Static Pass Box Controller Manual
Transcript of Static Pass Box Controller Manual
-
8/6/2019 Static Pass Box Controller Manual
1/8
Instruction Manual Ver1.1
STYRAX INSTRUMENTS INDIA PVT LTD
INSTRUCTION MANUALPASS BOX CONTROLLER DYNAMIC
MODEL NO: SPB105-S
VERSION: 1.1
Styrax Instruments India Pvt. Ltd.PLOT No.48-51,Dollapally,
Phase V Extn. I.D.A.,Jeedimetla, Hyderabad 055
Andhra Pradesh, INDIA
Ph: +91 40 2309 3314Fax: +91 40 2309 3315
www.styraxinstruments.com
Email: [email protected]
-
8/6/2019 Static Pass Box Controller Manual
2/8
Instruction Manual Ver1.1
Instrument SI. No :
STANDARD PACK
1) Instruction Manual --- 1 No
2) DPB105 Instrument --- 1 No
Checked By :
Date :
1.Description:
Pass box is used for material transfer from one Clean room to another clean room. It consists of a
rectangular box with two doors. The two doors are interlocked such that two doors cannot be open at the same
time, to prevent pressure losses and cross contamination.
Our Pass Box controller achieve this by preventing simultaneous access of door by ensuring that when one
door for a Pass box is open then other door is closed.
before opening of door.
1. When Door 1 is opened the display on the Door 2 will indicate No Go and at the Door 1 the display will
indicate Door Open
2. When any of the Door is kept open beyond a particular time say 10 min, a buzzer will be blown and the
display at the doors will indicate Close Door
3. When any door is opened the CF lamp is switched on, and the UV lamp will be switched off
4. Both Doors are provided with EM Locks
2. Features:
Advanced Micro controller based.
Supports Maximum of 2 doors
Supports Electro magnetic locks/Electric strikers
Door status indication with high intensity Bar LEDs
Status indication: GO, WAIT, DOOR OPEN, CLOSE DOOR
Buzzer output for door is kept open more than specified time from 2 to 30 min.
UV Lamp controlling
o UV Lamp ON for both Doors closed
o UV Lamp OFF for both Doors Open
-
8/6/2019 Static Pass Box Controller Manual
3/8
-
8/6/2019 Static Pass Box Controller Manual
4/8
Instruction Manual Ver1.1
5. Status Indication on Display Panel :
GO = Indicate that person can access the door.
WAIT = Indicate that person cannot access the door. DOOR OPEN = Indicate Door is opened
CLOSE DOOR = Indicates that the door is opened more than specified time.
6. OPERATING MODES:
MODE1: Normally Closed ( Default mode)MODE2: Normally Open
MODE1:
*Locking device is Electro magnetic lock or Electric striker.
Normally Close:
In this mode, initially both doors in locked condition. Door access by using push button. Status LEDs providedon the Display module indicates whether person can access the door or not.GO = GO LED glow indicates that person can access the door.WAIT = WAIT LED glow indicates that person cannot access the door.CLOSE DOOR = CLOSE DOOR LED indicates that the door is opened more than specified time (default time 2
min). When the door operated from open to closed condition, both doors locked for 4 sec, with in this time person
cannot access both doors. Door Buzzer time select from 2 - 30 min. Using jumpers (Refer Section 7.4)
Auto close time delay i.e. the time between the door release and energizing is 4 Sec
MODE2:
*Locking device is Electro magnetic lock or Electric striker.
Normally Open:
In this mode, initially both doors in un locked condition; here push buttons are used only for indication purpose
(no need to press the button). Status LEDs provided on the push button station indicates whether person canaccess the door or not.GO = GO LED glow indicates that person can access the door.WAIT = WAIT LED glow indicates that person cannot access the door.
CLOSE DOOR = CLOSE DOOR LED indicates that the door is opened more than specified time (default time 2min). When the door operated from open to closed condition, both doors locked for 4 sec, with in this time person
cannot access both doors. Door Buzzer time select from 2 - 30 min. Using jumpers (Refer Section 7.4)
Auto close time delay i.e. the time between the door release and energizing is 4 Sec
-
8/6/2019 Static Pass Box Controller Manual
5/8
Instruction Manual Ver1.1
7. Wiring diagram:
C UV CF LNEEML1-EML1+ FB1EML2- EML2+ FB2
FBFB+- FBFB+-
DOOR2 EM LOCK DOOR1 EM LOCKPower Supply
230V AC, 50Hz
CFLAM
P
UVLAM
P
L
N
1. Connect Door1 Display Module with Door1 Display Module Cable
2. Connect Door2 Display Module with Door2 Display Module Cable
8. MECHANICAL DRAWINGS
Fig (8.1) Figure for Installation of SPB105C-S Controller:
STYRAXINSTRUMENTS
INDIA PVT LTD
STATICPASSBOX CONT
ROLLER
-
8/6/2019 Static Pass Box Controller Manual
6/8
Instruction Manual Ver1.1
Fig (8.2) Front View Diagram of SPB105C-S Controller:
STYRAX INSTRUMENTS INDIA PVT LTD
STATIC PASS BOX CONTROLLER
230 mm
287mm
Fig (8.3) Figure for Installation of SPB105D Display Panel:
Pass Box
-
8/6/2019 Static Pass Box Controller Manual
7/8
Instruction Manual Ver1.1
Fig (8.4) Front View Diagram of SPB105D:
45mm
185 mm
OPEN
SPB105
9. Ordering Information:
I). Pass Box Controller
includes,
a. Controller:
Variants:
SPB105 X Model. No.
SPB105C S SPB105C-S
SPB105C D SPB105C-D
b. Pass Box Display Module:
Variants:
SPB105D X Model. No.
SPB105D X SPB105D -X
X
Model No Pass Box TypeS- Static
SPB105D- Dynamic
X
Model No Pass Box Type
S- StaticSPB105C
D- Dynamic
SPB105D X
Model No Future Use
SPB105D X
-
8/6/2019 Static Pass Box Controller Manual
8/8
Instruction Manual Ver1.1
NOTE:
For Further Information Contact:
Styrax Instruments India Pvt. Ltd.PLOT No.48-51, Dollapally, Phase V Extn. I.D.A., Jeedimetla, Hyderabad 055
Andhra Pradesh, INDIAPh: +91 40 2309 3314, Fax: +91 40 2309 3315
www.styraxinstruments.com
Email: [email protected]