Sportster Bipe 40 Manual
Transcript of Sportster Bipe 40 Manual
-
8/3/2019 Sportster Bipe 40 Manual
1/32
SportsterBipe 40Instruction Manual
Enginesize .35-.45Wingspan 45 1/2"
Length 41 1/2"
Wing Area 716 sq. in.
Weight 5-61 /2Ibs.
Materials Needed to Complete the Sportster:
4 Channel radio Propeller Fuel tankEngine Wheel collars SpinnerFiberglass cloth/resin Wheels CoveringEngine mounting bolts Hinges Instant glue
Pushrods/clevises Wing bolts EPOXY
The Sportster Bipe 40 was designed for sport flying. This biplane design with symmetrical wings pro-vides full aerobatic maneuverability, yet has enough wing area for docile low speed capability.
The parts are machine cut and sanded for accurate fit. Should you notice a difference in size betweenplans and parts, it is usually because paper changes size with moisture.
Different types of glue may be used suchas epoxy, cyanoacrylate(instant glue) and aliphatic resin (whiteglue). Build on a flat surface for straight wings and fuselage.
Please read through this step-by-step instruction manual before you start building so you will have anoverall ideaof the construction steps and to avoid mistakes Use the plan and parts list to identify the var-
-
8/3/2019 Sportster Bipe 40 Manual
2/32
overall ideaof the construction steps and to avoid mistakes Use the plan and parts list to identify the var
BUILDING THE TAIL SECTION
PREPARETHE FINAND RUDDER
Sandtheforwardand rearsectionsof thefin ifneces-sary for a good fit. Working over the plans, glue the fin section
pieces together. Sand both sides of the rudder.
CUT THE HINGE SLOTS IN THE FIN AND RUD-DER; CUT OUT RUDDER FOR JOINER CLEAR-
ANCE
Draw centerlines down the trailing edge of the finand the leading edge of the rudder. Mark and cut the hingeslots.Two hingesare used above the stabilizer.The third hingeshould be just below the stab and above the tail wheel struttab. Cut out part of the rudder leading edge for elevator joiner
wire clearance. Wait to shape the leading edge until the holeis drilled for the tail wheel tiller arm later.
3. GLUE STABPARTSTOGETHER; SANDTHE STABAND ELEVATORS
Check the fit and sand the forward and rer parts ofthestabso they fit togetherwell. Glue themtogether. Sandbothsides of the stab and elevator halves.
-
8/3/2019 Sportster Bipe 40 Manual
3/32
-
8/3/2019 Sportster Bipe 40 Manual
4/32
2. PREPARE THE RIBS
Draw a rib alignment line down the center of eachtop wing rib. Note that the threecenter ribs have2 extra notchesfor the cabane mounting plate. Draw rib alignment centerlinesdown the back of the leading edge and the front of the trailing
edge.
3. ALIGN AND GLUE RIBS, LEADING EDGE ANDTRAILING EDGETO TOP SPAR
Pin the top spar (the wing will be built (upsidedown) over the waxed paper covered plan. Place the ribs onthe spar. Align the ribs at the positions shown on the plans.Make sure that the three center ribs have the cabane notches"up" as shown. Shim up the trailing edges of the ribs with theextra 1/4 x 1/4 x 24 spars, making sure the centerlines you
drew on the ribs are parallel to the building board. When theribs are aligned correctly, and at 90 degrees to the buildingboard, glue the ribs to the spar. Line up the lines on the ribswith the line on the leading edge. Glue the ribs to the leadingedge. Line up the trailing edge line to the rib lines and glue theribs to the trailing edge.
4. GLUE IN SPAR FILLER BRACE, BOTTOM SPARAND SHEAR WEB
Cut out the area between the spar notches on thetwo end center ribs for the 1/4 x 9/16 balsa spar filler brace.Glue in the 1/4 x 9/16 filler brace pieces from the center rib out
-
8/3/2019 Sportster Bipe 40 Manual
5/32
6. ADD THE SHEETING AND CAP STRIPS
Cut the sheeting to fit first then glue in place. Glueon the 1/16 x 2-1/8 x 24 leading edge sheeting, the 1/16 x 7/8x 24 trailingedgesheeting and the 1/16x 3 x 15 centersectionsheeting. Do not glue the sheeting to the cabane holders asyou will cut away this sheeting later. Cut cap strips from 1/16x
3/16 x 36 balsa and glue them in place over the rib edges.
