SSE Catalog
Transcript of SSE Catalog
-
w w w.FEMYERS.coM
MYERS
PROFESSIONAL SSE CATALOG PUMPS, TANKS, MoToRS AND coNTRoLS
-
ABoUT PENTAIR
The Premier Name in Quality Pumps Since 1870Myers was founded in 1870 by Francis and Philip Myers in Ashland, Ohio. The brothers began by building farm implements and then engineered and manufactured the first double-acting hand pump that delivered water on both the up and down strokes. From this modest beginning, the Myers pump line grew and evolved over the decades to include wastewater removal and industrial pumps and systems. In 1960 the Myers family sold the business to the McNeil Corporation of Akron, Ohio. In 1986 the business was acquired by Pentair, Inc. of St. Paul, Minnesota, where Myers is part of this $3 billion corporations water products group.
Myers is located on 80 acres in Ashland and operates in a modern 410,000 square foot manufacturing, distribution, foundry, and office facility, employing approximately 600 people dedicated to supplying top quality jet and submersible well pumps; utility, sump and sewage pumps; effluent pumps; non-clog and other large waste handling pumps; and high pressure reciprocating and centrifugal pumps and pumping systems for residential, agricultural, commercial, municipal and industrial applications for North America and more than 100 foreign countries.
The Myers Mission is to provide extraordinary, responsive service and quality products so that our customers find it easy to do business with us.
-
LIMITED WARRANTY SUMP & RESIDENTIAL SEWAGE
WARRANTY PERIOD
During the time periods and subject to the conditions hereinafter set forth, Myers will repair or replace to the original user or consumer any portion of your new Myers product which proves defective due to defective materials or workmanship of Myers. Contact your nearest Authorized Myers
Dealer for warranty service. At all times Myers shall have and possess the sole right and option to determine whether to repair or replace defective equipment, parts, or components. Damage due to lightning or conditions beyond the control of Myers is NOT COVERED BY THIS WARRANTY.
Pumps: 12/24 months depending on model; 18/30 months from date of manufacture.
Labor, etc. Costs: Myers shall IN NO EVENT be responsible or liable for the cost of field labor or other charges incurred by any customer in removing and/or re-affixing any Myers product, part or component thereof.
THIS WARRANTY WILL NOT APPLY: (a) to defects or malfunctions resulting from failure to properly install, operate or maintain the unit in accordance with printed instructions provided; (b) to failures resulting from abuse, accident or negligence; (c) to normal maintenance services and the parts used in connection with such service; (d) to units which are not installed in accordance with applicable local codes, ordinances and good trade practices; or (e) unit is used for purposes other than for what it was designed and manufactured, and (f) if three-phase submersible motors are installed on a single-phase power supply using a phase converter or if three-phase power is supplied by only two transformers, making an open Delta system.
RETURN OR REPLACED COMPONENTS: Any item to be replaced under this Warranty must be returned to Myers in Ashland, Ohio, or such other place as Myers may designate, freight prepaid.
PRODUCT IMPROVEMENTS: Myers reserves the right to change or improve its products or any portions thereof without being obligated to provide such a change or improvement for units sold and/or shipped prior to such a change or improvement.
WARRANTY EXCLUSIONS: Myers SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AFTER THE TERMINATION OF THE WARRANTY PERIOD SET FORTH HEREIN.Some states do not permit some or all of the above warranty limitations and, therefore, such limitations may not apply to you. No warranties or representations at any time made by any representative of Myers shall vary or expand the provisions hereof.
LIABILITY LIMITATION: IN NO EVENT SHALL Myers BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO ANY Myers PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY RESULT FROM IMPROPER INSTALLATION. Myers DISCLAIMS ALL LIABILITY, INCLUDING LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATIONMyers RECOMMENDS FOLLOWING THE INSTRUCTIONS IN THE INSTALLATION MANUAL. WHEN IN DOUBT, CONSULT A PROFESSIONAL.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
In the absence of suitable proof of the purchase date, the effective date of this Warranty will be based upon the date of manufacture.
DETERMINATION OF UNIT DATE OF MANUFACTURE: Submersible Sump Pump (8-95) month and year stamped on pump nameplate; Column Sump Pump month and year on red warranty tag.
1101 Myers Parkway Ashland, Ohio 44805888/987-8677 Fax: 800-426-9446
269 Trillium Drive Kitchener, Ontario, Canada N2G 4W5519/748-5470 Fax: 519/748-2553
For more information about Pentair Plumbing Products contact your local Myers Distributor, or our facilities in Ashland, Ohio.
-
2013 Pentair Ltd. All Rights Reserved. M9000SSE (01/10/13)
Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
293 WRIGHT STREET, DELAVAN, WI 53115 WWW.FEMYERS.COMPH: 888-987-8677 ORDERS FAX: 800-426-9446
-
UtILItY PUMPs 4-8MES106 2
MCU15/MCU15S/MCU20S Series 5
MUSP125 6
SPS-6 7
DU25 8
sUMP PUMPs 9-19MCSP Series 9
SP25 Series 10
S33 Series 11
SSM33I Series 12
MDC33/MDC50 Series 13
MCI033/MCI050 14
SX50 Series 15
DS Series 16
Sump Basin Package 17
ED-25 Sink Pump System 18
ED33 Series 19
eFFLUent PUMPs 22-32S40HT 22
S50HT Series 23
ME3 Series 24
ME40 Series 25
ME45 Series 26
ME Series 27
P50/P100 Series 28
MD Series 29
2NFL and J-BE Series 30
DE Series 32
seWAGe PUMPs 33-45SRM4 33
CMV5 34
MW50 35
MW Series 36
WHR Series 37
WHR5H-WHR20H Series 38
DSW Series 39
SR1830 40
CMV1830 41
SRM-BP BasinPro 42
CMV-BP BasinPro 43
MW-BP 44
MRJ 45
SRA Lift-out System 54
CE, CMEP and CMW 55
SMNO and SMNC Float Controls 56
PM15NO Pipe Mounted Mercury Float Controls 56
MFLC Wide-Angle Mechanical Float Controls 56
ALC-18 Piggyback Switches 56
20VM SJE Vertical Master Pump Switch 56
MFS Series Pump Switch 56
SA-1/OSA-1 Sump Alarms 57
CA-SS4 Alarm and Connection Box 57
Simplex, Duplex Structural Foam Junction Boxes 57
Iron Caulking & Compression-Type Hubs 57
Discharge and Conduit Flanges 57
Check Valves 57
Flexible Rubber Inlet Hubs 57
Basins and Covers 57
ACCessorIes 54-57
WAsteWAter PUMPs 50-513MW Series 50 3WHV Series 51
sPeCIAL PUrPose PUMPs 52-53Pro-Source Pumper 52 EPP Series Pump Control System 53
GRINDER PUMPS 41-44MRG20 46 MRGD200 48 Turnkey Simplex Basin Package 49GrInder PUMPs 46-49
BAtterY BACK-UP sUMP PUMPs 20-21 MBSP Series 20 MBSP-Plus Series 21
TABLE OF CONTENTS
-
UTILITY PUMPS
M9003sse
MES106Multi-Purpose Pump
Capacities 5 GPM 18.9 LPM
Shut-off head 10 3.1 m
Weight 4 lbs.
Liquids handling drain water
Intermittent liquid temp. 104 F 40 C
Motor air-cooled brush motor
Electrical data 115V, 2A, 1, 60Hz
Discharge Standard garden hose
Power cord 6
Ideal for transferring water, filling tanks and draining shallow flooded areas
Up to 5GPM with 10 head Connects to standard garden hose 115VAC with 9 power cord Removes standing water down to 1/8 depth Weighs only 4 lbs. Built-in carrying handle Includes 6 suction hose and floor drainer To operate, just attach a standard hose
to pump discharge and plug into any 115V outlet. Air-cooled, high-torque, non-submersible
motor with overload protection
sPeCIFICAtIons
FeAtUres
PAGE 4
-
UTILITY PUMPS
M9004sse
CAPACITY GALLONS PER HOUR
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER HOUR
20
16
12
8
4
0
6
5
4
3
2
1
0 25 75 10050 125 150 175 200
0 100 200 300 400 500 600 700
MCU20S
MCU15/MCU15S
CapacitiesMCU20SMCU15 / MCU15s
200 GPH120 GOH
757 LPH454 LPH
Shut-off headMCU20SMCU15 / MCU15S
2015
6.1 m4.6 m
Weight 3.25 lbs.
Liquids handling drain water
Intermittent liquid temp. 190 F 43C
Motor Bearingless sealed motor
Electrical data 115V, 1.45A, I, 60Hz
Dimensions 11 x 5 x 4-3/4
Discharge 3/8 i.d. plastic tubing (not included)
Tank capacity 2 Quarts
Housing ABS, high temp,.acid-resistant thermoplastic
Power cord 6
Ideal for the automatic removal of excess liquid which results from condensation
MCU15 / MCU15S / MCU20S SeriesCondensate Unit
sPeCIFICAtIons
FeAtUres
Advantages By Design Lifts to 20 (MCU20S)
Lifts to 15 (MCU15/15S) Built-in safety switch Low-profile unit,
only 4-3/4 high Thermal overload protection High temperature housing Built-in check valve Double-insulated enclosure
Provides longer life than similar size condensate units
Bearingless sealed motor offers a more reliable, longer life product
* For indoor use only
Applications Air conditioner Dehumidifier Icemaker High-efficiency furnaces Refrigeration systems Water coolers
CAPACITY GALLONS PER HOUR
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER HOUR
20
16
12
8
4
0
6
5
4
3
2
1
0 25 75 10050 125 150 175 200
0 100 200 300 400 500 600 700
MCU20S
MCU15/MCU15S
PAGE 5
-
UTILITY PUMPS
M9156sse
MUSP125Utility Sink Pump
Capacities 40 GPM 151.4 LPM
Shut-off head 14 4.27 m
Weight 15 lbs.
