SPC Nov Dec2012draftlores
-
Upload
riverland-welding-and-tool-supplies -
Category
Documents
-
view
233 -
download
2
Transcript of SPC Nov Dec2012draftlores
Infrared LaserGuidedThermometer• Dual laser technology (twin dots)• Rapid detection function• Automatic data hold• OC/ OF switch• Set high & low alarms• Temperature range -50O
to 550OC (-58O to1022OF)
PROUDLY DISTRIBUTED BY:
Austech Industries 2012 ©COPYRIGHT 1
SPECIALS AVAILABLE NOVEMBER, DECEMBER 2012
3.2hp InverterGenerator• Max 2000w, rated 1600w• From 52dB(A)• 4.1lt tank capacity• Pull start
POWERED BYTORINI ENGINEWITH 3 YEARWARRANTY
NEW
NEW ENVIRONMENTALY FRIENDLY• Patented engine with big volumemuffler to increase fuel efficiencyand reduce noise
• Patented permanent magnet invertergenerator with ESC intelligentlycontrols rpm to reduce noise and fuel consumption
• Patented 3 way cooling system to lower runningtemperature and extend engine life
• Patented exhaust gas circulation – exhaust gaspasses through 2 cavities for double oil separation,decreases oil consumption and extends engine life
• Single cylinder, 4 stroke, forced air cooling, OHV engine• Continuous running time at rated power = 4.2hrs• Meets EPA & CARB (amongst the world’s strictestenvironmental protection standards)
®
Trade Tyre Inflator• Tyre inflator and deflator• Dial gauge• High qualityhose andfittings
LED Magbase WorkLight• Ultra bright• 30 LED – 1200LUX• 5 LED spot lights –200LUX
Electrical Digital Multimeter• AC/DC voltage (Max 600VAC/600VDC)DC current (Max 10A),resistance,diode test
Through-Handle 4pc Pry Bar Set• 1/4"x8", 3/8"x12",7/16"x18",7/16"x24"
Aluminium 2 Jaw Hand Riveter
1/2” DrImpactWrench• 190mm long• 2.5kg• Max torque425ft/lbs
®
• Takes 2.4-4.8mmaluminium, steel &stainless steel rivets
$995Ti2000
$69SP30839 SP69020 SP-1145A
$129
$89$79$29
$1995 $199
SP62012 SP81455 SP-900
SP62020
BONUST81470 HAND HELD
LED INSPECTION LIGHT (FLUORESCENT
EFFECT) WITH EVERY TI2000
2 Austech Industries 2012 ©COPYRIGHT
7hp AVR PureSine WaveGenerator• 4kva pull start• 3200w max,2900w rated
• 2 power outlets• 50hz/240v• 18lt tank capacity
7hp ConstructionSeries Generator• 4kva pull start• 3000w max, 2800wrated
• IP66 rated poweroutlets & RCD
• Handle & wheel kitincluded
SW6800Epictured
Pure Sine Wave
Automatic Voltage ControlAVRAVR
Commercial quality engines, highquality sine wave alternators andautomatic voltage regulation is justsome of what makes a genuine Torinigenerator. Reliability, fuel efficiency,low noise, portability and utmost faiththat it will work first time, every timeis what Torini owners take for granted.
Torini Generators taken to anew level in addition to all theprofessional features, thesemodels feature:• IP66 ratedpower outletsand RCD
• Handle andwheelkit included
• 8.1kva• 68dB(A)• 25lt tank capacity
15HP CONSTRUCTIONSERIES ELECTRIC STARTGENERATOR
POWERED
BY TORINI ENGINE
WITH 3 YEARWARRANTY
MODEL HP KVA START PRICESW2800 6.5hp 2.8kva Pull start $599SW6800E 13hp 6.8kva Electric start $1595SW8100E 15hp 8.1kva Electric start $1995
SC2500pictured
www.facebook.com/sptoolsracing
MMOORREE GGRRUUNNTT TTHHAANN AA VV88 SSUUPPEERRCCAARR
Automatic Voltage ControlAVRAVR
POWERED
BY TORINI ENGINE
WITH 3 YEARWARRANTY
®
GENERATORS
®
MODEL HP KVA START PRICESC2500 6.5hp 2.5kva Pull start $395SC6500 13hp 6.5kva Pull start $799SL3500 6.5hp 3.5kva Pull start $599SL6800E 13hp 6.8kva Electric start $1199
2hp Portable Generator• Recoil start • 800w max, 650w rated• 60dB(A) • 2 stroke engine• 50hz/240v • DC: 12v/8.3amp• 4.2lt tank capacity - 6.3 hours • 21kg
2.8hp Portable Generator• Recoil start• 950w max, 900w rated• 63dB(A) • 4 stroke engine• 50hz/240v • DC: 12v/8.3amp• 5.5lt tank capacity - 6 hours• 28kg
POWERED
BY TORINI ENGINE
WITH 3 YEARWARRANTY
NEW NEW$749 $880SWC4000SW4000
$1995SWC8100E
SC960$179
SC1200$329
Austech Industries 2012 ©COPYRIGHT 3
®
ELECTRIC POWERED
5.5hp Pressure Washer• 5.5hp OHV Torini engine • 2200psi working pressure
• 8.3L/min water flow• 8m hose • Stainless steel lance
POWERED
BY TORINI ENGINE
WITH 3 YEAR WARRANTY
2.6hp Pressure Washer• 2.6hp OHV Torini engine• 5.5L/Min water blow• 1400psi working pressure • 2.0kw @ 4000rpm• 8m hose• Stainless steel lance
POWERED
BY TORINI ENGINE
WITH 3 YEAR WARRANTY
1400w ElectricPressure Washer• Max pressure 1600psi
• 6.16L/min flow rate • 5m hose• Adjustable pencil point/fan jet lance
• Foam gun • Aluminium pump
1700w Electric Pressure Washer
• Max pressure 1885psi• 6.16L/min flow rate • 5.5m hose
• Adj pencil point/fan jet lance• Turbo lance • Foam gun
• Hose reel storage • Aluminium pump
1800w ElectricPressure Washer• Max pressure 2050psi
• 7L/min flow rate• 2 wheel trolley• Alloy pump • Auto throttle stop• 5m cable• Water filter• Turbo nozzle• 8m reinforced hose
• Semi industrial
2800w Electric Pressure Washer
• Max pressure 2300psi • Aluminium pump withstainless steel plunges • 8m hose • Turbo lance• 15amp plug • Industrial
2100w Electric PressureWasher• 7L/min flow rate• 2030psi max pressure
• 8m steel braided hose
• Aluminium pump• Semi industrial
SPW590$599
SPW490$499
SPW383$249
PPRREESSSSUURREE WWAASSHHEERRSS®
PETROL POWERED
Follow us @sptoolsracing
6.5hp Pressure Cleaner• 6.5hp OHV Torini engine• 3550rpm • 8m hose• Stainless steel lance• 3200psi working pressure• 9.5L/min water flow
POWERED
BY TORINI ENGINE
WITH 3 YEARWARRANTY
TPW3600$799
15hp Pressure Cleaner• 15hp OHV Torini engine • 3400rpm • 10m hose • Stainless steel lance• 4000psi working pressure• 18.2L/min water flow• Heavy duty powder coated folding frame
POWERED
BY TORINI ENGINE
WITH 3 YEARWARRANTY
POWERED
BY TORINI ENGINE
WITH 3 YEARWARRANTY
WATER PUMP6.5hp Petrol HighPressure Water Pump• OHV 4 Stroke • 300L/min max flow• 6m max suction • Max head to 42m• 1.5” inlet size • 1x1.5” or 2x1” outlet size
