SONY DSC-S600 SERVICE MANUAL LEVEL 2 VER 1.2 2007.10 (9-876-922-33)
-
Upload
fernanda-llanos -
Category
Documents
-
view
304 -
download
8
Transcript of SONY DSC-S600 SERVICE MANUAL LEVEL 2 VER 1.2 2007.10 (9-876-922-33)
SERVICE MANUAL LEVEL 2
Revision HistoryRevision History
How to useAcrobat Reader
How to useAcrobat Reader
Sony EMCS Co.
2007J0800-1 ©2007.10
Published by Kohda TEC9-876-922-31DSC-S600_L2
DSC-S600
Internal memoryON BOARD
Internal memoryON BOARD
US ModelCanadian Model
AEP ModelUK Model
E ModelAustralian Model
Chinese ModelBrazilian Model
Hong Kong ModelKorea Model
Ver. 1.2 2007. 10
DIGITAL STILL CAMERA
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
• Precaution on Replacing the SY-145 board
— 2 —DSC-S600_L2
SPECIFICATIONS
Camera[System]Image device 7.18 mm (1/2.5 type) color
CCD, Primary color filter
Total pixel number of cameraApprox. 6 183 000 pixels
Effective pixel number of cameraApprox. 6 003 000 pixels
Lens Carl Zeiss Vario-Tessar3 zoom lensf = 5.1 – 15.3 mm (31 – 93 mm when converted to a 35 mm still camera)F2.8 – 5.1Automatic ND filter switching
Exposure control Automatic exposure, Scene Selection (7 modes)
White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent
File format (DCF compliant)Still images: Exif Ver. 2.21JPEG compliant, DPOF compatibleMovies: MPEG1 compliant (Monaural)
Recording media Internal Memory (32 MB)“Memory Stick Duo”
Flash Recommended distance (ISO set to Auto): approx. 0.2 m to 7.0 m (7 7/8 inches to 275 5/8 inches) (W)/approx. 0.5 m to 3.8 m (19 3/4 inches to 149 5/8 inches) (T)
[Input and Output connectors]USB jack mini-B
USB communication
Hi-Speed USB (USB 2.0 compliant)
[LCD screen]LCD panel 5.1 cm (2.0 type) TFT drive
Total number of dots84 960 (354×240) dots
[Power, general]Power R6 (size AA) Alkaline batteries
(2), 3 VHR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2, not supplied), 2.4 VZR6 (size AA) Oxy Nickel Primary Battery (2, not supplied), 3 VAC-LS5K AC Adaptor (not supplied), 4.2 V
Power consumption (during shooting with the LCD screen on)
1.0 W
Operating temperature0°C to +40°C (+32°F to +104°F)
Storage temperature–20°C to +60°C (–4°F to +140°F)
Dimensions 99.952. 0×36.8 mm(4×2 1/8×1 1/2 inches)(W/H/D, excluding protrusions)
Mass Approx. 181 g (6.4 oz) (including two batteries and wrist strap, etc.)
Microphone Electret condenser microphone
Speaker Dynamic speaker
Exif Print Compatible
PRINT Image Matching IIICompatible
PictBridge Compatible
Design and specifications are subject to change without notice.
These specifications are extracted from instructionmanual of DSC-S600 (2-658-425-11).
— 3 —DSC-S600_L2
1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.
2. Check the interboard wiring to ensure that no wires are"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.
5. Check the B+ voltage to see it is at the values specified.6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚Cduring repairing.
• Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).
• Be careful not to apply force on the conductor when solderingor unsoldering.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!
• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
— 4 —DSC-S600_L2
TABLE OF CONTENTS
1. SERVICE NOTE1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY ······1-11-2. METHOD FOR COPYING OR ERASING THE DATA IN
INTERNAL MEMORY ··················································1-21-3. PRECAUTION ON REPLACING THE SY-145
BOARD ···········································································1-31-4. INITIAL LANGUAGE DATA CHECK ··························1-31-5. HOW TO OPERATE THE CAMERA WITHOUT THE
FRONT CABINET ··························································1-3
2. DISASSEMBLY2-1. DISASSEMBLY ······························································2-3
3. BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAM ····································3-13-2. POWER BLOCK DIAGRAM ·········································3-3
4. PRINTED WIRING BOARDS ANDSCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ································4-14-2. SCHEMATIC DIAGRAMS ············································4-54-3. PRINTED WIRING BOARDS ·····································4-274-5. MOUNTED PARTS LOCATION ·································4-36
5. REPAIR PARTS LIST5-1. EXPLODED VIEWS ······················································5-35-2. ELECTRICAL PARTS LIST ··········································5-6
1-1DSC-S600_L2
1. SERVICE NOTE
Self-diagnosis display• C: ss: ss
You can reverse the cameramalfunction yourself. (However,contact your Sony dealer or localauthorized Sony service facilitywhen you cannot recover from thecamera malfunction.)
• E: ss: ssContact your Sony dealer or localauthorized Sony service facility.
1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Display Code
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Cause
Trouble with hardware.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
E:92:ss
Turn the power off and on again. Trouble with internal memory. INTERNAL MEMORY ERROR
Checking of lens drive circuit. When failed in the focus and zoominitialization.
—Checking of flash unit or replacementof flash unit.
Insert batteries correctly.
Abnormality when flash is beingcharged.
Batteries are not inserted correctly.
Format the “Memory Stick Duo” orinternal memory.
“Memory Stick Duo” or internal memory isunformatted.
Insert a new “Memory Stick Duo”. “Memory Stick Duo” is broken.
1-2DSC-S600_L2
Copies all images in the internal memory to a “Memory Stick Duo”.
1 Insert a “Memory Stick Duo” having 32 MB or larger capacity.2 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v, then press z.Copying starts.
Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files using batteries with little remaining capacity, the batteries may run out, causing copying to fail or possibly corrupting the data.You cannot copy individual images.The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in
(Internal Memory Tool) (page 46).You cannot select a folder copied on a “Memory Stick Duo”.Even if you copy data, a (Print order) mark is not copied.
Copy
OK See the following procedure.
Cancel Cancels the copying.
This item does not appear when a “Memory Stick Duo” is inserted in the camera.The default settings are marked with .
Formats the internal memory.• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1 Select [OK] with v on the control button, then press z.The message “All data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z.The format is complete.
Format
OK See the following procedure.
Cancel Cancels the formatting.
1-2. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORYThe data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note1: When replacing the SY-145 board, erase the data in internal memory of the board before replacement.Note2: When replacing the SY-145 board or the IC203 on the SY-145 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
1-3EDSC-S600_L2
1-5. HOW TO OPERATE THE CAMERA WITHOUT THE FRONT CABINET
Cabinet (front) assembly
LB-117 board
Remove the claw
LB-117 board
S101 switch(Lens barrier open)
SW-461 board
Adhesive tape
solder the leads
Remove the LB-117 board from the cabinet (front) asembly, solder the leads to the SW-461 board, and fix the S101 switch (Lens barrier open) to the ON position with an adhesive tape.
1-3. PRECAUTION ON REPLACING THE SY-145 BOARD• The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not required.• Perform “Initial Language Data Check” mentioned below, and also the adjustment items necessary after SY Board replacement.
1-4. INITIAL LANGUAGE DATA CHECKIf the SY-145 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initiallanguage as that of the set distributing in each region.
Initial language: Language displayed at the next starting if the setting of Setup menu was reset.It is different from the language setting selectable with the menu.
Initial Language Data
Note: GP2 is fixed to English.GP3 is either English, Spanish, or Russian.GP4 is either English, Spanish, Portugal, Simplified Chinese, or Korean.
Writing Method:1) Select page: 00, address: 01 and set data: 01.2) Select page: 4F, address: 8C, and set the Initial Language Data.3) Select page: 40, address: 38, and set data: 00.4) Click [Save] on the SEUS screen.5) Select page: 80, address: 34, and check that the data is “00”.6) Select page: 80, address: 30, and check that the data is “00”.7) Select page: 00, address: 01, and set data: 00.8) Turn off the camera.9) Turn on the camera. Execute “Initialize” of Setup screen.10) Check the language displayed when the camera starts.
Page Address Data Language GP2 GP3 GP4
4F 8C
00 English z z z
04 Spanish z z
06 Portugal z
08 Simplified Chinese z
0B Russian z
0D Korean z
DSC-S600_L2
LinkLink
2. DISASSEMBLY
HELP
DISASSEMBLYDISASSEMBLY
HELP
COMMON NOTE FOR DISASSEMBLYCOMMON NOTE FOR DISASSEMBLY
2-1
2. DISASSEMBLY2. DISASSEMBLY
DSC-S600_L2
2. DISASSEMBLY
NOTE FOR REPAIR
DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITORThe charging elect capacitor 180uF (330V) is charged up to themaximum 300 V potential.There is a danger of electric shock by this high voltage when thecapacitor is handled by hand. The electric shock is caused by thecharged voltage which is kept without discharging when the mainpower of the DSC-S600 is simply turned off. Therefore, theremaining voltage must be discharged as described below.
Preparing the Short JigTo preparing the short jig. a small clip is attached to each end ofa resistor of 1 kW /1 W (1-215-869-11)Wrap insulating tape fully around the leads of the resistor toprevent electrical shock.