Liquids handling drain water
Intermittent liquid temp. up to 120 F up to 50 C
Motor 1/8 HP
Electrical data 115V, 4A, 1, 60Hz
Housing Thermoplastic
Power cord 8 three-prong, SJTW
Ideal for basement wet bars, laundry and utility sinks Designed to be used with a sink where gravity drain line
is not available Fully automatic operation Complete, compact system Easy to install - eliminates the need for traps,
vents and costly labor Quiet, trouble-free operation - easily mounts
beneath your sink Includes pump assembly, one-way valve, discharge
shut-off/flow balancing valve, strainer cup CSA listed
sPeCIFICAtIons
FeAtUres
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
14
12
10
8
6
4
2
00 5 10 15 25 30 403520
4
3
2
1
0
125 1501007550250
MUSP125 1/8 HP
PAGE 6
-
UTILITY PUMPS
M9005sse
Capacities 20 GPM 75.7 LPM
Shut-off head 22 6.7 m
Solids handling 1/8 3.18 mm
Liquids handling drain water
Intermittent liquid temp. up to 140 F up to 60 C
Motor 1/6 HP PSC
Electrical 115V, 2A, 1, 60Hz
Acceptable pH range 6-9
Discharge, garden hose adapter
3/4 threaded
19.05 mm threaded
Switch off/on manual
Housing flame-retardant polypropylene
Power cord 10, SJTW, SJTW-A
Mechanical seal type 11A, carbon & ceramic
SPS-61/6 HP Dewatering Utility Pump
sPeCIFICAtIons
FeAtUres
Ideal for light-duty drainage applications such as flooded basements, flat roofs and swimming pool covers
Draining small decorative pools (for repairs, painting)
Effective and easy to use Removes standing water
down to 1/8 depth Weighs only 9 lbs. Built-in carrying handle To operate, just attach
a standard hose to pump discharge and plug into any 115V outlet
Provides longer life than similar size dewatering pumps
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
22
20
18
16
14
12
10
8
6
4
2
00 4 8 12 16 20 24
7
6
5
4
3
2
1
0 15 30 45 60 75 90
SPS-6 1/6 HP
Efficient PSC motor uses only 2A
Air-filled motor housing; no oil required
Full mechanical shaft seal lasts ten times longer than lip seals
Built-in thermal overload protection
CSA Listed
PAGE 7
-
UTILITY PUMPS
M9006sse
DU251/4 HP Stainless Steel Utility Pump
sPeCIFICAtIons
Applications dewatering
Capacities 19 GPM 71.9 LPM
Shut-off head 23 7 m
Operations manual
Pump-down range 3/8 9.5 mm
Solids handling 1/8 3.2 mm
Liquids handling clear water
Continuous liquid temp. 77 F 22 C
Motor 1/4 HP, PSC
Electrical data 115V, 60Hz, 2.5A, 3450 RPM
Acceptable pH range 5-9
Mechanical seal dual lip seal with ceramic shaft sleeve
Housing stainless steel
Impeller polyphenylene oxide
Power cord 15 three-prong, SJTW 18-3
Discharge, NPT 1-1/4
Dimensions 9H x 7W
sPeCIFICAtIons
FeAtUres
Pumps up to 19 GPM Extra durable for
heavy-duty use Used for dewatering
shallow flooded areas such as basements, window wells, rooftops, ponds and stock tanks
1-1/4 NPT discharge
15 three-prong power cord
Includes 1 x 3/4 garden hose adapter
Pumps standing water down to 1/8
1-1/4 NPT x 1 NPT adapter Rated for continuous duty CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
20
15
10
5
0
6
4.5
3
1.5
0
0 15.1 30.2 49.2 71.9
0 4 8 13 19
DU25 1/4 HP
PAGE 8
-
SUMP PUMPS
M9007sse
Applications basement sumps
Capacities 50 GPM 189.3 LPM
Shut-off head 18 5.5 m
Operation: On Off
12-13 3-4.5
305-330 mm 76-144 mm
Solids handling 1/8 3.18 mm
Liquids handling drain water
Liquid temp. 77 F 25 C
Motor 1/3 HP
Electrical data 1625 RPM, 115V, 3.5A, 1, 60Hz
Acceptable pH range 6-9
Shaft seal none
Housing thermoplastic or cast iron
Power cord 6, 16/3, SJT
Discharge, NPT MCSP3: MCSP31:
1-1/4 1-1/2
31.8 mm 38.1 mm
Min. sump diameter 12 304.8 mm
MCSP Series1/3 HP Pedestal Sump Pumps
sPeCIFICAtIons
FeAtUres
Ideal for basements needing frequent drainage
Quick and easy installation Fits 12 diameter x 24
deep or larger sump pits Available with
corrosion-resistant thermoplastic or cast iron pump housing and base
Built-in reliability, ease of operation
Thermal overload protection to prevent motor overload
Top-mounted adjustable float switch for easy accessibility
Top-screened inlet to reduce clogging
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
20
16
12
8
4
0
6
5
4
3
2
1
0
17015013011050 90703010
0 5040302010
MCSP
PAGE 9
-
SUMP PUMPS
M9008sse
SP25 Series1/4 HP Residential Sump Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications basement sumps, dewatering
Capacities 32 GPM 121 LPM
Shut-off head 22 6.7 m
Operation: On Off
9.5 2.5
241 mm 63 mm
Solids handling 1/4 6.35 mm
Liquids handling drain water
Intermittent liquid temp up to 140F up to 60C
Motor 1/4 HP
Electrical data 115V, 6.5A, 1, 60Hz
Acceptable pH range 6-9
Shaft seal carbon/ceramic
Housing cast iron
Power cord 10, SJTW, SJTW-A
Discharge, NPT 1-1/2 38.1 mm
Min. sump diameter Wide Angle: Vertical:
18 10
457 mm 267 mm
sPeCIFICAtIons
FeAtUres
Versatility for many light-duty jobs
Designed for drain water removal or permanent applications with small amounts of debris
Durable construction to deliver many years of reliable service
Wide-angle or vertical mechanical switch
Dual ball bearing Powerful permanent split
capacitor run motor Built-in overload protection
Cast iron housing for superior heat dissipation
Non-clogging recessed impeller
Long-life carbon/ ceramic seal
Positive sealing, quick-disconnect power and switch cords make replacement simple
10 power cord Energy-saving,
low-amp motor CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
22
20
18
16
14
12
10
8
6
4
2
00 5 10 15 20 25 30
0 15 30 45 60 75 90 105 120
7
6
5
4
3
2
1
SP25A1 1/4 HP
PAGE 10
-
S33 Series1/3 HP Submersible Sump Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications basement sumps, dewatering
Capacities 32 GPM 121 LPM
Shut-off head 25 7.62 m
Operation: On Off
10.31 3.31
261 mm 84 mm
Pump-down range 7 178 mm
Solids handling 1/4 6.4 mm
Liquids handling drain water
Intermittent liquid temp up to 140F up to 60C
Motor 1/3 HP, PSC
Electrical data 3000 RPM, 115V, 6.5A, 1, 60Hz
Acceptable pH range 6-9
Shaft seal type 11A, carbon & ceramic, secondary lip seal
Housing cast iron
Power cord 10, 20
Discharge, NPT 1-1/2 38.1 mm
Min. sump diameter Float: Vertical:
18 10-1/2
457 mm 267 mm
sPeCIFICAtIons
FeAtUres
Versatility for many light-duty jobs
Designed for drain water removal or permanent applications with small amounts of debris
Maintenance-free operation Wide-angle or vertical
mechanical switch for small 10-1/2diameter sumps
Dual ball-bearing motor and additional lip seal provide durability and longer pump life
SUMP PUMPS
M9009sse
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
25
24
22
20
18
16
14
12
10
8
6
4
2
00 5 10 15 20 25 30
0 15 30 45 60 75 90 105 120
7
6
5
4
3
2
1
S33 1/3 HP
Durable PSC motor for years of service
Oil-filled PSC motor for maximum heat dissipation, continuous bearing lubrication
Recessed vortex impeller for free flow of liquids and solids
Thermal overload protection with automatic reset
CSA Listed
PAGE 11
-
SUMP PUMPS
M9010sse
SSM331 Series1/3 HP Cast Iron Submersible Sump and Effluent Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications basement sumps, dewatering, light effluent
Capacities 31 GPM 117 LPM
Shut-off head 23 7 m
Operation: On Off
9.94 4.06
252 mm 103 mm
Solids handling 1/2 12.7 mm
Liquids handling drainage effluent
Intermittent liquid temp up to 140F up to 60C
Motor 1/3 HP
Electrical data Shaded pole, 115V, 9A, 1, 60Hz
Acceptable pH range 5-9
Shaft seal type 11A, carbon & ceramic
Housing heavy cast iron
Power cord 10 (3 m), 16/3, SJTW, SJTW-A
Discharge, NPT 1-1/2
Min. sump diameter 12 304.8 mm
sPeCIFICAtIons
FeAtUres
Designed for light demanding drainage applications
Removal of drainage water and light septic tank effluent
Automatic and manual operation models available
Maintenance-free operation Piggyback wide-angle or
vertical mechanical switch Heavy-duty reliability
Oil-filled motor for maximum heat dissipation, continuous bearing lubrication
Recessed vortex impeller for free flow of liquids and solids
Thermal overload protection with automatic reset
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
22
20
18
16
14
12
10
8
6
4
2
00 5 10 15 20 25 30
0 15 30 45 60 75 90 105 120
7
6
5
4
3
2
1
SSM331 1/3 HP
