Specifications Lifting Capacities - hsc-crane. · PDF fileSpecifications & Lifting Capacities....

1804 05H.EA274

HYDRAULIC CRAWLER CRANE

SCX700E

2

Variation of The Attachment

VARIATIONSCX700E

Line Speed *

Front / Rear Winch m/min

75

Boom Hoist Winch 62

Swing Speed min-1 (rpm) 3.0Travel Speed * km/h 1.3Gradeability % (Degree) 30 (17)Engine Model ISUZU 6HK1 (Stage II, Tier 2)

Engine Rated Output Power kW/min-1

(ps/rpm)140 / 2000

(190 / 2000)

Note : Speeds marked with "*" may vary depending on load applied.

Crane Specification (Boom Longest Length)

Boom Length m 12 to 54Ground Contact Pressure kPa (kgf/cm²) 79.4 (0.81)

(Boom longest length with 15 t hook)Overall Operating Weight t Approximately 68.2

(Boom longest length with 15 t hook)

3

Boom Length m 12 to 51

Ground Contact Pressure kPa (kgf/cm²)

80.3 (0.82)(Boom longest length + aux. sheave,

15 t + 6.5 t hook attached)

Overall Operating Weight t

Approximately 68.9(Boom longest length + aux. sheave,

15 t + 6.5 t hook attached)

Crane Specification (Boom Longest Length with Aux. Sheave)

VARIATION SCX700E

Boom Length m 27 to 45Crane Jib Length m 9 to 18Boom + Crane Jib Longest Length m 45 + 18

Ground Contact Pressure kPa (kgf/cm²)

81.3 (0.83)(Boom + crane jib longest length, 15 t +

6.5 t hook attached)

Overall Operating Weight t

Approximately 69.8(Boom + crane jib longest length, 15 t +

6.5 t hook attached)

Crane Specification (Boom Longest Length with Crane Jib)

4

Variation of The Attachment 2

Specifications 6

Crane Specifications 7

Dimensions and Specifications ................................................................................................................7

Boom and Crane Jib Configurations ........................................................................................................8

Combination of Boom and Crane Jib (Offset Angle 10° and 30°) ..........................................................9

Working Ranges .......................................................................................................................................10

Main Boom ........................................................................................................................................................ 10

Aux. Sheave .......................................................................................................................................................11

Crane Jib ........................................................................................................................................................... 12

Gross Rated Load Table ..........................................................................................................................15

Main Boom ........................................................................................................................................................ 15

Aux. Sheave ...................................................................................................................................................... 16

Main Boom with Aux. Sheave ............................................................................................................................ 17

Crane Jib ........................................................................................................................................................... 18

Main Boom with Crane Jib ................................................................................................................................ 22

Clamshell Specifications 25

Dimensions and Specifications ..............................................................................................................25

Working Ranges ................................................................................................................................................ 25

Specifications .................................................................................................................................................... 25

Clamshell Bucket ............................................................................................................................................... 25

Gross Rated Load Table .................................................................................................................................... 25

CONTENTSSCX700E

VARIATION

SPECIFICATIONS

5

Weights and Dimensions of Disassembled Units 26

Weights and Dimensions List .................................................................................................................26

Equipment List 29

Standard and Optional Equipment .........................................................................................................29

CONTENTS SCX700E

TECHNICAL DATA

6

Specifications

SPECIFICATIONSSCX700E

Specifications

Model ISUZU 6HK1Type 4-cycle, Water-cooled, Direct injection, Turbo-charged,

Diesel engineDisplacement 7.79 litersRated Output 140 kW / 2,000 min-1 (190 ps / 2,000 rpm)Fuel Tank Capacity 285 litersNotes Engine meets Tier 2 / Stage II of engine exhaust gas

emission regulations in USA, Europe, and Japan. Engine rated horsepower is based on international rating formula that includes engine alternator and without fan.

Engine

Control System

Main actuators are actuated by main hydraulic system controlled with pilot hydraulic system. Safety devices are securely operated by combined various electronic control with hydraulic system. Working speed can be precisely controlled according to control lever stroke depending on work.

Control LeversControl levers are designed and located based on ergonomics. Control lever system is cross operation lever type.

Display Panel Design 7 inches size. Located to check work state easily without disturbing the view of the operator.

Control

Hydraulic Oil Tank Capacity 250 liters

Hydraulic Pump Capacity

Max. 29.4 MPa

P1 230 liters / min for Front, Rear, boom hoist winch,travel and sideframe retract

P2 230 liters / min for Front, Rear and travelP3 131 liters / min for SwingP4 36 liters / min for Pilot control

Hydraulic System

Front and Rear WinchWinch Front RearRope Diameter 22 mm 22 mm

Rope LengthStandard 215 m 135 mWinding Capacity 320 m 320 m

Line Pull Rated 63 kN 63 kNBoom Hoist WinchRope Diameter 16 mmRope Length Incorporated 150 m

Hydraulic motor with multi-disc brakes.

Winch

Constructed with a hydraulic motor with reduction gear and multi-disc brakes and a swing bearing which has inner tooth.

Swing System

Upper Weight

Total Weight 23.0 ton8.6 ton Base Weight 1 piece8.4 ton Insert Weight 1 piece3.0 ton Top Weight 2 pieces

Counter Weight

Welded steel construction.

Carbody Frame

Frame Welded steel box construction and can be retracted for transportation.

Shoe 59 track shoes with triple grousers made of induction-hardened rolled alloy. 810mm width.

Upper Roller 2 pieces each side.Lower Roller 10 pieces each side.

Travel Device

1 peace each side.Hydraulic travel device (Hydrayulic motor and reducer)Travel speed(Gradability : 30%) 1.3 km/h

Crawler Sideframe

7

Dimensions and Specifications

51956170

5780

3380 3500

50401000

1750

12000 to 54000

16003340

810

4790 (3500)3980 (2690)

470

3280

1225

1145

R4065(Rear End Swing Radius)

3285

Crane SpecificationsMax. Lifting Load × Working Radius t × m 70 × 3.7Basic Boom Length m 12Max. Boom Length m 54Max. Crane Jib Length m 9 to 18Max. Boom + Jib Length m 45 + 18

Ground Contact Pressure kPa (kgf/cm²) 75.5 (0.77)(w / Basic Boom, 70 t Hook)

Overall Operating Weight t Approximately 64.8(w / Basic Boom, 70 t Hook)

Hook Weight70 t 800 kg40 t 410 kg15 t 360 kg6.5 t 180 kg

Front / Rear Winch Rope No. of Falls and Lifting Load

Hook Capacity ( t )Maximum Rated Load ( t )

10 Falls 9 Falls 8 Falls 7 Falls 6 Falls 5 Falls 4 Falls 3 Falls 2 Falls 1 Fall70 70 58.5 52 45.5 39 32.5 26 19.5 13 -40 - - - 40 39 32.5 26 19.5 13 -15 - - - - - - - 15 13 -6.5 - - - - - - - - - 6.5

NOTE : Data is expressed in SI units followed by conventional units in ( ).

