Speedtronic HMI I

download Speedtronic HMI I

of 128

  • date post

    08-Nov-2014
  • Category

    Documents

  • view

    230
  • download

    8

Embed Size (px)

Transcript of Speedtronic HMI I

g

GEH-6126A Volume I (1 of 2)(Supersedes GEH-6126)

GE Industrial Systems

For SPEEDTRONIC Turbine Control Operators Guide

Document: Issued:

GEH-6126A Volume I (1 of 2) 2002-02-14

For SPEEDTRONIC Turbine Control Operators Guide

2002 General Electric Company, USA. All rights reserved. Printed in the United States of America. GE provides the following document and the information included therein as is and without warranty of any kind, express or implied, including but not limited to any implied statutory warranty of merchantability or fitness for particular purpose. These instructions do not purport to cover all details or variations in equipment, nor to provide for every possible contingency to be met during installation, operation, and maintenance. The information is supplied for informational purposes only, and GE makes no warranty as to the accuracy of the information included herein. Changes, modifications, and/or improvements to equipment and specifications are made periodically and these changes may or may not be reflected herein. It is understood that GE may make changes, modifications, or improvements to the equipment referenced herein or to the document itself at any time. This document is intended for trained personnel familiar with the GE products referenced herein. GE may have patents or pending patent applications covering subject matter in this document. The furnishing of this document does not provide any license whatsoever to any of these patents. All license inquiries should be directed to the address below. If further information is desired, or if particular problems arise that are not covered sufficiently for the purchasers purpose, the matter should be referred to: GE Industrial Systems Post Sales Service 1501 Roanoke Blvd. Salem, VA 24153-6492 USA Phone: + 1 888 GE4 SERV (888 434 7378, United States) + 1 540 378 3280 (International) Fax: + 1 540 387 8606 (All) (+ indicates the international access code required when calling from outside the USA) This document contains proprietary information of General Electric Company, USA and is furnished to its customer solely to assist that customer in the installation, testing, operation, and/or maintenance of the equipment described. This document shall not be reproduced in whole or in part nor shall its contents be disclosed to any third party without the written approval of GE Industrial Systems.

Document Identification: GEH-6126A Volume I (1 of 2) Technical Writer/Editor: Teresa Davidson Technical Responsibility: Michael Good

ARCNET is a registered trademark of Datapoint Corporation. CIMPLICITY and Genius are registered trademarks of GE Fanuc Automation North America, Inc. Ethernet is a trademark of Xerox Corporation. Excel, Microsoft, NetMeeting, Windows, and Window NT are registered trademarks of Microsoft Corporation. Modbus is a registered trademark of Schneider Automation. Pentium is a registered trademark of Intel Corporation. PI-ProcessBook is a registered trademark of OSI Software Inc. SPEEDTRONIC is a trademark of General Electric Company, USA.

Safety Symbol Legend

Indicates a procedure, condition, or statement that, if not strictly observed, could result in personal injury or death.

Indicates a procedure, condition, or statement that, if not strictly observed, could result in damage to or destruction of equipment.

Indicates a procedure, condition, or statement that should be strictly followed in order to optimize these applications.

Note Indicates an essential or important procedure, condition, or statement.

GEH-6126A, Volume I Operators Guide

Safety Symbol Legend a

To prevent personal injury or equipment damage caused by equipment malfunction, only adequately trained personnel should modify any programmable machine.

The example and setup screens in this manual do not reflect the actual application configurations. Be sure to follow the correct setup procedures for your application.

b Safety Symbol Legend

HMI for SPEEDTRONIC Turbine Control GEH-6126A Volume I

gYour Name

To:

Reader CommentsGeneral Electric Company

GE Industrial Systems Documentation Design, Rm. 291 1501 Roanoke Blvd. Salem, VA 24153-6492 USA Fax: 1-540-387-8651 (GE Internal DC 8-278-8651)

We welcome comments and suggestions to make this publication more useful.Todays Date Job Site GE Requisition No. Your Job Function / How You Use This Publication Publication No. Publication Issue/Revision Date If needed, how can we contact you? Fax No. Phone No. E-mail Address

Your Companys Name and Address

General Rating Contents Organization Technical Accuracy Clarity Completeness Drawings / Figures Tables Referencing Readability Excellent Good Fair Poor Additional Comments _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________ _____________________________________________________________

Specific Suggestions (Corrections, information that could be expanded on, and such.) Page No. Comments

______ ______ ______ ______ ______ ______

__________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________

Other Comments (What you like, what could be added, how to improve, and such.) ________________________________________________

___________________________________________________________________________________________ ___________________________________________________________________________________________ ___________________________________________________________________________________________ ___________________________________________________________________________________________ ___________________________________________________________________________________________ ___________________________________________________________________________________________Overall grade (Compared to publications from other manufacturers of similar products, how do you rate this publication?) Superior Comparable Inferior Do not know Comment ____________________________________________

Detach and fax or mail to the address noted above.

......................................................................... Fold here and close with staple or tape .......................................................................................... ____________________________ ____________________________ ____________________________Place stamp here.

GE Industrial SystemsDocumentation Design, Rm. 291 1501 Roanoke Blvd. Salem, VA 24153-6492 USA

...........................................................................................Fold here first .........................................................................................................

ContentsSafety Symbol Legend Reader Comments Chapter 1 Overview Introduction ..............................................................................................................1-1 HMI Overview..........................................................................................................1-2 Product Features ................................................................................................1-2 HMI Components ..............................................................................................1-3 Graphic Displays ...............................................................................................1-4 Communications................................................................................................1-6 Optional Features ..............................................................................................1-7 Application-Specific Features ...........................................................................1-7 Technical Specifications...........................................................................................1-7 Related Documentation ............................................................................................1-8 How to Use This Document .....................................................................................1-9 Text Conventions ..............................................................................................1-9 How to Get Help.....................................................................................................1-10 Chapter 2 Quick-Start Procedures Introduction ..............................................................................................................2-1 Starting Up HMI.......................................................................................................2-2 Alarm Displays.........................................................................................................2-3 Opening Projects ......................................................................................................2-4 Other Tools........................................................................................