Solidworks Tutorial For Beginner

download Solidworks Tutorial For Beginner

of 104

Transcript of Solidworks Tutorial For Beginner

  • 8/13/2019 Solidworks Tutorial For Beginner

    1/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    2/104

    i

    Foreword

    The main objective of these tutorials is to give you a kick start using SolidWorks. The approach to

    write this tutorial is based on what is the most important knowledge you should know and what is

    commonly tool used. You will learn step by step by working on it. These tutorials will teach you

    the basic skills of using Solidworks in your daily design works. Even this tutorials didnt have fullexplanations of tools that Solidworks have but dont worry you will master it along the way, as I

    did.

    If you have any questions about these tutorials, drop your mail to

    [email protected]

    Solidworks 2010 Tutorials: Beginner

    http://www.solidworkstutorials.com

    2010 solidworkstutorials.com , All rights reserved.

    This publication is copyright under the solidworkstutorials.com

    All rights reserved. Apart from any fair dealing for the purpose of private study, research, criticism, or review, as permitted

    under the Copyright Designs and Patents Act 1988, no part may be reproduced, stored

    in a retrieval system, or transmitted in any form or by any means, electronic, electrical, chemical, mechanical,photocopying, recording or otherwise, without the prior permission of the copyright owners. Unlicensed multiple copying

    of this publication is illegal. Inquiries should be addressed to: [email protected]

    If this guide is distributed with software that includes an end-user agreement, this guide, as well as the software described

    in it, is furnished under license and may be used or copied only in accordance with the terms of such license. Except as

    permitted by any such license, no part of this guide may be reproduced, stored in a retrieval system, or transmitted, in any

    form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of

    solidworkstutorials.com. Please note that the content in this guide is protected under copyright law even if it is not

    distributed with software that includes an end-user license agreement. The content of this guide is furnished for

    informational use only, is subject to change without notice, and should not be construed as a commitment by

    solidworkstutorials.com. Solidworkstutorials.com assumes no responsibility or liability for any errors or inaccuracies that

    may appear in the informational content contained in this guide. Please remember that existing artwork or images that

    you may want to include in your project may be protected under copyright law. The unauthorized incorporation of such

    material into your new work could be a violation of the rights of the copyright owner. Please be sure to obtain anypermission required from the copyright owner. Any references to company names in sample templates are for

    demonstration purposes only and are not intended to refer to any actual organization.

    The publishers are not responsible for any statement made in this publication. Data, discussion, and conclusions

    developed by the Author are for information only and are not intended for use without independent substantiating

    investigation on the part of the potential users. Opinions expressed are those of the Author and are not necessarily those

    of the Institution of Mechanical Engineers or its publishers.

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    3/104

    Solidworks Tutorials: Beginner Table of contents www.solidworkstutorials.com

    Solidworks Tutorials: Beginner Table of contents ii

    Table of contents

    Beginner Part 1: My First Solid 1

    The big picture how SolidWorks works, it starts

    with a simple editable sketch. From this sketch a

    feature build the solid. From this solid itproduces drawing...

    Beginner Part 2: Sketching 10

    Sketch is the base of your part, its a good

    practice to master sketching in SolidWorks...

    Beginner Part 3: Turning Parts 23

    Some parts such as pins and shafts can be

    manufacture by turning process on lathe

    machine, we can create turning part by revolving

    it sketch on it axis...

    Beginner Part 4: Hole Wizard 30

    Hole Wizard is used for creating predefined and

    standard holes such as counter bore hole,

    counter sunk hole, screw clearance hole and

    many more...

    Beginner Part 5: Pattern 40

    Pattern (or some called array) is used to repeat

    features in linear arrangement or circular

    arrangement. Its good to know how to optimize

    these tool, it help you make your part faster and

    easier...

    Beginner Part 6: Assembly Parts 60

    Assembly is a part of design process, it show how

    all designed parts work together as a single

    unit...

    Beginner Part 7: Detailing Drawing 80

    Once solid parts created we need to transfer it to

    engineering drawing so the others can

    understand your parts

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    4/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 1

    Beginner Part 1: My First Solid

    The big picture how SolidWorks works, it starts with a simple

    editable sketch. From this sketch a feature build the solid. From

    this solid it produces drawing... Lets begin your first solid...

    1. Click New , click Part , OK.

    2. Click Front Plane, insert sketch on plane by click Sketch.

    3. Click Sketch , click

    Corner Rectangular . Start first point at origin and

    click another point at top right side.

