Spray Dryer Organic Solvent Recovery Unit · spray air tube, sample box, static electricity removal...
Transcript of Spray Dryer Organic Solvent Recovery Unit · spray air tube, sample box, static electricity removal...
www.yamato-usa.com 1REV_201903
Econ
omica
l Sys
tem
Spray Dryer Organic Solvent Recovery Unit Required for organic solvent samples
GAS410
Organic Solvent Recovery Unit
GF300For Spray Drying
GF200For Granulating
GB210BFor Granulating
GF200For Granulating
ADL311SAWith GF300 Glassware set
GB210Without glassware
Vers
atile
Sys
tem
Large
Capa
city S
ystem
Selectable Glassware
Suitable for water soluble samples
DL410
GB210AFor Spray Drying
www.yamato-usa.com REV_201903
Spray DryerADL311SACompact & Economical
Water evapo-ration rate Max.1300mL/h Temp. control
range 40~220°C Sampleflow Max. 26mL/min. Spray nozzle
(selectable)Customer
benefitNozzle for liquidNozzle for gas
Low cost& economical
ADL311SA: For aqueous soluble samples(When organic solvent is used, a GAS410 organic solvent recovery unit is required.)
Easy setup, easy operationSuitable for heat sensitive samples. High heat is not directly applied to dry, fine powderObtain contaminant free fine powder which is not oxidized and contains minimal moistureDirect drying of solution or solution liquid into fine powder. No pre- or post processes such as filtration, separation, or pulverization requiredSafe and explosion free working is guaranteed in combination with GAS410 due to oxygen & pressure controlOrganic solvents are recovered in a closed loop to protect the environment to enable minimized pol-lutionEasy operation with one-touch detachable mecha-nism for drying chamber and cycloneAn arm jack is equipped as standard for easy instal-lation and removal of glassware attachmentsA service outlet (max.2A) and a sample stand are equipped as standard for connecting a magnetic mixer for stirring suspended liquid samplesUnique peristaltic pump, nozzle cooling mechanism, pulse jet mechanism and a nozzle knocker for stable spray dryingADL311SA is highly mobile on wheels, or usable with shorter height as a bench top unit by removing the movable caster
Easily micronize liquid samples with a spray dryer.
Specifications
Control Panel
Example of installation: ADL311SA + GAS410
Model ADL311SASupported samples Water soluble samplesEvaporated water amount Max. 1300mL/hSpraying system Two-way nozzle, Nozzle No. 1A as standard (0.4mm)Temp. adjusting unit setting range 40 to 220°C (inlet temperature), 0 to 98°C (outlet temperature)Temperature adjusting accuracy Inlet temperature±1°CDrying air amount adjusting range 0 to 0.7m3/minSpray air pressure adjusting range 0 to 0.3MPaLiquid sending pump flow rate range 0 to 26 mL/minSpray air line washing function Spraying at the nozzle tip, manual pulse jet systemExternal output Inlet temperature, outlet temperature, temperature outlet (4-20 mA)Temperature adjusting device PID digital temperature adjusting deviceTouch panel Blower, heater, liquid sending pump, pulse jet switch, error display
Control select switch Inlet temperature, outlet temperature control switch(outlet temperature control is conditional)
Temperature sensor K-thermocoupleHeater 2.0kW(at200V) to 2.88kW(at240V)Liquid sending pump Fixed amount peristaltic pump
Spraying air pumpFor water soluble samples air compressor is used (sold separately).For organic solvent samples the integrated compressor in GAS410 is used (no separate air compressor required)
Service outlet For stirrer: AC115V, Max 2ASuction blower Bypass blowerFilter Suction filter, exhaust filterRecovery of solvent Solvent recovery unit GAS410 (sold separately) is usedSpray nozzle cooling mechanism Connector: nipple x 2, O.D.: ø10.5mmSpray air connection diameter Nipple diameter: ø7mmSpray air pressure Bourdon tube: 0.3 MPaExhaust connecting diameter ø50mmSafety function Inlet/outlet temperature overheat, sample feed reverse rotation
mechanism, over current electric leakage breaker, nozzle connection error
External size W580 x D420 x H1125 mmWeight 80kgPower supply (50/60 Hz) rated current AC220V 17A, AC240V 18A switching of terminals necessaryAccessories Silicon tubes (with a stopper) x 3, exhaust duct (with one hose
band) x 1, outlet temperature sensor, spray air tube, sample box, static electricity removal earth, "Teflon" braided tube hose 5m (with two hose bands)
ADL311SA 2
www.yamato-usa.com 3REV_201903
Diagram
Example of implementation (spray dryer ADL311SA)
Repeatability of spray drying test (spray dryer ADL311SA)
Spraying Nozzle型 式
1A (標準)
1
2A
2
3
ノズル No. ◯F 1650◯A 64 ◯F 2050◯A 64 ◯F 2050◯A 70 ◯F 2850◯A 70 ◯F 2850◯A 64
大きさ (∫) A 406 B1270 C1626 A 508 B1270 C1626 A 508 B1270 C1778 A 711 B1270 C1778 A 711 B1270 C1626
A B C
試料
給気
加圧空気
排気
⑥
⑦
⑧
⑨
⑩
⑪
⑫
① ②
③ ④
⑤
Nozzle for liquid(F) Nozzle for gas(A)
For connectingGAS410(ADL311SA only)
Connecting of pressurized air
AIR OUT
Sample
AIR IN
Suction filter
⑪ ⑫ ⑬
⑮
⑩③
④
⑤
②
①
⑥
⑦
⑧
⑨
⑯
⑭
Piping
ADL311SA+GAS410
Two-way nozzle system
ApplicationsFood and medicinal productsPowdered milk, egg yolks, soy sauce, coffee, s tarches, prote ins, hormones, serums, antibiotics, enzymes, fragrances,essences, etc.
Organic chemistryWaxes, dies, cleaning agents, surface acting agents, agricultural chemicals, antiseptic agents, synthesized resins, pigments, etc.
