SPIRA-TROL 1/2 to 4 ANSI Two-port LEA, LFA and LLA Control...
Transcript of SPIRA-TROL 1/2 to 4 ANSI Two-port LEA, LFA and LLA Control...
Glo
be C
ontr
ol
Valv
es
84
Local regulation may restrict the use of this product below the conditions quoted. Limiting conditions refer to standard connections only.In the interests of development and improvement of the product, we reserve the right to change the specification.
Con
trol
Valv
es
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
TI-P377-01-US 08.11
100
50
0100500
Flow
%
Valve opening %
Fast opening Linear
Equal percentage
DescriptionSPIRA-TROL is a range of two-port single seat globe valves with cage retained seats conforming to ASME/ANSI standards. These valves are available in three body materials in sizes ranging from 1/2" to 4". When used in conjunction with a pneumatic or electric linear actuator they provide characterised modulating or on/off control.
SPIRA-TROL valve characteristic - options:
LEA Equal percentage (E) - Suitable for most modulating process control
applications providing good control at all flowrates. LFA Fast opening (F) - For on/off applications only.
LLA Linear (L) - Primarily for liquid flow control where the differential
pressure across the valve is constant.Important note: Throughout this document, reference has been made to the standard LEA control valve. With the exception of trim type, the LEA, LFA and LLA control valves are identical.
SPIRA-TROL valve options: PTFE seals - StandardStem sealing Bellows / PTFE - Zero emissions Bellows / graphite - Zero emissions + High temperatures Graphite packing - High temperature applications
Metal-to-metal 431 stainless steel - standard
316L stainless steel Seating Soft seating PTFE for tight shut-off Hard facing 316L stainless steel with Stellite 6 facing - for more arduous applicationsBonnet type Standard bonnet Extended bonnet for large pipe lagging or hot / cold applicationsTrim Standard Low noise
SPIRA-TROL two-port valves are compatible with the following actuators and positioners:Electric EL5600, Rotork CVL, Belimo NV and AFPneumatic PN1000 and PN9000 series PP5 (pneumatic) or EP5 (electro-pneumatic)Positioners ISP5 (intrinsically safe electro-pneumatic) SP400/SP500 (microprocessor based electro-pneumatic) SP300 (digital communications)Refer to the relevant Technical Information sheet for further details.
Technical dataPlug design Parabolic Metal-to-metal ANSI Class IVLeakage
Soft seal ANSI Class VIRangeability 50:1 1/2" to 2" 3/4"Travel
2-1/2" to 4" 1-3/16"
Typical flow characteristic curves
Sizes and pipe connectionsType Body material Connections Size range
LEA31 Cast iron Screwed NPT 1/2", 3/4", 1", 1-1/4", 1-1/2" and 2"
LEA33 Cast iron Flanged ANSI 125 1", 1-1/2", 2", 2-1/2", 3" and 4"
LEA43 Carbon steel Flanged ANSI 150 1/2", 3/4", 1", 1-1/2", 2", 2-1/2", 3" and 4"
LEA63 Stainless steel Flanged ANSI 150 1/2", 3/4", 1", 1-1/2", 2", 2-1/2", 3" and 4"
Con
trol
Va
lves
Glo
be C
ontr
ol
Valv
es
85
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222© Spirax Sarco, Inc. 2003
TI-P377-01-US 08.11
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
Type No. Part Material
1 Body Cast iron ASTM A126B
LEA31 2 Bonnet Ductile iron ASTM A359
LEA33 2a Bonnet extension Cast steel ASTM A216 WCB
3 Stem lock-nut Stainless steel
1 Body Cast steel ASTM A216 WCB