    4. Click Smart Dimension , click top edge set

    dimension to 3inand click right edge set dimension to 2in.

    In this tutorial you will make this

    bracket, start from sketch and build

    features.

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    5/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 2

    5. To build features, click Extruded Boss/Base , set D1to

    0.10in and .

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    6/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 3

    6. Click on front face of the part, click Normal To.

    7. Click Circle , sketch circle on face

    .

    Click Smart Dimension , click circle edge and set

    diameter to 0.6in. For circle positioning click circle edge and

    vertical part edge set to 0.5in. Click circle edge again and

    click horizontal part edge set to 0.5in.

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    7/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 4

    8. Click Extruded Cut , change Direction 1to Through

    All and .

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    8/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 5

    9. Click on front face and select Sketch

    .

    Select Corner Rectangular sketch rectangular from

    top right edge to center.

    10. Click Smart Dimension , set rectangular

    dimension to 2inand 1in.

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    9/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 6

    Click

    Extruded Cut and select Through All

    and .

    11. Click on front face and select Sketch

    . Click

    Corner Rectangular and sketch rectangular start

    form bottom left edge to right edge.

  • 8/13/2019 Solidworks Tutorial For Beginner

    10/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 7

    Click

    Smart Dimensionand set rectangular height to 0.1in.

    12. Click Extruded Boss/Base set Direction 1 to 0.5in

    and . Click Display

    Styleand select Isometric.

  • 8/13/2019 Solidworks Tutorial For Beginner

    11/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 8

    13. Click Fillet , check Full preview

    add fillet to all edges

  • 8/13/2019 Solidworks Tutorial For Beginner

    12/104

    Beginner Part 1: My First Solid www.solidworkstutorials.com

    Beginner Part 1: My First Solid 9

    and

    .

    14. Save the part as Bracket and youre done! Simple isntit?

    Go to table of contents

    Go to beginning of chapter tutorial

    Go to www.solidworkstutorials.com

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    13/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 10

    Beginner Part 2: Sketching

    Sketch is the base of your part, its a good practice to master

    sketching in SolidWorks...

    1. Click New , click Part , OK.

    2. Click Front Plane, insert sketch on plane by click Sketch.

    3. Click Sketch , click

    Corner Rectangular . Start first point at origin and

    click another point at top right side.

    4. Click Smart Dimension , click top edge set

    dimension to 2inand click right edge set dimension to 2in.

    In this tutorial you will make this

    box, start from sketch and build

    features. Youll learn how to use

    sketch tools to build this part.

  • 8/13/2019 Solidworks Tutorial For Beginner

    14/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 11

    5. To build features, click Features>Extruded Boss/Base

    , set D1to 0.50in

    and .

  • 8/13/2019 Solidworks Tutorial For Beginner

    15/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 12

    6. Click on front face of the part, click Normal To.

    7. Click on front face and click Sketch.

  • 8/13/2019 Solidworks Tutorial For Beginner

    16/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    17/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 14

    10. Click on side face, click Sketch.

    11. While pressing Ctrlkey select inner left and right edge.

    Click

    Convert Entities .

    12. Select Centerline from line menu ,

    sketch a centerline midpoint to midpoint of both converted

  • 8/13/2019 Solidworks Tutorial For Beginner

    18/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 15

    edges.

    13. Click sketched centerline

    and click Offset Entities.

  • 8/13/2019 Solidworks Tutorial For Beginner

    19/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 16

    Set Parameter, D to 0.3incheck Bi-directionaland .

    14. Now click Trim Entities to remove excess line,

    before make any cut make sure under option Trim to

    closestis selected. Trim extra line as

    below sketch. Answers Yesif notification appear.

    15. Click View Orientation>Isometric.

    16. Click Features>Extruded Boss/Base , for Direction 1,

    click Reverse Direction(green box) and set D1to 0.1in.

  • 8/13/2019 Solidworks Tutorial For Beginner

    20/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 17

    and .

  • 8/13/2019 Solidworks Tutorial For Beginner

    21/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 18

    17. Click on front face and click Normal To.

    18. Click on front face and click Sketch.

  • 8/13/2019 Solidworks Tutorial For Beginner

    22/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 19

    19. Click Circle, sketch circle at left edge.

    20. Click Smart Dimension, dimension sketch as

    below sketch.