Inorganic chemistryFerr i tes, ceramics, photocopy toners, magnetic tapes materials, photosensitive materials, various industrial chemicals, waste fluid samples, etc.
Product Name Product CodeFine powder recovery cyclone 212780Safety cover 212784Static removal brush set 212788Viton packing for cyclone inlet/outlet(1 set of 2 types) 212781
Teflon packing for cyclone inlet/outlet (1 set of 2 types) 212782
Airfilter + Mist separator + Regulator set 212789 Supply air filter box(for 0.3 micro meter collection) 212790
Air compressor SL100-8
Optional items
ADL311SA
The tip of the nozzle comprises of a nozzle for liquid and a nozzle for gas.
Easy to take apart for cleaning to prevent contamination
Particle sizes may vary on samples used and parameter settings.
Model Nozzle No. Size (µm)
1A(Standard)
(F)1650 A 406B 1270
(A)64 C 1626
1 (F)2050 A 508B 1270
(A)64 C 1626
2A (F)2050 A 508B 1270
(A)70 C 1778
2 (F)2850 A 711B 1270
(A)70 C 1778
3 (F)2850 A 711B 1270
(A)64 C 1626
Sample name Composition(%)
Inlet temp.(°C)
Outlet temp.(°C)
Dry air amount(m3/min)
Spray air pressure(MPa)
Sent amount of sample liquid (g/min)
Sample recovery rate (%)
Dextrin (solution) 10 150 80 0.4 0.1 6.1 66Dextrin (emulsion) 40 150 80 0.4 0.1 5.1 63Oxidized titanium (suspended liquid) 10 150 85 0.42 0.1 5.3 50Soy sauce 50 130 75 0.36 0.1 5.1 60Salt 10 145 85 0.38 0.1 5.3 52
Test No.
Sample name Sample density(%)
Drying conditions Yield(g)
Recovery rate (%)Inlet temp.
(°C)Outlet temp.(°C)
Dry air amount(m3/min)
Spray air pressure (MPa)
Test sample amount (g/min)
Sent amount of sample liquid (g/min)
Test time (min)
1 Coffee solution 5.00 150 75 0.45 0.15 93.1 3.1 30 4.3 92.42 Coffee solution 5.00 150 75 0.45 0.15 93 3.1 30 4 863 Coffee solution 5.00 150 75 0.45 0.15 91.4 2 30 4 87.54 Coffee solution 5.00 150 75 0.45 0.15 84.9 2.8 30 3.7 87.25 Coffee solution 5.00 150 75 0.45 0.15 83.8 2.8 30 3.7 88.3
No. Part name No. Part name(1) Heater (9) Blower(2) Inlet temperature sensor (10) Solenoid valve(3) Distributor (11) 3-way solenoid valve (ADL311SA only)(4) Drying chamber (12) Needle valve(5) Cap (13) Pressure meter(6) Outlet temperature sensor (14) Spray nozzle(7) Cyclone (15) Liquid sending pump(8) Product collecting container (16) Nozzle cooling mechanism connecting port
www.yamato-usa.com 4
Spray Dryer Pulvis Mini SprayGB-210ASupports spray drying of fine powder of 1μm
Evaporated water Max.1300ml/h Temp.
control range 40 to 220°C Sample flow Variable up to 26ml/min. Spray nozzle
(selectable)Nozzle for liquidNozzle for gas
Capable of drying ultra small samples as low as 0.5g of solid content. Can spray dry into fine powder 1μm in size when optional mini cyclone is used.
Model GB-210A Temp. adjusting unit setting range 40 to 220°C (inlet temperature), 0 to 60°C (outlet temperature) Temperature adjusting accuracy Inlet temperature±1°C Spraying system Two-way nozzle, Nozzle No. 1A as standard Drying air amount adjusting range 0 to 0.7m3/min Spray air pressure adjusting range 0 to 0.3MPa Liquid sending pump flow rate range 0 to 26 ml/min Spray air line washing function Spraying at the nozzle tip, manual pulse jet system External output Inlet temperature, outlet temperature, temperature outlet (4-20 mA) Automatic lift Moving up/down of glass chamber automatic lift Temperature adjusting device PID digital temperature adjusting device Touch panel Blower, heater, liquid sending pump, pulse jet switch, error display Control select switch Inlet temperature, output temperature control switch (outlet temp. control is conditional) Temperature sensor K-thermocouple Heater 2.0 kW (at 200V) to 2.88 kW (at 240V) Liquid sending pump Fixed amount peristaltic pump Spraying air pump Spraying air compressor (sold separately) is used. Service outlet For stirrer: AC100V, Max. 2A Suction blower Bypass blower, brushless DC motor Filter Suction filter, exhaust filter Recovery of solvent Solvent recovery unit GAS410 (sold separately) is used. Spray nozzle cooling mechanism Connector: nipple x 2, O.D.:ø10.5 mm Spray air connection diameter Nipple diameter:ø7 mm Exhaust connecting diameter ø50mm Safety function Inlet/outlet temperature overheat, sample feed reverse rotation mechanism,
over current electric leakage breaker, nozzle connection error External size W760 x D420 x H1350 mm Weight 110kg Power supply (50/60Hz) rated current AC220V 17A, AC240V 18A, Switching of terminals necessary Accessories Silicon tube (with a stopper) x 3, tiron tube (with a stopper) x 2
exhaust duct (with one hose band) x 1, outlet temperature sensor,spray air tube, sample box, static electricity removal earth,Teflon braided hose 5m (with two hose bands), a container table
Specifications
Compact spray dryer that can produce powder easily on a laboratory scale. It is capable of variety of applications from preliminary experiments in a pilot plant to drying work in general laboratories.