2 Bonnet 1/2" to 2" Forged steel ASTM A105N
LEA43 2-1/2" to 4" Cast steel ASTM A216 WCB
2a Bonnet extension Cast steel ASTM A216 WCB
3 Stem lock-nut Stainless steel
1 Body Stainless steel ASTM A351 CF8M
2 Bonnet Stainless steel ASTM A351 CF8M
LEA63 2a Bonnet extension Stainless steel ASTM A351 CF8M
3 Stem lock-nut Stainless steel
4 Bonnet gasket Spiral wound 316L / graphite
5 Seat retaining cage Stainless steel 316L
6 Valve seat ring Stainless steel (See options page 1)
7 Seat gasket Spiral wound 316L / graphite
8 Valve plug and stem Stainless steel (See options page 1)
9* Lower stem guide Nitronic 60
10 Lower stem wiper PTFE
11* Packing guard washer Stainless steel 316L
12* Spring Stainless steel
All 13 Packing spacer Stainless steel 316L
versions 14* Chevron packing set PTFE
using 15* Outer ‘O’ ring Viton
PTFE 16* Upper stem guide Nitronic 60
seals 17* Inner ‘O’ ring Viton
18 Gland nut Stainless steel
19 Scraper ring PTFE
20 Actuator clamp nut Plated carbon steel
21 Bellows assembly Stainless steel AISI 316Ti + 316L
22 Bonnet extension gasket Spiral wound 316L / graphite
23 Top plate (used on bonnet extension only) Stainless steel 316L
24 Lower spindle bearing housing Stainless steel 316L
25 Lower spindle bearing Stellite 6
26 Spindle lock and anti-rotation nut Stainless steel 316L
27 Bonnet nuts
KEA3_ and KEA4_ Steel ASTM A194 Gr. 2H
KEA6 Steel ASTM A194 Gr. 8M KEA3_ and KEA4_ Steel ASTM A193 Gr. B7
28 Bonnet studs
KEA6 Steel ASTM A193 Gr. B8 M2
Graphite packing 9
16 Top and bottom stem guide Stellite 6
High 14 Graphoil packing Graphite rings
temperature 11
packing 12 Not used
15
17
Materials
Glo
be C
ontr
ol
Valv
es
86
Con
trol
Valv
es
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
LEA valvewith bellows seal
LEA valve
TI-P377-01-US 08.11
Con
trol
Va
lves
Glo
be C
ontr
ol
Valv
es
87
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222© Spirax Sarco, Inc. 2003
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
Cast Iron ValvesLEA31 LEA31B LEA33 LEA33B
Carbon Steel ValvesLEA43 LEA43B
Stainless Steel ValvesLEA63 LEA63B
The product must not be used in this region.
Pressure/temperature limits
Tem
per
atur
e °F
Pressure psig
Steam saturation curve
Tem
per
atur
e °F
Pressure psig
PTFEGraphite
PTFEGraphite
Steam saturation curve
Tem
per
atur
e °F
Pressure psig
Steam saturation curve
LEA3_ ANSI 125Body design conditions LEA4_ ANSI 150 LEA6_ ANSI 150Maximum design pressure 200 psi @ 150°FMaximum design temperature 450°F @ 125 psi LEA31 -20°F
Minimum design temperature LEA33 -20°F
LEA43 -20°F LEA63 -58°F Standard PTFE chevron packing 450°F PTFE soft seat (G) 392°F
Maximum operating temperature Graphite packing (H) 450°F
Extended bonnet (E) with PTFE chevron packing 450°F Extended bonnet (E) with graphite packing 450°F Bellows (B) 450°F LEA31 -20°F LEA33 -20°F LEA43 -20°FMinimum operating temperature
LEA63
PTFE Packing -20°F Graphite Packing -58°FMaximum differential pressures: See relevant actuator Technical Information sheetMaximum cold hydraulic test pressure LEA31 300 psig Warning: If the valve is fitted with a LEA33 300 psigbellows it must be removed if hydraulic LEA43 300 psigtesting is to be done. LEA63 300 psig
TI-P377-01-US 08.11
Glo
be C
ontr
ol
Valv
es
88
Con
trol
Valv
es
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
Cv values