    21. Click on sketched circle, click

    Copy Entities. Set delta x

  • 8/13/2019 Solidworks Tutorial For Beginner

    23/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 20

    to 0.3in and .

    22. Click Centerline, sketch centerlineacross front face and make sure it starts at midpoint left edge

    and midpoint right edge and .

    23. While press Ctrlkey, select both sketched circle and click

    Mirror Entities , on Mirror Optionclick

    Mirror about:box, and select centerline

  • 8/13/2019 Solidworks Tutorial For Beginner

    24/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 21

    and .

    24. Click Extruded Cut, and set D1to 0.1in

    and .

    25. Click View Orientation>Back,

  • 8/13/2019 Solidworks Tutorial For Beginner

    25/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 22

    and click on back face and click Sketch.

    26. Click Sketch>Circle, sketch circle at lower left edge.

    Click Smart

    Dimension and dimension sketched circle as

    sketch below.

    and .

  • 8/13/2019 Solidworks Tutorial For Beginner

    26/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 23

    27. Click on sketched circle, and click

    Linear Sketch Pattern and on

    Direction 1set D1to 1.2inand on Direction 2, change #to

    2and set D2to 1.2inand .

  • 8/13/2019 Solidworks Tutorial For Beginner

    27/104

    Beginner Part 2: Sketching www.solidworkstutorials.com

    Beginner Part 2: Sketching 24

    28. Click Features>Extruded Cut, and set direction to

    Through All and .Click View Orientation>Isometric.

    29. Save the part as Sketch and youre done! Simple isnt

    it?

    Go to table of contents

    Go to beginning of chapter tutorial

    Go to www.solidworkstutorials.com

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    28/104

    Beginner Part 3: Turning Part www.solidworkstutorials.com

    Beginner Part 3: Turning Part 25

    Beginner Part 3: Turning Part

    Some parts such as pins and shafts can be manufacture by

    turning process on lathe machine, we can create turning part by

    revolving it sketch on it axis...

    1. Click New, click Part, OK.

    2. Click Front Plane, insert sketch on plane by click Sketch.

    3. Click on Line, sketch a closed loop start at origin, sketch

    as sketch below end back at origin.

    and

    4. Click Smart Dimension and dimension sketch as

    sketch below.

    and .

    5. Click Features>Revolved Boss/Base,and click on bottom line as it axis.

    In this tutorial you will make this

    pin, start from sketch and build

    solid body by revolve it sketch on

    axis. Youll learn how to use

    revolved boss/base and revolved

    cut to build this part.

  • 8/13/2019 Solidworks Tutorial For Beginner

    29/104

    Beginner Part 3: Turning Part www.solidworkstutorials.com

    Beginner Part 3: Turning Part 26

    and .

    6. Click View Orientation>Front

    and click Front Planeand click Sketch.

  • 8/13/2019 Solidworks Tutorial For Beginner

    30/104

    Beginner Part 3: Turning Part www.solidworkstutorials.com

    Beginner Part 3: Turning Part 27

    7. Click Corner Rectangle, and sketch rectangle overlap

    on solid body as sketched below.

    and .

    8. Click Smart Dimension and dimension sketch as

    sketched below.

    9. To view solid body axis, click View>Temporary Axes.

    10. To make second undercut, click Features>Revolved Cut

    and select temporary axes as it axis

  • 8/13/2019 Solidworks Tutorial For Beginner

    31/104

    Beginner Part 3: Turning Part www.solidworkstutorials.com

    Beginner Part 3: Turning Part 28

    and .

  • 8/13/2019 Solidworks Tutorial For Beginner

    32/104

    Beginner Part 3: Turning Part www.solidworkstutorials.com

    Beginner Part 3: Turning Part 29

    11. To hide temporary axes, click View>Temporary Axes.

    12. Save the part and youre done! Simple isnt it?

    Go to table of contents

    Go to beginning of chapter tutorial

    Go to www.solidworkstutorials.com

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    33/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 30

    Beginner Part 4: Hole Wizard

    Hole Wizard is used for creating predefined and standard holes

    such as counter bore hole, counter sunk hole, screw clearance

    hole and many more...

    1. Click New, click Part, OK.

    2. Click Top Plane, insert sketch on plane by click Sketch.

    3. Click on Corner Rectangle, sketch a rectangle start at

    origin.

    and .

    4. Click Smart Dimension and dimension sketch as

    sketch below.

    and .