Samples unstable at high temperatures can be reliably processed into fine powder. The heat is applied instantly and indirectly to the powder itselfPrepared fine powder will not be oxidized, con-tains minimal moisture and is contaminant-freeDirect drying from solution/suspension liquid to fine powder with a reduced risk of contamination. No pre or post processes such as filtration, sepa-ration, or pulverization are requiredProcessing of samples containing organic solvents is made possible by connecting the Solvent Recovery Unit GAS410This unit can also be used as a fluid bed drying granulator by installing a separate mini bed attachment GF200 instead of GF300 spray drying attachmentAn automatic lift is equipped as standard to enable easy installation or removal of glass drying chamber attachmentA service outlet (max. 2A) and a sample stand are equipped as standard for connecting a magnetic mixer for stirring suspended liquid sampleStable spray drying using a unique peristaltic pump, nozzle cooling mechanism, pulse jet mechanism and a nozzle knocker enable stable spray drying
Control Panel
Mini spray attachment GF300Evaporated water amount MAX1300mL/hSample for drying Suspended solution, emulsionUltra hard glass Cyclone, drying chamber, product container
Inlet temperature, outlet temperature, and drying air amount are digitally displayed. Setting is made on the touch panel that allows operation settings, operation status display
as well as error display, and settings of various operation conditions.
GB210A REV_201903
www.yamato-usa.com 5REV_201903
Diagram
Test Sample name Sample Drying conditions Yield Recovery rate No. density Inlet temp. Outlet temp. Dry air amount Spray air pressure Test sample amount Sent amount of sample liquid Test time (g) (%)
(%) (°C) (°C) (m3/min) kPa(kg/cm2) (g) (g/min) (min) 1 Coffee solution 5 150 80 0.45 147(1.5) 198 6.6 30 8.1 81.8 2 Coffee solution 5 150 80 0.45 147(1.5) 198.7 6.6 30 8.1 81.5 3 Coffee solution 5 150 80 0.45 147(1.5) 200.6 6.7 30 8 79.8 4 Coffee solution 5 150 80 0.45 147(1.5) 198.1 6.6 30 8.2 82.8 5 Coffee solution 5 150 80 0.45 147(1.5) 199.3 6.6 30 8.4 84.3
Repeatability of spray drying test
No. Part name(1) Heater(5) Spray nozzle(7) Liquid sending pump(8) Blower, exhaust filter
(10) Solenoid valve(11) 3-way solenoid valve(12) Needle valve(13) Pressure meter(14) Nozzle cooling port(15) Inlet temperature sensor
No. Part name(16) Outlet temperature sensor(17) Blind(18) Suction port, suction filter(19) Nozzle cooling connection port(20) Drying chamber(21) Cap(22) Distributor(23) Cyclone(24) Product collecting container
Connection
⑧
Connection ofpressurized air
The one touch removal system has made the removal and cleaning of the drying chamber, the cyclone, and the product container much easier.
Food and medicinal products: Powdered milk, egg yolks, soy sauce, cof fee, starches, proteins, hormones, serums,antibiotics, enzymes, fragrant materials, essences, etc. Organic chemistry: Waxes, dies, cleaning agents, sur face acting agents, agr icultural chemicals, antiseptic agents, synthesized resins, pigments, etc.Inorganic chemistry: Ferrites, ceramics, photocopy toners, magnetic tape materials, photosensitive materials, various industrial chemicals, waste fluid of samples, etc.
Spraying Nozzle
HandlingApplications
Organic Solvent Recovery Unit GAS410
Product name Product codeFine grain sample collecting cyclone 212780Safety cover 212784Static removal brush set 212788Air filter + Mist separator + Regulator set 212789 Supply air filter box (for 0.3 μm collection) 212791
Optional items
型 式
1A (標準)
1
2A
2
3
ノズル No. ◯F 1650◯A 64 ◯F 2050◯A 64 ◯F 2050◯A 70 ◯F 2850◯A 70 ◯F 2850◯A 64
大きさ (∫) A 406 B1270 C1626 A 508 B1270 C1626 A 508 B1270 C1778 A 711 B1270 C1778 A 711 B1270 C1626
A B C
試料
給気
加圧空気
排気
⑥
⑦
⑧
⑨
⑩
⑪
⑫
① ②
③ ④
⑤
Nozzle for liquid(F) Nozzle for gas(A)
Easy to take apart for cleaning to prevent contamination
Particle sizes may vary on samples used and parameter settings.
Two-way nozzle system
The tip of the nozzle comprises of a nozzle for liquid and a nozzle for gas.
Model Nozzle No. Size (µm)
1A(Standard)
(F)1650 A 406B 1270
(A)64 C 1626
1 (F)2050 A 508B 1270
(A)64 C 1626
2A (F)2050 A 508B 1270
(A)70 C 1778
2 (F)2850 A 711B 1270
(A)70 C 1778
3 (F)2850 A 711B 1270
(A)64 C 1626
GB210A
www.yamato-usa.com 6
Spray Dryer Pulvis Mini BedGB-210BSpray Dryer (For Granulating, Drying, Mixing)
Processing capacity 50g to 300g
Temp. control range 40 to 220°C Sample flow Variable up to 26ml/min Spray nozzle
(selectable)Nozzle for liquidNozzle for gas
Spray dryer capable of granulating and drying wet powder.Designed to granulate powder and dry wet powder using a fluid bed. This is a fluid bed drying granulator used in combination with the basic unit GB210 and Mini-bed attachment GF200.
