold™ Sharpeners & Diafold™ Folding Files ........................................................................................34Diamond Mini-Sharp™ Sharpener ...............................................................................................................34General Purpose Diamond Dressing Tools .................................................................................................35Single Point Tools ..........................................................................................................................................35Flex-Hone® Tool ..............................................................................................................................................36S&S Finishing Stick ......................................................................................................................................38Norton Pacesetter Mounted Points

A Shapes ..................................................................................................................................................39B Shapes ..................................................................................................................................................40B Shapes (continued) ...............................................................................................................................41W Shapes .................................................................................................................................................42W Shapes (continued) ..............................................................................................................................43

Terms and Conditions ...................................................................................................................................44

17612_Sticks_P1_10 7/20/05 2:13 PM Page 3

Single Grit – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Stone Size Approx. Weight730006 Stones # # # # & Shape Per Std. Pkg.

00078 AFB-14 FB-14 N.A. A60-FO 4 x 1 x 1/4 1 lbs.00145 AMB-14 MB-14 N.A. A60-MO 4 x 1 x 1/4 1 lbs.00009 ACB-14 CB-14 N.A. A60-CO 4 x 1 x 1/4 1 lbs.00079 AFB-24 FB-24 N.A. A61-FO 4 x 1 x 1/2 2 lbs.00146 AMB-24 MB-24 N.A. A61-MO 4 x 1 x 1/2 2 lbs.00010 ACB-24 CB-24 N.A. A61-CO 4 x 1 x 1/2 2 lbs.00080 AFB-35 FB-35 N.A. A63-FO 5 x 2 x 5/8 4 lbs.00147 AMB-35 MB-35 N.A. A63-MO 5 x 2 x 5/8 4 lbs.00076 AFB-6 FB-6 N.A. A66-FO 6 x 2 x 1 7 lbs.00143 AMB-6 MB-6 N.A. A66-MO 6 x 2 x 1 7 lbs.00007 ACB-6 CB-6 N.A. A66-CO 6 x 2 x 1 7 lbs.00077 AFB-8 FB-8 N.A. A69-FO 8 x 2 x 1 8 lbs.00144 AMB-8 MB-8 N.A. A69-MO 8 x 2 x 1 8 lbs.00008 ACB-8 CB-8 N.A. A69-CO 8 x 2 x 1 8 lbs.

4

Combination – Coarse/Fine – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Stone Size Approx. Weight730006 Stones # # # # & Shape Per Std. Pkg.

00004 AB-64 IB-64 N.A. A80-CFO 4" DIA. x 1" THICK 7 lbs.00005 AB-134 IB-134 #144 A75-CFO 4 x 1-3/4 x 5/8 3 lbs.00003 AB-45 IB-45 N.A. A76-CFO 5 x 2 x 3/4 4 lbs.00001 AB-6 IB-6 #433 A77-CFO 6 x 2 x 1 7 lbs.00002 AB-8 IB-8 #431 A79-CFO 8 x 2 x 1 8 lbs.

Aluminum Oxide Bench StonesMin. Pkg. 1Std. Pkg. 5

F = Fine M = Medium C = CoarseMin. Pkg. 1Std. Pkg. 5

UPC Code # Sticks & Norton Carbo Bay State Approx. Weight730006 Stones # # # # Per Std. Pkg.

00484 XB-1 XB-1 N.A. N.A. 4-1/2 oz. Can 8 lbs.00486 XB-5 XB-5 N.A. N.A. 1 Pint Can 20 lbs.00485 XB-2 XB-2 N.A. N.A. 1 Quart Can 20 lbs.

Size

We Offer “Norton” Bear Brand sharpening oilBear Oil is a highly refined sharpening stone oil which meets U.S. Pharmacopia

standards of purity for mineral oils.

17612_Sticks_P1_10 8/3/05 12:50 PM Page 4

5

Single Grit – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Stone Size Approx. Weight730006 Stones # # # # & Shape Per Std. Pkg.

00265 FSB-14 FJB-14 #145 C60-F 4 x 1 x 1/4 1 lbs.00380 MSB-14 MJB-14 #146 C60-M 4 x 1 x 1/4 1 lbs.00217 CSB-14 CJB-14 #147 C60-C 4 x 1 x 1/4 1 lbs.00266 FSB-24 FJB-24 #292F C61-F 4 x 1 x 1/2 2 lbs.00381 MSB-24 MJB-24 #292M C61-M 4 x 1 x 1/2 2 lbs.00218 CSB-24 CJB-24 #292C C61-C 4 x 1 x 1/2 2 lbs.00267 FSB-35 FJB-35 #124 C63-F 5 x 2 x 5/8 4 lbs.00382 MSB-35 MJB-35 #125 C63-M 5 x 2 x 5/8 4 lbs.00263 FSB-6 FJB-6 #121 C66-F 6 x 2 x 1 7 lbs.00378 MSB-6 MJB-6 #122 C66-M 6 x 2 x 1 7 lbs.00215 CSB-6 CJB-6 #123 C66-C 6 x 2 x 1 7 lbs.00264 FSB-8 FJB-8 N.A. C69-F 8 x 2 x 1 8 lbs.00379 MSB-8 MJB-8 N.A. C69-M 8 x 2 x 1 8 lbs.00216 CSB-8 CJB-8 N.A. C69-C 8 x 2 x 1 8 lbs.00268 FSB-48 N.A. #118 N.A. 8 x 2 x 3/4 5 lbs.00383 MSB-48 N.A. #119 N.A. 8 x 2 x 3/4 5 lbs.00219 CSB-48 N.A. #120 N.A. 8 x 2 x 3/4 5 lbs.

Combination – Coarse/Fine – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Stone Size Approx. Weight730006 Stones # # # # & Shape Per Std. Pkg.

00450 SB-64 JB-64 #107 C80-CF 4" DIA. x 1" THICK 7 lbs.00453 SB-134 JB-134 #112 C75-CF 4 x 1-3/4 x 5/8 3 lbs.00449 SB-45 JB-45 #111 C76-CF 5 x 2 x 3/4 4 lbs.00446 SB-6 JB-6 #109 C77-CF 6 x 2 x 1 7 lbs.00448 SB-8 JB-8 #108 C79-CF 8 x 2 x 1 8 lbs.

Silicon Carbide Bench StonesMin. Pkg. 1Std. Pkg. 5

F = Fine M = Medium C = CoarseMin. Pkg. 1Std. Pkg. 5

00483 UPB-8 Quick Cut Stone 8 x 2 x 3/4 Std. Pk. 10 20 lbs.

Special “Economy” Norton Bench Stones

Boron Carbide Dressing SticksFor tool room applications – Custom sizes also available

UPC Code # Sticks & Norton Boride Pdts. ESKStone Size & Shape730006 Stones # # # #

00538 B-1 Norbide Stick Boride Stick Tetrabor Stick 3/16 x 1/2 x 3

17612_Sticks_P1_10 7/20/05 2:13 PM Page 5

6

Square – Aluminum Oxide & Silicon Carbide – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Stone Size Approx. Weight730006 Stones # # # # & Shape Per Std. Pkg.

00269 FSF-14 FJF-14 F-1 C1-F 4 x 1/4 SQ. 8 oz.00384 MSF-14 MJF-14 M-1 C1-M SILICON 8 oz.00485 CSF-14 N.A. C-1 C1-C CARBIDE 8 oz.00081 AFF-14 FF-14 F-2 A1-FO 4 x 1/4 SQ. 8 oz.00148 AMF-14 MF-14 M-2 A1-MO ALUMINUM 8 oz.00011 ACF-14 N.A. C-2 A1-CO OXIDE 8 oz.00272 FSF-34 FJF-34 F-5 C3-F 4 x 3/8 SQ. 1-1/4 lbs.00387 MSF-34 MJF-34 M-5 C3-M SILICON 1-1/4 lbs.00223 CSF-34 N.A. C-5 C3-C CARBIDE 1-1/4 lbs.00084 AFF-34 FF-34 F-6 A3-FO 4 x 3/8 SQ. 1-1/4 lbs.00151 AMF-34 MF-34 M-6 A3-MO ALUMINUM 1-1/4 lbs.00014 ACF-34 N.A. C-6 A3-CO OXIDE 1-1/4 lbs.00274 FSF-44 FJF-44 F-7 C5-F 4 x 1/2 SQ. 2-1/8 lbs.00389 MSF-44 MJF-44 M-7 C5-M SILICON 2-1/8 lbs.00225 CSF-44 N.A. C-7 C5-C CARBIDE 2-1/8 lbs.00086 AFF-44 FF-44 F-8 A5-FO 4 X 1/2 SQ. 2-1/8 lbs.00153 AMF-44 MF-44 M-8 A5-MO ALUMINUM 2-1/8 lbs.00016 ACF-44 N.A. C-8 A5-CO OXIDE 2-1/8 lbs.00271 FSF-26 N.A. C2-F 6 X 1/4 SQ. 12 oz.00386 MSF-26 N.A. N.A. C2-M SILICON 12 oz.00222 CSF-26 N.A. C2-C CARBIDE 12 oz.00083 AFF-26 N.A. A2-FO 6 X 1/4 SQ. 12 oz.00150 AMF-26 N.A. N.A. A2-MO ALUMINUM 12 oz.00013 ACF-26 N.A. A2-CO OXIDE 12 oz.00273 FSF-36 F-33 C4-F 6 X 3/8 SQ. 1-3/4 lbs.00388 MSF-36 N.A. M-33 C4-M SILICON 1-3/4 lbs.00224 CSF-36 C-33 C4-C CARBIDE 1-3/4 lbs.00275 FSF-46 F-35 C6-F 6 X 1/2 SQ. 3 lbs.00390 MSF-46 N.A. M-35 C6-M SILICON 3 lbs.00226 CSF-46 C-35 C6-C CARBIDE 3 lbs.00087 AFF-46 FF-46 F-36 A6-FO 6 X 1/2 SQ. 3 lbs.00154 AMF-46 MF-46 M-36 A6-MO ALUMINUM 3 lbs.00017 ACF-46 CF-46 C-36 A6-CO OXIDE 3 lbs.00276 FSF-56 F-37 C8-F 6 X 5/8 SQ. 4-5/8 lbs.00391 MSF-56 N.A. M-37 C8-M SILICON 4-5/8 lbs.00227 CSF-56 C-37 C8-C CARBIDE 4-5/8 lbs.00088 AFF-56 FF-56 F-38 A8-FO 6 X 5/8 SQ. 4-5/8 lbs.00155 AMF-56 MF-56 M-38 A8-MO ALUMINUM 4-5/8 lbs.00018 ACF-56 CF-56 C-38 A8-CO OXIDE 4-5/8 lbs.00277 FSF-66 F-39 C9-F 6 X 3/4 SQ. 6-1/4 lbs.00392 MSF-66 N.A. M-39 C9-M SILICON 6-1/4 lbs.00228 CSF-66 C-39 C9-C CARBIDE 6-1/4 lbs.00089 AFF-66 FF-66 F-40 A9-FO 6 X 3/4 SQ. 6-1/4 lbs.00156 AMF-66 MF-66 M-40 A9-MO ALUMINUM 6-1/4 lbs.00019 ACF-66 CF-66 C-40 A9-CO OXIDE 6-1/4 lbs.00278 FSF-76 F-41 C10-F 6 X 1 SQ. 11-1/2 lbs.00393 MSF-76 N.A. M-41 C10-M SILICON 11-1/2 lbs.00229 CSF-76 C-41 C10-C CARBIDE 11-1/2 lbs.00090 AFF-76 FF-76 F-42 A10-FO 6 X 1 SQ. 11-1/2 lbs.00157 AMF-76 MF-76 M-42 A10-MO ALUMINUM 11-1/2 lbs.00020 ACF-76 CF-76 C-42 A10-CO OXIDE 11-1/2 lbs.

Tool Room And Die Finishing Stones

F = Fine M = Medium C = Coarse

Bkn. Pkg. = 1-4Min. Pkg. = 5Std. Pkg. = 20

17612_Sticks_P1_10 7/20/05 2:13 PM Page 6

7

Triangular – Aluminum Oxide & Silicon Carbide – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Size & Weight Per730006 Stones # # # # Type Abrasive Std. Pkg.

00279 FSF-114 FJF-114 F-9 C15-F 4 x 1/4 TRI. 5 oz.00394 MSF-114 MJF-114 M-9 C15-M SILICON CARBIDE 5 oz.00091 AFF-114 FF-114 F-10 A15-FO 4 x 1/4 TRI. 5 oz.00158 AMF-114 MF-114 M-10 A15-MO ALUMINUM 5 oz.00021 ACF-114 N.A. C-10 A15-CO OXIDE 5 oz.00281 FSF-134 FJF-134 F-13 C16-F 4 x 3/8 TRI. 10 oz.00395 MFS-134 MJF-134 M-13 C16-M SILICON CARBIDE 10 oz.00092 AFF-134 FF-134 F-14 A16-FO 4 x 3/8 TRI. 10 oz.00160 AMF-134 MF-134 M-14 A16-MO ALUMINUM 10 oz.00022 ACF-134 N.A. C-14 A16-CO OXIDE 10 oz.00283 FSF-144 FJF-144 F-15 C17-F 4 x 1/2 TRI. 1 lb.00396 MSF-144 MJF-144 M-15 C17-M SILICON 1 lb.00233 CSF-144 N.A. C-15 C17-C CARBIDE 1 lb.00094 AFF-144 FF-144 F-16 A17-FO 4 x 0 1/2 TRI. 1 lb.00162 AMF-144 MF-144 M-16 A17-MO ALUMINUM 1 lb.00024 ACF-144 CF-144 C-16 A17-CO OXIDE 1 lb.00282 FSF-136 F-43 C14-F 6 x 3/8 TRI. 1-1/4 lbs.03012 MSF-136 N.A. M-43 C14-M SILICON 1-1/4 lbs.00232 CSF-136 C-43 C14-C CARBIDE 1-1/4 lbs.00093 AFF-136 F-44 A14-FO 6 x 3/8 TRI. 1-1/4 lbs.00161 AMF-136 N.A. M-44 A14-MO ALUMINUM 1-1/4 lbs.00023 ACF-136 C-44 A14-CO OXIDE 1-1/4 lbs.00095 AFF-146 FF-146 F-46 A18-FO 6 x 1/2 TRI. 1-1/2 lbs.00163 AMF-146 MF-146 M-46 A18-MO ALUMINUM 1-1/2 lbs.00025 ACF-146 CF-146 C-46 A18-CO OXIDE 1-1/2 lbs.00096 AFF-156 FF-156 F-48 A19-FO 6 x 5/8 TRI. 2-1/8 lbs.00164 AMF-156 MF-156 M-48 A19-MO ALUMINUM 2-1/8 lbs.00026 ACF-156 CF-156 C-48 A19-CO OXIDE 2-1/8 lbs.00097 AFF-166 FF-166 F-50 A20-FO 6 x 3/4 TRI. 2-3/4 lbs.00165 AMF-166 MF-166 M-50 A20-MO ALUMINUM 2-3/4 lbs.00027 ACF-166 CF-166 C-50 A20-CO OXIDE 2-3/4 lbs.00098 AFF-176 FF-176 F-52 A22-FO 6 X 1 TRI. 5-3/.4 lbs.00166 AMF-176 MF-176 M-52 A21-MO ALUMINUM 5-3/4 lbs.00028 ACF-176 CF-176 C-52 A21-CO OXIDE 5-3/4 lbs.