TWP200$495
Car/Boat/Caravan• Safe for foliage & lawn• Pentrates & lifts heavy grime & oil
PRESSURE WASHER CLEANERS
Concrete Surfaces• Safe on most cement & masonry surfaces
• Breaks down grease, oil & grime
General Purpose• Safe for plants
• Penetrates & liftsdirt & grime
CC2
GP2
CBC2
$10 EACH
TPW4500$1595
SPW445$369
SPW141$149
SPW2500P$499
SPW1600P$399
ALL
4 Austech Industries 2012 ©COPYRIGHT
Subscribe to our channel: sptools
LED Magbase WorkLight• 20 LED – 1000LUX• Ultra bright • IP65 - Dustproof and water resistant
SMD LED Magbase WorkPocket Super Brilliant
Hand Held SMD LEDInspection Light(Fluorescent Effect)• 180 degree light spread (compared to 30 degree standard LED)
Under Bonnet SMD LED Work Light(Fluorescent Effect)• 180 degree light spread (compared to 30 degree standard LED)
SP81450$69
Ultra Bright Led Work Light• 60 LED – 800LUX• Ultra broad & bright• IP68 – Dustproof andwaterproof
LED Pocket Inspection Light• Ultra bright with dual function torch & lamp
• Ultra compact • Light weight• Magnetic
SP81441$1995
SP81456
$89
NEW
NEW
SP81470
$89
SP81465
$199
CCOORRDDLLEESSSS LLIIGGHHTTIINNGG
SP81458$149
SP81445
$79
NEW
SMD LED Magbase Work SuperBrilliant
250% BRIGHTER
250% BRIGHTER
NEW
Austech Industries 2012 ©COPYRIGHT 5
www.facebook.com/sptoolsracing
1/2” INDUSTRIAL High Torque Drill• 18v platform• 2 Speed: Low 0-380rpm, High 0-1380rpm
• Charging Time: 1 hour auto cut-off • 2 year warranty (Battery 1 year) • Includes blow mould protective case
1/2” Dr INDUSTRIAL Hammer Drill• 18v platform• 2 Speed: Low 0-700rpm, High 0-2440rpm
• Torque: 40N-m • Charging Time: 1 hour auto cut-off • 2 year warranty (Battery 1 year) • Protective blow mould case
SP82110$399
1/2” Dr INDUSTRIALDrill/Driver• 18v platform• 2 Speed: Low 0-700rpm, High 0-2400rpm
• Charging Time: 1 hour auto cut-off • 2 year warranty (Battery 1 year) • Includes blow mould protective case
BONUS CAP
BONUS CAP
SP81231$299
12v INDUSTRIAL2pc Combo Kit • 12v mini 1/4”dr impact driver (SP81142)
• 12v 2 speed mini 3/8” drill(SP81212)
• 1pc x battery charger
• 2 year warranty (Battery 1 year)
Batteries
2 x 1.5Ah
BONUS CAP
12v Pop Rivetor/Drill Kit• 3/8” capacity drill 2250rpm – ideal for all high speed drilling
• 3/16” capacity pop riveter
SP82150$585
BONUS CAP
Batteries
3 x 1.5Ah
Batteries
2 x 3.0Ah
Batteries
2 x 3.0Ah
SP81233$349
SP81243$399
CCOORRDDLLEESSSS FFOORR EEVVEERRYY TTRRAADDEE
NEW
BONUS CAP
Batteries
2 x
6 Austech Industries 2012 ©COPYRIGHT
Follow us @sptoolsracing
3/8” Dr INDUSTRIAL 2 Speed Mini Drill• 12v platform• 2 speed: Low 0-530rpm, High 0-2250rpm
• Charging Time: 1 hour auto cut-off
• 2 year warranty (Battery 1 year)
• Protective blow mould case
1/4” Dr HexScrewdriver• Voltage: 3.6 volt• 2 Speed: Low 220rpm/min High 450rpm/min
• Charging Time: 1 hour auto cut-off
• Includes blow mould protective case
• 2 year tool warranty (Battery 1 year)
BONUS CAP
12v 400ml BarrelCapacity Caulking GunWorks with all standardsize cartridges
12v 600ml Barrel Capacity Caulking GunWorks with all standard size sausages
BONUS CAP
Batteries
2 x 1.5Ah
12v INDUSTRIAL Mini Ratchet• 3/8” capacity • No-Load Speed: 250rpm• Torque: 80N-m• Charging Time: 1 hour auto cut-off • 2 year warranty (Battery 1 year)
• Protective blow mould case BONUS
CAP
Batteries
2 x 1.5Ah
FREE SP20240 SOCKET SET
WITH EVERY SP81613
2” (50mm) Gasket Sander• 12v platform • 8,000rpm• Charging Time: 1 hour auto cut-off
• 2 year warranty (Battery 1 year)
• Protective blow mould case BONUS CAP
BONUS CAP
Batteries
2 x 1.5Ah
Batteries
2 x 1.5Ah
Batteries
2 x 1.5Ah
1/4” Dr INDUSTRIAL Impact Driver• 18v platform• No-Load Speed: 2000rpm• Torque: 250N-m • Charging Time: 1 hour auto cut-off • 2 year warranty (Battery 1 year) • Protective blow mould case
50% MORE POWER
THAN MOST
COMPETITORS
BONUS CAPBatteries
2 x 3.0Ah
SP81363$459
SP81362$395
SP81613$289
SP81201$139
SP81342$249
SP81212$199
SP81146$499
PPRROOFFEESSSSIIOONNAALL CCOORRDDLLEESSSS TTOOOOLLSS
Austech Industries 2012 ©COPYRIGHT 7
Subscribe to our channel: sptools
12v 1.5Ah Li-IonBattery• 16.2Wh
18v 3.0Ah Li-Ion Battery• 54Wh
3.6v Battery Charger• Input 100-240v~50/60Hz 15W
• Output 3.6v –-- 2A
BATTERIES & CHARGERS1 YEAR
WARRANTY ON
BATTERIES &CHARGERS
3.6v1.5Ah Li-IonBattery• 5.4Wh
12v-18v Battery Charger• Input: 100-240v~50/60Hz 90W• Output: 10.8-18v –-- 3.4A
18v Brushless Motor Angle Grinder• High efficiency• Low maintenance• Long life• Sparkless
SP81996$149
SP81982$69
SP81972$49
SP81990$88
SP81970$39
PROFESSIONAL CORDLESS TOOLS TTHHEE 1122 OORR 1188VV PPLLAATTFFOORRMMSS AARREE SSTTAANNDDAARRDD AACCRROOSSSS TTHHEE RRAANNGGEESSKKIINNSS
12v INDUSTRIALMini Ratchet
12v INDUSTRIALMini ImpactWrench
12v INDUSTRIALMini Impact Driver
18v INDUSTRIALImpact Driver
18v INDUSTRIALGrease Gun
18v INDUSTRIALShear
18v INDUSTRIALHIgh Torque Drill
18v INDUSTRIALCordless High Speed Drill
SP81522BU$235
SP81328BU$235
SP81112BU$159
SP81142BU$159
SP81233BU$179
SP81232BU$179
SP81146BU$259
SP81613BU$199
NEW
SP81312BU$299
8 Austech Industries 2012 ©COPYRIGHT
3/8” Mini Ratchet• Trade favourite for many years • 170mm long
®
3/8” Dr Ratchet Wrench• 254mm • 160rpm • 124ft/lbs
1/2” Dr Ratchet Wrench• 254mm • 160rpm • 124ft/lbs
®
1/2" Impact Wrench• 185mm long • 2.58kg• Max torque 600ft/lbs
® 3/4” Dr Impact Wrench• 950ft/lbs torque • High torque hammers deliver power fast
®
1/4” Dr Die Grinder • Rib textured handle
• 23000rpm ®
1/4”dr 90 Degree Angle Head Die Grinder• 160mm • 21000rpm
®
3/8” Dr IndustrialAir Drill• 2200rpm
1/2” Dr Industrial Reversible Pistol Drill• 500rpm
® ®
2.5mm Dust Free OrbitSander• 10,000rpm
5mm DustFree OrbitSander
2” GasketSander• 12000rpm• 50mm
®