Conditions such as hot air temperature, air amount, binder liquid flow amount can be set easily with the setting dial on the front of the unitThe chamber is made of ultra hard glass and the user can observe status of the fluid bed or spraying status. Also, the flowage meter, the spraying pressure meter, the chamber inlet/outlet temperature indicator are useful for evaluation of dataThe unit can also be used as a spraying dryer by installing the mini spray attachment GF300 (optional)The unit has an automatic lift as a standard to enable convenient installation or removal of the glass chamber attachment
Model GB-210BTemp. adjusting unit setting range 40 to 220°C (inlet temperature), 0 to 98°C (outlet temperature)Temperature adjusting accuracy Inlet temperature ± 1°CSpraying system Two-way nozzle, Nozzle No. 1A as standardDrying air amount adjusting range 0 to 0.7m3/minSpray air pressure adjusting range 0 to 0.3MPaLiquid sending pump flow rate range 0 to 26mL/minExternal output Inlet temperature, outlet temperature, temperature outlet (4-20 mA)Automatic lift Moving up/down of glass chamber automatic liftTemperature adjusting device PID digital temperature adjusting deviceTouch panel Blower, heater, liquid sending pump, pulse jet switch, error displayControl select switch Inlet temperature, output temperature control switch (outlet temp. control is conditional)Temperature sensor K-thermocoupleHeater 2.0 kW (at 200V) to 2.88 kW (at 240V)Liquid sending pump Fixed amount peristaltic pumpSpraying air pump Spraying air compressor (sold separately) is usedService outlet For stirrer: AC100V, Max. 2ASuction blower Bypass blower, brushless DC motorFilter Suction filter, exhaust filterSpray nozzle cooling mechanism Connector: nipple x 2, O.D.: ø10.5mmSpray air connection diameter Nipple diameter: ø7mmExhaust connecting diameter ø50mmSafety device Inlet/outlet temperature overheat, sample feed reverse rotation mechanism,
over current electric leakage breaker, nozzle connection errorExternal dimensions W760 x D420 x H1350 mmWeight ~110 kgPower supply (50/60Hz) rated current AC220V 17A, AC240V 18A, Switching of terminals necessaryAccessories Silicon tube (with a stopper) x 3, tiron tube (with a stopper) x 2, exhaust duct (with one
hose band) x 1, outlet temperature sensor, spray air tube, sample box, static electricity removal earth, Teflon braided hose 5m (with two hose bands), container table
Specifications
Mini bed attachment GF200Processingcapacity
50 to 300g(It differs depending on whether the unit is of the batch type or specific samples used.)
Flow layer chamber capacity
3L
Spray nozzle Dual fluid nozzle: 1A standardStirring blades Integrated inside the flow layer
chamberFilter Polyester
(Carbon fiber mixed PTFE membrane laminate)
Filter cleaning mechanism
Pulse jet system
Glass parts Ultra hard glassWeight ~13 kg
GB210B
Control PanelInlet temperature, out-let temperature, and drying air amount are digital ly displayed.Setting is made on the touch panel that
allows operation settings, operation status display as well as error display, and settings of various operation conditions.
REV_201903
www.yamato-usa.com 7REV_201903
Diagram
⑩
⑪ ⑫ ⑬
⑭ ⑱
⑲
⑳
⑮
⑯
⑰ ①
②
③④
⑧
⑨
⑤
⑥
Connection ofpressurized warm
air
Use of the one touch removal system has made removal or cleaning of the drying chamber, cyclone or the product container much easier.
Granulation, drying, mixing of powderApplications:Medicines, food, catalyst, die, detergent, ceramics, etc.
The unit accepts sample weight as less as 50 to 300g and is suitable for experiments of expensive samples or those of a labora-tory level.
Spraying Nozzle
HandlingApplications
No. Part name(1) Heater(2) Micro porous plate(3) Flow layer chamber(4) Filter chamber(5) Nozzle(6) Filter(7) Liquid sending pump (8) Blower(9) Interim pipe(10) Solenoid valve
No. Part name(11) 3-way solenoid valve(12) Needle valve(13) Pressure meter(14) Stirring blades(15) Stirring motor(16) Inlet temperature sensor(17) Outlet temperature sensor(18) Blind(19) Suction port, suction filter(20) Nozzle cooling connection port
*The average granule diameter is a geometric average.
Example of implementation
Product name Product codeSafety cover 212784Viton packing for cyclone inlet/outlet (1 set of 2 types) 212781Teflon packing for cyclone inlet/outlet (1 set of 2 types) 212782Air filter + Mist separator + Regulator set 212789Supply air filter box (for 0.3 µm collection) 212791
Optional items
型 式
1A (標準)
1
2A
2
3
ノズル No. ◯F 1650◯A 64 ◯F 2050◯A 64 ◯F 2050◯A 70 ◯F 2850◯A 70 ◯F 2850◯A 64
大きさ (∫) A 406 B1270 C1626 A 508 B1270 C1626 A 508 B1270 C1778 A 711 B1270 C1778 A 711 B1270 C1626
A B C
試料
給気
加圧空気
排気
⑥
⑦
⑧
⑨
⑩
⑪
⑫
① ②
③ ④
⑤
Nozzle for liquid(F) Nozzle for gas(A)
Easy to take apart for cleaning to prevent contamination
GB210B
Two-way nozzle system
The tip of the nozzle comprises of a nozzle for liquid and a nozzle for gas.
Particle sizes may vary on samples used and parameter settings.
Model Nozzle No. Size (µm)
1A(Standard)
(F)1650 A 406B 1270
(A)64 C 1626
1 (F)2050 A 508B 1270
(A)64 C 1626
2A (F)2050 A 508B 1270
(A)70 C 1778
2 (F)2850 A 711B 1270
(A)70 C 1778
3 (F)2850 A 711B 1270
(A)64 C 1626
Sample Binder Test conditions ResultsName Weight
(min)Name Density
(%)Spray amount(min)
Inlet temp.(°C)
Liquid sending rate (g/min)
Spray pressurekPa (kg/cm2)
Spray times(times)
Nozzle height(cm)
Average dia.(µm)
12~115 meshrecovery rate(%)
Silicon 200 PVA 5.0 77 125 15 59 (0.6) 4 27 339 58Oxidized iron 160 PVA 2.5 50 120 15 98 (1.0) 4 21 205 62Ceramics 200 PVA 3.0 106 120 15 78 (0.8) 3 22 404 82Alumina 160 PVA 3.0 60 110 15 59 (0.6) 4 22 311 88Silica 150 CMC 1.0 100 120 15 78 (0.8) 4 22 306 60Lactose 200 Sorbitol 70.0 10 100 14 98 (1.0) 4 25 390 80Black tea essence 250 Guar gum 0.5 24 85 6 59 (0.6) 10 28 333 77Grease containing powder 200 Glucose 30.0 11 85 4 59 (0.6) 7 22 236 82
www.yamato-usa.com 8
Spray DryerDL410Large Capacity / Fine powder: 40 to 100μm
Evaporated water Max. 3000mL/h Temp.
control range 40 to 300°C Sampleflow Variable up to 70ml/min. Spray nozzle
(selectable) OperationTwo-way nozzle Easy operation
This spray dryer can produce fine particles from 40 to 100μm which are considered to be extremely difficult to produce in laboratories. It is useful for preliminary tests for pilot plant or expensive samples, micro capture spray drying research, substitute for general laboratory drying method etc.