Tool Room And Die Finishing Stones

F = Fine M = Medium C = Coarse

Bkn. Pkg. = 1-4Min. Pkg. = 5Std. Pkg. = 20

17612_Sticks_P1_10 7/20/05 2:13 PM Page 7

8

Round – Aluminum Oxide & Silicon Carbide – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Size & Weight Per730006 Stones # # # # Type Abrasive Std. Pkg.

00287 FSF-214 FJF-214 F25 C25-F 4 x 1/4 RD. 8 oz.00399 MSF-214 MJF-214 M25 C25-M SILICON 8 oz.00238 CSF-214 N.A. C25 C25-C CARBIDE 8 oz.00099 AFF-214 FF-214 F26 A25-FO 4 x 1/4 RD. 8 oz.00167 AMF-214 MF-214 M26 A25-MO ALUMINUM 8 oz.00029 ACF-214 CF-214 C26 A25-CO OXIDE 8 oz.00288 FSF-234 FJF-234 F29 C26-F 4 x 3/8 RD. 13 oz.00401 MSF-234 MJF-234 M29 C26-M SILICON 13 oz.00240 CSF-234 N.A. C29 C26-C CARBIDE 13 oz.00100 AFF-234 FF-234 F30 A26-FO 4 x 3/8 RD. 13 oz.00168 AMF-234 MF-234 M30 A26-MO ALUMINUM 13 oz.00030 ACF-234 CF-234 C30 A26-CO OXIDE 13 oz.00290 FSF-244 FJF-244 F31 C27-F 4 x 1/2 RD. 1-5/8 lbs.00403 MSF-244 MJF-244 M31 C27-M SILICON 1-5/8 lbs.00242 CSF-244 CJF-244 C31 C27-C CARBIDE 1-5/8 lbs.00102 AFF-244 FF-244 F32 A27-FO 4 x 1/2 RD. 1-5/8 lbs.00170 AMF-244 MF-244 M32 A27-MO ALUMINUM 1-5/8 lbs.00032 ACF-244 CF-244 C32 A27-CO OXIDE 1-5/8 lbs.00101 AFF-236 F64 A28-FO 6 x 3/8 RD. 1-3/4 lbs.00169 AMF-236 N.A. M64 A28-MO ALUMINUM 1-3/4 lbs.00031 ACF-236 C64 A28-CO OXIDE 1-3/4 lbs.00291 FSF-246 F65 C29-F 6 x 1/2 RD. 2-3/8 lbs.00404 MSF-246 N.A. M65 C29-M SILICON 2-3/8 lbs.00243 CSF-246 C65 C29-C CARBIDE 2-3/8 lbs.00103 AFF-246 FF-246 F66 A29-FO 6 x 1/2 RD. 2-3/8 lbs.00171 AMF-246 MF-246 M66 A29-MO ALUMINUM 2-3/8 lbs.00033 ACF-246 CF-246 C66 A29-CO OXIDE 3-5/8 lbs.00104 AFF-256 FF-256 F68 A30-FO 6 x 5/8 RD. 3-5/8 lbs.00172 AMF-256 MF-256 M68 A30-MO ALUMINUM 3-5/8 lbs.00034 ACF-256 CF-256 C68 A30-CO OXIDE 3-5/8 lbs.00105 AFF-266 FF-266 F70 A31-FO 6 x 3/4 RD. 4-7/8 lbs.00173 AMF-266 MF-266 M70 A31-MO ALUMMINUM 4-7/8 lbs.00035 ACF-266 CF-266 C70 A31-CO OXIDE 4-7/8 lbs.00106 AFF-276 FF-276 F72 A32-FFO 6 x 1 RD. 9-1/4 lbs.00174 AMF-276 MF-276 M72 A32-MO ALUMINUM 9-1/4 lbs.00036 ACF-276 CF-276 C72 A32-CO OXIDE 9-1/4 lbs.

Tool Room And Die Finishing Stones

F = Fine M = Medium C = Coarse

Bkn. Pkg. = 1-4Min. Pkg. = 5Std. Pkg. = 20

17612_Sticks_P1_10 7/20/05 2:13 PM Page 8

9

Half Round – Aluminum Oxide & Silicon Carbide – Oil Filled

UPC Code # Sticks & Norton Carbo Bay State Size & Weight Per730006 Stones # # # # Type Abrasive Std. Pkg.

00295 FSF-314 F17 C35-F 4 x 1/4 H.R. 5 oz.00408 MSF-314 N .A. M17 C35-M SILICON 5 oz.00247 CSF-314 C17 C35-C CARBIDE 5 oz.00107 AFF-314 FF-314 F18 A35-FO 4 x 1/4 H.R. 5 oz.00175 AMF-314 MF-314 M18 A35-MO ALUMINUM 5 oz.00037 ACF-314 CF-314 C18 A35-CO OXIDE 5 oz.00296 FSF-334 F21 C36-F 4 x 3/8 H.R. 8 oz.00410 MSF-334 N.A. M21 C36-M SILICON 8 oz.00249 CSF-334 C21 C36-C CARBIDE 8 oz.00109 AFF-334 FF-334 F22 A36-FO 4 x 3/8 H.R. 8 oz.00177 AMF-334 MF-334 M22 A36-MO ALUMINUM 8 oz.00039 ACF-334 CF-334 C22 A36-CO OXIDE 8 oz.00298 FSF-344 F23 C37-F 4 x 1/2 H.R. 13 oz.00412 MSF-344 N.A. M23 C37-M SILICON 13 oz.00251 CSF-344 C23 C37-C CARBIDE 13 oz.00111 AFF-344 FF-344 F24 A37-FO 4 x 1/2 H.R. 13 oz.00178 AMF-344 MF-344 M24 A37-MO ALUMINUM 13 oz.00041 ACF-334 CF-344 C24 A37-CO OXIDE 13 oz.00110 AFF-336 FF-336 C54 A38-FO 6 x 3/8 H .R. 1 lb.03011 AMF-336 MF-336 M54 A38-MO ALUMINUM 1 lb.00040 ACF-336 CF-336 C54 A38-CO OXIDE 1 lb.00299 FSF-346 F55 C39-F 6 x 1/2 H.R. 1-1/4 lbs.00413 MSF-346 N.A. M55 C39-M SILICON 1-1/4 lbs.00252 CSF-346 C55 C39-C CARBIDE 1-1/4 lbs.00112 AFF-346 FF-346 F56 A39-FO 6 x 1/2 H.R. 1-1/4 lbs.00179 AMF-346 MF-346 M56 A39-M0 ALUMINUM 1-1/4 lbs.00042 ACF-346 CF-346 C56 A39-CO OXIDE 1-1/4 lbs.00113 AFF-356 FF-336 F38 A40-FO 6 x 5/8 H.R. 1-7/8 lbs.00180 AMF-356 MF-356 M58 A40-MO ALUMINUM 1-7/8 lbs.00043 ACF-356 CF-356 C58 A40-CO OXIDE 1-7/8 lbs.00114 AFF-366 FF-366 F60 A41-FO 6 x 3/4 H.R. 2-3/8 lbs.00181 AMF-366 MF-366 M60 A41-MO ALUMINUM 2-3/8 lbs.00044 ACF-366 CF-366 C60 A41-CO OXIDE 2-3//8 lbs.00301 FSF-376 F61 C42-F 6 x 1H.R. 4-5/8 lbs.00416 MSF-376 N.A. M61 C42-M SILICON 4-5/8 lbs.00255 CSF-376 C61 C42-C CARBIDE 4-5/8 lbs.00115 AFF-376 FF-376 F62 A42-FO 6 x 1H.R. 4-5/8 lbs.00182 AMF-376 MF-376 M62 A42-MO ALUMINUM 4-5/8 lbs.00045 ACF-376 CF-376 C62 A42-CO OXIDE 4-5/8 lbs.

Tool Room And Die Finishing Stones

F = Fine M = Medium C = Coarse

Bkn. Pkg. = 1-4Min. Pkg. = 5Std. Pkg. = 20

17612_Sticks_P1_10 7/20/05 2:13 PM Page 9

10

Aluminum Oxide

UPC Code # Sticks & Norton Carbo Bay State Weight Per Stone Size730006 Stones # # # # Std. Pkg. and Shape

00120 AFF-444 FF-444 300A A246-FO 7 oz. 4 x 1/2 x 1/1600187 AMF-444 MF-444 301A A246-MO 7 oz.00050 ACF-444 CF-444 302A A246-CO 7 oz. FLAT00123 AFF-474 FF-474 303A A248-FO 12 oz. 4 x 1/2 - 1/4 x 5/16 -1/8.00190 AMF-474 MF-474 304A A248-MO 12 oz.00053 ACF-474 CF-474 305A A248-CO 12 oz. FLAT DOUBLE TAPERED00116 AFF-414 FF-414 306A A242-FO 7 oz. 4 x 5/16 x 3/16 - 1/1600183 AMF-414 MF-414 307A A242-MO 7 oz.00046 ACF-414 CF-414 308A A242-CO 7 oz. FLAT TAPERED00122 AFF-464 FF-464 309A A249-FO 12 oz. 4 x 1/2 - 1/4 x 5/16 - 1/800189 AMF-464 MF-464 310A A249-MO 12 oz.00052 ACF-464 CF-464 311A A249-CO 12 oz. OVAL DBL. TAPERED00121 AFF-454 FF-454 312A A247-FO 7 oz. 4 x 1/2-3/16 x 3/16-1/1600188 AMF-454 MF-454 313A A247-MO 7 oz.00051 ACF-454 CF-454 314 A A247-CO 7 oz. OVAL BDL. TAPERED00117 AFF-424 FF-424 315A A243-FO 6 oz. 4 x 3/8-3/16 x 1/8-1/16.00184 AMF-424 MF-424 316A A243-MO 6 oz.00047 ACF-424 CF-424 317A A243-CO 6 oz. OVAL DBL. TAPERED00119 AFF-434 FF-434 318A A245-FO 11 oz. 4 x 7/16 x 3/16 x 1/800186 AMF-434 MF-434 319A A245-MO 11 oz.00049 ACF-434 CF-434 320A A245-CO 11 oz. OVAL FLAT TAPER SIDES00118 AFF-433 FF-433 321A A244-FO 10 oz. 3-1/2 x 7/16 x 3/1600185 AMF-433 MF-433 322A A244-MO 10 oz.00048 ACF-433 CF-433 323A A244-CO 10 oz. OVAL

Specialty Shapes – Aluminum Oxide

00125 AFF-644 FF-644 334A A240-FO 15 oz. 4 x 1/2 x 1/400192 AMF-644 MF-644 335A A240-MO 15 oz.00055 ACF-644 CF-644 336A A240-CO 15 oz. TAPERED ROUND00124 AFF-544 FF-544 337A A241-FO 10 oz. 4 x1/2 x 1/400191 AMF-544 MF-544 338A A241-MO 10 oz.00054 ACF-544 CF-544 339A A241-CO 10 oz. TAPERED TRIANGLE00141 AFT-134 FT-134 340A A250-FO 10 oz. 4 x 9/16 x 3/1600212 AMT-134 MT-134 341A A250-MO 10 oz.00068 ACT-134 CT-134 342A A250-CO 10 oz. DIAMOND00126 AFF-723 FF-723 97A A251-FO 7 oz. 3 x 5/16 BASE00193 AMF-723 MF-723 98A A251-MO 7 oz.00056 ACF-723 CF-723 99A A251-CO 7 oz. TAPERED POINT00127 AFF-724 FF-724 N.A. A252-FO 13 oz. 4 x 1 x 1/8 BACK00194 AMF-724 MF-724 N.A. A252-MO 13 oz.00057 ACF-724 CF-724 N.A. A252-CO 13 oz. KNIFE STONE00137 AFT-123 FT-123 N.A. A254-FO 1 lb. 3-1/2 x 3/4 x 3/1600208 AMT-123 MT-123 N.A. A254-MO 1 lb.00064 ACT-123 CT-123 N.A. A254-CO 1 lb. REAMER STONE00138 AFT-124 FT-124 294F A255-FO 2-3/4 lbs. 4-1/2 x 1 x 5/1600209 AMT-124 MT-124 294M A255-MO 2-3/4 lbs.00065 ACT-124 CT-124 294C A255-CO 2-3/4 lbs. REAMER STONE00139 AFT-125 FT-125 N.A. A256-FO 1-7/8 lbs. 5 x 1 x 3/1600210 AMT-125 MT-125 N.A. A256-MO 1-7/8 lbs.00066 ACT-125 CT-125 N.A. A256-CO 1-7/8 lbs. REAMER STONE00140 AFT-126 FT-126 N.A. A257 -FO 3 lbs. 6 x 1 x 1/400211 AMT-126 MT-126 N.A. A257-MO 3 lbs.00067 ACT-126 CT-126 N.A. A257-CO 3 lbs. REAMER STONE00134 AFT-10 FT-10 18FT A260-FO 12 oz. 4'' LONG00204 AMT-10 MT-10 18M A260-MO 12 oz.

AUGER BIT STONE

Silversmiths’ StonesBroken Pkg. = 1-4 Minimum Pkg. = 5 Standard = 20

17612_Sticks_P1_10 7/20/05 2:14 PM Page 10

Round Edge Slip StonesF = Fine M = Medium C = Coarse

Arkansas Round Edge Slip StonesHard and Soft Arkansas

00344 HAS-3 HS-3 3 x 1-3/4-2 x 1/4-3/8 x 1/16-1/8 HardBkn.=1-4

1-1/2 lbs.