Crane SpecificationsDimensions and Specifications

SPECIFICATIONS SCX700E

Crane Specifications

8

Boom (2/2)Boom Length

(m) Boom Configurations

36

3 9

3 9

6

6

6

65.42

66

3 9

3

3

3 9

9

95.42

66

6 9 9

6 9 95.42

66

393 9

3 9

6 9

6 95.42

66

3 9

3

3

3 9

6

6

6

65.42

66

9 9 9

9 9 95.42

66

42

3 3 9

3 3 9

6 9

6 95.42

66

3

3

9 9 9

9 9 95.42

66

9

9

96

6

6

6 95.42

66

45

3 9

3 9

96

6

6

6 95.42

66

3 9

3

3

3 9

9

9

9

95.42

66

6 9 9 9

6 9 9 95.42

66

48

3 9

3

3

3 9

6 9

6

6

6 95.42

66

3 9

3 9

6 9 9

6 9 95.42

66

51

3 3 9

3 3 9

6 9 9

6 9 95.42

66

9

9

9 96

6

6

6 9 95.42

66

543 9

3 9

9 96

6

6

6 9 95.42

66

Aux. Sheave Installable Boom LengthBoom Length (m) 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54With Aux. Sheave

( : Attachable : Not Attachable )

Dimensions Not Shown In The Figure

Symbols Boom Length (m)

3 36 69 9

Pendant Rope

Length (m) Rope Diameter (mm) Imprint

3 30 □・△・30・3・C5.42 30 □・△・30・5.42・C

6 30 □・△・30・6・C9 30 □・△・30・9・C

Boom and Crane Jib Configurations

Check the pendant rope with referring to the imprints on the rope end.

Boom (1/2)Boom Length

(m) Boom Configurations

125.42

6 6

153

35.42

66

18

3 3

3 3

6

6

5.42

5.42

6

6

6

6

21

3

3

6

9

6

9

5.42

5.42

6

6

6

6

24

3 3

3 3

6

65.42

66

66

6 65.42

66

3

3

9

95.42

66

27

3

3

3

3

3

3

6 9

6 9

5.42

5.42

6

6

6

6

9

95.42

66

6

6

6

6

303 9

3 9

6

65.42

66

3

3

3

3

6

6

6

65.42

66

9 9

9 95.42

66

33

3 3 9

3 3 9

6

65.42

66

3

3

9 9

9 95.42

66

9

9

6

6

6

65.42

66

Crane SpecificationsBoom and Crane Jib Configurations


9

Jib Pendant Rope

Length (m) Rope Diameter (mm) Imprint

2.85 20 □・△・20・2.85・C8.45 20 □・△・20・8.45・C13.9 20 □・△・20・13.9・C20.8 20 □・△・20・20.8・C

Crane Jib (Offset Angle 10° and 30°)Crane Jib Length (m) Offset Angle Crane Jib Configurations

9

10° 4.54.5

13.920.8

30° 4.54.5

13.9

2.85

20.8

13.5

10°4.54.5

4.5

13.9

20.8 8.45

30°4.54.5

4.5

13.9

2.85

20.8 8.45

18

10°4.54.5

4.54.5

13.9

20.88.45

8.45

30°4.54.5

4.54.5

13.9

2.85

20.88.45

8.45

Dimensions Not Shown In The Figure

Symbols Jib Length (m)

4.5 4.50

Combination of Boom and Crane Jib (Offset Angle 10° and 30°)Boom Length (m) 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54

Jib Length (m

)

9

13.5

18( : Attachable : Not Attachable )

Combination of Boom and Crane Jib (Offset Angle 10° and 30°)

Check the pendant rope with referring to the imprints on the rope end.

Crane SpecificationsCombination of Boom and Crane Jib (Offset Angle 10° and 30°)


10

Working Ranges

Main Boom

1.00 m

1.75

m

5 10 15 20 25 30 35 400 45

5

10

15

20

25

30

35

40

45

50

55

60

30°

37°

42°

80°

15 m

18 m

21 m

24 m

27 m

30 m

33 m

36 m

39 m

42 m

45 m

48 m

51 m

54 m

12 m

4.8

m

4.7

m

5.0

m

Maximum Boom Angle

Minimum Boom Angle

70 t Hook 40 t Hook 15 t Hook

Height A

bove Ground

(m)

Working Radius (m)

Crane SpecificationsWorking Ranges


11



Aux. Sheave

5 10 15 20 25 30 35 400 45

5

10

15

20

25

30

35

40

45

50

55

1.00 m

1.75

m

15 m

18 m

21 m

24 m

27 m

30 m

33 m

36 m

39 m

42 m

45 m

48 m

51 m

12 m

30°

34°

41°

80°

3.5

m

Maximum Boom Angle

Minimum Boom Angle

Height A

bove Ground

(m)

Working Radius (m)

12

Crane Jib

5 10 15 20 25 30 35 400 45

5

10

15

20

25

30

35

40

45

50

55

65

60

1.00 m

1.75

m

27 m

30 m

33 m

36 m

39 m

42 m

45 m

30°

35°36°

41°42°

10°

30°

80°

3.5

m

Minimum Boom Angle

Maximum Boom Angle

9 m Crane Jib Offset Angle 10°


Height A

bove Ground

(m)

Working Radius (m)



13

27 m

30 m

33 m

36 m

39 m

42 m

45 m

1.00 m

1.75

m30°

10°

80°

30°

41°40°

33°32°

47°46°

5 10 15 20 25 30 35 40 500 45

5

10

15

20

25

30

35

40

45

50

55

65

60

3.5

m

Crane Jib



Minimum Boom Angle

Maximum Boom Angle

13.5 m Crane Jib Offset Angle 10°

13.5 m Crane Jib Offset Angle 30°

Height A

bove Ground

(m)

Working Radius (m)

14

27 m

30 m

33 m

36 m

39 m

42 m

45 m

5 10 15 20 25 30 35 40 500 45

5

10

15

20

25

30

35

40

45

50

55

65

60

30°

41°

32°

39°

45°

46°

49°

51°

80°

10°

30°

1.00 m

1.75

m

3.5

m

Crane Jib



Minimum Boom Angle

Maximum Boom Angle



Height A

bove Ground

(m)

Working Radius (m)