DL410 is a larger capacity spray dryer that also does not require the liquid sample or solution to undergo any pre or post-processes such as filtration, separation, or pulverization. The use of organic solvents is fully supported with the attachment of our GAS410 organic solvent recovery unit. Small, expensive and/or heat sensitive samples can be dried quickly and efficiently with this easy to operate system.
Processes samples as small as 0.5 g of solid matterSafe for heat-sensitive samples, such as food or medical productsNo risk of contamination Digital display of inlet/outlet temperature and drying air volumeDetachable drying chamber, cyclone and product vesselFast and easy clean upUniversal power supply and multilingual touch screen controller
The hot air inlet and drying chamber cover automatically move up and down, and since the cyclone and product vessel can easily be removed, cleaning and maintenance after your experiment is easyControl functions are conveniently arranged on the control panel for various conditionsThe temperature recorder, air flow meter, pressure gauge and other measurements allow easy control of experiment conditions
Spray drying of fine powder as small as 100µm with a high recovery rate.
SpecificationsModel DL410
Water evaporation rate Max. approx. 3,000 ml/hTemperature control range 40°C - 300°C at inletTemperature control accuracy ± 1°C at inletDry air flow rate Max. 1.2 m³/minAir spray pressure control range 0 - 600 k Pa (0-6 kg/cm²)Spraying system Two-way nozzle (Dia. of orifice: 0.7mm) Nozzle No.3 standard supplySpray/hot air contact system Downward spray parallel flow systemTemperature controller PID digital temperature controllerTemperature sensor K thermocoupleStainless pipe heater 2kW x 2 at 240VSample liquid feeding pump Quantitative peristaltic pump, flow rate variable up to 70ml/min.Solvent recovering capability (optional) Organic solvent recovery unit GAS410 must be usedSpray line cleaning Needle inside the nozzle to clean the mesh automatically Safety device Self-diagnostic functions (e.g. temperature aberration); Sample feed reversalAir spray pressure gauge Bourdon tube: 600k Pa (6 kg/cm²)External dimensions (W x D x H) 1060 x 880 x 1750 mm or 42 x 35 x 69 inWeight 180 kg or 397 lbsPower source AC 200V - 240V, single-phase 24 AIncluded AccessoriesSample liquid tube Silicone tube - 2 pcsSafety Cover YesStatic removal brush 1pcAir hose 1 pcExhaust Duct 1 pcOptional AccessoriesOrganic Solvent Recovery Unit GAS410Inlet/outlet temperature recorder Factory installedViton/Tiron Feeding Tube Please inquireNozzle 4, 5 (options), 3 standardCompressed air 28 L/min air volume and 8 kgf/cm2 compressed air is requiredType of gas N2 gas (99.99% purity, medical grade) required when using GAS410
Easy operation and maintenance
Dimensions (Unit:mm)
DL410 REV_201903
www.yamato-usa.com 9REV_201903
Diagram
Application
Control Panel
Spraying Nozzle
Equipment
Time
Spraying Nozzle size (μm)
Sample
AIRIN AIR
OUT
Pressurized airSuctionfilter
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑭
⑮
⑯
⑰
①
②
④
⑤
③⑬
(1)Orifice tube (10)Atomizing nozzle(2)Drying air flow meter (11)Atomizing pressure control valve(3)Heater (12)Atomizing pressure gauge(4)Drying chamber (13)Needle knock Solenoid valve(5)Drying chamber lower half (14)Nozzle blower Solenoid valve(6)Cyclone (15)Cool air control valve(7)Product vessel (16)Head elevation control valve(8)Aspirator (17)Air cylinder for head elevation(9)Sample feed pump
Drying time until the liquid droplets are completely evaporated with hot air.
10.0
0.1
1.0
0.0110
液滴径(μ)
完全蒸発時間(sec)
100 1000
100℃
150
200
250
300
Com
plet
e ev
apor
atio
n tim
e(se
c)
Droplet size(μ)
(1) Spray granulationWith the process of granulation and spheronization, powder liquidityis significantly improved and the pressure is uniform. Applications:aluminum, zirconia, ceramics, heavy metals, cemented carbidefields etc.
(2) Micro captureIn spray drying, the combination of core and coating material is asource solution to obtain encapsulated powder.
Applications:Ink for pressure-sensitive paperAdjustment of pharmaceutical products flavouring and lyolysis.Encapsulation of fragrances used in food and hygiene related productsEncapsulation of dyes, fertilizers, oils, adhesives etc.
(3) Spray cooling granulationDifficult to get dry powder, such as wax,oils and fats, fatty acids, etc.
(4) Special applicationsSpray concentrated, spray reaction,powder sizing, etc.
0 50 100μm
Powder generated by DL410
Burn prevention safety cover and the static removal brush are standard equipment.
Multilingual touch screen controller
DL410
型 式
1A (標準)
1
2A
2
3
ノズル No. ◯F 1650◯A 64 ◯F 2050◯A 64 ◯F 2050◯A 70 ◯F 2850◯A 70 ◯F 2850◯A 64
大きさ (∫) A 406 B1270 C1626 A 508 B1270 C1626 A 508 B1270 C1778 A 711 B1270 C1778 A 711 B1270 C1626
A B C
試料
給気
加圧空気
排気
⑥
⑦
⑧
⑨
⑩
⑪
⑫
① ②
③ ④
⑤
Nozzle for liquid(F) Nozzle for gas(A)
Model Nozzle No. Size (µm)
3(Standard)
(F)2850 A 711B 1270
(A)64.5 C 1638
4 (F)60100 A 1530B 2550
(A)120 C 3060
5 (F)100150 A 2550B 3825
(A)130 C 4530
Particle sizes may vary on samples used and parameter settings.