1 kΩ/1 W
Wrap insulating tape.
Make sure that the flat cable and flexible board are not cracked of bent at the terminal.Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt which comes off at the point.(Take care that there are some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.Be in danger of the snapping of a wire.
Discharging the CapacitorShort circuits between the positive and the negative terminals ofcharged capacitor with the short jig about 10 seconds.
SY-145
Shorting jig(1kΩ / 1W)
Capacitor
DSC-S600_L22-3 2-4
2-1. DISASSEMBLYThe following flow chart shows the disassembly procedure.
2. DISASSEMBLY 2. DISASSEMBLY2. DISASSEMBLY
SY-145
SY-145
SY-145SY-145
5
7
6
2
3
4
1
2
3
5
1
8
4
3
2
1
1 Slide the BT cover.
2 Screw (M1.7x4)
3 Open the USB cover.
4 Screw (M1.7x4)
5 Screw (M1.7x4)
6 Screw (M1.7x4)
7 Open the cabinet (upper) assembly.
8 Cabinet (rear) assembly
1 Three solderings
2 Two solderings
3 Open the BT cover.
4 Open the cabinet (upper) assembly.
5 Cabinet (front) assembly
1 Two solderings
2 Flexible board (from the LCD unit)
3 LCD unit
1 Two solderings
2 Claw
3 Two claws
4 Flexible board (from the lens block assembly)
5 Flexible board (from the lens block assembly)
6 Flexible flat cable (FFC-058)
7 Flexible flat cable (FFC-056)
8 SY-145 board, RL-063 board,
speaker, microphone, etc.
1
4
3
2
1 Screw (M1.7x4)
2 Two claws
3 RL-063 board
4 Cabinet (upper) assembly
1
2
8
3
5
6
4
A (See page 2-5)
C (See page 2-5)
B (See page 2-5)
7
Refer to page 2-1 "DISCHARGING OFTHE FLASHLIGHT POWER SUPPLYCAPACITOR (LND904, LND905)", when discharging the capacitor.
HELP 02
HELP 01
HELP 03
HELP 04
DSC-S600_L2
2. DISASSEMBLY2. DISASSEMBLY
2-5 2-6E
SY-145SY-145
SY-145
SY-145
A
C
B
3
1
4
1
5
1 Flexible flat cable (FFC-058)
2 Flexible board (from the optical unit)
3 Screw (M1.7x4)
4 LCD frame
5 SW-461 board, flexible flat cable (FFC-058)
1 Two solderings
2 Speaker holder
3 Speaker
4 Two solderings
5 Miclophone holder
6 Miclophone
HN-015
1 Two solderings
2 Elect 180uF (330V) capacitor
3 Three solderings
4 Flash unit, harness (HN-015)
5 SY-145 board, RL-063 board,
flexible flat cable (FFC-056), etc.
4
1
2
3
1
2
4
5
2
4
1 Flexible board (from the lens block assembly)
2 Flexible board (from the lens block assembly)
3 Flexible board (from the optical unit)
4 Lens block assembly, optical unit.
3
2
HELP 05
HELP 06
3
5
6
RL-063SW-461
DSC-S600_L2HELP
HELPDisassembling and assembling procedures that require attention are described here.
Mode Switch of
the SW-461 board
Cabinet (rear) assembly
HELP 01
When installing the Cabinet (Rear) assembly, install it while aligning the Mode switch of the SW-461 board with the position A of the Cabinet (Rear) assembly.
A
Yellow
Two reads (from the BM-001 board)
Tree reads (from the LB-117 board)
Red
SW-461 board
Black
Gray
White
HELP 02
Solder each lead according to the color (Y: yellow, G: gray, W: white, R: red, B: black) displayed on the SW-461 board.
DSC-S600_L2HELP
SY-145
When installing the cabinet (front) asembly, put the lead lines in the space between the tripod screw and the SW-461 board.
When installing the cabinet (front) asembly, put the lead lines in the space between the optical unit and the DC mortor.
HELP 03
SW-461 board
Tripod screwDC mortor
Optical unit
Solder each lead according to the color (R: red, B: black) displayed on the SY-145 board.
Black
Red
LCD leads
SY-145 board
HELP 04
DSC-S600_L2HELP
HELP 05
BlackRed
SY-145 board
Speaker
Mic unit
Solder each lead according to the color (R: red, B: black) displayed on the SY-145 board.
HELP 06
Give folding to the flexible flat cable (FFC-057).
SY-145 board
SY-145 board
RL-063 board
Peak folding
Peak folding
Valley folding
Valley foldingRL-063 board
Flexible flat cable (FFC-057)
Flexible flat cable (FFC-057)
DSC-S600_L2
LinkLink
3. BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM POWER BLOCK DIAGRAMOVERALL BLOCK DIAGRAM POWER BLOCK DIAGRAM
DSC-S600_L23-1 3-2
3-1. OVERALL BLOCK DIAGRAM
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
IC101CAMERA DSP
SYSTEM CONTROL
IC301
TIMINGGENERATOR
S/HA/D CONV.
CCD IMAGER
IC601MIC AMP
SPEAKER AMP
7780
3740444853
56
60
92
11,816,129,915,6
88,10290,79,76
97,98,100,101103,104,105,32,4,7,10,14,18
8
191720183
H1A,BH2A,BRG
V1A,BV2
V3A,BV4
V5A,BV6
V7A,BV8 VST
XMS IN
4,3,5,7,2,8
6
CN002
CN1001
CN703
CN006
IRISSHUTER
C5C6B6
E1
F2
H5
J5
AC1
AD1
E9B8
F3E3
A5A2
B10 A4
CN301
X101
EXTAL
CCD OUT
CN301LENS TEMP1
SENSOR LENSTEMP1
LENSTEMP2
CN401
CA AD0 - CA AD13
CLK TGO
CA HD CA FD
D23
R4
D9
E4A6
C1
AF4
U4
F22
E22
L23
K23
L22
XACCESS LED
32-24,22,13-1133
E6
E5
MS D0-MS D3, MS BS, MS CLK MS D0-MS D3, MS BS, MS CLK
L26
K25
AA23
K26
DSP QCLK
MEMORYSTICKDuo
CONNECTOR
LCDBACKLIGHT
B6
LENS UNIT(LSV-951A)
CD-606 FLEXIBLE BOARD SY-145 BOARDSW-461 BOARD (2/3)
D003(ACCESS)
SAN1
SO,
XSAN
1SCK
SOSI
SCK
SOSISCK
IC004,005
IC001
14
58
14
11
1
2
8
6|3
8
13,12,14,16,11,17
15
17|
22242523
2726
30
2.0 INCHCOLOR DIGITAL
LCD PANEL
LCD901
XSAN RST OUT
KEY AD0
KEY AD1
XAE LOCK SWXSHUTTER SW
MODE DIAL 0
AUIN
E4Y26XCS_AUDIO
AUOUT
XPWR LED
XSTRB LED
XAE LOCK LED
OVF SENS
XPWR ON
XAF LED
BL HBL L
STRB CHGXSTRB FULLSTRB CHG CONT
STRB ON
SAN1 SO, XSAN1SCK
LCD CK
LCD HDLCD VD
LCD D2-D7
BATTERYHOLDER
A8D4
A7
B7
C7
C9
OSC I
A9 OSC O
X00132.768KHz
F001
F002
A 2.9VCAM 12V