15

Crane SpecificationsGross Rated Load Table


Gross Rated Load Table

Main Boom

Unit: tonWorking Boom length (m)

Radius(m) 12 15 18 21 24 27 30 333.7 70.00 3.74.0 65.25 62.10/4.2 4.04.5 58.30 58.15 54.50/4.8 4.55.0 52.45 51.85 51.30 46.40/5.3 5.05.5 45.10 44.65 44.25 43.85 40.20/5.8 5.56.0 39.50 39.15 38.80 38.50 38.20 34.60/6.4 30.90/6.9 6.07.0 31.50 31.25 31.05 30.80 30.60 30.40 30.25 27.30/7.5 7.08.0 26.15 25.95 25.75 25.60 25.40 25.25 25.15 24.95 8.09.0 22.25 22.10 21.90 21.80 21.65 21.50 21.40 21.25 9.010.0 19.35 19.20 19.00 18.90 18.75 18.70 18.60 18.40 10.012.0 16.00/11.6 15.10 14.95 14.85 14.70 14.65 14.55 14.40 12.014.0 12.40 12.25 12.15 12.00 11.95 11.85 11.70 14.016.0 12.20/14.2 10.30 10.20 10.05 10.00 9.90 9.75 16.018.0 9.70 /16.8 8.75 8.60 8.55 8.45 8.30 18.020.0 7.90 /19.4 7.45 7.40 7.30 7.15 20.022.0 6.55 6.50 6.40 6.25 22.024.0 5.75 5.65 5.50 24.026.0 5.60 /24.5 5.05 4.90 26.028.0 4.80 /27.1 4.40 28.030.0 4.00 /29.7 30.0

Unit: tonWorking Boom length (m)

Radius(m) 36 39 42 45 48 51 548.0 24.80 22.40/8.69.0 21.15 21.00 19.50/9.1 18.80/9.710.0 18.35 18.20 18.10 18.00 17.10/10.2 15.00/10.8 13.00/11.312.0 14.35 14.25 14.15 14.05 13.90 13.80 12.9514.0 11.65 11.55 11.45 11.35 11.25 11.10 11.1516.0 9.70 9.60 9.55 9.45 9.35 9.20 9.2018.0 8.25 8.15 8.10 8.00 7.85 7.75 7.7520.0 7.10 7.00 6.95 6.85 6.75 6.60 6.6022.0 6.20 6.10 6.00 5.90 5.80 5.70 5.6524.0 5.45 5.35 5.25 5.15 5.05 4.95 4.9026.0 4.85 4.70 4.65 4.55 4.45 4.30 4.3028.0 4.30 4.20 4.10 4.00 3.90 3.80 3.7530.0 3.85 3.75 3.65 3.55 3.45 3.30 3.2532.0 3.50 3.35 3.25 3.15 3.05 2.85 2.8034.0 3.50 /32.3 3.05 2.90 2.80 2.65 2.50 2.4536.0 2.90 /34.9 2.60 2.45 2.30 2.15 2.1038.0 2.40 /37.5 2.15 2.00 1.85 1.8040.0 1.90 1.75 1.60 1.5042.0 1.90 /40.1 1.50 1.35 1.30 /41.944.0 1.50 /42.7 1.30 /42.1

1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions.2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines

Notes:

which are based on other factor of machine structural strength limitation; the design codes/standards applied to the capacitie areare from "Construction Codes for Mobile Crane" and "Ordinance on Safety of Crane and Similar Equipment" issued by Ministry ofHealth, Labour and Welfare, Japan.

3. Capacities are based on freely suspended loads and make no allowance for such factors as the effect of wind, sudden stop of loads,supporting surface conditions and operating speed. Operator must reduce load ratings to take such conditions into account.

4. Deduction from rated capacities must be made for weight of hook block, hook ball, sling, spreader bar or any suspended gear.5. 23.0ton counter weight is required for all capacities on this chart.

WorkingRadius(m)8.09.010.012.014.016.018.020.022.024.026.028.030.032.0

42.044.0

34.036.038.040.0

10 Parts 9 Parts 8 Parts 7 Parts 6 Parts 5 Parts 4 Parts 3 Parts 2 Parts 1 Part

70t 5 sheaves 0.80 70.0 58.5 52.0 45.5 39.0 32.5 26.0 19.5 13.0 -

40t 3 sheaves 0.41 - - - 40.0 39.0 32.5 26.0 19.5 13.0 -

15t 1 sheave 0.32 - - - - - - - 15.0 13.0 -

6.5t 0.18 - - - - - - - - - 6.5

Hook CapacityHook

Weight (t)Maximum Rated Load (t)

WorkingRadius(m)

16

Aux. Sheave

Unit: tonBoom length (m)

12 15 18 21 24 27 30 334.4 6.50 4.44.5 6.50 4.55.0 6.50 6.50 5.05.5 6.50 6.50 6.50 5.56.0 6.50 6.50 6.50 6.50 /6.1 6.50 /6.6 6.07.0 6.50 6.50 6.50 6.50 6.50 6.50 /7.2 6.50 /7.7 7.08.0 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 /8.3 8.09.0 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 9.010.0 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 10.012.0 6.50 6.50 6.50 6.50 6.50 6.50 6.50 6.50 12.014.0 6.50 /12.6 6.50 6.50 6.50 6.50 6.50 6.50 6.50 14.016.0 6.50 /15.2 6.50 6.50 6.50 6.50 6.50 6.50 16.018.0 6.50 /17.8 6.50 6.50 6.50 6.50 6.50 18.020.0 6.50 6.50 6.50 6.50 6.50 20.022.0 6.50 /20.4 6.50 6.40 6.35 6.20 22.024.0 6.10 /23.0 5.65 5.55 5.45 24.026.0 5.20 /25.6 4.95 4.80 26.028.0 4.40 4.25 28.030.0 4.40 /28.2 3.80 30.032.0 3.70 /30.8 32.0

Unit: tonBoom length (m)

36 39 42 45 48 518.0 6.50 /8.89.0 6.50 6.50 /9.4 6.50 /9.910.0 6.50 6.50 6.50 6.50 /10.5 6.50 /11.0 6.50 /11.612.0 6.50 6.50 6.50 6.50 6.50 6.5014.0 6.50 6.50 6.50 6.50 6.50 6.5016.0 6.50 6.50 6.50 6.50 6.50 6.5018.0 6.50 6.50 6.50 6.50 6.50 6.5020.0 6.50 6.50 6.50 6.50 6.50 6.5022.0 6.15 6.05 5.95 5.85 5.75 5.6524.0 5.35 5.25 5.20 5.10 5.00 4.8526.0 4.75 4.60 4.55 4.45 4.35 4.2028.0 4.20 4.10 4.00 3.90 3.80 3.6530.0 3.75 3.60 3.55 3.40 3.30 3.1532.0 3.35 3.20 3.10 3.00 2.85 2.6534.0 3.10 /33.4 2.85 2.70 2.60 2.45 2.3036.0 2.50 2.40 2.25 2.10 1.9538.0 2.10 1.95 1.80 1.6540.0 2.00 /38.6 1.70 1.55 1.3542.0 1.60 /41.2 1.30 1.30 /40.6