PAGE 12
-
MDC33/MDC50 Series1/3 and 1/2 HP Cast Iron Submersible Sump Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications basement sumps, dewatering, light effluent, water transfer
Capacities 62 GPM 234 LPM
Shut-off head 32 9.75 m
Operation: Manual Tethered models: On Off Vertical models: On Off
12-1/2 3-1/2 6-1/2 2
318 mm 89 mm 165 mm 51 mm
Solids handling 1/2 12.7 mm
Liquids handling drainage effluent
Intermittent liquid temp 130F 54C
Motor electrical data 1/3 HP, 9.8A; 1/2 HP, 12A; shaded pole w/thermal overload protection,115V, 1, 60Hz, 1550 RPM
Acceptable pH range 6-9
Shaft seal carbon & ceramic
Housing heavy cast iron
Power cord 10 (3 m) or 20 (6 m), 16/3, SJTW, SJTW-A
Discharge, NPT 1-1/2
Min. sump diameter Float: Vertical:
14 10
356 mm 254 mm
sPeCIFICAtIons
FeAtUres
1/3 or 1/2 HP Rugged cast iron pump
body and motor cover, exterior hardware stainless steel construction
1-1/2 (38 mm) NPT discharge
Carbon/ceramic shaft seal Piggyback-style float
for automatic or manual operation
Oil-filled motor with automatic reset overload provides safe operation
Ball-bearing construction for long life
Easily replaceable power cord with optional lengths available
CSA Listed
SUMP PUMPS
M9011sse
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
40
30
20
10
0 20 8040 60
200150100500 250
10
8
6
4
2
0
MDC33 1/3 HP
MDC50 1/2 HP
PAGE 13
-
SUMP PUMPS
M9180sse
MCI033/MCI050 Series1/3 and 1/2 HP Cast Iron Submersible Sump Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications basement sumps, dewatering, light effluent, water transfer
Capacities 62 GPM 235 LPM
Shut-off head 32 9.8 m
Operation: On Off
9 4
229 mm 102 mm
Operation automatic
Solids handling 1/2 12.7 mm
Liquids handling drainage effluent
Continuous liquid temp 130F 54C
Motor electrical data 1/3 HP, 9.8A; 1/2 HP, 12A; shaded pole w/thermal overload protection, 115V, 1, 60Hz, 1550 RPM
Acceptable pH range 6-9
Shaft seal carbon & ceramic
Housing/volute heavy cast iron
Volute base fiberglass reinforced polypropylene
Impeller fiberglass-reinforced Noryl with threaded brass insert
Exterior hardware stainless steel
Power cord 10 (3 m) or 20 (6 m), 16/3, SJTW-A, SJTW
Discharge, NPT 1-1/2 38.1 mm
Min. sump diameter 10 25.4 cm
sPeCIFICAtIons
FeAtUres
2-pole switch design allows for operation in sump diameters of 10 or more
Rugged, oil-cooled motor provides continuous bearing lubrication and maximizes heat dissipation
Lubricated ball bearings and shaft seal for longer service life
Shaded pole motor eliminates failure-prone switches and relays
Long-life carbon/ceramic seal protects motor against water leakage
Heat sensor overload protection with automatic reset when motor cools to safe operating temperature
Anti-airlock hole in base reduces added labor
Pump intake screen, volute base, switch and power cord are serviceable
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
35
30
25
20
15
10
5
0
10
8
6
4
2
0
250200150100500
0 6040 7050302010
MCI033 1/3 HP
MCI050 1/2 HP
PAGE 14
-
SX50 SeriesExplosion-Proof 1/2 HP Submersible Sump Pump and Control Panel Package
sPeCIFICAtIonssPeCIFICAtIons
Applications class 1, division 1, group D hazardous locations
Capacities 95 GPM 360 LPM
Shut-off head 34 10 m
Operation: On/Off turns on/off with tethered switch hooked to control box
Solids handling (SX50; SX50H) 2 / 3/4 50 mm / 19 mm
Liquids handling domestic effluent & drain water
Intermittent liquid temp up to 140F up to 60C
Motorn electrical data 1/2 HP, 1750 RPM, 1 - capacitor start, 230V, 60Hz
Acceptable pH range 6-9
Winding insulation temp. (Class B)
266F up to 120C
Specific gravity .9-1.1
Viscosity 28 35 SSU
Discharge, NPT SX50: SX50H:
2 1-1/2
50 mm 38.1 mm
Min. sump diameter Simplex: Duplex:
24 36
61.0 mm 91.4 mm
sPeCIFICAtIons
FeAtUres
Rugged, submersible, explosion-proof sump pumps for municipal, commercial and industrial use
Constructed for use in Class 1, Division 1, Group D hazardous locations
Designed to pump contaminated water, with a wide range of pollutants listed under the CSA listings
Intrinsically safe control panel included
Durable motor will deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and constant bearing lubrication
Recessed impeller reduces radial bearing loads, increasing bearing life
SUMP PUMPS
M9015sse
High-torque capacitor start, single-phase motor for assured starting under heavy load
Seal leak probes warn of seal leak condition
On-winding heat sensors protect motor from overheating and prevent costly motor damage
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
40
35
30
25
20
15
10
5
0
12
10
8
6
4
2
00 10 20 30 40 50 60 70 80 90 100
0 50 100 150 200 250 300 350
SX50H
SX50
PAGE 15
-
SUMP PUMPS
M9016sse
DS Series1/3 through 3/4 HP Stainless Steel Sump Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications basement sumps, dewatering, utility
Capacities 45 GPM 170.3 LPM
Shut-off head 26 98.4 m
Operation: On Off
13 6.75
330 mm 171 mm
Solids handling 3/4 19 mm
Liquids handling drain water
Continuous liquid temp 104F 40C
Motor electrical data 1/3 HP, 2.7A; 1/2 HP, 4.8A; 3/4 HP, 6.4A; 115V; 60Hz, PSC Motor, 3450 RPM
Acceptable pH range 5-9
Shaft seal dual lip with ceramic shaft seal
Housing stainless steel
Power cord 15, SJTW, 18/3
Discharge, NPT 1-1/4
Min. sump diameter 12
sPeCIFICAtIons
FeAtUres
Used for dewatering from construction sites, ponds, pits, tanks and extracting water from foundations or flooded basements
1/3 HP, 1/2 HP and 3/4 HP available
PSC motor with self- lubricating ball-bearing construction
Double lip seals with ceramic wear surface
Passes 3/4 solids Piggyback-style float allows
for manual operation Includes 1-1/4 NPT x 1-1/4
NPT 90 discharge elbow, 1-1/4 NPT x 1-1/2 NPT adapter
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
30
25
20
15
10
5
0
9
7.6
6
4.5
3
1.5
00 5 10 15 20 25 30 35 40 45 50
0 19 38 57 76 95 114 133 152 170 190
DS33 1/3 HP
DS50 1/2 HP
DS75 3/4 HP
PAGE 16
-
PSB18221/4 HP Sump Basin Package
sPeCIFICAtIonssPeCIFICAtIons
Applications basement sumps, dewatering, new or existing installations
Capacities 32 GPM 121 LPM
Shut-off head 22 6.7 m
Operation: On Off
9.5 2.5
241 mm 63 mm
Solids handling 1/4 6.35 mm
Liquids handling drain water
Intermittent liquid temp up to 140F up to 60C
Motor electrical data 1/4 HP, 115V, 1, 60Hz
Shaft seal carbon & ceramic
Housing cast iron
Power cord 10, SJTW, SJTW-A
Discharge, NPT 1-1/2 38.1 mm
sPeCIFICAtIons
SUMP PUMPS
M9155sse
FeAtUres
1/4 HP Fully assembled check
valve includes Injection-molded structural
foam provides the highest quality construction for uniform wall thickness and strength
Proprietary flush mount design for easy shipping and storage allows for pallet stacking for sump
Basin Features: Radon proof radon
approved basin and cover for radon prevention
Injection-molded structural foam (polyethylene) 20-gallon capacity basin; standard 18 x 22 size
Injection-molded structural foam (polyethylene) lid; gas-tight single-piece design with seal
4 snap-in type hub adapter with stainless steel clamp; fits 4 DWV SCH. 40 plastic pipe
1-1/2 NPT threaded discharge and 2 NPT vent flange (easily converts to 3); comes with gas-tight cord grommet
Sump pump check valve fits 1-1/2 black, galvanized, and DWV SCH. 40 pipe
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
22
20
18
16
14
12
10
8
6
4
2
00 5 10 15 20 25 30
0 15 30 45 60 75 90 105 120
7
6
5
4
3
2
1
SP25A1 1/4 HP
Pump Only
PAGE 17
-
SUMP PUMPS
M9017sse
ED-251/4 HP Sink Pump System
sPeCIFICAtIonssPeCIFICAtIons
Applications laundry trays, washing machines, wet bars, water softeners, dehumidifiers, etc.
Capacities 32 GPM 121 LPM
Shut-off head 22 6.7 m
Operation: On Off
9.5 2.5
241 mm 63 mm
Solids handling 1/4 6.35 mm
Liquids handling drain water
Intermittent liquid temp up to 140F up to 60C
Motor electrical data 1/4 HP, 115V, 6.5A, 1, 60Hz
Shaft seal carbon & ceramic
Housing cast iron
Power cord 10 (3 m), SJTW, SJTW-A
Discharge, NPT 1-1/2
Min. sump diameter 10 254 mm
sPeCIFICAtIons
FeAtUres
Specially designed for many household jobs
Pumps water from laundry trays, washing machines, wet bars, water softeners, dehumidifiers, etc.
