STAHLWILLE angle-controlled torque wrenches. For absolute … · 2019. 12. 9. · STAHLWILLE...
Transcript of STAHLWILLE angle-controlled torque wrenches. For absolute … · 2019. 12. 9. · STAHLWILLE...
5
202
210
206
Torque
Tightening angle
Tolerance range
Snug point
Target torque
Target angle
Advance warning limit for torque
STAHLWILLE angle-controlled torque wrenches. For absolute accuracy.
1 Accurate control: Uncertainty is reduced to a minimum to
guarantee accurate readings.
1 Higher quality bolted connections: Including the
tightening angle as the second measured quantity makes
the bolted joint even more secure.
1 Perfect procedures: Easily readable, unmistakeable
displays and automatic switch-over to angle-controlled
measurement once the target tightening torque has been
reached – key features in efficient, safe work practice.
1 Excellent economy: Thanks to the considerably extended
measuring range, every angle-controlled torque wrench
can replace as many as four mechanical torque wrenches
(two indicating and two clicking), which simultaneously
reduces the costs of maintenance, calibration and
adjustment. All these models are suitable for clockwise
and anticlockwise tightening.
1 Better monitoring: All our angle-controlled torque
wrenches have a logging function. Using the
corresponding software (in some cases this is an optional
extra), it is possible to read out programmed, stored
readings and archive them on the PC – for example by
the serial number of the tool, date and timestamp of the
tightening operation, target torque and angle and the
torques and angles actually recorded.
The torque reading specifies how much force was applied to
tighten a fastener. For many applications, this is perfectly
good enough. However, in certain cases, the additional
measure of accuracy is an essential requirement. The
tightening force that is generated between the workpieces in
a bolted joint has to be exactly adhered to: if the force is too
great, there is a risk of breakage. If it is too low, on the other
hand, the connection will not be firm enough and may lead
to failure in the assembly under normal operating conditions.
Since the tightening force is dependent on the tightening
torque and the angle, measuring equipment that can measure
both quantities exactly is required. For applications of this
kind, STAHLWILLE has precisely the solutions industry needs.
Sensotork® 713R/712R
MANOSKOP® 714
MANOSKOP® 730D+ Angle Module 7395-1
For high-accuracy applications – Category A bolted connections, for example – just checking the torque is not enough.
As well as the torque, it is crucial to tighten to the correct tightening angle
201
202
5
2
3
4
1
1 2
6Benefits at a glance:
1 Indicating and click-type
1 Displays the torque actually applied after the wrench cuts out. In this way, the user has the
opportunity to optimise his or her working methods.
1 Units of measurement: N·m / ft·lb / in·lb
1 Automatic keypad lock
1 Display also works for anticlockwise torque
1 Angle-controlled measurement without a reference arm using a supplementary module
1 Overload protection by means of acoustic and visual signals
1 Automatic compensation to achieve correct tightening torque even if a changed extension is
entered
1 Different tolerance limits can be set for each joint
1 Visual red and green signals in the display confirm the status of the joint
1 Additional security for presets using PIN code
1 Automatic notification of the next calibration date
1 Deviation of indication ± 2%
Measure, cut-out and record: When the preset torque is reached, the torque wrench cuts out
and indicates this fact to the user via a definite tactile and audible signal. The tightening
torques are stored. The data can be transferred to a PC for evaluation and documentation.
MANOSKOP® 730DElectromechanical torque wrench
The square drive enables a broad range of insert tools
Dual stop signal with tactile and acoustic cut-out signals
Easy-to-read display
Rapid setting
The convenient keypad enables the torque wrench to be quickly and easily set
Torque tools
203
5
5
6
7
8
9
7 8
9
3 4
5
!
9
Power supply two 1.5 V AA batteries
Angle controlled tightening
Simply attach the Angle Module No 7395-1 and connect the cable to the interface
Data output USB interface
2-component handle has ergonomically designed, green softer layers and is
resistant to oils, grease, fuels, brake fluids and Skydrol.