Notes:1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions.2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines




38.040.042.0

30.032.034.036.0

22.024.026.028.0

14.016.018.020.0

8.09.010.012.0

10 Parts 9 Parts 8 Parts 7 Parts 6 Parts 5 Parts 4 Parts 3 Parts 2 Parts 1 Part70t 5 sheaves 0.80 70.0 58.5 52.0 45.5 39.0 32.5 26.0 19.5 13.0 -40t 3 sheaves 0.41 - - - 40.0 39.0 32.5 26.0 19.5 13.0 -15t 1 sheave 0.32 - - - - - - - 15.0 13.0 -6.5t 0.18 - - - - - - - - - 6.5

Hook Capacity HookWeight (t)

Maximum Rated Load (t)

WorkingRadius(m)

WorkingRadius(m)

WorkingRadius(m)

WorkingRadius(m)



17



Main Boom with Aux. Sheave

Unit: ton

12 15 18 21 24 27 30 333.7 69.80 3.74.0 64.85 61.70/4.2 4.04.5 57.90 57.75 54.10/4.8 4.55.0 52.25 51.65 51.05 46.20/5.3 5.05.5 44.90 44.45 44.00 43.60 39.90/5.8 5.56.0 39.30 38.90 38.60 38.30 37.95 34.30/6.4 30.60/6.9 6.07.0 31.30 31.05 30.80 30.60 30.35 30.20 30.00 27.00/7.5 7.08.0 25.95 25.70 25.50 25.35 25.20 25.05 24.90 24.70 8.09.0 22.05 21.85 21.70 21.55 21.40 21.30 21.20 21.00 9.010.0 19.15 18.95 18.80 18.70 18.55 18.45 18.35 18.20 10.012.0 15.80/11.6 14.90 14.75 14.65 14.50 14.40 14.35 14.20 12.014.0 12.20 12.05 11.90 11.80 11.70 11.65 11.50 14.016.0 12.00/14.2 10.10 10.00 9.85 9.75 9.70 9.55 16.018.0 9.50 /16.8 8.55 8.40 8.30 8.25 8.10 18.020.0 7.80 /19.4 7.25 7.20 7.10 6.95 20.022.0 6.35 6.30 6.20 6.05 22.024.0 5.55 5.45 5.30 24.026.0 5.40 /24.5 4.85 4.70 26.028.0 4.60 /27.1 4.15 28.030.0 3.80 /29.7 30.0

Unit: ton

36 39 42 45 48 518.0 24.55 22.10/8.69.0 20.90 20.75 19.50/9.1 18.50/9.710.0 18.10 17.95 17.85 17.70 16.40/10.2 14.40/10.812.0 14.10 14.00 13.90 13.80 13.65 13.5014.0 11.40 11.30 11.20 11.10 11.00 10.8516.0 9.50 9.35 9.30 9.20 9.05 8.9018.0 8.00 7.90 7.80 7.70 7.60 7.4520.0 6.90 6.75 6.70 6.60 6.45 6.3522.0 5.95 5.85 5.75 5.65 5.55 5.4024.0 5.20 5.10 5.00 4.90 4.80 4.6526.0 4.60 4.50 4.40 4.30 4.20 4.0528.0 4.10 3.95 3.85 3.75 3.65 3.4530.0 3.65 3.50 3.40 3.25 3.15 2.9532.0 3.25 3.10 3.00 2.85 2.70 2.5034.0 3.20 /32.3 2.75 2.60 2.45 2.30 2.1536.0 2.60 /34.9 2.25 2.15 2.00 1.8038.0 2.10 /37.5 1.85 1.70 1.5040.0 1.60 1.45 1.30 /39.842.0 1.60 /40.1 1.30 /41.3

Notes:1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions.2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines which are based on other factor of machine structural strength limitation; the design codes/standards applied to the capacitie are are from "Construction Codes for Mobile Crane" and "Ordinance on Safety of Crane and Similar Equipment" issued by Ministry of Health, Labour and Welfare, Japan. 3. Capacities are based on freely suspended loads and make no allowance for such factors as the effect of wind, sudden stop of loads, supporting surface conditions and operating speed. Operator must reduce load ratings to take such conditions into account.4. Deduction from rated capacities must be made for weight of hook block, hook ball, sling, spreader bar or any suspended gear.5. 23.0ton counter weight is required for all capacities on this chart.

8.0

WorkingRadius(m)

WorkingRadius(m)

WorkingRadius(m)

WorkingRadius(m)

9.010.0

12.014.016.018.020.022.024.026.028.030.0

40.042.0

Boom length (m)

Boom length (m)

32.034.036.038.0




18

Crane Jib

Unit tonBoom length (m) 27 Boom length (m)

Jib length (m) 9 13.5 18 Jib length (m)Offset angle (deg) Offset angle (deg)

Radius (m) Radius (m)9.4 6.50 9.410.0 6.50 6.50 /11.0 10.012.0 6.50 6.50 /12.1 6.50 5.90 /12.6 12.014.0 6.50 6.50 6.50 6.50 /15.0 5.70 14.016.0 6.50 6.50 6.50 6.25 5.40 4.30 /17.9 16.018.0 6.50 6.50 6.50 5.85 5.15 4.30 18.020.0 6.50 6.50 6.50 5.50 4.95 4.15 20.022.0 6.45 6.50 6.50 5.20 4.75 4.05 22.024.0 5.70 5.80 5.80 4.95 4.55 3.80 24.026.0 5.05 5.15 5.15 4.70 4.40 3.60 26.028.0 4.50 4.60 4.60 4.50 4.25 3.45 28.030.0 4.05 4.10 4.15 4.30 4.10 3.30 30.032.0 3.65 3.70 3.75 3.85 3.80 3.15 32.034.0 3.50 /33.2 3.40 /33.8 3.40 3.50 3.45 3.05 34.036.0 3.10 3.15 3.15 2.95 36.038.0 2.90 /37.5 2.85 2.90 2.85 38.040.0 2.80 /38.3 2.65 2.70 40.042.0 2.50 /41.7 2.45 42.042.8 2.40 42.8