EVER 3.1VEVER 2.9VD 3.2VA 3.2VMS VCCCAM 2.9VD 1.8VM 5VD 1.2VCAM -7.5VBL HBL L
ST UNREG
UNREGBATT UNREG
BATT GND
BATT SENS
XDD RST OUT
XPWR ON
USB VBUS
XMS IN
VL 3V
XPWR OFF
BATT SENS
XDD RST OUT
XPWR OFF
2.9V/12V REG
B8
89 93
DC/DC CONVERTERREAL TIME CLOCK
AC4,AE4AE5,AC5AB6,AF6
E8,E7,D6D5,E6,B4
K5,G4,H4,L5H2,H1,J1,J2M5,J4,K4,M6
K2,K1
N21P23
U2
T2
R6
SAN1 SO, SI, SCK, XSAN1SCK
SAN1 SO, SI, SCK
12MHzXTAL OSC
X10233.75MHz
CLKTGEXTXTAL OSC
AB5
AA5
Y5
SAN0 SO, SI, XSAN0SCK
FFC-056 (FLEXIBLE FLAT CABLE) (2/3)
(2/8)
(1/8)
(4/8)
(3/8)
(4/8) (4/8)
(5/8)
(6/8)
(2/8)
(8/8)
(8/8)
1
2
ST UNREG
HIGH VOLTAGECHAGER
IGBT DRIVE
FLASHDRIVE
C9001MAINCAPACITOR
FLASHUNIT
XENONTUBE( )
T901
Q901 XE K(L)
XE A(H)
D901(RECT)
10
15
9
6
4 7IC901
TRIGGERCOIL
FFC-057 (FLEXIBLE FLAT CABLE)
S202
POWER
S201
SHUTTER
D201 (POWER)
LED901(AF LED)
XAF LED
RL-063 BOARD76
2
3
8
FFC-056 (FLEXIBLE FLAT CABLE) (3/3)
S001, 004, 002, 005, 003
DOWN, RIGHT, UP, LEFT, SET
S011
D001 (FLASH)
D002 (AE LOCK)
MOVIE / STILL / PLAY
S007, 009, 008, 010, 006
DISPLAY, DUST, MENU, ZOOM WIDE, ZOOM TELE
SW-461BOARD
(3/3)3,2
1
(USB)CN003
BT001LITHIUMBATTERY
(SECONDARY)
CN006
VL 3V
USB VBUS5
6
20
22
21
23
FFC-058 (FLEXIBLE FLAT CABLE)
OPTICALVIEWFINDERUNIT
OVF RESETSENSOR
OVF ZOOMMOTOR
OVF SENS
MCN001
4 |1
7
SP901SPEAKER
MIC901MICROPHONE
MICMIC SIG
SP+SP-
SAN1 SO, XSAN1SCK
D+, D-USB DP, USB DM
IRIS ENIRIS IN
IRIS DRIVE
FOCUS MOTOR DRIVE
ZOOM MOTOR DRIVE
LENS BARREIERMOTOR DRIVE
HALL AMP
IC401
E1F1D1C1
H3C2G3B1
IRIS +IRIS - B8
C7
SAN LENSV OPENSAN LENSV CLOSE
LENSV OPENLENSV CLOSE
ZM SENS 2ND
ZM SENS 1ST
LENSV OPENLENSV CLOSE
H8D6
F7G7
ZM ENZM DIR AZM DIR B
F8E8
MSHUT ENMSHUT DIR
SHUTTER DRIVE
OVF ZOOM DRIVE
IC402B3B4
D1B1
FOCUS +FOCUS -
ZOOM AZOOM XAZOOM BZOOM XB
F2F3E6D6
B5B6C6C5
H1F2
HALL +HALL - A5
A8
SHUTTER+SHUTTER-
OVF ENOVF DIR AOVF DIR B
F5
G4
G6SAN1 SO, SI, XSAN1SCK
XSAN RST OUT
SAN 27M CLK0H6
F4
FFC-056 (FLEXIBLE FLAT CABLE) (1/3)
SW-461BOARD
(1/3)
BM-001BOARD
LB-117 BOARD
M001LENS BARRIER
MOTOR
XLENSVOPEN SENS
XLENSVCLOSE SENS
M
S101LENS BARRIER
OPEN( )
( )S102
LENS BARRIERCLOSE
26
25
CN006
2423
IRIS MOTOR
ZOOM RESETSENSOR1
ZOOM RESETSENSOR2
M23222019
2633
1815
FOCUS MOTOR
MZOOM MOTOR
M
53
24
12
10
1421
SHUTTER MOTOR
M
H
OVF AOVF BOVF XAOVF XB
OVF AOVF BOVF XAOVF XB
IC203SUPER AND
FLASH MEMORY
IC201BURST
FLASH MEMORY
CPU_D0-D15
D0-D15 D0-D15A1-A21
CPU_A1-A21,A25
A20,A21,A25
AB13,AA13,AE13,AF13,AF12,AE12,AA12,AC12,AC11,AB12,AE11,AF11,AE10,AB11,
AC10,AB10
AF21,AF20,AE20,AB18,AB19,AC19,AB16,AE19,AF19,AF18,AE18,AA15,AC18,AC17,AB15,AE17,AF17,AE16,AB14,AC16,
AC15,AE14
IC202256MbitSDRAM
D21,D22,D20,B22,A22,A23,B23,E20,E21,B24,A24,A25,B25,C25,C26,B26,E10,A10,D10,E11,B10,A11,B11,E12,D11,D12,F12,B12,A12,E13,
D13,D14
D17,D18,D16,B18,A19,B19,E16,D19,E19,E17,
B20,A20,E18
D0-D31
A0-A12
IRIS ENIRIS IN N4
P4
ZM SENS 1STZM SENS 2ND V4
U5
SAN LENSV OPENSAN LENSV CLOSE
LENS TEMP1LENS TEMP2 J25
K22XLENSV OPEN SENSEXLENSV CLOSE SENSE Y22
AC23
ZM ENZM DIR AZM DIR B
MSHUT ENMSHUT DIR R5
R25
R26Y4
AC14AA14
N2
N6
M2
L4
L2
N5
SAN 27M CLKOAF9
A18
OVF ENOVF DIR AOVF DIR B
R22
V23
AB22
OVF AOVF BOVF XAOVF XB
CCD IMAGER and CD-606 FLEXIBLE BOARD are included in the LENS BLOCK ASSY (A-1156-857-A).
DSC-S600_L23-3 3-4E
3-2. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
E10LX3
E9VO3
LV3
RS3
G9BG4
TG4 F10
PSG4 G8
D002(RECT)
D003(RECT)
L005
BL H
BL H
BL L
F9
F8
BL L
-7.5V ON
-7.5V54
2 1
3
1
4
5
2
3
-7.5V ON
M 5V M 5V
D 3.2V
A 2.9V, D 1.8V, D 1.2V, MS VCC
D 1.2V
CAM 12V
PANEL 15V
PANEL 15V
Q1002
D1002
CAM 15V CD
CCD IMAGER and CD-606 FLEXIBLE BOARD are included in the LENS BLOCK ASSY (A-1156-857-A).
D 3.2V
M5V
D 3.2V
D 1.8V
A 2.9V
D 3.2V
D 3.2V
D 3.2V
D 3.2V
D 1.8V
Q005, 006
15V
A 2.9V
MS VCC
CAM 2.9V
CAM -7.5V CAM -7.5V CD
ZM RST1 VCC
ZM RST2 VCCL008
Q001SWITCHING
Q003SWITCH
Q002RECT
MS PWR IN
MS PWR
G1
G2
PWR56 OUT
UNREG2
LDO2
LDO1
RTC BAT
UNREG1-1,2
LDO2IN
C10LX2
D8VFB2
D10PWR2
H9VFB5
B8
B3
A3
F7VFB4
L003
L006L301
R402
CN401
CN1001
CN301
R401
L201
VO1-1VO1-2
H2VFB1
PWR1-1PWR1-2PWR1-3
LX5-1LX5-2LX5-3LX5-4
J9
J10
K9
K10
XCS DDSAN0 SOSAN0 SIXSAN0 SCK
XCS DDSAN0 SOSAN0 SI
XSAN0 SCK
A6
C5
C6
B6
J7K7
J6K6
F1F2J1
K1
R26
Y4
341
IC0042.9V REG
135
IC00512V REG
CCD IMAGER
IC402SHUTTER DRIVEOVF ZOOM DRIVE
M 5V
IC601MIC AMP
SPEAKER AMP
IC401IRIS DRIVE
FOCUS MOTOR DRIVEZOOM MOTOR DRIVE
IC301S/H
A/D CONV.TIMING GENERATOR
1.8V REG
LDO3
LDO3IN
VL 3V
R041
EVER 2.8V
B7XPWR OFF
XPWR OFF
C7XPWR ONXPWR ON XPWRON1
D3MS PWR ON MS PWR ON
BATT SENSD4 DTG1
XDD RST OUTA7
K25
AA23
T25
XRESET
B2
A2
2.9V REG
A1B1C2
L0023.1V REG
IC001DC/DC CONVERTERREAL TIME CLOCK
A8 OSC I
A9 OSC O
X00132.768KHz
IC101CAMERA DSP
SYSTEM CONTROL
IC202256MbitSDRAM
W23
AB5
AA5
Y5
IC201BURST
FLASH MEMORY
IC203SUPER AND
FLASH MEMORY
P25
AB22
-7.5V ON
SY-145 BOARD
RL-063BOARD
SW-461BOARD
BATTERYHOLDER
D001
R002
F001
F002UNREG
ST UNREG ST UNREGBATT UNREG
BATT GND
CN703
CN006
CN001
R22
V23
STRB CHGXSTRB FULLSTRB CHG CONT
STRB CHG
XSTRB FULL
STRB CHG CONT
D 3.2VA 2.9VD 1.2V
D 1.8V
D 3.2V
D 3.2V
9 MS VCC
D 3.2V
D 3.2V
SD 1.8V
POWERS202
A4 XAF LEDXAF LED
D23
E22
XPWR LED
XPWR LED
XSTRB LED
XSTRB LED
D201 (POWER)
RST VCC
D001 (FLASH)
LED901(AF LED)
VL 3VBT001
LITHIUM BATTERY
(SECONDARY) CD-606 FLEXIBLE BOARD
ZOOMRESET2SENSOR
ZOOMRESET1SENSOR
LENS UNIT(LSV-951A)
8
13
1
5
98
2
18
9
6
F003
Q004SWITCHING & RECT
H7VFB6
