Special Tools for Flute 2013 Woodwind

8/10/2019 Special Tools for Flute 2013 Woodwind

1/6

6

E-Mail: [email protected] web: www.boehmtools.de

- 1 -(9.0. tools for woodwind instruments 13/14)

685

TOOLS FOR WOODWIND INSTRUMENTS

9.0. SPECIAL TOOLS FOR FLUTE

EXPANDER FOR FLUTESThis apparatus is used on loose-fitting flute head joints and main bodies

(and sax necks!) to correct the fit quickly and effortlessly.

-554- expander for flutes and sax necks (alto - baritone).

SHRINKING TOOL FOR FLUTE HEAD JOINTS AND BODIESThis new and highly efficient tool shrinks the radius of the tubing quickly and precisely. This tool comes with exchangeable

slotted sleeves, so it can be used with different diameters of tubing.

A counter-pressure-screw controls the shrinking process.

-685 shrinking tool for flute head joints and bodies,

with 4 interchangeable slotted sleeves

dia. 19.620.05 mm

No.685 can be used to shrink soprano

sax necks.You need additionalSleeves no. 685/1

-685/1- slotted sleeves, set of 4 pc,

dia 16.5, 17.0, 17,5 and 18.0mm

for soprano sax necks

(no picture)

DRAW PLATE FOR FLUTE HEAD JOINTSThis draw plate serves the same purpose as the shrinking dies

no. 553 or 685, but makes it possible to shrink in exact 1/100 mm steps

by using interchangeable rings.

-585/5- draw plate with 10 rings, hardened,

19.50 - 19.85mm diameter (selected diameters,

approx. 3/100mm steps).

-585/6- draw plate with two boreholes,

for crooked head joints;

without rings.

(For rings see 585/7).

-585/7- ring for draw plate specify the diameter

(range 19.0 - 19.85 mm).

554

585/5

585/6


2/6

6



589AFL

657/2

TAPERED ROD FOR FLUTES

Evenly tapered rod- with tuning markers

for the flute stoppers

-657/1- tapered rod for

C-flute/ alto-flute

-657/2- tapered rod for

C-flute/ alto flute/ bass flute

ROD HOLDER FOR VISE WITH DOVETAIL GRIPNew vise grip for rods with dovetail, made of polyamide, an extremely firm plastic material.

It holds rods tightly in any position in the vise. The two jaws are held in the vise

by small magnets, so they can be put in any position in the vise.

-152DP/1 vise grip, with dovetail,

opening range 10 20 mm dia.,

with magnets

EXPANDABLE DENT BALL FOR FLUTESThis tool is used for removing dents and rounding out-of-round tubing as well as expanding loose or badly fitting flute head

and foot joints. Our precision made, six-section expander is slightly oval shaped and is expanded equally and smoothly by

means of a long fine thread that allows micrometer-type adjustment. It is of polished steel with hard chrome plating and doesnot scratch the tubing. Apply lubricant during operation. The tool can be hand-held or fixed in vise.

-589- expandable dent ball for flute, 18.9mm dia.,

with stop ring

-589AFL- expandable dent ball for alto flute,main rod with 2 pc. bolts dia 24 and 25mm

(for alto flutes you need two diametres)

FLUTE MANDRELS FOR FLUTE

-556- mandrel for flute bodies,

cylindrical,

18.9 mm diameter x 650 mm,

one end rounded.

-557- mandrel for flute head joints,

tapered, slightly curved.

589

152DP/1

Tuning markers for the flute stoppers

556-557


3/6

6



DENT ROLLER FOR FLUTE

-066KR-FL- dent roller with radius, diameter for

C-flutes, to use with mandrels no.556 and 557

DENT ROLLERS FOR FLUTE

-558- hand roller for rolling out dents

in flutes, with radius, hardened,

ball-bearing mounted.

To be used with rod no. 556

SMALL DENT ROLLER FOR FLUTETwo new handy and stable rollers to remove dents from flute bodies and head joints. Different shapes taper and radius

make it possible to get close to the tone hole rim and to the post plate/bar. Do not forget to use a mandrel/rod inside the

tubing ( nos 556, 557) when working with the rollers.

-558K dent roller for flute, with taper, hardened

-558RS- dent roller for flute, with radius, hardened

BURNISHER FOR FLUTESlim burnisher with flute radius, tapered, hardened and finished.

Use a mandrel/rod inside the tubing ( nos 556, 557) when using the burnisher.

-558P burnisher for flute, hardened on top

558

558P

558RS

558K

066KR-FL


4/6

6



684

DENT BALLS FOR FLUTE HEAD JOINTSDent balls with flat curve for the curved taper in flute heads.