Radius (m) Radius (m)9.9 6.50 9.910.0 6.50 6.50 /11.5 10.012.0 6.50 6.50 /12.6 6.50 5.90 /13.1 12.014.0 6.50 6.50 6.50 6.50 /15.6 5.80 14.016.0 6.50 6.50 6.50 6.35 5.50 16.018.0 6.50 6.50 6.50 6.00 5.25 4.30 /18.5 18.020.0 6.50 6.50 6.50 5.65 5.05 4.20 20.022.0 6.35 6.50 6.45 5.35 4.85 4.10 22.024.0 5.60 5.75 5.70 5.10 4.65 3.90 24.026.0 4.95 5.10 5.05 4.85 4.50 3.70 26.028.0 4.40 4.50 4.50 4.65 4.35 3.55 28.030.0 3.95 4.05 4.05 4.20 4.15 3.40 30.032.0 3.55 3.60 3.65 3.80 3.70 3.25 32.034.0 3.20 3.25 3.30 3.40 3.35 3.15 34.036.0 2.90 /35.8 2.95 3.00 3.10 3.05 3.00 36.038.0 2.80 /36.4 2.70 2.80 2.80 2.90 38.040.0 2.45 2.50 2.55 2.65 40.042.0 2.40 /40.1 2.30 /40.9 2.30 2.40 42.044.0 2.05 2.15 44.046.0 2.00 /44.3 1.90 /45.4 46.0

Notes:1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions.2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines which are based on other factor of machine structural strength limitation; the design codes/standards applied to the capacitie are are from "Construction Codes for Mobile Crane" and "Ordinance on Safety of Crane and Similar Equipment" issued by Ministry of Health, Labour and Welfare, Japan. 3. Capacities are based on freely suspended loads and make no allowance for such factors as the effect of wind, sudden stop of loads, supporting surface conditions and operating speed. Operator must reduce load ratings to take such conditions into account.4. Deduction from rated capacities must be made for weight of hook block, hook ball, sling, spreader bar or any suspended gear.5. 23.0ton counter weight is required for all capacities on this chart.

10 3010 30 10 30

10 3010 30 10 30






19



Crane Jib



Radius (m) Radius (m)10.5 6.50 10.512.0 6.50 6.50 /13.2 6.50 /12.1 5.90 /13.6 12.014.0 6.50 6.50 6.50 5.85 14.016.0 6.50 6.50 6.50 6.50 /16.1 5.60 16.018.0 6.50 6.50 6.50 6.10 5.35 4.30 /19.0 18.020.0 6.50 6.50 6.50 5.75 5.15 4.20 20.022.0 6.20 6.45 6.35 5.50 4.95 4.10 22.024.0 5.45 5.65 5.55 5.20 4.75 4.00 24.026.0 4.80 4.95 4.95 5.00 4.60 3.80 26.028.0 4.25 4.40 4.40 4.60 4.45 3.60 28.030.0 3.80 3.90 3.90 4.10 4.00 3.45 30.032.0 3.40 3.50 3.50 3.65 3.60 3.35 32.034.0 3.05 3.15 3.15 3.30 3.25 3.20 34.036.0 2.75 2.80 2.85 2.95 2.90 3.10 36.038.0 2.45 2.50 2.55 2.65 2.65 2.80 38.040.0 2.30 /38.4 2.20 /39.0 2.30 2.35 2.35 2.55 40.042.0 2.05 2.10 2.10 2.25 42.044.0 1.90 /42.7 1.90 /43.5 1.90 2.00 44.046.0 1.70 1.75 46.048.0 1.60 /46.9 1.50 48.0



Radius (m) Radius (m)11.0 6.50 11.012.0 6.50 6.50 /13.7 6.50 /12.6 12.014.0 6.50 6.50 6.50 5.90 /14.2 14.016.0 6.50 6.50 6.50 6.50 /16.7 5.65 16.018.0 6.50 6.50 6.50 6.20 5.45 4.30 /19.6 18.020.0 6.50 6.50 6.50 5.90 5.20 4.25 20.022.0 6.15 6.35 6.25 5.60 5.05 4.15 22.024.0 5.35 5.55 5.50 5.35 4.85 4.05 24.026.0 4.75 4.90 4.85 5.10 4.70 3.85 26.028.0 4.20 4.35 4.30 4.55 4.40 3.70 28.030.0 3.70 3.85 3.85 4.05 3.90 3.55 30.032.0 3.30 3.45 3.45 3.60 3.50 3.40 32.034.0 2.95 3.05 3.05 3.25 3.15 3.30 34.036.0 2.65 2.70 2.75 2.90 2.85 3.05 36.038.0 2.35 2.40 2.45 2.60 2.55 2.75 38.040.0 2.05 2.10 2.15 2.30 2.25 2.45 40.042.0 1.80 /41.0 1.80 /41.6 1.90 2.00 2.00 2.15 42.044.0 1.70 1.75 1.80 1.90 44.046.0 1.50 /45.3 1.55 1.55 1.70 46.048.0 1.50 /46.1 1.40 1.45 48.050.0 1.30 /49.2 1.30 /49.9 50.0

10 3010 30 10 30

10 3010 30 10 30

20

Crane Jib

Unit: tonBoom length (m) 39 Boom length (m)


Radius (m) Radius (m)11.6 6.50 11.612.0 6.50 6.50 /13.2 12.014.0 6.50 6.50 /14.3 6.50 5.90 /14.7 14.016.0 6.50 6.50 6.50 6.50 /17.2 5.75 16.018.0 6.50 6.50 6.50 6.30 5.50 18.020.0 6.50 6.50 6.50 6.00 5.30 4.30 /20.1 20.022.0 6.00 6.25 6.15 5.70 5.10 4.15 22.024.0 5.25 5.45 5.40 5.45 4.95 4.05 24.026.0 4.60 4.80 4.75 5.05 4.75 3.95 26.028.0 4.05 4.25 4.20 4.45 4.30 3.80 28.030.0 3.60 3.75 3.70 3.95 3.80 3.65 30.032.0 3.20 3.30 3.30 3.50 3.40 3.50 32.034.0 2.85 2.95 2.95 3.15 3.05 3.30 34.036.0 2.50 2.60 2.60 2.80 2.70 2.95 36.038.0 2.15 2.25 2.30 2.45 2.40 2.65 38.040.0 1.90 1.95 2.00 2.15 2.10 2.35 40.042.0 1.65 1.70 1.75 1.90 1.85 2.05 42.044.0 1.30 /43.6 1.45 1.55 1.65 1.65 1.80 44.046.0 1.30 /44.2 1.35 1.40 1.40 1.55 46.048.0 1.30 /46.7 1.30 /47.3 1.30 /47.5 1.35 48.048.7 1.30 48.7