High-capacity 1/4 HP pump Oil-filled for maximum heat
dissipation and constant lubrication
Thermal overload protection with automatic reset
Fully assembled Includes discharge
pipe inside basin Installs above
floor no need for sump
Pump Only
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
22
20
18
16
14
12
10
8
6
4
2
00 5 10 15 20 25 30
0 15 30 45 60 75 90 105 120
7
6
5
4
3
2
1
ED25 1/4 HP
PAGE 18
-
ED33 Series1/3 HP Sink Pump System
sPeCIFICAtIonssPeCIFICAtIons
Applications laundry trays, wet bars, beautician or utility sinks, dehumidifier/air-conditioning units
Capacities 48 GPM 182 LPM
Shut-off head 24 7.3 m
Operation: On Off
6 1/2 2
165 mm 50 mm
Solids handling 1/2 12.7 mm
Liquids handling drainage effluent
Intermittent liquid temp 130F 54C
Motor electrical data 1/3 HP, 115V, 9.8 FLA, 1, 60Hz
Acceptable pH range 5-9
Shaft seal carbon & ceramic
Housing cast iron
Power cord 10 (3 m), grounded SJTW, SJTW-A
Discharge, NPT 1-1/2
sPeCIFICAtIons
FeAtUres
1/3 HP Pre-packaged sink/pump
system is ready for quick application
Basin Features: High-impact engineered
resin, exterior hardware and stainless steel construction
1-1/2 (38 mm) NPT discharge
Carbon/ceramic shaft seal Piggyback-style float for
automatic or manual operation
Oil-filled motor with automatic reset overload provides safe operation
Octagonal shape, compact size, 6-gallon useable capacity
Easily replaceable power cord with optional lengths available
Molded reuseable PNC gasket lid seal
Basin dimensions are 15-1/16 W x 13 3/8 H (11-9/16 from floor to center of inlet)
SUMP PUMPS
M9018sse
Pump Only
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
25
20
15
10
5
0 10 20 30 40 50
1000 5025 12575 150 175
7
6
5
4
3
2
1
0
ED33 1/3 HP
PAGE 19
-
BATTERY BACK-UP SUMP PUMPS
M9019sse
MBSP12 Volt Battery Standby Pump System
sPeCIFICAtIonssPeCIFICAtIons
Applications emergency dewatering
Capacities 30 GPM 114 LPM
Shut-off head 16 4.88 m
Liquids handling sump drain water
Intermittent liquid temp up to 77F up to 25C
Motor 12V DC, 9A
Charger plug-in type wall-mounted transformer; input - 120V AC, 60Hz, 15W; output - 12V AC, 60Hz, 2A
Check valve dual check valves provided
Housing thermoplastic
sPeCIFICAtIons
FeAtUres
Protects home if AC-powered pump fails
Backs up residential sump pump automatically during power outage or pump failure (primary pump and piping not included)
Reliable operation Continuous
self-charging system Solid-state controller
monitors battery charge and pump operation
Alarm sounds when standby pump activates
Controller includes connectors for pump, charger, float switch and battery*
Area light lights up dark, powerless work area
Works with flooded and sealed AGM deep cycle lead-acid battery
Re-settable circuit breaker eliminates the need for a fuse
2A 5-stage charger
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
0 105
70 90 110 130
15 20 25 30 35
16
14
12
10
8
6
4
2
0
503010
4.5
3.5
2.5
1.5
.5
MBSP 12V DC
* Deep cycle marine-type battery (Group 24) recommended not included with MBSP system
PAGE 20
-
BATTERY BACK-UP SUMP PUMPS
MBSP-Plus Series12 Volt Battery Standby Pump System
sPeCIFICAtIonssPeCIFICAtIons
Applications emergency dewatering
Capacities 2700 GPH 10,220 LPH
Shut-off head 18
Liquids handling sump drain water
Continuous liquid temp up to 77F up to 25C
Motor 12V DC, 18A
Charger fully automatic, computerized monitoring, control and alarm system; input - 115V AC, 60Hz; output - 12V AC, 8A (5 stages)
Check valve included
Housing thermoplastic
sPeCIFICAtIons
M9020sse
20
15
10
5
0 2512.5 37.5 50
50 100 15025 75 125 1756
5
4
3
2
1
0
0
MBSP-PLUS
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
FeAtUres
2700 GPH (10,220 LPH), 8A 5-stage charging system
Thermoplastic pump with steel case charger enclosure
1-1/4 (32 mm) NPT threaded discharge; adapts to 1-1/4 (32 mm) and 1-1/2 (38 mm) NPT
High volume ideal for active sump pits
8A multi-stage charging system (UL/CUL approved) with steel enclosure provides the strongest battery charge
Plug-in style connectors for quick and easy installation
Audio and visual alarms keep you informed of status at all times
Check valve and battery case included
Fits most new and existing sump pits
PAGE 21
-
EFFLUENT PUMPS
M9013sse
S40HTHigh Temperature 1/3 HP Effluent Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications boiler blow-down pits, condensate pits, hot water sumps
Shut-off head 21 6.4 m
Capacities 45 GPM 170 LPM
Operation (S40HT-11P): On Off
13.5 4.5
343 mm 114 mm
Operation manual or automatic
Solids handling 3/4 19 mm
Liquids handling high temperature liquids
Intermittent liquid temp. S40HT-11P S40HT-11
up to 194F up to 200F
up to 90C up to 93C
Motor electrical data 1/3 HP, oil-filled, thermal overload protection, 115V, 12A, 1, 60Hz, 1550 RPM
Acceptable pH range 6-9
Housing/volute case cast iron
Impeller cast iron
Exterior hardware stainless steel
sPeCIFICAtIons
FeAtUres
All cast-iron housing, volute case, and impeller resists the most extreme corrosive environments
Rugged-built, oil-filled motor for continuous bearing lubrication and maximum heat dissipation
Heat sensor overload protection with automatic reset when motor cools to a safe operating temperature
Lower ball bearing eliminates sleeve bearing wear and reduces motor wear
Non-clog vortex style impeller, ejector vanes for seal protection
Stainless steel hardware allows easy disassembly after extended service
Oil and water resistant cord design prevents oil loss from and moisture protection for motor
Bearings and mechanical seal are permanently lubricated for long life
Easy to service heavy-duty lift-out ring
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
24
20
16
12
8
4
0
7
6
5
4
3
2
1
1750 15025 100 12550 75
0 10 20 30 40 50
PERFORMANCE@ 70F WATERTEMPERATURE
PERFORMANCE@ 194F WATER
TEMPERATURE
S40HT
Mechanical seal type 7A or equal, Buna-N elastomers, carbon and ceramic sealing faces, stainless steel metal parts
Bearings lower ball, upper sleeve type, oil lubricated
Power cord 20, 16/3, SJOOW-A/SJOW
DIscharge, NPT 1-1/2 38.1 mm
Min. sump diameter Simplex: Duplex:
18 30
45.7 mm 76.2 mm
PAGE 22
-
EFFLUENT PUMPS
S50HT Series1/2 HP High Capacity Submersible Effluent Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications high-capacity sump, effluent, boiler blow-down
Capacities 100 GPM 378 LPM
Shut-off head 50 15.2 m
Max. spherical solids 3/4 19 mm
Liquids handling domestic effluent and drain water
Max. liquid temp. 200F 93CMotor electrical data 1/2 HP, 3450 RPM, PSC
with thermal overload, 115V, 12 FLA, 1, 60Hz
Acceptable pH range 5-9
Specific gravity .91.1
Viscosity 2835 SSU
Discharge, NPT 2 50.8 mm
Housing cast iron
Min. sump diameter Simplex: Duplex:
24 36
61.0 mm 91.4 mm
Power cord 20, 16/4, SOOW, SOOW-A
sPeCIFICAtIons
M9014sse
FeAtUres
1/2 HP Class 30 cast iron
construction 2 (50.8 mm)
NPT discharge Silicon carbide shaft seals Oil-filled motor with
automatic reset overload provides safe operation
Ball-bearing construction for long life
600V jacketed lead for added durability
Easily replaceable power cord with optional lengths available
CSA Listed
Mechanical seal type 7A or equal, Buna-N elastomers, carbon and ceramic sealing faces, stainless steel metal parts
Bearings lower ball, upper sleeve type, oil lubricated
Power cord 20, 16/3, SJOOW-A/SJOW
DIscharge, NPT 1-1/2 38.1 mm
Min. sump diameter Simplex: Duplex:
18 30
45.7 mm 76.2 mm
0 6030 90 120
0 100 200 300 400
16
12
8
4
0
60
45
30
15
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
S50 HT 1/2 HP PERFORMANCE@200F WATER
TEMPERATURE
S50 HT 1/2 HP PERFORMANCE@70F WATER TEMPERATURE
PW217-280 Control Panel Required
(sold separately)
PAGE 23
-
EFFLUENT PUMPS
M9021sse
ME3 Series1/3 HP High Head (ME3H) and High Flow (ME3F) Submersible Effluent Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications effluent removal, sump drainage, water transfer, flood control
Capacities ME3H: ME3F:
36 GPM 66 GPM
136 LPM 249 LPM
Shut-off head ME3H: ME3F:
35 31
10.7 m 9.5 m
Max. spherical solids 3/4 19 mm
Liquids handling domestic effluent and drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/3 HP, 1550 RPM, shaded pole,
oil-filled, 115V, 12A, 1, 60Hz, 230V, 6A, 1, 60Hz
Acceptable pH range 6-9
Specific gravity .91.1
Viscosity 28 35 SSU
Discharge, NPT 1-1/2 38.1 mm
Housing heavy cast iron
Min. sump diameter Simplex: Duplex:
24 36
61.0 mm 91.4 mm
Power cord 20, 16/3, SJTW
sPeCIFICAtIons
FeAtUres
Durable motor delivers years of reliable service
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