    5. Click Features>Extruded Boss/Base, on Direction 1

    set D1to 1in

    In this tutorial you will add

    counterbore, countersink and tap

    holes to this plate by using Hole

    Wizard tools.

  • 8/13/2019 Solidworks Tutorial For Beginner

    34/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 31

    and .

    6. Click on top face and click Normal To.

    7. Click Features>Hole Wizard on Hole Type, select

    Counterbore, Standardto Ansi Inch, Typeto Socket Head

    Cap Screw, Sizeto #10, Fitto Normaland End Condition

    to Through All.

  • 8/13/2019 Solidworks Tutorial For Beginner

    35/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 32

    For positions placement for this counterbore hole, click on

    Positionstab. Now click three

    more positions at each edge.

  • 8/13/2019 Solidworks Tutorial For Beginner

    36/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 33

    8. Click on Smart Dimensions, click on center point

    of counterbore hole and click left edge, set dimension to

    0.5in.

    Continue dimensioning as sketched below.

    and .

    9. For adding countersink at center, click on top faceand click

    on Hole Wizard .

  • 8/13/2019 Solidworks Tutorial For Beginner

    37/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 34

    On Hole Type, select Countersink, Standardto Ansi Inch,

    Typeto Flat Head Screw (100), Sizeto #10, Fitto Normal

    and End Conditionto Through All.

    10. For positions placement for this countersink holes, click on

    Positionstab. Now click three

    more positions at center.

  • 8/13/2019 Solidworks Tutorial For Beginner

    38/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 35

    11. Click on Smart Dimensions, click on center point

    of countersink hole and click left edge, set dimension to

    2.5in.

    Continue dimensioning as sketched below.

    and .

    12. For adding center tap hole, click on top face at center and

    click Hole Wizard.

  • 8/13/2019 Solidworks Tutorial For Beginner

    39/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 36

    On Hole Type, select Tap, Standardto Ansi Inch, Typeto

    Tapped hole, Sizeto 1/2-13, End Conditionto Through

    All.

    13. For positions placement for this tap hole, click on Positions

    tab. There is another style to

    positions hole wizard is define it position by sketch, let try it.

    Click on Centerline, Sketch a

    horizontal line start at midpoint of left edge to midpoint left

  • 8/13/2019 Solidworks Tutorial For Beginner

    40/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 37

    edge. Press Escto end sketch centerline.

    14. Click and drag tap center to midpoint of centerline.

    and .

    15. Click View Orientation>Isometric. Done.

  • 8/13/2019 Solidworks Tutorial For Beginner

    41/104

    Beginner Part 4: Hole Wizard www.solidworkstutorials.com

    Beginner Part 4: Hole Wizard 38

    16. Save the part as Plate1 and youre done! Simple isnt it?

    Go to table of contents

    Go to beginning of chapter tutorial

    Go to www.solidworkstutorials.com

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    42/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    43/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 40

    and .

    6. Click on top faceand click Normal To.

    7. Click on top faceand click Sketch.

  • 8/13/2019 Solidworks Tutorial For Beginner

    44/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 41

    Click on Circle and sketch a circle on top face and .

    8. Click on Smart Dimension and dimension

    sketched circle as sketch below.

    9. Click Features>Extruded Cut on Direction 1set to

    Through All. and .

    10. Click Features>Hole Wizard on Hole Type, select

    Counterbore, Standardto Ansi Inch, Typeto Socket Head

    Cap Screw, Sizeto #10, Fitto Normaland End Condition

    to Through All.

  • 8/13/2019 Solidworks Tutorial For Beginner

    45/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 42

    For positions placement for this counterbore hole, click on

    Positionstab. Click one point

    at lower left edge.

  • 8/13/2019 Solidworks Tutorial For Beginner

    46/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 43

    11. Click on Smart Dimension and dimension

    sketched circle as sketch below.

    and .

    12. To pattern this counterbore hole, click on CBORE for #10

    Socket Head Cap Screw1

    and click Linear Pattern. Click on bottom edge as

    Direction 1pattern.

  • 8/13/2019 Solidworks Tutorial For Beginner

    47/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 44

    Set D1to 2.5inand pattern # to 3. Click on highlighted

    arrowto switch it directions.

    13. Click on left edgeas Direction 2pattern.

    Set D2to 3.4inand number of pattern #to 2. You can click

  • 8/13/2019 Solidworks Tutorial For Beginner

    48/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    49/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 46

    Click Smart Dimension, set circle diameter to

    1.5in.