7. ADD 1/4TRI STOCK BRACES
After the glue is dry, turn the wing over and pin itdown to the buildingboard. Use 1/4 x 36 triangle stock and cutpieces to fit along the length of the cabane holders as shownon the plan. Glue this 1/4 tri to the sheeting and to the cabaneholder. Also cut tri stock to fit on either side of the three center
. ribs on topofthecabane holders. Glue these braces inplace.
\
8. ADD THE REST OF THE SHEETING
Glue on the 1/16x 2-1/8 x 24 leading edge sheeting,
the 1/16x 7/8 x 24 trailing edge sheeting and the 1/16x 3 x 15center section sheeting. Glue on the 1/16x 3/16 cap strips.
-
8/3/2019 Sportster Bipe 40 Manual
6/32
BUILDING THE BOTTOM WING
PREPAREWING RIBS
Markall bottomwing ribswith a rib alignmentcenter-line.Also drawcenterlinesdownthe 1/4x 1/2 x 24 leadingedgeand the 1/4 x 1/2 x 24 trailing edge pieces. There is no top orbottom to the bottom wing at this point.
2. GLUE THE RIBS TO THE SPARBuild the right and left wing panelsseparately. Build
the left panel first. Use the extra spar as a shim at the trailingedge as you did with the tio wing. Pin the bottom spar over theplans. Align the ribs to the spar, shim up the trailing edges ofthe ribs and glue the ribs to the spar. Use the 1/4 x 7/8 x 3 winghold down block as a spacer for location of ribs #1 and #2.(Note:These hold downs are the same size as the ones thatglue into the fuselage later.) Do not glue the hold down block
in place yet.
3. ADD LEADING EDGE, TRAILING EDGE, TOPSPAR, HOLD DOWN AND FILLER
Align the above parts first and then glue in place(leading edge, trailing edge and top spar). Use epoxy to gluethe holddown in place. Gluethe balsa 1/4 x 5/8 x 3 filler abovethe hold down and sand the it to the shape of the rib contour
-
8/3/2019 Sportster Bipe 40 Manual
7/32
5. ADDTHE SHEETINGAND FILLERONTHEOTHERSIDE OFTHE WING PANEL
Whenthe glue isdry,turnthewingpanelover, realignit to the board and glue in the balsa filler on the other side ofthe holddown. Sand it to shape.Add the leadingedgesheeting,the trailing edge sheetingandthe center section sheeting.Add
the cap strips. This completes the left wing panel for now. Re-move the panel from the building board when it is dry. Nowbuild the right wing panel by following steps 1 through 5.
INSTALLING THE WING TIPS
1. GLUE THE WING TIPS TO TOP AND BOTTOMWING PANELS
Cut offthe sheeting and spars even with the tip rib.Do not cut offthe leading edge! Glue the wing tips on both thetop and bottom wingslpanels. The tips should be centered onthe tip rib and the leading edge centerline. The wing tips forthe top wing will have to sanded to an angle at the top to fitagainst the leading edge. Cut the tip brace piecesfrom the 114scrap provided (1/4 x 3 x 11-7/8). Add the filler piece at thelower end of the wing tips, top and bottom. Sand this filler toshape later after hinging and installing the ailerons. Sand the
leading edge to the rounded shape shown on the plans. Cutoff the spars and sheeting even with the root rib on the panels.
Cut the inner tip filler from some scrap balsa and add to
the inside ofthe tip. Shape it to match the ailerons andtip filler blocks.
INSTALLING THE CENTERTRAILING EDGE (BOTTOM WING)I. MAKE CENTER SECTlON/TORQUE ROD AS-
SEMBLIES
-
8/3/2019 Sportster Bipe 40 Manual
8/32
JOINING THE BOTTOM WING PANELS
GLUE THE CENTER RIB TO THE LEFT WING
With the wing panels "up", glue the wedge-shaped
balsa center rib to the root end of the left wing panel. Makesure the wider edge of the center rib is down and that theleading edge and trailingedge are centeredon the tapered rib.Use 5 minute epoxy.
PANEL
_
2. SAND THE CENTER RIB TO THE WING PANELCONTOUR
Roughcut the center rib to the wing airfoil, leavingit about 1/8" oversize. Sand the remainder away with a sandingblocksothat the center ribedges are flush with the wingsheetingsurfaces.