00345 HAS-4 HS-4 4 x 1-3/4-2 x 3/8-1/2 x 1/8-3/16 HardMin.=5

2-1/2 lbs.

00347 HAS-14 HS-14 4 x 1-1/4-1-1/2 x 1/4-3/8 x 1/8 Sharp EdgeStd.=10

1-3/8 lbs.

00445 SAS-4 SS-4 4 x 1-3/4-2 x 3/8-1/2 x 1/8-3/16 Soft 2 lbs.

UPC Code # Sticks & Stones Norton Carbo. Bay State Size Packaging Weight Per 730006 # # # # Std. Pkg.

00306 FSS-10 N.A. 445F N.A. 4 x 1 x 1/8 x 3/16

00421 MSS-10 N.A. 445M N.A. SILICON CARBIDE 1 lb.

00307 FSS-14 N.A. 186 N.A. 4 x 1 x 7/16 x 3/16

00422 MSS-14 N.A. 187 N.A. SILICON CARBIDE 1-3/8 lbs.

00128 AFS-14 FS-14 N.A. A45-FO 4 x 1 x 7/16 x 3/16

00196 AMS-14 MS-14 N.A. A45-MO ALUMINUM OXIDE 1-3/8 lbs.

00308 FSS-24 FJS-24 177 C46-F

00423 MSS-24 MJS-24 178 C46-M 4-1/2 x 1-3/4 x 1/4 x 1/16 1-3/8 lbs.

00258 CSS-24 CJS-24 179 C46-C SILICON CARBIDE

00130 AFS-24 FS-24 N.A. A46-FO

00199 AMS-24 MS-24 N.A. A46-MO 4-1/2 x 1-3/4 x 1/4 x 1/16 1-3/8 lbs.

00059 ACS-24 CS-24 N.A. A46-CO ALUMINUM OXIDE

00131 AFS-34 FS-34 N.A. A47-FO Bkn. = 1-4

00201 AMS-34 MS-34 N.A. A47-MO 4-1/2 x 1-3/4 x 3/8 x 1/8 Min. = 5 2 lbs.

00060 ACS-34 CS-34 N.A. A47-CO ALUMINUM OXIDE Std. = 10

00311 FSS-44 FJS-44 183 C48-F

00424 MSS-44 MJS-44 184 C48-M 4-1/2 x 1-3/4 x 1/2 x 3/16 2-1/2 lbs.

00259 CSS-44 CJS-44 185 C48C SILICON CARBIDE

00132 AFS-44 FS-44 N.A. A48-FO

00203 AMS-44 MS-44 N.A. A48-MO 4-1/2 x 1-3/4 x 1/2 x 3/16 2-1/2 lbs.

00061 ACS-44 CS-44 N.A. A48-CO ALUMINUM OXIDE

00426 MSS-54 MJS-54 181 C49-M 4-1/2 x 2-1/8 x 5/8 x 5/16 3-1/4 lbs.

00129 AFS-15 FS-15 293F A50-FO 5 x 1 x 5/16 x 3/32

00197 AMS-15 MS-15 293M A50-MO ALUMINUM OXIDE 1-1/8 lbs.

00313 FSS-66 FJS-66 174 C51-F

00427 MSS-66 MJS-66 175 C51-M 6 x 2-1/4 x 3/4 x 3/8 5-3/4 lbs.

00261 CSS-66 CJS-66 176 C51-C SILICON CARBIDE

Hard Arkansas Carving Tools00346 HAS-12 HS-12 2-1/4 x 7/8 x 3/16 Round Edge Double Angle

Bkn.=1-412 oz.

00348 HAS-22 HS-22 2-1/4 x 7/8 x 3/16 Round Edge Single AngleMin.=5

12 oz.

00349 HAS-32 HS-32 2-1/4 x 7/8 x 3/16 Square Edge Double AngleStd.=10

12 oz.

00350 HAS-42 HS-42 2-1/4 x 7/8 x 3/16 Square Back Knife Blade 8 oz.

Hard Arkansas Jewelers Stone & Penknife PiecesAnd Soft Arkansas Penknife Pieces

00323 HAB-24 HB-24 4 x 2 x 3/8-1/2 Jewelers Stone Min. = 1, Std. = 5 2 lbs.

00321 HAB-13 HB-13 3 x 1 x 1/4-3/8 Penknife Piece Min. = 5, Std. = 10 1-1/4 lbs.

00322 HAB-14 HB-14 4 x 1 x 1/4-3/8 Penknife Piece Min. = 5, Std. = 10 1-3/4 lbs.

00438 SAB-13 SB-13 3 x 1 x 1/4-3/8 Soft Penknife Piece Min. = 5, Std. = 10 1-1/4 lbs.

00439 SAB-14 SB-14 4 x 1 x 1/4-3/8 Soft Penknife Piece Min. = 5, Std. = 10 1-3/4 lbs.

11

17612_Sticks_P11_20 8/3/05 12:52 PM Page 11

Aluminum Oxide Engravers Pencils

UPC Code # Sticks & Stones Norton Size and Description Packaging Weight Per 730006 # # Std. Pkg.

00357 HIT-17 IT-17 7" Long Pencil w/1/8" square India Stone Min. = 5, Std. = 10 14 oz.

Engravers Chuck and Points

12

00469 SSXT-1 XT-1 Chuck Only Min. = 5, Std. = 10 6 oz.

00135 AFT-11 FT-11 1 x 1/8 Round FIne Aluminum Oxide B = 1, M = 5 S = 20 3 oz.

Arkansas Bench Stones – Hard & Soft00318 HAB-4 HB-4 4 x 2 x 3/4-1 Hard Bench Stone Min. = 1, Std. = 5 3 lbs.

00319 HAB-6 HB-6 6 x 2 x 3/4-1 Hard Bench Stone Min. = 1, Std. = 5 4-3/4 lbs.

00320 HAB-8 HB-8 8 x 2 x 3/4-1 Hard Bench Stone Min. = 1, Std. = 5 6-1/4 lbs.

00435 SAB-4 SB-4 4 x 2 x 3/4-1 Soft Bench Stone Min. = 1, Std. = 5 3 lbs.

00436 SAB-6 SB-6 6 x 2 x 3/4-1 Soft Bench Stone Min. = 1, Std. = 5 4-3/4 lbs.

00437 SAB-8 SB-8 8 x 2 x 3/4-1 Soft Bench Stone Min. = 1, Std. = 5 6-1/4 lbs.

Arkansas Square and Triangle Files00326 HAF-13 HF-13 3-3-1/2 x 1/4 Square B = 1, M = 5 S = 10 4 oz.

00327 HAF-33 HF-33 3-3-1/2 x 3/8 Square B = 1, M = 5 S = 10 9 oz.

00328 HAF-43 HF-43 3-3-1/2 x 1/2 Square B = 1, M = 5 S = 10 14 oz.

00329 HAF-113 HF-113 3-3-1/2 x 1/4 Triangle B = 1, M = 5 S = 10 3 oz.

00330 HAF-133 HF-133 3-3-1/2 x 3/8 Triangle B = 1, M = 5 S = 10 5 oz.

00331 HAF-143 HF-143 3-3-1/2 x 1/2 Triangle B = 1, M = 5 S = 10 7 oz.

Mounted Arkansas Bench Stones in Box – Hard & Soft00340 HAM-4 HM-4 4 x 1-7/8 Hard Mounted Bench Stone Min. = 1, Std. = 5 3 lbs.

00341 HAM-6 HM-6 6 x 1-7/8 Hard Mounted Bench Stone Min. = 1, Std. = 5 5-3/4 lbs.

00342 HAM-8 HM-8 8 x 1-7/8 Hard Mounted Bench Stone Min. = 1, Std. = 5 7-3/4 lbs.

00440 SAM-3 SM-3 3-1/2 x 1 Soft Mounted Bench Stone Min. = 1, Std. = 5 1-1/4 lbs.

00441 SAM-4 SM-4 4 x 1-7/8 Soft Mounted Bench Stone Min. = 1, Std. = 5 3 lbs.

00442 SAM-6 SM-6 6 x 1-7/8 Soft Mounted Bench Stone Min. = 1, Std. = 5 5-3/4lbs.

00443 SAM-8 SM-8 8 x 1-7/8 Soft Mounted Bench Stone Min. = 1, Std. = 5 7-3/4lbs.

17612_Sticks_P11_20 7/20/05 2:03 PM Page 12

13

Special Shaped Arkansas Files – Hard Only

UPC Code # Sticks & Stones Norton Size and Description Packaging Weight Per 730006 # # Std. Pkg.

00332 HAF-813 HF-813 3-3-1/2 x 1/4 x 5/16 Round B = 1, M = 5 S = 10 5 oz.

00333 HAF-823 HF-823 3-3-1/2 x 3/8-1/2 x 1/8-3/16 Flat B = 1, M = 5 S = 10 6 oz.

00334 HAF-833 HF-833 3-3-1/2 x 3/8-1/2 x 1/8-3/16 Bevel B = 1, M = 5 S = 10 6 oz.

00335 HAF-843 HF-843 3-3-1/2 x 1/2 x 3/16-1/4 Diamond B = 1, M = 5 S = 10 5 oz.

00336 HAF-853 HF-853 3-3-1/2 x 1/2 x 3/16-1/4 Oval B = 1, M = 5 S = 10 6 oz.

00337 HAF-863 HF-863 3-3-1/2 x 1/4 Base - Point B = 1, M = 5 S = 10 3 oz.

00338 HAF-873 HF-873 3-4 x 3/4-1 x 1/8-1/4 Knife Blade B = 1, M = 5 S = 10 7 oz.

Jointer Stones

UPC Code # Sticks & Stones Norton Carbo. Bay State Size Packaging Weight Per 730006 # # # # Std. Pkg.

00456 SE-64 JE-54 425 C-149 1/4 x 3/4 x 4 B = 1, M = 5 S = 10 1 lb.

00457 SE-64 JE-64 428 C-150 5/16 x 3/4 x 4 B = 1, M = 5 S = 10 1 lb.

00458 SE-74 JE-74 390 C-151 3/8 x 3/4 x 4 B = 1, M = 5 S = 10 1-1/2 lbs.

00459 SE-84 JE-84 373 C-152 1/2 x 3/4 x 4 B = 1, M = 5 S = 10 1-1/2 lbs.

00460 SE-104 JE-104 391 C-153 3/4 x 3/4 x 4 B = 1, M = 5 S = 10 2-1/8 lbs.

00071 AE-54 IE-54 425 A-149-O 1/4 x 3/4 x 4 B = 1, M = 5 S = 10 1 lb.

00072 AE-64 IE-64 428 A-150-O 5/16 x 3/4 x 4 B = 1, M = 5 S = 10 1 lb.

00073 AE-74 IE-74 426 A-151-O 3/8 x 3/4 x 4 B = 1, M = 5 S = 10 1-1/2 lbs.

00074 AE-84 IE-84 438 A-152-O 1/2 x 3/4 x 4 B = 1, M = 5 S = 10 1-1/2 lbs.

00075 AE-104 IE-104 440 A-153-O 3/4 x 3/4 x 4 B = 1, M = 5 S = 10 2-1/8 lbs.

Pocket Stone With Plastic PouchMedium Grit (220) Silicon Carbide

00368 JP-14 JP-14 149 N.A. 3 x 7/8 x 3/8 M = 1, S = 10 1-1/2 lbs.

Medium Silicon Carbide (220) Pocket Stones00463 SJP-13 JP-14 149 N.A. 3 x 7/8 x 3/8 Med. S/C M = 1, S = 10 1-1/4 lbs.

00315 GSHH-13 CG220-PV 39 3/8 x 3/16 x 4-3/16 Green S/C Sold in brackets 50 = 7-1/2 lbs.

00316 GSHH-14 CG280/320-PV 38 3/8 x 3/16 x 4-3/16 Green S/C Sold in brackets 50 = 7-1/2 lbs.

00317 GSHH-15 CG400-PV 37 3/8 x 3/16 x 4-3/16 Green S/C Sold in brackets 50 = 7-1/2 lbs.

Jointer Stones provide a fast methodof restoring and maintaining thecutting edges of mechanical jointingdevices on automatic planers

This world renowned hand hone of Norton Green Crystolon is the most famoussharpening stone known to industry.

Available in Three Grit Sizes, 220 – 280/320 and 400.

17612_Sticks_P11_20 7/20/05 2:03 PM Page 13

14

Molded Boat Rubs

Aluminum Oxide (India)Gouge Sharpening Stone

UPC Code # Sticks & Stones Norton Carbo. Bay State Size Packaging Weight Per 730006 # # # # Std. Pkg.

00133 AFS-76 FS-76 15 A115-FO 6 x 2 x 1 x 1/2 x 3/8 B = 1, M = 5, S = 10 5-3/4 lbs.

The Gouge Stone is indespens-able for the tools of the artist,craftsman and woodworkers.Designed for curved edge tools.

Aluminum Oxide (India)Carving Slips

00195 AMS-12 MS-12 N.A. A82-MO 2-1/4 x 7/8 x 3/16 B = 1, M = 5, S = 20 13 oz.

00198 AMS-22 MS-22 N.A. A83-MO 2-1/4 x 7/8 x 3/16 B = 1, M = 5, S = 20 11 oz.

00200 AMS-32 MS-32 N.A. A84-MO 2-1/4 x 7/8 x 3/16 B = 1, M = 5, S = 20 10 oz.

00202 AMS-42 MS-42 N.A. A81-MO 2-1/4 x 7/8 x 3/16 B = 1, M = 5, S = 20 8 oz.

Carving Tool Slips are excellentfor final finish on all carvingtools. The extreme hardnessgives long life. Medium Grit only.

Silicon Carbide Hand HonesCarving Tool Slips are excellent for final finish on all carving tools. Theextreme hardness gives long life. Medium Grit only.

00314 FST-63 FJT-63 F33 C237 3-1/2 x 3/4 x 1/2 B = 1, M = 5, S = 20 2 lbs.

00428 MST-63 MJT-63 M33 C238 3-1/2 x 3/4 x 1/2 B = 1, M = 5, S = 20 2 lbs.

00262 CST-63 CJT-63 C33 C239 3-1/2 x 3/4 x 1/2 B = 1, M = 5, S = 20 2 lbs.

General Purpose File

00473 ST-911 JT-911 198 C253 9-1/2 x 1-3/8 x 1/2 M = 1, S = 10 5 lbs.

The right size and shape toallow widespread use on avariety of home and gardentools.