Burn prevention safety cover
Static removal brush
www.yamato-usa.com 10
Organic Solvent Recovery UnitGAS410Highly safe N2 gas sealed circulation system
Inert N2 Gas Sealed System used in conjunction with Spray DryersThe Organic Solvent Recovery Unit is used to prevent external discharge when using an organic solvent. Unit is used with a spray dryer (ADL311SA or GB-210A).
Dehumidifier (Freezer) integrated in GAS410. No extra freezer/dehumidi-fier equipment neededCompressor included, no need for a separate compressor to operate the spray dryer ADL311SA when using organic solvent samplesFlammable or toxic solvents can be processed by combining a N2 gas sealed circulation system and a solvent recovery system (with freezer and capacitor)Explosion safety with closed loop N2 inert gas systemRecovery of solvent to protect the environment and enable minimized pollution.Drying of easily oxidized materials is possibleSupports low temperature drying of materials that easily deform with heatNo freezing risk due to organic solvent with aqueous solution mixtures which could cause damage to the closed loop GAS410 systemSpray drying and recovery of products and solvents are performed with meticulously devised safety measures
Specifications
Circulationflow
Recovery capacity Cost savings0.12 to 0.65m3/min 1,300ml/h or more With integrated freezer
With integrated compressor
Example of installation: ADL311SA + GAS410with movable casters
ADL311SA
GAS410
Model GAS410Solvent recovery system Capacitor + freezerCirculating gas N2 gas (sealed circulation when connected to ADL311SA or GB-210A)Circulating volume flow 0.12 to 0.65m3/minCompressor (for spraying) Linear compressor integratedCirculation blower Roots blowerSolvent recovery container 2L flaskFreezer Air-cooled condensation full-sealed type: 400W R404ASolvent recovery mechanism Capacitor cooling mechanismFilter Cartridge filterInstruments Cooling trap temperature display monitor
Filter differential pressure meter (monitor for clogging of filter)O2 density display monitorBlower wind amount adjusting volume
O2 Sensor Solid electrolyte (Zirconium) limit current typePump For circulation to measure OxygenSafety device O2 density meter, flammable gas alarm, electric leakage breaker, N2 gas forced introduction (when removing nozzles)External dimensions W700 x D950 x H1500 mmWeight ~130 kgPower source (50/60 Hz) rated current AC200 to 240V 5A (15A)Required N2 amount 15 L/h at 0.1 MPaAccessories Set of connection parts, anti-seismic clamps, interface cable, sample gas for gas alarm inspection, 2L flask
GAS410 REV_201903
www.yamato-usa.com 11REV_201903
Sample
Introduction of N2
メクラ
Not used for GA310 only
Control Panel Fields
Diagram
Optional items
No. Part name(1) Capacitor(2) Sensor(3) Ball valve(4) Clamp(5) Recovery flask(6) Filter element(7) Filter case(8) Differential pressure meter(9) Flow meter (for introduction of N2)(10) Compressor(11) Solenoid valve (for N2 control)(12) Flow meter (for measuring O2 density)(13) Filter(14) Pump(15) O2 Sensor(16) Solenoid valve (for exhaust)(17) Blower(18) Solenoid valve (for introduction of N2)(19) Solenoid valve (for air supply)
No. Part name A O ring B Packing C Hose D Spray nozzle E Tube F Aluminum honeycomb G Cap H Pressure meter I Needle valve J 3-way valve K Solenoid valve L Packing
Major control functions and detection function
Closed system (N2 gas sealed circulation type) O2 density control functionFlammable gas detection functionInlet temperature overheat detection functionOutlet temperature overheat detection functionIn case of an abnormality, the alarm sounds and liquid flow stopsOther self diagnostics functions
Detection of temp. sensor disconnection Overheat preventionDetection of absence of spray nozzle
Non-oxide ceramicsPolymer materialSuper conductivity materialsMedicinal productsFood productsMaterial research
ADL311SA + GAS410 + stand with caster wheels
Connection
Rear of GAS410
Product name Product codeFilter element 0.1µ 212785Viton packing for cyclone inlet/outlet (1 set of 2 types) 212781Teflon packing for cyclone inlet/outlet (1 set of 2 types) 212782Dry air flow meter (differential pressure type)* 212786
* The item marked "*" shall be ordered together with the main unit.
GAS410
www.yamato-usa.com 12
Reference Spray Dryer, Model Supporting Organic Solvent
Repeatability of spray drying test (spray dryer ADL311SA)
Example of implementation (Spray dryer ADL311SA)
Example of implementation (Pulvis mini spray GB-210A)
*Average particle diameter of the geometric mean
(Conditions)(Conditions)
(Conditions)
The factors that influence the particle diameter are the binder liquid feed rate and the spray pressure, the former being the most influential. A higher binder amount will result in larger diameter particles.
The granulation process has many operation factors, the reproducibility depends on the skill level of the operation. The flow state of the granules has a significant impact on the test results. By adjusting the amount of hot air consistent flow conditions are achievable.
Particles generated by the pulvis mini bed are usually in the range of 0.1~1.5a, The particle size uniformity is lower than extrusion granulation and compression granulation methods.The granularity consistency may be regulated by test conditions.