3. JOINTHEWING PANELS; ADDTHEWINGPLATES
Join the wing panelsupside down. Line up the lead-
ing and trailing edges of the panels. Use a straight edge tomake sure the leading edge of the wing is straight. Block upthe wing 7/8" at the center and glue the panels together usingslo set epo See the dra ing on the plan Remember the
-
8/3/2019 Sportster Bipe 40 Manual
9/32
PREPARETHE AILERONS
Cut the aileron stock (5/8 x17-1/2tapered stock) to
length and draw a centerline down the leading edge of theailerons. Mark anddrill the torque rod holes. Groovethe aileronfor torque rod clearance. Make right and left ailerons.
2. CUTTHE HINGE SLOTS; FINAL SAND THE AILE-RONS
Mark and cut the hinge slots into the ailerons andthe wing trailing edge. Shape the leading edge of the aileronsto a V. Temporarily install the ailerons with hinges to checkthe fit. Final sand the wing tips to match the aileron contour atneutral. Do not permanently hinge the ailerons until after theyare covered.
BUILDING THE FUSELAGE1. PREPARETHE FUSELAGE SIDES,
Mark the inside of the fuselage sides right andleft. Cut out partof the wing saddle area at the rear as shown
th l
-
8/3/2019 Sportster Bipe 40 Manual
10/32
3. D GLUE THE DOUBLERS TOTHEFUSELAGE SIDES
Using Bulkhead #1 as a spacer, install the 1/8" balsadoublers crossgrain on the inside of the fuselage sides. Cut thedoubler pieces from 1/8 x 3 x 36 balsa first, position and thenglue in place. Use slow set epoxy or thick cyanoacrylate. Thedoubler should extend 1/4"beyond the position of bulkhead #3.
Trim the doublers to the fuselage contour.
Note: Be carefulwhenyou cut the doubler stock as you needto use what is left in the next step.
4. D BUILD THE THREE REAR FORMERS
Make Formers #4,5 and 6 from 1/8 x 1/4 x 36 balsa.Use the plans as a guide and cut the balsa to size. Glue theparts together to make the three formers. Make push rod bracesfrom scrap 1/8 x 3 x 36 left over from the doubler stock in thestep you just did. The widths of the braces are the same asthat of each of the formers. The braces will be installed whenthe pushrods are installed later. STOP! Did you read the 4-cycleengine instructions if you plan to install a 4-cycle?
D MARK BULKHEAD POSITIONS
Mark the positions of bulkheads #2 and #3on thefuselage sides. Alsomarkthepositionof the balsa dash between
#2 and #3. Mark the positions of the cabane blocks now if youwish.
-
8/3/2019 Sportster Bipe 40 Manual
11/32
FITTHE WING TO THE FUSELAGE
Pin the fuselage sides together perfectly lined up.Check the fit to the wing saddlecutout byplacingthe fuse sideson the wing. Custom sand ifnecessary but do not change thewing incidence.
8. SAND FUSELAGE TAIL; GLUE BULKHEADS #2AND #3 TO THE RIGHT FUSELAGE SIDE
Slightly sand the insides of the fuse sides at the tailfor a better glue joint. Pin the right fuse sideto your work surface.Position the bulkheads correctly (the angle is at the bottom)and glue them in place at 90 degrees to the fuse side.
NOTE: The straight edge at the top of the fuselageside iscalled
the Fuselage Reference Lineand will be used later to align thewing and stab to the fuselage.
9. GLUE LEFT FUSELAGE SIDE TO THE BUL-KHEADS
Align the fuselage sidelbulkhead assembly upsidedown over the top view of the plans. Make sure the flat side isresting flat on the b ilding board and that the b lkheads are
-
8/3/2019 Sportster Bipe 40 Manual
12/32
GLUE IN BULKHEAD
Realign the fuselage upside down over the plansand glue the fuse sides to bulkhead # 1 .Make sure the top of
the bulkhead is flat on the building board and that the front ofthe bulkhead is facing forward.
12. ADD 1/4" TRI BRACING
Addthree pieces of 114trianglestock along the backof the firewall. Extend the throttle linkage hole through the tristock.
13. GLUE FORMERS TO DECK BASE
Notch the1/2 balsadeck base atthe cornersto clearthe doubler as shown on the plans. The deck base should buttup to the doubler. Pin the deck base over the plans to yourwork surface. Mark the location of Formers #4, #5 and #6.Check the fit of the formers and glue them to the deck base
-
8/3/2019 Sportster Bipe 40 Manual
13/32
15. GLUE THE FUSELAGE TO THE DECK BASE
Glue the fuselagesides/bulkhead assembly to thedeck base former assembly. Fuselage sides are glued to thesides of the deck baseand the sides of the formers. The deckbaseglues to the rear of bulkhead #3.