Fine Discs• Pack of 4 fine discs for use on aluminium cylinder heads
Course Discs• Pack of 4 course discs for use on cast iron cylinder heads
3 Jaw Air Riveter • 4.8mm (3/16”) steel & s/steel, 6.4mm (1/4”) aluminium
3 Jaw Air Riveter • 4mm (5/32”) to 6.4mm (1/4”) all material
Air Nibbler• 1.6mm steel capacity
• 185mm
®
®
SSPP PPRROOFFEESSSSIIOONNAALL AAIIRR TTOOOOLLSS
www.facebook.com/sptoolsracing
SP-2307$299
SP-2305$199
SP-2215$195
SP-3600$199
SP-3605$199
SP-1330H$179
SP-2051$15
SP-2053$15
SP-1210$149
SP-1527$299
SP-1525$199
SP-1156TR$599
SP-1140EX$299
1/2”dr ImpactWrench• 167mm long• 1.9kg• 870L/min max, 261L/min av air consumption
• 780ft/lbs torque• Composite body
®
SP-1762$165
SP-1133SX-2
$149
SP-1133SX$149
SP-2200AH$149
SP-7145$399
Austech Industries 2012 ©COPYRIGHT 9
1.8mm Nozzle HighPressure Spray Gun• 1lt pot • 50psi • 1.22kg
®
1.4mmNozzle
®
Gravity Fed Spray Guns• 600ml pot • 50psi
2mmNozzle
®
High Pressure Spray Gun• 50psi • 2lt pot• Aluminium pot
3/16” Cap Pistol Type Pop Rivetor• 4.8mm (3/16”) max capacity
• 90psi • Weight 1.64kg
® Air Saw• 10000rpm • 1.6mm steel capacity• 10mm stroke length
®
16mm Staple Gun• 160pc load capacity • 60-100psi• Fasteners: “80” series 12.9mm crown, 3-16mm length
®
• Includes nail & staple gun & carry case
• Fasteners: “C1” series nails 15-50mm “90” series
staples 16-40mm
®
Nail & Staple Gun Kit
Retractable Hose Reelwith 15mHose• 10mm PVC hose
10mm x 15m Air Hose with Nitto Type Fittings
10mm x30m Air
Hose withNitto Type
Fittings
®
®
1/4” FilterRegulator• 25 micron filter• 2000L/min rated flow
• Set pressure: 8-125psi
SP PROFESSIONAL AIR TOOLS AAIIRR TTOOOOLLSS
Follow us @sptoolsracing
SX60-2$49
SX50-3$59
SX-70$139
SX50-1$59
TAR-40$129
®
3/8” Dr Reversible Drill• 1800rpm free speed
SX-530$89
SX-313$89
Framing Gun • 56-70pc load capacity • 70-120psi
• Fasteners: 34O D or clippedhead nails 50-90mm
®
S9034$149
S1850C$59
S8016$49
SFR-302$59
RHR-15$99 I66-15N
$29
I66-30N$59
10 Austech Industries 2012 ©COPYRIGHT
2.5hp • 150psi • Filter/regulator• 50lt tank • FAD 225L/min
3hp • 150psi • Filter/regulator• 50lt tank • FAD 251L/min
Cast Iron V-Twin Portable Air Compressors
XRV17pictured
3 YEARPUMP
WARRANTY
6.5hp Portable Air Compressor• 6.5hp Torini engine • Belt drive • 150psi • 60lt tank • OHV 4 stroke • Twin cylinders • 356L/min FAD • Filter/regulator
3hp Triple Cast IronPortable Air Compressor• 150psi • Filter/regulator • 60lt tank • 15amp/240volt • FAD 309L/min
3 YEARPUMP
WARRANTY
3 YEARPUMP
WARRANTY
5.5hp 200lt Tank• Belt drive v-twin • 150psi • 10amp/415volt• Disp 627L/min • FAD 482L/min
10hp 270lt Tank• Belt drive • 150psi • 18amp/415volt• Disp 1488L/min • FAD 1085L/min
XRS35pictured
7.5hp 270lt Tank• Belt drive • 150psi • 15amp/415volt• Disp 1076L/min • FAD 704L/min
3 YEARPUMP
WARRANTY
ELECTRIC STATIONARY AIRCOMPRESSORS
Triple Cast Iron Portable Air Compressor• Belt drive• 309L/min FAD• 150psi• 100lt tank• 240volts/15amp• Filter/regulator
3 YEARPUMP
WARRANTY
3 YEARPUMP
WARRANTY
AAUUSSTTRRAALLIIAA’’SS CCOOMMPPLLEETTEE RRAANNGGEE OOFF
Subscribe to our channel: sptools
XRS25$1895
XRS35$2585
XRS50$2985
XRS1800$1190
1.5hp Direct Drive AirCompressor• Direct drive • 125psi pressure • Regulator • 6lt tank • 10amp/240volt • 125L/min P/Disp • FAD 52L/min
SS65$119
XRV1760P$1389
XRS18$995
XRV14$699
XRV17$799
Austech Industries 2012 ©COPYRIGHT 11
6.5hp Portable Air Compressor• 6.5hp Torini engine • Belt drive • 150psi • 60lt tank • OHV 4 stroke • Twin cylinders • 356L/min FAD • Filter/regulator
2.5hp Portable AirCompressor• Direct drive • 150psi • Filter/regulator • 50lt tank• 10amp/240volt • FAD 170L/min
SP AIRINDUSTRIALWARRANTY
3 YEAR
2.2hp Cast Iron V-Twin Portable AirCompressor• 150psi • Filter/regular • 50lt tank • Fad 186L/min
SP AIRINDUSTRIALWARRANTY
3 YEAR
2hp Trade Duty Portable AirCompressor• Direct drive • 120psi • Regulator • 10lt tank • 10amp/240volt• FAD 127L/min
SP AIRINDUSTRIALWARRANTY
3 YEAR
2hp Portable AirCompressor• Direct drive • 120psi • Filter/regulator • 36lt tank • 10amp/240volt • FAD 127L/min
SP AIRINDUSTRIALWARRANTY
3 YEAR
Construction Series Stapler• Uses 22 gauge staples with 9mm crown• Load capacity 180pcs 6-16mm
SP AIRINDUSTRIALWARRANTY
3 YEAR
Construction Series Stapler• Uses 21 gauge staples with 12.7mm crown• Load capacity 150pcs 6-16mm
SP AIRINDUSTRIALWARRANTY
3 YEAR
Construction Series Stapler• Uses 18 gauge staples with 5.7mm crown
• Load capacity 100pcs 16-40mm
SP AIRINDUSTRIALWARRANTY
3 YEAR
Construction Series C Bradder• Uses 16 gauge C brads• Load capacity 80pcs 20-50mm
SP AIRINDUSTRIALWARRANTY
3 YEAR
Construction Series C1 Bradder• Uses 18 gauge C1 brads• Load capacity 100pcs 20-50mm
SP AIRINDUSTRIALWARRANTY
3 YEAR
Construction SeriesFraming Gun• Cast magnesium/alum body• Load capacity 80pcs
Construction Series Coil Nailer• Drives standard coil wire/plastic sheet collation nails from 1-12” to 2-1/2” x .090 to .099
ConstructionSeries FlooringStapler/Nailer• 15-1/2 Ga 92pc staples and 16Ga 100pc “L” cleat load capacity
AUSTRALIA’S COMPLETE RANGE OF IINNDDUUSSTTRRIIAALL AAIIRR CCOOMMPPRREESSSSOORRSS
SP AIRINDUSTRIALWARRANTY
3 YEAR
SP AIRINDUSTRIALWARRANTY
3 YEAR
SP AIRINDUSTRIALWARRANTY
3 YEAR
Follow us @sptoolsracing
Construction Series Angle FinishNailer• Uses 15Ga angle finish nails from 1-1/4”to 2-1/2”
SP AIRINDUSTRIALWARRANTY
3 YEAR
SP12-50$499
SP13-50$649
SP11-40$395
SP11-10$299
SP-9200$239
SP-9665$299
SP-9350$239
SP-9225$99
SP-9190$199
SP-9180$59
SP-9171$79
SP-9215$99
$185SP-9255
12 Austech Industries 2012 ©COPYRIGHT
9pc Metric 15O OffsetReversible GeardriveSpanner Set • 8, 10, 12, 13, 14, 15, 17, 18 & 19mm
8pc SAE 15O OffsetReversible GeardriveSpanner Set• 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16 & 3/4"