QuickRelease safety lock
7395-1
Also available with adaptor for 22 x 28 mm
1 Tighten large torques effortlessly
1 High long-term durability
1 650 – 1000 N·m
Further details
on page 204
5
Torque tools
204
Service work & series production MANOSKOP® – indicating and click-type1 tactile and acoustic trigger signal1 mount for interchangeable insert tools1 QuickRelease safety lock1 fast setting using convenient keypad1 automatic compensation to achieve correct
tightening torque even if a changed extension isentered
1 overload protection by means of acoustic andvisual signals
1 automatic keypad lock prevents inadvertentchanges
1 angle-controlled measurements without areference arm using Angle Module No 7395-1 (refer to page 205)
1 display also works for anticlockwise torque1 units of measurement: N·m, ft·lb, in·lb1 different tolerance limits can be set for each joint1 visual red and green signals in the display confirm
the status of the joint
1 additional security for presets (function mode,trigger or preset value, unit of measurement,tolerance, save, deviating extension) using PIN code
1 up to 7.500 measurements can be stored1 USB interface1 automatic notification of the next calibration date1 calibration using perfectControl calibrating unit
No 7794 or calibration system No 77061 two-component handle with ergonomically
designed green softer layers (resistant to oils,grease, fuels, brake fluids and Skydrol)
1 with certificate1 in sturdy plastic case (sizes 40-100 in steel case)1 patent1 supplied with two 1.5 V AA batteries. AA/LR6, 1.2
V rechargeable cells may also be used1 display deviation value ± 2%, ± 1 digit
Basic wrenches with tool carrier for insert tools730D
'
Setting/display resolution J b h L LF SF R R gCode size W W W N·m ft·lb in·lb mm mm mm mm mm mm g with box'
96 50 17 10 10 10–100 N·m 7.4–75 ft·lb 90–900 in·lb 0.2/0.1 0.2/0.1 2/1.0 ; 28 23 467 426.5 17.5 1085 151096 50 17 20 20 20–200 N·m 15–150 ft·lb 180–1800 in·lb 0.5/0.1 0.5/0.1 5/1.0 , 28 23 548 515 25 1361 189696 50 17 40 40 40–400 N·m 30–300 ft·lb 360–3600 in·lb 1.0/0.1 1.0/0.1 10/1.0 , 28 23 688 655 25 1765 515596 50 17 65 65* 65–650 N·m 48–480 ft·lb 580–5800 in·lb 1.0/0.1 1.0/0.1 10/1.0 , 30.6 25.6 870 837 25 3300 60001
96 50 19 65 II/65 65–650 N·m 48–480 ft·lb 580–5800 in·lb 1.0/0.1 1.0/0.1 10/1.0 . 30.6 25.6 892 889 55 3224 750096 50 20 80 80 80–800 N·m 60–600 ft·lb 720–7200 in·lb 1.0/1.0 1.0/1.0 10/1.0 . 30.6 25.6 1160 1157 55 4577 1050096 50 21 00 100 100–1000 N·m 74–750 ft·lb 900–9000 in·lb 1.0/1.0 1.0/1.0 10/1.0 . 30.6 25.6 1344 1341 55 4995 11000'
* recommended ratchet insert tool No 735/40HD'
Basic wrenches with ratchet insert tool730DR
'
Setting/display resolution J D R R gCode size W W W N·m ft·lb in·lb mm " g with box'
96 50 18 10 10 10–100 N·m 7.4–75 ft·lb 90–900 in·lb 0.2/0.1 0.2/0.1 2/1.0 ; 1/2 1232 165796 50 18 20 20 20–200 N·m 15–150 ft·lb 180–1800 in·lb 0.5/0.1 0.5/0.1 5/1.0 , 1/2 1663 219896 50 18 40 40 40–400 N·m 30–300 ft·lb 360–3600 in·lb 1.0/0.1 1.0/0.1 10/1.0 , 3/4 2232 472296 50 18 65 65 65–650 N·m 48–480 ft·lb 580–5800 in·lb 1.0/0.1 1.0/0.1 10/1.0 , 3/4 3767 65301
96 50 20 65 II/65 65–650 N·m 48–480 ft·lb 580–5800 in·lb 1.0/0.1 1.0/0.1 10/1.0 . 3/4 3994 900096 50 18 80 80 80–800 N·m 60–600 ft·lb 720–7200 in·lb 1.0/0.1 1.0/0.1 10/1.0 . 3/4 6492 1250096 50 18 00 100 100–1000 N·m 74–750 ft·lb 900–9000 in·lb 1.0/0.1 1.0/0.1 10/1.0 . 3/4 6910 12500'