DO NOT GLUETHE FUSELAGESIDESTOGETHER ATTHETAIL UNTIL THE NEXTSTEP!
16. GLUE THE HINGE/FUSELAGETAIL;GLUETHE FUSE SIDES TOGETHER ATTHE TAIL
Glue the rudder hinge just below the stab location.Use the rudder hinge slot as a guide to placement. Keepingthe area open where the tail wheel strut mounting tab will
glue later, glue the fuse sides together at the tail.
17. GLUE PUSHROD BRACES TO FORMERS; GLUEPUSHROD HOUSINGSTO BRACES
Using the pushrod housings as guides, glue the
-
8/3/2019 Sportster Bipe 40 Manual
14/32
ADD THE LANDING GEAR BRACES
Gluein the grooved 1/2x 1-5/16x 3-1/2 landinggearblock at the bottom of bulkhead#2.Add the 1/2 triangle stockalong the front of bulkhead #2 and the top of the landing gearblock. Cut the braces from 1/2" x 6 stock. You may solder themain gear now butdo not install until after the model is finished.
Note-
The wider slot (groove) in the landing gear block ispositioned toward the front of the model for main gear place-ment. The brace fits into the smaller slot.
20. GLUE THE CHIN BLOCK TO THE FUSELAGE
With the fuselage still at 90 degrees to the boardand over the plans, align the chin block to the front of the landinggear block andgluethe chin block to the fuselage. (The fuselage
is not shown aligned to the plans in the photo.)
21. ADD THE BALSA BOTTOM SHEETING
Withall pins removed from the inside of the fuselage,cross-grain sheet the bottom rear of the fuselage. Use 3/32 x3 x 24 balsa and cut pieces to fit. Start at the false bulkhead
and work your way back, gluing one piece at a time. Leave thelast section of sheetingout untilthetailwheelbracket is installedlater. When the glue is dry, remove the fuselage from yourbuilding board and sand the bottom sheeting to shape
-
8/3/2019 Sportster Bipe 40 Manual
15/32
23. ADD FORMERS 1AAND 2A
Glue formers 1A and 2A to the tops of bulkheads 1and 2. When the glue is dry sand the tops of these formers toa slight angle so the top block will mate squarely when glued.Trial fit the assembled fuel tank. Carve out a section of former2A for fuel tank clearance ifnecessary. Ifyou leave the tank inpermanently, plug all fuel lines so balsadust does not enter thelines.
24. ADD THE DASH AND FORMERS 3N3B
Pin the hood top in place to determine the height ofthe dash. Put the cockpit floor in position to determine theplacement of the dash on the fuse side. Glue the dash to thefuse sides. Do not glue on the hood top yet. Glueformer 3A/3Bto the fuselage at the rear of the cockpit on top of bulkhead#3.
. 25. GLUE IN THE COCKPIT FLOOR
Glue inthe balsacockpitfloor betweenthe dash and former 3A/3B on the lines you drew earlier.
-
8/3/2019 Sportster Bipe 40 Manual
16/32
27. PREPARE SMALL CABANE BLOCKS
Clearance holes will have to be cut in the smallcabane blocks for cabane wire clearance. Place the blocks onthe cabane wire ends. The blocks should line up with the topofthe fuselage. Clamp the blocks to the fuselage.Do not gluethe blocks yet!
28. ALIGN THE TOPWING TO THE FUSELAGE
Align the Fuselage Reference Line (top side of thefuselage side) parallelto the work surface.The fuselage shouldbe right side up. Place the top wing onto the cabanes. Line upthe top wing to the work surface and the fuselage as shown inthe drawings. Distance A should equal distance A, B shouldequal B and C should equal C. When the top wing is properlyaligned, mark the positions of the cabane brace blocks in thefuselage. Use slow set epoxy and glue the blocks in place. Fillin the areas around the wires in the blocks with epoxy. Glue onthe 1/16 x 112 x 1-112 plywood cabane brace caps. Recheckthe alignment before the glue sets up.