    15. Click Line, sketch a vertical line crossing sketch circle at

    12 oclock to 6 oclock.

    Press Esckey to end Line. Exit sketch.

    16. Click on Hole Wizard, on Hole Typeclick on Tap,Standard: Ansi Inch, Type: Tapped Hole, Hole

    Specifications Size:1/4-20, End Condition Through All.

  • 8/13/2019 Solidworks Tutorial For Beginner

    50/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 47

    For positions placement for this tap hole, click on Positions

    tab. Click one point at 12

    oclock last sketched circle.

  • 8/13/2019 Solidworks Tutorial For Beginner

    51/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 48

    and .

    17. To hide guide sketch, click Sketch4and click Hide.

    18. To pattern tap hole, click on 1/4-20 Tapped Hole1

    and click Circular Pattern.

    Change view to isometric by click on View

    Orientation>Isometric

    Click on open inner hole faceas its pattern axis, set

    instances #to 6and .

  • 8/13/2019 Solidworks Tutorial For Beginner

    52/104

    Beginner Part 5: Pattern www.solidworkstutorials.com

    Beginner Part 5: Pattern 49

    19. Save the part as Blockand youre done! Simple isnt it?

    Go to table of contents

    Go to beginning of chapter tutorial

    Go to www.solidworkstutorials.com

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    53/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 50

    Beginner Part 6: Assembly Parts

    Assembly is a part of design process, it show how all designed

    parts work together as a single unit. ...

    1. Click New, click Part, OK.

    2. Click Front Plane, insert sketch on plane by click Sketch.

    3. Click on Corner Rectangle, sketch a rectangle start at

    origin.

    and .

    4. Click Smart Dimension and dimension sketch as

    sketch below.

    and .

    5. Click Features>Extruded Boss/Base, on Direction 1

    set D1to 4in

    In this tutorial you will create this

    toy horse by assembly parts to one

    unit assembly.

  • 8/13/2019 Solidworks Tutorial For Beginner

    54/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 51

    and .

    6. Click on right faceand click Normal To.

  • 8/13/2019 Solidworks Tutorial For Beginner

    55/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 52

    7. Click on right faceagain and click Sketch.

    Click on Circle and sketch 4 circle at each corner. Click

    on Smart Dimension and dimension sketch as

    sketched below.

    8. Click on Features>Extruded Cut and set Direction 1 to

    Through All and . Click

    on View OrientationIsometric.

  • 8/13/2019 Solidworks Tutorial For Beginner

    56/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 53

    9. Click on top face and click Normal To.

    Click on top face again and click Sketch.

  • 8/13/2019 Solidworks Tutorial For Beginner

    57/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 54

    Click on Corner Rectangle and sketch 2 rectangles at

    top and bottom.

    Click on Smart Dimension and dimension theserectangles as sketched below.

  • 8/13/2019 Solidworks Tutorial For Beginner

    58/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 55

    10. Click on Features>Extruded Cut and set Direction 1 to

    1.0in

    and .

    Click on View Orientation>Isometric.

  • 8/13/2019 Solidworks Tutorial For Beginner

    59/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 56

    11. Save the part as Body.

    12. Click New, click Part, OK.

    13. Click Right Plane, insert sketch on plane by click Sketch.

    14. Click on Corner Rectangle, sketch a rectangle start at

    origin.

    and .

  • 8/13/2019 Solidworks Tutorial For Beginner

    60/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 57

    15. Click Smart Dimension and dimension sketch as

    sketch below.

    16. Click Centerline and sketch vertical

    centerline through top edge midpoint to bottom midpoint.

    Press Escto end centerline.

  • 8/13/2019 Solidworks Tutorial For Beginner

    61/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 58

    17. Click on Circle, sketch 3 circles onto centerline and

    using Smart Dimension dimension sketch as

    sketched below.

    18. Click Features>Extruded Boss/Base, on Direction 1

    set D1to 0.25in

    and . Click on View

    Orientation>Isometric.

  • 8/13/2019 Solidworks Tutorial For Beginner

    62/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 59

    19. To change part color, right click on

    Part2>Appearance>Appearance

    On Colorselect Shinyand pick whitecolor.

    and .

    20. Save the part as Leg.

    21. Click New, click Part, OK.

  • 8/13/2019 Solidworks Tutorial For Beginner

    63/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 60

    22. Click Right Plane, insert sketch on plane by click Sketch.

    23. Click on Circle, and sketch a circle. Click Smart

    Dimension dimension this circle to 0.25in.