Nominal size
Size 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4"
Travel 3/4” 1- 3/16”
Equal % 5.0 7.5 12.0 16.0 30 45 75 120 190
Full port
Linear 5.0 7.5 12.0 16.0 30 45 75 120 190
Fast
opening 5.0 7.5 12.0 16.0 32 50 88 136 210
Standard Reduced trim 1
Equal % 2.5 5.5 8.5 18.0 16 33 48 85 130
trims Linear 2.5 5.5 8.5 12.0 18 33 48 85 130
Reduced trim 2
Equal % 1.8 2.5 6.0 8.5 13 18 36 50 90
Linear 1.8 2.5 6.0 8.5 13 18 36 50 90
Reduced trim 3
Equal % 1.0 1.8 3.0 6.0 9.0 14 18 38 53
Linear 1.0 1.8 3.0 6.0 9.0 14 18 38 53
Micro 0.5 0.5 0.5 - - - - - -
flute 0.2 0.2 0.2 - - - - - -
0.1 0.1 0.1 - - - - - -
Low noise Full port 4.6 7.0 9.3 14.0 23 31.0 64.0 73.0 104.5
trim Reduced trim 1 4.0 5.8 7.0 11.5 15 17.5 40.5 46.5 69.5
Reduced trim 2 3.4 4.6 5.2 8.0 8.5 9.0 34.5 38.0 46.5
TI-P377-01-US 08.11
Con
trol
Va
lves
Glo
be C
ontr
ol
Valv
es
89
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
Dimensions for the SPIRA-TROL (approximate) in inches A A1 B C C1 C2 C3 D E Screwed Flanged Screwed Screwed Flanged Screwed FlangedValve NPT NPT NPT NPT Thread and and and and SW SW SW SW
1/2" 6-1/2" 7-1/4" 1-3/4" 4" 4" 15-1/4" 13-1/4"
3/4" 6-1/2" 7-1/4" 1-3/4" 4" 4" 15-1/4" 13-1/4"
1" 7-3/4" 7-1/4" 2-1/4" 4" 4" 15-3/4" 13-1/4"
1-1/4" 8-1/2" - 2-1/4" 5-3/16" - 16-1/4" - 2-3/4" M8
1-1/2" 9-1/4" 8-3/4" 2-1/2" 5-3/16" 5-3/16" 16-3/4" 14"
2" 10-1/2" 10" 3" 5-3/16" 5-3/16" 17-1/4" 14"
2-1/2" - 10-1/2" - - 7-7/8" - 16-3/8"
3" - 11-3/4" - - 7-7/8" - 16-3/8" 3-3/16" M12
4" - 13-3/4" - - 8-1/2" - 17"
Weights for the SPIRA-TROL (approximate) in lbs LEA31 LEA41 and LEA42 Additional bellows Valve size LEA61 and LEA62 LEA43 LEA63 LEA33 and LEA73 and extended LEA71 bonnet1/2" 16 16 16 16 103/4" 16 18 18 18 101" 22 20 20 20 101-1/4" 25 31 31 29 1211/2" 31 36 36 31 122" 33 38 38 38 122-1/2" - 78 78 84 213" - 86 89 91 21 4" - 124 124 132 28
Screwed and socket weld version Flanged version
Bellows sealed or extended bonnet version
TI-P377-01-US 08.11
Glo
be C
ontr
ol
Valv
es
90
Con
trol
Valv
es
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222
SPIRA-TROL 1/2” to 4” ANSI Two-port LEA, LFA and LLA Control Valves
Dimensions / weights for the PN actuator range (approximate) in ins and lbs
Actuator range F G H J Weight Actuator With handwheel
PN1500 and PN2500 16" 46" - - 121.00 -
PN1600 and PN2600 18- 5/10" 46" - - 154.00 -
PN9100E and variants 10 -7/8" 6-11/16" 2-3/16" 8-7/8" 13.25 + 13.00
PN9100R and variants 10 -7/8" 6-11/16" 5-1/2" 8-7/8" 13.25 + 5.50
PN9200E and variants 11-7/8" 11-7/8" 2-3/16" 8-7/8" 37.50 + 15.75
PN9200R and variants 11-7/8" 11-7/8" 5-1/2" 8-7/8" 37.50 + 8.50
PN9320E and variants 12-7/8" 15-9/16" 2-9/10" 13-3/4" 59.50 + 15.75
PN9320R and variants 12-7/8" 15-9/16" 15-7/8" 13-3/4" 59.50 + 8.50
PN9330E and variants 13 -3/8" 15-9/16" 2-9/16" 13-3/4" 59.50 + 15.75
PN9330R and variants 13-3/8" 15-9/16" 15-7/8" 13-3/4" 59.50 + 8.50
Dimensions / weights for the EL actuator range (approximate) in ins and lbsActuator range F G Weight
EL560_ 7" 18" 10
EL561_ 7" 18" 11
EL562_ 7" 18" 12
EL563_ 7" 20" 15
EL564_ 8-3/4" 22-1/2" 22
EL565_ 8-/4" 31-3/4" 44
EL506_ 6-1/4" 17-1/2" 19
TI-P377-01-US 08.11
Con
trol
Va
lves
Glo
be C
ontr
ol
Valv
es
91
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
Spare parts - SPIRA-TROLThe spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares.