H6GT6 L009
FFC-058 (FLEXIBLE FLAT CABLE)
FFC-057 (FLEXIBLE FLAT CABLE)
FFC-056 (FLEXIBLE FLAT CABLE)
OPTICALVIEWFINDERUNIT
R009
CN002
MEMORYSTICKDuo
CONNECTOR
3
4
2
8
L901
1
2
HIGH VOLTAGECHAGER
IGBT DRIVE
T901XE A(H)
D901(RECT)
15
10
9
6
3
IC901C9001MAINCAPACITOR
VCC1VGHVDD
LCDBACK LIGHT
2.0 INCHCOLOR DIGITAL
LCD PANEL
LCD9019
1011
L1002
L1001
D 3.2VDETECT
Q1001
OVF RESETSENSOR
(8/8)(8/8)
(8/8)
(5/8)
(6/8)
(1/8)
(2/8)
(2/8)
(3/8)
(4/8)
(4/8)
(4/8)
FLASHUNIT
XENONTUBE( )
H1
DSC-S600_L24-1
4-1. FRAME SCHEMATIC DIAGRAM
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-2 FRAME SCHEMATIC DIAGRAM
LND908TRIGGER
33PCN1001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
10P
CN
703
1 2 3 4 5 6 7 8 9 10
LND905
LND601
LND403
CN
006
26P
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
33PCN301
1CAM-7.5V-CD
2REG_GND
3RG
4REG_GND
5CAM15.0V-CD
6POWER_SAVE
7REG_GND
8CCD_OUT
9CCD_GND
10REG_GND
11V8
12V7B
13V7A
14VSUB_CONT
15SHT
16REG_GND
17H1B
18H2B
19H1A
20H2A
21REG_GND
22V6
23VHLD
24V5B
25V5A
26V4
27VST
28V3B
29V3A
30V2
31V1B
32V1A
33TH2
CN003
1VCC
2D-
3D+
4ID
5GND
CN001 8P
8
7
6
5
4
3
2
1
LND004LN
D00
2
BAT
T_G
ND
LND038
LND602
CN002
1
2
3
4
5
6
7
8
9
10
LND401
LND402
LND101
LND102
LND103
LND003
LND906XE_A(H)
LND907XE_K(L)
LND604
26
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
M001
LND040
33PCN401
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
LND039
LND404
LND041
LND904
LND037
LND603
LND
001
BAT
T_U
NR
EG
10P
1 2 3 4 5 6 7 8 9 10
9P
123456789
9P
123456789
1
A
XM
S_I
N
PT_E/LED_K1
VCC1
XSCK
XA
CC
ESS
_LED
SI
D2
MS
_D3
MS
_D1
VL_
3V
XA
CC
ESS
_LED
ZM_RST2_VCC
KEY
_AD
0
COMOUT
RST_VCC
VVCOM
REG
_GN
D
D1
ZM_O
VF_
XB
ZOOM_A
REG
_GN
D
KEY
_AD
1
VSH
VC
C
D-
MO
DE_
DIA
L0
MS
_CLK
DATA2
ZM_O
VF_
XA
LCD BACK LIGHT(Included in the LCD901)
DCK
BIAS+
MS
_VC
C
MIC
KEY
_AD
1
BLON
SHUTTER-
D+
XOVF_RST_LED
GND2
COMDC
ZOOM_XA
PT_E/LED_K2
KEY
_AD
0
MAIN CON-
ZOOM_XB
ZOOM_A
ND-
HALL-
VC
C
VGL
XA
E_LO
CK
_LED
ZM_OVF_B
ZM_OVF_XB
XLENSV_CLOSE_SENSE
VL_
3V
XVD
ZOOM_XA
MIC_SIG
BL_L
BIAS-
VCOM
MS
_CLK
VBC
XRESET
C2+
FOCUS-
XS
TRB
_LED
MS
_D2
VCC
ND+
D5
MS
_BS
XLE
NS
V_O
PEN
_SEN
SE
OV
F_S
ENS
MIC_GND
N.C.
REG
_GN
D
LENSV_OPEN
MS
_D1
NC
ZOOM_XB
XLENSV_OPEN_SENSE
XLE
NS
V_C
LOS
E_S
ENS
E
D4
INT
LENSV_CLOSE
REG_GND
XLENSV_CLOSE_SENSE
XLENSV_OPEN_SENSE
REG_GND
BL_H
GN
D
VSS
EMIT
TER
MAIN CON+
DATA1
ZM_OVF_XA
GND
N.C.
MS
_D2
N.C.
REG
_GN
D
REG
_GN
D
SCLK
GND
D3
LENSV_CLOSE
SHUTTER-
SP-
LCD9012.0 INCHCOLOR DIGITAL LCD PANEL
XHD
BS
LEN
SV
_OP
EN
TH1
XM
S_I
N
GN
D
D+
LENSV_CLOSE
EMITTER
OVF_SENS
ZM_OVF_A
FFC-057
N.C
.
MO
DE_
DIA
L0
ZOOM_B
VGH
MS
_VC
C
LEN
SV
_CLO
SE
RS
T_V
CC
ND+
SHUTTER+
ZM_SENS_OUT2
TEST
NC
ND-
SDIO/DATA0
OPTICALVIEW FINDER
UNIT
ZM_RST1_VCC
MS
_BS
ZM_O
VF_
B
XLE
NS
V_O
PEN
_SEN
SE
NC
D0
ZM_O
VF_
A
ZM_O
VF_
XB
ZM_O
VF_
XA
XA
E_LO
CK
_LED
XS
TRB
_LED
OV
F_S
ENS
EMIT
TER
N.C
.
RS
T_V
CC
ZM_O
VF_
B
ZM_O
VF_
A
D-
MS
_D0
LEN
SV
_OP
EN
HALL+
SP+ FOCUS+
LENSV_OPEN
GN
D
LENSV_OPEN
LEN
SV
_CLO
SE
C2-
ZM_SENS_OUT1
SHUTTER+
XLE
NS
V_C
LOS
E_S
ENS
E
VSS
VDD
DATA3
D_3
.2V
ZOOM_B
GN
D
MS
_D3
XCS
N.C.
REG
_GN
D
D_3
.2V
MS
_D0
XS
HU
TTER
_SW
N.C
.
XA
E_LO
CK
_SW
XP
WR
_ON
D_3
.2V
N.C
.
REG
_GN
D
XP
WR
_LED
XA
F_LE
D
BL_
H
BL_
L
CCD IMAGER(6M)
CD-606FLEXIBLEBOARD
LENS ASSY
XS
HU
TTER
_SW
N.C
.
D_3
.2V
XP
WR
_LED
XA
E_LO
CK
_SW
N.C
.
XA
F_LE
D
XP
WR
_ON
REG
_GN
D
FLEXIBLEFLAT CABLE
RL-063 BOARD
BATTERYHOLDER
C9001
SP901SPEAKER
HN-007 HARNESS
HN-006 HARNESS
HN-009 HARNESS
HN-008 HARNESS
MIC901MICROPHONE
HN-011 HARNESS
HN-010 HARNESS
BM-001 BOARD
LB-117 BOARD
HN-012 HARNESS
HN-013 HARNESS
HN-014 HARNESS
FLEXIBLEFLAT CABLE
FFC-058FFC-056
FLEXIBLEFLAT CABLE
HN-015 HARNESS
(FLASH)
(CAPACITOR)
SW-461 BOARD LENSBARRIER MOTOR
BT001LITHIUMBATTERY
(SECONDARY)
MEMORYSTICK DuoCONNECTOR
USB
E
I
J
K
D
G
H
C
O
N
F
M
L
B
154 8
16
121152 1413103 6 7 9 16
(1/8)CAMERA A/D CONV.TIMING GENERATOR(2/8)LENS DRIVE(3/8)CAMERA DSP,SYSTEM CONTROL(4/8)SUPER AND,FLASH MEMORY,SDRAM(5/8)ADUIO AMP,MIC,SP(6/8)FLASH DRIVE(7/8)LCD PANEL,CONNECTOR(8/8)DC/DC CONVERTER
SY-145 BOARD
CCD IMAGER and CD-606 FLEXIBLE BOARD areincluded in the LENS BLOCK ASSY(A-1156-857-A).and it is not supplied as an independentservice parts.
LB-117 BOARD (OPEN/CLOSE SWITCH)
BM-001 BOARD (LENS OPEN/CLOSE MOTOR) RL-063 BOARD (POWER SWITCH)
SW-461 BOARD (JACK, FUNCTION SW, LITHIUM BATTERY)LB-117 BOARD (OPEN/CLOSE SWITCH) SW-461 BOARD (JACK, FUNCTION SW, LITHIUM BATTERY)
BM-001 BOARD (LENS OPEN/CLOSE MOTOR) RL-063 BOARD (POWER SWITCH)
COMMON NOTE FOR SCHEMATIC DIAGRAMSCOMMON NOTE FOR SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
LinkLink
DSC-S600_L2
DSC-S600_L24-3
4-2. SCHEMATIC DIAGRAMS4-2. SCHEMATIC DIAGRAMS
Link(For schematic diagrams)• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolyticsand tantalums.
• Chip resistors are 1/10 W unless otherwise noted.kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalumcapacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.Example C541 L452
22U 10UHTA A 2520
• Constants of resistors, capacitors, ICs and etc with XXindicate that they are not used.In such cases, the unused circuits may be indicated.
• Parts with * differ according to the model/destination.Refer to the mount table for each function.
• All variable and adjustable resistors have characteristiccurve B, unless otherwise noted.