When the glue is dry, fill inthe slots in the cabane wing holdersin the wing with silicone. Put car wax or similar material on thecabane wires and placethe wing backon the cabanes. Removethe excess silicone that may ooze out ofthe slot. This siliconethat you added makes a good seat for the wires and cuts downon vibration. After the wing is covered later, you will attach thetop wing to the cabanes with the aluminum plates and the #2
x 3/8 screws provided.Ttie plates should be flushwith the wingsheeting. Note
-
Make sure you do not disturb the wing align-mentwhen you apply the silicone to the cabane slots. The wires
-
8/3/2019 Sportster Bipe 40 Manual
17/32
31. SANDTHE TOPS OFTHE HOOD SIDE PIECES
top of the formers so the hood top will mate squarely.Sand the tops of the hoodside piecesflush with the
32. GLUE ON THE HOOD TOP; SAND HOOD SIDESAT COCKPIT
Trim the hood top at the cabanes first before youglue it on as it is a little difficult to sand in that area after thehoodtop is glued on. Gluethe hoodtop in place.Trim the hoodsides at the cockpit as shown on the plans.
33. ADDFORMER6A/6B
Pin the stabilizer in place so the stab is aligned withthe back of the fuselage. Mark the position of former 6A/6B.Remove the stab. Glue 6A/6B in place.
-
8/3/2019 Sportster Bipe 40 Manual
18/32
35. ADD FORMERS 4A AND 5A
Locatethe positionsof formers4A and 5Aby placingastraightedgealongthetopstringer.Placeandgluethe formersso they mate with the top stringer and and are centered fromside to side.
36. ADD THE TURTLE DECK STRINGERS
Use the 1/8 x 1/4 x 16 balsa stock and cut stringersto fit. Start by gluing at 6A/6Bfirst, checking with a straightedge first, and then gluing to 5A, 4A and 3A/3B.
37. PREPARE AND GLUE IN THE SIDE NOSEBLOCKS; FINAL SAND THE FUSELAGE FRONT
Groovethe inside of the nose side block (right or leftdepending on your engine) for the throttle linkage clearance.Using 5 minute, glue the nose side blocks in place. Remove
t th hi bl kj i t C d h d th
-
8/3/2019 Sportster Bipe 40 Manual
19/32
39. ADD NOSE FILLER BLOCK AND SPINNER RING
Usingyour engine as a guide, locatethe placementof the 2-1/4 x 2-1/4 x 1/2 nose filler block. The engine thrustwasher should extend 1/16 to 1/8 inches forward of the fillerblock. Cut away areas on the block for engine clearance. The
placement of these parts depends on what brandspinner youwill use. Inspect your spinner backplate and locate the blockaccordingly. When you are sure of the placement, glue the cross-grain nose filler block in place. Sand the front of the nose sothe front ofthe filler block and the front of the nose side piecesare even. Glue the 1/16 plywood spinner ring in place on thefiller block using your engine and spinner backplate as a guidefor placement. The engine shaft should be centered in the holein the spinner ring.
40. ADD 3/8 TRI STOCK TOTHE NOSE; SAND NOSETO SHAPE
.
Remove the engine and add the 3/8 triangle stockalong the bottom sides of the engine compartment and behindthe filler block. Use3/8 x 12 triangle stock for this step. Customfit these pieces so they glue to the firewall and nose filler block.Now sand and carve the nose of the fuselage to the shape ofthe spinner ring.
41. DRILL FUEL LINE HOLES AND A DRAIN HOLE
Drill the holes in former 1A for the fuel lines. Seethe plan for placement. Drill a hole in the bottom of the enginecompartment just in fron of the firewall for fuel drainage.
-
8/3/2019 Sportster Bipe 40 Manual
20/32
43. PREPARE THE FIN FILLER BLOCKS; GLUE ONTHE STAB, FIN AND FIN FILLER BLOCK
Prepare the fin filler blocks by cutting them to pickup the angle of the top stringer.Then sand them to the contourof the stringers. Shaping and sanding is easy if you tack gluescrapsof balsa the thickness of the stab and fin to the fuselage.
Trim the scrap even with the fuse sides and stringer line, thentack glue the blocks in place and razor plane and sand themto shape. When ready, break the blocks loose and remove anddiscard the scrap. Use epoxy and glue the stabilizer to thefuselage. Glue the fin to the stab at 90 degrees to the stab andaligned on the stab centerline. Glue the fin to the stab at 90degrees to the stab and aligned on the stab centerline. Gluethe prepared fin filler blocks in place with 5 minute epoxy. Re-move excess epoxy.
