Hypertech’s new product, the Interceptor, is asmart technology design that works with today’sgeneration of complex engine computers.The Interceptor easily mounts under the hood of avehicle and plugs into the factory connectorsto constantly monitor the vehicle’s functions.It then automatically recalculates the factory’scomputer performance calibrations with legendaryHypertech Power Tuning. This means morehorsepower and torque, quicker acceleration, betterdriveability, and improved MPG.

The Interceptor Controller easily installs under thehood in about fifteen (15) minutes. The InterceptorAccelerator Pedal Controller installs in the vehicle’sinterior on the driver’s side above the acceleratorpedal in about fifteen (15) minutes.

BEFORE installing the Hypertech Interceptor:Make sure the vehicle engine and ignition is turnedOFF prior to beginning the installation.

Mass Air Flow(MAF) Sensor

(5-Pin)

NOTE: Sensor locations may vary slightly depending on the application.

Underhood sensor locations for installing the Hypertech™ Interceptor™

Tools needed for Interceptor installation:• flashlight

Step-By-Step Installation Instructions For:2007-2014 Toyota Tundra 5.7 iForce, 2008-2014 Toyota Sequoia/Land Cruiser 5.7 iForce,& 2008-2014 Lexus LX570 5.7 iForce- Part #706001

Cam Sensor 1(3-Pin)

Cam Sensor 2(3-Pin)

Air FilterBox

Passenger SideOf Vehicle

Installing the Hypertech Interceptor Controller

Using the supplied Velcro, attach the Interceptor Controller on thepassenger side of the engine compartment as shown above.

Before proceeding to the next two (2) installation sections, lay out theInterceptor harness in the general areas of the sensor locations as shownin the engine compartment photo on page 1.

2

Hypertech has developed custom engine tuning for popular aftermarketair intakes for the Lexus/Toyota Truck/SUV 5.7 iForce. If you have oneof the aftermarket air intakes listed below on your vehicle, you will firstneed to use the Tuner Update Software on the provided CD and updateyour Interceptor Controller (NOT the Accelerator Controller) so youwill have the correct engine tuning to match the air intake installedon your vehicle.

To update, install the update software on the CD provided and save theprogram to your PC, connect your Interceptor Controller to your PC withthe supplied USB cable, follow a few simple instructions, and updateyour Interceptor with the correct new calibration for the air intakeinstalled on your vehicle. Then, proceed to install your Interceptor toyour vehicle. If you have the stock air intake installed, you will NOTneed to update your Interceptor and can proceed with the installation.

IMPORTANT NOTE: READ BEFORE INSTALLINGINTERCEPTOR TO YOUR VEHICLE

• AEM® Brute Force• aFe® Stage 2 & Stage 2Si• Airaid® air intake• K&N® 77 Series (metal)

• K&N® 63 Series (plastic)• Injen® Power-flow• RBP ™ air intake• Volant air intake

Air FilterBox

InterceptorController

Connecting the 5-Pin Mass Air Flow (MAF) Sensor

Air Intake

Disconnect the factory connector from the Mass Air Flow sensor.Push down on the connector, squeeze the release tab firmly, thenpull up to remove the connector.

Air FilterBox

Plug the Interceptor Mass Air Flow sensor connector into thevehicle Mass Air Flow sensor.

InterceptorMass Air Flow

Connector

Plug the Interceptor harness connector into the factoryMass Air Flow connector.

Factory Mass AirFlow Connector

InterceptorHarness

Connector

IMPORTANT NOTE

Make sure that the Interceptor harness and all connectors are clearfrom moving and/or rotating parts of the engine as well as any extremeheat sources.

3

Connecting the 3-Pin Cam Sensor

NOTE: There are two (2) cam sensors on the passenger side of thevehicle. The air intake and filter box in the above photo was removedto better show the locations of these sensors. Hypertech recommendsthat if you have the STOCK air intake and filter box on the vehicle,to use Cam Sensor 2. If you have an AFTERMARKET AIR INTAKEinstalled, Hypertech recommends using Cam Sensor 1. Theserecommendations are for ease of access ONLY with these air intakes.