Utility Files

00454 SD-2 JD-2 57 C5 14" Overall B = 1, M = 5, S = 10 12-1/2 lbs.

00455 SD-3 JD-3 75 N.A. 14" Overall B = 1, M = 5, S = 10 12-1/2 lbs.

SD-3 Combination, Coarse/FineSD-2 Medium, Single Grit

UPC Code # Size and Description Grit730006

* 1-1/2 x 2-3/8 x 9 Aluminum Oxide 60 & 80 See Price Book

* 1-1/2 x 2-3/8 x 9 Silicon Carbide 46 & 80 See Price Book

17612_Sticks_P11_20 7/20/05 2:03 PM Page 14

15

Carving Knife SharpenerSharpener is medium grit, reinforced with steel rod.

UPC Code # Sticks & Stones Norton Carbo. Size and Description Packaging Weight Per 730006 # # # Std. Pkg.

00467 SKPT-2 KPT-2 76 13-3/4" O/A with Handle B = 1, M = 5, S = 20 11 lbs.

Kitchen Knife SharpenerFor all kitchen knives, fine grit.

00433 S273A 273A 66 7-1/2" O/A with Handle M = 1, S = 10 3 lbs.

Home and Garden SharpenerOne flat side, one convex, ideal for all garden tools.

00466 SJT-8 JT-8 46 10-1/2" O/A with Handle B = 1, M = 5, S = 20 10 lbs.

00451 SB-74 JB-74 289 4" Dia. x 1-1/2" Thick M = 1, S = 5 6-1/4 lbs.

Combination Axe StoneThe Combination Axe Stone is the best tool for axe & hatchetsharpening, coarse/fine, lubricate with oil.

00465 SJT-3 JT-3 196 C-120 3" Dia. x 5/8" Thick M = 1, S = 10 3 lbs.

Scythe StonesAluminum Oxide = ATD-1Silicon Carbide = TS-3

Made for scythes, sickles and mowing machines.

Tradesmen’s StonesFor sharpening of knives for trimming leather, rubber,plastic and carpet. ST-930 is combination, ST-920 issingle grit medium, ST-910 no handle.

00214 ATD-1 TD-1 188 10 x 1-5/16 x 3/4 B = 1, M = 5, S = 10 8 lbs.

00481 TS-3 TJ-3 192 10 x 1-1/4 x 3/4 B = 1, M = 5, S = 10 8 lbs.

Machine Knife StoneThe Machine Knife Stone is for the sharpening and honing ofpaper, cloth and veneer knives while on the machine. No needto remove the knives from the machine until in need of amajor re-grind. Each stone has a finger groove to providesafety.

Oil filled combinatian grit.

00475 ST-930 JT-930 75 14-3/4" O/A with Handle B = 1, M = 5, S = 10 9 lbs.

00474 ST-920 JT-920 129 14-3/4" O/A with Handle B = 1, M = 5, S = 10 9 lbs.

00472 ST-910 JT-910 N.A. 10 x 1-1/4 x 3/4 B = 1, M = 5, S = 10 7 lbs.

17612_Sticks_P11_20 7/20/05 2:03 PM Page 15

16

Wheel DresserThe Wheel Dresser is widely used to clean, true andshape the face of a grinding wheel, used with the ST-246Dressing Stick below.

Dressing SticksDressing Sticks are commonly used by hand or in theHD-6 above. Used to clean, true or form the face of agrinding wheel.

UPC Code # Sticks & Stones Norton Carbo. Size and Description Packaging Weight Per 730006 # # # Std. Pkg.

00354 HD-6 H-6 55 10" O/A with Handle B = 1, M = 5, S = 10 5-5/8 lbs.

00470 ST-246 JT-246 56 1/2" Round x 6" Long B = 1, M = 5, S = 10 1 lb.

00471 ST-276 JT-276 N.A. 1" Round x 6" Long B = 1, M = 5, S = 10 3-5/8 lbs.

Cutlery Bench StonesGiant Combination

Fine & Coarse in metal box.

UPC Code # Sticks & Stones Size and Description Packaging Weight Per 730006 # Std. Pkg.

00360 IM-11 Stone w/box 11-1/2 x 2-1/2 x 1 Coarse & Fine A/O M = 1, S = 2 10 lbs.

00358 IM-2 Stone only 11-1/2 x 2-1/2 x 1 Coarse & Fine A/O M = 1, S = 2 5 lbs.

00373 JUM-22 Stone w/box 11-1/2 x 2-1/2 x 1 Coarse & Fine S/C M = 1, S = 2 10 lbs.

00371 JUM-3 Stone only 11-1/2 x 2-1/2 x 1 Coarse & Fine S/C M = 1, S = 2 5 lbs.

00372 JUM-4 Stone only 1/2 x 2-1/2 x 1-1/2 Coarse & Fine S/C M = 1, S = 2 7 lbs.

00356 HIB-27 Stone w/box 7 x 2 x 1 Fine A/O & Hard Arkansas M = 1, S = 2 5 lbs.

00462 SIB-27 Stone w/box 7 x 2 x 1 Medium A/O & Soft Arkansas M = 1, S = 2 5 lbs.

00476 SXT-4 Bench Stone Box for all 4 x 2 x 1 Stones Sold in brackets *

00477 SXT-6 Bench Stone Box for all 6 x 2 x 1 Stones Sold in brackets *

00478 SXT-8 Bench Stone Box for all 8 x 2 x 1 Stones Sold in brackets *

Crystolon Cutlers StoneCoarse & Fine combination stone only

Wood Boxes OnlyFor use with any stone you prefer.

Reversible Oil Stone in Beautiful HingedWood Box with Latch

17612_Sticks_P11_20 7/20/05 2:03 PM Page 16

17

S&S Burr BreakerThe perfect, lowest cost method of removing burrs frommagnetic chucks and for scouring any flat metal surface.

Blanchard “Burr Busters”For use in removing burrs on magnetic chucks orscouring any flat surface.

Aluminum Oxide/ Soft Arkansas ComboA unique combination stone made by bonding a coarsealuminum oxide stone and a soft Arkansas stonetogether.

UPC Code # Sticks & Stones Size One Specification Only Sold in Quantity Brackets730006

* Burr Breaker 1-5/8 x 4 x 4 Standard 1 - 3 - 10 - 25+

UPC Code # The Blanchard Size One Specification Only Sold in Quantity Brackets730006 Company

00524 Burr Buster 1-9/16 x 4-3/8 x 6 Standard 1 - 5 - 10

00461 SIB-6 Stone only 6 x 2 x 1 Coarse A/O & Soft Arkansas Comb. M = 1, S = 5 6 lbs.

Norton Multi-Oilstone UnitsThe Norton Multi-Oilstone is the most popular choiceof commercial kitchens across the country. For com-plete sharpening of all cutlery. This combination ofthree oil filled, reversible stones includes coarse

Crystolon, medium Crystolon, and precision sharpening fine India stones. The two sides not in use are immersed inoil. There is a heavy non-skid base with suction cup foot-pieces. Unit comes with one pint of Norton Bear Brandsharpening oil. Replacement parts are available on request.

UPC Code # Sticks & Stones Size and Description Weight Per Std. Pkg. Packaging73006

00363 IM-313 5-1/2 x 6 x 16 13 lbs. Standard = 1

00362 IM-100 4 x 4 x 9-1/2 3 lbs. Standard = 1

00351 HR-115 11-1/2 x 2-1/2 x 1/2 Hard Arkansas 1-1/4 lbs. Standard = 1

00359 IM-9 11-1/2 x 2-1/2 x 1/2 Fine India 3 lbs. M = 1, S = 2

00365 JM-6 11-1/2 x 2-1/2 x 1/2 Medium S/C 3 lbs. M = 1, S = 2

00364 JM-3 11-1/2 x 2-1/2 x 1/2 Coarse S/C 3 lbs. M = 1, S = 2

00468 SR-115 11-1/2 x 2-1/2 x 1/2 Soft Arkansas 1 lb. S = 1

03000 HR-26 6 x 2 x 1/2 Hard Arkansas 3 lbs. M = 1, S = 5

00361 IM-91 6 x 2 x 1/2 Fine India 3 lbs. M = 1, S = 5

00367 JM-61 6 x 2 x 1/2 Medium S/C 3 lbs. M = 1, S = 5

00366 JM-31 6 x 2 x 1/2 Coarse S/C 3 lbs. M = 1, S = 5

03001 SR-26 6 x 2 x 1/2 Soft Arkansas 3 lbs. M = 1, S = 5

Replacement Stones

17612_Sticks_P11_20 7/20/05 2:04 PM Page 17

18

Griddle BricksGriddle Bricks – The sanitary method of cleaning and scouring griddlesand cooking plates. Faster, easier, as well as cleaner and less expensivethan all other methods. Rounded edges for comfortable hand grip. Not oilfilled. Available only in medium grit. Sold in quantity brackets found inprice book.

UPC Code # Sticks & Stones Norton Carbo. Bay State Size Weight Per730006 # # # # Stone

00142 AIT-4 IT-4 217 A-201 4-1/2 x 3 x 2 1-3/4 lbs.

Rubbing Brick with HandleHand Rubs with plastic handles make quick work of removing moldmarks, rubbing down green concrete and are ideal for floor, overheadand wall work. Concrete workers and masons appreciate the handlewhich reduces fatigue. Extra coarse.

Rubbing Bricks – Plain & FlutedSilicon carbide rubbing bricks without handles are available in two types,plain and fluted. Plain rubs are the choice of machinists and foundrymen fordressing grinding wheels and cleaning and scouring castings. Fluted rubsare used in concrete applications for rubbing down green concrete to removemold marks. The diagonal flutes provide shearing action and carry awaydebris. Sold in quantity brackets.

UPC Code # Sticks & Stones Norton Industry Size Weight Per730006 # # # Stone

00516 SHR-250 235 HR-250 8 x 3-1/2 x 1-1/2 1-3/4 lbs.

00517 SHR-252 BFH-6 HR-252 6 x 3 x 1 1-1/4 lbs.

UPC Code # Sticks & Stones Industry Size Type Weight Per730006 # Stone

00498 SHR-201/BP-14 HR-201 4 x 2 x 1 Plain 3/4 lbs.

00499 SHR-202/BP-24 HR-202 4 x 2 x 2 Plain 1-1/3 lbs.

00502 FR510/SHR-211/BP-16 HR-211 6 x 2 x 1 Plain 1 lb.

00503 SHR-213/BP-26 HR-213 6 x 2 x 2 Plain 2-1/4 lbs.

00507 FR520/SHR-222/BP-18 HR-222 8 x 2 x 1 Plain 1-3/4 lbs.

00508 SHR-225/BP-28 HR-225 8 x 2 x 2 Plain 2-3/4 lbs.

00512 SHR-241/BF-26 HR-241 6 x 2 x 2 Fluted 2 lbs.

00513 SHR-242/BF-28 HR-242 8 x 2 x 2 Fluted 2-1/2 lbs.

Half Round Foundry Core Files

UPC Code # Product Number A Dimension L Dimension Overall730006 Length End Size

02370 #25 Half Round 3-3/4" 6" 8" Large 7/16 x 7/8, Small 5/16 x 5/8

02371 #26 Half Round 5-1/4" 8" 11" Large 15/32 x 15/16, Small 11/32 x 11/16

02372 #27 Half Round 6-3/4" 10" 13" Large 17/32 x 1-1/16, Small 3/8 x 3/4

02373 #28 Half Round 8-1/4" 12" 15" Large 19/32 x 1-3/16, Small 7/16 x 7/8

17612_Sticks_P11_20 7/20/05 2:04 PM Page 18

19

Flat Core Files with Plastic HandlesFiberglass Reinforced – S/C Resin Bond

Lower cost flat core files are available in any size desired. They are centrally reinforced with fiberglassto retard breakage. Made of resin bond silicone carbide abrasive in a very coarse grit to aggressivelyfile sand cores.They are custom made to any size required, but come in a number of standard sizes asfollows:

Standard Size List

1/8 x 1/2 x 8 1/4 x 1 x 12 1/2 x 1 x 121/8 x 1 x 9 1/4 x 2 x 12 1/2 x 2 x 101/8 x 1 x 12 1/2 x 1 x 9 1/2 x 2 x 121/4 x 1 x 9 1/2 x 1 x 10

Flat core files are much more economical to use than the metal tang type, half round core filesmentioned earlier. Big savings are available by using this type file. All are made from a very coarse gritsilicon carbide abrasive of a very hard resin bond for long life and aggressive cut.

Jointer & Pattern StonesWe custom manufacture jointer and pattern stones for all applications. We stock slabs from which wecut all sizes and specifications used in joining and molding manufacturing. We make any size, abrasivetype, grit size and hardness from slabs which are in stock. Lead time is only three weeks. Standard sizelist as follows:

Standard Size List

1/4 x 3/4 x 4 5/16 x 3/4 x 4 3/8 x 3/4 x 4 1/2 x 3/4 x 43/4 x 3/4 x 4 3/4 x 2 x 4 3/4 x 2 x 6 3/4 x 2 x 8.590 x 2 x 6 .590 x 2-1/4 x 6 .590 x 2 x 6 .590 x 2-1/4 x 8

Molding and pattern stones are available in superfine grit down to 1200.

Dressing SticksFor Vitrified Grinding Wheels - Stock Sizes

1/2 x 1/2 x 6 C24-RV 3/4 x 3/4 x 6 C24-RV 3/4 x 3/4 x 8 C24-RV1 x 1 x 6 C24-RV 1 x 2 x 6 C24-RV 1 x 1 x 8 C24-RV

1/2 x 1 x 6 C24-RV 2 x 2 x 8 C24-RV 1 x 2 x 8 C24-RV2 x 2 x 6 C24-RV 1 x 1 x 6 C46-RV 1/2 x 6 RD. C24-RV1 x 6 RD. C24-RV 1 x 1 x 8 C46-RV

For Diamond & CBN Wheels - Stock Sizes

1/2 x 1/2 x 6 38A150-IVBE 1/2 x 1/2 x 6 x 38A220-IVBE3/4 x 3/4 x 4 38A150-IVBE 3/4 x 3/4 x 4 x 38A220-IVBE

1 x 1 x 6 38A150-IVBE 1 x 1 x 6 x 38A220-IVBEMany other sizes are available but may be limited in stock. Please call our excellent customer servicestaff for custom sizes, specifications and recommendations.