Overload protected, shaded pole motor eliminates starting switches and relays which are prone to fail
Heavy cast iron motor housing and volute case dissipate heat, allow motor to run cooler for extended life
Engineered for maintenance-free operation
Field-tested, wide-angle, mercury-free mechanical float switch for maximum drawdown (automatic piggyback models only)
Automatic pump models can be operated manually by unplugging piggyback switch and plugging pump directly into outlet
Passes full 3/4 solids
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
40
35
30
25
20
15
10
5
0
12
10
8
6
4
2
0
0 50 100 150 200 250 300 350
0 10 20 30 40 50 60 70 80 90 100
ME3F 1/3 HP
ME3H 1/3 HP
ME3F
ME3H
PAGE 24
-
EFFLUENT PUMPS
ME40 Series 4/10 HP Effluent and Drain Water Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications effluent removal, sump drainage, water transfer, flood control
Capacities 80 GPM 303 LPM
Shut-off head 32 9.75 m
Max. spherical solids 3/4 19 mm
Liquids handling domestic effluent and drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 4/10 HP: 1650 RPM, PSC,
oil-filled; 115V, 12A, 1, 60Hz; 230V, 6A, 1, 60Hz
Acceptable pH range 5-9
Specific gravity .91.1
Viscosity 2835 SSU
Discharge, NPT 1-1/2 38.1 mm
Housing cast iron
Min. sump diameter Simplex: Duplex:
24 36
61.0 mm 91.4 mm
Power cord 20, 16/3, SJTW
sPeCIFICAtIons
M9022sse
FeAtUres
Two-vane cast iron impeller design provides maximum dosing efficiency
Enclosed design for high- efficiency pumping
Eliminates possibility of jamming between impeller and volute
Passes full 3/4 solids Durable motor will
deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
Positive sealing, quick- connect float and switch cords make replacement simple if service is ever necessary
Field-tested, wide-angle, mercury-free mechanical float switch provides maximum drawdown (automatic models only)
Lower ball bearing and heavy-duty, type 6 seal for added pump life
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
40
35
30
25
20
15
10
5
0
12
10
8
6
4
2
0
0 50 100 150 200 250 300 350
0 10 20 30 40 50 60 70 80 90 100
ME40 4/10 HP
NEW! noW WItH CAST IRON IMPELLER For Added dUrABILItY
PAGE 25
-
EFFLUENT PUMPS
M9185sse
ME45 Series1/2 HP Effluent and Drain Water Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications effluent removal, sump drainage, water transfer, flood control
Capacities 87 GPM 329 LPM
Shut-off head 44 13.41 m
Max. spherical solids 3/4 19 mm
Liquids handling domestic effluent and drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/2 HP: 3450 RPM, PSC,
oil-filled; 115V, 8.6A, 1, 60Hz; 230V, 4.3A, 1, 60Hz
Acceptable pH range 5-9
Specific gravity .91.1
Viscosity 28 35 SSU
Discharge, NPT ME40: ME45:
1-1/2 2
38.1 mm 50.8 mm
Housing cast iron
Min. sump diameter Simplex: Duplex:
24 36
61.0 mm 91.4 mm
Power cord 20, 16/3, SJTW
sPeCIFICAtIons
FeAtUres
Two-vane cast iron impeller design provides maximum dosing efficiency
Enclosed design for high- efficiency pumping
Eliminates possibility of jamming between impeller and volute
Passes full 3/4 solids Durable motor will deliver
many years of reliable service
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
Positive sealing, quick- connect float and switch cords make replacement simple if service is ever necessary
Field-tested, wide-angle, mercury-free mechanical float switch provides maximum drawdown (automatic models only)
Lower ball bearing and heavy-duty, type 6 seal for added pump life
CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
50
40
30
20
10
0
15
12
9
6
3
0
0 50 100 150 200 250 300 350
0 10 20 30 40 50 60 70 80 90 100
ME45 1/2 HP
PAGE 26
-
EFFLUENT PUMPS
ME Series1/2 through 1-1/2 HP Effluent Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications effluent removal, sump drainage, water transfer, flood control
Capacities 120 GPM 454 LPM
Shut-off head 95 28.9 mm
Max. spherical solids 3/4 19 mm
Liquids handling domestic effluent and drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/2 HP, 115V, 1, 1/2 to
1-1/2 HP, 230V, 1, 208/230/ 460/575V, 3, oil-filled, permanent split capacitor type, 1, 3450 RPM, 60Hz
Acceptable pH range 6-9
Specific gravity .91.1
Viscosity 2835 SSU
Discharge, NPT 2 50.8 mm
Housing cast iron
Min. sump diameter Simplex: Duplex:
24 36
61.0 mm 91.4 mm
Power cord 10
sPeCIFICAtIons
M9023sse
FeAtUres
Ideal for use in mound and trench pressure distribution systems
High-efficiency, two-vane, enclosed impeller provides ideal performance for efficient dosing
Impeller passes full 3/4 solids
Enclosed impeller design eliminates the possibility of jamming or corrosion between impeller and volute
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
100
90
80
70
60
50
40
30
20
10
0
28
24
20
16
12
8
4
0
0 50 100 150 200 250 300 350 400 450
0 10 20 30 40 50 60 70 80 90 100 110 120 130
ME150 1-1/2 HPME100 1 HPME75 3/4 HPME50 1/2 HP
Durable motor will deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and constant bearing lubrication
High-torque, permanent split capacitor (PSC), single- phase motors; no starting switches or relays to wear out
Optional seal leak probe warns of seal leak condition (dual seal motors only); helps prevent costly motor damage
Motors have a winding current and temperature- sensitive overload (single phase only)
Volute seal ring is replace-able; restores pump to original performance if wear should occur
Motor is held in place by 4 screws; easily removed if service is ever needed
CSA Listed
PAGE 27
-
EFFLUENT PUMPS
M9024sse
P50/P100 Series1/2 and 1 HP Effluent ST.E.P. Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications effluent removal, sump drainage, water transfer, flood control
Capacities 60 GPM 227 LPM
Shut-off head 124 37.8 m
Max. spherical solids 3/4 19 mm
Liquids handling domestic effluent and drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/2 HP, 115V or 230V, 1;
1 HP, 230V, 1, oil-filled, permanent split capacitor type, 3450 RPM, 60Hz
Acceptable pH range 6-9
Specific gravity .91.1
Viscosity 28 35 SSU
Discharge, NPT 1-1/2 38.1 mm
Housing cast iron
Min. sump diameter Simplex: Duplex:
24 36
61.0 mm 91.4 mm
Power cord 20, 14/3 SJOW, SJOW-A
sPeCIFICAtIons140
120
100
80
60
40
20
0
40
36
32
28
24
20
16
12
8
4
00 5 10 15 20 25 30 35 40 45 50 55 60
25 50 75 100 125 150 175 200 225
P51 & P52 1/2 HP
P102 1 HP
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
FeAtUres
P Series effluent pumps are designed for years of maintenance-free operation
Single-vane, enclosed impeller provides steep, non-overloading performance curve for pressure collection and ST.E.P. systems; out-performs most pumps in its class
Enclosed impeller eliminates the possibility of jamming or corrosion between impeller and volute
Passes 3/4 spherical solids Durable motor will
deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
High-torque, permanent split capacitor (PSC), single-phase motors; no starting switches or relays to wear out
Double tandem seal configuration for extra motor protection, tough effluent pumping applications
Optional seal leak probes warn of seal leak condition; helps prevent costly motor damage
On-winding current and temperature-sensitive overload to protect against costly burnout
Volute seal ring is replaceable; restores pump to original performance if wear should occur
Motor is held in place by 4 screws; easily removed if service is ever needed
CSA Listed
PAGE 28
-
EFFLUENT PUMPS
MD Series1/2 HP On-site Effluent Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications on-site filtered effluent, cistern
Capacities 2 35 GPM 7.6 132.5 LPM
Shut-off head 75225 22.9 68.6 m
Max. spherical solids .080 2.0 mm
Liquids handling filtered effluent
Max liquid temp. 86F 30CMotor electrical data Dry-wound, double ball bearing,
double-seal, thermal overload protected, 115V, 1, 60Hz
Specific gravity .91.1
Viscosity 2835 SSU
Discharge, NPT 1-1/4
Housing stainless steel and composite
Power cord 10 30 m
300V, 2-wire with ground, SJTW-A, SJTW
sPeCIFICAtIons
M9026 sse
FeAtUres
1/2 HP, 115V, single-phase Superior drawdown
capability to 4-1/2 (114 mm) vs. 13-1/2 (343 mm) on a standard NEMA 4
25% reduced amp-draw 9.5A vs. 12.7A on a standard NEMA 4
Cooler and quieter operation eliminates expensive flow-inducer sleeves
Stainless steel and composite construction
Exclusive dry-run capability Enclosed and self-lubricated
shaft-bearing resists wear from abrasives
Heavy 7/16 (12 mm) positive drive 300 Series stainless steel hexagonal shaft
Serviceable composite intake screen allows for 0.80 solids
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