215-221
5
205
USB adaptor, jack cable and softwareNo 7732 for No 730D
7759-3
'
L RCode m g'
96 58 36 27 1.5 137'
Angle Module for No 730D7395-1Patents applied for, angle-controlled measurement without a referencearm. For torque wrench No 730D (sizes 10-65) from software release1.5.8. Torque wrenches No 730D fitted with older releases of the softwarecan be upgraded. Simply attach the module and connect to the torquewrench interface and the No 730D can be used for angle controlledtightening. The measurements are read off and settings made via thetorque wrench.When the preset snug point is reached, the torque wrench automaticallyswitches over to angle-controlled measurement in degrees. Depending on the options selected, the torque wrench will either cut outwhen the preset angle is reached or an alarm is heard. One 1.5 V battery is included in the package. Deviation of indication ± 1%.
'
RCode g'
96 58 36 28 387'
USB adaptor7757-1
'
RCode g'
52 11 10 57 10'
Jack cable7751with jacks at both ends, 90° angled.
'
L RCode m g'
52 11 00 51 1.5 50'
Documentation and management of readings on a PC1 Read out stored wrench data and joint readings:
- Joint identifier- Tool serial number- Date and time of tightening operation- Target torque or target angle- Torque level at which the tool cuts out - Tightening torque or angle reached- Tolerances- Joint evaluation
1 Storage of joint data in a database1 Delete or print highlighted joints from the database1 Export displayed joint data to a CSV file (compatible with Excel)1 13 languages1 User management1 Define new PIN1 Delete joint data stored in wrench
System requirements:1 PC1 Microsoft Windows 98 SE or compatible operating system with USB
support1 USB connection1 Installed ODBC driver for Access data
5
2
3
4
5
6
1
206
Benefits at a glance:
1 Indicating and click-type
1 4 measuring methods (torque, angle, torque backed up by angle, angle backed up by torque)
1 Freely configurable menu structure
1 Includes SENSOMASTER software for easy configuration of the tool
1 3 function modes: click-type, peak (indicating mode displaying peak reading) and
track (indicating mode displaying current value)
1 Angle-controlled measurement without a reference arm
1 Data storage (≤ 2,500 tightening jobs)
1 Acoustic and visual assessment of the joint
1 Clockwise and anticlockwise tightening
1 Tactile and acoustic trigger signals
1 Torque and angle are simultaneously visible
1 All readings are independent of the point of application of force with sizes 1, 2 and 4
1 Display deviation value ± 2 % for torque and ± 1% for angle
High-definition graphical colour display with additional side-mounted indicator
lamps
Automatic key-lock prevents inadvertent changes
Fast, accurate setting via keypad
Own ident number can be stored in the wrench
Indicator lamps clearly visible from all sides
Yellow light: advance warning threshold reached
Green light: within the target range
Red light: reading is outside the tolerance range
In a sturdy plastic case with foam inlays (sizes 40–100 in steel case)
With certificate
MANOSKOP® 714Electromechanical angle-controlled torque wrench
Torque tools
5
7
8
9
10
11
12
10
9
6
8
1
4 5
2 3
!