44. ADD DORSAL FIN AND FILLER PIECES
Use scrap balsa and custom make the dorsal finpiece and filler pieces. Glue the dorsal fin to the fin and 1/4"top stringer. Glue the filler pieces between the top stringer andthe next stringer on each sdie of the dorsal fin. These fillerpieces are used to anchor the covering material later.
45. ADD TAIL WHEEL STRUT; FINISH RUDDER
Glue the tail wheel strut in place as shown on theplans. Use 5 minute and clamp the tail until
dry.Add the last
piece of bottom sheeting. Mark and drill the hole for the tailwheel tiller arm in the rudder. Also groove the rudder leadingedge below the hole for the nylon bearing clearance Shape
-
8/3/2019 Sportster Bipe 40 Manual
21/32
2. DRILLANDTAP WING BOLT HOLES IN THE WINGAND FUSE
Withe fuse aligned to the work surface and the wingaligned to the fuse, drill two 11/64 pilot holes through the winghold down plates in the leading edge of the wing and one hold
in the trailing edge of the wing. Drill the rear hole at an angleso the bolt head will rest flat on the trailing edge. Drill thesepilot holes through the hold downs in the fuselage at the sametime you drill through the wing. Remove the wing. Drill and tapthe holes in the fuselage hold downs for1/4-20 bolts.Counter-bore the leading edge holes in the wing so that the bolts willrest flat against the hold downs in the wing.
3. SAND THE WING FAIRINGS TO SHAPE
Prepare to install the wing fairings by drawing lineson the bottom of the wing evenwith the fuselage sides. Cut thefairings to width. Sand to shape by placing sandpaper on thewing and working the fairings back and forth.
4. GLUETHE FAIRINGS INTHE FUSELAGE CONT
PLACE; SANDTHEMTOOUR
Drill holes through the fairings large enough for thewing bolt heads to pass through. Install the wing bolts and gluethe fairings in place with 5 minute epoxy Be careful not to get
-
8/3/2019 Sportster Bipe 40 Manual
22/32
-
8/3/2019 Sportster Bipe 40 Manual
23/32
-
8/3/2019 Sportster Bipe 40 Manual
24/32
18. EXTENDTHE RADIOANTENNA
Run the antenna out of the radio compartmentof the fuselage and attach it to the front of the fin. DO
NOT cut the antenna wire!19. CONNECT ALL LINKAGES (PUSHRODS),
ERATIONAND SET THE THROWS
Attach clevises to the ends of the elevator andrudder pushrods so they are adjustable at the tail. Theother ends may be attachedby "Z" bends or other methodand does not need to be adjustable. Attach a clevis to theend of the throttle cable and attach it to the engine throttle
arm. Attach the other end of the cable to the throttle servowith a connectorof your choice. The servosand linkagesshouldnot interfere witheachother.Setthe control surfacethrows as shown on the plan.
CONTROL SURFACES, CHECK RADIO OP-
20. RANGE CHECK YOUR RADIO SYSTEM;CHECK THE CENTER OF GRAVITY; RE-CHECK ALL ALIGNMENTS
Your model should balanceat the point shownon the plan. Ifit doesnt, movethe battery and/or receiveraround until the model balances at the point shown. Ifadditional balance weight is needed, add lead weights tothe nose ortail to get the proper balance. Range checkyour radio at your flying site as per your manufacturersrecommendations. Recheck your wing and stab align-ments. Makesurethe rudder is90degrees to the fuselage.Check to see that all hardwareis secure and that all equip-ment is in good condition.
21. TRIMTHEMODEL
Makeyour first flights, with the help ofanexperi-enced modeler/flyerifthis is your first model. The modelmayneed some trimchanges or adjustmentsto the controlsurfaces after the first flight. Adjust the control surfacesat the clevises until the model flies correctly.
SPORTSTER BlPE FOUR-CYCLE CONVERSION INSTRUCTIONS
The Sportster Bipe is a natural for 4-cycle experimentation. The unique looks of the Bipe just screams4-Cycle and the lightweight air-frame and symmetrical airfoil means the Sportster design will make the most ofthe 4-cycle fun. Whether you want to just putter around the sky, or loop, roll and snap, the Sportster/4-Cyclecombination is unbeatable!
Four-cycle engines offer many benefits-theirquiet, realistic sound is pleasing to modelers and non-mod-elers alike. Hightorqueallowstheuse of highpitchor largediameterpropellersfor a newstyle of flightcharacteristics.They are also very fuel efficient for economical operation.