Repeatability of granulation test Change of particle diameter350 250 170 115 80 60 42 32 24 16 12 9.2 7 5
メ ッ シュ (mesh)
50
40
30
20
10
100
90
70
80
60
0
(%)(%)
累積重量
▲
0 200100 500 2000 4000(μ)
1000粒子径
▲
(Sun)Raw material(Mon)Binder 2.5n Spray(Tue)Binder 7.5n Spray(Wed)Binder 15n Spray
(Sun)㈪(Mon) ㈫(Tue) ㈬(Wed)
Particle diameter
mesh
Cumulative weight
350 250 170 115 80 60 42 32 24 16 12 9.2 7(mesh)
50
40
30
20
10
0 50 200 500 2000 (μ)1000
(%)
重 量
▲
粒子径 ▲
Repeatability of granulation test
Wei
ght
Mesh #1 #2 #3 #412 and up 5.6 0.8 1.2 1.312~16 0.5 0.9 1 1.216~24 0.6 0.8 1.2 1.424~32 0.7 0.8 0.9 1.132~42 1.6 1.7 1.9 1.842~60 5.9 4.3 4.8 3.560~80 9.6 8.5 8.5 6.680~115 13.2 15.6 13.4 12.8115 and under 66.8 66.6 67 70.6Average particle size* 135.6 135.7 138.3 136.9
Raw material Sintered alumina (average particle size 40) 400gBinder 5% PVA solution (#500) 25gInlet temperature 100°CBinder liquid feed rate 12.4g/minBinder spray times 6 timesBinder spray pressure 78kPa(0.8kg/cm2)Nozzle height 25cm from microporous plate
Raw material Lactose (100 mesh under) 200gBinder 70% Sorbitol solution 7.3gInlet temperature 90°CBinder liquid feed rate 12g/minBinder spray times 7 timesBinder spray pressure 98kPa(1.0kg/cm2)Nozzle height 22.5cm from microporous plate
Raw material Lactose(100 mesh under) 200gBinder 70% Sorbitol solutionInlet temperature 90°CBinder liquid feed rate 12g/minBinder spray pressure 98kPa (1.0kg/cm2)Nozzle height 25cm from microporous plate
Sample name Composition (%)
Inlet temp.(°C)
Outlet temp.(°C)
Dry air amount(m3/min)
Spray air pressurekPa (kg/cm2)
Sent amount of sample liquid (g/min)
Sample recovery rate(%)
Dextrin (solution) 10 150 80 0.4 98 (1.0) 6.1 66Dextrin (emulsion) 40 150 80 0.4 98 (1.0) 5.1 63Oxidized titanium (suspended liquid) 10 150 85 0.42 98 (1.0) 5.3 50Soy sauce 50 130 75 0.36 98 (1.0) 5.1 60Salt 10 145 85 0.38 98 (1.0) 5.3 52
Test No. Sample name
Sample density(%)
Drying conditionsYield(g)
Recovery rate (%)Inlet temp.
(°C)Outlet temp.(°C)
Dry air amount(m3/min)
Spray air pressure kPa(kg/cm2)
Test sample amount (g/min)
Sent amount of sample liquid (g/min)
Test time (min)
1 Coffee solution 5.00 150 75 0.45 147(1.5) 93.1 3.1 30 4.3 92.42 Coffee solution 5.00 150 75 0.45 147(1.5) 93 3.1 30 4 863 Coffee solution 5.00 150 75 0.45 147(1.5) 91.4 2.0 30 4 87.54 Coffee solution 5.00 150 75 0.45 147(1.5) 84.9 2.8 30 3.7 87.25 Coffee solution 5.00 150 75 0.45 147(1.5) 83.8 2.8 30 3.7 88.3
Sample name Sample density Inlet temp.(°C)
Outlet temp.(°C)
Dry air amount(m3/min)
Spray air pressurekPa(kg/cm2)
Sent amount of sample liquid(g/min)
Recovery rate(%)
Dextrin (solution) 20% solution 140 85 0.48 147(1.5) 8.8 66Drug suspension 10% suspension 145 80 0.42 196(2.0) 8.2 82Black tea extract 20%solution 155 100 0.4 147(1.5) 7.8 72Silica gel 20%solution 150 75 0.48 147(1.5) 12.6 70Iron oxide 3%suspension 175 90 0.4 127(1.3) 9.5 75
Spray Dryer Reference REV_201903
www.yamato-usa.com 13REV_201903
Spray Drying and Granulating Systems
Example of implementation (Pulvis mini bed GB-210B)
Binder category and features
Repeatability of spray drying test (Pulvis mini spray GB-210A)
Example of implementation Pulvis mini spray GB-210A, organic solvent recovery unit GAS410
Sample Binder Test conditions ResultsName Weight
(min)Name Concentration
(%)Spray amount(min)
Inlet temp.(°C)
Liquid sending rate (g/min)
Spray pressurekPa (kg/cm2)
Spray times(times)
Nozzle height(cm)
Average dia.(µm)
12~115 meshrecovery rate(%)
Silicon 200 PVA 5.0 77 125 15 59 (0.6) 4 27 339 58Oxidized iron 160 PVA 2.5 50 120 15 98 (1.0) 4 21 205 62Ceramics 200 PVA 3.0 106 120 15 78 (0.8) 3 22 404 82Alumina 160 PVA 3.0 60 110 15 59 (0.6) 4 22 311 88Silica 150 CMC 1.0 100 120 15 78 (0.8) 4 22 306 60Lactose 200 Sorbitol 70.0 10 100 14 98 (1.0) 4 25 390 80Black tea essence 250 Guar gum 0.5 24 85 6 59 (0.6) 10 28 333 77Grease containing powder 200 Glucose 30.0 11 85 4 59 (0.6) 7 22 236 82
Category FeaturesGelatin Gelatin Low density and weak bonding strength. No need to heat.Dextrin While it has excellent disintegrating and formability, the binding strength is weak.Potato starch Good granulation properties and inexpensive. Used in the pharmaceutical and food sector.Arsinic acid soda Suitable as a binder for the high viscosity samples. Used primarily in the food sector.Gum arabic Warm and spray. Need large amount of binder.CMC (Carboxymethyl cellulose) High viscosity at low temperatures. High amount of powder remains.HPC (hydroxypropyl cellulose) Good cohesion and is suitable for hydrophilic material.MC (methyl cellulose) Strong binding strength, is suitable for rough particles.PVA (Polyvinyl alcohol) Excellent in granulation properties but somewhat difficult to disintegrate granulated products.PVP (Polyvinylpyrrolidone) High molecular weight and strong binding strength, is suitable for hydrophobic material.