7
207
Also available with adaptor for 22 x 28 mm
1 Tighten large torques effortlessly
1 High long-term durability
1 650 – 1000 N·m
Optional extras: Li-Ionen battery No 7195-2 and charger No 7160
Individually configurable menus
Micro USB interface
Battery compartment with smooth-action bayonet fitting
Up to 200 joints can be programmed in up to 25 sequences
The wrench reminds the user automatically when calibration is due –
either by the number of joints or the time interval
No 7195-2
No 7160
Further details
on page 208
5
Torque tools
208
MANOSKOP® 714 – indicating and click-typeElectromechanical angle-controlled torque wrench1 4 measuring modes (torque, angle, torque backed
up by angle, angle backed up by torque)1 high-definition colour display with additional side-
mounted indicator lamps1 freely configurable menu structure1 optionally: Li-ion battery No 7195-2 and charger
No 71601 3 function modes: cut-out,
peak (indicating mode with peak value) and track (indicating mode with current value)
1 Micro USB interface1 bayonet connection for battery compartment1 QuickRelease safety lock change system for
insert tools1 angle-controlled measurement without a reference
arm1 Data storage (<_ 2500 tightening jobs)1 as many as 200 joints can be programmed in up to
25 preset sequences.1 different tolerance limits can be set for each joint1 acoustic and visual assessment of the joint1 rapid, accurate setting via keypad1 the automatic keypad lock prevents inadvertent
changes1 overload protection by means of acoustic and
visual signals and a fail-safe system (clockwise)1 automatic notification of the next calibration date,
either by the number of joints or the time interval1 fully automated calibrating and adjusting using the
perfectControl calibrating and adjusting unit No 7794-2 (torque) or 7794-3 (torque and angle)
1 units of measure: N·m, ft·lb, in·lb.1 tightening torque is automatically corrected if a
deviating extension is entered1 immediately reusable after release1 clockwise and anticlockwise tightening – it may be
necessary to refit the insert tool rotated through180° for anticlockwise tightening in the cut-outmode
1 tactile and acoustic trigger signal.1 torque and angle are simultaneously visible1 all readings are independent of the point of
application of force (with sizes 1, 2 and 4)1 safe handling due to ergonomically designed
handle (resistant to oils, grease, fuels, brake fluidand Skydrol)
1 2 certificates (torque, angle)1 in sturdy plastic case (size 40-100 in steel case)1 design patent, patent1 supplied with SENSOMASTER Basic software,
USB cable, 4 AAA/LR03 micro-batteries, 1.5 V. AAA, 1.2 V, micro NiMH rechargeable batteries can be used
1 display resolution, angle 0.1°1 display deviation value, angle ±1%, ±1 digit1 display resolution, torque <_ 60 N·m: 0.01 N·m;
> 60 N·m: 0.1 N·m1 display deviation value, torque ±2%, ±1 digit
Basic wrenches with tool carrier for insert tools714
'
J b h L LF SF R R gCode size W W W mm mm mm mm mm mm g with box'
96 50 09 01 1 1–10 N·m 0.7 –7.5 ft·lb 9–90 in·lb ; 28 23 226 188 17.5 370 79596 50 09 02 2 2–20 N·m 1.5–15 ft·lb 18–180 in·lb ; 28 23 226 188 17.5 380 80596 50 09 04 4 4–40 N·m 3–30 ft·lb 36–360 in·lb ; 28 23 252 214 17.5 420 84596 50 09 06 6 6–60 N·m 4.5–45 ft·lb 54–540 in·lb ; 28 23 393 355 17.5 810 12351
96 50 09 10 10 10–100 N·m 7.4–75 ft·lb 90–900 in·lb ; 28 23 466 428 17.5 1085 165596 50 09 20 20 20–200 N·m 15–150 ft·lb 180–1800 in·lb , 28 23 547 516 25 1361 189696 50 09 40 40 40–400 N·m 30–300 ft·lb 360–3600 in·lb , 28 23 687 656 25 1765 515596 50 09 65 65 65–650 N·m 48–480 ft·lb 580–5800 in·lb . 30.6 25.6 890 890 55 3222 70001
96 50 09 80 80 80–800 N·m 60–600 ft·lb 720–7200 in·lb . 30.6 25.6 1158 1158 55 4572 1040096 50 01 00 100 100–1000 N·m 74–750 ft·lb 900–9000 in·lb . 30.6 25.6 1343 1343 55 4990 10500'