On the other side of the coin, 4 cycles are larger and heavier than equivalent power 2-cycles. Thatmeans some special care must be taken to avoid a nose-heavy airplane, such as moving the firewall and radiofarther back than normal. Well help you with that task with these instructions.
-
8/3/2019 Sportster Bipe 40 Manual
25/32
-
8/3/2019 Sportster Bipe 40 Manual
26/32
HAYES AL-60
-
8/3/2019 Sportster Bipe 40 Manual
27/32
-
8/3/2019 Sportster Bipe 40 Manual
28/32
-
8/3/2019 Sportster Bipe 40 Manual
29/32
IF MWNT WIDTH EXCEEDS TH E SPACE AVAILABLE
. .-
Figure 5
GENERAL INFORMATION
Centerofgravity:A nose heavy airplanecan bea problem!Makesure you check the CG locationduring
construction with the radio components installed.You may need to put the radio as far back in the compartmentas possible. This will avoid having to carry tail weight.
Props:Always start with the manufacturers instructions (especially for break in) for prop selection. Read theirinstructions carefully because 4 cycles use entirely different diameter and pitch propellers because they operateat a lower RPM and produce greater torque than equivalent displacement 2-cycles.
You may find that after operating your sportster with recommendedpropsthat youll want to experimentwith other props. It is amazing how much you can change flight characteristics of a model by changing props.
Ifyou are looking for higher flight speeds from your Bipe than you are getting from the average recom-
mended prop, consider reducing the diameter and/or blade area slightly and increasingthe prop pitch to bring theRPMbackto the normalrange. For example,with our Enya .46 equippedSportsterBipe, the instructions recommend13 x 5, 12x 6, 11 x 7, 11 x 6, 10 x 6, 10x 7 or 10 x 8 props.We started with an 11 x 7 propeller which gave us fairperformance. Larger props will provide slower speeds...fine for big biplanes...but not what we wanted from ourracy Sportster. For faster speed, we found that a 10-1/2 x 7-1/2 propeller added approximately 10 mph to thestraight and level flight which help make vertical maneuvers crisper due to a faster entry speed. There is a tradeoff, however, as the engine idle was somewhat higher due to the lower mass of the wood 10-1/2 x 7-1/2 propeller.Four-cycles like flywheel weight from large diameter props. This made the plane land a little faster than with the11 x 6. The prop we used was a prop designed for .60 size pattern engines, a Max Daily (Radio South) propeller.
A similar prop is also available from DW Products. Their addresses are: .
Radio South DW Products
-
8/3/2019 Sportster Bipe 40 Manual
30/32
PARTNUMBER QTY DESCRIPTIONBALO19 3 BalsaTriangle1/4x36
BAL047BAL053BAL072
BAL073BAL084CANPY017MM40USB4OFO1SB4OFO2SB4OFO3SB40F04SB4OFO5SB40F10SB4OF30
SB40F35SB40F36SB4OPO1SB40P02SS4OWO7SB4OWO8SB40W10SB40W11SB40W17SB4OW18
SB4OW19
SS4OFO7SS4OFO9SS4OF29SS40R01SS40R02SS40R03SS40SO1SS40S02SS40S03SS40W09
RIBS010
15
5
111
121
11
1142111
121
11
1
1
SPORTSTER BlPE 40 PARTS LIST
Balsa1/8x1/4x36Balsa1/16x3x30Balsa1/8x3x36
Balsa1/16 x 3/16 x 36Balsa 3/32 x 3 x 24CanopyMotor MountBalsa1/8 Fuselage SideBalsa 1/8 DeckBasePlywood 1/4 Bulkhead #1Plywood114Bulkhead#2Balsa1/4x 3 x 3-11/16 Bulkhead#3Balsa 1/2 Side BlockBalsa1/8x 3 x 4-1/2 Cockpit Floor
BalsaTriangle112x 6Balsa5/8Chin BlockPlansInstruction BookBalsa FrontBalsa 3/16 x 3-3/4x3-3/4 Wing Fairing RearBalsa3/16WingTipBalsa 5/8 Center TrailingEdgeBalsaTapered318Center Trailing EdgeBalsa 114x 3 x 11-7/8Wing Tip FillerBalsa1/4x9/16x9-7/8 SparFiller