0 15
300
225
150
75
30 45 60
0 100
80
60
40
20
0
25 50 75 200
30 GPM 1/2 HP
10 GPM 1/2 HP
20 GPM 1/2 HP
PAGE 29
-
EFFLUENT PUMPS
M9027sse
2NFL and J-BE Series1/2 through 1-1/2 HP High Head Filtered Effluent Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications on-site filtered effluent
Capacities 50 GPM 189 LPM
Shut-off head 480 146.30 m
Max. spherical solids 1/16 1.6 mm
Liquids handling filtered effluent
Max liquid temp. 122F 68CMotor electrical data 1/2 HP, 115V, 1, 1/2 to 1-1/2 HP,
230V, 1, 60Hz, 3450 RPMSpecific gravity .91.1
Viscosity 28 35 SSU
Discharge NPT 8, 12, and 20 GPM: 25 and 35 GPM:
1-1/4 2
31.8 mm 50.8 mm
Housing stainless steel
Power cord 10, 30, 50 or 100, jacketed, 14/3, SOOW
sPeCIFICAtIons
FeAtUres
Cost-effective wastewater systems High-pressure capacity Corrosion-resistant design for long life Dependable field proven motor Stainless steel construction Built-in overload protection Replaceable 10, 30, 50 or 100 jacketed power cord Hermetically sealed windings Continuous-duty rating Frequent cycling capabilities Powerful, yet lightweight Easy handling and installation
2NFL J-BE
(Performance charts on following page)
PAGE 30
-
EFFLUENT PUMPS
2NFL and J-BE Performance
M9027sse
500
400
300
200
100
0
CAPACITY LITERS PER MINUTE
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
TOTA
L H
EAD
IN M
ETER
S
150
120
90
60
30
3/4 HP
1/2 HP
1 HP
0 2 4 6 8 10 12 14 16 18 20
8 15 23 30 38 45 53 60 68 75
8 GPM 2NFL
500
400
300
200
100
0
CAPACITY LITERS PER MINUTE
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
TOTA
L H
EAD
IN M
ETER
S
150
120
90
60
30
3/4 HP
1 HP
0 2 4 6 8 10 12 14 16 18 20
8 15 23 30 38 45 53 60 68 75
1/2 HP
12 GPM 2NFL
0 3 6 9 12 15 18 21 24 27 30
11 23 34 45 57 68 80 91 102 114
1-1/2 HP
1 HP
3/4 HP
1/2 HP
500
400
300
200
100
0
CAPACITY LITERS PER MINUTE
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
TOTA
L H
EAD
IN M
ETER
S
150
120
90
60
30
20 GPM 2NFL
0 5 10 15 20 25 30 35 40 45 50
19 38 57 76 95 114 133 151 170 189
1-1/2 HP
1/2 HP
1 HP
500
400
300
200
100
0
CAPACITY LITERS PER MINUTE
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
TOTA
L H
EAD
IN M
ETER
S
150
120
90
60
30
25 GPM J-BE
0 5 10 15 20 25 30 35 40 45 50
19 38 57 76 95 114 133 151 170 189
CAPACITY LITERS PER MINUTE
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN F
EET
TOTA
L H
EAD
IN M
ETER
S
250
200
150
100
50
0
75
60
45
30
15
1 HP
1-1/2 HP
35 GPM J-BE
PAGE 31
-
EFFLUENT PUMPS
M9028sse
DE Series 4/10 and 1/2 HP Stainless Steel Continuous Duty Effluent Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications residential and commercial applications
Capacities 97 GPM 367 LPM
Shut-off head 36 11 m
Max. spherical solids 1-1/2 38 mm
Liquids handling domestic effluent and drain water
Continuous liquid temp. 130F 54CMotor electrical data 4/101/2 HP, 115V; 4/10 HP,
10.5A; 1/2 HP, 12A; 60Hz
Acceptable pH range 5-9
Specific gravity .91.1
Viscosity 28 35 SSU
Discharge NPT 2 50 mm
Housing stainless steel
Min. sump diameter Simplex: Duplex:
18 24
46 mm 60 mm
Power cord 20, SJOW, 16 AWG
sPeCIFICAtIons
FeAtUres
Pumps up to 97 GPM (1/2 HP) and 92 GPM (4/10 HP) Designed to quickly clear water or effluent PSC motor with self-lubricating ball-bearing construction Ideal for residential and commercial applications Tethered float switch Double-lip seal with ceramic wear surface Suitable for continuous use Includes 90 discharge elbow CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
0 25 50 75 100
0 375 18
15
12
9
6
3
0
30075 150 225
DE50 1/2 HPDE40 4/10 HP
0
15
30
45
60
PAGE 32
-
SRM4 4/10 HP Sewage Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage, high-capacity sump, effluent
Capacities 95 GPM 360 LPM
Shut-off head 19 5.8 m
Solids handling 2 50.8 mm
Liquids handling septic effluent and sewage
Intermittent liquid temp up to 140F up to 60CMotor electrical data 4/10 HP, PSC, 115V, 12A, 1, 60Hz
Acceptable pH range 5-9
Discharge, NPT 2 50.8 mm
Housing heavy cast iron
Power cord 10 (20 optional)
Impeller recessed, thermoplastic
Volute case cast iron
Shaft seal type 11A, carbon & ceramic
sPeCIFICAtIons
M9029sse
FeAtUres
Power for versatile applications Residential septic tank sewage Large sumps Long-lasting performance Oil-filled motor for maximum heat dissipation
and continuous bearing lubrication Recessed vortex impeller for free flow of liquids,
solids up to 2 diameter Rotary shaft seal has carbon and ceramic faces
for positive seal Thermal overload protection with automatic reset CSA Listed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
24
20
16
12
8
4
00 10 20 30 40 50 60 70 80 90
7
6
5
4
3
2
1
40 80 120 160 200 240 280 320 360
SRM4 4/10 HP
SEWAGE PUMPS
PAGE 33
-
SEWAGE PUMPS
M9030sse
CMV51/2 HP Residential Sewage Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage, high-capacity sump, effluent
Capacities 95 GPM 360 LPM
Shut-off head 18 shut-off: 19 shut-off:
5.5 m 5.8 m
Solids handling 2 50.8 mm
Liquids handling raw sewage, effluent and drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/2 HP, PSC, 1625 RPM, 115V,
12A, 1, 60HzAcceptable pH range 6-9
Discharge NPT 2 50.8 mm
Housing cast iron
Power cord 20, 16/3, SJTW
Impeller recessed, thermoplastic
Volute case thermoplastic
Shaft seal type 11A, carbon & ceramic
Min. sump diameter Simplex: Duplex:
18 30
457 mm 762 mm
sPeCIFICAtIons
FeAtUres
Engineered for many years of maintenance-free operation
Wide-angle, mercury-free mechanical float switch for maximum drawdown
Recessed vortex impeller operates completely out of volute and provides free flow through passage for solids and liquids
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
20
15
10
5
0
6
5
4
3
2
1
0
0 50 100 150 200 250 300 350
0 10 20 30 40 50 60 70 80 90 100
CMV5 1/2 HP
Durable motor will deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
Recessed vortex impeller provides minimal radial loading for long bearing life
CSA Listed
PAGE 34
-
SEWAGE PUMPS
MW501/2 HP Residential and Light Commercial Sewage Pump
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage, high-capacity sump, effluent
Capacities 135 GPM 510 LPM
Shut-off head 27 8.23 m
Solids handling 2 50.8 mm
Liquids handling domestic sewage & drain water
Intermittent liquid temp up to 140F up to 60CMotor electrical data 1/2 HP, 1625 RPM, PSC (1),
oil-filled, 115V, 9A, 1, 60Hz; 230V, 4.5A, 1, 60Hz
Acceptable pH range 5-9
Discharge, NPT 2 50.8 mm
Housing class 30 cast iron
Power cord 20, 16/3, SJTW
Impeller thermoplastic
Volute case cast iron
Shaft seal type 6, carbon & ceramic
Min. sump diameter Simplex: Duplex:
24 36
61.0 cm 91.4 cm
sPeCIFICAtIons
M9031sse
FeAtUres
Two-vane impeller design provides maximum pump efficiency
Enclosed design for high-efficiency pumping
Eliminates possibility of jamming between impeller and volute
Passes full 2 solids Original performance can
be restored if wear occurs by replacing volute seal ring
Low-amp draw from the efficient PSC motor means less heat build-up
CSA Listed
Durable motor will deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
High-torque, permanent split capacitor (PSC) motors; no starting switches or relays to wear out
Field-tested, wide-angle, mercury-free piggyback mechanical float switch provides maximum drawdown (automatic models only)
Long, flexible type 6 seal provides high-pressure sealing with improved seal face protection by location
Lower ball bearing eliminates sleeve bearing wear and significantly reduces motor wear
30
25
20
15
10
5
00 20 40 60 80 100 120 140
10
8
6
4
2
0
0 100 200 300 400 500
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
MW50 1/2 HP
PAGE 35
-
SEWAGE PUMPS
M9032sse
MW Series 2" Solids Handling Heavy-Duty Residential and Commercial Sewage Pumps Available with Single or Double Seals
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage, high-capacity sump, effluent
Capacities 165 GPM 624 LPM
Shut-off head 70 21.3 m
Solids handling 2 50.8 mm
Liquids handling domestic sewage & drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/2 to 2 HP, 208/230V, 1;
208/230/460/575V, 3, oil-filled, permanent split, capacitor type, 1, 3450 RPM, 60Hz
Acceptable pH range 5-9
Discharge, NPT 2 50.8 mm
Housing cast iron
Power cord 10
Impeller ductile iron
Volute case class 30 cast iron
Shaft seal type 21, carbon & ceramic
Min. sump diameter Simplex: Duplex:
24 36
61.0 cm 91.4 cm
sPeCIFICAtIons
FeAtUres
High head performance for demanding applications
High-efficiency, two-vane, enclosed impeller for high- efficiency pumping
Eliminates possibility of jamming between impeller and volute