• Signal nameXEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor• 5: fusible resistor• C : panel designation• A : B+ Line• B : B– Line• J : IN/OUT direction of (+,–) B LINE.• C : adjustment for repair.• Circled numbers refer to waveforms.(Measuring conditions voltage and waveform)• Voltages and waveforms are measured between the
measurement points and ground when camera shootscolor bar chart of pattern box. They are reference valuesand reference waveforms.(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon inputimpedance of VOM used.)
Precautions for Replacement of imager• If the imager has been replaced, carry out all the
adjustments for the camera section.• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.In addition, ensure that the receiver is not covered withdusts nor exposed to strong light.
1. Connection
2. Adjust the distance so that the output waveform ofFig. a and the Fig. b can be obtain.
When indicating parts by reference number, pleaseinclude the board name.
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)
Kinds of capacitor
Temperature characteristicsExternal dimensions (mm)
Yello
w
A AB BA=B
Fig. a (Video output terminal output waveform)
Electronic beamscanning frame
CRT picture frame
HC
yan
Gre
en
Whi
teM
agen
ta
Red
Blu
e
Fig.b (Picture on monitor TV)
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
Pattern box Front of the lens
L = 1 m (PTB-450)L = 40 cm (PTB-1450)
L Camera
Pattern box PTB-450J-6082-200-AorSmall pattern boxPTB-1450J-6082-557-A
For PTB-450:J-6020-250-A
For PTB-1450:J-6082-559-A
Pattern box Color bar chart
4-2. SCHEMATIC DIAGRAMS
DSC-S600_L24-5
4-2. SCHEMATIC DIAGRAMS
4-6 BM-001/LB-117/RL-063
1
A
LENSV_OPEN
LENSV_CLOSE LENSV_CLOSE
LENSV_OPEN
LND401
LND402 LND404
LND403TOSW-461BOARD
(PAGE 4-7)M
+
–
M001
LENSBARRIER MOTOR
BM-001 BOARDLENS OPEN/CLOSW MOTORXX MARK:NO MOUNT
16
43 5
B
2
HN-011 HARNESS
HN-010 HARNESS
S102S101
3P
1
2
3
1
A
XLENSV_OPEN_SENSHN-012 HARNESS
REG_GND
XLENSV_CLOSE_SENS
TOSW-461BOARD
(PAGE 4-7)
LND101
LND102
LND103
LENS BARRIEROPEN
LENS BARRIERCLOSE
16
XX MARK:NO MOUNT
LB-117 BOARDOPEN/CLOSE SWITCH
43
B
2
HN-013 HARNESS
HN-014 HARNESS
LND209
LND208
S2021
3
2
4
SML-412MWT86D201
S20156
1 3
4 2
9P
1
2
3
4
5
6
7
8
9
LED901
1
A
XSHUTTER_SW
D_3.2V
XAF_LED
XPWR_LED
D_3.2V
REG_GND
XPWR_ON
XAF_LED
XAE_LOCK_SW
N.C.
N.C.
(AFLED)
SHUTTER
POWER
POWER
TOSY-145BOARD(7/8)
16
THROUGHTHE FFC-057 FLEXIBLEFLAT CABLE
(PAGE 4-21 of LEVEL3)
XX MARK:NO MOUNT
RL-063 BOARDPOWER SWITCH
4
C
3 5
B
2
DSC-S600_L24-7 4-8 SW-461
A
16
8
E
6 10
D
G
4
C
3 5
F
7
B
2 91
OPTICAL VIEWFINDER UNIT is replaced as a block.So that there PRINTED WIRING BOARD andSCHEMATIC DIAGRAM are omitted.
10P
1
2
3
4
5
6
7
8
9
10
FB004 0uH
2200x4RB002
33R001
S008
1kR012
6.8BD005
S0052200x4RB001
LND042STATIC_GND
S011
R0091500
S007
CN006 26P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
S003
CN003
5P
1 VCC
2 D-
3 D+
4 ID
5 GND
S006
0uHLF001
LND043 STATIC_GND
D00
1S
ML-
310Y
TT86
CN001 8P
1
2
3
4
5
6
7
8
2200x4RB003
D00
4M
AZW
068H
0LS
0S002
FB003 0uH
SM
L-51
2UW
T86
D00
3
S004
1kR007
D00
2S
ML-
510M
WT8
6S0.1u BC001
CN002
10P
1
2
3
4
5
6
7
8
9
10
0uHFB005
S001
1
3
4 3 3 4
1 2
3 4
1 2
1 6
3 4
1 2
3 4
1 2
2 1 8 7
2 1
8 7
2 1
7 8
1 2
4 3
2 1
4 3
2 1
4 3
2 1
4 3
2 14 3
2 1
2
S009
FB002 0uH
FB001 0uH
R015XX
S010
1kR008
XXD006
BT001
LND044STATIC_GND
LND045 STATIC_GND
D007
2 4
1 3
XX
0uHFB006
0uHFB007
XXC002
XXC004
0.01uB
C003
2P
1
2
3P
1
2
3
DATA3
GND
LENSV_CLOSE
MS_CLK
VCC
MODE_DIAL0
REG_GND
DATA1MS_D1
MS_D0
REG_GND GND
MS_VCC
XMS_IN
LENSV_OPEN
LENSV_CLOSE
GND
MS_D2
VL_3V
KEY_AD0
BS
VCC
MS_D3
DATA2
GND
D+
XLENSV_OPEN_SENSE
XACCESS_LED
SDIO/DATA0
D-
XLENSV_CLOSE_SENSE
LENSV_OPEN
D_3.2V
MS_BS
XLENSV_CLOSE_SENSE
REG_GND
INT
REG_GND
KEY_AD1
XLENSV_OPEN_SENSE
SCLK
ZM_OVF_XB
OVF_SENS
N.C.
ZM_OVF_A
ZM_OVF_XA
RST_VCC
ZM_OVF_B
ZM_OVF_XA
XOVF_RST_LED
XSTRB_LED
ZM_OVF_A
OVF_SENS
EMITTER
ZM_OVF_B
XAE_LOCK_LED
RST_VCC
ZM_OVF_XB
EMITTER
(LITHIUM BATTERY)(SECONDARY)
USB
MEMORYSTICK DuoCONNECTOR
LND037
LND038
HN-011 HARNESS
HN-010 HARNESS
HN-012 HARNESS
HN-013 HARNESS
HN-014 HARNESS
LND039
LND040
LND041
TOSY-145BOARD(7/8)
THROUGH THE FFC-056 FLEXIBLEFLAT CABLE
(PAGE 4-21 of LEVEL3)
(PAGE 4-5)
(PAGE 4-5)
THROUGH THE FFC-058 FLEXIBLEFLAT CABLE
TOSY-145BOARD(7/8)CN703
TOBM-001BOARD
TOLB-117BOARD
(FLA
SH
)
(AEL
OC
K)
(AC
CES
S)
OPTICALVIEWFINDER
UNIT
DOWN
UP
SET
RIGTH
LEFT
DISPLAY
MENU
ZOOM TELE
DUST
ZOOM WIDE
PLAY-STILL-MOVIE
JACK,FUNCTION SW,LITHIUM BATTERYXX MARK:NO MOUNT
SW-461 BOARD
(PAGE 4-21 of LEVEL3)
Schematic diagram of the SY-145 board is not shown.Pages from 4-9 to 4-24 are not shown.
• Refer to page 4-3 for mark 0.
DSC-S600_L2
4-3. PRINTED WIRING BOARDS
LinkLink
LB-117 BOARD SW-461 BOARD
BM-001 BOARD RL-063 BOARD
LB-117 BOARD SW-461 BOARD
BM-001 BOARD RL-063 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATIONCOMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION
DSC-S600_L24-25
4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS
(For printed wiring boards)• : Uses unleaded solder.• : Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated)• Through hole is omitted.• Circled numbers refer to waveforms.• There are a few cases that the part printed on diagram
isn’t mounted in this model.• C: panel designation
THIS NOTE IS COMMON FOR WIRING BOARDS(In addition to this, the necessary note is printed in each block)
• Chip parts.Transistor Diode
2 1
3
1 2
3
2 1
3
2 1
3
345
21
123
654
EB
C
31
55
2
46
123
54
4 3
1 2
5 4
1 3
12
43
31 2
45
53 4
12
34
21
12
43
46
2
5
31
12
43
6 4
1 3
4-3. PRINTED WIRING BOARDS
DSC-S600_L24-27 4-28
4-3. PRINTED WIRING BOARDS
BM-001/LB-117/RL-063
BM-001 (2 layers), LB-117 (2 layers), RL-063 (2 layers)
S101 S102
LND1
01LN
D102
LND1
03
LENS BARRIEROPEN
LB-117 BOARD
1-867-722-11LENS BARRIER
CLOSE
• : Uses unleaded solder.
M
LND401 LND402
LND403
LND404
M001(LENS BARRIER)
1-868-243-11
BM-001 BOARD RL-063 BOARD
19 3
4 1
2
6
51
2
3
A K
4
S201
FFC-057SHUTTER POWER
S202
D201(POWER) LN
D208
LED901(AF LED)
LND2
09
1-867-293-
11
DSC-S600_L24-29 4-30 SW-461
• : Uses unleaded solder.
