SP SERIES - John Brooks Company · 2018. 5. 17. · SP SERIES FINISH THOMPSON PUMPING SOLUTIONS...
2
SP SERIES FINISH THOMPSON PUMPING SOLUTIONS AROUND THE WORLD MODEL SP22 finishthompson.com Notes: Performance curves above are based on flooded suction. *Performance will vary with suction lift conditions. For performance at various suction lifts, see curve book on FTI web site (www.finishthompson.com) or contact factory. Maximum power @ 3450 RPM is 13 hp (9.7 kW). [Consult factory for applications above 10 hp (7.5 kW)]. At 2900 RPM, maximum power is 7.5 kW (10 hp). Warning! SP Series not recommended for pumping flammables! FEATURES & CAPABILITIES + Self-priming, magnetic drive + Five-year warranty + Provides up to 25 ft. (7.6 m) lift or equivalent + Primes 15 ft. (4.57 m) in 90 seconds with maximum diameter impeller at 60 Hz with 3” pipe + Retains fluid for re-priming when shut off without a check valve + Extended run dry ability (with carbon bushing) + High operating efficiency + Polypropylene or PVDF construction + Powerful neodymium magnets + Close-coupled design + Threaded (NPT or BSP), union or flange connections + Impeller trims available every 1/8” (.32 cm) between smallest and largest diameter + Back pullout design + Mounts to NEMA and IEC (B5 & B14) motor frames + Easy set measurement free drive + ISO 1940 G2.5 balancing + CE certified + High working pressure up to 90 psi (6.2 bar) + Specific gravity up to 1.8 + Polypropylene—180 o F (82 o C) + PVDF—220 o F (104 o C) APPLICATIONS + Rail cars & tanker trucks + Tanks with an opening on top + Sumps and reservoirs + Below grade storage tanks + Over-the-wall applications + When run-dry protection is needed + and many more! 0 20 40 60 80 100 120 140 160 180 0 25 50 75 100 125 150 175 200 225 250 275 FLOW (US gpm) NPSHR (ft) 0 10 20 30 40 50 0 5 10 15 20 25 30 35 40 45 50 55 60 FLOW (m/hr) 3 #1 #2 #3 #4 #5 Curve Legend #1- 7.00" (177.8 mm) #2- 6.50" (165.1 mm) #3- 6.00" (152.4 mm) #4- 5.50" (139.7 mm) #5- 5.00" (127.0 mm) 13 BHP 10 BHP 7.5 BHP 5 BHP 3 BHP 45% 40% 35% 20% 48% 10% Minimum Continuous Flow 10 US gpm (2.3 m 3 /hr) 30% NPSHR HEAD (ft) HEAD (m) NPSHR (m) 0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40 45 50 Curve Legend #1- 7.00" (177.8 mm) #2- 6.50" (165.1 mm) #3- 6.00" (152.4 mm) #4- 5.50" (139.7 mm) #5- 5.00" (127.0 mm) #1 #2 #3 #4 #5 40% 35% 20% 43% 10% 30% 5.5 kW 4.0 kW 3.0 kW 2.2 kW 1.5 kW Minimum Continuous Flow 2.3 m 3 /hr NPSHR FLOW (m 3 /hr) NPSHR (m) HEAD (m) SP22 PERFORMANCE Flooded Suction 3450 RPM * SP22 PERFORMANCE Flooded Suction 2900 RPM *
Transcript of SP SERIES - John Brooks Company · 2018. 5. 17. · SP SERIES FINISH THOMPSON PUMPING SOLUTIONS...
SP SERIES
FINISH THOMPSON PUMPING SOLUTIONS AROUND THE WORLD
MODEL SP22
finishthompson.com
Notes: Performance curves above are based on flooded suction.
*Performance will vary with suction lift conditions. For performance at various suction lifts, see curve book on FTI web site (www.finishthompson.com) or contact factory.
Maximum power @ 3450 RPM is 13 hp (9.7 kW). [Consult factory for applications above 10 hp (7.5 kW)]. At 2900 RPM, maximum power is 7.5 kW (10 hp).
Warning! SP Series not recommended for pumping flammables!
FEATURES & CAPABILITIES
+ Self-priming, magnetic drive
+ Five-year warranty
+ Provides up to 25 ft. (7.6 m) lift or equivalent
+ Primes 15 ft. (4.57 m) in 90 seconds with maximum diameter impeller at 60 Hz with 3” pipe
+ Retains fluid for re-priming when shut off without a check valve
+ Extended run dry ability (with carbon bushing)
+ High operating efficiency
+ Polypropylene or PVDF construction
+ Powerful neodymium magnets
+ Close-coupled design
+ Threaded (NPT or BSP), union or flange connections
+ Impeller trims available every 1/8” (.32 cm) between smallest and largest diameter
+ Back pullout design
+ Mounts to NEMA and IEC (B5 & B14) motor frames
+ Easy set measurement free drive
+ ISO 1940 G2.5 balancing
+ CE certified
+ High working pressure up to 90 psi (6.2 bar)
+ Specific gravity up to 1.8
+ Polypropylene—180o F (82o C)
+ PVDF—220o F (104o C)
APPLICATIONS+ Rail cars & tanker trucks
+ Tanks with an opening on top
+ Sumps and reservoirs
+ Below grade storage tanks
+ Over-the-wall applications
+ When run-dry protection is needed
+ and many more!