CamSensor 1

CamSensor 2

Disconnect the factory connector from the cam sensor. Push downon the connector, squeeze the release tab firmly, then pull up toremove the connector.

CamSensor

Plug the Interceptor Cam sensor connector into the Cam sensor.

InterceptorCam SensorConnector

Connecting the 3-Pin Cam Sensor (Cont’d)

Plug the Interceptor harness connector into the factoryCam sensor connector.

FactoryCam SensorConnector

InterceptorHarness

Connector

Connecting the Interceptor Accelerator Controller

Plug the Interceptor Accelerator Controller cable into the AcceleratorController as shown above.

Using a flashlight, locate the factory accelerator harness connectorunder the driver’s dashboard and above the accelerator pedal.Disconnect the factory harness from the accelerator pedal sensorby pushing down on the connector, squeezing the release tabfirmly, then pulling up to remove the connector.

FactoryAccelerator

HarnessConnector

InterceptorAcceleratorController

InterceptorAccelerator

Controller Cable

IMPORTANT NOTE: READ BELOW BEFORE INSTALLINGINTERCEPTOR CAM SENSOR TO YOUR VEHICLE

IMPORTANT NOTE

Make sure that the Interceptor harness and all connectors are clearfrom moving and/or rotating parts of the engine as well as any extremeheat sources.

Connecting the Interceptor Accelerator Controller (Cont’d)

Plug the Interceptor accelerator pedal sensor connector into thefactory accelerator pedal sensor.

InterceptorAccelerator

Pedal SensorConnector

Factory AcceleratorPedal Sensor

Connector

InterceptorAccelerator

Pedal HarnessConnector

Plug the Interceptor accelerator pedal harness connector into thevehicle’s factory accelerator pedal sensor connector.

Tuck the Interceptor accelerator controller behind the carpet and consoleand out of the way of the accelerator pedal, making sure all otherwires/connectors are out of the way of the accelerator pedal as well.Installation is now complete! You are now ready to enjoy morepower and performance with the Hypertech Interceptor!

InterceptorAcceleratorController(Behind)

All Hypertech Power Tuning Products are warranted* against defects inmaterials or workmanship. Hypertech’s liability under this warranty shall belimited to the prompt correction or replacement of any defective part of theproduct which Hypertech, Inc. determines to be necessary. This LimitedLifetime Warranty is to the original purchaser for as long as he or she ownsthe vehicle on which the product is originally installed, providing all theinformation requested is furnished. You must retain a copy of your original salesinvoice or receipt. Without proper documentation, a service fee will be applied.Resold units are NOT covered under this warranty.

The 30-day money back guarantee applies to theInterceptor, Max Energy Power Programmer, E-CONEconomy Power Programmer, and the SpeedometerCalibrator. The product MUST be returned to the place ofpurchase within 30 days. All items must be received in anew, unused and ready-to-sell condition (including alloriginal packaging, parts, and paperwork) to receive arefund, excluding any shipping and handling fees.

30-Day Risk-Free, Money Back Guarantee

Product WarrantyFactory Direct Limited Lifetime Warranty

For more information, go to www.hypertech.com

3215 Appling Road • Bartlett, Tennessee 38133-3999Office Hours: 8am-5pm, Central Time, Mon.-Fri.

Tech: 901.382.8888 • Business: 901.385.1888 • Fax: 901.373.5290

11.13© 2013 Hypertech, Inc.

* Power Tuning products are Interceptors, Max Energy Power Programmers, E-CON Economy Power Programmers, Speedometer Calibrators, Power Tuning Modules, Power Chips, and Power Modules. Accessories such as Power caps, Power Coil kits, and fuel pressure regulators have a one (1) year warranty.