-584/1- dent balls for flute head joints, set of 6 pieces,

threaded, 16 - 18.5 mm dia., with threaded rod.

DENT TOOL FOR BENT FLUTE HEAD JOINTSThis dent tool makes it easy to eliminate dents from a bent head joint. It is supplied

with 5 balls so that it can be used for the standard headjoint sizes.

-684- dent tool for bent head joints, rod with joint,

with 6 balls dia 18.0 18.5 mm

PARALLEL PLIERS FOR GROMMETSThese pliers are used for pressing the grommet (ring) into the open flute key.

Plastic pads in the pliers prevent the scratching of grommet and key.

-682- parallel pliers for grommets (rings),

with plastic inserts.

KEY PIN REMOVAL PLIERS

Special parallel pliers for the removal of the key pins of flutes and other woodwind instruments.To fit any key configuration, there are two different anvils and two different removal punches.

A very handy and yet stable tool!

-581- key pin removal pliers (parallel pliers), with 2 interchangeable brass anvils and

2 interchangeable removal punches.

584/1

682

581


5/6

6



655

EXPANDER FOR OPEN HOLE CUPSThis tool is used for improving the pad seat.

It expands the hole to make the retaining ring

fit tightly.

-588/5- Expander for open tone hole

cups, for holes 6.9-7.2mm dia.

SPECIAL PLIERS FOR FLUTE CUPS

Jaws are parallel at opening of 4mm

-655- special pliers for

flute cups

FLUTE CUP ALIGNMENT TOOLSThese tools grip the cup at its base rim without damaging it as there are

plastic inserts. By turning the spindle the cup is fastened in the tool and can be

aligned in any direction. Order the set or individually!

-588- flute cup alignment tools, set of 4.

- 588/1- for cups 19.5 - 21 mm outer diameter

- 588/2- for cups 18.5 - 20 mm outer diameter

- 588/3- for cups 17.5 - 19.5 mm outer diameter

- 588/4- for cups 12.5 - 13.5 mm outer diameter

PAD IRONING TOOLSMade of rust-free, hardened spring steel 0.5 mm thick.

These tools are used for smoothing the skin of pads.

-537/1- pad ironing tool, set of 5 pc., for flute,clarinet, oboe

-537/11- pad ironing tool, 1 pc, for flute only.

TONE HOLE LEVELLING TOOLThis tool is used for improving the pad seat by smoothing

down the tone hole rim. The interchangeable pilots are made

of plastic so the risk of scratching the instrument is avoided.

Can be used as a hand tool or in spindle no. 501 or bench

motor no.505R.

-583- tone hole levelling tool ,hardened, for flutes,

set of 2 pieces, with 10 pieces plastic pilots.

588

588/5

537/1

583


6/6

6



PUNCHING TOOL FOR FLUTE PADSA punch that cuts pads for open keys from pads for

closed keys New set for more sizes.

-583/6A- punching tool, 3 punches for dia.

8.5 9 9.5 mm hole,

5 brass guides for 10 different diameters

for pad diameter 16.4 to 19.3 mm

Use a soft pad (wood, leather,soft plastic) as surface.

CUTTING TOOL FOR FLUTE PAD WASHERSThis tool is used to cut out cardboard or paper rings or disks.

It consists of 16 pieces for the inner diameter and 9 pieces

for the outer diameter. Any insert for the inner diameter

can be combined with any insert for the outer diameter.


-583/5A- cutting tool for flute pad washers,

complete with punch and

9 pieces for the outer diameter

(15.5-19.5mm dia in steps of 0.5mm)

16 pieces for the inner diameter

(4.5-5.0-5.5-6.0-6.5-7.0-7.5-8.0-8.5-9.0-

9.5-10.0-10.5-11.0-11.5-12.0 mm dia.)

HOLLOW PUNCHESNew set for punching and making discs from

cardboard,felt, plastic, leather and similar material.

The difference between each size is 0,5mm.

Comes with plate, holder and brass guide for

straight punching!

-641/3,5-12- hollow punches, set of 18 pc.,

dia 3,5 12mm, steps of 0,5mm,

with brass guide for

straight punching


DENT REMOVER FOR FLUTESThis tool, for flute main bodies and foot joints, has a profile rod of the appropriate diameter to remove dents by pushing them

out from the inside. The opposite piece (sleeve) of the profile rod remains fixed. This dent removal apparatus does not work

like a spacing rod, it avoids the widening of the whole tube.

-587- dent remover for flutes, 18.9 mm dia. Particularly

useful for indented posts on the B key.

583/6A

583/5A

641/3,5-12

587

Special Tools for Flute 2013 Woodwind

Documents

Transcript of Special Tools for Flute 2013 Woodwind