215-221
5
209
Basic wrenches with ratchet insert tool714R
'
J D R R gCode size W W W mm " g with box'
96 50 10 01 1 1–10 N·m 0.7–7.5 ft·lb 9–90 in·lb ; 1/4 432 85796 50 10 02 2 2–20 N·m 1.5–15 ft·lb 18–180 in·lb ; 1/4 442 86796 50 10 04 4 4–40 N·m 3–30 ft·lb 36–360 in·lb ; 1/4 482 90796 50 10 06 6 6–60 N·m 4.5–45 ft·lb 54–540 in·lb ; 3/8 965 13901
96 50 10 10 10 10–100 N·m 7.4–75 ft·lb 90–900 in·lb ; 1/2 1232 165796 50 10 20 20 20–200 N·m 15–150 ft·lb 180–1800 in·lb , 1/2 1663 219896 50 10 40 40 40–400 N·m 30–300 ft·lb 360–3600 in·lb , 3/4 2275 566596 50 10 65 65 65–650 N·m 48–480 ft·lb 580–5800 in·lb . 3/4 5137 90001
96 50 10 80 80 80–800 N·m 60–600 ft·lb 720-7200 in·lb . 3/4 6487 1230096 50 11 00 100 100–1000 N·m 73–735 ft·lb 885-8850 in·lb . 3/4 6905 12500'
SENSOMASTER Live software7732-2
1 Record tightening operations with the MANOSKOP® 714.1 Representation of torque over time, angle over time, torque over angle.1 Representation of several curves simultaneously.1 Data export for further processing.1 The software is for a single-seat licence.1 Torque wrenches 714/1 … /100 must have firmware version 02.01.02.
'
RCode g'
96 58 52 35 111'
Li-ion battery for No 7147195-2
'
RCode g'
54 10 11 95 100'
Charging dock for Li-ion battery No 7195-2
7160
including chargerInput: 100 V–240 V AC ,Output: 4.2 V DC,with interchangeable socket adaptors.
'
RCode g'
54 10 00 60 200'
Docking station for No 7147762stationary base for securelyconnecting angle-controlled torquewrench No 714 to a PC via a USBport.
'
RCode g'
52 11 00 62 421'
Rest for docking station No 77627762-1for securely supporting long angle-controlledtorque wrenches No 714 from size 6 up.
'
RCode g'
52 11 01 62 520'
Interface adaptor set7761/3
'
RCode g'
96 52 11 61 446'
required for automated calibration and adjustment of angle-controlledtorque wrench No 714 using calibrating and adjusting units perfectControlNo 7794-2 and 7794-3.ContentsNo 7761 interface adaptorNo 7752 spiral cableNo 7760 mains adaptor
max. charge voltage 4.2 V,capacity 2600 mAh
5
210
Sensotork® 713RElectronic angle-controlled torque wrench
Benefits at a glance:
1 Angle-controlled measurements without a reference arm
1 Broad measuring range (5% – 100% of rated value)
1 Extremely wide range of angle measurement
1 Units of measurement N·m / ft·lb / in·lb
1 Clockwise and anticlockwise use
1 For use with all insert tools 9x12 and 14x18 mm
1 QuickSelect rapid recall of predefind sets of operating parameters
1 Defined sequence – a number of repeated joints can be grouped as
1 a defined sequence
1 Readings can either be directly stored, transmitted to the PC or simply displayed
1 Password protection tamper proof use
1 Freely selectable names for each series of test
1 Various languages available
1 Works-specific identifier
1 Programmable via PC
1 Resistant to oils, grease, fuels, brake fluids and Skydrol
1 Wide range of application: –20°C to +60°C
1 Meets requirements of DKD-R 3-7, Class 2
1 Deviation of indication ± 1%
Torque tools
5
2
3
4
5
6
1
5
4
1
6
2 3
!211
Warning signals: acoustic (buzzer), tactile (vibration in the handle), visual (LEDs and
display). The point at which the warning signal is triggered can be freely set
Amazingly simple handling
All functions are selected using the arrow keys. The visual guidance system makes
operation a simple matter
Measurements independent of the point of application of force (sizes 6 and 20)
Easy extension setting
Where the insert tool requires an extension adjustment, simply enter the new
value. Recalculation using complicated formulae is no longer necessary
Data output USB interface
QuickRelease
Firm locking and rapid change of any insert tools
Further details
on page 212
5
Torque tools
212
Electronic angle-controlled torque wrench Sensotork® 713R1 simple, flexible operation thanks to operator