11pc Stubby Metric15O OffsetReversibleGeardrive Spanner Set• 8, 10, 11, 12, 13,14, 15, 16, 17, 18 & 19mm
8pc Metric 15O Offset ReversibleGeardrive Spanner Set• 20, 21, 22, 24, 26, 27, 30 & 32mm
7pc SAE 15O
OffsetReversibleGeardriveSpanner Set• 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8 & 1-1/4”
®
®
12pc Metric 15O Reversible SpeeddriveCombination Geardrive Spanner Set • 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18 & 19mm
8pc SAE 15O
ReversibleSpeeddriveCombinationGeardrive Spanner Set • 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16 & 3/4”
®
4pc SAE 15O Offset DoubleRing Geardrive Spanner Set • 5/16x3/8, 7/16x1/2, 9/16x5/8 & 11/16x3/4”
GGEEAARRDDRRIIVVEE SSPPAANNNNEERRSSSP Geardrive Spanners are precisely machined, heat treated and tested under thestrictest quality control measures to ensure durability. The reverse switch allowsforward or reverse movement of the ratchet without removing the spanner from the fastener allowing faster and more efficient usage. The open end allows you to keep it on the fastener without removing the spanner.
8pc Stubby SAE 15O OffsetReversible GeardriveSpanner Set• 5/16, 3/8, 7/16, 1/2, 9/16, 5/8,11/16 & 3/4"
®
®
WORLDCLASSQUALITY
www.facebook.com/sptoolsracing
SP10118$299
SP10167$249
SP10169$169
SP10139$189
SP10188$149
SP10131$149
SP10158$199
SP10109$149
SP10454$115
6pc Metric 15O Offset DoubleRing Geardrive Spanner Set • 8x9, 10x11, 12x13, 14x15, 16x18 & 17x19mm
SP10406$165
Austech Industries 2012 ©COPYRIGHT 13
11pc Flexhead Metric Geardrive Spanner Set• 8, 10, 11, 12, 13, 14, 15, 16, 17, 18 & 19mm
8pc Flexhead SAEGeardriveSpanner Set • 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16 & 3/4"
®
14pc Stubby Flexhead MetricGeardrive Spanner Set• 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18 & 19mm
®
8pc Flexhead Metric GeardriveSpanner Set • 20, 21, 22, 24, 26, 27, 30 & 32mm
7pc Flexhead SAE GeardriveSpanner Set • 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8 & 1-1/4”
8pc SAE 0O
SpeeddriveCombinationGeardrive Spanner Set• 5/16, 3/8”, 7/16, 1/2, 9/16, 5/8, 11/16 & 3/4”
®
12pc Metric 0O Speeddrive Combination Geardrive Spanner Set • 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18 & 19mm
12pc Metric Extra Long Double RingGeardrive Spanner Set • 8, 9, 10, 12, 13, 14, 15, 16, 17, 18 & 19mm
8pc SAE Extra Long Double RingGeardrive Spanner Set• 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16 & 3/4”
®
GEARDRIVE SPANNERS WWOORRLLDD CCLLAASSSS QQUUAALLIITTYY && DDUURRAABBIILLIITTYY
HEATTREATED FORDURABILITY
Subscribe to our channel: sptools
SP geardrive spanners are fitted witha 72 teeth mechanism allowing only 5 degree movement, great for tight confined areas.
SP10412$269
SP10468$189
SP10311$249
SP10358$179
SP10334$165
9pc Stubby Flexhead SAEGeardrive Spanner Set• 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16 & 3/4"
SP10389$129
SP10367
$259SP10318
$259
SP10272$139
SP10222$169
14 Austech Industries 2012 ©COPYRIGHT
14pc Metric Combination Spanner Set • 6-19mm
13pc SAE Combination Spanner Set• 1/4-1”
18pc Metric/SAE Spanner Set • Metric – 8, 10, 11, 12, 13, 14, 15, 16, 17 & 19mm
• SAE – 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, 3/4” & 7/8"
6pc Metric 15O Offset Long Ring Spanner Set• 8x10, 12x14, 13x15, 16x18, 17x19 & 22x24mm
4pc SAE 15O Offset Ring Spanner Set• 3/8x5/16”, 1/2x7/16”, 5/8x9/16” & 3/4x11/16”
®
9pc SAE JumboCombinationSpanner Set• 3/4-1-1/2"
9pc MetricJumboCombinationSpanner Set• 19-36mm
®
5pc Metric 0O Offset LongRing Spanner Set• 8 x 10, 12 x 14, 16 x 18, 17 x 19, 22 x 24mm
4pc SAE 0O Offset Long Ring Spanner Set• 3/8 x 5/16”, 1/2 x 7/16”, 5/8 x 9/16” & 3/4 x 11/16”
®
®
®
DDUUAALL FFLLAATT DDRRIIVVEE SSPPAANNNNEERRSS
Follow us @sptoolsracing
SP10236$199
SP10284$159
SP10035$149
$149SP10084
SP10019$249
SP10069$249SP10063
$99
SP10014$99
SP10001$159
Austech Industries 2012 ©COPYRIGHT 15
23pc 1/4” Dr 6ptMetric/Sae SocketSet• 1/4" dr 6pt Sockets 4-13mm, 3/16-1/2”
• 1/4" dr 145mm flex handle
• 1/4" dr 45T ratchet handle
• 1/4" dr 50 & 150mm extension bars
®
6pt12pt
32pc 3/8” Dr12pt Metric/SAESocket Set• 3/8" dr 12pt sockets
• 3/8” dr spark plug sockets
• 3/8" dr accessories
12pt
®
43pc 1/4” Dr 12 &6pt Metric/SAESocket Set• 4-13mm & 3/16 -1/2" sockets
• 145mm flex handle • 72T ratchet handle • 50mm & 150mm extension bars
• Universal joint
®
6pt12pt
®
51pc 3/8” Dr 12 & 6ptMetric/SAE Socket Set • 6-22mm & 1/4-7/8" sockets
• 10-19mm & 3/8-3/4" deep sockets
• 72T rotatable ratchet handle
• 45T ratchet handle • 200mm flex handle • 75mm & 250mm extension bars
®
41pc 1/2” Dr 12pt Metric/SAE Socket Set • 10-32mm & 3/8-1 1/4” 12pt sockets
• Spark plug sockets • 250mm flex handle • 45T ratchet handle • 125 & 250mm extension bars
• Universal 12pt
59pc1/4"-3/8"-1/2"Dr 12ptMetric/SAESocketSet• 1/4 3/8 & 1/2dr 12pt metric & SAE sockets
• 3/8dr metric & SAE Inhex bit sockets • 1/4, 3/8 & 1/2dr 45T ratchets • 1/2dr flex handle • 1/4, 3/8 & 1/2dr wobble extension bars
32pc 3/4” Dr 12pt Metric/SAE Socket Set• 12pt metric & SAE sockets
• 450mm flex handle • 24T ratchet handle • 200mm & 400mm extension bars
• Universal joint • Extendible handle
®
12pt
70pc 1/4”, 3/8”& 1/2” Dr MetricMotorsportSocket Set• 1/4", 3/8” & 1/2" dr curved motorsport ratchets
• 1/4" & 3/8” dr sliding T-bar
• 1/2" dr flex handle
• 1/4", 3/8” & 1/2" dr wobble extensions
®
SSPP SSOOCCKKEETT SSEETTSS
6pt12pt
NEW
12pt
www.facebook.com/sptoolsracing
SP20280$199SP20102
$59
SP20101$139
SP20300$149
SP20200$89
SP20400$499
SP20201$199
SP20610$259
3/8” Dr Oxygen Sensor Socket• 3/8"dr x 22mm x 90mm long• Window in socket allows the wires attached to thesensors to be bypassed
• Applications include Mitsubishi, Nissan, GM,and the Volkswagon Audi Group