Balsa 3/8 x3-1/2x 11 HoodTopBalsa 114x 1-3/8x 17-112 HoodSide
BalsaTriangle318x 12Balsa114Fin FrontBalsa114Fin RearBalsa1/4RudderBalsa114StabilizerFrontBalsa1/4Stabilizer RearBalsa 114ElevatorBalsaTaperedCenter Rib
Sub Pack-Upper WingRibSet
RIB0047 3 Balsa3/32 NotchedRibs
PARTNUMBER QTY DESCRIPTION
SS4OF22 1 Balsa1/8 Former4ASS4OF23 1 Balsa1/8 Former 5ASS4OF24 1 Balsa 1/4 Former6ASS4OF25 1 Balsa118Former38
SS4OF26 1 Balsa1/8 Former6BSS4OF28 2 Balsa 5/8 Stailizer
SS40W13 4 Balsa1/4x5/8x3FillerBlock
LeadinaEdgeFiller
SB40MO1
NUTS001NYLON03NYLON09
NYLON10NYLON13SCRW002SCRWOO3SCRWO15SCRW024WBNT002
WBNTOO9
WBNTlOl
WHCLOO4WIREF12SB40M02
1 Sub Pack-iardware5 MetalGearHold
DownStraps4 4-40 Blind Nuts2 Nylon Control Horn2 Nylon Hinges
2 Nylon Aileron Connector3 Nylon 1/4-20 Wing Bolt4 2-56x 5/8 Screw
2 4-40x 1/8 Set Screw18 #2 x 3/8Screw1 Wire 3/32 AileronTorque
RodSet1 Wire3/32TailWheel
Assembly1 Wire ElevatorJoiner
2 3/32Wheel Collar1 WrapWire1 Sub Pack GearICabane
4 4-40x1 Bolt
Wire
PlateMETAL009 2 Metal Cabane Mounting
WBNT080 2 Wire Cabane BraceWBNT081 1 Wire 5/32 Main Gear WBNT082 2 Wire 1/8 CabaneWBNT089 1 Wire 1/8 Main Gear BraceSB40W01 . 1 Sub Pack-Topwing PartsSB40W02 8 Balsa1/4x 1/4x24
Spars/TESB4OWO3 3 Balsa1/4 x 1/2x24 LE
-
8/3/2019 Sportster Bipe 40 Manual
31/32
-
8/3/2019 Sportster Bipe 40 Manual
32/32
GREATPLANES PRODUCT IMPROVEMENT SHEET
INSTRUCTIONS FOR BALANCING YOUR SUPER SPORTSTERThe recommended balance point for the Super Sportsters is
shown on the plan, and is located approximately 29% back from theleadingedge.However,allSportstershavebeen thoroughlytest flownasfarback as 36%,and found tobe completelystablethroughout theentirerange from 29% to 36%.(Thesenumbers represent a percentage of the
total wing chord,as shownin the sketch).Total Wing Chord
BalancePoints
If, whenbalancingyourSuperSportster,youfind it necessarytoadd severalouncesof nose weight tobalanceit at the locationshownonthe plan, it ispreferable tobalance fartheraft, up to 36%(theaft limit),rather than adding a lotof weight. As you balance farther aft,however,the airplane will become more responsive to elevatorcontrol; therefore,you should reduce the maximum elevatorthrowin accordance with thetableof"Recommended Maximum Elevator Throws."Theelevator throwis measured at thewidest part of the elevator,as shown in the sketch.
M e as u re T hr owHere
I
The best way to balance your Super Sportster is to make aBalancing Stand froma square of 1/4" plywood and two 3/8" dowels.Markthe foreand aftlimitsof thebalancerange on the top ofthe wing (on
both sides of the fuselage), and place the airplane upside down on thebalancing stand as shown in the sketch (empty fuel tank). Move the
airplane forwardoraft on the stand until it balanceswith thestablevel.If it balances outside the 29% to 36% range, you must either shift thelocationof radio componentsoradd weight to the nose ortail until it
balanceswithin the range.
Stab must be level
frontof the recommended range, then adjust the linkages toyour elevatorto provide themaximumthrow listed in the29%-30%column in the table
below.Ifitbalancesnearthemiddleof therange, set your elevator for themaximum throw listed in the 33%column. Ifitbalancesnearthe aftlimitof the range, set your elevator for the maximum throw listed in the 36%column.
MEASUERED BACK FROM THE LE OF BOTTOM WNG
WARNING! Ifyou balanceyour SuperSportsteraftof the planlocation but fail to reduce the maximum elevator throw, theelevatormayovercontrolthepitchoftheairplane,and mayresult
in unwantedstallsand "snap rolls"!