    24. Click Features>Extruded Boss/Base, on Direction 1

    set D1to 0.25in

    and .

    25. Click on right faceand click Normal To.

    Click on this face againand click Sketch.

  • 8/13/2019 Solidworks Tutorial For Beginner

    64/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 61

    26. Click on Circle, and sketch a circle. Click Smart

    Dimension dimension this circle to 1.5in.

    27. Click Features>Extruded Boss/Base, on Direction 1

    set D1to 0.25in

    and .

    28. To change part color, right click on

    Part3>Appearance>Appearance

  • 8/13/2019 Solidworks Tutorial For Beginner

    65/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 62

    On Colorselect Standardand pick redcolor.

    and .

    29. Save the part as Wheel.

    30. Click New, click Part, OK.

    31. Click Right Plane, insert sketch on plane by click Sketch.

  • 8/13/2019 Solidworks Tutorial For Beginner

    66/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 63

    32. Click on Line, and sketch a horse head.

    33. Click on Smart Dimension and dimension sketch

    as sketched below.

    34. Click Features>Extruded Boss/Base, on Direction 1

    set D1to 0.5in

    and .

    35. To change part color, right click on

    Part4>Appearance>Appearance

  • 8/13/2019 Solidworks Tutorial For Beginner

    67/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 64

    On Colorselect Shinyand pick whitecolor.

    and .

    36. Save the part as Head.

    37. Click New, click Part, OK.

  • 8/13/2019 Solidworks Tutorial For Beginner

    68/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 65

    38. Click Right Plane, insert sketch on plane by click Sketch.

    39. Click on Line, and sketch a horse tail.

    40. Click on Smart Dimension and dimension sketch

    as sketched below.

  • 8/13/2019 Solidworks Tutorial For Beginner

    69/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 66

    41. Click Features>Extruded Boss/Base, on Direction 1

    set D1to 0.5in

    and .

    42. To change part color, right click on

    Part5>Appearance>Appearance

    On Colorselect Shinyand pick whitecolor.

  • 8/13/2019 Solidworks Tutorial For Beginner

    70/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 67

    and .

    43. Save the part as Tail.

    Lets begin assembly all this parts.

    44. Click New, click Assembly, OK.

    45. To add part in assembly, Click Browse

  • 8/13/2019 Solidworks Tutorial For Beginner

    71/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 68

    SelectBody.sldprt and clickOpen. Click on workspace.

    46. To add leg part, click Insert Components , click

    Browse

  • 8/13/2019 Solidworks Tutorial For Beginner

    72/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    73/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    74/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 71

    Coincident mate already pre selected, click .

    49. Turn the assembly back to previous view.

  • 8/13/2019 Solidworks Tutorial For Beginner

    75/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 72

    50. Click on inner hole face on bodyand inner hole of leg.

    The Concentric mate already pre selected, click . Repeat

    this step for bottom hole.

    and .

    51. Turn the assembly the other way.

  • 8/13/2019 Solidworks Tutorial For Beginner

    76/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 73

    52. Click on wheel shaft face and inner leg hole.

    Concentric mate already pre selected, click .

    53. Click on inner wheel face

    turn the assembly to left side and click on outer leg face.

    Coincident mate already pre selected, click .

    54. Repeat step 46 53 for other set of legs and wheels.

    55. To add head part, click Insert Components ,

    click Browse

  • 8/13/2019 Solidworks Tutorial For Beginner

    77/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 74

    SelectHead.sldprt and clickOpen. Click on workspace. To

    add tail part, click Insert Components , click

    Browse

    Select Tail.sldprt and clickOpen. Click on workspace.

  • 8/13/2019 Solidworks Tutorial For Beginner

    78/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    79/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 76

    Coincident mate already pre selected, click .

    58. Click on top edge of tail,

    turn assembly to view top body and click on top face of the

    body.

    Coincident mate already pre selected, click .

    59. Turn the model to facing front of the body, click on side face

    of inner cut,

  • 8/13/2019 Solidworks Tutorial For Beginner

    80/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 77

    turn the assembly to left and click on head side face.

    Coincident mate already pre selected, click .

    60. Click on inner cut face of the body,

    turn the assembly around and click on back head face.

  • 8/13/2019 Solidworks Tutorial For Beginner

    81/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 78

    Coincident mate already pre selected, click .