Radius (m) Radius (m)12.0 6.50 /12.1 6.50 /13.7 12.014.0 6.50 6.50 /14.8 6.50 5.90 /15.3 14.016.0 6.50 6.50 6.50 6.50 /17.7 5.80 16.018.0 6.50 6.50 6.50 6.40 5.60 18.020.0 6.50 6.50 6.50 6.10 5.35 4.30 /20.7 20.022.0 5.95 6.20 6.05 5.80 5.20 4.20 22.024.0 5.15 5.40 5.30 5.55 5.00 4.10 24.026.0 4.50 4.75 4.65 4.95 4.75 4.00 26.028.0 4.00 4.15 4.10 4.40 4.20 3.85 28.030.0 3.50 3.65 3.65 3.90 3.70 3.70 30.032.0 3.10 3.25 3.20 3.45 3.30 3.55 32.034.0 2.70 2.85 2.85 3.05 2.95 3.25 34.036.0 2.35 2.50 2.50 2.70 2.60 2.90 36.038.0 2.05 2.15 2.15 2.35 2.25 2.55 38.040.0 1.75 1.85 1.90 2.05 2.00 2.25 40.042.0 1.50 1.60 1.65 1.80 1.75 1.95 42.044.0 1.30 1.35 1.40 1.55 1.50 1.70 44.046.0 1.30 /44.2 1.30 /44.6 1.30 /45.2 1.30 1.30 1.45 46.048.0 1.30 /46.2 1.30 /46.1 1.30 /47.7 48.0

10 3010 30 10 30

10 3010 30 10 30



21



Crane Jib



Radius (m) Radius (m)12.7 6.50 12.714.0 6.50 6.50 /15.4 6.50 /14.3 5.90 /15.8 14.016.0 6.50 6.50 6.50 5.85 16.018.0 6.50 6.50 6.50 6.50 /18.3 5.65 18.020.0 6.50 6.50 6.50 6.15 5.45 4.30 /21.2 20.022.0 5.80 6.10 5.95 5.90 5.25 4.20 22.024.0 5.05 5.30 5.20 5.55 5.10 4.10 24.026.0 4.40 4.65 4.55 4.90 4.65 4.05 26.028.0 3.85 4.05 4.00 4.30 4.10 3.90 28.030.0 3.40 3.60 3.50 3.80 3.60 3.75 30.032.0 2.95 3.15 3.10 3.35 3.20 3.55 32.034.0 2.55 2.75 2.70 2.95 2.80 3.15 34.036.0 2.20 2.35 2.35 2.60 2.45 2.80 36.038.0 1.90 2.05 2.05 2.25 2.15 2.45 38.040.0 1.65 1.75 1.75 1.95 1.85 2.15 40.042.0 1.40 1.45 1.50 1.65 1.60 1.85 42.044.0 1.30 /42.9 1.30 /43.6 1.30 /43.9 1.40 1.35 1.60 44.046.0 1.30 /45.2 1.30 /44.8 1.35 46.046.7 1.30 46.7

10 3010 30 10 30

22



Radius (m) Radius (m)6.4 33.80 33.60 33.50 33.10 33.10 32.50 6.47.0 29.65 29.45 29.35 28.95 29.00 28.40 7.08.0 24.50 24.30 24.20 23.85 23.85 23.35 8.09.0 20.75 20.55 20.45 20.15 20.10 19.70 9.010.0 17.90 17.75 17.60 17.35 17.25 16.95 10.012.0 13.85 13.75 13.55 13.40 13.25 13.00 12.014.0 11.10 11.05 10.85 10.70 10.55 10.35 14.016.0 9.20 9.10 8.90 8.80 8.60 8.45 16.018.0 7.70 7.65 7.45 7.40 7.15 7.05 18.020.0 6.60 6.55 6.35 6.25 6.05 5.95 20.022.0 5.65 5.65 5.45 5.40 5.15 5.10 22.024.0 4.95 4.90 4.70 4.70 4.45 4.40 24.024.5 4.80 4.80 4.60 4.50 4.30 4.30 24.5



Radius (m) Radius (m)6.9 30.10 29.90 29.80 29.40 29.50 28.90 6.97.0 29.50 29.25 29.20 28.80 28.85 28.25 7.08.0 24.35 24.15 24.05 23.75 23.75 23.25 8.09.0 20.65 20.45 20.35 20.05 20.05 19.60 9.010.0 17.80 17.65 17.50 17.30 17.20 16.85 10.012.0 13.75 13.65 13.50 13.30 13.20 12.95 12.014.0 11.05 10.95 10.80 10.65 10.50 10.30 14.016.0 9.10 9.05 8.85 8.75 8.60 8.40 16.018.0 7.65 7.60 7.40 7.30 7.10 7.00 18.020.0 6.50 6.45 6.25 6.20 6.00 5.90 20.022.0 5.60 5.55 5.35 5.30 5.10 5.00 22.024.0 4.85 4.80 4.60 4.60 4.35 4.30 24.026.0 4.25 4.20 4.00 4.00 3.70 3.65 26.027.1 4.00 4.00 3.70 3.70 3.40 3.40 27.1

Notes:1. Capacities are the maximum allowable and based on machine standing level on firm supporting surface under ideal job conditions.2. Capacities are in metric tones, and are not more than 78% of minimum tipping loads except the figures surrounded by bold lines




10 3010 30 10 30

10 30 10 30 10 30




Main Boom with Crane Jib



23





Radius (m) Radius (m)7.5 26.50 26.30 26.20 25.90 25.90 25.40 7.58.0 24.15 23.95 23.90 23.55 23.55 23.05 8.09.0 20.45 20.30 20.20 19.90 19.90 19.45 9.010.0 17.65 17.50 17.35 17.10 17.05 16.70 10.012.0 13.60 13.50 13.35 13.20 13.10 12.80 12.014.0 10.90 10.80 10.65 10.50 10.40 10.15 14.016.0 8.95 8.90 8.75 8.60 8.45 8.30 16.018.0 7.50 7.45 7.25 7.15 7.00 6.85 18.020.0 6.35 6.30 6.15 6.05 5.85 5.75 20.022.0 5.45 5.40 5.20 5.15 4.95 4.90 22.024.0 4.70 4.70 4.50 4.45 4.20 4.10 24.026.0 4.10 4.05 3.85 3.80 3.55 3.45 26.028.0 3.55 3.50 3.25 3.25 2.95 2.90 28.029.7 3.20 3.10 2.90 2.90 2.60 2.60 29.7