17612_Sticks_P11_20 7/20/05 2:04 PM Page 19

20

Mold & Diemakers Polishing Stones

Availability Chart

Pencil Stones5/32 x 5/32 x 4

PSA PSR PSO PSE

Diemaker Resin Bonded Oil Treated EDM StoneAlum. Oxide Alum. Oxide Alum. Oxide Premium A/OMedium Hard Extra Hard Hard HardWhite To Tan Dark Brown Cream Color Salmon Color

Grit Price Grit Price Grit Price Grit Price

150 180 120 120

220 220 220 150

320 320 320 180

400 400 400 220

500 600 600 320

600 N.A. N.A. 400

800 N.A. N.A. 500

900 N.A. N.A. 600

Series Type Description

D Diemaker Medium Hard Regular Aluminum Oxide, for fast cutting action, for general polishing.

M Moldmaker Solft Silicon Carbide, non loading with even breakdown readily conforms to shape fo work surface.

EDM EDM Special Aluminum Oxide for use on electrical discharge machining surfaces.

HM Hard Moldmaker Medium Hard Silicon Carbide for general polishing.

SF Super Fine Calcined Alumina with a soft bond, 900 grit only, for superfinishing applications.

B Resin Bond Very Hard Aluminum Oxide for fine detail work, holds shape and produces a fine finish.

OT Hard Polishing Premium Aluminum Oxide in a hard bond, holds shape for polishing ribs, slots & etc., oil treated.

WT General PolishingPremium Aluminum Oxide in a medium hard bond for general polishing, wax treated for loadresistance.

R Ruby Aluminum Oxide with a soft bond for fast stock removal.

Diemaker StonesGeneral Purpose Alum. Oxide, Medium Hard, White to Tan

Size 100 150 220 320 400 500 600 900

1/4" RD. x 6

3/8" RD. x 6

1/2" RD. x 6

1/16 x 1/4 x 6

1/8 x 1/4 x 6

1/4 x 1/4 x 6

3/8 x 3/8 x 6

1/16 x 1/2 x 6

1/8 x 1/2 x 6

1/4 x 1/2 x 6

1/2 x 1/2 x 6

1/4 x 1 x 6

1/8 x 1 x 6

1/4 x 3/4 x 6

1/2 x 1 x 6

1 x 1 x 6

All sizes in all grits available

17612_Sticks_P11_20 7/20/05 2:04 PM Page 20

21

Stone Size 150 220 320 400 500 600

1/4" RD. x 63/8" RD. x 61/2" RD. x 6

1/16 x 1/4 x 61/16 x 1/2 x 61/8 x 1/4 x 61/8 x 1/2 x 61/8 x 1 x 6

3/16 x 1/2 x 61/4 x 1/4 x 61/4 x 1/2 x 61/4 x 1 x 6

3/8 x 3/8 x 61/2 x 1/2 x 63/4 x 3/4 x 6

1 x 1 x 6

Grit

All sizes in all gritsavailable

Stone Size 100 120 150 180 220 320 400 500 600

1/16 x 1/4 x 61/16 x 1/2 x 61/8 x 1/8 x 61/8 x 1/4 x 61/8 x 1/2 x 63/16 Sq. x 61/4 x 1/4 x 61/4 x 1/2 x 63/8 x 3/8 x 6

1 x 1 x 61/4 Rd. x 6

Grit

All sizes in all gritsavailable

Moldmaker StonesSoft Silicon Carbide Vitrified, Green, Gray, Black

All are custom made and have no UPC code numbersRounds are considered specials and may require long lead time.

EDM StonesHard Premium Aluminum Oxide, Vitrified Bond, Salmon Color

Stone Size 46 60 80 100 150 220 320 400 500 600

1/16 x 1/4 x 61/16 x 1/2 x 61/8 x 1/4 x 61/8 x 1/2 x 61/8 x 1 x 6

1/4 x 1/4 x 61/4 x 1/2 x 61/4 x 1 x 6

3/8 x 3/8 x 61/2 x 1/2 x 63/4 x 3/4 x 6

1 x 1 x 6

Grit

All sizes in all gritsavailable

Stone Size Price Each

1/8 x 1/4 x 61/4 x 1/4 x 61/8 x 1/2 x 61/4 x 1/2 x 61/2 x 1/2 x 6

Hard Moldmakers StonesHard Silicon Carbide Vitrified, Green, Gray, Black

Quantity1-11 Each1-4 Doz.5-9 Doz.10 Doz. +

DiscountNet10%15%30%

Superfine StonesCalcined Alumina, Soft Bond 6" Only 900

Grit, White In Color

17612_Sticks_P21_30 7/20/05 10:02 AM Page 21

22

Stone Size 80 120 180 220 320 400 600

1/16 x 1/4 x 61/16 x 1/2 x 61/8 x 1/8 x 61/8 x 1/4 x 61/8 x 1/2 x 63/16 Sq. x 61/4 x 1/4 x 61/4 x 1/2 x 6

Grit

Stone Size 46 60 80 100 150 220

1/8 x 1/4 x 61/8 x 1/2 x 63/16 Sq. x 61/4 x 1/4 x 61/4 x 1/2 x 61/4 x 1 x 6

3/8 x 3/8 x 61/2 x 1/2 x 61/2 x 1 x 61 x 1 x 61 x 2 x 61 x 2 x 8

Grit

All sizes in allgrits available

Stone Size 100 150 220 320 400 500 600

1/16 x 1/4 x 61/16 x 1/2 x 61/8 x 1/4 x 61/8 x 1/2 x 61/8 x 1 x 6

1/4 x 1/4 x 61/4 x 1/2 x 61/4 x 1 x 6

3/8 x 3/8 x 61/2 x 1/2 x 61/2 x 1 x 61 x 1 x 6

Grit

All sizes in all grits available

Resin Bonded StonesRegular A/O, Hard Bond, Dark Brown Color

Distributor discount is calculated only after quantity discount is takenRounds are considered specials and may require long lead time.We stock many rounds in a variety of sizes and specifications,

Please contact us for availability of rounds you require.

Hard Polishing StonesPreminum Aluminum Oxide, Vit. Oil Treated, Cream

Stone Size 100 150 220 320 400 500 600 800 900 1000

1/16 x 1/4 x 61/16 x 1/2 x 61/8 x 1/4 x 61/8 x 1/2 x 61/8 x 1 x 6

1/4 x 1/4 x 61/4 x 1/2 x 61/4 x 1 x 6

3/8 x 3/8 x 61/2 x 1/2 x 61/2 x 1 x 61 x 1 x 6

Grit

All sizes in all grits available

General Polishing StonesSemi Hard, A/O, Vitrified, Wax Treat, Off White Color

Ruby StonesFast Cutting A/O, Pink Color

Quantity1-11 Each1-4 Doz.5-9 Doz.10 Doz. +

DiscountNet10%15%30%

All sizes in all gritsavailable

17612_Sticks_P21_30 7/20/05 10:02 AM Page 22

23

Stone Size Length Grit Sizes Hardness Available Shapes

1/4" To 6" 54 Thru 220 Soft, Firm, Hard Round, Triangle, Square3/8", 1/2", 5/8" To 8" 54 Thru 220 Soft, Firm, Hard Round, Triangle, Square

3/4" & 1" To 12" 54 Thru 220 Soft, Firm, Hard Round, Triangle, Square

Cross Section Length Grit Sizes Hardness Available Shapes

1/4" To 8" 54 Thru 320 F Thru K Round, Triangle, Square3/8", 1/2", 5/8" To 8" 54 Thru 320 F Thru K Round, Triangle, Square

3/4" & 1" To 12" 54 Thru 320 F Thru K Round, Triangle, Square

Bias CutThickness Width Length

1/4" 1" 2"3/8" 1-1/8" 2-1/4"1/2" 1-1/8" 2-3/4"3/4" 2" 3-1/4"

Metal Polishing & Cleaning

Rubber Bond Sticks

Rubber Bond Polishing Pieces

Cotton Fiber Reinforced Resin Sticks

Rectangular BlocksThickness Width Length

1/4" To 12" To 12"3/8" To 12" To 12"1/2" To 12" To 12"3/4" To 12" To 12"

Honing Oils

S&S Honing Oils are specially compounded for ferrous and non ferrous honing to:1. Dissipate heat from the workpiece. 3. Flush bore free of honing swarf2. Lubricate stones in contact with bore. 4. Maintain clean free cutting conditions

S&S-230 Honing OilA petroleum-based sulphurized honing oil recommended for precision honing of ferrous metals andalloys used for all steel, cast iron carbide, aluminum, bronze and ceramics. Used with all types of honingequipment.

S&S-230-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Gallon PailS&S-230-55 . . . . . . . . . . . .55 Gallon Drum (nonreturnable)

S&S-130 Honing OilA heavy duty non-chlorinated honing oil for use for ferrous and non-ferrousmetals. Excellent for external as well as internal applications. Excellent forSuperior type and Tennessee type two stone honing Systems.

S&S-130-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Gallon PailS&S-130-55 . . . . . . . . . . . .55 Gallon Drum (nonreturnable)

17612_Sticks_P21_30 7/20/05 10:02 AM Page 23

24

Convert your standard drill press into a hone in seconds with the:MD-1 Mandrel Driver

The MD-1 is the answer to all non-production honing in anyshop. Converts any drill press into a hone with the flip of awrist, no tools necessary.Available with #2, 3, or 4 Morse Taper, straight or specialshanks available.Will drive all standard two stone honing mandrels in 1/8"through 3". Included in all honing kits shown below.

DK-5001/8" to 1/2" inclusive, consisting of:1-DK-50 Mandrel Case7 Mandrels 1/8" to 1/2"7 Sets of Stones

Shipping Weight: 12 lbs.

TRK-10003/16" to 1" inclusive, consisting of:1-MD-1 Mandrel Driver No. 2, 3, or 4 Morse Taper1-MD-100 Mandrel Case13 Mandrels 3/16" to 1" inclusive13 Sets Roughing Stones13 Sets Semi-finishing Stones

Shipping Weight: 39 lbs.

TRK-15003/16" to 1-1/2" inclusive, consisting of:1-MD-1 Mandrel Driver No. 2, 3, or 4 Morse Taper1-MD-150 Mandrel Case17 Mandrels 3/16" to 1-1/2" inclusive17 Sets Roughing Stones17 Sets Semi-finishing Stones

Shipping Weight: 80 lbs.

TRK-20003/16" to 2" inclusive, consisting of:1-MD-1 Mandrel Driver No. 2, 3, or 4 Morse Taper1-MD-100 Mandrel Case1-MD-200 Mandrel Case21 Mandrels 3/16" to 2" inclusive21 Sets Roughing Stones21 Sets Semi-finishing Stones

Shipping Weight: 108 lbs.

TRK-20011-1/8" to 2" inclusive, consisting of:1-MD-201 Mandrel Case6 Mandrels 1-1/8" to 2" inclusive8 Sets Roughing Stones8 Sets Semi-finishing Stones

Shipping Weight: 35 lbs.

TRK-25003/16" to 2-1/2" inclusive, consisting of:1-MD-1 Mandrel Driver No. 2, 3, or 4 Morse Taper1-MD-150 Mandrel Case1-MD-250 Mandrel Case25 Mandrels 3/16" to 2-1/2" inclusive25 Sets Roughing Stones25 Sets Semi-finishing Stones

Shipping Weight: 120 lbs.

TRK-30003/16" to 3" inclusive, consisting of:1-MD-1 Mandrel Driver No. 2, 3, or 4 Morse Taper1-MD-100 Mandrel Case1-MD-200 Mandrel Case1-MD-300 Mandrel Case29 Mandrels 3/16" to 3" inclusive29 Sets Roughing Stones29 Sets Semi-finishing Stones

Shipping Weight: 140 lbs.

17612_Sticks_P21_30 7/20/05 10:02 AM Page 24

25

Convert your Sunnen honeinto a two stone honingmachine with the W-1000Adapter

To hone the same bore with a two stone mandrel, all you would require is:1-1-3/8" Mandrel1-Set 1-3/8" Stones

• Instant set up – without tools

• Huge abrasive hones to do the work withextreme long life of honing stones

• Only abrasives in contact with bore beinghoned, no metal contact with part

• Parts with keymaps or ports are easilyhoned without special honing stones

• No loose parts to wear out or lose, onlythe mandrel and stone set

The W-1000 converts a Sunnen machine to accept any brand of two stone mandrels rather than a singlestone which Sunnen uses. In addition, Sunnen supplies a tiny abrasive stone along with a great numberof other parts to comprise one mandrel assembly. All brands of two stone mandrel assemblies are madeup of only two parts, the mandrel and two massive stones. See comparisons below.

Example: To hone a 1-3/8" bore 10" long, you would require the following parts to do the job with aSunnen hone:

1-3G-P28-1375WC Mandrel 3-P28 Stones1-3G-P28 Tension Block 1-3G-P28 Wedge1-3G-P28 Retainer Block 3-WC-D Guide Shoes

17612_Sticks_P21_30 7/20/05 10:02 AM Page 25

26

Superior – Tennessee Two Stone HonesShop Guide

17612_Sticks_P21_30 7/20/05 10:02 AM Page 26

27

Sunnen-Superior – Tennessee Hone

17612_Sticks_P21_30 7/20/05 10:02 AM Page 27

28

UPC Code # UPC Code #730006 730006

• 1/4 x 3/8 x 4 ASD220-R100B99-1/16 02240 1/4 x 3/8 x 4 ASD220/400-R100B99-1/16One Insert 1/16 x 1 x 3/8 One End Two Inserts 1/16 x 1 x 3/8 On Each End

Size, Type and Specification Size, Type and Specification

Norton Diamond Hand Hones

Resinoid Diamond Hand Hones

For ASI-218, Sunnen & SuperiorRecommended Stone Sets

The above are the two most common diamond hand hones used. We can supply specials.

17612_Sticks_P21_30 7/20/05 10:02 AM Page 28

29

The smallest of the ASI portable kits, yet ascomplete as its’ big brother. To do a variety ofjobs in the 3/4" To 1-1/4" range. The kit containsthe hone body, AB-121 drive shaft and a set ofA1B and A2B stones.

Portable Hone KitsASI General Purpose Shop Hones

UPC Code Model

01950 ASI-B3/4" To 1-1/4"

This kit, same as the B & D kit, comes complete,ready to go to work. It includes the hone bodyand the drive shaft, with four general purposestone sets, A1CD, A2CD, A3CD and A4CD.

