SolidWorks V8 engine tutor
-
Upload
beata-kublik -
Category
Documents
-
view
55 -
download
7
description
Transcript of SolidWorks V8 engine tutor
![Page 1: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/1.jpg)
© Aykut Dana, GrabCad.com, 2012
Connecting Rodfile: connecting rod
1 Step 1
2 draw two circles like shown on the front plane
3
4 Step 2
5 add two tangent line
6
![Page 2: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/2.jpg)
7 Step 3
8 add two more circle
9
10 Step 4
11 draw a line and mirror it
12
13 Step 5
14 draw a centerline and use trim command
![Page 3: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/3.jpg)
15
16 Step 6
17 use fillet command like shown
18
19 Step 7
20 go up side and use trim command
21
22 Step 8
23 use fillet command again
![Page 4: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/4.jpg)
24
25 Step 9
26 extrude the sketch in two directions. (5,5 mm for each way, total 11mm)
27
28 Step 10
29 open a sketch on the body and draw a line. make parallel the line with the shown edge
![Page 5: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/5.jpg)
30
31 Step 11
32 mirror the line and add this two circle
33
34 Step 12
35 Intersect the lines and use trim command
![Page 6: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/6.jpg)
36
37 Step 13
38 use trim command and mirror it
39
40 Step 14
41 draw two circles and cut the body
![Page 7: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/7.jpg)
42
43 Step 15
44 draw two circles more and cut the body again. use offset feature
45
46 Step 16
47 draw a sketch on the body like shown
![Page 8: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/8.jpg)
48
49 Step 17
50 extrude it 2mm and use mirror command
51
52 Step 18
53 now use fillet command
![Page 9: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/9.jpg)
54
55 Step 19
56 your connecting rod is ready to use ( create a folder and save into it, firstly we will generate the V12 engine parts )
57
58 Step 20
59 from Luis :)
![Page 10: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/10.jpg)
60
connecting rod part 2
1 Step 1
2 open sketch on the front plane and draw shown sketch
3
4 Step 2
5 use trim command
![Page 11: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/11.jpg)
6
7 Step 3
8 add a circle
9
10 Step 4
11 add two line
![Page 12: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/12.jpg)
12
13 Step 5
14 use trim command
15
16 Step 6
17 extrude the body in two directions
![Page 13: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/13.jpg)
18
19 Step 7
20 draw shown sketch on the body
21
22 Step 8
23 extrude it like this
![Page 14: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/14.jpg)
24
25 Step 9
26 draw the shown sketch and cut the body
27
28 Step 10
29 use fillet command
![Page 15: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/15.jpg)
30
31 Step 11
32 your part is ready to use
33
● crank
a Step 1b open a sketch on the right plane and draw a sketch like shown
![Page 16: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/16.jpg)
c
d Step 2e open a sketch on the body. draw a 30mm radiused circle and extrude it 20mm
f
g Step 3h use revolve command
![Page 17: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/17.jpg)
i
j Step 4k go to other side draw shown sketch and extrude it 20 mm
l
m Step 5n open a sketch on same surface and draw shown skecth
![Page 18: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/18.jpg)
o
p Step 6q use cut extrude command and tick 'filp side to cut'
r
s Step 7t now use mirror command. your crank began to take shape
![Page 19: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/19.jpg)
u
v Step 8w use move copy body command. enter volues
x
y Step 9z rotate this (4th from right side) body 60degree
![Page 20: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/20.jpg)
aa
bb Step 10cc rotate 3th body 120 degree
dd
ee Step 11ff rotate sixth body 180 degree
![Page 21: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/21.jpg)
gg
hh Step 12ii rotate second body 240 degree
jj
kk Step 13ll rotate 5th body 300 degree
![Page 22: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/22.jpg)
mm
nn Step 14oo use combine command. your crank is ready for now. we will add oil canal and other parts after
pp
● It worked (31) Not helpful (0) Comment (5)
●● Aykut Dana 4 months ago
● How to use combine command
● Only if you have problem with the combine command, follow this tutorial. if not, go to part 4.
![Page 23: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/23.jpg)
a Step 1b click on the ''solid bodies''. As you see there are six bodies. We will combine them
c
d Step 2e select all bodies
f
g Step 3h right click and then select combine command
![Page 24: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/24.jpg)
i
j Step 4k make ticked the shown area
l
m Step 5n confirm that. we have one solid body now
![Page 25: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/25.jpg)
o
● It worked (7) Not helpful (0) Add comment
●● Aykut Dana 5 months ago
● Aykut Dana 5 months ago● using 'move copy body' command for coping
● (if you have a problem with this command, follow the tutorial. if not, go to next part)
1 Step 1
2 follow the steps up to here
3
![Page 26: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/26.jpg)
4 Step 2
5 click on options--customize
6
7 Step 3
8 find this command
9
10 Step 4
11 drag and drop the command on the command manager
![Page 27: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/27.jpg)
12
13 Step 5
14 click on the command
15
16 Step 6
17 use this button
![Page 28: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/28.jpg)
18
19 Step 7
20 select the body
21
22 Step 8
23 make the copy box ticked and enter 5
![Page 29: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/29.jpg)
24
25 Step 9
26 now we will change z coordinate. enter the shown value (95mm)
27
28 Step 10
29 confirm that and replicated body is ready.
![Page 30: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/30.jpg)
30●
Crank connection points
1 Step 1
2 open a sketch on the top plane and draw shown sketch
3
4 Step 2
5 use revolve command
![Page 31: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/31.jpg)
6
7 Step 3
8 open a sketch on top planen again and draw an axis for revolve command
9
10 Step 4
11 draw shown sketch
![Page 32: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/32.jpg)
12
13 Step 5
14 use revolve command
15
16 Step 6
17 thats is all for now
![Page 33: SolidWorks V8 engine tutor](https://reader033.fdocuments.us/reader033/viewer/2022061109/545235c0b1af9f83248b4e18/html5/thumbnails/33.jpg)
18