Original performance can be restored if wear occurs by replacing volute seal ring
Durable motor will deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
High-torque, permanent split capacitor (PSC) single-phase motors; no starting switches or relays to wear out
CSA Listed
80
70
60
50
40
30
20
10
0
20
15
10
5
00 20 40 60 80 100 120 140 160 180
0 100 200 300 400 500 600
MWH50 1/2 HP
MW200 2 HP MW150 1-1/2 HP
MW100 1 HP
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
PAGE 36
-
SEWAGE PUMPS
WHR Series 2" Solids Handling Heavy-Duty Residential and Commercial Sewage Pumps Available with Single or Double Seals
sPeCIFICAtIonssPeCIFICAtIons
Applications domestic wastewater and septic systems
Capacities 178 GPM 673.8 LPM
Shut-off head 33 10.1 m
Solids handling 2 50.8 mm
Liquids handling drain water and domestic sewage
Intermittent liquid temp up to 140F up to 60CMotor electrical data 1/2 HP, 115V, 1, 60Hz, PSC;
1/2, 3/4, 1 HP, 230V, 1, 60 Hz PSC; 200/230/460/575V, 3, 60Hz
Acceptable pH range 5-9
Discharge, NPT 2 3
50.8 mm 76.2 mm
Housing cast iron
Power cord WHRSJOW/SJOW-A 20, 16/3, 1; 20, 16/4, 3 WHR-DS 20, 14/4, 1 20, 14/3, 1, L/D; 20, 16/4, 3, L/D
Impeller cast iron, vortex
Volute case cast iron
Shaft seal single type 21, carbon/ceramic, double tandem carbon/ceramic
Min. sump diameter Simplex: Duplex:
24 30
61.0 cm 76.0 cm
sPeCIFICAtIons
M9033sse
FeAtUres
Power range meets many applications
Domestic wastewater and septic systems
Light commercial sewage High-capacity fluid transfer Durable motor for
long-lasting performance 1/2, 3/4 and 1 HP models
Oil-filled for cooler operation and constant bearing lubrication
Single-phase PSC motors eliminate starting switches
Recessed impeller increases bearing life
Thermal overload protection with automatic reset
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
32
28
24
20
16
12
8
4
0
9.6
8.4
7.2
6.0
4.8
3.6
2.4
1.2
0 20 40 60 80 100 120 140 160 180
76 152 228 304 380 456 532 608 684
WHR10 1 HP & WHR10-DS WHR7 3/4 HP & WHR7-DS WHR5 1/2 HP & WHR5-DS
Double seal models with seal leak detector are not CSA Listed
PAGE 37
-
SEWAGE PUMPS
M9034sse
WHR5H-WHR20H Series2" Solids Handling Residential and Commercial Sewage and Effluent Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications domestic wastewater and septic systems
Capacities 218 GPM 825 LPM
Shut-off head 70 20.9 m
Solids handling 2 50.8 mm
Liquids handling raw sewage and sewage effluent
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/2, 1, 1-1/2 & 2 HP, 3450 RPM,
200/230V, 1, 60 Hz, PSC; 200/230/460V, 3, 60Hz
Acceptable pH range 6-9
Discharge NPT 2 3
50.8 mm 76.2 mm
Housing cast iron
Power cord 20, 16/3, SJOW/SJOW-A, 1 20, 16/4, SJOW/SJOW-A, 3
Impeller ductile iron, vortex
Volute case cast iron
Shaft seal type 21, carbon & ceramic
Min. sump diameter Simplex: Duplex:
24 30
61.0 cm 76.0 cm
sPeCIFICAtIons
FeAtUres
Higher heads for demanding applications
Domestic wastewater and septic systems
Light commercial sewage High-capacity fluid transfer Durable motor for
long-lasting performance 1/2, 1, 1-1/2
and 2 HP models
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
70
60
50
40
30
20
10
0
20
15
10
5
0 20 40 60 80 100 120 140 160 180 200 220 240
100 200 300 400 500 600 700 800 900
WHR5H 1/2 HP
WHR10H 1 HP
WHR15H 1-1/2 HP
WHR20H 2 HP
Oil-filled for cooler operation and constant bearing lubrication
Single-phase PSC motors eliminate starting switches
Recessed impeller reduces radial loads and increases bearing life
Thermal overload protection with automatic reset
CSA Listed
PAGE 38
-
SEWAGE PUMPS
DSW Series 2" Solids Handling Continuous Duty Stainless Steel Sewage Pumps
sPeCIFICAtIonssPeCIFICAtIons
Applications domestic wastewater and septic systems
Capacities 145 GPM 549 LPM
Shut-off head 42 12.8 m
Solids handling 2 50.8 mm
Liquids handling sewage, wastewater, effluent
Continuous liquid temp 130F 54CMotor electrical data 4/10 HP, 1/2 HP, 115V
1/2 HP, 1 HP, 230V 1 HP, 460V, 3
Acceptable pH range 5-9
Discharge, NPT 2 w/90 elbow
Housing stainless steel
Power cord 20', SJOW, 16 AWG
Impeller stainless steel
Volute case stainless steel
Shaft seal mechanical carbon & ceramic
sPeCIFICAtIons
M9035sse
FeAtUres
Pumps up to 145 GPM (1 HP), 114 GPM (1/2 HP) and 103 GPM (4/10 HP)
Designed for reliable pumping of wastewater
Stainless steel, corrosion-resistant shaft and hardware
Oil-cooled and lubricated, continuous-duty PSC motors
Silicon carbide or carbon ceramic mechanical seals
Tethered float switches feature piggyback controls
20 power cord Suitable for continuous use Includes 90
discharge elbow CSA Listed
0 75.7 151.4 227.1 302.8 378.5 454.2 529.9 605.6
0 20 40 60 80 100 120 140 160
DSW100 1 HP 460/3DSW100 1 HP 230V
DSW50 1/2 HP 230V DSW50 1/2 HP 115V
DSW40 4/10 HP 115V
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
45
40
35
30
25
20
15
10
5
0
13.7
12
10.6
9
7.6
6
4.5
3
1.5
0
PAGE 39
-
SEWAGE PUMPS
M9036sse
SR1830 4/10 HP Packaged Simplex Sewage System
sPeCIFICAtIonssPeCIFICAtIons
Applications residential septic tank sewage and large sumps
Capacities 95 GPM 360 LPM
Shut-off head 19 5.8 m
Solids handling 2 50.8 mm
Liquids handling septic effluent and sewage
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 4/10 HP, shaded pole,
115V, 12A, 1, 60HzAcceptable pH range 5-9
Discharge NPT 2 50.8 mm
Housing heavy cast iron
Power cord 10 (20 optional)
Impeller recessed, thermoplastic
Volute case cast iron
Shaft seal type 11A, carbon & ceramic
sPeCIFICAtIons
FeAtUres
Complete package for versatile applications
Residential septic tank sewage
Large sumps High-quality system
includes SRM4AIC sewage pump
4/10 HP, 115V, 12A, 1, 60Hz motor
2 diameter discharge Oil-filled motor for
max imum heat dissipation and continuous bearing lubrication
Recessed vortex impeller for free flow of solids up to 2 diameter
Rotary shaft seal has carbon and ceramic faces for positive seal
Thermal overload protection with automatic reset
CSA ListedBasin: 18 x 30 structural
foam construction 30-gallon capacity 4 plastic slip type
or cast iron inlet hub
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
24
20
16
12
8
4
00 10 20 30 40 50 60 70 80 90
7
6
5
4
3
2
1
40 80 120 160 200 240 280 320 360
SRM4 4/10 HP
Sealed Cover: 18 solid structural foam
cover with 2 discharge flange, vent flange suitable for 2 or 3 vent, or split steel with 2 or 3 vent
Check Valve: 2 full swingFully Assembled: Includes discharge pipe
inside basin Available in IAPMO
approved models
Pump Only
PAGE 40
-
SEWAGE PUMPS
CMV18301/2 HP Packaged Sewage Ejector System
sPeCIFICAtIonssPeCIFICAtIons
Applications residential septic tank, sewage and large sumps
Capacities 95 GPM 360 LPM
Shut-off head 18 shut-off: 19 shut-off:
5.5 m 5.8 m
Solids handling 2 50.8 mm
Liquids handling raw sewage, effluent and drain water
Intermittent liquid temp up to 140F up to 60CMotor electrical data 1/2 HP, PSC, 1625 RPM, 115V,
12A, 1, 60HzAcceptable pH range 6-9
Discharge, NPT 2 50.8 mm
sPeCIFICAtIons
M9037sse
FeAtUres
Complete package for versatile applications includes: CMV5A-11 sewage pump
1/2 HP, 115V, 12A, 1, 60Hz
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
Recessed vortex impeller provides minimal radial loading for long bearing life
Wide-angle mercury-free mechanical float switch for maximum drawdown
Recessed vortex impeller operates completely out of volute and provides free flow through passage for solids and liquids
Basin: 18 x 30 structural foam
construction 30-gallon capacity 4 plastic slip type
or cast iron inlet hubSealed Cover: 18 solid structural foam
cover with 2 discharge flange, vent flange suitable for 2 or 3 vent, or split steel with 2 or 3 vent
Check Valve: 2 full swing
Pump Only
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
20
15
10
5
0
6
5
4
3
2
1
0
0 50 100 150 200 250 300 350
0 10 20 30 40 50 60 70 80 90 100
CMV5 1/2 HP
PAGE 41
-
SEWAGE PUMPS
M9161sse
SRM-BP BasinPro 4/10 HP Packaged Sewage System
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage, high-capacity sump, effluent
Capacities 95 GPM 360 LPM
Shut-off head 19 5.8 m
Solids handling 2 50.8 mm
Liquids handling septic effluent and sewage
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 4/10 HP, PSC, 115V, 12A, 1, 60Hz
Acceptable pH range 5-9
Discharge NPT 2 50.8 mm
Housing heavy cast iron
Power cord 20, 16/3, SJTW
Impeller recessed, thermoplastic
Volute case cast iron
Shaft seal type 11A, carbon & ceramic
Basin size 24 x 24 structural foam construction
sPeCIFICAtIons
FeAtUres
Power for versatile applications
Residential septic tank sewage