Test No. Sample name
S a m p l e density(%)
Drying conditionsYield(g)
Recovery rate (%)Inlet temp.
(°C)Outlet temp.(°C)
Dry air amount(m3/min)
Spray air pressure kPa(kg/cm2)
Test sample amount (g/min)
Sent amount of sample liquid (g/min)
Test t ime (min)
1 Coffee solution 5.00 150 80 0.45 147(1.5) 198.0 6.6 30 8.1 81.82 Coffee solution 5.00 150 80 0.45 147(1.5) 198.7 6.6 30 8.1 81.53 Coffee solution 5.00 150 80 0.45 147(1.5) 200.6 6.7 30 8.0 79.84 Coffee solution 5.00 150 80 0.45 147(1.5) 198.1 6.6 30 8.2 82.85 Coffee solution 5.00 150 80 0.45 147(1.5) 199.3 6.6 30 8.4 84.3
SampleSample density(%)
Inlet temp.(°C)
Outlet temp.(°C)
Drying nitrogen(m3/min)
Spray pressure (kg/cm2)
Sent rate of sample liquid (g/min)
Dispersion medium or solution
Results
Powdered Recovery rate (%)
Solution recovery rate (%)
Others
Hydroxypropyl methylcellulose 10 90 55 0.5 1.0 9.9 * G 65.3 92.5 *Chloroform1: Ethanol1Cellulose polymer 5.0 70 47 0.5 1.0 8.3 Methylene chloride G 72.3Polymer 2.0 100 64 0.5 1.0 8.4 * G 77.8 80.7 *Ethanol95: Water5Resin 23.5 80 55 0.5 1.0 4.2 * G 81.9 96.7 *(Methanol4:Water1) DistributedCarbon + resin 5.8 100 70 0.5 1.0 5.3 IPA G 85.1 94.1Polymer + inorganic salt 10.2 140 98 0.5 1.0 3.8 * G 97.6 97.4 *DimethylacetamidePolyvinylpyrrolidone (K30) 10.0 80 55 0.5 1.0 7.7 Ethanol G 79.4 95.0Polyvinyl pyrrolidone + drug 10.0 80 55 0.5 1.0 7.7 Ethanol G 75.9 95.4Botanical extract 3.0 130 71 0.5 1.0 9.1 * G 96.5 91.9 *Ethanol6: Water4Silicon carbide 38.5 150 84 0.5 1.0 12.1 Ethanol G 89.9 99.9 *Use nozzle 3SAluminum nitride 13.2 150 99 0.5 1.0 12.9 Butyl acetate G 92.2 86.7 *Use nozzle 3SNitride ceramic 60.5 120 83 0.5 1.0 11.3 MEK G 74.7 88.7Superconducting material 33.3 80 60 0.5 1.0 15.7 Acetone G 66.6 99.6Drug 3.61 100 68 0.6 1.0 10.0 * Yes 73.6 87.2 *Ethanol+Methylene chlorideDrug 13.2 60 45 0.32 1.25 6.0 * Yes 87.6 94.7 *Methylene chloride+EthanolW-Cu 50.0 100 62 0.5 0.5 20.7 Ethanol Yes 60.3 91.9Metamorphic polystyrene 48.7 140 60 0.45 1.0 22.3 Water Yes 67.6 91.7Polymer 0.5 150 88 0.5 1.0 8.5 * Yes 83.1 97.6 *Methanol3+Water1Organic matter 50.0 150 88 0.4 1.0 8.3 Methanol YesSilica dispersion 10.0 100 88 0.5 1.0 4.8 * Yes 96.2 99.5 *Ethanol+Water(little)
Spray Dryer Reference
www.yamato-usa.com 14
Spray Dryer Recommended AccessoriesAir Compressor & Air Combination
For Spray Dryer ADL311SA, GB-210A, GB-210B, DL-410
For Spray Dryer ADL311SA, GB-210A, GB-210B
Provides a stable source of oil free airNoiseless and oil freeHigh flow, low noise, low vibration and low maintenanceAutomatic control and smooth operation
SpecificationsBrand SMTmaxModel SL100-8 (110V) SL100-8 (220V)Horsepower 2 x 3/4 HPPower 2X 550 WStarting Pressure (Mpa) 0.5Max Pressure (Mpa) 0.8Noise dB(A) 55Speed (r/min.) 1680Capacity (L/min) 220Cu. Ft. Delivered @ 115 PSI 7.8 CFMTank 42 L (11 gal)Dimensions(L x W x H)
84 x 41 x 63 cm33 x 16 x 25 in
Voltage 110V, 50/60Hz, 10A 220V, 50/60Hz, 8AWeight 47 kg (104 lbs)
Product name Product codeAir combination 212789
ComponentsAir Filter [AF] AF20Mist Separator [AFM] AFM20Regulator [AR] AR20
Model AF20+AFM20+AR20Ambient and fluid temperature -5~60°C (with no freezing)Max. operating pressure 145psi (1.0MPa)Min. operating pressure 7.3psi (0.05MPa)Set pressure range 7.3-102psi (0.05-0.7MPa)Nominal filtration rating [AF/AFM] AF: 5µm, AFM: 0.3µm (99.9 filtered particle size)Outlet side oil mist concentration[AFM] Max 1.0mg/m3 (ANR) (≈0.8ppm)*Bowl material [AF/AFM] PolycarbonateBowl guard [AF/AFM] Semi-standard (steel)Weight ~0.39kg
Specifications
Dimension (mm)
To guarantee moisture-free, oil-free and clean air spray dryingElement and bowl in one-piece for easy replacement (AF)Energy saving regulator (AR)Transparent bowl guard provides 360° visibility
*When the compressor oil mist discharge concentration is 30mg/m3 (ANR).Bowl seal and other o-rings are slightly lubricated.
Air Compressor SL100-8
Air Combination 212789
Spray Dryer Recommended Accessories REV_201903