• For heated & non-heated lambda sensors
Spark Plug Installation/Removal Tool• Fits on most common sizes of spark plugs
• Flexible rubber shaft allows access in confined areas
• Reduces possible cross threading on deep seated engine applications
7pc Sensor Socket Set• Includes 29mm pressure/vacuum switch socket, 7/8" vacuum switch socket, 27mm oil pressure sending unit socket, 1" & 1-1/16" oil pressure sending unit socket, long oxygen sensor socket & short oxygen sensor socket
• Window in socket allows the wires attached to the sensors to be bypassed
• Applications include Mitsubishi, Nissan, GM,and the Volkswagon Audi Group
• For heated & non-heated lambda sensors
Camshaft Pulley Remover/Installation Kit• Designed to hold the camshaft pulley stationary while loosening & tightening the centre shaft bolt
• Fixed distance 54 - 120mm
16 Austech Industries 2012 ©COPYRIGHT
Oil EvacuationSystem• Portable fluid extraction unit
• Brake fluid reservoir refiller• Brake bleed bottle
Manual Brake Bleeder Kit
Subscribe to our channel: sptools
6pc Belt Tensioner Serpentine Tool Set• Contains 3/8”dr sockets 13, 15, 16 & 18mm• Essential tool for removing & installing timing belts with spring loaded idler pulleys
• Long reach design with multi-positional extensionallows access deep into the engine compartment & around obstructions
NEW
NEW NEW
NEW
SP71055$4995
SP64065$99
6pc Belt Tension Locking Pins Set• Includes 0.79mm, 1.24mm, 1.37mm, 1.49mm, 1.68mm & 1.92mm
• Suitable for locking back belt tension devices while installing or removing cam or auxiliary drive belt
• Wide range of vehicle & engine applications
SP71060$1795NEW
SP64060$1350
SP71065$69
SP64047$1080
SP70890$189
SP70858$69
SSPP SSPPEECCIIAALLTTYY TTOOOOLLSS FFOORR YYOOUURR
NEW
5pc Master Cam Clamp Kit • Master kit contains the dual CamClamp and CamClamp singles for dual or quad overhead cam engines
• Single CamClamps lock gears individually
Valve Spring Compressor• Reversible jaw adapter for multi-valve engines• Large throat clearance for larger engines• Dual size 25mm x 30mm collet release adaptors• Unique direct action compressor lever givesimproved visibility & ease of difficult access
Austech Industries 2012 ©COPYRIGHT 17
500ml Vacuum Brake Bleeder Kit • Automatically bleed brakes and refill the fluid reservoir
• 500ml brake bleeder which fits easily in the wheel area
• Brake fluid reservoir refiller
Test Vac Vacuum Test Kit• The complete kit for all vacuum testing and brake bleeding requirements
• Brass piston bore to resist corrosion
Deluxe Cooling SystemPressure Tester• Eliminates the need for adapters to pressure test the cooling system
• Suits automotive, commercial, heavy duty, marine and motorcycle applications
• Includes 6 double end radiator cap testers
www.facebook.com/sptoolsracing
Unique Compression Tester• Easy reading 2-1/2" dia gauge features colour coated quadruple calibrations 0-300psi, 21kg/cm,21bar & 2100kpa
• 13" durable rubber hose with 14mm/18mm adapter
• 6" heavy-duty stem with universal rubber• Cone adapter fits all plug holes
2pc Valve Lappers• Small cup diameters 5/8" & 13/16"• Large cup diameters 1-1/8" & 1-3/8"• Hand grind small & large flat-head unslottedvalves
• To use place grinding compound on valve faceand put in seat
Angled Type Universal Hose Clamp Plier Set• Set of pliers with interchangeabletips to cover all types of hoseclamps
Straight Type Universal Hose Clamp PlierSet• Set of pliers with interchangeabletips to cover all types of hoseclamps
NEW
NEW NEW
NEW
NEW
NEW
SP72610$4490
SP72620$4490
Screw Type Overhead Valve Spring Compressor• Easily remove valve springs on most cars &light trucks
• Works with cylinder head on or off the engine
• The jaws grip the valve spring in parallelcompression
SP66012$58
SP66015$87
SP66115$1165
SP66024$69
SP70889$325
SP80000$119
SP70856$159
SP70900$99
WWOORRKKSSHHOOPP
Brake Piston Rewind Kit• Right or left hand• Suitable for push-back & wind-back brake pistons• Includes both left & right handed thrust bolt assemblies
• Helps prevent damage to pistons & seals
Master Pulley Set• Includes two/three way yoke, 4pc tips, metric & SAE bolt sets & 2pc centre screw for puller
• Master bolt grip Sset works on harmonic balancers, steering wheels, crankshaft pullers & gears
42pc Automotive Rethreading Kit• Taps & dies are suitable for chasing out damaged threads and the removal of nicks/burrs without undercutting good threads
• Thread file restores damaged external threads on any diameter
• Right or left hand
CV Band Pliers• Offset cutter designed for easy removal of stainless steel CV joint clips andhose clamps without damaging the boot or hose
• Profiled jaws prevent band slipping while being cut
Oil Filter Wrench• Truck strap type• Satin finish cast steel body with 3/8" & 1/2" square drives
• Designed to be used with a ratchet wrench or 21mm (13/16") spanner
• Extra wide nylon webbing strap• 300mm capacity diameter
18 Austech Industries 2012 ©COPYRIGHT
4pc Small Line Clamp Set• Seals flexible brake and fuel lines from 3mm to 8mm
4pc Hook & Pick Set• Awl tool, 45 degree tool,90 degree tool &hook tool
®
4.5kg Magnetic Pick-Up Tool
6.8kg MagneticPick-Up Tool
®
Crankshaft Bolt Removal Tool• Reduces service time on vehicles with limited crankshaft bolt access
• For Honda crankshaft bolt removal• Generates up to 600 ft/lbs of force which exceeds most 1/2" dr impact guns
• Bi-directional force loosens or tightens bolts
Folding Lock-BackUtility Knife• Includes spare blades
®
®
Follow us @sptoolsracing
NEW
NEWNEW
NEW
NEWCV Boot Clamp Banding Tool• For installing band style clamps that require the tensions to be maintained while the band is locked into place