1 10
+
–
7
8
19
10
6
18
15
76
CN00
1CN
003
C002
C003
C004
LND045
FB006
S011
MOVIE-STILL-PLAY
BT001LITHIUM BATTERY
(SECONDARY)
R009
12
11
10 1
126
CN002
CN006
FFC-058
C001
LND044
FB001FB002
FB003FB004FB005 R001R008
SW-461 BOARD(SIDE A)
1-867-292- 11
1
2
3
4
12
34
1
2
3
4
12
34
1
2
3
4
1 2
3 412
34
1
2
3
4
178
2
1 782 17
8 2
123
1 2
3 4
1 2
3 4
1 2
3 4
AK
S001
DOWN
SETRIGHT LEFT
MENU
UP
ZOOMTELE ZOOM
WIDE
DUST DISPLAY
S002
S003
S004 S0
05
S006
S007
S008
S009
S010
D003
(A
CCES
S)
D004
D005
D006
D007
LND042
RB00
1
RB002
RB003
R007 R015
A K
A K
LF001
D001(FLASH)
D002(AE LOCK)
LND0
37
LND0
38
LND0
39LN
D040
LND0
41
LND0
43
FB007
R012
SW-461 BOARD(SIDE B)
1-867-292-
11
MEMORY STICK DuoCONNECTOR
(USB)
A
B
C
D
E
1 2 3 4 516
SW-461 (2 layers)
Printed wiring board of the SY-145 board is not shown.Pages from 4-31 to 4-34 are not shown.
Waveforms of the SY-145 board is not shown.Page 4-35 is not shown.
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
4-36EDSC-S600_L2
4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS
4-5. MOUNTED PARTS LOCATION no mark : side A* mark : side B
SW-461 BOARD
BT001 A-3
C001 A-1C002 B-5C003 A-4C004 A-4
CN001 A-5CN002 A-1CN003 B-5CN006 A-1
* D001 E-4* D002 E-4* D003 D-1* D004 D-1* D005 D-1* D006 D-1* D007 D-1
FB001 A-2FB002 A-1FB003 A-1FB004 A-1FB005 A-1FB006 A-4
* FB007 D-5
* LF001 D-5
* LND037 D-5* LND038 D-5* LND039 D-5* LND040 D-5* LND041 D-5* LND042 E-1* LND043 C-5
LND044 B-1LND045 B-5
R001 A-2* R007 C-2
R008 A-1R009 B-5
* R012 D-5* R015 C-2
* RB001 D-2* RB002 D-1* RB003 D-1
* S001 C-1* S002 D-1* S003 D-1* S004 D-1* S005 D-2* S006 E-1* S007 C-2* S008 D-2* S009 C-1* S010 E-2
SW-461
Mounted parts location of the SY-145 board is not shown.Page 4-37 is not shown.
NOTENOTE
DSC-S600_L2
LinkLink
5. REPAIR PARTS LIST
LinkLink
OVERALL SECTIONOVERALL SECTION BATTERY HOLDERSECTION
BATTERY HOLDERSECTION
RL-063 BOARD
SW-461 BOARD
SY-145 BOARDBM-001 BOARD
LB-117 BOARD
RL-063 BOARD
SW-461 BOARD
SY-145 BOARDBM-001 BOARD
LB-117 BOARD
A
D
B
E
C
ELECTRICAL PARTS LISTELECTRICAL PARTS LIST
EXPLODED VIEWSEXPLODED VIEWS
ACCESSORIESACCESSORIES
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
SY-145
BCE
AD
DSC-S600_L25-1
5. REPAIR PARTS LIST5. REPAIR PARTS LIST
The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.
NOTE:• -XX, -X mean standardized parts, so they may have some differences from
the original one.• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.• The mechanical parts with no reference number in the exploded views are not
supplied.• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.• CAPACITORS:
uF: µF• COILS
uH: µH• RESISTORS
All resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable
• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , uPC... , µPC... ,uPD..., µPD...
When indicating parts by reference number,please include the board name.
• AbbreviationAR : Argentine modelAUS : Australian modelBR : Brazilian modelCH : Chinese modelCND : Canadian modelEE : East European modelHK : Hong Kong modelJ : Japanese modelJE : Tourist modelKR : Korea modelNE : North European modelRU : Russian model
5. REPAIR PARTS LIST
For the part of 51: TAPE, FFC FIXED (2-662-566-01) , cut WOVEN (T0.25),FABRIC NON (3-706-631-01) into the desired length and use it.
For the part of 58: TAPE, MOUNT PARTS FIXED (2-660-553-01) , cut SHEET, ADHESIVE (2-649-300-01) into the desired length and use it.
For the part of 68: HARNESS (HN-008) (1-963-980-11) and 71: HARNESS (HN-006) (1-963-978-11), cut HARNESS (HN-010) (1-964-232-11) into the desired length and use it.
For the part of 69: HARNESS (HN-009) (1-963-981-11) and 70: HARNESS (HN-007) (1-963-979-11), cut HARNESS (HN-011) (1-964-233-11) into the desired length and use it.
CAUTION1 :
CAUTION2 :
CAUTION3 :
CAUTION4 :
Language that can be selected about SY-145 board
Are
a
Eng
lish
Fre
nch
Ger
man
Spa
nish
Italia
n
Por
tugu
ese
Sim
plifi
edC
hine
se
Tra
ditio
nal
Chi
nese
Ara
bic
USGP2 CND
AUSVietnam
z
GP3AEP
z
z
z zUK
EBRHKCHKR
GP4 z
z
z
z
z
z
z
z z
z
Kor
ean
z
Rus
sian
z
Dut
ch
z
Tha
i
z
Per
sian
z
Sw
edis
h
z
Nor
weg
ian
z
Dan
ish
z
Fin
nish
z
Pol
ish
z
Cze
ch
z
Hun
garia
n
z
z
z z
5-3
5. REPAIR PARTS LIST5. REPAIR PARTS LIST
DSC-S600_L2
5-1-1. OVERALL SECTION
Ref. No. Part No. Description Ref. No. Part No. Description
ns : not supplied
1 2-599-475-31 SCREW (M1.7)2 2-660-555-01 COVER, USB3 X-2103-127-1 CABINET (REAR) ASSY4 2-660-525-01 SHEET, LCD COVER ADHESIVE5 2-660-556-01 COVER, LCD
6 X-2103-126-1 CABINET (FRONT) ASSY7 2-660-502-01 SCREW, TRIPOD8 3-080-204-11 SCREW, TAPPING, P2
9 A-1156-110-A LB-117 BOARD, COMPLETE10 1-964-236-11 HARNESS (HN-014)(WHITE)11 1-964-235-11 HARNESS (HN-013)(GRAY)12 1-964-234-11 HARNESS (HN-012)(YELLOW)13 A-1159-170-A BM-001 BOARD, COMPLETE
14 1-964-232-11 HARNESS (HN-010)(RED)15 1-964-233-11 HARNESS (HN-011)(BLACK)M001 1-763-818-51 DC MOTOR 8C-036G55
5-1. EXPLODED VIEWS
SY-145
A
C
A
D
B
B
C
E
D
E
Battery holder section(See page 5-4)
12
1
4
5
1
6
8
9
13814
15
1
7
ns
M001
ns
3
ns
1011
12
5-4
5. REPAIR PARTS LIST5. REPAIR PARTS LIST
DSC-S600_L2
5-1-2. BATTERY HOLDER SECTION
Ref. No. Part No. Description Ref. No. Part No. Description
51 Refar to page 5-1 CAUTION152 A-1156-105-A SY-145 BOARD, COMPLETE (SERVICE) (GP2)52 A-1156-106-A SY-145 BOARD, COMPLETE (SERVICE) (GP3)52 A-1156-107-A SY-145 BOARD, COMPLETE (SERVICE) (GP4)53 1-830-730-11 FLEXIBLE FLAT CABLE (FFC-056)54 1-830-731-11 FLEXIBLE FLAT CABLE (FFC-057)55 A-1156-109-A RL-063 BOARD, COMPLETE
* 56 2-670-904-01 SHEET (CCD), RADIATION57 A-1156-857-A LENS BLOCK ASSY (951A (C1))58 Refar to page 5-1 CAUTION259 1-788-228-12 UNIT, OPTICAL (G177)60 3-080-204-11 SCREW, TAPPING, P2
061 1-479-571-11 FLASH UNIT62 1-964-308-11 HARNESS (HN-015)64 X-2103-128-1 CABINET (UPPER) ASSY65 2-599-475-31 SCREW (M1.7)
* 66 2-660-550-01 HOLDER, MICROPHONE67 X-2103-129-1 HOLDER ASSY, BT
68 Refar to page 5-1 CAUTION369 Refar to page 5-1 CAUTION470 Refar to page 5-1 CAUTION471 Refar to page 5-1 CAUTION3
* 72 2-660-551-01 HOLDER, SP* 73 2-660-549-01 FRAME, LCD
74 2-633-989-01 GASKET (MS)75 A-1179-454-A SW-461 BOARD, COMPLE (SERVICE)76 1-830-732-11 FLEXIBLE FLAT CABLE (FFC-058)
* 77 2-670-905-01 SHEET (CON), RADIATION* 78 2-668-809-01 SHEET (FFC), RADIATION0BT001 1-756-539-21 BATTERY, LITHIUM SECONDARY0C9001 1-112-767-11 CAP, ELECT 180MF (330V)
LCD901 1-805-997-11 INDICATORMODULE, LIQUIDCRYSTALMIC901 1-542-676-11 MICROPHONESP901 1-826-347-11 SPEAKER (1.6CM)X001 1-760-840-11 VIBRATOR, CRYSTAL (32.768kHz)
SY-145
A
A
F
H
G
B
C
D
E
D
B
C
E
F
G
H
66
67
68
56
5777
606261
77
64 65
58
51
53
54
55
52
ns
MIC901
BT001
ns
X001
78
LCD901
SP90159
(24mm : RED)
69
72
(24mm : BLACK)
70(39mm : BLACK)
71
73
(39mm : RED)
(15mm × 5mm)
C9001
51(15mm × 5mm)
(5.5mm × 5.5mm)
(5.5mm × 5.5mm)58
76
75
74
60
: BT001 (Lithium battery) SW-461 board on the mount position. (See page 4-29)
• Refer to page 5-1 for mark 0.
ns : not supplied
CAUTION :Danger of explosion if battery is incorrectlyreplaced.Replace only with the same or equivalent type.