UPC Code Model

01951 ASI-C1" To 2"

The contents of this kit are exactly like the C kit,except the honing body which is larger. Ifrequired, an A5CD and A6CD stone set is avail-able on special order to extend the range to afull 3" capacity.

BCD-Hone KitThe BCD-Hone Kit includes one each of the ASI-B, ASI-C and ASI-D kits shown above. The rangeof this kit is 3/4" through 2-1/2", with availableoversize hones, A5CD and A6CD to expand therange to 3" if desired.

All kits and replacement stones on this page areavailable from stock for immediate delivery.

UPC Code Model

01952 ASI-D1-1/2" To 2-1/2"

UPC Code #730006

Stone Range

01911 A1B 3/4" To 1"

01912 A2B 1" To 1-1/4"

Replacement Stone Sets For ASI-B(3 per set)

UPC Code #730006

Stone Range

01913 A1CD 1" To 1-1/4"

01914 A2CD 1-1/4"" To 1-1/2"

01915 A3CD 1-1/2" To 1-3/4"

01916 A4CD 1-3/4" To 2"

Replacement Stone Sets For ASI-C(3 per set)

UPC Code #730006

Stone Range

01913 A1CD 1-1/2" To 1-3/4"

01914 A2CD 1-3/4" To 2"

01915 A3CD 2" To 2-1/4"

01916 A4CD 2-1/4" To 2-1/2"

01917 * A5CD 2-1/2" To 2-3/4"

01918 * A6CD 2-3/4" To 3"

Replacement Stone Sets For ASI-D(3 per set)

* Available on special order

17612_Sticks_P21_30 7/20/05 10:02 AM Page 29

30

Portable Honing DevicesSmall Bore Honing Devices – 1/2" Through 3-1/2"

S&S-MiniStandard Stone 1-1/8" Long

Used in small engine repair, brake and engine cylinder work & glaze breaking and deburring.• Smallest I.D. hone available in industry • Flexible shaft • For thru or blind hole work • Use in any drill motor or

drill press • Fully adjustable cutting tension • Two grit sizes available from our stock• Custom stones available in any grit size required for the job

UPC Code #730006 Size Size Capacity

02001 S&S-Mini Hone 1/2" Through 2-1/4" Bores02027 S&S-Mini-F 1-1/8" Long , Fine Grit Replacement Stone (2 per set)02028 S&S-Mini-M 1-1/8" Long , Medium Grit Replacement Stone (2 per set)

S&S-JuniorStandard Stone 1-1/8" Long

UPC Code #730006 Size Size Capacity

02000 S&S-Junior 3/4" Through 2-1/2" Bores02024 S&S-3/4-F 3/4" Long , Fine Grit Replacement Stones (3 per set)02025 S&S-3/4-M 3/4" Long , Medium Grit Replacement Stones (3 per set)02026 S&S-3/4-C 3/4" Long , Coarse Grit Replacement Stones (3 per set)02018 S&S-1-1/8-F 1-1/8" Long , Fine Grit Replacement Stones (3 per set)02019 S&S-1-1/8-M 1-1/8" Long , Medium Grit Replacement Stones (3 per set)02020 S&S-1-1/8-C 1-1/8" Long , Coarse Grit Replacement Stones (3 per set)

S&S-MiddleStandard Stone 2" Long

UPC Code #730006 Size Size Capacity

02003 S&S-Middle 1-1/4" Through 3-1/2" Bores02018 S&S-1-1/8-F 1-1/8" Long , Fine Grit Replacement Stones (3 per set)02019 S&S-1-1/8-M 1-1/8" Long , Medium Grit Replacement Stones (3 per set)02020 S&S-1-1/8-C 1-1/8" Long , Coarse Grit Replacement Stones (3 per set)02021 S&S-2-F 2" Long , Fine Grit Replacement Stones (3 per set)02022 S&S-2-M 2" Long , Medium Grit Replacement Stones (3 per set)02023 S&S-2-C 2" Long , Coarse Grit Replacement Stones (3 per set)

17612_Sticks_P21_30 7/20/05 10:02 AM Page 30

31

Portable Honing DevicesMedium And Large Bore Honing Devices 2" Through 10"

Used in all types of bore refinishing, hydraulic cylinders, engine cylinders and any I.D. pipe or tubingwhich requires a honed finish. Excellent for deburring work in all kinds of machine shop applications.Precision sizing is available with knurled thumb screw adjustment.

Both of the hones on this page are adjustable to pro-vide constant pressure on the bore wall and to com-pensate for the hone stone wear.

Model S&S-JumboCapacity 2" Through 7"

Available With Standard Stones In 3" Or 4"

UPC Code#730006 Model Size Capacity

02006 S&S-Jumbo-3 2" Through 7"01999 S&S-Jumbo-4 2" Through 7"02012 S&S-3-F 3" Long Fine Replacement Stone 3/Set02013 S&S-3-M 3" Long Medium Replacement Stone 3/Set02014 S&S-3-C 3" Long Coarse Replacement Stone 3/Set02015 S&S-4-F 4" Long Fine Replacement Stone 3/Set02016 S&S-4-M 4" Long Medium Replacement Stone 3/Set02017 S&S-4-C 4" Long Coarse Replacement Stone 3/Set

Model S&S-Maxi-JumboCapacity 6" Through 10"

Standard Stone Is 4" Long

UPC Code#730006 Model Size Capacity

02005 S&S-Maxi-Jumbo 6" Through 10"02012 S&S-3-F 3" Long Fine Replacement Stone 3/Set02013 S&S-3-M 3" Long Medium Replacement Stone 3/Set02014 S&S-3-C 3" Long Coarse Replacement Stone 3/Set02015 S&S-4-F 4" Long Fine Replacement Stone 3/Set02016 S&S-4-M 4" Long Medium Replacement Stone 3/Set02017 S&S-4-C 4" Long Coarse Replacement Stone 3/Set

17612_Sticks_P31_40 7/20/05 10:09 AM Page 31

Double StoneMaster Holder

4 Per Set– –– –

01932 ASI-56901933 ASI-57801934 ASI-58801935 ASI-598

ASI-541

32

Hand Feed Portable HoneASI-218

Ideal for occasional heavy duty portable honing. Range 3" Through 21"

ASI-Portable Hone Accessories

Replacement Stone Sets2-Stone And 2-Felt Wipers

Range Single StoneDiameter Master HolderIn Inches 4 Per Set3 - 4-3/4 01922 ASI-400

3-3/4 - 6-1/2 01923 ASI-5006 - 9 01924 ASI-6008 -12 01925 ASI-700

11 - 15 01926 ASI-80014 - 18 01927 ASI-90017 - 21 ASI-140

UPC Code#730006

UPC Code#730006

HolderSupport BoxPart Number

– –– –

01940 ASI-A6201941 ASI-A8201942 ASI-A9201943 ASI-A43

ASI-A54

UPC Code#730006

UPC Code Part Grit For Use On#730006 Number Size Material

01976 ASI-1 C80 Coarse Cast Iron01977 ASI-2 C150 Med. Cast Iron01979 ASI-3 C280 Fine Cast Iron01980 ASI-4 C400 Ex/Fn Cast Iron01978 ASI-5 C220 Med/Fn Cast Iron

• ASI-6 C600 Sup/Fn All Metals• ASI-7 A80 Coarse HD. Sleeves

UPC Code Part Grit For Use On#730006 Number Size Material

• ASI-8 A150 Med. HD. Sleeves• ASI-9 A220 Med/Fn HD. Sleeves• ASI-10 A280 Fine HD. Sleeves• ASI-11 A80 Coarse Steel• ASI-12 A150 Med. Steel• ASI-13 A220 Med/Fn Steel• ASI-14 A280 FIne Steel

UPC Code Part Grit For Use On#730006 Number Size Material

01981 ASI-1S C80 Coarse Cast Iron01982 ASI-2S C150 Med. Cast Iron01984 ASI-3S C280 Fine Cast Iron01985 ASI-4S C400 Ex/Fn Cast Iron01983 ASI-5S C220 Med/Fn Cast Iron

• ASI-6S C600 Sup/Fn All Metals• ASI-7S A80 Coarse HD. Sleeves

UPC Code Part Grit For Use On#730006 Number Size Material

• ASI-8S A150 Med. HD. Sleeves• ASI-9S A220 Med/Fn HD. Sleeves• ASI-10S A280 Fine HD. Sleeves• ASI-11S A80 Coarse Steel• ASI-12S A150 Med. Steel• ASI-13S A220 Med/Fn Steel• ASI-14S A280 FIne Steel

4-Stone Sets

17612_Sticks_P31_40 7/20/05 10:09 AM Page 32

33

Portable Honing Kits

UPC Code Model

01954 ASI-218 Kit

Contents:• Honing body with yoke and pinion drive shaft.• One set ASI-400 stone holders.• One set ASI-5 stones and felts.

Range – 3" to 5"

The ASI body and drive shaft are included in all honing kits. In the ASI-218 kit above, you get one set ofstones and a set of stone holders.

UPC Code Model

01956 “E” Kit

Contents:• Honing body with yoke and pinion drive shaft.• Two sizes of stone holder sets.• Six sets of honing stones.• Metal storage box

Range – 3" to 6-1/2"

The above kit may be expanded to a capacity of 9" by the simple addition of an extra set of stone hold-ers, ASI-600 and a holder support box ASI-A62.It is also possible to increase capacity to 12" in the same manner, both at a nominal cost.

UPC Code Model

01957 “F” Kit

Contents:• Honing body with yoke and pinion drive shaft.• Five sizes of stone holder sets.• Three sizes of holder support boxes.• Six sets of honing stones.• Metal storage box

Range – 3" to 15"

This kit may be expanded to 21" if required. Simply add the extra oversize stone holder sets and theappropriate support boxes to whatever size is desired.Above 15" with any individual tool or kit is recommended only with two stone master holders.All accessory items to expand capacity of any device are found on the previous page.

17612_Sticks_P31_40 7/20/05 10:09 AM Page 33

34

UPC Model Grit DiamondCode # Size Area

07216 W6FS FINE 6" x 2"07217 W6CS COARSE 6" x 2"07220 W6FP FINE 6" x 2"07221 W6CPS COARSE 6" x 2"07224 W8F FINE 8" x 2-5/8"07225 W8C COARSE 8" x 2-5/8"

UPC Model Grit DiamondCode # Size Area

07159 FSKF FINE SERRATED07160 FSKC COARSE SERRATED07161 FFF FINE 4" LONG TAPER07162 FFC COARSE 4" LONG TAPER07166 FRF* FINE 1/4 ROUND ROD07167 FRC* COARSE 1/4 ROUND ROD07168 FHRF FINE 1/4 HALF RD.

UPC Model Grit DiamondCode # Size Area

07151 FWF FINE 4-1/3" x 7/8"07152 FWC COARSE 4-1/3" x 7/8"07157 FMF FINE 4-1/3" x 7/8"07158 FMC COARSE 4-1/3" x 7/8"

UPC Model Grit DiamondCode # Size Area

07180 F70E X-FINE 2-11/16 x 15/1607181 F70F FINE 2-11/16 x 15/1607182 F70C COARSE 2-11/16 x 15/1607183 F70X X-COARSE 2-11/16 x 15/16

UPC Model Grit DiamondCode # Size Area

07103 W3C* COARSE 3-1/3" x 7/8"07106 W4F FINE 4-1/3" x 7/8"07107 W4C COARSE 4-1/3" x 7/8"

UPC Model GritCode # Size

07250 AKEF X-FINE & FINE07251 AKFC FINE & COARSE

Aligner™ Guided Sharpening Kits

Diamond Whetstones™ - Bench Models

Pocket Models

Diafold™ Diamond Whetstone™

Diamond Mini-Sharp™ Sharpener

Diafold™ Sharpeners & Diafold™ Folding Files

* Limited Quantities on items W3C, FRF and FRC

17612_Sticks_P31_40 7/20/05 10:10 AM Page 34

35

UPC Code # Tool Type & Number Shank Shank Length730006 Multi-Point Nibs Size Shape Diameter Under Head

02250 1A 7/16" 3/4"

02252 1A 7/16" 7/8"

02253 2A 7/16" 7/8"

02254 2A 7/16" 3/4"

02256 1R 7/16" 1-1/2"

02258 2R 7/16" 1-1/2"

General Purpose Diamond Dressing Tools

S&S-60

S&S-61

S&S-62

S&S-63

S&S-64

S&S-65

Diamond Section

1-1/2" hollow shaft holder, for offhand truing and dressingusing any tool with shank length from 3/4" to 9". The collettaccepts only 7/16" diameter shank.

