INSTALLATION GUIDE 1 INCH DRIVER BOX AND REMODEL BODY | ACROBAT

STEP 1 - MAKE ELECTRICAL CONNECTION

Black wire ( L. Line wire)White wire ( N. Neutral wire)Green wire ( G. Ground wire)

STEP 2 - PUT IN THE REMODEL HOUSING

VIEW OF RIGHTSIDE

Power for module

READ AND FOLLOW ALL SAFETY INSTRUCTION! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.

Never connect components under loadDo not touch the yellow surface of the LED as it maydamage the light engine

WARNING: RISK OF ELECTRIC SHOCK

Before installation, servicing, or peforming routinemaintenace disconnect power by turning o� the circuitbreakers both to the outlet box and to its associatedwall switchInstallation and service of luminaires should beperformed by a qualified licensed electrician in accordance with all local and National Electical CodesDO NOT install damaged productVerify that supply voltage is correct by comparing it with the luminaire label informationAll wiring connections should be capped with ULapproved recognized wire connectors

WARNING: RISK OF INJURY

Allow luminaire to cool before servicing andperforming maintenaceFollow all manufacturer’s warnings and restrictionsfor: driver type, mounting locations, replacement andrecyclingWear safety glasses and gloves when installing,maintaining or servicingAvoid direct eye exposure to the light source while itis on

Keep combustible material away from luminaireDo not install insulation within 3” (76mm) of any partof the luminaire or in a way that may entrap heat

WARNING: RISK OF FIRE

WARNING: RISK OF PRODUCT DAMAGE

1 INCH:(64 x 64mm)

2 in212 x2

11 INCH: 2 in (64mm)21

STEP 3 - INSTALL THE FLANGE

(Trimless)

INSTALLATION GUIDE 1 INCH DRIVER BOX AND REMODEL BODY | ACROBAT

STEP 2 - PREPARE THE MODULE

STEP 1 - MAKE ELECTRICAL CONNECTION AND INSTALL SAFETY HOOK

WARNING: DO NOT USE AS A HANGING DEVICE. DOING SO MAY RESULT IN DAMAGE OR INJURY

INSTALLATION GUIDE MODULE | ACROBAT

Step 2-1 :Release the Screws to this level.

Step 2-2 :Locate the tool into themodule.

Step 2-3 :Twist and lock the tool.

MODULE |

3A

INSTALLATION GUIDE ACROBAT

STEP 3 - INSTALL THE MODULE

Step 3-1 : Step 3-2 :Aline the modulewith the collar. (3A)

Insert the module tothe collar

Step 3-3 :Twist and lock themodule clockwise.(3B)

Step 3-4 :Tighten the screwsto secure the module. (3C)

Step 3-5 :Twist and releasethe tool anticlockwise.( )

3B 3C

MODULE |

4A

STEP 4 - TILT ANGLE ADJUSTMENT 0° ~ 40°

INSTALLATION GUIDE ACROBAT

Step 4-1 :Release this two Screws of Lock for Tilt.

Step 4-6 :Tight two Screws of Lock for Tilt.

Step 4-2 :Insert screwdriver throughthe first clip

Step 4-3 :Push the screwdriver to theheat sink

Step 4-4: Insert screwdriver through thesecond clip

Step 4-5 :Use the Screwdriver and adjust tilt angle, Scales on the two side of module. (4A)

MODULE |

Step 5-1 :Release the Screwof Lock for Rotation.

Step 5-2 :Adjust rotate.

STEP 5 - ROTATION ADJUSTMENT 360

Step 6-1 :Locate the lens into themodule.

Step 6-2 :Twist and lock the lens.

STEP 6 - INSTALL THE LENS

INSTALLATION GUIDE ACROBAT

Step 5-3 :Tighten the Screwof Lock for Rotation.

360º

A1_RM_Driver Box and RM body installationＭodule Installation_180327.pdf