    61. Turn the assembly to view front side, click on head lower

    edge,

    and click on body bottom inner cut.

    Coincident mate already pre selected, click .

  • 8/13/2019 Solidworks Tutorial For Beginner

    82/104

    Beginner Part 6: Assembly Parts www.solidworkstutorials.com

    Beginner Part 6: Assembly Parts 79

    62. Click View Orientation>Isometric

    and youre done!

    63. Save the assembly as Horseand youre done! Simple

    isnt it?

    Go to table of contents

    Go to beginning of chapter tutorial

    Go to www.solidworkstutorials.com

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/
  • 8/13/2019 Solidworks Tutorial For Beginner

    83/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 70

    Beginner Part 7: Detailing Drawing

    Once solid parts created we need to transfer it to engineering

    drawing so the others can understand your parts

    1. Click New, click Drawing, OK.

    2. On Sheet Format/Sizeselect A Landscapeand OK.

    3. Click Browse...

    locate you Block.sldprt(Part from Beginner Part 5: Pattern

    tutorials)

    In this tutorial you create drawing

    for this part.

  • 8/13/2019 Solidworks Tutorial For Beginner

    84/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 71

    Click Open.

    4. For Orientation select Topand for Display Styleselect

    Hidden Lines Visible,

  • 8/13/2019 Solidworks Tutorial For Beginner

    85/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 72

    5. Click on sheet to add this view,

    click again on left side to add side view of the part,

    click once more to upper right of sheet to view its 3D view.

  • 8/13/2019 Solidworks Tutorial For Beginner

    86/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 73

    Click .

    6. Repositions part 3D view to upper right corner of the sheetby draggingit to this location.

    7. There is no centerline for holes in side view, lets add this

    centerline, click on side view,

  • 8/13/2019 Solidworks Tutorial For Beginner

    87/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 74

    Click on Annotationtab,

    click on Centerline,

    centerline automatically added to side view, click .

    8. Click Smart Dimension and click on bottom edgeand pull dimension to bottom.

  • 8/13/2019 Solidworks Tutorial For Beginner

    88/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 75

    9. Zoom in, click on center hole edge,

    click on counter bore hole edge

    and pull dimension to bottom side.

  • 8/13/2019 Solidworks Tutorial For Beginner

    89/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 76

    10. Click on center hole edge,

    click on counter bore hole edge

  • 8/13/2019 Solidworks Tutorial For Beginner

    90/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 77

    and pull dimension to bottom side.

    11. Repeat step 10and continue dimension for the third counter

    bore hole.

  • 8/13/2019 Solidworks Tutorial For Beginner

    91/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 78

  • 8/13/2019 Solidworks Tutorial For Beginner

    92/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    93/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 80

    13. Repeat step 12for right edge.

  • 8/13/2019 Solidworks Tutorial For Beginner

    94/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 81

    14. Click on center hole edge and pull out its diameter

    dimension.

  • 8/13/2019 Solidworks Tutorial For Beginner

    95/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    96/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 83

    16. Click on center hole edge,

    click on counterbore hole edge

    and pull its dimension to left side.

  • 8/13/2019 Solidworks Tutorial For Beginner

    97/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 84

    17. Click on center hole edge,

    click on bottom edge

    and pull its dimension to left side.

  • 8/13/2019 Solidworks Tutorial For Beginner

    98/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    99/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 86

    20. Click on thread

    and pull out its hole callout to right side.

    Click to end hole callout annotation.

  • 8/13/2019 Solidworks Tutorial For Beginner

    100/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    101/104

  • 8/13/2019 Solidworks Tutorial For Beginner

    102/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 89

    23. You can customize each view how its appear on drawing bychanging its display style. Click on Section A-Aview,

    on Display Styleclick on Hidden Line Removed.

    Click . Your section view now changed.

  • 8/13/2019 Solidworks Tutorial For Beginner

    103/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    Beginner Part 7: Detailing Drawing 90

    24. Click on 3D view,

    on Display Styleclick on Shaded With Edges.

    To change its scale, under Scaleclick on Use custom scale,

    set to 1:3

    and .

  • 8/13/2019 Solidworks Tutorial For Beginner

    104/104

    Beginner Part 7: Detailing Drawing www.solidworkstutorials.com

    25. Save the drawing as Blockand youre done! Simple isntit?

    Go to table of contents

    Go to beginning of chapter tutorial

    Go to www.solidworkstutorials.com

    http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/