UPC Code # Tool Type & Number Carat Shank Shank 730006 Multi-Point Nibs Weight Diameter Length

02260 S&S-2-3 1/4 (.25) 3/8" 2"

02261 S&S-2 1/4 (.25) 7/16" 2"

02262 S&S-3-3 1/3 (.33) 3/8" 2"

02263 S&S-3 1/3 (.33) 7/16" 2"

02264 S&S-5-3 1/2 (.50) 3/8" 2"

02265 S&S-5 1/2 (.50) 7/16" 2"

02267 S&S-7 3/4 (.75) 7/16" 2"

02269 S&S-10 1 (1.00) 7/16" 2"

Phono Point Tools Included Angle

02270 S&S-PP-60 60˚ 1/8" 1"

02271 S&S-PP-75 75˚ 1/8" 1"

02272 S&S-PP-90 90˚ 1/8" 1"

02273 S&S-RD For Dressing 3/8" 2"

Radii of .015"

Radius Tool Through .025"

02280 S&S-HD Diamond Tool Holder

Single Point Tools

17612_Sticks_P31_40 7/20/05 10:10 AM Page 35

Part Number

Brake Cylinders, Hydraulics & ValveGuides

8" OAL

36

Flex-Hone® Tool

Part Number 120SC 180SC 240SC 320SC

BC 5 mm (.197) • 02045 • 02046BC 5.5 mm (.217) • 02043 • •BC 6.4 mm (.250) • 02047 • •BC 7 mm (.276) • 02048 • •BC 8 mm (.315) • 02051 02052 •BC 9 mm (.354) • 02049 • •BC 9.5 mm (.375) • 02050 • •BC 10 mm (.394) • 02053 • •BC 11 mm (.433) • 02044 • •BC 12 mm (.472) • 02055 • •BC 1/2" (12.7 mm) 02057 20256 • 02058BC 14 mm (.552) • 02054 • •BC 5/8" (16 mm) • 02062 • •BC 18 mm (.709) • 02059 • •BC 3/4" (19 mm) • 02064 • 02068BC 20 mm (.787) • 02060 • •BC 7/8" (22 mm) • 02066 02067 •BC 1" (25.4 mm) 02072 02070 • •BC 1-1/8" (29 mm) • 02077 02079 02078BC 1-1/4" (31.8 mm) • 02080 02081 •BC 1-3/8" (35 mm) • 02082 • •BC 1-1/2" (38 mm) • 02084 • •BC 1-5/8" (41 mm) • 02088 • •BC 1-3/4" (45 mm) • 02086 • •BC 2" (51 mm) • 02090 • •BC 2-1/4" (57 mm) • 02073 • •BC 2-1/2" (64 mm) • 02098 • •BC 2-3/4" (70 mm) • 02100 • •BC 3" (76 mm) • 02102 • •

Part Number For Bore Sizes 120SC 180SC 240SC

GBD 3" (76 mm) 3" to 2-3/4" • • •GBD 3-1/4" (83 mm) 3-1/4" to 3" • • •GBD 3-1/2" (89 mm) 3-1/2" to 3" • • •GBD 3-3/4" (95 mm) 3-3/4" to 3-1/4" • • •GBD 4" (101 mm) 4" to 3-1/2" • • •GBD 4-1/4" (108 mm) 4-1/4" to 3-3/4" • • •GBD 4-1/2" (114 mm) 4-1/2" to 4" • • •GBD 5" (127 mm) 5" to 4-1/2" • • •GBD 5-1/2" (140 mm) 5-1/2" to 5" • • •GBD 6" (152 mm) 6" to 5-1/2" • • •GBD 6-1/2" (165 mm) 6-1/2" to 6 • • •GBD 7" (178 mm) 7" to 6-1/2" • • •GBD 7-1/2" (190 mm) 7-1/2" to 7" • • •GBD 8" (203 mm) 8" to 7-1/2" • • •

Part Number 120SC 180SC 240SC 320SC

GB 3-1/4" (83 mm) • 02103 • •GB 3-1/2" (89 mm) • 02099 • •GB 3-3/4" (95 mm) • • • •GB 4-1/8" (105 mm) • • • •GB 4-5/8" (118 mm) • • • •

3" Core (1/2" Hex-Shaft) 120SC 180SC 240SC

GBDH 8" (203 mm) • • •GBD 8-1/2" (216 mm) • • •GBD 9" (228 mm) • • •GBD 9-1/2" (241 mm) • • •GBD 10" (254 mm) • • •

4" Core (1/2" Hex-Shaft) 120SC 180SC 240SC

GBD 10-1/2" (267 mm) • • •GBD 11" (280 mm) • • •GBD 11-1/2" (292 mm) • • •GBD 12" (305 mm) • • •

Part Number 120SC 180SC 240SC

DBC 1-1/2" (38 mm) • • •DBC 1-3/4" (48 mm) • • •DBC 2-1/8" (54 mm) • 02094 •DBC 2-1/2" (64 mm) • 02096 •DBC 2-3/4" (70 mm) • • •DBC 3-1/8" (79 mm) • • •

5" Core (5/8" Hex-Shaft) 120SC 180SC 240SC

GBD 12-1/2" (318 mm) • • •GBD 13" (330 mm) • • •GBD 13-1/2" (344 mm) • • •GBD 14" (355 mm) • • •

6" Core (5/8" Hex-Shaft) 120SC 180SC 240SC

GBD 15" (381 mm) • • •GBD 16" (406 mm) • • •

8" Core (5/8" Hex-Shaft) 120SC 180SC 240SC

GBD 17" (432 mm) • • •GBD 18" (457 mm) • • •

Disc Brakes5" OAL

Engine Block Cylinders13-1/2" OAL

Heavy Duty Hex Shaft34" OAL

• = No UPC Code Assigned

Block Cylinders or LinersHeavy-duty Flex Hones3" thru 4-1/2" dia. are 13-1/2" OALBal. 17-1/2" OAL

17612_Sticks_P31_40 7/20/05 10:10 AM Page 36

37

Flex-Hone® ToolExtra Heavy DutyShafts 3/4" - 1-1/4" Flex-Hone® Tool Accessories

No. ofDrum Sections Shaft

Part Number Dia. Section on Drum Dia.

GBDX 19" (483mm) 11-1/2" A 22 3/4"GBDX 20" (508mm) 11-1/2" B 22 3/4"GBDX 21" (533mm) 11-1/2" C 22 3/4"GBDX 22" (559mm) 11-1/2" D 22 3/4"GBDX 23" (584mm) 15-1/2" A 29 3/4"GBDX 24" (610mm) 15-1/2" B 29 3/4"GBDX 25" (635mm) 15-1/2" C 29 3/4"GBDX 26" (660mm) 15-1/2" D 29 3/4"GBDX 27" (686mm) 19-1/2" A 36 1"GBDX 28" (711mm) 19-1/2" B 36 1"GBDX 29" (737mm) 19-1/2" C 36 1"GBDX 30" (762mm) 19-1/2" D 36 1"GBDX 31" (787mm) 19-1/2" E 36 1"GBDX 32" (813mm) 24-1/2" A 44 1-1/4"GBDX 33" (838mm) 24-1/2" B 44 1-1/4"GBDX 34" (864mm) 24-1/2" C 44 1-1/4"GBDX 35" (889mm) 24-1/2" D 44 1-1/4"GBDX 36" (914mm) 24-1/2" E 44 1-1/4"

Pipe Nipple AdaptersPipe Size Flex-Hone Sizes

832A 8-32 Adapters 7mm-1/2"18NPT 1/8" NPT 5/8"-3"14NPT 1/4" NPT 3"-5-1/2"38NPT 3/8" NPT 6"-8"12NPT 1/2" NPT 6"-12"

18 x 18 1/8" NPT x 18" w/coupling18 x 36 1/8" NPT x 36" w/coupling14 x 18 1/4" NPT x 18" w/coupling14 x 36 1/4" NPT x 36" w/coupling

GBDX-A Section - 4-1/8" (105mm) Overall TrimGBDX-B Section - 4-5/8" (118mm) Overall TrimGBDX-C Section - 5-1/4" (133mm) Overall TrimGBDX-D Section - 5-3/4" (146mm) Overall TrimGBDX-E Section - 6-3/8" (162mm) Overall Trim

Grit Types 20 40 60 80 120 180 240 320SC = Silicon Carbide X X X X Standard Grits

AO = Aluminum Oxide X X X X X X X XBC = Boron Carbide X X X X X X X X

WC = Tungsten Carbide X X X X X X X X(100% or 50/50)

Z = Alumina Zirconia X X X X X X(25 Z & 75 A)

Finer Grits May Be Available On Request

FS 14" OAL 6˚ Max Bend

Extensions for use with pipe nipple adapters

Flex-Shaftfor in chassis-engine on 3" to 45/8" FH diameters

GBDX Replacement Sections Availablefor Above GBDX Flex-Hone® Tools

Stem Marking – Type of AbrasiveSC –Silicon Carbide . . . . . . . . . . . . . . . . . . . . . . . . . . . no color

(Recommended for ferrous metals)

AO – Aluminum Oxide . . . . . . . . . . . . . . . . . . . . . . . . . black

BC – Boron Carbide . . . . . . . . . . . . . . . . . . . . . . . . . . . gold

WC – Tungsten Carbide . . . . . . . . . . . . . . . . . . . . . . . . tanLevigated Alumina (super fine) . . . . . . . . . . . . . green

Z Grain – Zirconia Alumina . . . . . . . . . . . . . . . . . . . . . red

End Marking – Grit Size20 (brown) 120 (silver or no color) 320 (white)

40 (purple) 180 (cardinal red) 400 (yellow)

60 (grey) 240 (navy blue) 600 (pink)

80 (orange) 800 (light blue)

Instructions For Use

The Flex-Hone Tool should be rotating upon entry and removal fromcylinder. RPM from 1200 to 60 depending on diameter. Stroke from 30to 200 per minute depending upon RPM. Average 350-500 RPM at 60-120 strokes. Final stroking may be accelerated to develop 45˚ crosshatch. OEM high production needs experimentation with different min-eral or water-soluble honing oils for optimum results. For convenienceuse a 10-30 wt. motor oil or our FlexHone Oil. Wash cylinder prefer-ably with water, brush and detergent, then dry and oil. Experimenthoning time from 10 to 45 seconds just sufficient to develop plateauedfinish free from cut, torn and folded metal. Do not overhone.

Ask for Honing Booklets availble at no charge.

Abrasive Options

17612_Sticks_P31_40 7/20/05 10:10 AM Page 37

38

S&S Finishing Stick

The most innovative tool from the abrasive industry in forty years.

All tools and abrasive belts are color coded for instant identification of tool and abrasive beltgrit size. Tool is available in three sizes.

UPC Code # Size, Color &73006 Grit Size

02500 1/4" BROWN 40 Grit02501 1/4" GRAY 80 Grit02502 1/4" RED 120 Grit02503 1/4" BLUE 240 Grit02504 1/4" GREEN 320 Grit02505 1/4" YELLOW 400 Grit02506 1/4" BLACK 600 Grit

UPC Code # Size, Color &73006 Grit Size

02600 1/2" BROWN 40 Grit02601 1/2" GRAY 80 Grit02602 1/2" RED 120 Grit02603 1/2" BLUE 240 Grit02604 1/2" GREEN 320 Grit02605 1/2" YELLOW 400 Grit02606 1/2" BLACK 600 Grit

UPC Code # Size, Color &73006 Grit Size

02700 3/4" BROWN 40 Grit02701 3/4" GRAY 80 Grit02702 3/4" RED 120 Grit02703 3/4" BLUE 240 Grit02704 3/4" GREEN 320 Grit02705 3/4" YELLOW 400 Grit02706 3/4" BLACK 600 Grit

UPC Code # Belt &73006 Grit Size

02510 1/4" 40 Grit02511 1/4" 80 Grit02512 1/4" 120 Grit02513 1/4" 240 Grit02514 1/4" 320 Grit02515 1/4" 400 Grit02516 1/4" 600 Grit

UPC Code # Belt &73006 Grit Size

02610 1/2" 40 Grit02611 1/2" 80 Grit02612 1/2" 120 Grit02613 1/2" 240 Grit02614 1/2" 320 Grit02615 1/2" 400 Grit02616 1/2" 600 Grit

UPC Code # Belt &73006 Grit Size

02710 3/4" 40 Grit02711 3/4" 80 Grit02712 3/4" 120 Grit02713 3/4" 240 Grit02714 3/4" 320 Grit02715 3/4" 400 Grit02716 3/4" 600 Grit

1/4" x 6" Tools 1/2" x 8" Tools

Replacement Belts

3/4" x 10" Tools

17612_Sticks_P31_40 7/20/05 10:10 AM Page 38

Norton Pacesetter Mounted Points

A ShapesThe standard shank size is 1/8", 1/4" x 1-1/2" and 3/8 x 2". All coarse (CRS) grits are hard grade.

All medium (M) and medium/tine (M/F) grits are medium grade.

UPC Code # Shape Size Spec Spindle Speed*730006 RPM

04000 A1 3/4 x 2-1/2 38A CRS 1/4 19,80004001 A1 3/4 x 2-1/2 38A M 1/4 19,80004005 A2 1 x 1-1/4 38A M 1/4 38,20004006 A3 1 x 2-3/4 38A CRS 1/4 16,10004007 A3 1 x 2-3/4 38A M 1/4 16,10004010 A4 1-1/4 x 1-1/4 38A CRS 1/4 30,56004011 A4 1-1/4 x 1-1/4 38A M 1/4 30,56004015 A5 3/4 x 1-1/8 38A CRS 1/4 45,00004016 A5 3/4 x 1-1/8 38A M 1/4 45,00004020 A6 3/4 x 1-1/8 38A M 1/4 39,00004025 A11 7/8 x 2 38A CRS 1/4 19,86004026 A11 7/8 x 2 38A M 1/4 19,86004030 A12 11/16 x 1-1/4 38A CRS 1/4 48,00004031 A12 11/16 x 1-1/4 38A M 1/4 48,00004035 A13 1-1/8 x 1-1/8 38A M 1/4 33,95004037 A14 11/16 x 7/8 38A M 1/4 55,56004040 A15 1/4 x 1-1/16 38A M 1/4 72,75004043 A21 1 x 1 38A M 1/4 34,50004045 A22 3/4 x 5/8 38A M 1/4 50,93004047 A23 3/4 x 1 38A M 1/4 39,37004050 A24 1/4 x 3/4 38A M 1/4 76,50004053 A25 1 38A M 1/4 35,62004055 A26 5/8 38A M 1/4 61,12004057 A31 1-3/8 x 1 38A CRS 1/4 27,78004060 A31 1-3/8 x 1 38A M 1/4 27,78004063 A32 1 x 5/8 38A M 1/4 38,20004065 A33 1 x 1/2 38A M 1/4 38,20004067 A34 1-1/2 x 3/8 38A M 1/4 25,47004070 A35 1 x 3/8 38A M 1/4 38,20007073 A36 1-5/8 x 3/8 38A M 1/4 23,52004075 A37 1-1/4 x 1/4 38A M 1/4 30,56004077 A38 1 x 1 38A M 1/4 34,50004080 A39 3/4 x 3/4 38A M 1/4 47,25004083 A40 3/4 38A M 1/4 47,250

*Maximum Operating Speed based on 1/2" overhang.

A1 A2 A3

A4 A5 A6

A1 A12 A13

A14 A15 A21

A22 A23 A24

A25 A26 A31

A32 A33 A34

A35 A36 A37

A38 A39 A40

39

17612_Sticks_P31_40 7/20/05 10:10 AM Page 39

40

Norton Pacesetter Mounted Points

B ShapesThe standard shank size is 1/8", 1/4" x 1-1/2" and 3/8 x 2". All coarse (CRS) grits are hard grade.

All medium (M) and medium/fine (M/F) grits are medium grade.

