Step Gauges Accessories Evaluation Software Training · Step gauges - Accessories – Evaluation...
Transcript of Step Gauges Accessories Evaluation Software Training · Step gauges - Accessories – Evaluation...
• Step Gauges
• Accessories
• Evaluation Software
• Training
Step gauges for monitoring of coordinate measuring machines
Product range Practice
Characteristics
Step gauges for monitoring of coordinate measuring machines
• Available in the following lengths:300, 500, 700, 1060, 1100, 1540 und1980 mm
• Other lengths on request
• Ceramic gauge blocks Ø 8,5 x 20 mm• Cross-section support body: 55 x 55 • Distance of the test cylinder: 20 mm• Ensure long-term stability• Temperature scale at the step gauge• Marking of the Bessel points• Galvanized surfaces• Supplied in Aluminium Case• Supplied on request with DKD
calibration or proprietary calibration • Special lengths• Compatible with the current
standards (ISO 10360) and VDI 2617• Device-independent evaluation
software available• Extensive accessory for practical use
Your CMM should be subject to constant monitoring of the accuracy.
Best possibility for this test are the step gauge.
This test equipment gives quickly and comprehensible statements about the accuracy of the machine to be tested.
In order to adjust the different positions quick and reproducible, the step gauge can be mounted on the rotating swivel fixture.
With the integrated clamping device, the step gauge is held securely in any position.
Step gauges - Accessories – Evaluation software - Training - Calibration
Accessories for stepgage
Step gauges for monitoring of coordinate measuring machines
• The SE-holder will be delivered with the pipe extension which matches to your step gauge so you are also be able to measure in vertical direction.
• Delivery is by default in a high-quality aluminum case
• The fixture matches to the gauge length
• Turning and swiveling possible
• Optional, stable base plate (if the device can not be mounted directly on the machine table)
• Fixed locking positions horizontally and vertically in 35 ° | 0 ° | 90 °
• In addition, also continuously adjustable
• Direct mounting on machine table by means of central bore in adapter plate
• Additional standpipes and adapter can be ordered separately
• Fixture for SE 300mm (swiveling only)
Step gauges - Accessories – Evaluation software - Training - Calibration
Independent of CMM-TypeEvaluation Software ITI-Check
Training
For an efficient use of the evaluationsoftware we offer a training courseof 1 day.
Step gauges for monitoring of coordinate measuring machines
With the universal evaluation software ITI check you are able to check the volumetric length measuring error MPEE on your CMM regarding ISO 10360.
The analysis can be carried out according to ISO10360 or VDI/VDE2617.
Supported are the measuringsparallel to the axis and also volumetric.
If desired, you can also control the volumetric probing error MPEP. A precision sphere has to be measured with 25 equally distributed probings. MPEP is the range of all radii (sphere form).
ITI-check only needs a special programmable adapter for reading text files and is therefore independent from the equipment and software configurations.
For Zeiss Calypso users a PCM based measuring program is included.
Step gauges - Accessories – Evaluation software - Training - Calibration
DKD - Calibration Specifications
Step gauges for monitoring of coordinate measuring machines
Upon request we provide the step gauge with DKD calibration.
There are two different calibration steps.
Niveau 1 :
U=0,1 µm + 0,5 x 10-6 x L (L=Length)
Niveau 2 :
U=0,2 µm + 0,5 x 10-6 x L (L=Length)
The required calibration niveau must be specified in the order.
Measuring range (total length) in mm
Standard lengths:• 300 (320)• 500 (520)• 700 (720)• 1060 (1080)• 1100 (1120)• 1540 (1560)
Other lengths on request
Step gauges - Accessories – Evaluation software - Training - Calibration
Programing - Adaption of accuracy - Gear Measurement - Reverse Engineering - Freeform/Curve - Training
Value service
Visit us in Oberndorf - we are looking forward to
Industrie Team Service GmbHTeckstraße 13D-78727 Oberndorf am Neckar
Phone + 49 7423 / 8767-0Fax + 49 7423 / 2023Email [email protected] www.its-team.de
Industrie Team Service GmbH