• Built in cutter & winding mechanism allows banding to be tightened and cut quickly
NEW
SP67150$33
SP31512$22
SP31513$22
SP30850$15
SP70865$149
SP30802$12
Multi-Purpose Cleaning Gun• Delivers high pressure – high flow cleaning in the palm of your hand
• Integrated air and water controls for easy use• Multi-step nozzle fits most heater and radiator hoses for system flushing
SP70801$59
SP70718$34
SP67160$5950
SP67038$124
SP63005$12750
SP31310$158
SP64012$3499
SSPP SSPPEECCIIAALLTTYY TTOOOOLLSS FFOORR YYOOUURR
Universal Ball Joint Seperator• 18-24mm jaw capacity• 30-50mm working area pusher• This tool is used to separate the ball joint from the spindle support arm
• It works on most of vehicles• Adjustable from 20mm to 50mm
Mini Ball Joint Seperator• Chrome-plated finish drop forged steel bodywith thrust bolt
• Suitable for most small cars and light vans
Steering Wheel Puller Set• Two-leg puller with two pairs of legs & two thrust caps
• Includes yoke, thrust bolt
• For use on GM & Ford vehicles
Macpherson strut Spring Compressor• Allows you to compress the external coil springs on conventional MacPherson style struts to replace shock absorbers, spring sets, repair bent struts and damaged spindles
• Works on and off your car
Subscribe to our channel: sptoolsAustech Industries 2012 ©COPYRIGHT 19
3 Prong OilFilter Wrench
Oil FilterWrench
8m x 25mm Metric Tape Measure• Tough impact resistant ABS case with soft protective grip
• Three trigger switches (side, bottom and front) to make sure the blade can be locked under any circumstances
®®
Stainless Steel Rulers
MODEL SIZE PRICESP35211 150mm/6” $4SP35213 300mm/12” $9SP35215 600mm/24” $19SP35217 1000mm/40” $29
Oil Filter Wrench • 6-8cyl Toyota/Lexus
Oil Filter Wrench• 4cyl Toyota/Lexus
Hub ClampExpander• Allows easy removal and installation of struts and ball joints
• Adjustable for use on hubs with centralized or non centralized slot
NEW NEW
NEW
NEW
NEW
Nylon Strap Oil Filter Wrench• Suits oil filters up to 150mm• 1/2” square drive
SP67025$62
NEW
SP64008$19
SP64010$19
SP64000$19
SP35200$995
SP67027$11495
SP70970$130
SP67040$7650 SP67022
$2650
SP67023$4750
SP71113$39
SP71110$39
WWOORRKKSSHHOOPP
Coil Spring Compressor• This coil spring compressor uses twin prongs &works at a pressure up to 1100kgs• Wrap over coil claws for extra safety• Max. jaw opening 230mm• Carbon steel, hardened lead screws & cast jaws• Suitable for use where space under wheel arch is limited
20 Austech Industries 2012 ©COPYRIGHT
12pc ScrewdriverSet in Plastic Case• 6 x slotted screwdrivers
• 6 x phillips screwdrivers
® ®
12pc Screwdriver Set in Metal Case• 6 x slotted screwdrivers
• 6 x phillips screwdrivers
10pc Electrical Screwdriver Setin Metal Case• 6 x slotted & 4 x phillips electrical screwdrivers
13pc Impact Driver Set• Impact driver • 4 x slotted bits - 5, 6, 8 & 9mm • 4 x phillips bits - #1, #2, #3 & #4 • 4 x inhex bits - 4, 5, 6 & 8mm
®
®
67pc 1/4”dr Power Bit Set• Includes hexagon, phillips, pozidrive, square slotted, spanner, torx star, tamper torx, torx plus, spline bits and holder bits
10pc 1/2” Dr Heavy Duty Impact Driver Set• 4 x phillips bits • 4 x slotted bits • Impact handle• Bit holder has 1/2" & 5/16" hex for phillips and slotted bits
®
37pc 3/8” & 1/2”dr Professional Bit Set• 6 x hexagon 300mm(L) bits • x spline 300mm(L) bits• 12 x torx 300mm(L) bits• 10 x ribe 300mm(L) bits• 1 x 100mm extension bit holder
• 3/8” & 1/2” dr bit adaptor
® 11pc 6mm Hex Dr Half FlexibleHose Clip Bit Driver Set• PH1, PH2, PZ1, PZ2, SL4, SL5, T20, T25, T30 & T40
NEW6pc 1/4” Dr Half Flexible
Hose Clip Nut Driver• 5, 6, 7, 8, 10mm sockets
9pc Metric Magdrive Hex Key Set• 1.5, 2, 2.5, 3, 4, 5, 6, 8 & 10mm
9pc Torx Magdrive Hex Key Set• T-10, T-15, T-20, T-25,
T-27, T-30, T-40, T-45 & T-50
®
9pc SAE Magdrive Hex Key Set• 1/16”, 5/64”, 3/32”, 1/8”, 5/32”, 3/16”, 1/4”, 5/16” & 3/8”
13pc Metric Long ArmHex Key Set• 2, 2.5, 3, 4, 5, 6, 7, 8, 10, 12, 14, 17 & 19mm (2mm without magnetic)
®
13pc SAE Long Arm Hex Key Set
• 5/64”, 3/32”, 1/8”,5/32”, 3/16”, 7/32”, 1/4",5/16”, 3/8”, 1/2", 9/16”,
5/8” & 3/4" (5/64”without magnetic
®
SSPP SSCCRREEWWDDRRIIVVEERRSS -- HHEEXX KKEEYYSS -- BBIITTSS
www.facebook.com/sptoolsracing
SP34512$39
SP34511$39
SP34517$39 SP34526
$79 SP34527$79
SP34035$49
SP30861$25
SP30862$25
SP39510$45
SP34000$39
SP34012$79
SP34040$89
SP39610$69
SP34030$39
3pc Long Handle Plier Set• Straight, 45 degree & 90 degree bent long handle pliers
Austech Industries 2012 ©COPYRIGHT 21
3pc 200mm Plier/Cutter Set• Includes high leverage combination pliers, long nose pliers and diagonal cutters
®
3pc 250mm Locking Plier Set• Curved jaw, straight jaw & long nose
®
16oz (1lb) Dead Blow Hammer
48oz (3lb) DeadBlow Hammer
®
16oz Moulded Handle BallPein Hammer
32oz MouldedHandle Ball Pein
Hammer
®
10pc Pin Punch & Chisel Set• 2, 3, 4, 5, 6, 8 & 10mm pin punches• 12, 20 & 24mm chisels ®
PitmanArmPuller
®
®
Pulley Puller• For removing alternator & power steering pulleys
HarmonicBalancerPuller• Yoke designed for 2/3/4 hole applications
• Suitable for harmonic balances, flywheels
• Gears & pulleys with tapered holes
• Include 5/16” & 3/8” M8 bolts
SP SCREWDRIVERS - HEX KEYS - BITS
Follow us @sptoolsracing
SP30216$19
SP30232$2432oz (2lb) DeadBlow Hammer
SP30248$27
SP67037$27
SP30166$28
SP30174$33
24oz Moulded Handle Ball Pein Hammer
SP30182$39
SP67030$19
SP67035$19
SP32905$99
SP32926$69
SP30841$69
SP32903$99
®
SSPP PPRROOFFEESSSSIIOONNAALL TTOOOOLLSS
22 Austech Industries 2012 ©COPYRIGHT
ProtectiveMechanics SeatCover• Heavy duty nylon
Mechanics MagneticMudguard Protector• Vinyl with soft inner to protect car paintwork
Heavy Duty Shop Seat• Heavy duty polished chrome frame
