Stabilizers - · PDF fileMonitor 3-Axis Electronic Gyro Valve Drive J-Box Control Console...

4
Monitor 3-Axis Electronic Gyro Valve Drive J-Box Control Console J-Box Controller Stabilizers Western Marine Electronics 14120 NE 200th Street, Woodinville, WA 98072 (425)481-2296 [email protected] www.wesmar.com RS250 2.5 square feet 1.75 inch shaft 4801 Standard stabilize 4802 Stabilize with lift DSP 4800 3-Axis Control RS350 3.5 square feet 1.75 inch shaft CPS1000 Electronic Gyro Console SINGLE CYLINDER ACTUATOR FIN SIZES ELECTRONICS

Transcript of Stabilizers - · PDF fileMonitor 3-Axis Electronic Gyro Valve Drive J-Box Control Console...

Page 1: Stabilizers - · PDF fileMonitor 3-Axis Electronic Gyro Valve Drive J-Box Control Console J-Box Controller Stabilizers Western Marine Electronics 14120 NE 200th Street, Woodinville,

Monitor

3-Axis Electronic Gyro

Valve Drive J-Box

Control Console J-Box

Controller

Stabilizers

Western Marine Electronics 14120 NE 200th Street, Woodinville, WA 98072(425)481-2296 • [email protected] • www.wesmar.com

RS250 2.5 square feet 1.75 inch shaft

4801Standard stabilize

4802Stabilize with lift

DSP 4800 3-Axis Control

RS350 3.5 square feet 1.75 inch shaft

CPS1000Electronic Gyro Console

SINGLE CYLINDER ACTUATOR

FIN SIZES

ELECTRONICS

Page 2: Stabilizers - · PDF fileMonitor 3-Axis Electronic Gyro Valve Drive J-Box Control Console J-Box Controller Stabilizers Western Marine Electronics 14120 NE 200th Street, Woodinville,

TECHNICAL DRAWINGS

DSP DUAL CYLINDER

10-GALLON VERTICAL TANK 10-GALLON HORIZONTAL TANK

(Manifold can be side or bottom mounted)

Page 3: Stabilizers - · PDF fileMonitor 3-Axis Electronic Gyro Valve Drive J-Box Control Console J-Box Controller Stabilizers Western Marine Electronics 14120 NE 200th Street, Woodinville,

DIMENSIONAL ILLUSTRATIONS

RS250

RS350

FIN DIMENSIONS

SINGLE CYLINDER ACTUATOR ILLUSTRATION

Page 4: Stabilizers - · PDF fileMonitor 3-Axis Electronic Gyro Valve Drive J-Box Control Console J-Box Controller Stabilizers Western Marine Electronics 14120 NE 200th Street, Woodinville,

PRODUCT WARRANTYCommercial warranty and consumer limited warranty, disclaimer, and remedies. Seller warrants title, materials, and workmanship on equipment, except components manufactured by others for which seller assigns, as permitted, the original manufacturer’s warranty. Seller’s warranty period for all applicable express or implied warranties shall be ninety (90) days after installation or one (1) year after date of shipment to the original buyer, whichever time period expires first. Nonconforming equipment reported to seller during the applicable warranty period and returned to seller at buyer’s expense and risk shall be repaired, or replaced at seller’s option. If seller is unable or unwilling to repair or replace such reported and returned nonconforming equipment within a reasonable time, then buyer shall be entitled to a refund of the purchase price of the equipment as buyer’s sole remedy. This paragraph sets forth buyer’s exclusive remedies for nonconforming goods. This commercial warranty and consumer limited warranty is in lieu of all other warranties, express or implied, including design, course of dealing, merchantability, and fitness for a particular purpose.NOTE: LIMITATION OF SELLER’S COMMERCIAL AND CONSUMER LIABILITY.Seller shall not be liable on any claim for loss of use, revenue, or profit, for injury, or for any other incidental or consequential damages, regardless of the basis for buyer’s claim(s), including, but not limited to, the law of contract, warranty, or tort. In no case shall seller’s liability on any claim(s) exceed the amount paid to seller for the purchased goods.

Western Marine Electronics 14120 NE 200th Street, Woodinville, WA 98072(425)481-2296 • [email protected] • www.wesmar.com

Stabilization Information

Length ____________________ Beam ________________________ Draft ______________________

Weight _________________________ GM (Metecentric Height) ___________________________

Weight Short Tons ___________________________ Beam at Water Line ________________________

Full Speed (knots) __________________________ Cruise Speed _____________________________

Slowest speed in knots at which full Active stabilization is required ____________________________

At anchor stabilization required?________________________

Option for possible future upgrade to at anchor stabilization required?___________________

Engine Information

Main Engine Manufacturer(s) _____________________________ Model ________________________

Single Engine _____________ Twin Engine ______________ Other ____________________________

Idle Speed ____________________ Full Speed ____________________ HP ____________________

Transmission Manufacturer ______________________________ Model _________________________

PTO Size: SAE A_____ B_____ C_____: 2 Bolt ______ or 4 Bolt ______

Hydraulic System Information

Hydraulic Pump Location(s) ____________________________________________________________

Estimate area available in Front/Rear of pump drive _________________________________________

AC System Information

Single Phase __________________________ Three Phase ____________________________________

Genset Manufacturer __________________________________________________________________

Genset RPM _______________________ Hertz _______________________ Voltage ______________

Number of Control Stations _____________________________________________________________

SPECIFICATION SHEET

WESMAR STABILIZER SIZING CRITERIA