5-5
5. REPAIR PARTS LIST5. REPAIR PARTS LIST
DSC-S600_L2
Checking supplied accessories.
Make sure that the following accessories are supplied with your camcorder.
R6 (size AA) alkaline batteries (2)(not supplied)
Other accessories
2-666-673-01 CD-ROM (CYBER-SHOT APPLICATION SOFTWARE) (EXCEPT BR)
2-658-423-11 INSTRUCTION (READ THIS FIRST) (ENGLISH)(EXCEPT CH,KR,BR)2-658-423-21 INSTRUCTION (READ THIS FIRST) (FRENCH/ITALIAN)(CND,AEP)2-658-423-31 INSTRUCTION (READ THIS FIRST) (SPANISH/PORTUGUESE)(AEP,E)2-658-423-41 INSTRUCTION (READ THIS FIRST) (GERMAN/DUTCH)(AEP)2-658-423-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE/SIMPLIFIED CHINESE)(E,HK,CH)
2-658-423-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN)(AEP)2-658-423-71 INSTRUCTION (READ THIS FIRST) (ARABIC/PERSIAN)(E)2-658-423-81 INSTRUCTION (READ THIS FIRST) (KOREAN)(KR)2-658-423-91 INSTRUCTION (READ THIS FIRST) (CZECH/POLISH)(AEP)2-658-424-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN/SLOVAKIAN)(AEP)
2-658-424-21 INSTRUCTION (READ THIS FIRST) (SWEDISH/FINNISH)(AEP)2-658-424-31 INSTRUCTION (READ THIS FIRST) (NORWEGIAN/DANISH)(AEP)2-658-425-11 INSTRUCTION (USER’S GUIDE) (ENGLISH)(EXCEPT CH,KR,BR)2-658-425-21 INSTRUCTION (USER’S GUIDE) (FRENCH/ITALIAN)(CND,AEP)2-658-425-31 INSTRUCTION (USER’S GUIDE) (SPANISH/PORTUGUESE)(AEP,E)
2-658-425-41 INSTRUCTION (USER’S GUIDE) (GERMAN/DUTCH)(AEP)2-658-425-51 INSTRUCTION (USER’S GUIDE) (TRADITIONAL CHINESE/SIMPLIFIED CHINESE)(E,HK,CH)2-658-425-61 INSTRUCTION (USER’S GUIDE) (RUSSIAN)(AEP)2-658-425-71 INSTRUCTION (USER’S GUIDE) (ARABIC/PERSIAN)(E)2-658-425-81 INSTRUCTION (USER’S GUIDE) (KOREAN)(KR)
2-658-425-91 INSTRUCTION (USER’S GUIDE) (POLISH/CZECH)(AEP)2-658-426-11 INSTRUCTION (USER’S GUIDE) (HUNGARIAN/SLOVAKIAN)(AEP)2-658-426-21 INSTRUCTION (USER’S GUIDE) (SWEDISH/FINNISH)(AEP)2-658-426-31 INSTRUCTION (USER’S GUIDE) (NORWEGIAN/DANISH)(AEP)
USB cable (1)(Except BR model)1-827-038-11
Wrist strap (1)(Except BR model)2-050-981-01
5-6EDSC-S600_L2
Ref. No. Part No. Description Ref. No. Part No. Description5-2. ELECTRICAL PARTS LIST
A-1159-170-A BM-001 BOARD, COMPLETE***********************
************************************************************
A-1156-110-A LB-117 BOARD, COMPLETE**********************
< SWITCH >
* S101 1-786-480-41 SWITCH, PUSH (1 KEY) (OPEN)* S102 1-786-545-41 SWITCH, PUSH LEVER (S) (CLOSE)************************************************************
A-1156-109-A RL-063 BOARD, COMPLETE**********************
< DIODE >
D201 6-501-030-01 DIODE SML-412MWT86 (POWER)LED901 6-500-505-01 DIODE OPY5052 (AF)
< SWITCH >
* S201 1-786-912-21 TACTILE SWITCH (SHUTTER)S202 1-786-885-21 SWITCH, TACTILE (POWER)
************************************************************
A-1179-454-A SW-461 BOARD, COMPLETE (SERVICE)********************************
1-830-732-11 FLEXIBLE FLAT CABLE (FFC-058)0BT001 1-756-539-21 BATTERY, LITHIUM SECONDARY
not supplied SW-461 BOARD, COMPLETE***********************(SW-461 board is included in the COMPLETE of
SW-461 board (SERVICE).)
< CAPACITOR >
C001 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC003 1-164-943-81 CERAMIC CHIP 0.01uF 10% 16V
< CONNECTOR >
* CN001 1-766-644-51 CONNECTOR, FFC/FPC 8PCN002 1-817-827-11 MEMORY STICK DUO CONNECTORCN003 1-794-962-11 CONNECTOR, SQUARE TYPE (USB 5P) (USB)
* CN006 1-818-087-51 CONNECTOR, FFC/FPC (LIF) 26P
< DIODE >
D001 8-719-077-34 DIODE SML-310YTT86 (FLASH)D002 8-719-075-29 DIODE SML-510MWT86S (AE LOCK)D003 6-500-817-01 DIODE SML-512UWT86 (ACCESS)D004 6-500-776-01 DIODE MAZW068H0LS0D005 8-719-056-54 DIODE MAZS068008SO
< FERRITE BEAD >
* FB001 1-481-021-21 INDUCTOR, FERRITE BEAD (1005)* FB002 1-481-021-21 INDUCTOR, FERRITE BEAD (1005)* FB003 1-481-021-21 INDUCTOR, FERRITE BEAD (1005)* FB004 1-481-021-21 INDUCTOR, FERRITE BEAD (1005)
FB005 1-400-331-11 FERRITE, EMI (SMD) (1005)
FB006 1-400-331-11 FERRITE, EMI (SMD) (1005)FB007 1-400-331-11 FERRITE, EMI (SMD) (1005)
< LINE FILTER >
LF001 1-456-583-11 COMMON MODE CHOKE COIL
< RESISTOR >
R001 1-218-935-11 RES-CHIP 33 5% 1/16WR007 1-218-953-11 RES-CHIP 1K 5% 1/16WR008 1-218-953-11 RES-CHIP 1K 5% 1/16WR009 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR012 1-218-953-11 RES-CHIP 1K 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB001 1-234-376-11 RES, NETWORK 2.2K (1005X4)RB002 1-234-376-11 RES, NETWORK 2.2K (1005X4)RB003 1-234-376-11 RES, NETWORK 2.2K (1005X4)
< SWITCH >
S001 1-786-885-21 SWITCH, TACTILE (DOWN)S002 1-786-885-21 SWITCH, TACTILE (UP)S003 1-786-885-21 SWITCH, TACTILE (SET)S004 1-786-885-21 SWITCH, TACTILE (RIGHT)S005 1-786-885-21 SWITCH, TACTILE (LEFT)
S006 1-786-885-21 SWITCH, TACTILE (ZOOM T)S007 1-786-885-21 SWITCH, TACTILE (DISPLAY)S008 1-786-885-21 SWITCH, TACTILE (MENU)S009 1-786-885-21 SWITCH, TACTILE (DUST)S010 1-786-885-21 SWITCH, TACTILE (ZOOM W)
* S011 1-786-947-11 SIGNAL SELECTOR SWITCH(MOVIE/STILL/PLAY)
************************************************************
SY-145 BOARD, COMPLETE**********************
************************************************************
• Refer to page 5-1 for mark 0.
BM-001 LB-117 RL-063 SW-461 SY-145
Electrical parts list of the SY-145 board is notshown.Pages from 5-7 to 5-10 are not shown.
Sony EMCS Co.
2006G1600-1 ©2006.07
Published by Kohda TEC9-876-922-82
SERVICE MANUAL
SUPPLEMENT-1File this supplement-1 with the service manual.