Radius (m) Radius (m)8.0 24.05 23.85 23.80 23.45 23.50 22.95 8.09.0 20.35 20.20 20.10 19.80 19.80 19.40 9.010.0 17.55 17.40 17.30 17.05 17.00 16.65 10.012.0 13.55 13.45 13.30 13.10 13.05 12.75 12.014.0 10.85 10.75 10.60 10.45 10.35 10.10 14.016.0 8.90 8.85 8.70 8.55 8.40 8.25 16.018.0 7.45 7.40 7.20 7.10 6.95 6.80 18.020.0 6.30 6.25 6.10 6.00 5.85 5.70 20.022.0 5.40 5.35 5.15 5.10 4.90 4.80 22.024.0 4.65 4.60 4.45 4.35 4.15 4.05 24.026.0 4.05 4.00 3.75 3.70 3.45 3.40 26.028.0 3.45 3.40 3.20 3.15 2.90 2.80 28.030.0 2.95 2.95 2.70 2.65 2.40 2.35 30.032.0 2.55 2.50 2.30 2.25 2.00 1.95 32.032.3 2.50 2.50 2.20 2.20 2.00 1.90 32.3



Radius (m) Radius (m)8.6 21.60 21.40 21.30 21.00 21.00 20.60 8.69.0 20.20 20.05 19.95 19.65 19.65 19.25 9.010.0 17.45 17.25 17.15 16.90 16.90 16.50 10.012.0 13.45 13.30 13.20 13.00 12.95 12.65 12.014.0 10.75 10.65 10.50 10.35 10.25 10.00 14.016.0 8.80 8.75 8.60 8.45 8.30 8.10 16.018.0 7.35 7.25 7.10 7.00 6.85 6.70 18.020.0 6.20 6.15 6.00 5.90 5.75 5.60 20.022.0 5.30 5.25 5.05 5.00 4.80 4.70 22.024.0 4.55 4.50 4.30 4.25 4.00 3.90 24.026.0 3.90 3.85 3.65 3.55 3.35 3.25 26.028.0 3.30 3.30 3.05 3.00 2.75 2.70 28.030.0 2.80 2.80 2.55 2.50 2.25 2.20 30.032.0 2.40 2.35 2.15 2.10 1.85 1.80 32.034.0 2.00 2.00 1.75 1.75 1.50 1.45 34.034.9 1.90 1.90 1.60 1.60 1.40 1.30 34.9

10 3010 30 10 30

10 3010 30 10 30

10 3010 30 10 30


24




Radius (m) Radius (m)9.1 19.50/9.1 19.50/9.1 19.40/9.1 19.20/9.1 18.70/9.1 18.50/9.1 9.110.0 17.35 17.20 17.10 16.85 16.80 16.45 10.012.0 13.35 13.25 13.15 12.90 12.85 12.55 12.014.0 10.70 10.60 10.45 10.30 10.20 9.95 14.016.0 8.75 8.65 8.50 8.35 8.25 8.05 16.018.0 7.25 7.20 7.05 6.95 6.80 6.65 18.020.0 6.15 6.05 5.90 5.80 5.65 5.55 20.022.0 5.20 5.15 5.00 4.90 4.75 4.60 22.024.0 4.45 4.40 4.20 4.15 3.95 3.80 24.026.0 3.80 3.75 3.50 3.45 3.25 3.15 26.028.0 3.20 3.15 2.95 2.85 2.65 2.55 28.030.0 2.70 2.65 2.45 2.40 2.15 2.10 30.032.0 2.25 2.25 2.00 1.95 1.75 1.65 32.034.0 1.90 1.85 1.65 1.60 1.35 1.30 34.036.0 1.55 1.55 1.30 1.30 1.30 /34.5 1.30 /34.2 36.038.0 1.40 /37.5 1.30 /37.5 1.30 /36.2 38.0



Radius (m) Radius (m)9.7 17.50 17.40 16.90 16.80 16.30 16.00 9.710.0 17.20 17.05 16.75 16.60 16.15 15.90 10.012.0 13.25 13.15 13.00 12.80 12.75 12.45 12.014.0 10.55 10.45 10.35 10.15 10.10 9.85 14.016.0 8.65 8.55 8.40 8.25 8.15 7.95 16.018.0 7.15 7.10 6.95 6.85 6.70 6.55 18.020.0 6.05 5.95 5.80 5.70 5.60 5.45 20.022.0 5.10 5.05 4.90 4.80 4.65 4.50 22.024.0 4.35 4.30 4.10 4.00 3.80 3.70 24.026.0 3.65 3.60 3.40 3.30 3.10 3.00 26.028.0 3.10 3.05 2.80 2.75 2.55 2.45 28.030.0 2.55 2.55 2.30 2.25 2.05 1.95 30.032.0 2.15 2.10 1.90 1.85 1.60 1.55 32.034.0 1.75 1.75 1.50 1.45 1.30 /33.7 1.30 /33.4 34.036.0 1.45 1.40 1.30 /35.3 1.30 /35.1 36.038.0 1.30 /37.0 1.30 /36.8 38.0

10 3010 30 10 30

10 3010 30 10 30



25

Clamshell SpecificationsDimensions and Specifications

A

3280

51956170

3380

C

1750

12000 to 18000 R406550401000

1145

1225

5780

B

Working Radius

HH1

H2D

L 3530

Clamshell SpecificationsBucket Capacity m3 0.8/1.0/1.2Allowable Gross Weight t 6.0Boom Length m 12.00 to 18.00Max. Digging Depth m 36Suspend Line Speed m/min *75

Wire Rope Diameter 22 mmOpen/Close Line Speed m/min *75Boom Hoist Line Speed m/min *62

Wire Rope Diameter 16 mmBoom Lower Line Speed m/min 62Ground Contact Pressure kPa (kgf/cm²) 78.5 (0.80) (w/ 12m Boom + 1.2 m3 Bucket)Operating Weight t 67.3 (w/ 12m Boom + 1.2 m3 Bucket)

NOTE : 1.*Line speeds will vary with the load. 2.Data is expressed in Sl units, followed by conventional units in ( ). 3.Other specifications, not shown are similar to those for the cranes.