Large sumps Long-lasting performance Oil-filled motor for
maximum heat dissipation and continuous bearing lubrication
Recessed vortex impeller for free flow of liquids, solids up to 2 diameter
Rotary shaft seal has carbon and ceramic faces for positive seal
Thermal overload protection with automatic reset
Pump is pre-installed in basin, with integral torque stops to ensure stability
Available with alarm, optional
Basin: Stackable design allows
for compact inventory Integral 360 top grip for
easy lifting and handling in tight spaces
24 x 24 structural foam construction; 45-gallon capacity
Shallow 24 deep basin reduces installation time for digging pit
Anti-floatation features include concrete splash lip and unique basin shape to keep the system from floating or becoming un-installed
Concrete-proof cover insert protects the system from damage during rough-in and masonry work
E-Z Switch rod allows removal of float switch without disassembling basin lid, or handling pump or plumbing. Additional clip for secondary float included; float sold separately
Pump Only
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
24
20
16
12
8
4
00 10 20 30 40 50 60 70 80 90
7
6
5
4
3
2
1
40 80 120 160 200 240 280 320 360
SRM4 4/10 HP
PAGE 42
-
SEWAGE PUMPS
CMV-BP BasinPro 1/2 HP Packaged Sewage System
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage, high-capacity sump, effluent
Capacities 95 GPM 360 LPM
Shut-off head 18 shut-off: 19 shut-off:
5.5 m 5.8 m
Solids handling 2 50.8 mm
Liquids handling raw sewage, effluent and drain water
Intermittent liquid temp up to 140F up to 60CMotor electrical data 1/2 HP, PSC, 1625 RPM, 115V,
12A, 1, 60Hz
Acceptable pH range 6-9
Discharge, NPT 2 50.8 mm
Housing cast iron
Power cord 20, 16/3, SJTW
Impeller recessed, thermoplastic
Volute case thermoplastic
Shaft seal type 11A, carbon & ceramic
Basin size 24 x 24 structural foam construction
sPeCIFICAtIons
M9162sse
FeAtUres
Engineered for many years of maintenance-free operation
Wide-angle, mercury-free mechanical float switch for maximum drawdown
Recessed vortex impeller operates completely out of volute and provides free flow through passage for solids and liquids
Durable motor will deliver many years of reliable service
Available with alarm, optional
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
Recessed vortex impeller provides minimal radial loading for long bearing life
Pump is pre-installed in basin, with integral torque stops to ensure stability
Basin: Stackable design allows for
compact inventory Integral 360 top grip for
easy lifting and handling in tight spaces
24 x 24 structural foam construction; 45-gallon capacity
Shallow 24- deep basin reduces installation time for digging pit
Anti-floatation features include concrete splash lip and unique basin shape to keep the system from floating or becoming un-installed
Concrete-proof cover insert protects the system from damage during rough-in and masonry work
E-Z Switch rod allows removal of float switch without disassembling basin lid, or handling pump or plumbing. Additional clip for secondary float included; float sold separately
Pump Only
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
20
15
10
5
0
6
5
4
3
2
1
0
0 50 100 150 200 250 300 350
0 10 20 30 40 50 60 70 80 90 100
CMV5 1/2 HP
PAGE 43
-
SEWAGE PUMPS
M9178sse
MW-BPBasinPro 1/2 HP Packaged Sewage System
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage, high-capacity sump, effluent
Capacities 135 GPM 510 LPM
Shut-off head 27 shut-off 8.23 m
Solids handling 2 50.8 mm
Liquids handling domestic sewage and drain water
Intermittent liquid temp. up to 140F up to 60CMotor electrical data 1/2 HP, 1625 RPM, PSC (1),
oil-filled, 115V, 9A, 1, 60Hz; 230V, 4.5A, 1, 60Hz
Acceptable pH range 5-9
Discharge NPT 2 50.8 mm
Housing cast iron
Power cord 20, 16/3, SJTW
Impeller thermoplastic
Volute case class 30 cast iron
Shaft seal type 6, carbon & ceramic
Basin size 24 x 24 structural foam construction
sPeCIFICAtIons
FeAtUres
Fully assembled; pump is pre-installed in basin, with integral torque stops to ensure stability
Oil-filled motor for maximum heat dissipation and continuous bearing lubrication
Recessed vortex impeller for free flow of liquids, solids up to 2 diameter
Available with alarm, optional
Basin: Stackable design allows
for compact inventory Integral 360 top grip for
easy lifting and handling in tight spaces
24 x 24 structural foam construction; 45-gallon capacity
Shallow 24- deep basin reduces installation time for digging pit
Anti-floatation features include concrete splash lip and unique basin shape to keep the system from floating or becoming un-installed
Concrete-proof cover insert protects the system from
damage during rough-in and masonry work
E-Z Switch rod allows removal of float switch without disassembling basin lid, or handling pump or plumbing. Additional clip for secondary float included; float sold separately
30
25
20
15
10
5
00 20 40 60 80 100 120 140
10
8
6
4
2
0
0 100 200 300 400 500
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
MW50 1/2 HP
Pump Only
PAGE 44
-
SEWAGE PUMPS
MRJ 4/10 HP Ready Jon System
sPeCIFICAtIonssPeCIFICAtIons
Applications basement bathroom
Capacities 95 GPM 360 LPM
Shut-off head 19 5.8 m
Solids handling 2 50.8 mm
Liquids handling septic effluent and sewage
Intermittent liquid temp up to 140F up to 60CMotor electrical data 4/10 HP, shaded pole,
115V, 12A, 1, 60Hz; 230V, 6A, 1, 60Hz
Acceptable pH range 5-9
Discharge, NPT 2 50.8 mm
Housing heavy cast iron
Power cord 10 (20 optional)
Impeller recessed, thermoplastic
Volute case cast iron
Shaft seal type 11A, carbon & ceramic
sPeCIFICAtIons
M9038sse
FeAtUres
Sewage Ejector Pump Up Package Includes: SRM4S-1 (115V) 4/10 HP
sewage pump Myers poly tank 2 check valve/discharge
piping assembly Ideal for basements,
room additions, factories and warehouses
Simple installation Accommodates toilet,
vanity or humidifier Fits almost anywhere Use with nearly any
toilet style
Concrete floor stays intact; no need to destroy flooring since the Ready Jon can be installed freestanding on top of any level surface
Tank and piping can be hidden behind a wall
Pump Only
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
24
20
16
12
8
4
00 10 20 30 40 50 60 70 80 90
7
6
5
4
3
2
1
40 80 120 160 200 240 280 320 360
MRJ - Ready Jon 4/10 HP
PAGE 45
-
GRINDER PUMPS
M9039sse
MRG202 HP Single Seal Grinder Pump for Residential Applications
sPeCIFICAtIonssPeCIFICAtIons
Applications sewage grinding, effluent and wastewater removal
Capacities 45 GPM 170 LPM
Shut-off head 105 32 m
Liquids handling raw sewage
Intermittent liquid temp. up to 140F up to 60CWinding 311F 155CMotor electrical data 2 HP, 3450 RPM, 1 - capacitor
start/run 230V; 60Hz, 15A
Acceptable pH range 6-9
Discharge NPT 1-1/4 31.75 mm
Sump diameter duplex 36 91.4 cm
Motor housing cast iron
Power cord 20
Impeller eng. thermoplastic
Shaft seal (Optional)
carbon & ceramic tungsten carbide
Impeller thermoplastic
Power cord 20
Pump, motor shaft stainless steel (416 SS)
Min. sump diameter Simplex: Duplex:
24 36
61.0 cm 91.4 cm
sPeCIFICAtIons
FeAtUres
The MRG20 Series features a patented cutter mechanism and recessed impeller design to effectively macerate typical sewage solids into fine slurry
Durable motor will deliver many years of reliable service
Oil-filled motor for maximum heat dissipation and constant bearing lubrication
Recessed impeller reduces radial bearing loads and increases bearing life
High-torque capacitor starts single-phase motor for assured starting under heavy load; no external capacitor needed
CAPACITY GALLONS PER MINUTE
TOTA
L H
EAD
IN M
ETER
S
TOTA
L H
EAD
IN F
EET
CAPACITY LITERS PER MINUTE
140
120
100
80
60
40
20
0
45
40
35
30
25
20
15
10
5
0 10 20 30 40 50 60 70 80
50 100 150 200 250 300
MRG20 2 HP
Heavy-duty 2 HP listed, wide-angle float switch
On-winding current and temperature-sensitive overload
The MRG20 is designed for easy maintenance
Shredding ring and grinder impeller are replaceable without dismantling pump or motor (440 Stainless
Steel, 58-60 Rockwell) 300 Series Stainless
Steel fasteners CSA Listed
PAGE 46
-
GRINDER PUMPS
MRG20 Grinder Pump Systems Completely Pre-Engineered, Pre-Packaged, Pre-Assembled* Systems Ready for Installation
sPeCIFICAtIonssPeCIFICAtIons
Applications package designed specifically for use in residential or light commercial sewer applications with long discharge or high static heads
Pump Myers model MRG20; 2 HP, capacities to 42 GPM, shut-off head 105 feet (see page 46 for more detailed specifications)