(DI06-040)
• Change of SW-461 board suffix number• Change of printed wiring boards• Change of repair parts list
Ver. 1.1 2006. 07
DSC-S600_L2
US ModelCanadian Model
AEP ModelUK Model
E ModelAustralian Model
Chinese ModelBrazilian Model
Hong Kong ModelKorea Model
LEVEL 2
DSC-S600
— 2 —DSC-S600_L2
Page
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS4-3. PRINTED WIRING BOARDS : Changed portion
Suffix -11 Suffix -12
4-29,4-30
SW-461 BOARD (SIDE A)
SW-461 BOARD (SIDE B)
• Change of SW-461 board suffix number
10 1
126
CN002
CN006
C001
FB001FB002
FB003FB004FB005 R001R008
10 1
126
CN002
CN006
C001
FB001FB002
FB003FB004FB005 R001R008
1
6
CN00
3
1-867-292- 11
(USB)
15
6
CN00
3
1-867-292- 12
(USB)
1
2
3
4
12
34
1
2
3
4
12
34
1 2
3 412
34
178
2
1 782 17
8 2
123
1 2
3 4
1 2
3 4
AK
S001
DOWN
SETRIGHT LEFT
MENU
UP
DUST DISPLAY
S002
S003
S004 S0
05
S007
S008
S009
D003
(A
CCES
S)
D004
D005
D006
D007
RB00
1
RB002
RB003
R007 R015
1
2
3
4
12
34
1
2
3
4
12
34
1 2
3 412
34
178
2
1 782 17
8 2
123
1 2
3 4
1 2
3 4
AK
S001
DOWN
SETRIGHT LEFT
MENU
UP
DUST DISPLAY
S002
S003
S004 S0
05
S007
S008
S009
D003
(A
CCES
S)
D004
D005
D006
D007
RB00
1
RB002
RB003
R007 R015
1 2LF001
LND0
37
LND0
38
LND0
39LN
D040
LND0
41FB007
R012
1-867-292-
11
1 2LF001
LND0
37
LND0
38
LND0
39LN
D040
LND0
41FB007
R012
1-867-292-
12
— 3 —DSC-S600_L2
4-3. PRINTED WIRING BOARDS
• Change of printed wiring boards
Page
: Added portion
Before change After change
4-27
BM-001 BOARD
LB-117 BOARD
RL-063 BOARD
4-28
M
LND401 LND402
LND403
LND404
M001(LENS BARRIER)
1-868-243-11
M
LND401 LND402
LND403
LND404
M001(LENS BARRIER)
1-868-243-11 12
S10
1-867-722-11ARRIER
SE
S10
1-867-722-11 12ARRIER
SE
1
2WERWER
LND2
08
LED901(AF LED)
LND2
09
11
1
2WERWER
LND2
08
LED901(AF LED)
LND2
09
11 12
— 4 —DSC-S600_L2
• Change of repair parts list
Page
64 X-2103-128-2 CABINET (UPPER) ASSY64 X-2103-128-1 CABINET (UPPER) ASSY
Ref. No. Part No. DescriptionRef. No. Part No. Description
5. REPAIR PARTS LIST5-1. EXPLODED VIEWS : Changed portion : Added portion
Before change After change
5-4
5-1-2. BATTERY HOLDER SECTION
2-666-673-01 CD-ROM (CYBER-SHOT APPLICATION SOFTWARE)(EXCEPT BR, US)
2-699-461-01 CD-ROM (CYBER-SHOT APPLICATION SOFTWARE)(US)
2-666-673-01 CD-ROM (CYBER-SHOT APPLICATION SOFTWARE)(EXCEPT BR)
X X
Checking supplied accessories.
Other accessories
5-5
Page
S202 1-786-885-41 SWITCH, TACTILE (POWER)S202 1-786-885-21 SWITCH, TACTILE (POWER)
Ref. No. Part No. DescriptionRef. No. Part No. Description
Before change After change
5-6E
RL-063 BOARD
5-2. ELECTRICAL PARTS LIST : Changed portion
S001 1-786-885-41 SWITCH, TACTILE (DOWN)S002 1-786-885-41 SWITCH, TACTILE (UP)S003 1-786-885-41 SWITCH, TACTILE (SET)S004 1-786-885-41 SWITCH, TACTILE (RIGHT)S005 1-786-885-41 SWITCH, TACTILE (LEFT)
S006 1-786-885-41 SWITCH, TACTILE (ZOOM T)S007 1-786-885-41 SWITCH, TACTILE (DISPLAY)S008 1-786-885-41 SWITCH, TACTILE (MENU)S009 1-786-885-41 SWITCH, TACTILE (DUST)S010 1-786-885-41 SWITCH, TACTILE (ZOOM W)
S001 1-786-885-21 SWITCH, TACTILE (DOWN)S002 1-786-885-21 SWITCH, TACTILE (UP)S003 1-786-885-21 SWITCH, TACTILE (SET)S004 1-786-885-21 SWITCH, TACTILE (RIGHT)S005 1-786-885-21 SWITCH, TACTILE (LEFT)
S006 1-786-885-21 SWITCH, TACTILE (ZOOM T)S007 1-786-885-21 SWITCH, TACTILE (DISPLAY)S008 1-786-885-21 SWITCH, TACTILE (MENU)S009 1-786-885-21 SWITCH, TACTILE (DUST)S010 1-786-885-21 SWITCH, TACTILE (ZOOM W)
SW-461 BOARD
Sony EMCS Co.
2007J0800-1 ©2007.10
Published by Kohda TEC9-876-922-85
SERVICE MANUAL
DSC-S600_L2
LEVEL 2
DSC-S600
SUPPLEMENT-2File this supplement-2 with the service manual.
(DI07-130)
Subject :• Notes on Repairig Cabinet
(Rear) Assy or Frame, LCD
US ModelCanadian Model
AEP ModelUK Model
E ModelAustralian Model
Chinese ModelBrazilian Model
Hong Kong ModelKorea Model
Ver. 1.2 2007. 10
There are two kinds of Cabinet (Rear) Assy and Frame, LCD.On repairing them, please refer to next page for details.
— 2 —DSC-S600_L2
C
B
41
3
AB
1
71
73
(39mm : RED)
4
Function Button in Type B
Type A Type B
Type 1
Cabinet (Rear) Assy
Frame, LCD
Type 2
Cut red points at an angle (bold lines)as shown below.
• In case of NG, cut the red points of function button section in the cabinet (rear) assy Type B as shown below.
• The Different Points
FRAME, LCD
CABINET (REAR) ASSY Type 1 Type 2
• Type A OK OK
• Type B NG OK
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Printing a text1. Click the Print button .2. Specify a printer, print range, number of copies, and other op-
tions, and then click [OK].
Application of printing:To set a range to be printed within a page, select the graphic
selection tool and drag on the page to enclose a range tobe printed, and then click the Print button.
Finding a text1. Click the Find button .2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary)
Application to the Service Manual:To execute “find” from current page toward the previous pages,select the check box “Find Backward” and then click the“Find”.
3. Open the find dialog box again, and click the [Find Again] andyou can find the matched character strings displayed next.(Character strings entered previously are displayed as they arein the text box.)
Application to the Service Manual:The parts on the drawing pages (block diagrams, circuit dia-grams, printed circuit boards) and parts list pages in a textcan be found using this find function. For example, find aRef. No. of IC on the block diagram, and click the [Find Again]continuously, so that you can move to the Ref. No. of IC onthe circuit diagram or printed circuit board diagram succes-sively.Note: The find function may not be applied to the Service
Manual depending on the date of issue.
Switching a page• To move to the first page, click the .
• To move to the last page, click the .
• To move to the previous page, click the .
• To move to the next page, click the .
Reversing the screens displayed once• To reverse the previous screens (operation) one by one, click
the .
• To advance the reversed screens (operation) one by one, click
the .
Application to the Service Manual:This function allows you to go and back between circuit dia-gram and printed circuit board diagram, and accordingly itwill be convenient for the voltage check.
Moving with link
1. Select either palm tool , zoom tool , text selection tool
, or graphic selection tool .2. Place the pointer in the position in a text where the link exists
(such as a button on cover and the table of contents page, orblue characters on the removal flowchart page or drawingpage), and the pointer will change to the forefinger form .
3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:Click an item (text) on the bookmark pallet, and you can moveto the link destination. Also, clicking can display thehidden items.(To go back to original state, click )
Zooming or rotating the screen display“Zoom in/out”• Click the triangle button in the zoom control box to select the
display magnification. Or, you may click or for zoom-
ing in or out.
“Rotate”• Click rotate tool , and the page then rotates 90 degrees each.
Application to the Service Manual:The printed circuit board diagram you see now can be changedto the same direction as the set.
Toolbar
Revision History
DSC-S600_L2
Ver.
1.0
1.1
1.2
Date
2005.12
2006.07
2007.10
History
Official Release
Supplement-1(DI06-040)
Supplement-2(DI07-130)
Contents
—
• Change of SW-461 board suffix number• Change of printed wiring boards• Change of repair parts list
• Notes on Repairig Cabinet (Rear) Assy orFrame, LCD
S.M. Rev.issued
—
No
No
Reverse 987692233.pdf