Pneumatic Shop Stool• Pneumatic seat adjusts from 420mm to 533mm
Fingerless GlovesSP MechanicGloves
MODEL SIZE PRICESP68891 Large $59SP68892 X-Large $59
MODEL SIZE PRICESP68861 Medium $19SP68862 Large $19SP68863 X-Large $19
MODEL SIZE PRICESP68887 Medium $29SP68888 Large $29SP68889 X-Large $29
MODEL SIZE PRICESP68874 Medium $24.90SP68875 Large $24.90SP68876 X-Large $24.90
“Kevlar” HeatGloves
Utility Gloves
NEWNEW
NEW
SSPP FFOORR TTHHEE WWOORRKKSSHHOOPP
PneumaticSwivel Stool• Pneumatic seat adjusts from 660mm to 787mm
Mechanics Creeper• 6 heavy duty wheels
• 1030mm x 440mm
www.facebook.com/sptoolsracing
SPR-22$29
SPR-44$59
SPR-55$129
SPR-60$129
SPR-50$119
SPR-11$19
7 DrawerCustom Series Tool Cabinet• 680w x 460d x 775h (with castors 940h)
Austech Industries 2012 ©COPYRIGHT 23
1860mm
(not including handles)745mm
1176mm
20 Drawer 1960w x745d x 1176h SteelRoller Cabinet• 8 x small drawers 370w x 675d x 79h
• 3 x small deep drawers 370w x 675d x 107h
• 1 x small x-deep drawer 370w x 675d x 163h
• 1 x small xx-deep drawer 370w x 675d x 275h
• 3 x large drawers 775w x 675d x 79h
• 2 x large deep drawers775w x 675d x 107h
• 1 x large x-deep drawer 775w x 675d x 163h
• 1 x X-large drawer 1229w x 675d x 123h
2.3TON TOOLSTORAGECAPACITY
245LTSTORAGECAPACITY
2000mm Custom Series Workshop Bench• 3 x lockable drawers 345w x 430d x 120h
• Combination stainless steel/ rubber worktop
• Lockable drawers • Can be bolted to floor
2 TONNELOAD
CAPACITY
11 Drawer Custom Series Tool Cabinet• 1180w (inc handle) x 480d x 1070h (inc castors) 400LT
STORAGECAPACITY
®
®
www.facebook.com/sptoolsracing
SP 2012Car ToolBoxSticker
SP 2012 Girl ToolBox Sticker
2pc Sticker Pack toSuit Concept SeriesBoxes
2pc Sticker Packto Suit ConceptSeries Boxes
SP40104$469
SP40106$995
SP40400$595
SP40080
$4495
®
SSPP PPRREEMMIIUUMM SSTTOORRAAGGEE && SSTTIICCKKEERRSS
SPS5$100
NEW
NEWNEW
NEW
NEWSPS1$10
SPS2$20
SP 2012 RacingSticker
SPS3$20
2 Drawer Custom Series Steel ToolTrolley• 900w x 490d x 770h (890h with castors) • 2x large drawers 620w x 405d x 55h, 30 litre storage capacity
• Bottom tray area 760mm x 485mm x 345mm, 154 litre storage capacity
®
18 Drawer Storage Box• 826w x 300d x 305h • Drawers 118w x 286d x 60h
CAN BE USED
FOR PARTS STORAGE
IN WORKSHOPS OR
MOBILE SERVICE
VEHICLES! PARTS BINS
LOCK INTO OUTER
STEEL FRAME!
®
SP40568$199SP40107
$299
SPS6$100
24 Austech Industries 2012 ©COPYRIGHT
512pc Sumo Tool Kit• Sumo roller cabinet• 1/4", 3/8" and 1/2" dr sockets & accessories• Impact sockets & screwdrivers• Spanners - ROE, ring, flare & geardrive• Pliers - cutters and circlip pliers• Hammers - hacksaws - tape measure• Garage creeper • Automotive speciality tools • Air tools - ratchets & impact wrench • SP official merchandise
231pc Metric/SAE Tool Kit inHyper Blue Top/Bottom Box• All sockets, socket accessories & ROE spanners come in hi-density foam storage system
• 1/4", 3/8", 1/2" dr sockets & accessories• Screwdrivers and hex keys
• Bit set• Pliers and cutters• Adjustable wrench &hammer• 7 drawer concept tool box• 7 drawer roller cabinet
®
ALSO AVAILABLE IN ATOMICGREEN MODEL SP50061
ALSO AVAILABLE IN BALISTICORANGE MODEL SP50063
ALSO AVAILABLE IN NITRO RED MODEL SP50060
603pc Metric/SAE Tool Kit inCustom Series Tool Box• 1/4", 3/8” & 1/2”dr sockets and accessories• ROE, stubby ROE and
geardrive spanners• E TORX sockets & spanners• 1/2”dr impact sockets, inhex & TORX bits• Adjustable wrenches• T-handle hex keys & TORX keys• Hammers soft/hard face, ball pein & dead blow• Pliers, cutters & wire
strippers• Hand riveter, ratchet set & burr set• Digital multimeter, work light, filter wrench & metal rulers• Custom series tool box & roller cabinet
®
275pc Metric/SAE Tool Kit in Diamond White Concept
Tool Cabinet• 1/4", 3/8" & 1/2"dr sockets and accessories• Flare spanners Metric& SAE• Screwdriver and hex keys• 2 jaw hand rivetor• Power bit set• Digitalmultimeter • Circuit tester• Combination,
long nose, cutters &snap ringpliers• Hacksaw, folding knife, tweezers & soft face
hammer• 7 drawer white concept tool box• 7 drawer white concept
DIAMOND WHITE
NEWRELEASE
®
AAUUSSTTRRAALLIIAA’’SS LLEEAADDIINNGG RRAANNGGEE OF TOOL KITS
Follow us @sptoolsracing
SP50180$8995
SP50062$1595
SP50165$3950
SP50055$1799
2.3TON TOOL
STORAGECAPACITY
®
Austech Industries 2012 ©COPYRIGHT 25
• ROE spanners• Sockets & accessories
• Screwdrivers• Pliers & cutters• Adjustable wrench• Hex & TORX keys• Hammer • Foldback knife • Pick up tool
• Inspection mirror• Magnetic parts tray• Circuit tester• Multimeter
275pc FieldService Tool KitAll sockets, socketaccessories and ROE
spanners come inhi-density
foam storage system
• Pick set • Tape measure• Screw extractor set • 7 drawer field service box
MobileMobileSolutionsSolutionsMobile
Solutions
240pc Metric/SAE Tool Kit inCustom Series Tool Box• Maxi drawers featuring 405mm depth• ROE combination spanners• Flare metric/SAE spanners• 1/4", 3/8” & 1/2"dr sockets & accessories• Hex keys & screwdrivers
• Pliers & cutters• Hammer, hacksaw &
tape measure• Adjustable wrench• Pry bars & hook and pick sets• 7 drawer steel
tool box®
All sockets, socket accessories and ROE spanners come in hi density foam tool storage system
®
134pc Metric/SAE Tool Kit in Custom Series Tool Box
97LTSTORAGECAPACITY
• Metric & SAE combination spanners• 1/4", 3/8” & 1/2” dr metric & SAE sockets • 1/4, 3/8 & 1/2" 45T ratchets• 1/4, 3/8 & 1/2" flex handles • 3/8” dr 5/8 & 13/16” spark plug sockets
• Adaptors • Screwdrivers • Wobble extension bars• Combination pliers & diagonal cutters• Hex keys • Hammer • Adjustable wrench• 7 drawer tool box
AUSTRALIA’S LEADING RANGE OOFF TTOOOOLL KKIITTSS
All sockets, socketaccessories and ROEspanners come in hi-density foam storage system