0
20
40
60
80
100
120
140
160
180
0 25 50 75 100 125 150 175 200 225 250 275
FLOW (US gpm)
NPS
HR
(ft)
0
10
20
30
40
50
0 5 10 15 20 25 30 35 40 45 50 55 60
FLOW (m/hr)3
#1
#2
#3
#4
#5
Curve Legend#1- 7.00" (177.8 mm)#2- 6.50" (165.1 mm)#3- 6.00" (152.4 mm)#4- 5.50" (139.7 mm)#5- 5.00" (127.0 mm)
13 BHP
10 BHP
7.5 BHP
5 BHP
3 BHP
45%
40%
35%20%
48%
10%
Minimum Continuous Flow 10 US gpm (2.3 m3/hr)
30%
NPSHR
HEA
D (
ft)
HEA
D (m
)N
PSHR
(m)
0
5
10
15
20
25
30
35
40
0 5 10 15 20 25 30 35 40 45 50
Curve Legend#1- 7.00" (177.8 mm)#2- 6.50" (165.1 mm)#3- 6.00" (152.4 mm)#4- 5.50" (139.7 mm)#5- 5.00" (127.0 mm)
#1
#2
#3
#4
#5
40%
35%20%
43%10%
30%
5.5 kW
4.0 kW
3.0 kW2.2 kW
1.5 kWMinimum Continuous Flow 2.3 m 3/hr
NPSHR
FLOW (m3/hr)
NPS
HR
(m
)H
EAD
(m
)
SP22 PERFORMANCE Flooded Suction 3450 RPM*
SP22 PERFORMANCE Flooded Suction 2900 RPM*
SP SERIES
FINISH THOMPSON INC. - UNITED STATES 921 Greengarden Road | Erie, PA 16501 800.934.9384 | ph 814.455.4478 | fx 814.455.8518email [email protected]
FINISH THOMPSON INC. - GERMANYOtto-Hahn-Strasse 16 | Maintal, D-63477 Germany49 (0)6181-90878-0 | fx 49 (0)6181-90878-18email [email protected] finishthompson.com
Hastelloy® C is a registered trademark of Haynes International, Inc.
Dimensions and weights are for reference only. Weights listed are for pump only; motor not included.†Varies with motor manufacturer.
*Fill plug not shown
Description Polypropylene PVDF
1 Housing4 Separator plate6 Inner volute7 Impeller
Glass-fiber reinforced
polypropylene (GF PP)
Carbon-fiber reinforced
PVDF (CF PVDF)
3A, O-ring options5, 10
FKM, EPDM
3 Fill and drain plugs* Polypropylene PVDF
6A Inner volute thrust ring
High purity alumina ceramic, or silicon carbide (SiC)
7A Impeller thrust ring GF molybdenum disulfide filled PTFE or SiC
8 Inner drive Neodymium iron boron
magnets encapsulated in
unfilled polypropylene
Neodymium iron boron
magnets encapsulated in
unfilled PVDF
8A Bushing Carbon, PTFE, high purity alumina ceramic, or SiC
9 Shaft High purity alumina ceramic, Hastelloy® C, or SiC
11 Barrier GF PP CF PVDF
11A Barrier thrust ring High purity alumina ceramic
12 Motor adapter Ductile iron
13 Outer drive magnets Nickel-plated neodymium iron boron magnets/steel
14 NEMA motor adapter sealing kit
Buna N, FKM, or EPDM
Specifications
Dimensions
3
1
4
7
7A
88A
9
13
14
11A11 12
106A65
3A
6 1/2"[16.5cm]
'A' 6 1/8"[15.6cm]
7 3/4"[19.7cm]
5"[12.7cm]
'D' †
8 1/8"[20.6cm]
916
"[1.4cm]
3 1/2"[8.9cm]
1 3/4"[4.4cm]
12 7/16"[31.6cm]
4 9/32"[10.9cm]
'B''C'†
2" FNPT OR FBSP 2" FNPT OR FBSP
6 25/32"[17.2cm]
17 13/16"[45.2cm]
Motor Frame A B C† D† lbs. [kg] PP lbs. [kg] PVDF
NEMA 145TC 3-1/2” [8.8 cm] 18-11/16” [32.2 cm] 29-29/32” [76.0 cm] 11-11/16” [29.7 cm] 54 [24.5] 45 [20.0]
NEMA 184TC 4-1/2” [11.4 cm] 17-13/16” [45.2 cm] 31-1/16” [78.9 cm] 12-15/32” [31.7 cm] 46 [20.9] 52 [23.6]
NEMA 213/215TC 5-1/4” [13.3 cm] 18-11/32” [46.6 cm] 34-11/16” [88.1 cm] 14-1/32” [35.7 cm] 51 [23.1] 57 [ 25.9]
IEC 90 w/B14 or B5 3-17/32” [9.0 cm] 18-11/16” [47.5 cm] 29-11/16” [75.4 cm] 11-11/16” [29.7 cm] 54 [29.7] 60 [27.2]
IEC 100 w/B14 or B5 3-15/16” [10.0 cm] 18-11/16” [47.5 cm] 31-1/8” [79.1 cm] 12-1/8” [30.8 cm] 54 [24.5] 60 [27.2]
IEC 112 w/B14 or B5 4-13/32” [ 11.2 cm] 18-11/16” [47.5 cm] 31-7/8” [81.0 cm] 12-1/8” [30.8 cm] 54 [24.5] 60 [ 27.2]
IEC 132 w/ B14 or B5 5-3/16” [ 13.0 cm] 18-3/4” [ 47.6 cm] 34-27/32” [88.5 cm] 14-3/16” [36.0 cm] 57 [25.9] 63 [28.6]
Also available 2” x 2” or 3” x 2” 150 lb. ANSI/ISO PN20/PN40/JIS 10K or 63mm x 63mm union connection. Flanges are in compliance with bolting dimensions only.