UPC Code # Shape Size Spec Spindle Speed*730006 RPM

04100 B41 5/8 x 5/8 38A M 1/8 33,75004101 B41 5/8 x 5/8 38A M 1/4 61,12004105 B42 1/2 x 3/4 38A M 1/8 33,75004106 B42 1/2 x 3/4 38A M 1/4 61,12004110 B43 1/4 x 5/16 38A M 1/8 81,37004113 B44 7/32 x 3/8 38A M 1/8 68,40004115 B45 3/16 x 5/16 38A M 1/8 104,25004117 B46 1/8 x 5/16 38A M 1/8 105,00004120 B47 1/8 x 5/32 38A M 1/8 105,00004125 B51 7/16 x 3/4 38A M 1/8 45,37004128 B52 3/8 x 3/4 38A M 1/8 45,37004127 B52 3/8 x 3/4 38A M 1/4 81,00004129 B52 3/8 x 3/4 38A M/F 1/8 45,37004140 B53 5/16 x 5/8 38A M 1/8 60,00004150 B54 1/4 x 1/2 38A M 1/8 60,00004155 B55 1/8 x 1/4 38A M 1/8 105,00004157 B61 3/4 x 5/16 38A M 1/8 38,25004158 B61 3/4 x 5/16 38A M 1/4 50,93004160 B62 1/2 x 3/8 38A M 1/8 41,02004162 B63 1/4 x 3/16 38A M 1/8 92,40004164 B64 1/4 x 1/16 38A M 1/8 105,00004166 B65 1/8 x 1/8 38A M 1/8 105,00004168 B70 3/4 x 1/8 38A M 1/8 50,93004170 B71 5/8 x 3/32 38A M 1/8 61,12004172 B72 1/2 x 1/8 38A M 1/8 73,50004174 B73 1/2 x 3/32 38A M 1/8 73,50004176 B74 7/32 x 3/32 38A M 1/8 105,00004178 B81 3/4 x 3/16 38A M 1/8 50,93004180 B82 1/2 x 1/4 38A M 1/8 76,39004182 B83 3/8 x 3/16 38A M 1/8 87,60004184 B84 5/16 x 3/16 38A M 1/8 105,00004186 B90 1/2 x 1/2 38A M 1/8 34,50004188 B91 1/2 x 5/8 38A M 1/8 34,50004189 B91 1/2 x 5/8 38A M 1/4 61,50004192 B92 1/4 x 1/4 38A M 1/8 81,37004194 B93 3/16 x 3/16 38A M 1/8 105,00004196 B94 1/64 x 3/32 38A M 1/8 105,000

*Maximum Operating Speed based on 1/2" overhang.

B41 B42 B43

B44 B45 B46

B47 B51 B52

B53 B54 B55

B61 B62 B63

B64 B65 B70

B71 B72 B73

B74 B81 B82

B83 B84 B90

B91 B92 B93

B94

17612_Sticks_P31_40 7/20/05 10:10 AM Page 40

B95 B96 B97

B98 B101 B102

B103 B104 B105

B106 B111 B112

B113 B114 B115

B121 B122 B123

B124 B131 B132

B133 B134 B135

B136

Norton Pacesetter Mounted Points

B Shapes (continued)The standard shank size is 1/8", 1/4" x 1-1/2". All coarse (CRS) grits are hard grade.

All medium (M) and medium/fine (M/F) grits are medium grade.

UPC Code # Shape Size Spec Spindle Speed*730006 RPM

04198 B95 1/8 x 3/16 38A M 1/8 105,000

04201 B96 1/8 x 1/4 38A M 1/8 105,000

04200 B96 1/8 x 1/4 38A M/F 1/8 105,000

04205 B97 1/8 x 3/8 38A M 1/8 105,000

04207 B98 3/32 x 1/4 38A M 1/8 105,000

04210 B101 5/8 x 11/16 38A M 1/8 33,750

04211 B101 5/8 x 11/16 38A M 1/4 61,120

04215 B102 5/8 x 1/2 38A M 1/8 45,370

04217 B103 5/8 x 3/16 38A M 1/8 61,120

04220 B104 5/16 x 3/8 38A M 1/8 68,400

04222 B105 1/4 x 1/4 38A M 1/8 104,250

04224 B106 1/8 x 7/64 38A M 1/8 105,000

04226 B111 7/16 x 11/16 38A M 1/8 33,750

04227 B111 7/16 x 11/16 38A M 1/4 66,000

04230 B112 3/8 x 1/2 38A M 1/8 45,370

04232 B113 1/4 x 1/4 38A M 1/8 81,370

04234 B114 7/32 x 3/8 38A M 1/8 68,400

04236 B115 3/32 x 1/8 38A M 1/8 105,000

04240 B121 1/2 38A M 1/8 45,370

04241 B121 1/2 38A M 1/4 76,390

04242 B121 1/2 38A M/F 1/8 45,370

04245 B122 3/8 38A M 1/8 61,650

04246 B122 3/8 38A M/F 1/8 61,650

04250 B123 3/16 38A M 1/8 104,250

04255 B124 1/8 38A M 1/8 105,000

04256 B124 1/8 38A M/F 1/8 105,000

04258 B131 1/2 x 1/2 38A M 1/8 34,500

04259 B131 1/2 x 1/2 38A M 1/4 61,500

04260 B131 1/2 x 1/2 38A M/F 1/8 34,500

04263 B132 3/8 x 1/2 38A M 1/8 45,370

04265 B133 3/8 x 3/8 38A M 1/8 54,000

04267 B134 5/16 x 3/8 38A M 1/8 61,650

04269 B135 1/4 x 1/2 38A M 1/8 60,000

04275 B136 1/4 x 5/16 38A M 1/8 77,250

*Maximum Operating Speed based on 1/2" overhang.

41

17612_Sticks_P41_44 7/20/05 2:28 PM Page 41

42

Norton Pacesetter Mounted Points

W ShapesThe standard shank size is 1/8", 1/4" x 1-1/2" and 3/8 x 2". All coarse (CRS) grits are hard grade.

All medium (M) and medium/fine (M/F) grits are medium grade.

UPC Code # Shape Size Spec Spindle Speed730006 RPM

04300 W141 3/32 x 5/32 38A M 1/8 105,00004304 W142 3/32 x 1/4 38A M 1/8 105,00004303 W142 3/32 x 1/4 38A M/F 1/8 105,00004306 W143 1/8 x 1/8 38A M 1/8 105,00004310 W144 1/8 x 1/4 38A M 1/8 105,00004313 W145 1/8 x 3/8 38A M 1/8 105,00004314 W145 1/8 x 3/8 38A M/F 1/8 105,00004317 W146 1/8 x 1/2 38A M 1/8 105,00004318 W146 1/8 x 1/2 38A M/F 1/8 105,00004320 W149 5/32 x 1/4 38A M 1/8 105,00004322 W151 3/16 x 1/8 38A M 1/8 105,00004325 W152 3/16 x 1/4 38A M 1/8 105,00004327 W153 3/16 x 3/8 38A M 1/8 80,85004330 W154 3/16 x 1/2 38A M 1/8 70,50004332 W157 1/4 x 1/16 38A M 1/8 123,00004335 W158 1/4 x 1/8 38A M 1/8 105,00004337 W159 1/4 x 3/16 38A M 1/8 92,40004340 W160 1/4 x 1/4 38A M 1/8 81,37004343 W161 1/4 x 5/16 38A M 1/8 77,25004345 W162 1/4 x 3/8 38A M 1/8 68,40004347 W163 1/4 x 1/2 38A M 1/8 60,00004350 W164 1/4 x 3/4 38A M 1/8 45,90004352 W165 5/16 x 1/16 38A M 1/8 107,40004355 W166 5/16 x 1/8 38A M 1/8 96,97004357 W167 5/16 x 1/4 38A M 1/8 75,00004360 W168 5/16 x 5/16 38A M 1/8 68,40004363 W169 5/16 x 3/8 38A M 1/8 61,65004365 W170 5/16 x 1/2 38A M 1/8 52,50004367 W171 5/16 x 3/4 38A M 1/8 37,12004370 W172 3/8 x 1/16 38A M 1/8 99,37004373 W173 3/8 x 1/8 38A M 1/8 87,60004375 W174 3/8 x 1/4 38A M 1/8 69,00004377 W175 3/8 x 3/8 38A M 1/8 54,00004380 W176 3/8 x 1/2 38A M 1/8 45,37004383 W177 3/8 x 3/4 38A M 1/8 33,75004385 W178 3/8 x 1 38A M 1/8 26,25004387 W179 3/8 x 1-1/4 38A M 1/8 18,75004390 W181 1/2 x 1/16 38A M 1/8 76,39004393 W182 1/2 x 1/8 38A M 1/8 73,50004395 W183 1/2 x 1/4 38A M 1/8 51,75004397 W184 1/2 x 3/8 38A M 1/8 41,02004400 W185 1/2 x 1/2 38A M 1/8 34,50004401 W185 1/2 x 1/2 38A M 1/4 61,50004402 W185 1/2 x 1/2 38A M/F 1/8 34,50004406 W186 1/2 x 3/4 38A M 1/8 26,25004407 W186 1/2 x 3/4 38A M 1/4 51,00004410 W187 1/2 x 1 38A M 1/8 20,62004412 W188 1/2 x 1-1/2 38A M 1/4 30,37004415 W189 1/2 x 2 38A M 1/4 24,00004417 W190 5/8 x 1/16 38A M 1/8 61,12004420 W191 5/8 x 1/8 38A M 1/8 58,87004423 W192 5/8 x 1/4 38A M 1/8 43,12004425 W193 5/8 x 3/8 38A M 1/8 32,25004427 W194 5/8 x 1/2 38A M 1/8 29,40004428 W194 5/8 x 1/2 38A M 1/4 56,40004430 W195 5/8 x 3/4 38A M 1/8 22,12004433 W196 5/8 x 1 38A M 1/4 35,250

*Maximum Operating Speed based on 1/2" overhang.

D

T

D

T

D

T

D

T

17612_Sticks_P41_44 7/20/05 2:28 PM Page 42

43

Norton Pacesetter Mounted Points

W Shapes (continued)The standard shank size is 1/8", 1/4" x 1-1/2" and 3/8 x 2". All coarse (CRS) grits are hard grade.

All medium (M) and medium/fine (M/F) grits are medium grade.

UPC Code # Shape Size Spec Spindle Speed730006 RPM

04435 W197 5/8 x 2 38A M 1/4 21,00004437 W198 5/8 x 2-1/2 38A M 1/4 16,50004440 W199 3/4 x 1/16 38A M 1/8 50,93004443 W200 3/4 x 1/8 38A M 1/8 50,93004444 W200 3/4 x 1/8 38A M/F 1/8 50,93004447 W201 3/4 x 1/4 38A M 1/8 38,25004450 W202 3/4 x 3/8 38A M 1/8 30,60004453 W203 3/4 x 1/2 38A M 1/8 25,50004454 W203 3/4 x 1/2 38A M 1/4 50,93004457 W204 3/4 x 3/4 38A M 1/4 18,90004460 W205 3/4 x 1 38A M 1/4 34,50004463 W206 3/4 x 1-1/4 38A M 1/4 28,72004465 W207 3/4 x 1-1/2 38A M 1/4 24,00004467 W208 3/4 x 2 38A M 1/4 18,75004469 W209 3/4 x 2-1/2 38A M 1/4 15,00004472 W210 7/8 x 1/16 38A M 1/8 43,65004475 W211 7/8 x 1/8 38A M 1/8 43,65004477 W212 7/8 x 1/4 38A M 1/8 33,75004480 W213 7/8 x 3/8 38A M 1/8 27,00004483 W214 15/16 x 1/4 38A M 1/8 32,60004485 W215 1 x 1/8 38A M 1/8 38,20004491 W216 1 x 1/4 38A M 1/8 30,52004492 W216 1 x 1/4 38A M 1/4 38,20004495 W217 1 x 3/8 38A M 1/4 38,20004498 W218 1 x 1/2 38A M 1/4 38,20004500 W219 1 x 3/4 38A M 1/4 35,10004502 W220 1 x 1 38A M 1/4 25,50004505 W221 1 x 1-1/2 38A M 1/4 19,12004508 W222 1 x 2 38A CRS 1/4 15,90004509 W222 1 x 2 38A M 1/4 15,90004507 W222 1 x 2 37C CRS 1/4 15,90004512 W223 1 x 2-1/2 38A M 1/4 12,37004515 W224 1 x 3 38A M 1/4 10,60504517 W225 1-1/4 x 1/4 38A M 1/4 30,56004520 W226 1-1/4 x 3/8 38A M 1/4 30,56004523 W227 1-1/4 x 1/2 38A M 1/4 30,56004525 W228 1-1/4 x 3/4 38A M 1/4 30,52004527 W229 1-1/4 x 1 38A M 1/4 24,00004530 W230 1-1/4 x 1-1/4 38A M 1/4 20,40004533 W231 1-1/4 x 1-1/2 38A M 1/4 17,62004535 W232 1-1/4 x 2 38A M 1/4 14,25004537 W233 1-1/4 x 2-1/2 38A M 1/4 10,88004540 W234 1-1/4 x 3 38A M 3/8 24,38004543 W235 1-1/2 x 1/4 38A M 1/4 25,47004545 W236 1-1/2 x 1/2 38A M 1/4 25,47004547 W237 1-1/2 x 1 38A M 1/4 22,50004550 W238 1-1/2 x 1-1/2 38A M 1/4 15,60004553 W239 1-1/2 x 2 38A M 1/4 12,75004555 W240 1-1/2 x 2-1/2 38A M 3/8 21,00004557 W241 1-1/2 x 3 38A M 3/8 18,00004560 W242 2 x 1 38A M 1/4 19,10004563 W243 2 x 1-1/2 38A M 3/8 19,10004565 W244 2 x 2 38A M 3/8 19,10004567 W245 2 x 2-1/2 38A M 3/8 19,10004570 W246 2 x 3 38A M 3/8 16,500

*Maximum Operating Speed based on 1/2" overhang.

D

T

D

T

D

T

D

T

17612_Sticks_P41_44 7/20/05 2:28 PM Page 43

44

Effective August 1, 2005

Terms and Conditions

Minimum Order: All orders are subject to a minimum charge of $20.00. Anyorder entered having a net invoice value of less than$20.00 will be invoiced at $20.00.

Transportation: Prepaid and assumed on orders with a net value of $1,500per shipment. All others shipped collect or prepaid andadded to the invoice.

Weights: All catalog weights are approximate and are for guidanceonly.

Returned Goods: Goods may not be returned without approval. Any return mustbe accompanied by a Returned Goods Authorization number(RGA #) furnished by sales dept.

Damaged Goods: Damage must be reported immediately to carrier and claimfiled at the distributor end. Hidden damage must be reported tous within five working days of receipt of goods.

Prices Are Subject To Change Without Notice

Sticks & Stones Unlimited, Inc.Distributed By:

17612_Sticks_P41_44 7/20/05 2:28 PM Page 44