Note: When placing an order for spare parts please specify clearly the full product description as found on the label of the valve body, as this will ensure that the correct spare parts are supplied.
Available spares - LEA, LFA and LLAActuator clamping nut AGasket set B, GStem seal PTFE chevrons Ckits Graphite packing C1 Equal percentage plug and seat D, EPlug stem & seat kit Fast opening plug and seat D1, E Linear plug and seat D2, E
Important Notes1. The trim Cv must be specified at the time of ordering.2. Spares kits do not include gaskets. A gasket kit must be
ordered separately.
How to order sparesAlways order spares by using the description given in the column headed ‘Available spares’, and state the size and type of valve including the full product description of the product.
Example: 1 - PTFE stem seal kit for a Spirax Sarco 1" SPIRA-TROL two-port LEA31 PTSUSS.2 Cvs 12 control valve.
How to fit sparesFull fitting instructions are given in the Installation and Maintenance Instructions supplied with the spare.
TI-P377-01-US 08.11
Glo
be C
ontr
ol
Valv
es
92
Con
trol
Valv
es
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
Spare parts - SPIRA-TROL with bellows sealThe spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares.
Note: When placing an order for spare parts please specify clearly the full product description as found on the label of the valve body, as this will ensure that the correct spare parts are supplied.
Available spares - LEA_B, LFA_B and LLA_BActuator clamping nut AGasket set B, GStem seal PTFE chevrons Ckits Graphite packing C1 Equal percentage plug and seat D3, EPlug stem & seat kit Fast opening plug and seat D4, E Linear plug and seat D5, EBellow seat assembly F
Important Notes1. The trim Cv must be specified at the time of ordering.2. Spares kits do not include gaskets. A gasket kit must be
ordered separately.
How to order sparesAlways order spares by using the description given in the column headed ‘Available spares’, and state the size and type of valve including the full product description of the product.
Example: 1 - PTFE stem seal kit for a Spirax Sarco 1" SPIRA-TROL two-port LEA31B TSUSS.2 Cv 12 control valve.
How to fit sparesFull fitting instructions are given in the Installation and Maintenance Instructions supplied with the spare.
TI-P377-01-US 08.11
Con
trol
Va
lves
Glo
be C
ontr
ol
Valv
es
93
Spirax Sarco, Inc., 1150 Northpoint Blvd., Blythewood, SC 29016 • Phone: (803) 714-2000 • Fax: (803) 714-2222
SPIRA-TROL 1/2" to 4" ANSI Two-port LEA, LFA and LLA Control Valves
SPIRA-TROL selection guide:Valve size 1/2", 3/4", 1", 1-1/4", 1-1/2", 2", 2-1/2", 3" and 4"
Valve series L = L series 2-port control valve
E = Equal percentage
Valve characteristic F = Fast opening
L = Linear
Design code A = ANSI
3 = Cast iron
Body material 4 = Carbon steel
6 = Stainless steel
1 = Screwed (NPT)
Connections 3 = Flanged
P = PTFE
Stem sealing B = Bellows / PTFE seals
C = Bellows / Graphite seals
H = Graphite
T = AISI 431 stainless steel
Seating G = PTFE soft seat
S = 316L stainless steel
W = 316L with stellite 6 facing
Type of trim S = Standard
P = Low noise
Trim balancing U = Unbalanced
Bonnet type S = Standard
Bolting S = Standard
Series 2 = .2
Cv To be specified
Connection type To be specified
Selection example:
1" - L E A 4 3 P T S U S S .2 - Cv 10 - Flanged ANSI 150
How to order
Example: 1 off Spirax Sarco 1" SPIRA-TROL LEA43PTSUSS.2 Cv 10 two-port control valve having flanged ANSI 150 connections.
1"
L
E
A
4
3
P
T
S
U
S
S
.2
Cv 10
FlangedANSI 150
TI-P377-01-US 08.11