Subscribe to our channel: sptools
SP50097$659
SP50102$1100
SP50115$1995
230pc Metric/SAE Tool Kit in AtomicGreen Custom Series Tool Box
• All sockets, socket accessories &ROE spanners come in hi-density
foam storage system• 1/4", 3/8", 1/2" dr sockets & accessories• Screwdrivers and hex keys• Bit set• Pliers and cutters• Adjustable wrench & hammer• 7 drawer concept toolbox
ALSO AVAILABLE IN HYPERBLUE MODEL SP50042
ALSO AVAILABLE IN BALISTICORANGE MODEL SP50043
®
Drawer Locking System
ALSO AVAILABLE IN NITRO RED MODEL SP50040
®
SP50041$998
26 Austech Industries 2012 ©COPYRIGHT
230pc Metric/SAE Tool Kit inCustom Series RollerCabinet• Metric & SAE spanners &sockets• 45T tatchets and flex handles• Wobble extension bars• Spark plug xockets and adapters• Adjustable wrenches• Ball pein hammers• Pliers, circlip pliers &diagonal cutters• Pin punch & chisels• Hex & torx keys• Screwdrivers• Bit set• Hacksaw• Tapemeasure• 6 xdrawertrays
®
Drawer Locking System
®
Drawer Locking System
ALSO AVAILABLE INVOODOO BLUESP52120
275pc Metric/SAE Tool Kit in Diamond White Concept
Tool Cabinet• 1/4", 3/8" & 1/2"dr sockets and accessories• Flare spanners Metric& SAE• Screwdriver and hex keys• 2 jaw hand rivetor• Power bit set• Digitalmultimeter • Circuit tester• Combination,
long nose, cutters &snap ringpliers• Hacksaw, folding knife, tweezers & soft face
hammer• 7 drawer white concept tool box• 7 drawer white concept
DIAMOND WHITE
NEWRELEASE
275pc Metric/SAE Tool Kit in Diamond White Concept
Tool Cabinet• 1/4", 3/8" & 1/2"dr sockets and accessories• Flare spanners Metric & SAE• Screwdriver and hex keys• 2 jaw hand rivetor• Power bit set• Digital multimeter • Circuit tester• Combination, long nose, cutters & snap ring pliers• Hacksaw, folding knife, tweezers & soft face hammer• 7 drawer white concept tool box• 7 drawer white concept roller cabinet
DIAMOND WHITE
NEWRELEASE
• 9 drawer roller cabinet
®
259pc Motorsport Metric/SAETool Kit in Midnight Black• Motorsport 7 drawer “Midnight Black” steel toolbox
• Sockets, socket accessories and motorsport quad drive spanners in EVA foam storage• E-torx set • Screwdrivers
• Magnetic metric & SAE key set • Pliers and cutters • Bit set
• Adjustable wrench• Hammer and tape measure
www.facebook.com/sptoolsracing
SP50604$1495
SP50056$1895
SP50057$1895
SP52130$1495
Austech Industries 2012 ©COPYRIGHT 27
800mmSP TrolleyTool Bag
550mm SP Trolley Tool Bag
Follow us @sptoolsracing
SP Travel BagSP Travel Team Bag
SSPP TTOOOOLL TTRRAAVVEELL RROOLLLLEERR BBAAGGSS
Large range of individual sockets available - see in store for details
THE BEST IMPACT WRENCHES NEED THE BEST IMPACT SOCKETS
ADAPTORSEXTENSION BARS
MODEL SIZE PRICESP23355 1/2F x 3/8M $9SP23356 1/2F x 3/4M $13SP24355 3/4F x 1/2M $18SP24356 3/4F x 1M $22
MODEL SIZE PRICESP22346 3/8” Dr, 150mm $10SP22345 3/8” Dr, 75mm $10SP23346 1/2” Dr, 150mm $12SP23347 1/2” Dr, 250mm $21SP24346 3/4” Dr, 150mm $40
MODEL SIZE PRICESP24347 3/4” Dr, 250mm $46SP24348 3/4” Dr, 330mm $56SP25346 1” Dr, 175mm $65SP25347 1” Dr, 250mm $69SP24348 1” Dr, 330mm $95
MODEL SIZE PRICESP23350 1/2” Dr $17SP24350 3/4” Dr $59
UNIVERSAL JOINTS®
SPTB$189
SPTBRACE$249
NEW
NEW
Bag pocket
Shoe compartmentWheels
(Shirt and shoesnot included)
SP40365$59
SP40366$89
Our LARGE TRAVELROLLER BAGS are sovisually outstandingyou will never havetrouble finding yourbag again. This worldtraveler comes with atelescoping handle,smooth rollingwheels and threestrategically placedgrip handles for easymanoeuvrability. It’sbig and brawny withdurable polyester andheaps of storagespace. Other featuresinclude a lockablezipper pull, 3 exteriorquick access pockets,and an interior meshpocket with a zip.• Size: 800mm H (without handle extended) x 410mm W x 330mmD
NEW
3/8” Dr INDUSTRIAL Mini Impact Wrench• 12v platform • No-Load Speed: 2200rpm• Torque: 105N-m• Charging Time: 1 hour auto cut-off• 2 year warranty (Battery 1 year)• Protective blow mould case
Hydraulic Puller Kit• Master set of gear pullers and bearing separators packed into a carry case
• 10 tonne hydraulic ram compatible with other sets in the range
28 Austech Industries 2012 ©COPYRIGHT
®
Air Duster• Brass thread air inlet
BONUS CAP
Motorsport 9pc T-Handle Socket Set• 8, 9, 10 and 11mm (130mmW x 300mmH) t-handle sockets
• 12, 13, 14, 17 & 19mm (200mmW x 300mmH) t-handle sockets
All prices include GST. Not all products in this brochure are available from alloutlets. Prices may vary in some country areas due to freight costs. All products inthis brochure were available at the time of printing. Austech Industries will doeverything possible within reason, to maintain stocks of products advertised butcannot be responsible for unforeseen shortfalls beyond their control. E & OCopyright. www.sphandtools.com
I N D U S T R I E S
Austech
NEW
SP 10pc (4 Tools) 18v Power Tool KitContents:• SP81126 250Nm impact wrench• SP81308BU angle grinder• SP81232BU high torque drill/driver• SP81424BU LED flashlight• Battery charger and batteries
NEW
SP-111$1250
SP81112$279
SP20800$129
SP Open Mouth Bag• Moulded waterproof base
SP40360$59
Slide Hammer Puller Kit• External & Internal 2 & 3 jaw pullers, grip wrench adaptor, lip puller, hub puller & dent puller
• 2.5kg slide hammer with 570mm shaft
SP67048$14995
SP67052$295
242pc Motorsport Metric/SAE ToolKit in Diamond White Concept ToolBox• ROE combination spanners• Flare metric/SAE spanners• 1/4", 3/8" & 1/2"dr sockets & accessories• Hex Keys & screwdrivers
• Pliers & cutters• Hammer, hacksaw & tape
measure• Adjustable wrench• Pry bars & hook and pick sets• 7 drawer white concepttool box
NEW
Batteries
2 x 1.5Ah
SP52250$1195
DIAMOND WHITE
NEWRELEASE
BONUS CAP
Batteries
3 x 3.0Ah
SP82230$1175
NEW