guidance on large-format display1 very broad measuring range
(5% to 100% of rated value)1 supplied with insert tool reversible ratchet,
more insert tools1 QuickRelease safety lock1 for clockwise and anticlockwise torquing1 measurements independent of the point of
application of force (sizes 6 and 20)1 units of measurement: N·m, ft·lb, in·lb1 advance warning points programmable for visual,
tactile and acoustic signals1 torque and angle are simultaneously visible1 convenient angle measurement across a very wide
angle range without a reference arm1 insert tool lengths can be individually set1 maintenance friendly due to easy adjustment and
automatic reminder of next calibration date
1 repeated joints can be collated to form a singlemenu-guided sequence
1 individual identification markings possible1 password protection to prevent inadvertent
changes and make the tool tamper-proof 1 meets requirements of DKD-R 3-7, Class 2 1 with certificate1 in sturdy plastic case (size 40 in tough steel case)1 supplied with three 1.5 V AA batteries. AA/LR6,
1.2 V NiMH rechargeable cells may also be used.1 fully automated calibration (torque) using
perfectControl calibrating unit No 7794-2.Adjustment without disassembly.
1 registered design1 display deviation value for angle ± 1°1 display deviation value ± 1%
Electronic angle-controlled torque wrenches Sensotork®713R
'
D J b h L LF SF R R gCode size W W " mm mm mm mm mm mm g with box'
96 50 16 06 6 3–60 N·m 2.5–44 ft·lb 3/8 ; 50 33.5 378 299 17.5 856 150096 50 16 20 20 10–200 N·m 7–148 ft·lb 1/2 , 50 33.5 608 524 25 1552 243096 50 16 40 40 20–400 N·m 15–296 ft·lb 3/4 , 50 33.5 838 750 25 2332 5555'
Üü
Electronic torque wrench Sensotork® 712R
Electronic torque wrench Sensotork®712R/6
'
D J b h L LF SF R R gCode W W " mm mm mm mm mm mm g with box'
96 50 15 06 3–60 N m 2.5–44 ft.lb 3/8 ; 50 33.5 378 299 17.5 856 1500'
Üü
215-221
Registered design, electronic torque wrench with option of attaching interchangeable insert tools, same design as No 713 but without angle function.
5
213
Accessories for electronic angle-controlled torque wrench Sensotork® No 713Rand electronic torque wrench Sensotork® No 712R
USB adaptor, jack cable and software SENSOMASTER for No 712R, 713R7759-1for documenting and managing readings on a PC and carrying out statistical analyses.1 Read out stored wrench data and joint readings: Joint identifier, Tool serial number, Target torque or target angle, Torque level at which the tool cuts
out, Tightening torque or angle reached, Tolerances, Joint evaluation1 Storage of joint data in a database1 Delete or print highlighted joints from the
database1 Export displayed joint data to a CSV file
(compatible with Excel)1 13 languages1 User management1 Define new PIN1 Delete joint data stored in wrench
System requirements:1 PC1 Microsoft Windows 98 SE or compatible
operating system with USB support1 USB connection1 Installed ODBC driver for Access data
'
L RCode m g'
96 58 36 25 1.5 137'
USB adaptor7757-1
'
RCode g'
52 11 10 57 10'
Jack cable7751with jacks at both ends, 90° angled.
'
L RCode m g'
52 11 00 51 1.5 50'
Sensotork® 713R.The most accurate of them all.
5
Accessories
214
QuickRelease safety lock7161prevents insert tools being swapped.The system is locked in place on thehead of the torque wrench by meansof a safety screw. Once the protection system has beenfitted, it is possible to attach aninsert tool but not to remove itbecause the QuickRelease unlockbutton itself is locked. After the safety screw has beenremoved, the torque wrench revertsto being a standard, versatile tool.The safety screw can be fitted and removed using a TORX® screwdriverwith a central bore in the tip (No 4656, Size T20, Code 46 56 00 20) or aBITS screwdriver insert with a central bore in the tip (No 1442, Size T20,Code 08 16 00 20).