Capacity ( m3 ) Weight( t ) A (mm) B (mm) C (mm) H (mm) H1 (mm) Use

0.8 2.00 1880 970 2230 2270 2980 Excavation1.0 2.45 2020 1070 2430 2430 3150 Excavation1.2 3.10 2020 1070 2430 2430 3150 Excavation1.2 2.40 2000 1160 2650 2600 3240 Light Service

Boom Length m 12 15 18Boom Angle ° 35 45 55 65 35 45 55 65 35 45 55 65Working Radius m 11.3 10.0 8.4 6.7 13.7 12.1 10.2 8.0 16.2 14.2 11.9 9.3Allowable Gross Weight t 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0Lifting Height (w/1.2m3 bucket L (D + H2) m 38.8 40.5 41.9 42.9 40.5 42.6 44.3 45.6 44.2 44.7 46.8 48.4Max. Digging Depth D m 36

Dumping Height H2

0.8m3 bucket m 3.2 4.9 6.3 7.3 4.9 7.0 8.7 10.0 6.6 9.1 11.2 12.81.0m3 bucket m 3.0 4.7 6.1 7.1 4.7 6.8 8.5 9.8 6.5 8.9 11.0 12.61.2m3 bucket m 2.8 4.5 5.9 6.9 4.5 6.6 8.3 9.6 6.2 8.7 10.8 12.4

Working Ranges

Specifications Gross Rated Load Table

Clamshell Bucket

1. Working radius is the horizontal distance from the swing center to the gravity of lifted load.2. The rated loads for clamshell do not exceed 70% of tipping load.3. The rated loads shown are upper limits determined by the following equation. Please select a bucket in such a manner that its rated load does not exceed the rated load shown below, according to kinds of the loads handled. Rated load = Bucket capacity (m3) x Specific gravity of load (t/m3) + Bucket weight (t)4. Even if using different capacity of the bucket according to kinds of load, don't exceed the rated load.5. The counter weight is 23.0 t.6. Figures described as ○○ / ○○ in the tables indicate rated load (t) / working radius (m).

Unit ; tWorking Radius

(m) 12.006.7 6.007.0 6.008.0 6.009.0 6.00

10.0 6.0012.0 6.00 / 11.314.016.016.2

6.00 / 13.76.006.00

15.00

6.00

6.00 / 9.36.00 6.00

6.006.00

18.00

6.006.00

Boom Length (m)

Clamshell SpecificationsDimensions and Specifications


26

Weights and Dimensions of Disassembled UnitsDescription Qty Dimensions (mm) Weight (kg)

Base Crane with :Boom Base

Front Winch Wire RopeBoom hoist wire rope

1

12100

3500

3375 39800

Base Crane with :Front Winch Wire RopeBoom Hoist Wire Rope

1

3500

8065

3375 38300

Counter Weight (Base) 1

3285 750

11158600

Counter Weight (Middle) 1

3285 900

11158400

Counter Weight (Top)(Left Side) 1

945

1115

820

3000

Counter Weight (Top)(Right Side) 1

900

1115

820

3000

Weights and Dimensions of Disassembled UnitsWeights and Dimensions List

Weights and Dimensions of Disassembled UnitsWeights and Dimensions ListTECHNICAL DATASCX700E

Comply with the regulations when transporting."Weight" refers to the mass of each single unit.

27

Weights and Dimensions of Disassembled UnitsWeights and Dimensions List TECHNICAL DATA SCX700E

Weights and Dimensions of Disassembled UnitsDescription Qty Dimensions (mm) Weight (kg)

Upper Spreader 1

1680 275

705250

Boom Basewith Connect Pins

with Boom Back Stops1

6160 1640

1715

1200

Boom topwith Pendant Ropes 1

64151500

1605

1185

Aux. Sheavewith Connect Pin 1

1250 815

850205

3 m Boom Insertwith Connect Pins

without Pendant Ropes1

3115 1515

1570 310



1570

6115 1515

520



9115 1515

1570 710

28

Weights and Dimensions of Disassembled Units

Description Qty Dimensions (mm) Weight (kg)

Jib Base with :Foot Pin

Connect PinsJib Strut

Connect Pins

1

4615

850

860

475

Jib Top 1

4925

780

1110 250

4.5 m Jib Insertwith Connect Pins 1

4580

640

675

130

70 t Hook 1

1845

660

455

800

40 t Hook 1 1585

620

340

410

15 t Hook 1 1360

620

285

320

6.5 t Hook 1

870

250

180

Weights and Dimensions of Disassembled UnitsWeights and Dimensions ListTECHNICAL DATASCX700E

29

Equipment List Standard and Optional Equipment TECHNICAL DATA SCX700E

Equipment List Standard and Optional Equipment

: Standard : Optional

Item Lift Crane Notes

Basic Items

Winch with Free Mechanism ○ Front and Rear WinchBrake Pedals for Front and Rear Winch ○Crawler Extend / Retract Device ○Working Light (× 2) ○Back Mirror (Left and right) ○Wiper with Washer (Front window) ○Room Lamp ○Cigar Lighter Socket (24 V) ○Ashtray ○Cup Holder ○AM / FM Radio ○Air Conditioner ○ Full AutomaticAccelerator Lever ○Accelerator Pedal (Right side) ○Hydraulic Pump Flow Rate Select Switch ○ Max. or Min. RateElectric Fuel Pump ○Travel Operation Pedal ○Under Cover ● Left SideClear Roof Cover ● Smoke TintedCounter Weight Lifting Wire Rope ○3 m Boom Insert ●6 m Boom Insert ●9 m Boom Insert ●Parts Set for 9 m Crane Jib (9 m Basic jib, Anti-two block, Jib strut) ●4.5 m Crane Jib Insert ●Parts Set for Auxiliary Sheave (Auxiliary sheave, Auxiliary sheave anti-two block) ○70 t Hook (5 sheaves) ●40 t Hook (3 sheaves) ●15 t Hook (1 sheave) ●6.5 t Hook ●Rear Winch Wire Rope ○Spring Type Tagline ●

Meters & Lamps

Coolant Temp.Gauge ○Fuel Gauge ○Hourmeter ○Swing Brake Indicator ○Alternator Indicator ○Engine Oil Pressure Indicator ○Air Filter Restriction Indicator ○Overheat Indicator ○Preheat Indicator ○

Safety

Moment Limiter ○Anti-Two Block ○Boom Hoist Limiting Device ○Secondary Boom Over Hoist Prevent Device ○Swing & Travel Alarm ○3 Color Percentage Indicator ○

Drum LockFront Winch ○Rear Winch ○Boom Hoist Winch ○ Automatic

Swing Lock ○ Lock Pin for TransportGate Lock Lever ○Auto Stop Override Select Key Switch ○Auto Stop Override Switch ○

M E M OSCX700E

• We are constantly improving our products and therefore reserve the right to change designs and speafications without notice. • Units in this specification are shown under International System of Units; the figures in parenthesis are under Gravitational System of Units as old one.

9-3, Higashi-Ueno 6-chome, Taito-ku, Tokyo 110-0015, JapanPhone: 81-3-3845-1387 Facsimile: 81-3-3845-1394http://www.hsc-cranes.com

Specifications Lifting Capacities - hsc-crane. · PDF fileSpecifications & Lifting Capacities....

Documents

Transcript of Specifications Lifting Capacities - hsc-crane. · PDF fileSpecifications & Lifting Capacities....