'
for torque wrenches RCode size No g'
54 10 00 70 1 714/1; 714/2; 714/4 454 10 00 71 2 712R/6; 713R/6; 714/6; 714/10;
730/10; 730a/10; 730N/10; 730Na/10; 730D/10 5
54 10 00 72 3 713R/20; 713R/40; 714/20; 714/40; 730/12; 730/20; 730/40; 730/65; 730a/12; 730a/20; 730N/12; 730N/20; 730N/40; 730N/65; 730Na/20; 730Na/40; 730D/20; 730D/40; 730D/65 11
54 10 00 73 4 U 730/5; 730N/5 21
54 10 00 74 5 U 714/65; 714/80; 714/100; 730II/65; 730NII/65; 730N/80; 730N/100; 730DII/65; 730D/80; 730D/100 15
'
for other torque wrenches on request.'
Plastic case, empty7301/7302for safe storage and transport oftorque wrenches (please order inlays separately).Supplied without torque wrench.
'
for torque wrenches L RCode No No mm g'
81 37 00 02 7301 712R/6; 713R/6; 714/1; 714/2; 714/4; 714/6; 714/10; 721/5; 721/15; 730/5; 730/10; 730/12; 730/20; 730a/5; 730a/10; 730a/12; 730a/20; 730N/5; 730N/10; 730N/12; 730N/20; 730Na/5; 730Na/10; 730Na/20; 730D/10 550 425
81 37 00 03 7302 713R/20; 714/20; 721/30; 730/40; 730N/40; 730Na/40; 730D/20 680 535
'
Inlays for plastic case'
for torque wrenches RCode No g'
83 07 10 04 712R/6; 713R/6; 721/5; 721/15; 730/5; 730/10; 730/12; 730/20; 730a/5; 730a/10; 730a/12; 730a/20; 730N/5; 730N/10; 730N/12; 730N/20; 730Na/5; 730Na/10; 730Na/20; 730D/10 88
83 07 10 02 713R/20; 721/30; 730/40; 730N/40; 730Na/40; 730D/20 113
'
LED lighting7396for torque wrenchesIf light is poor, simply attach thisLED lamp to illuminate the worksite.Included in the delivery is a 1.5 Vmicro battery. Supplied without torque wrench.
'
for torque wrenches RCode No g'
54 01 00 04 712R/6; 713R/6; 713R/20; 713R/40; 714/6; 714/10; 714/20; 714/40; 721/5; 721/15; 721/30; 730/5; 730/10; 730/12; 730/20; 730/40; 730a/5; 730a/10; 730a/12; 730a/20; 730N/5; 730N/10; 730N/12; 730N/20; 730N/40; 730Na/5; 730Na/10; 730Na/20; 730Na/40;730D/10; 730D/20; 730D/40 51
'i BITS1299for inside hexagon screws, for operating the adjusting screws on torque wrenches No 720, 721, 730 and 730N.
'
B outside L RCode mm E " mm g S'
08 09 00 02 2 C 6.3 1/4 34 4 10'
outside E DIN 3126/ISO 1173'
Torque angle gauges7380N/7385Nfor angle controlled bolt/screw tightening, with static read-off point. Read-off possible from any angle thanks to a pair of angled scales. Removable magnet for attaching sockets with 1/2" internal square drive.For use in conjunction with tightening tools such as Service MANOSKOP®No 730N. Since this tightening method requires a pre-determined snug torque to beapplied, it is essential to choose a torque wrench covering both snugtorque as well as maximum torque required to reach the recommendedtightening angle. Whether 1/2" or 3/4" sq.dr. Torque Angle Gauge is used depends upon the square drive of theappropriate torque wrench employed.
'
a D b h L RCode No " " W X mm mm mm g'
54 01 00 01 7380N 1/2 1/2 ± 360° 2° 78 43 416 49454 01 00 02 7385N 3/4 3/4 ± 360° 2° 78 76 416 720'